CyberPower OR1500LCDRM1U uninterruptible power supply (UPS)
Contents
1. CyberPower Reliability Quality Value Office Rack Mount UPS OR1000LCDRM1U OR1500LCDRM1U User s Manual K01 0000053 00 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries Please read and follow all instructions carefully during installation and operation of the unit Read this manual thoroughly before attempting to unpack install or operate CAUTION The UPS must be connected to a grounded AC power outlet with fuse or circuit breaker protection DO NOT plug the UPS into an outlet that is not grounded If you need to de energize this equipment turn off and unplug the UPS CAUTION DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT CyberPower Systems does not sell products for life support or medical applications DO NOT use in any circumstance that would affect the operation or safety of any life support equipment with any medical applications or patient care CAUTION The battery can energize hazardous live parts inside even when the AC input power is disconnected CAUTION To prevent the risk of fire or electric shock install in a temperature and humidity controlled indoor area free of conductive contaminants Please see specifications for acceptable temperature and humidity range CAUTION To reduce the risk of electric shock do not remove the cover except to service the battery2. same On average utility power operates 88 of the time and the CyberPower GreenPower Technology will work in its money energy saving Bypass Mode Limited Warranty and Connected Equipment Guarantee In purchasing an OR1000LCDRM1U OR1500LCDRM1U in the United States or Canada the original end user receives a Limited Warranty and CyberPower s Power Control Guarantee from Cyber Power Systems USA Inc for ease of reading referred to as CyberPower The Limited Warranty and the Power Control Guarantee are intended to be the original end user s exclusive rights and remedies The Limited Warranty and the Power Control Guarantee are separate all though they are related The Limited Warranty is for the Product itself The Power Control Guaranty is CyberPower s connected equipment guaranty Limited Warranty The original end user referred to as the Initial Customer receives an express limited warranty referred to as the Limited Warranty for the OR1000LCDRM1U OR1500LCDRM1U purchased from CyberPower referred to as the Product The terms of the Limited Warranty are explained below Power Control Guarantee CyberPower provides the Initial Customer with protection in the event that the Product is not free from defects in materials and workmanship and certain equipment connected to the Product is damaged the Power Control Guarantee The Power Control Guarantee protects the Initial Customer for damage to equipment pl
3. if CyberPower is unable to or decides not to repair or replace the Product if defective within a reasonable time CyberPower will refund to you the full purchase price you paid for the Product purchase receipt showing price paid is required POWER CONTROL GUARANTEE If you are the Initial Purchaser the Power Control Guarantee provides protection for damage to equipment connected to the Product Connected Equipment subject to certain terms and limitations The Power Control Guarantee is not first dollar coverage CyberPower s obligation is reduced by any amounts that Initial Customer is entitled to recover from other sources regarding the Connected Equipment including insurance other warranty or extended warranty coverage whether or not the Initial Customer makes a claim for recovery including but not limited to a claim under any applicable insurance other warranty or extended warranty The Limited Warranty does not cover Connected Equipment but as is explained below to be covered under the Power Control Guarantee the Connected Equipment must have been damaged due to a failure of the Product The Connected Equipment must have been damaged due to a defect in materials or workmanship of the Product In the event of damage to the Connected Equipment your exclusive remedy and CyberPower s sole obligations are as follows for Connected Equipment If a the Product purchased and owned by you is defective in material or workmanship b
