Atdec VF-AT-NP
Contents
1. Step 6 Cable Management Ensure Arm is fully extended IMPORTANT VF AT NP Installation Instructions The User Operating Card must be left with q av g P 5 a a Ve Visidec Focus Articulated Arm once installed Focus Notebook Mount AT E A I ee A Route the Cables underneath the Arms inserting the Primary and Secondary Arm Cable Covers to hold the Cables in place Component Checklist TIP Leave enough slack in the cables i Desk Clam lt gt at the joints to allow full movement 7 a a ini AS _ wont C aA Pressure M8 Desk 5mm Allen Desk Clamp Plate Clamp Screw Key Bracket Hardware se l Notebook Tray and see ie C Insert cables into Arm Assembly lt pa w r a ook and Loop A pies me Insert Secondary Pole Top Primary Arm Fasteners x4 sets ee Arm Cable Cover P ania in place a a sae m _ crew Insert Primary Bolt Through Sacandany Aum Arm Cable Cover Base Cable Cover TOOLS REQUIRED O Cable e Power Drill Ca d Balls x2 O TIP If the Visidec Focus 9mm 3 3 Drill Bit Steel Washer Cable Balls x2 Cable Clip Arm is to be used in a ee ee okt IMPORTANT INFORMATION Clip to secure the cables IMPORTANT Install Visidec Focus Notebook Mount as per Installation Instructions to the Pole Visidec Focus Notebook Mount supports Notebooks up to 18 weighi2. ap into G Insert the 5mm Allen Key into the top of the Visidec Pole the slot in the Pole Top Cap _D Slide the Arm Assembly and the Handgrip down the Visidec Pole E Lock the Handgrip
3. ng up to 8kg 17 lbs This product is designed to be used in conjunction with an external keyboard and mouse The Manufacturer accepts no responsibility for incorrect installation To insert Cable Covers Step 1 Check Components Check you have received all parts against the Component Checklist and Hardware above Step 2 Desk Mounting Bolt Through or Desk Clamp Option A Bolt Through Pole Assembly A Insert tabs Drill a 9mm hole in the Work ee Surtace at the desired position and ase assemble as shown Work Surface rear edge Q gt Steel Washer Your Visidec Focus Notebook Mount installation is complete and ready for use the Pole Assembly be mounted M8 Desk Clamp Screw o towards the rear edge of the found in the Desk atdec Work Surface 5mm Allen Key VY Clamp Box Tighten Firmly Due to continuing product development the manufacturer reserves the right to alter specifications without notice Published 22 04 09 9mm 3 Hole _ Installation Complete NOTE It is recommended that Step 2 Desk Mounting Bolt Through or Desk Clamp i Install the M8 Desk Clamp Screw OPONE a Desk Clamp and Pressure Plate as shown Step 4 Install the Notebook Computer Adjust the height of the Pressure Plate to suit the Work Surface and Tighten Firmly in desired location to suit the width of your Notebook Computer PAANAN S
4. upport Tabs do not obstruct any cable ports Attach the Desk Clamp Bracket to the bottom of the Pole Assembly using the M8x30mm Screw Tighten Firmly A Adjust the Support Tabs qye Work Surface Notebook Computer Desk Clamp Bracket 5mm Allen Key B To increase stability use the Self Adhesive Hook and Loop Fasteners supplied M8x30mm Pressure Plate e Peel off the backing paper from the Fasteners e Attach Fasteners to your Notebook Computer and the Notebook Tray DMD Sa ly Clamp Screw Sx 5mm Assembly SS Allen Key Step 3 Attach the Arm Assembly onto the Pole Assembly ee a e Ensure that each set of Fasteners are oo reer et correctly aligned i e Hook to Loop Dab Surtaces A abs x z Fasteners Hook x4 C Position your Notebook Computer Fasteners Loop x4 j onto the Notebook Tray A Unlock the Handgrip Handgrip Tab Step 5 Connect Cables Handgrip Connect cables to your Notebook Computer Lift the Cable Management Clip on the back of the Arm Assembly Notebook Tray and route the Cables underneath Release the Clip to hold the Cables in place Notebook B Slide Handgrip to the A l Cables _ A B t top of the Visidec Pole so v C Slip the Arm Assembly over omputer Cable the Handgrip Tab and then onto the Handgrip Tab protrudes ha Wieidac Pale Management Clip eaves F Insert the Pole Top C
Download Pdf Manuals
Related Search