Siig USB 2.0/1394 DV Kit
Contents
1. a USB 2 0 1394 DV Kit o Quick Installation Guide Introducing the USB 2 0 1394 DV Kit The USB 2 0 1394 DV Kit is a complete DV editing kit acombo card with USB 2 0 and FireWire 1394a interfaces deluxe DV editing software full DV AVI QuickTime Windows Media RealNetworks and MPEG2 support and a 1394 6 pin 4 pin DV cable Features and Benefits e Combo card design adds four USB 2 0 480 Mbps and three 1394a 400 Mbps ports into your system e Hot swapping feature allows you to connect disconnect devices without first turning yoursystem off USB 2 0 interface e Adds three external and one internal USB 2 0 ports e Compliant with USB specification rev 2 0 e Supports high speed 480 Mbps full speed 12 Mbps and low speed 1 5 Mbps data transfer modes for simultaneous operation of multiple USB 2 0 1 1 devices Note USB 1 1 devices are limited to USB 1 1 speeds even when they are connected to USB 2 0 host adapter or USB 2 0 hubs FireWire 1394a interface e Adds two external and one internal FireWire ports 04 0288F 1 IEEE 1394 1995 P1394a rev 1 1 and OHCI Interface Specification 1 0 compliant Supports serial bus data transfer rates of 100 200 and 400 Mbps System Requirements Pentium or equivalent computer with an available PCI slot Windows 2000 SP4 XP 32 64 bit Server 2003 32 64 bit Vista 32 64 bit Recommended system for DV capturing editing Pentium 4 or abo2. chnical Support and Warranty QUESTIONS SIIG s Online Support has answers Simply visit our web site at www siig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away You can also submit questions online and a technical support analysts will promptly respond SIIG offers a lifetime manufacturer warranty with this product Please see our web site for more warranty details If you encounter any problems with this product please follow the procedures below A If it is within the store s return policy period please return the product to the store where you purchased from B If your purchase has passed the store s return policy period please follow these steps to have the product repaired or replaced Step 1 Submit your RMA request Go to www siig com click Support then RMA to submit a request to SIG RMA If the product is determined to be defective an RMA number willbe issued SIIG RMA department can also be reached at 510 413 5333 Step 2 After obtaining an RMA number ship the product Properly pack the product for shipping All software cable s and any other accessories that came with the original package must be included Clearly write your RMA number on the top of the returned package SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number poste
3. d on the outside of the shipping carton e Youare responsible for the cost of shipping Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA e SIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer About SIIG Inc Founded in 1985 SIIG Inc isa leading computer upgrade manufacturer of 1 Oconnectivity products including PCI amp ISA serialand parallel ports USB Serial ATA amp UltraATA controllers FireWire 1394a b networking sound cards and other accessories SIIG is the premier one stop source of upgrades SIIG products offer comprehensive user manuals many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall ease of installation and compatibility of our products as well as one of the lowest defective return rates in the industry SIIG products can be found in computer retail stores mail order catalogs through major distributors system integrators and VARs in the Americas and the UK and throughe commerce sites PRODUCT NAME USB 2 0 FireWire DV Kit FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 Th
4. is device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SHG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA USB 2 0 FireWire DV Kitisa trademark of SHG Inc SIIG and the SIG logo are registered trademarks of SIIG Inc Microsoft Windowsand Windows Vistaare registered trademarks of Microsoft Corporation Pentium is a registered trademark of Intel Corporation Other names used in this publication are for identification only and may be trademarks of their respective companies October 2007 Copyright 2007 by SIIG Inc All rights reserved
5. on how to properly install your DV camcorder 1 Insertthe Ulead VideoStudio DV softwareCD Auto run should start automatically If not click Start Run type in X Setup exe then click OK Change X to match your CD ROM drive letter 2 Select a language click Next and follow on screen instructions to complete installation Note For instructions on how to use Ulead VideoStudio please refer to VStudio pdf file located in the Manual directory on the Ulead VideoStudio DV software CD Connecting DV Camcorder Before setting up the digital video camcorder make sure to verify the driver for the adapter has been successfully installed in your system and follow the setup procedures listed below 1 Boot up your system 2 Connect the 4 pin connector of the provided FireWire 1394 6 pin 4 pin DV cable into your digital camcorder and connect the 6 pin connector into an available port on the 1394 adapter Power on the camcorder The camcorder should now appear in Device Manager To Verify Successful DV Camcorder Setup 1 Check Device Manager to verify successful installation Windows 2000 XP Server 2003 Right click My Computer click Manage then click Device Manager Windows Vista Right click Computer click Manage click Continue then click Device Manager Double click Imaging Device s AMicrosoftD V Camera and VCR or DVCamcorder should be displayed Blank Page Blank Page Blank Page Te
6. the slot bracket holding screw to secure the card 6 Replace the computer cover and reconnect the power cord Driver Installation Windows 2000 SP4 XP Server 2003 and Vista will detect and install the drivers automatically No additional driver is necessary To Verify Windows Installation 1 Check Device Manager to verify successful installation Windows 2000 XP Server 2003 Right click My Computer click Manage then click Device Manager Windows Vista Right click Computer click Manage click Continue then click Device Manager The drivers for this controller show up differently under different versions of Windows Please refer to the correct Windows version to verify Windows 2000 XP Server 2003 Vista a Under the Universal Serial Bus Controllers VIA USB Universal Host Controller VIA USB Universal Host Controller VIA USB Enhanced Host Controller USB Root Hub USB 2 0 Root Hub in 2000 USB Root Hub USB Root Hub b Under the IEEE 1394 Bus host controllers VIA OHCI Compliant IEEE 1394 Host Controller Ulead VideoStudio Software Installation The USB 2 0 1394 DV Kit includes Ulead VideoStudio digital video editing software for producing home videos complete with attractive titles transitions and sounds Before installing VideoStudio make sure your adapter and DV camcorder are properly installed and configured See next section Connecting DV Camcorder for more details
7. ve 512 MB RAM and CD ROM drive 5 GB of available hard disk space Package Contents USB 2 0 1394 adapter 1394 6 pin 4 pin DV cable Ulead VideoStudio DV editing software CD Quick installation guide Board Layout 1394 Ports Figure 1 Board Layout Note This power connector same as the one used with your floppy disk drive is designed to provide additional power to the board when needed This connection is optional We recommend to connect this power connector when the following conditions occur All ports are used Device s not being detected In case you need to connect this power connector power off your system first before making this connection Hardware Installation General instructions for installing the card are provided below Since the design of computer cases and motherboards vary refer to your computer s reference manual for further information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer s case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges 1 Turn OFF the power to your computer 2 Unplug the power cord and remove your computer s cover 3 Remove the slot bracket from an available PCI slot 4 Carefully align the card to the selected PCI slot push the board down firmly but gently until it is well seated 5 Replace
Download Pdf Manuals
Related Search