Baumatic P68SS hob
Contents
1. o Reassemble all the burners carefully in particular you should make sure that the flame spreader is correctly placed on the burner o IMPORTANT The minimum flow adjustment process must be completed before the appliance is next used 20 Minimum flow adjustment for hob gas taps All work must be carried out by a CORGI registered engineer IMPORTANT Always isolate the hob from the electricity supply before changing the injectors and or adjusting the minimum flow of the burners o Switch the burner on and set the knob at the minimum position o Remove the knob from the tap and place a small bladed screwdriver in the centre of the tap Shaft o Unscrew the adjusting screw in order to increase the gas flow or tighten the adjusting screw to decrease the gas flow o The correct adjustment is obtained when the flame has a length of about 3 4mm o For butane propane gas the adjusting screw must be tightly screwed In o Refit the control knob o Make sure that the flame does not go out by quickly turning from maximum flow to minimum flow If it does then remove the control knob and make further adjustments to the gas flow testing it again once the adjustment has been made o Repeat this process for each one of the gas taps 21 Gas tap maintenance A N These maintenance operations MUST ONLY be carried out by a CORGI registered engineer IMPORTANT Before carrying out any maintenance operations d2. Instruction manual User Manual for your Baumatic P61SS P62SS Pythagora 4 burner 60cm gas hob P67SS P68BL P68SS Pythagora 5 burner 70cm gas hob x Baumatic You will be mine NOTE This User Instruction Manual contains important information including safety amp installation points which will enable you to get the most out of your appliance Please keep it in a safe place so that it is easily available for future reference for you or any person not familiar with the operation of the appliance DD 07 08 08 Contents Environmental note Important safety information Specifications Product amp Aperture dimensions Product specifications Standard accessories Electrical details Gas details Gas hob surface layout Using the gas hob Before first use Turning the hob on Automatic electric ignition Energy saving tips Cleaning Cleaning the hob top After each use Cleaning the hob burners Installation Positioning Unpacking the appliance Installing the appliance Gas connection Ventilation requirements Gas Safety Installation and Use Regulations Gas Adjustment Conversion to LPG Minimum flow adjustment for hob gas taps Gas tap maintenance Electrical connection Replacing the mains supply cable My appliance isn t working correctly Contact details 13 1 Environmental note This appliance is marked according to the European directive 2002 96 EC on Waste electri
3. P61SS amp P62SS Control panel Auxiliary burner 1 00 kW Using the gas hob IMPORTANT You should clean the hob surface see Cleaning and maintenance section The following symbols will appear on the control panel next to each control knob 6 Black circle gas off Large flame maximum setting Small flame minimum setting o The minimum setting is at the end of the anti clockwise rotation of the control knob o All operation positions must be selected between the maximum and minimum positions o Never select a knob position between the maximum and off position Automatic electric ignition To ignite a burner o Press in the control knob of the burner that you wish to light and turn it anti clockwise to the minimum position o If you keep the control knob depressed the automatic ignition for the burner will operate o As each burner has a flame failure safety device once the burner has lit you will need to keep the control Knob pressed in for approximately 10 seconds o If after you let go of the control knob the flame goes out you Should repeat the above process o Incase of power failure the burners can be lit by carefully using a match o Ifthe burner flame goes out once it Is lit then the flame failure Safety device will cut the supply of gas to the burner 10 Energy saving tips BURNERS RAPID 180 mm SEMIRAPID 120 mm AUXILIARY 80 mm WORK 220 mm o The diametre of th
4. burners The hob burners should be cleaned once a week or more frequently if they get soiled o IMPORTANT Make sure that the hob surface pan supports and hob burners have cooled before you attempt to touch them o Remove the hob burners by pulling them upwards and away from the hob top o Soak them for about ten minutes in hot water and a little detergent o After cleaning and washing them wipe and dry them carefully o Before placing the burners back on the hob top make sure that the gas jet is not blocked 12 o IMPORTANT Make sure that you reassemble the burners in the Original way Installation The installation must be carried out by a CORGI registered installer in accordance with the current version of the following o Gas safety Regulations Installation amp Use o Building Regulations issued by the Department of Environment o Building Standards Issued by the Scottish Development Department o IEE Wiring Regulations o Electricity at Work Regulations BS 6172 o Installation of Domestic Gas Cooking Appliances if necessary BS 5482 Installation of Domestic LPG Appliances o BS 5440 Installation of Flues and Ventilation for Gas Appliances o Baumatic Ltd Installation Instructions 13 Positioning The adjacent furniture must be able to withstand a AN minimum temperature rise of 85 C above the ambient temperature of the room it is located in during periods of use Clearances required when
