Recom PowerStation EVO Liquid
Contents
1. 754 939 940 478 Heat Transferring Liquid Liquid coolant used to transfer heat from the system Ready to use doesn t have to be diluted with distilled water anymore Thermal compound Used to increases heat transfer from the heat source to the cooling block Tubing Used to direct coolant around the system Fittings Used to fix hose on the liquid cooling components Installation SET UP YOUR WORK AREA Your working area should be well lit at all times gather your tools screwdriver scissors etc Installation of the CPU Block Warning Please take care while installing the CPU Block Fixing too hard using tools might cause damages to the CPU and M B 1 Please remove the retention module from the M B if necessary The M4 screws have to be put through the M B from the bottom side Please make sure that the washer and insulating is placed in between as shown on the picture 2 Please use the washer on the topside of the M B as well 3 Screw the four nuts onto the screws to fix the clip on the M B 4 Remove clear film from the base of the CPU Cooling Block and apply the thermal grease on it properly and put it onto the CPU 5 Fix the 1 4 fittings on the CPU Block hand screwed no tool needed As a last step please fix the springs and the knurled nuts included in delivery onto the screws as you can see on the next page Pump installation The pump was created for usage in a complete wate2. RECOM www recom ni Another way RECOM PowerStation Evo Liquid Case Manual Liquid Cooling Case Installation Manual Introduction The working principle of the PowerStation Evo liquid cooling case works ona method known as Heat Exchange When power is sent to the pump it begins to circulate the liquid around the system Liquid coolant is then passed through the cooling blocks which are attached to your CPU VGA amp Northbridge Chipset optional parts the liquid coolant will then transfer the heat from the heat source through the cooling blocks and then into the coolant From there the water circulates into the radiator which will then be Surface Cooled by 2 Pieces Silent 12cm 14cm optional Fans and will finally disperse the heat from the Coolant Caution Please read and understand this manual correctly and accurately before installing or operating this product By disregarding any instructions in this manual could result in damage to your computer loss of data damage to this product and or personal injury Thank you for purchasing the Recom PowersStation Evo liquid cooling product NOTICE This product is subject to updates or changes without prior notice Recom is not responsible for any direct indirect intended or unmeant damage to your computer loss of use loss of data loss of income or profit and or personal injury due to incorrect installation and illegal operation lf you do not un
3. derstand any part of this manual please contact the technical support Without understanding the instructions the installation is forbidden IMPORTANT NOTICE e Before using this liquid cooling set please read and keep the manual close by for reference e The working temperature environment of the liquid cooling set is from 10 C to 40 C e f there are any leaks from the liquid cooling system shut down your pc and unplug it and peripherals immediately and check the system carefully e Keep the radiator out of direct sunlight and away from any other heat sources e Before using the equipment please make sure that your power supply is at least 450W or more for safe operation e Hold the Molex when unplugging the power cable Plucking the power cable directly is not advised e Try not to bend or kink the tubing when using the system e Running the system with low liquid may result in damage to the parts within your computer please check the liquid every 3 months e Please screw the fittings on the components by hand no tools will be needed there is no guarantee for the damage due to this MAIN PARTS AND WORKING PRINCIPLE CPU Cooling Block Specifically designed for the heat transfer process from the CPU core Pump will provide power for the circulation of the coolant Radiator amp Fan Also know as the Heat Exchanger for dispersing heat from the coolant Mounting Plate for 1156 i5 1366 i7 LGA775 AM3 AM2
4. encountered with the operating of the liquid system please refer to the section below before contacting your point of purchase Problems The Pump does not work The cpu reports high 70 c temperatures Liquid is leaking from the pump constantly The liquid is getting low but there is no leak The pressure reducing valve fizzles The pump fizzles when the mainboard is powered but fizzles die down shortly after The heat transfer liquid is dirty amp discolored The fan of copper tube radiator doesn t work Problem Solution Check your mains power supply Check your Molex connector on the pump is fully connected to the power supply Check your Pump is working Check you have used thermal grease on the water blocks amp also check if they have been mounted properly Make sure your 120mm fan is wired up to the system power supply Check the fittings of the pumps are fixed properly Top the system up with coolant purchased from your point of purchase or distilled water This is a normal occurrence This is a normal occurrence Algae will build up in your system after time it is recommended that you replace the Liquid Coolant every 6 8 months Check to see if the power connector is connected properly If not contact your point of purchase to arrange a new fan Disclaimer Please read and understand this manual correctly and accurately before installing or operating this product By disregarding any inst