4. lt lt e power may be damaging to important data files but with Automatic Voltage Regulation the computer will not experience damaging voltage levels An Automatic Voltage Regulator automatically increases low or decreases high voltage to a consistent computer safe 110V 120V The units powerful sealed lead acid batteries will provide power only if the incoming voltage drops below 90V or increases above 140V HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT 1 Make sure that the total Volt Amp VA requirements of your computer monitor and peripheral equipment does not exceed 1000 VA 1500VA 2 Ensure that the equipment plugged into the four battery power supplied surge outlets does not exceed the UPS unit s rated capacity 1000VA 600W for OR1000LCDRM1U 1500VA 900W for OR1500LCDRM1U If the rated unit capacities are exceeded an overload condition may occur and cause the UPS unit to shut down and the circuit breaker to trip 3 If the power requirements of your equipment are listed in units other than Volt Amps VA convert Watts W or Amps A into VA by performing the calculations below Note The equation listed below only calculates the maximum amount of VA that the equipment can use not what is typically used by the equipment at given time Users should expect usage requirements to be approximately 60 of the maximum power requirements Watts W x 1 67 VA or Amps A x 120 VA Add the totals up for all
5. Amount Making a Power Control Guarantee Claim To make a Warranty claim for damage to Connected Equipment under the Power Control Guarantee you must do the following 1 Complete and return the CyberPower Warranty card or provide reasonable proof of purchase for example a sales receipt that establishes you as the original end user consumer purchaser of the Product 2 Call CyberPower at 952 403 9500 or 877 297 6937 toll free write to CyberPower at 4241 12th Ave East Suite 400 Shakopee MN 55379 or e mail CyberPower at clains cyberpowersystems com within ten 10 days of the date of the event for which you wish to make a claim for warranty service 3 When you contact CyberPower identify the Product the Purchase Date and the item s of Connected Equipment Have information on all applicable insurance or other resources of recovery payment that are available to the Initial Customer and the name of the power utility supplier for the location of the Connected Equipment and Request a Return Materials Authorization RMA 4 Pack and ship the product to CyberPower and if requested the item s of Connected Equipment a repair cost estimate for the damage to the Connected Equipment and all claim forms that CyberPower provides to you Show the RMA number on the shipping label or include it with the product You must prepay all shipping costs must pay the cost of the repair estimate and is responsible for packaging and shipment CyberPower
6. s of all payment you have or are entitled to receive from insurance other warranties extended warranties or from other sources or persons for the Connected Equipment or damage to such equipment so that CyberPowerj s maximum liability shall be reduced to reflect all such other payments or sources of recovery If CyberPower replaces the connected equipment or pays to the Initial Customer the Agreed Damage Amount the Initial Customer shall transfer all item s to CyberPower without warranty by the Initial Customer but free of lien or other interest CONDITIONS COMMON TO THE LIMITED WARRANTY AND THE POWER CONTROL GUARANTEE The Limited Warranty and the Power Control Guarantee are the only and the exclusive express warranty of CyberPower with respect to the Product This exclusion of other express warranties applies to written and oral express warranties LIMITATION THE LIMITED WARRANTY AND THE POWER CONTROL GUARANTEE DO NOT COVER The Limited Warranty and the Power Control Guarantee are intended to exclusive rights and remedies and replace any other rights to the extent allowed by law 1 As to the CyberPower Product the limited warranty does not cover or apply to misuse modification operation or storage outside environmental limits for the Products in transit in shipment or in storage damage or deterioration improper operation or maintenance or use with items or equipment not designed or intended for use with the product 2 As to Conne