5. in accordance with the current edition of the Gas Safety Installation and Use Regulations It is in your interest and that of safety to ensure compliance with the law In the UK CORGI registered installers work to safe standards of practice The cooker must also be installed in accordance with the current edition of BS 6172 Failure to install the cooker correctly could invalidate the warranty liability claims and lead to prosecution Put the gas seal into the elbow Fully tighten the elbow and seal onto the gas rail The elbow MUST be pointing in a downwards direction Gas pressure may be checked on a semi rapid hob burner Remove the appropriate injector and attach a test nipple Light the other burners and observe that the gas pressure complies with the gas standards in force IMPORTANT On completion carry out a gas soundness test 19 Gas adjustment Conversion to LPG All work must be carried out by a CORGI registered engineer IMPORTANT Always isolate the cooker from the electricity supply before changing the injectors and or adjusting the minimum flow of the burners o Remove the pan stands burners and flame spreaders A o Unscrew the injector B and replace it with the stipulated injector for the new gas Supply see table below GENERAL INJECTORS JASLE _ Bumers Position typ Rapid 5 NATURAL 7 Semi rapid Auxiliary Wok L P G Rapid BUTANE 30 Semi rapid PROPANE Aux llary
6. ak Republic Baumatic Slovakia s r o Skultetyho 1 831 04 Bratislava 3 Slovakia 421 255 640 618 Germany Baumatic Gmbh J anderstrasse 9 Mannheim 68199 Germany 4962 112 9190 www baumatic de Italy Baumatic Italia S R L Via Caltana 129 Campodarsego Padova 35011 Italy 3904 9920 2297 www baumatic it Holland Baumatic Benelux B V Grindzuigerstraat 22 1333 MS ALMERE The Netherlands 3136 549 1555 www baumatic nl 23 26 27 www baumatic cam
7. as a door which opens directly to the outside If the room has a volume of less than 5m it will require an air vent of 100cm effective area If it is installed in a room with a volume that exceeds 11m then no air vent is required If there are any other fuel burning appliances in the same room the current edition of BS 5440 Part 2 should be consulted to determine air vent requirements Ensure that the room containing the cooker is well ventilated keep natural ventilation holes or install a mechanical ventilation device mechanical cooker hood Prolonged intensive use of the appliance may call for additional ventilation either by the opening of a window or by increasing the level of the mechanical ventilation device where present This hob is not fitted with a device for discharging the products of combustion Ensure that the ventilation rules and regulations are followed The walls behind and near the hob should be resistant to heat steam and condensation Remember that the quantity of air necessary for combustion must never be less than 2m h for each kW of power see total power in kW on the appliance rating plate 18 Gas Safety Installation and Use Regulations IMPORTANT The appliance MUST be connected to the gas supply by use of a 72 BSP Elbow seal copper pipe and an isolation tap fitted in an easily accessible position O It is the law that all gas appliances are installed by competent persons
8. cal and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The symbol akis on the product or on the documents accompanying the product indicates that this appliance may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product ss e l o The packaging materials that Baumatic uses are environmentally friendly and can be recycled o Please discard all packaging material with due regard for the environment Important safety information Your safety is of the utmost importance to Baumatic Please make sure that you read this instruction booklet before attempting to install or use the appliance If you are unsure of any of the information contained in this booklet please contact the Baumatic Technical Department General I nformation o This appliance is designed for domestic household use and for th