5. losing the case The installation is now completed Please check all connectors and cables before you turn on your Computer CPU Block Pump Radiator Fan Liquid Tube Fittings Material Copper base Cover Fiber Glass Nylon Dimension 50 4 x 50 4 x 9 mm Copper base total 80 5 x 104 5 x 25 mm 2x G1 4 thread Weight 175 g Compatible Sockets 1156 i5 1366 i7 478 775 939 754 AM2 AM3 Rated Voltage 12V 60 Hz Power Input 10 W Pump Speed 700 L hr Pump Height 1 7 m Life Expectancy 50000 hrs Connector 4 pin Dimension 323 x 142 x 29 mm Material Brass Copper Fins with 2x G1 4 thread Weight 710 g Dimension 120x120x25 mm Rated Voltage 12V Power Input 2W Speed 1000 RPM Life Expectancy 50000 hrs Connector 3 pin Ingredients Distilled Water Glycol UV liquid etc Ready to use Volume 500 ml Anti corrosive fluid for PC liquid cooling systems Protects copper aluminium brass and nickel Injurious to health when swallowing Keep out of the reach of children Avoid contact with the eyes and skin Material PUR or PVC 8 10 Length 2m Diameter ID 8 mm OD 10 mm Material Plated Brass for 1 4 thread for tube 8 10 This product is subject to updates or changes without prior notice Please check for update informations and optional add on components at www recom nl in order to extend your water cooling kit TROUBLESHOOTING If any trouble is
6. lowed Step 1 From Pump OUT to CPU Block Step 2 From CPU Block to Radiator Step 3 From Radiator to Pump IN It is sufficient to fix hand screwed only Filling up the Cooling Systeme amp Testing Pump To fill up the water cooling kit you need the funnel or syringe the coolant and a screwdriver The coolant is ready to use and doesn t have to be mixed anymore with destilled water Step 1 Please remove the 220 Volt plug from your PC Step 2 Remove the 20 24 PIN power plug of the PSU from your M B It is best to remove other components like HDD from power as well Step 3 Bypass the power plug by connecting the green wire with the black one using a paper clip for example This step prevents the M B for getting electricity but it is still possible to switch the pump on and off using the power button at the PSU You also can use the Recom T8 or T12 PSU power tester Step 4 Please open the screw at the top of the pump to fill up fill in some coolant into the pump using a small funnel Switch on the ATX PSU and fill the pump step for step Step 5 Initial noises from the pump are quite normal and will stop after filling up the system completely If there are problems with the circulation of the coolant please shake the pump carefully Step 6 In order to get out the air bubbles inside the radiator you need to shake the radiator gently as well Please test the pump for a minimum of 1 2 hours before c
7. r cooling system only please take care on the coolant level If it is too low the pump might be damaged Pump is preinstalled on the bottom of the case please take care on IN and OUT connector while installing the hose Filling cavity Outtake Please connect the pump directly to the Power Supply Unit with the 4 pin molex connector The pump can be moved for mounting The current location is a suggested location In some cases it can be possible the pump needs be moved a few centimetres because of mainboard Space mounting The mounting screws are located on the bottom outer side of the case CAUTION The Liquid level in the pump reservoir needs to be higher then the end of the pipe inside the reservoir that is connected to the intake Lower can cause damage to the pump and exceeds the warranty Check the reservoir liquid level regularly Radiator Fitting Installation Screw the two 1 4 fittings into G1 4 thread of the pre mounted radiator by hand now you can connect this radiator with other components by using enclosed tube Tubing Installation After installing the CPU Block it is time to connect the single components to each other Please trim the tubes due to your personal system It is important to straight cut the ends of the tubes A side cutter is recommended to do so The tubes will be connected with the included 1 4 fittings The single steps to connect the single components as fol
8. ructions of this manual could result in damage to your computer loss of data damage to this product or personal injury Recom will not be held responsible for any of the above and in proper use of this piece of equipment All trademarks are registered to their respective owners Manual v1 1
Download Pdf Manuals
Related Search