7. There are no user serviceable parts inside except for the battery CAUTION To avoid electrical shock turn off the unit and unplug it from the AC power source before servicing the battery or installing a computer component CAUTION DO NOT USE WITH OR NEAR AQUARIUMS To reduce the risk of fire do not use with or near aquariums Condensation from the aquarium can come in contact with metal electrical contacts and cause the machine to short out CAUTION DO NOT USE WITH LASER PRINTERS The power demands of laser printers are too large for a UPS INSTALLING YOUR UPS SYSTEM INSPECTION The box should contain the following 1 PowerPanel Business Edition software CD 1 RS232 cable DB 9 1 USB cable A B type 1 Telephone communication cable 1 user manual 1 Warranty registration card 1 UPS unit 2 Rack mount rails 5 2 Rack mount brackets OVERVIEW The OR1000LCDRM1U OR1500LCDRM1U provides automatic voltage regulation for inconsistent utility power The OR1000LCDRM1U OR1500LCDRM1U features 1030 Joules of surge protection and provides battery backup during power outages The OR1000LCDRM1U OR1500LCDRM1U ensures consistent power to your computer system and its included software will automatically save your open files and shutdown your computer system during a utility power loss AUTOMATIC VOLTAGE REGULATOR AFE POW The OR1000LCDRM1U OR1500LCDRM1U stabilizes inconsistent utility power The incoming utility
8. cator light will illuminate and the unit will beep once 7 If an overload is detected an audible alarm will sound and the unit will emit one long beep To correct this turn the UPS off and unplug at least one piece of equipment from the battery power supplied outlets Wait 10 seconds Make sure the circuit breaker is depressed and then turn the UPS on 8 Your UPS is equipped with an auto charge feature When the UPS is plugged into an AC outlet the battery will automatically recharge 9 To maintain optimal battery charge leave the UPS plugged into an AC outlet at all times 10 To store your UPS for an extended period cover it and store with the battery fully charged Recharge the battery every three months to ensure battery life BATTERY REPLACEMENT CAUTION Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery Service the battery under the supervision of personnel knowledgeable of batteries and their precautions CAUTION Use only the specified type of battery See your dealer for replacement batteries CAUTION The battery may present the risk of electrical shock Do not dispose of batteries in a fire as they may explode Follow all local ordinances regarding proper disposal of batteries CAUTION Do not open or mutilate the batteries Released electrolyte is harmful to the skin and eyes and may be toxic CAUTION A battery can present a high risk of short circuit current and electrical shock Take the follo
9. cted Equipment the Power Control Guarantee covers only damage within the specific terms of the Power Control Guarantee to Connected Equipment and only up to the applicable aggregate ceiling amount 3 The Power Control Guarantee does not cover damage to Connected Equipment or apply if the Product has been operated in a failure mode or not in compliance with CyberPower operating instructions and manuals or if the Connected Equipment has been operated in a failure mode or not in compliance with the instructions and manuals of its manufacturer vendor The Limited Warranty and the Power Control Guarantee Do Not Apply Unless The Initial Customer 1 Has properly connected the Product and the Connected Equipment to properly wired and grounded outlets including compliance with electrical and safety codes of the most current electrical code ANS NFPA 70 without the use of any adapters extension cords of other connectors 2 Has provided a suitable and proper environment for use and installation of the Product and Connected Equipment 3 Has properly installed and operated the CyberPower Product and Connected equipment 4 Has operated the Product at all times within the limitations on the Productjjs VA capacity as stated in this User Manual CyberPower Does Not Cover or Undertake Any Liability in Any Event for Any of the Following 1 Loss of or damage to data records or software or the restoration of data or records or the reinstallation of softwar
10. e 2 Damage from causes other than AC Power Line Transients spikes or surges on properly installed grounded and code compliant 120 volt power lines in the United States and Canada transients surges or spikes on standard telephone land lines PBX telephone equipment lines or ethernet lines when properly installed and connected 3 Damage from any circumstance described as excluded above with respect to the product 4 Damages from fire flood wind rain rising water leakage or breakage of plumbing abuse misuse or alteration of either the product or the Connected Equipment Exclusion of Consequential and Other Damages The sole and exclusive remedies of the Initial Customer are those provided by the Limited Warranty and Power Control Guarantee CyberPower excludes any liability for personal injury under the Limited Warranty and Power Control Guarantee CyberPower excludes any liability for direct indirect special incidental or consequential damages whether for damage to or loss of property EXCEPT FOR AND ONLY FOR the specific limited agreement of CYBERPOWER to provide certain warranty benefits regarding Connected Equipment under the CYBERPOWER Power Control Guarantee loss of profits business interruption loss of information or data This exclusion applies even though damage or loss is caused by negligence or other fault NOTE Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages
