Atdec VF-AT-D flat panel desk mount
Contents
1. Allen Ke Pole Assembly Step 3 ADUSTMENT AN6 Suits 12mm to 38mm 1 thick work surfaces NOTE It is recommended that the Pole Assembly be clamped to the rear or side edge of the work surface Step 2 Install the M8 Desk Clamp Screw and Pressure Plate as shown Pressure Plate M8 Desk Clamp Screw 5mm Allen Key Adjust the height of the Pressure Plate to suit the Work Surface and tighten firmly in the desired location Assembly Work Surface 5mm Allen Key lt Tighten Firmly C Assemble the Double Arm Assembly onto the Pole Assembly Handgrip Step 1 KI Unlock the K handgrip Handgrip Tab Step 2 Lift the handgrip to the top of the pole so that the Handgrip Tab protrudes Slide the Double Arm Assembly and the Handgrip down the Pole For Displays with 75mm x 75mm 3 x 3 mounting hole patterns M4 Display Mounting Screws For Displays with 100mm x 100mm 4 x 4 mounting hole patterns Lock the Handgrip a A Step 2 Insert a Secondary Arm Cable Cover Step 1 Connect cables NOTE If Visidec Focus Articulated Arm Double is to be used in a multi user evironment do not install the Cable Balls and only use the Cable Clips Double Arm Assembly Step 3 Slip the Double Arm Assembly over the Handgrip Tab and then onto the Pole Step 6 Step 7 Insert the Pole Insert the 5mm Allen Top Cap into Key into the slot in Pole Top2. Cap the Pole the Pole Top Cap NOTE Leave enough slack in the cables to allow for movement Step 3 Insert Primary Arm Cable Cover Step 4 Insert cables into slot using cable balls to hold them in place single user only and then u see note p Cable gt Balls x2 Step 5 Attach remaining cables that do not fit into the slot with the two supplied cable clips F Leave the User Operating Card with Visidec Focus Articulated Arm Double Leave the User O perating Card secured to the base of Visidec Focus Articulated Arm Double with the atdec logo facing upwards La atdec No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd Due to continuing product development the manufacturer reserves the right to alter specifications without notice Published 13 02 08
3. IM PO RANT The User O perating Card must be left with Visidec Focus Articulated Arm Double once installed User O perating Card see note at top of page B1 Bolt Through Drill a 9mm hole in the work surface at the desired position and assemble as shown below Slot Pole Assembly Bolt Through Base 9mm Hole Steel washer M8 Desk Clamp Scre found in the Desk Clamp Box 5mm Allen Key Tighten Firmly NO TE Ensure the slot in the Pole Assembly faces away from the user It is recommended that the Pole Assembly be mounted towards the rear edge of the work surface Installation Primary Arm Cable Cover x2 M8x30mm Screw Pole Top Cap SS a g Tea tsk ps Bolt Through Base Secondary Arm Cabl Cable Cover x2 saa Balls x2 B2 Desk Clamp Instructions Pressure Plate Clamp Screw Display Mounting Screws i M4x10mm Cable Clip x2 x8 M4x1l2mm x8 pea M4xl6mm Steel x8 Washer NOTE When using the Desk Clamp mounting option the displays can only be used in side by side configuration as shown Failure to do so may result in serious damage to product and displays Step 1 Attach the Desk Clamp Bracket to the bottom of the Pole Assembly using the M8x30mm Screw Tighten firmly using the 5mm Allen Key Ensure the Visidec logo is facing the front as shown Desk Clamp Bracket Tighten M8x30mm Screw Bolt Thru Base
Download Pdf Manuals
Related Search