9. e bottom of the pan should correspond to that of the burner o The burner flame must never extend beyond the diametre of the pan o Use flat bottomed pans only o When possible keep a lid on the pan whilst cooking o Cook vegetables with as little water as possible to reduce cooking times IMPORTANT Always place pans centrally over the hob burners and position them so that the handles cannot get accidentally caught or knocked off You should also make sure that the handle is not over one of the other hob burner flames 11 Cleaning Cleaning operations must only be carried out when the hob is cool The appliance should be disconnected from your mains supply before commencing any cleaning process Cleaning the hob top agents will damage it You should remove any residues with Any residues that are left on the hob top surface from cleaning water and a little washing up Abrasive cleaners or sharp objects will damage the hob surface you should clean it using water and a little washing up liquid Although it is easier to clean some deposits whilst the hob surface is still warm Make sure that the hob surface pan supports and hob burners have all cooled sufficiently before you attempt to touch them After each use o Remove the pan supports and wipe the appliance over with a damp cloth and a little washing up liquid o Dry the appliance by rubbing the surface with a soft clean cloth Cleaning the hob
10. e cooking and frying of domestic foodstuffs o IMPORTANT The adjacent furniture and all materials used in the installation must be able to withstand a minimum temperature of 85 C above the ambient temperature of the room it is located in whilst in use o Certain types of vinyl or laminate kitchen furniture are particularly prone to heat damage or discolouration at temperatures below the guidelines given above o Any damage caused by the appliance being installed in contravention of this temperature limit will be the liability of the owner o Your new appliance is guaranteed against electrical or mechanical defects subject to certain exclusions that are noted in Baumatic s Conditions Of Guarantee The foregoing does not affect your statutory rights o The use of this appliance for any other purpose or in any other environment without the express agreement of Baumatic Ltd will invalidate any warranty or liability claim o You should not use this appliance to store items on or as a work Surface o No modifications to the appliance are permitted by Baumatic Ltd o You should not store or place flammable or highly flammable liquids materials on top of or near the appliance Items made from aluminium plastic or plastic film should also be kept away from the appliance as they may fuse to the surface o Repairs may only be carried out by Baumatic Service Engineers or their authorised service agent Child Safety o Baumatic st
11. e the hob into position Gas connection This appliance must be installed by a competent person in accordance with the current versions of the following UK United Kingdom or ROI Republic of Ireland Regulations and Safety Standards or their European Norm Replacements Important information O This cooker is supplied to run on natural gas only and cannot be used on any other type of gas without modification Conversion for use on LPG and other gases must only be undertaken by a qualified person For information on the use of other gases please contact the Baumatic Technical Department The cooker must be installed by a qualified person in accordance with the current edition of the Gas Safety Installation and Use Amendment Regulations and the relevant building l E E Regulations Failure to install the appliance correctly could invalidate Baumatic s guarantee and lead to prosecution under the regulations quoted above In the UK CORGI registered installers are authorised to undertake the installation and service work in compliance with the above regulations 17 Ventilation requirements O The room containing the cooker should have an air supply in accordance with the current edition of BS 5440 Part 2 The room must have opening windows or equivalent some rooms may also require a permanent vent If the room has a volume between 5 and 10m it will require an air vent of 50cm effective area Unless it h
12. ease note that if an engineer is asked to attend whilst the product is under guarantee and finds that the problem is not the result of an appliance fault then you may be liable for the cost of the call out charge The appliance must be accessible for the engineer to perform any necessary repair If your appliance is installed in such a way that an engineer is concerned that damage will be caused to the appliance or your kitchen then he will not complete a repair This includes situations where appliances have been tiled in sealed in with sealant have wooden obstructions placed in front of the appliance like plinths Or any installation other than the one specified by Baumatic Ltd has been completed Please refer to the conditions of guarantee that appear on the warranty card that you receive with the appliance 24 m Baumatic You will be mine United Kingdom Baumatic Ltd Baumatic Buildings 6 Bennet Road Reading Berkshire RG2 0QX United Kingdom Sales Telephone 0118 933 6900 Sales Fax 0118 931 0035 Service Telephone 0118 933 6911 Service Fax 0118 986 9124 Spares Telephone 01235 437244 Technical Advice Telephone 0118 933 6933 E mail Sales baumatic co uk technical baumatic co uk Website www baumatic co uk Republic of Ireland 01 6266 798 Czech Republic Baumatic CR spol s r o Amperova 495 46215 Librec Czech Republic 420 800 185 263 www baumatic cz Slov