11. es Dry contact Yes Line Conditioning Regulation RJ11 RJ45 One In One Out Windows 2000 XP Vista EXPECTED RUNTIME IN MINUTES OR1000LCDRM1U OR1500LCDRM1U iMac G4 100 110 155 170 Desktop PC with 17 LCD Monitor 71 80 88 100 Desktop PC with 19 LCD Monitor 54 62 65 75 Desktop PC with 21 LCD Monitor 35 42 49 58 Desktop PC with 17 CRT Monitor 32 38 40 48 CYBERPOWER GREENPOWER UPS TECHNOLOGY Our new UPS circuit is designed to save energy operating in GreenPower Bypass Mode A traditional UPS circuit with AVR provides normal output voltage through the Relay and AVR transformer The current travels first through the transformer conducting energy and generating heat This heat creates energy dissipation resulting in a Power Loss or consumption of utility power and money CyberPower s GreenPower Circuit Design is a solution to this Power Loss When the Utility Power is operating normally our Green Power UPS works in Bypass Mode Our GreenPower design conducts power only through the Relay and still provides normal output voltage Bypassing the transformer reduces power consumption ENERGY SAVING thereby conserving energy and saving money When the utility power is abnormal the UPS will operate under TECHNOLOGY Battery or AVR Mode Under this condition Green Power UPS and a traditional UPS would operate about the
12. ll be required to provide proof of purchase as described below to have the benefits of this Limited Warranty LIMITED WARRANTY CyberPower warrants to you the Initial Purchaser that the Product will be free from defects in material and workmanship for three years from the date of original purchase subject to the terms of this Limited Warranty This Limited Warranty gives you specific rights and you may have other rights which vary from State to State or Province to Province Any Implied Warranty of Merchantability or for Fitness for a Particular Purpose if applicable to the Product is limited in duration to the period of ownership by the Initial Customer This provision shall NOT create any Implied Warranty or Merchantability or of Fitness for a Particular Purpose that would not otherwise apply to the Product NOTE Some States and some Provinces do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you To be covered you must still be the owner of the Product at the time of the failure that results in the claim made under this Limited Warranty Exclusive Remedies Under Limited Warranty Your exclusive remedy and CyberPower s sole obligations are as follows for the Product If a the CyberPower Product you purchased and still own is defective in material or workmanship under this Limited Warranty or any applicable warranty imposed by law and b all Limited Warranty requirements have bee
13. n met CyberPower will repair or replace the Product if it proves to be defective in material or workmanship during the Warranty Period Making a Limited Warranty Claim To make a Limited Warranty claim on a Product you must do the following 1 Complete and return the CyberPower Warranty Registration Card or provide reasonable proof of purchase for example a sales receipt that establishes you as the Initial Customer the original end user consumer purchaser of the Product and prove that the Product was purchased within three 3 years of the event for which you want to make a claim for warranty service 2 Call CyberPower at 952 403 9500 or 877 297 6937 toll free write to CyberPower at 4241 12th Ave East Suite 400 Shakopee MN 55379 or e mail CyberPower at claims cyberpowersystems com within ten 10 days of the event for which you want to make a claim 3 When you contact CyberPower identify the Product the Purchase Date and request Return Materials Authorization RMA information from CyberPower 4 Pack and ship the Product to CyberPower as instructed in your RMA Show the RMA code on the shipping label or include it with the Product You MUST prepay all shipping costs and you are responsible for packaging and shipment CyberPower will inspect and examine the Product within ten 10 days of receipt If the Product is not as warranted CyberPower will repair or replace the Product and return it to you at CyberPower s expense or
