Chief CMS443 mounting kit
Contents
1. 10 x 5 8 10 x 1 4 10 x 1 4 5 32 4 8mm x 16mm 4 8mm x 6 4mm 4 8mm x 6 4mm 4 0mm Installation Instructions CMS440 PREPARATION 1 Determine exact location of extension column accessory not included on suspended ceiling Mark location on lower finished side of ceiling tile with pencil See Figure 1 Be sure to consider the following items when determining column location Dimensional offset of display projector relative to column due to mount and or interface e For Projectors Any recommended dimensions of projector relative to target See installation instructions included with the projector Figure 1 Remove affected ceiling tile and any adjacent tiles required for access Press center tip of tool M into finished side of ceiling tile at marked location Cut extension column hole through tile using back and forth hand twisting motion Reinstall ceiling tile with extension column hole Ensure tile is oriented for proper location of hole Install tray A on top of ceiling tile so that end brackets engage primary 1 1 2 38mm high rails of ceiling framework See Figure 2 Figure 2 Loosen four extension column support wing nuts in upper side of tray A See Figure 2 Position tray A and or extension column support as required to center support over ceiling tile hole See Figure 2 Tighten wing nuts See Figure 2 OPTIONAL Mark location of electr2. de apparatuur Degene die de structuur monteert waaraan deze component is bevestigd is ervoor verantwoordelijk dat deze minimaal vijf 3 CMS440 Installation Instructions maal het gezamenlijke gewicht van alle apparatuur kan dragen Zonodig dient u de structuur v r de montage van de component te versterken A WAARSCHUWING Overschrijding van het draagvermogen kan de oorzaak zijn van ernstig persoonlijk letsel en beschadiging van de apparatuur Degene die het product installeert is ervoor verantwoordelijk dat het totale gewicht van alle componenten die aan de CMS440 worden bevestigd een gewicht van 22 kg niet overschrijdt IMPORTANTS AVERTISSEMENTS et PR CAUTIONS A ADVERTISSEMENT Un ADVERTISSEMENT vous met en garde contre les possibilit s de blessures graves ou de danger de mort si vous ne suivez pas les instructions A PRECAUTION Une PRECAUTION vous met en garde contre les possibilit s d endommagements et de destruction de l quipement si vous ne suivez pas les instructions correspondantes DIMENSIONS A ADVERTISSEMENT Le manque de la lecture de la compr hension et du respect total de toutes les instructions peut entrainer des blessures corporelles graves endommager l quipement ou annuler la garantie d usine Il incombe l installateur de s assurer que tous les composants sont correctement assembl s et install s l aide des instructions fournies A ADVERTISSEMENT L absence de l a
3. the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the CMS440 does not exceed 50 lbs 22 kg AVISOS y PRECAUCIONES A IMPORTANTES A AVISO Un AVISO llama su atenci n sobre la posibilidad de sufrir lesiones de gravedad o incluso mortales si no sigue las instrucciones A PRECAUCION Una nota de PRECAUCION llama su atenci n sobre la posibilidad de da ar o destruir el equipo si no sigue las instrucciones A AVISO Si no lee comprende perfectamente y sigue todas las instrucciones podria causar da os graves da os personales y materiales o anular la garantia de fabrica El instalad
4. INSTALLATION INSTRUCTIONS Instrucciones de instalaci n Istruzioni di installazione Installationsanleitung Installatie instructies Instruc es de Instalac o Instructions d installation Lightweight Suspended Ceiling Kit Juego de techo ligero suspendido Leichtgebauter H ngedecken Kit Kit de instala o de teto suspenso leve Kit di sospensione a soffitto leggero Licht vrijhangend plafondkit Kit de plafond suspendu l ger QG CHIEF CMS440 CMS440 Installation Instructions DISCLAIMER CSAV Inc and its affiliated corporations and subsidiaries collectively CSAV intend to make this manual accurate and complete However CSAV makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind CSAV makes no representation of warranty expressed or implied regarding the information contained herein CSAV assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow
5. age to equipment 1 Drill 1 4 6 4mm diameter x 1 3 8 35mm deep hole at each marked cable anchor support location See Figure 4 Ensure hole is at least 2 1 2 64mm from nearest concrete m edge Remove debris from hole Wood Ceiling Structure 1 Drill 5 32 4 0mm diameter x 2 51mm deep hole at each marked cable anchor support location See Figure 6 Remove debris from hole Figure 5 Figure 6 Figure 4 2 Fully thread eye lag E into each hole See Figure 6 2 Tap anchor D into each hole to a depth of at least 1 25mm See Figure 4 3 Route end of cable C through eye lag E and then through cable loop See Figure 6 Repeat for 3 remaining support locations WARNING Failure to properly set anchor may result in failure of anchor and serious personal injury or damage to equipment 3 Using claw portion of hammer set each anchor D by pulling it out of hole approximately 1 4 6 4mm See Figure 4 4 Insert portion of manufactured oop on cable C through hole in anchor D See Figure 4 Insert end of cable C through loop Repeat for 3 remaining support locations Installation Instructions CMS440 TRAY INSTALLATION 1 Reinstall ceiling tile with extension column hole Ensure tile is oriented for proper location of hole Reinstall tray A on top of ceiling tile so that extension column support is centered over hole in tile Position tray A with four screws G as requir
6. dos de acordo com as instru es fornecidas A ADVERT NCIA Se n o for proporcionado apoio estrutural adequado a este componente podem ocorrer graves les es pessoais ou danos no equipamento E da responsabilidade do instalador certificar se de que a estrutura a qual este componente ligado pode suportar cinco vezes o peso combinado de todo o equipamento Reforce a estrutura conforme necessario antes de instalar o componente A ADVERTENCIA Exceder a capacidade de peso pode resultar em graves les es pessoais ou danos no equipamento E da responsabilidade do instalador certificar se de que 0 peso combinado de todos os componentes ligados ao CMS440 nao excede 22 kg AVVERTENZE e PRECAUZIONI A IMPORTANTI A AVVERTENZA Un AVVERTENZA mette in guardia in merito alla possibilita di gravi infortuni anche letali qualora non si osservino le istruzioni A ATTENZIONE Un ATTENZIONE indica la possibilit di gravi danni all attrezzatura qualora non ci si attiene alle istruzioni al riguardo A AVVERTENZA La mancata comprensione e ottemperanza alle istruzioni fornite pu provocare gravi lesioni personali danni all apparecchiatura o annullare la garanzia fornita dal produttore Spetta all installatore verificare che tutti i componenti siano assemblati correttamente e installati secondo le istruzioni fornite A AVVERTENZA Una resistenza strutturale inadeguata per questo componente pu arrecare gravi infortuni o danne
7. e il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster By Hand A mano Von Hand Com amao A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option Target of Projector Punto de enfoque del proyector Ziel des Projektors Mira do projector Punto di proiezione Doel van de projector Cible du projecteur Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguran a Chiave di sicurezza Veiligheidssleutel Cl de s curit 910 lt 010 Hammer Martillo Hammer Martelo Martello Hamer Marteau CMS440 Installation Instructions TOOLS REQUIRED FOR INSTALLATION a 1 4 6 4mm 5 32 4 0mm C 4 1 16 x 25 1 6mm x 7 6m E 4 1 4 x 2 0 262 x 1 5 16 6 4mm x 51mm 6 7mm x 33mm G 4 H 1 J 1 K 1 L 1 1 1
8. ed For 24 610mm Framework Install screws through end bracket inside holes See Figure 7 e For 600mm 23 5 8 Framework Install screws through end bracket outside holes See Figure 8 Figure 8 CAUTION Failure to properly tension cables C may result in damage to ceiling tile framework 4 Thread each cable C completely through cable lock F corresponding hole in corner of tray A and completely through opposite side of cable lock F See Figure 9 Adjust cable tension until tray A is supported entirely and evenly by all four support cables but not so tight as to distort ceiling tile framework NOTE Cable lock F will allow cable to enter from only one direction per side indicated by arrows on lock Depress spring loaded pins on cable lock F to release cable tension Figure 9 CMS440 Installation Instructions EXTENSION COLUMN INSTALLATION 3 Install finishing ring B on extension column below ceiling tile See Figure 11 If necessary bend four tabs inward to secure ring to column WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the CMS440 up to and including the display projector does not exceed 50 Ibs 22 kg 1 Install the extension column accessory not included to the extension column support See installation instructions includ