13. fitting Clearances required when fitting without a cooker hood with a cooker hood 700 mm P6 SS P68SS o This appliance can be located in a kitchen a kitchen diner or a bed sitting room IMPORTANT The appliance must not be installed in a bathroom or shower room This appliance is classified as Class 3 and therefore is to be built into a kitchen unit depending on size or 600mm worktop providing the following minimum distances are allowed o The edges of the hob must be a minimum distance of 55 mm from a side or rear wall o 00 mm between the highest point of the hob surface including the burners and the underside of any horizontal surface directly above it o 400 mm between the hob surface providing that the underside of the horizontal surface is in line with the outer edge of the hob If the underside of the horizontal surface is lower than 400 mm then it must be at least 50 mm away from the outer edges of the hob o 50mm clearance around the appliance and between the hob Surface and any combustible materials 14 Unpacking the appliance When unpacking the appliance please check that the following items are contained within the packaging 1 x Baumatic hob 2 x Pan supports 4 x Burner assemblies 1 x Installation and instruction manual 1 x Baumatic guarantee card 4 x Fixing screws 4 x Clamps 1 x Sealing strip 4 x LPG jets 5 x LPG jets P68SS only 1 x Self adhesive label for amending the Gas Categ
14. isconnect the appliance from the gas and electricity supplies If a gas tap becomes stiff to operate then you should proceed as follows o Remove the control knobs pan supports burners hob fixing screws and clamps o Remove the hob from the worktop and remove any underside protective covers o Disconnect the fixings holding the tap to the fascia panel and separate the assembly Then clean the cone and seating with a cloth dampened with solvent o Lightly smear the cone with high temperature grease reassemble into position and rotate a few times o Remove the cone again and remove any excess grease making sure that the gas ducts are not obstructed with grease o Carefully reassemble the components and perform a gas soundness test If it becomes necessary to replace a gas tap then you should proceed as follows o Remove the control knobs pan supports burners hob fixing screws and clamps o Remove the hob from the worktop and remove any underside protective covers o Disconnect the fixings holding the tap to the fascia panel and separate the assembly o Disconnect the gas pipe from the gas tap then disassemble them from the gas rail by removing the fixing screws o When fitting a new tap ensure that a new gasket is used o Reconnect the gas tap perform a gas soundness test and then reassemble the hob 22 Electrical connection This appliance must be installed by a qualified person in accordance with the
15. latest edition of the E E Regulations and in compliance with Baumatic s instructions Before connecting the appliance make sure that the supply voltage marked on the rating plate corresponds with your mains supply voltage o Cable type HO5 RRF 3 core x 0 75 mm o The mains supply cable is supplied with this product Replacing the mains supply cable If the mains supply cable is damaged then it must be replaced by an appropriate replacement which can be obtained from the Baumatic Spares Department The mains supply cable should be replaced in accordance with the following instructions o Switch the appliance off at the control switch o Open the box of the supply board o Unscrew the clamp A fixing the cable o Replace the cable with one of the same length and in accordance with the specification given above o The green yellow earth wire must be connected to the terminal marked It must be about 10 mm longer than the live and neutral wires o The blue neutral wire must be connected to the terminal marked with letter N the live wire must be connected to the terminal marked with letter L 23 My appliance isn t working correctly IMPORTANT If your appliance appears not to be operating correctly then you should disconnect it from your mains supply and then contact the Baumatic Service Department on telephone number 0118 933 6911 DO NOT ATTEMPT TO REPAIR THE APPLIANCE YOURSELF Pl