14. nel Business Edition software This interface is also compatible with the UPS application provided by Windows Vista and Mac OS X 9 Dry contact This port produces information for equipment that can read dry contact signals 10 Circuit Breaker Located on the side of the UPS the circuit breaker serves to provide overload and fault protection Under normal operating conditions the circuit breaker is depressed 11 Electrical Wiring Fault Indicator This LED indicator will illuminate to warn the user that a wiring problem exists such as bad ground missed ground or reversed wiring If this is illuminated disconnect all electrical equipment from the outlet and have an electrician check to ensure the outlet is properly wired 12 AC Input Connect the AC Power cord to a properly wired and grounded outlet 13 Expansion Port Allow users to add the optional SNMP card Hardware Installation Guide 1 Your new UPS may be used immediately upon receipt However recharging the battery for at least four hours is recommended to ensure that the battery s maximum charge capacity is achieved Charge loss may occur during shipping and storage To recharge the battery simply leave the unit plugged into an AC outlet The unit will charge in both the on and off position 2 If you will use the software connect the USB cable to the USB port on the UPS 3 With the UPS unit off and unplugged connect the computer monitor and any externally powered data st
15. orage device Zip drive Jazz drive Tape drive etc into the battery power supplied outlets DO NOT plug a laser printer copier space heater vacuum paper shredder or other large electrical device into the UPS The power demands of these devices will overload and possibly damage the unit 4 To protect a fax telephone modem line or network cable connect a telephone cable or network cable from the wall jack outlet to the IN jack of the UPS Then connect a telephone cable or network cable from the OUT jack on the UPS to the modem computer telephone fax machine or network device 5 Plug the UPS into a 2 pole 3 wire grounded receptacle wall outlet Make sure the wall branch outlet is protected by a fuse or circuit breaker and does not service equipment with large electrical demands e g air conditioner refrigerator copier etc Avoid using extension cords If used the extension cord must be grounded and rated for 15 amps 10 A 6 Depress the power switch to turn the unit on The power on indi
16. pieces of equipment and multiply this total by 0 6 to calculate the approximate requirements There are many factors that can affect the amount of power that your computer system will require The suggested total load that you will be placing on the battery powered outlets should not exceed 80 of the unit s capacity BASIC OPERATION DESCRIPTION 1 LCD module display LCD shows all the UPS information with icons and messages Ss ae 2 Power On Indicator This LED is illuminated when the utility condition is normal and the UPS outlets are providing power free of surges and spikes 3 Power Switch a Master on off switch for equipment connected to the be battery power supplied outlets 4 LCD function selected switch The switch can be used to select the LCD display contents Including input output voltage and estimated run time etc 5 Battery Surge and AVR Outlets Provides four battery power surge protected and AVR outlets for connected equipment and ensures temporary uninterrupted operation of your equipment during a power failure 6 Surge Outlets Provides two surge protected outlets for connected equipment 7 Communication Protection Ports RJ11 RJ45 Communication protection ports will protect any standard modem fax telephone line or network cable 8 USB Port to PC This port allows connection and communication from the USB port on the computer to the UPS unit The UPS communicates its status to the PowerPa
17. problem tech cyberpowersystems com The USB cable is not Connect the USB cable to the UPS unit and an open connected USB port on the back of the computer PowerPanel Business Edition is inactive The unit is not providing Shutdown your computer and turn the UPS off Wait 10 battery power seconds and turn the UPS on This should reset the unit Additional troubleshooting information can be found at www cyberpowersystems com support htm TECHNICAL SPECIFICATIONS Model OR1000LCDRM1U OR1500LCDRM1U Capacity 1000VA 600W 1500VA 900W Input Voltage on Utility 90V to 140V Input Frequency 57 Hz to 63 Hz AVR Max boost 12 of input voltage for output regulation while input voltage is from 16 to 25 under nominal On Battery Output Voltage 120Vac 5 On Battery Output Wave Form Simulated Sine Wave Form Transfer Time 4ms Typical Overload Protection Yes Lightning Surge Protection Yes Internet Ready DSL Phone Fax Modem Protection Operating Temperature 32 F to 104 F 0 C to 40 C Maximum Dimensions cm 1U Rack 43 3 x 39 5 x 4 4 1U Rack 43 3 x 49 0 x 4 4 Weight kg 16 1 19 4 Typical Battery Recharge Time 8 hours typical from total discharge Battery Type Sealed Maintenance 6V 7 0AH x4 6V 9 0AH x 4 Free Lead Acid Battery Indicators Power On Wiring Fault Audible Alarms On battery Low battery Overload PowerPanel Business Editon Software Self Test Yes Auto Charge Yes Auto Restart Yes USB Y