9. ed with the accessory NOTE f installation instructions are not available contact Chief Manufacturing for assistance 2 Using hex key L secure extension column by one of the following methods See Figure 10 e Install screw H into extension column support tightening firmly against column e OPTIONAL Install security screw J through locking collar K into extension column support tightening firmly against column NOTE Locking collar K is designed to spin even when screw J is tight Figure 11 4 Reinstall remaining ceiling tiles as required Figure 10 10 Installation Instructions CMS440 CHIEF SANUS AUDIO VISUAL MANUFACTURERS DECLARATION OF CONFORMITY For Product identification Model type CMS440 Category description Mounting devices Stands and other Accessories to be used with entertainment electronics Brand Chief Manufacturer CSAV Inc 8401 Eagle Creek Parkway Savage MN 55378 EU Representative Concerning CSAV Inc Fellennoord 130 5611 ZB Einhoven The Netherlands 31 0440 2668620 A sample of Not Applicable CSAV Inc the product has been tested by Test report reference Applied standards EN 60063 2002 Means of conformity We declare under our sole responsibility that this product is in conformity with Directive 93 68 EEC Marking 98 37 EC Machinery 2001 95 EC Safety and or complies to the ess
10. ential requirements and all other relevant provisions of the based on test results using non harmonized standards in accordance with the Directives mentioned 11 CMS440 Installation Instructions i CHIEF 8810 000013 RevA 2006 Chief Manufacturing www chiefmfg com 04 07 USA International Europe Asia Pacific T U 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Room 301 Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA Post Code 518112 RAI HAS WAS AR BS E IS DFO 86 755 8996 9226 8996 9236 8996 9220 86 755 8996 9217
11. ggiare l apparecchiatura E responsabilit dell installatore verificare che la struttura alla quale fissato il componente sostenga con sicurezza cinque volte il carico combinato di tutta l apparecchiatura Rinforzare la struttura secondo necessit prima di installare i componenti A AVVERTENZA Un peso superiore alla capacita nominale pu arrecare gravi infortuni o danneggiare l apparecchiatura E responsabilit dell installatore verificare che il peso totale di tutti i componenti montati sul CMS440 non superi 22 kg 50 Ib BELANGRIJKE AANWIJZINGEN en WAARSCHUWINGEN A WAARSCHUWING Een WAARSCHUWING vestigt uw aandacht op de mogelijkheid van ernstig of dodelijk letsel als u de instructies niet opvolgt A VOORZICHTIG De aanwijzing VOORZICHTIG vestigt uw aandacht op de mogelijkheid van beschadiging of onherstelbare beschadiging van de apparatuur als u de betreffende instructies niet opvolgt A WAARSCHUWING Door niet alle instructies te lezen volledig te begrijpen en op te volgen riskeert u ernstig persoonlijk letsel beschadiging van de apparatuur en het vervallen van de fabrieksgarantie Degene die het product installeert is ervoor verantwoordelijk dat alle onderdelen aan de hand van de meegeleverde handleiding op de juiste wijze worden samengebouwd en gemonteerd A WAARSCHUWING Als u voor deze component onvoldoende constructiesterkte beschikbaar stelt riskeert u ernstig persoonlijk letsel of beschadiging van
12. ical cutout on ceiling tile with pencil See Figure 2 Examine ceiling structure concrete steel truss or wood above tray A to identify four support cable anchor locations Each location should be approximately 15 outboard of support holes in tray A See Figure 3 Mark locations with pencil Figure 3 11 Remove tray A and ceiling tile 12 OPTIONAL Cut electrical box opening in ceiling tile at marked location Install box to tray A NOTE Electrical box attach hardware and cutting tool not included CMS440 Installation Instructions SUPPORT CABLE INSTALLATION Steel Truss Ceiling Structure 1 Route end of cable C over truss at marked cable anchor support location and then through cable loop See Figure 5 Repeat for 3 remaining support locations WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component Solid Concrete Ceiling Structure WARNING Anchors must be installed into structurally sound solid concrete Installation into hollow concrete block mortar or concrete that exhibits cracking spalling or other defects may result in failure of anchor and serious personal injury or dam
