Chief PDR2081S flat panel wall mount
Contents
1. 689 2712 PDR FULL LEFT PDR Series Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con l piz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster C d E Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche XA Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel2. Bp NN Adjustment nut Figure 3 Installing Covers and End Caps NOTE The covers and end caps have pressure fitting ends that lock into place with each other 1 Install cover B over the top bracket See Figure 4 2 Install end caps C and D into the cover and top bracket See Figure 4 3 Repeat Steps 1 and 2 for the lower mounting bracket See Figure 4 Figure 4 Mounting the Display WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Displays can weigh in excess of 40 1 5 18 1kg ALWAYS use two people and proper lifting techniques when installing display WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make sure mounting buttons on display are properly seated in mounting holes in faceplate 1 Move mount faceplate to extended position by grasping faceplate and pulling outward away from wall 2 While supporting both sides of display align four mounting buttons on display or interface bracket with four mounting holes in faceplate See Figure 5 3 Lower display into place listening for audible click to ensure recessed area of mo nting buttons are properly seated in lower area of mounting holes and ClickConnect mechanism has engaged See Figure 5 and See Figure 6 NOTE Holes are provided in the faceplate for use with a padlock or si
3. Chave de cabeca sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Installation Instructions PDR Series TOOLS REQUIRED FOR INSTALLATION e 7 32 5 5mm lt is jii 9 16 Adjustment wrench 1 Adjustment insert Listed PSBU interface bracket provided with Listed Model PDRUS B but shown PDR assembly J 12 5 1 2 G 4 850x 393x 135 H 4 5 16 x 3 B 2 Cover D 2 End cap PDR Series Installation Instructions MOUNT INSTALLATION Installing Mount to Wall WARNING IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installer s responsibility to make sure the structure to which the mount is being installed is capable of supporting five times the combined weight of the mount and all attachments 1 Determine mounting location taking into consideration display size and PDR s range of movement 2 Using a stud sensor locate two wood studs 16 apart on center See Figure 1 Figure 1 3 Placeandlevel mount against wall aligning mounting holes in upper and lower wall channels with studs See Figure 1 4 Mark four mounting holes making sure mounting holes are located as close as possible to center of studs See Figure 1 5 Drill four 7 32
4. HEIGHT ADJUSTMENT 17 WILL ADD BETWEEN 1 2 AND 2 IN DEPTH TILT ROLL YAW 5 11 1 4 AND MAY AFFECT LOCATION OF DISPLAY 483 ON THE MOUNT m 19 00 86 SEE PSB XXXX DRAWING ALSO 3 40 i 178 235 217 7007 1125 DEPTH 57 __ 1 00 1 00 2 25 i Col gt C y Xr 3 a 500 Een j 19 69 PU 4 95 N 560 22 04 VEO DPD 6 Er M EX B 600 23 62 END CAP TO END CAP PDR Series Installation Instructions DIMENSIONS Unit Depth n Tit Adjustment Tilted Up Extended Retracted A e e BEE H 3 40 D spes 1003 D Tilted Down j d 39 50 uU The range of adjustment will vary with different weight and depth screens N Highest Height Setting e JO d 64 lt aree 2 5 2 9 Roll Adjustment
5. pilot holes where the mounting holes were marked See Figure 1 6 Install two 5 16 x 3 lag bolts H and two 0 135 thick washers G through mounting holes in upper wall channel and into pilot holes DO NOT tighten at this time See Figure 2 7 Place mount against wall aligning mounting holes in upper wall channel with lag bolts and hang mount on lag bolts making sure washers are located in front of mount 10 Adjust mount lateral position left until lag bolts are seated in mounting slots in upper wall channel See Figure 2 Install two 5 16 x 3 lag bolts H and two 0 135 thick washers G through mounting holes in lower wall channel and into pilot holes See Figure 2 Tighten all hardware DO NOT overtighten Figure 2 Adjusting PDR Height NOTE Height adjustment range up to 1 08 inches 1 Check PDR for the desired height If needed use the adjustment wrench E to adjust the PDR height See Figure 3 Turn adjustment nut clockwise to lower the unit height or Turn adjustment nut counterclockwise to raise the unit height Installation Instructions PDR Series o E o aem Neos eL F