18. r is the warrantor under this Limited Warranty You may also contact CyberPower on the Internet at www cpsww com
19. s Duties CyberPower will inspect and examine the Product and the item s of Connected Equipment or at CyberPower s election your written statement and repair cost estimate for those item s You must return the product for inspection If the damage to Connected Equipment is covered by the Power Control Guarantee CyberPower will in addition to Limited Warranty remedies for the CyberPower Product itself repair or pay the costs of repair or replace the Connected Equipment or at the option of CyberPower as permitted by law pay to the Initial Customer the Agreed Damage Amount up to the aggregate limits stated below for all item s of Initial Customer s Connected Equipment The Agreed Damage Amount for all items of Initial Customer s Connected Equipment shall be the lesser of the amount determined under Clause 1 or 2 below reduced by any amounts described in Clause 3 below 1 The fair market value of the Connected Equipment as established by the lower of a the average price the same or similar items are being sold for on E bay b the price list of Orion Blue Book on the date of occurrence or if such price list is no longer published a published or announced price list reasonably selected by CyberPower or c the lowest price the same or similar items can be purchased for in the United States 2 The aggregate ceiling amount for all Connected Equipment CyberPower OR1000LCDRM1U 175 000 OR1500LCDRM1U 200 000 3 The amount
20. so the above limitation may not apply to you DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT OR OTHER HIGH RISK ACTIVITIES CyberPower does not sell the Products for use in high risk activities The Product is not designed or intended for use in hazardous environments requiring fail safe performance including the operation of nuclear facilities aircraft navigation or communication systems air traffic control weapons systems life support or medical applications or for use in any circumstance in which the failure of the Product could lead directly to death personal injury or severe physical or property damage or that would affect operation or safety of any medical or life support device collectively High Risk Activities CyberPower expressly disclaims any express or implied warranty of fitness for purpose for High Risk Activities CyberPower does not authorize use of any of its products in any High Risk Activity ANY SUCH USE IS IMPROPER AND IS A MISUSE OF A CYBERPOWER PRODUCT The Limited Warranty and the Power Control Guarantee are governed by the laws of the United States and the State of Minnesota without reference to conflict of law principles The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded Contact Information CyberPower s address is 4241 12th Ave East Suite 400 Shakopee MN 55379 and its phone number is 952 403 9500 or 877 297 6937 toll free CyberPowe
21. ss gt 3sec Sound Disable Press gt 3sec again Sound Enable Overload V Illuminated X Not Illuminated Either Battery mode Capacity Display Digital Value Display Select SW Press Load Battery Input Output Run of Cap Cap Voltage Voltage Time Load Initial X V V 1st 2nd 3rd Ath Sth Return Press gt 3sec Sound Disable Press gt 3sec again Sound Enable Overload V Illuminated X Not Illuminated Either TROUBLE SHOOTING Full time surge protection a Turn the UPS off and unplug at least one piece of equipment outlets stop providing power CITCUIL breaker has tipped Wait 10 seconds reset the circuit breaker by depressing the due to an overload to equipment button and then turn the UPS on Battery not fully charged Recharge the battery by leaving the UPS plugged in The UPS does not provide expected runtime Baien iah wom oul Contact CyberPower Systems about replacement batteries at Y an tech cyberpowersystems com The on off switch is designed to prevent damage by rapidly Turn the UPS off Wait 10 seconds and then turn the UPS on turning it off and on The UPS will not turn on Contact CyberPower Systems about replacement batteries at The Palen tS worn out tech cyberpowersystems com Contact CyberPower Systems at Mechanical