16. mestic purposes only P61SS amp P62SS Product dimensions Height 500 mm Width 585 mm Depth 35 mm Aperture dimensions Height 480 mm Width 560 mm Product dimensions Height 500 mm Width 685 mm Depth 35 mm Aperture dimensions Height 480 mm Width 560 mm Product specifications O O O0 0 0909 Q 1 x 3 30 kW triple crown wok burner 2 x 1 75 kW semi rapid burners 1 x 1 00 kW auxiliary burner 1 x 3 00 kW rapid burner P68BL SS only Flame failure safety device on each burner Front control operation Heavy duty cast iron pan stands Underknob auto ignition Standard accessories o LPG Conversion jets o Wok Stand Electrical details Rated Voltage Supply Connection Max Rated Inputs Mains Supply Lead 230 Vac 50 Hz 3 A double pole switched fused outlet with 3mm contact gap 0 008 to 0 02 kW depending on model 3 core x 0 5mm Gas details Connection Rp ISO R7 Type Natural Gas 20 9 mbar alternative LPG G30 28 30 mbar town gas G110 120 8 mbar to order For future reference please record the following information which can be found on the rating plate and the date of purchase which can be found on your sales invoice The rating plate of your hob is located on the underneath of the appliance Therefore it is a good idea to record this information before you install your appliance Model Number Serial Number Date of Purchase Gas hob surface layout
17. ory on the appliance s rating plate required if the LPG conversion kit is used Installing the appliance P61SS amp P62SS P67SS amp P6sBL SS 25 mm MIN o Cut a hole in the worktop that corresponds with the drawings shown above o IMPORTANT You must have a gap of at least 25 mm between the underneath of the appliance and any surface that is below it 15 o Carefully turn the hob upside down and place it on a cushioned mat o Apply the sealing strip A provided around the edge of the appliance o The protective covering must be removed from both sides o Do not leave a gap in the sealing agent or overlap the thickness o IMPORTANT Do not use a silicon sealant to seal the appliance against the aperture This will make it difficult to remove the hob from the aperture in future particularly if it needs to be serviced A SEALING STRIP A Sealing strip B Clamp C Screw 16 O Place the clamp B over the holes that match the size of the screws There are one set of screw holes in each corner of the hob Slightly tighten a screw C through the clamp B so that the clamp is attached to the hob but so that you can still adjust the position of it Carefully turn the hob back over and then gently lower it into the aperture hole that you have cut out On the underneath of the hob adjust the clamps into a position that is suitable for your worktop Then fully tighten the screws C to secur
18. rongly recommend that babies and young children are prevented from being near to the appliance and not allowed to touch the appliance at any time During and after use all Surfaces will become hot o If it is necessary for younger family members to be in the kitchen please ensure that they are kept under close supervision at all times o Older children should only be allowed to utilise the appliance when supervised General Safety The appliance should only be installed and connected by a CORGI registered installer Care should be taken to ensure that the units and work surfaces that you build the appliance into meet with the relevant standards During use w Any film or stickers that are present on the hob surface when it is delivered should be removed before use Care should be used when utilizing the appliance otherwise there is a risk of burns being caused o You should not allow the electrical connection cables to come into contact with the hob surface when it is hot or any hot cookware o If fat and oil overheats then it can ignite extremely quickly For this reason when cooking with fat and oil the appliance should not be left unattended x Make sure that all of the cooking zones are switched off after use Cleaning o Cleaning of the hob should be carried out on a regular basis o IMPORTANT Before attempting to clean the appliance it Should be disconnected from the mains and cool o Great care sho
19. uld be taken whilst using this appliance and when following the cleaning procedure o You should not use a steam jet or any other high pressure cleaning equipment to clean the appliance Installation This appliance must be correctly installed by a CORGI registered installer strictly in accordance with the manufacturer s instructions and the relevant British Standards Please see the specific section of this booklet that refers to installation o Baumatic Ltd declines any responsibility for injury or damage to person or property as a result of improper use or installation of this appliance o If the appliance is being used in a Leisure Accommodation Vehicle the requirements of N 721 MUST be followed o Baumatic Ltd DO NOT recommend that this appliance is installed on any type of marine vessel Declaration of conformity This appliance complies with the following European Directives 73 23 EEC dated 19 02 1973 Low Voltage Directive 89 336 EEC dated 03 05 1989 EMC Directive inclusive of Amending Directive 92 31 EEC 93 68 EEC dated 22 07 1993 CE Marking Directive 89 109 EEC dated 25 01 1992 Materials that can touch food 90 396 EEC Gas Products EN60335 1 EN60335 2 EN301 1 Safety Standards The manufacturer declares that the hob is built using certified materials and requires the appliance to be installed in accordance with the standards currently in force This appliance must be used by a trained person for do
Download Pdf Manuals
Related Search