13. or es el responsable de asegurarse de que todos los componentes estan correctamente montados e instalados siguiendo las instrucciones indicadas A AVISO Si no se proporciona la resistencia estructural adecuada para este componente podrian provocarse graves da os personales o materiales El instalador es el responsable de asegurarse de que la estructura a la que este componente esta sujeta puede soportar cinco veces el peso combinado de todo el equipo Refuerce la estructura segun sea necesario antes de instalar el componente A AVISO Si se excede el peso maximo podrian causarse graves da os personales o materiales El instalador es responsable de asegurarse de que el peso combinado de todos los componentes montados en el CMS440 no excede 22 kg 50 libras WICHTIGE WARN und A VORSICHTSHINWEISE A WARNUNG Ein WARNHINWEIS macht auf m gliche schwere oder t dliche Verletzungen aufmerksam die bei Nichtbefolgung der Anweisungen eintreten k nnen A VORSICHT Ein VORSICHTSHINWEIS macht auf Schaden oder m gliche Zerst rung des Ger ts aufmerksam die bei Nichtbefolgung der Anweisungen eintreten k nnen A WARNUNG Falls nicht alle Anweisungen gelesen und gut verstanden werden kann dies zu schweren K rperverletzungen Schaden an den Geraten f hren und die Werksgarantie nichtig machen Der Monteur ist daf r verantwortlich dass alle Komponenten unter Einhaltung der mitgelieferten Anweisungen korrekt zusammengebaut
14. pport d une r sistance structurelle appropri e pour ce composant peut entrainer des blessures corporelles graves ou endommager l quipement Il incombe l installateur de s assurer que la structure a laquelle le composant est attach peut soutenir cinq fois le poids combin de tout l quipement Renforcer la structure selon les besoins avant l installation du composant A ADVERTISSEMENT D passer la capacit pond rale peut entrainer des blessures corporelles graves ou endommager l quipement Il incombe l installateur de s assurer que le poids combin de tous les composants attach s CMS440 n est pas sup rieur 22 kg 50 lb Cp 8 00 F 203 X 3 50 OD 23 44 OD 595 2X 7 00 OD 6 26 159 4 76 121 89 178 o e o Installation Instructions CMS440 LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con lapiz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentar
15. und eingebaut werden A WARNUNG Wenn fir diese Komponente keine ausreichende bauliche Tragkraft vorhanden ist kann dies zu schweren K rperverletzungen oder Sch den an den Ger ten f hren Der Installateur ist daf r verantwortlich zu berpr fen ob die Wand an der diese Komponente verankert wird das F nffache der Gesamtlast aller befestigten Ger te sicher Installation Instructions CMS440 tragen kann Andernfalls muss die Wand verst rkt werden bevor die Komponente angebracht wird A WARNUNG Wenn das zulassige Gewicht Uberschritten wird kann dies zu schweren K rperverletzungen oder Sch den an den Ger ten f hren Der Monteur ist daf r verantwortlich dass das kombinierte Gewicht aller Komponenten die am Modell CMS440 befestigt sind nicht mehr als 22 kg betr gt ADVERT NCIAS e AVISOS IMPORTANTES A ADVERTENCIA Os alertas de ADVERTENCIA avisam no para a possibilidade de ocorr ncia de graves les es ou morte no caso de incumprimento das instru es A AVISO Os alertas de AVISO avisam no para a possibilidade de danos ou destrui o do equipamento no caso de incumprimento das instru es A ADVERT NCIA Se n o ler compreender completamente e seguir todas as instru es podem ocorrer graves les es pessoais danos no equipamento e a garantia de fabrica pode ser anulada E da responsabilidade do instalador certificar se de que todos os componentes sao correctamente montados e instala
Download Pdf Manuals
Related Search