22. the Limited Warranty requirements have been met except that the three year limitation of the Limited Warranty does not limit the Power Control Guarantee which is for the lifetime of the Product and c none of the limitations or exclusions on warranty coverage apply or than the three year limit CyberPower will as CyberPower elects as permitted by law repair replace or pay the Agreed Damage Amount defined below for the item s of your electronic equipment directly and properly connected to the product the Connected Equipment if that Connected Equipment is x damaged by AC power line transients spikes or surges on properly installed grounded and code compliant 120 volt power lines in the United States and Canada or by transients surges or spikes on standard telephone equipment lines or Base 10 100T Ethernet lines that are properly installed and connected a Power Disturbance and y is directly plugged into and properly connected to a CyberPower Product in its original condition which is properly operated when a Power Disturbance passes through the CyberPower Product and y 1 exhausts the protection capacity of the CyberPower Product or y 2 damages the CyberPower Product This provision sets out the only liability of any character of CyberPower for direct indirect special consequential and or incidental damages under our Limited Warranty applies only to Connected Equipment and all such Liability is limited to the Agreed Damage
23. ugged into the Product The terms of the Power Control Guarantee are explained below The Limited Warranty and the Power Control Guarantee are subject to the terms set forth below Additionally State or Provincial law may adjust the terms of the Limited Warranty or the Power Control Guarantee or the State or Province may impose additional obligations or additional implied warranties To the extent necessary to comply with those laws the terms of the Limited Warranty and the Power Control Guarantee should be read to adjust to those requirements only to the extent necessary to comply with such local law If you are an Initial Customer you are asked to read the following terms and conditions carefully before using the Product By using the Product you consent to be bound by and become a party to the Limited Warranty and Power Control Guarantee If you do not agree to the terms and conditions of the Limited Warranty and Power Control Guarantee you should return the Product for a full refund prior to using it REGISTRATION CyberPower requests that you complete and return the Warranty Registration Card enclosed with the Product or register the Product at its website www cpsww com to establish that you are the Initial Customer of the Product and therefore entitled coverage under the Limited Warranty and the Power Control Guarantee Registration is not required for Limited Warranty coverage but note if you do not complete a registration card you wi
24. wing precautions before replacing the battery 1 Remove all watches rings or other metal objects 2 Only use tools with insulated handles 3 DO NOT lay tools or other metal parts on top of battery or any battery terminals 4 Wear rubber gloves and boots 5 Determine if the battery is inadvertently grounded If inadvertently grounded remove source of ground CONTACT WITH A GROUNDED BATTERY CAN RESULT IN ELECTRICAL SHOCK The likelihood of such shock will be reduced if such grounds are removed during installation and maintenance applicable to a UPS and a remote battery supply not having a grounded circuit BATTERY REPLACEMENT PROCEDURE 2 Remove the three retaining screws on the cable protection cover then remove the cover 3 Disconnect the black and red cable 1 Remove the right side of the faceplate 5 Replace the new battery pack Assemble the screws cover cable and front panel in the reverse sequence of above steps Recharge the unit for 4 8 hours to ensure the UPS performs expected runtime 4 Remove the retaining screw of the cable connectors DEFINITIONS FOR ILLUMINATED LCD INDICATORS LOAD BATT CAP INPUT OUTPUT RUN_TIME oe A K 6 Dy Q 100 K A Baal Bal Dal UPS Status Display Capacity Display Digital Value Display Line mode Select SW Press Load Battery Input Output Run of Cap Cap Voltage Voltage Time Load Initial V X V 1st 2nd 3rd Ath Sth Return Pre
Download Pdf Manuals
Related Search