6. 0 1 Locate the adjustment insert F and wrench E provided with the mount 2 Place adjustment insert into socket head cap screw located at swing arm pivot point See Figure 14 NOTE The display may need to be repositioned in order to gain access to the tension adjustment screw s 3 Using the wrench provided with the mount turn adjustment insert clockwise to increase swing arm tension or counterclockwise to reduce swing arm tension See Figure 15 NOTE Small adjustments of 1 8 turn or less are typically all that is required to achieve desired tension 4 Check swing arm tension If desired tension is present tension adjustment is complete If additional tension adjustment is required repeat steps 2 and 3 until desired tension is achieved NOTE If changing from a smaller display to a larger display it may be necessary to increase swing arm tension Socket Head Capscrew Figure 14 Increase Figure 15 Installation Instructions PDR Series Removing Display from Mount 1 Remove bolt or padlock from faceplate if used NOTE The pin may have been used as a more permanent locking device If so remove nut and pin and move from the lower holes to the upper holes 2 Pull back on flag on upper mounting hole and press pin down into Open position See Figure 16 WARNING DISPLAY MAY WEIGH IN EXCESS OF 40 LBS Always use two people and proper lifting techniques when installi
7. INSTALLATION INSTRUCTIONS Large Flat Panel Dual Arm Wall Mount CHIEF PDR Series Our Mounts Your Vision PDR Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and WARNING Failure to read thoroughly understand and subsidiaries collectively Milestone intend to make this follow all instructions can result in serious personal injury manual accurate and complete However Milestone makes no damage to equipment or voiding of factory warranty Itis the claim that the information contained herein covers all details installer s responsibility to make all components are conditions or variations nor does it provide for every possible properly assembled and installed using the instructions contingency in connection with the installation or use of this provided product The information contained in this document is subject to change without notice or obligation of any kind Milestone WARNING Failure to provide adequate structural strength makes no representation of warranty expressed or implied for this component can result in serious personal injury or regarding the information contained herein Milestone assumes damage to equipment It is the installer s responsibility to no responsibility for accuracy completeness or sufficiency of make sure the structure to which this component is attached the information contained in this document can
8. al Tilt Tension Adjustment 1 With display mounted check for desired vertical tilt tension 2 Adjust the Centris Select knob until desired vertical tilt Mna alt tension is obtained See Figure 8 OCK Screw 3 Tolock the mount at the desired vertical tilt tighten the vertical tilt lock screw See Figure 9 Figure 9 Installation Instructions PDR Series Lateral Tilt Tension Adjustment CAUTION DO NOT OVERTIGHTEN LATERAL TILT ADJUSTMENT NUT Overtightening lateral tilt adjustment will cause excessive wear and may distort adjustment components 1 Using a 9 16 wrench not provided slightly tighten or loosen lateral tilt tension adjustment nut See Figure 10 2 Attach the display and check for desired tilt tension 3 Repeat Steps 1 and 2 until desired tilt tension is obtained Rotational Tilt Tension Adjustment 1 If necessary loosen or tighten bottom rotational tilt tension adjustment nut See Figure 10 2 Attach the display and check for desired rotational tilt tension 3 Repeat Steps 1 and 2 until desired rotational tilt tension is obtained P e fe L Lateral Tilt Adjustment Nut e Rotational Tilt Adjustment Nut Figure 10 Swing Arm Adjustments The dual swing arms are shipped installed in the
9. center of the top and bottom mounting brackets which is the standard mounting configuration The top and bottom mounting brackets have slotted holes allowing for lateral adjustment of the dual swing arms After the top and bottom mounting brackets have been installed between two wood studs 16 on center the swing arms can be adjusted or moved off center depending on the location of the mount the size of the display and the lateral movement needed to rotate the display The swing arms can be adjusted as follows Adjusting the Swing Arms Off Center With no disassembly required you can adjust the swing arms up to 1 inch to the left of center or up to 1 inch to the right of center e Reconfiguring the Swing Arms Left of Center With some disassembly and reassembly required you can move the swing arms to the left of center by reconfiguring the mount Use the first and third slotted holes in the top and bottom mounting brackets e Reconfiguring the Swing Arms Right of Center With some disassembly and reassembly you can move the swing arms to the right of center by reconfiguring the mount Use the third and fifth slotted holes in the top and bottom mounting brackets Adjusting the Swing Arms Off Center 1 Remove the display from the mount 2 Loosen four bolts two on the top and two on the bottom securing the swing arm assembly to the top and bottom mounting brackets See Figure 11 3 Move the swing arm assembly to de
10. milar locking device if desired In addition he pin and nut may be removed from the upper holes and moved to the lower holes for use as a more permanent locking device See Figure 6 Figure 5 Touseasa more permanent lock remove pin and nuts and move to lower holes A padlock or bolt may be placed through latch holes Figure 6 PDR Series Installation Instructions 5 cable clamps Figure 7 Cable Management Centris Select Adjustment Knob WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO 1 EQUIPMENT Make sure cables do not run through pinch points 1 Loosen front and rear cable clamps on top arm See Figure 7 2 Thread cable ties J under cable clamps and secure clamps to top arm See Figure 7 3 Route power audio video cables through the cable channel in top arm See Figure 7 allowing sufficient slack in cables for left Right movement of display and swing arm and also swing arm extension and retraction 4 Secure cables to top arm using two cable ties J 5 Repeat Steps 1 through 4 as necessary for remaining top Figure 8 arm and lower arms WARNING IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT DO NOT route cables through holes in faceplate Tension Adjustments Vertic
11. ng or positioning display on mount 3 Carefully lift display from mount 4 Liftupon pin and place flag back against faceplate to return it to Closed position Remove bolt or padlock if used Pin in Closed position move to Open position to remove display Pin in Open position move to Closed position after display is removed A Figure 16 11 PDR Series Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8831 000005 RevM 2010 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 08 10 USA International Europe Asia Pacific p TI U gt 0 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 SCH at n
12. sired location 4 Tighten the bolts 5 Install the display on the mount Top Bolts Figure 11 Reconfiguring the Swing Arms to the Left or Right of Center 1 Remove the display from the mount 2 Remove four bolts two on the top and two on the bottom securing the swing arm assembly to the top and bottom mounting brackets See figure 14 PDR Series Installation Instructions WARNING The next step will release the arm assembly from the mount The arms and plate may fall if you are not careful 3 Move the swing arm assembly to desired location Left of Center See Figure 12 Right of Center See Figure 13 4 Install retaining pin assemblies one top and one bottom and secure using two bolts one top and one bottom 5 Install four bolts two on the top and two on the bottom to secure the swing arm assembly to the top and bottom mounting brackets 6 Tighten the bolts 7 Install the display on the mount Top Bolts Figure 12 Top Bolts Figure 13 Swing Arm Tension Adjustment Swing arm tension is pre set at the factory and is adjusted to accommodate displays with weights near the top of the mounts capacity If smaller displays are used it may be difficult to reposition the display after mounting Swing arm tension can be adjusted to compensate for smaller display by NOTE The display must be mounted prior to adjusting swing arm tension 1
13. support five times the combined weight of all equipment Reinforce the structure as required before installing the component The wall to which the mount is being attached ief i i i AV Technologies Chief is a registered trademark of Milestone echnologies may have a maximum drywallihickness of 5 6 All rights reserved WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the IMPORTANT WARNINGS AND installer s responsibility to make sure the combined weight of CAUTIONS all components attached to the PDR does not exceed 200 Ibs 90 7 kg Use with products heavier than the maximum weight indicated may result in collapse of the mount and its WARNING A WARNING alerts you to the possibility of accessories causing possible injury serious injury or death if you do not follow the instructions PDR Series contains the following models A PDR2000S PDR2000B CAUTION A CAUTION alerts you to the possibility of PDRUS PDRUB damage or destruction of equipment if you do not follow the corresponding instructions NOTSHOWN THE CUSTOM INERPACE THAT CT it is i 200 LBS BRACKET NEEDED FOR YOUR DISPLAY Mou nting Pattem
Download Pdf Manuals
Related Search