Philips HTS6515 DVD home theater system
Contents
1. INFO e Display the current status or disc information e Display photo files in 12 thumbnails view OPTIONS e Access or exit Options menu this menu provides various setting options Pill Play Pause e Start or pause disc play e RADIO start auto radio installation only available for first time setup E Stop e Stop disc play e RADIO erase the current preset radio station TREBLE BASS e Switch to treble or bass mode Then press VOL to set its level setting AUDIO SYNC e Select an audio language channel e Press and hold to access audio sync setting Then press VOL to set the audio delay time e RADIO toggle between FM stereo and mono mode SOUND e Select a predefined sound effect REPEAT PROGRAM e Select various repeat or shuffle modes turns off repeat or shuffle mode e RADIO press this button to start manual radio preset e RADIO press and hold this button to start automatic radio preset OK Confirm an entry or selection Cursor buttons A V lt 4 gt e Navigate through the on screen menu Press left or right for fast backward or forward search e RADIO press up or down to tune the radio frequency e RADIO press left or right to start auto search BACK TITLE e Return to the previous display menu For DVD go to title menu 2 e For VCD version 2 0 or SVCD with i PBC turned on return to the menu during playback k PI Previ2. USB Compatibility Hi Speed USB 2 0 Class support UMS USB Mass Storage Class Power Subwoofer e Power supply 110 127V 220 240V 50 60 Hz e Power consumption 150 W Standby power consumption Normal lt 3 W Low standby lt 0 3 W System Bass Reflex System e Impedance 4 ohm Speaker drivers 165 mm 6 1 2 woofer e Frequency response 30 Hz 160 Hz Dimensions WxHxD 295 x 440 x 295 mm e Weight 9 5 kg Main unit Dimensions WxHxD 419 x 48 x 214 mm Net Weight 1 7 kg Ambisound speakers e System full range satellite Speaker impedance 8 ohm channel 8 ohm centre channel Speaker drivers 2 5 full range channel e Frequency response 190 Hz 20 kHz Dimensions WxHxD 335 5 x 113 x 128 5 mm e Weight 1 72 kg EN 47 English Additional information 9 Troubleshooting e Risk of electric shock Never remove the casing of this unit To keep the warranty valid never try to repair the system yourself If you encounter problems when using this unit check the following points before requesting service If the problem remains unsolved register your product and get support at www philips com welcome Main unit The buttons on this unit do not work Disconnect this unit from the power outlet for a few minutes then connect again e Ensure that the interconnect cable from the subwoofer is connected to the DVD Home Theatre unit
3. Symbol Options Yi General Setup Q Audio Setup Ld Video Setup a Preference Setup General setup 1 Press OPTIONS General Setup menu is displayed 2 Press gt 3 Select an option then press OK General Setup EasyLink vi Disc Lock Q Display Dim OSD Language Screen Saver Sleep Timer 4a Standby Mode DivX R VOD Code e See the explanations of the above options in the following pages 4 Selecta setting then press OK e To return to the previous menu press BACK To exit the menu press OPTIONS 38 EN EasyLink This feature is only applicable if this unit is connected to HDMI CEC compliant TV device It enables all the linked devices response or react to certain commands simultaneously with one touch control Options Descriptions Auto Wake It wake ups your TV up TV automatically when you press PLAY to power up this unit and start disc play if a video disc is found in the disc compartment e To disable this feature select Off System Respond to standby Standby command from other HDMI CEC compliant TV devices e To disable this feature select Decline System Audio It enables this DVD Control Home Theatre unit to switch automatically to the audio input of the active device e To enable this feature select On Then proceed to Audio Input Mapping to scan an
4. Ambisound Setup Change the Ambisound setup Options Descriptions Room Select the type of walls Acoustics that surround your room Room Select this unit placement Placement in the room Speaker Select the distance Distance between two speakers Listening Select the distance Position between your listening position and this unit Tips for detailed information e See chapter Get Started Start Ambisound setup HDMI Audio When you connect th is unit and TV with HDMI cable select the audio output setting for this connection On the sound both your TV and f the audio format is output through his speaker system on the disc is not supported it will be downmixed to two channel sound linear PCM e Off disable audio output from Night Mode your TV The sound is only output hrough this speaker system Make loud sound level softer and soft sound level louder so that you can watch the DVD movies at a low volume without disturbing others On for quiet viewing at night DVDs only Off enjoy surround sound with a full dynamic range Video setup 1 Press OPTIONS General Setup menu is displayed 2 Press W to select LJ Video Setup then press P 3 Select an option then press OK Video Setup oR TV Type TV Display d Picture Settings HDMI Setup Ci Closed
5. Ambisound AMBISOUND PHILIPS OME THEATER SYSTEM 1 Press AMBISOUND repeatedly to select a best surround output that most suits the video or music you play Options Descriptions AUTO The surround output will be selected based on the audio stream of the played content MULTI Multi channel surround sound CHANNEL STEREO Stereo sound Select a preset sound effect son PHILIPS HOME THEATER SYST 1 Press SOUND repeatedly to select a sound effect that most suits the video or music you play Video Descriptions Music ACTION Enhanced low and high ROCK range for great sounding movie effects and atmosphere Great for action movies and rock pop music DRAMA Clear mid and high range JAZZ Recreates the atmosphere of a live club with the artist just in front of you Good for Jazz music and watching dramas CONCERT Flat and pure sound mode CLASSIC deal for listening to classical music and watching live concert DVDs GAMING Slightly enhanced low range PARTY and strong mid range ideal for party music and video gaming SPORTS Moderate mid range and surround effects for clear vocals and the atmosphere of a live sports venue NEWS Enhanced mid range for clear vocals speech EN 37 English Adjust sound 7 Adjust settings This section describes the various setting options of this unit
6. To change play speed press this button repeatedly For VCD only forward play is possible Display current play status e You can change the video play options here without interrupting disc play View DVD play from different camera angles e Only applicable to DVDs that contain sequences recorded from different camera angles EN 27 Access DVD menu 1 Press DISC to access disc main menu 2 Select a play option then press OK e n some menus press number buttons to input your selection To return to the title menu during playback press TITLE Access VCD menu The PBC Playback Control for VCD is turned on by default in the factory When you load in a VCD the contents menu is displayed 1 Press AY to select a play option then press OK to start play e If PBC is off it skips the menu and starts play from the first title e During playback you can press BACK to retum to the menu ifthe PBC mode is on Tips The default setting for PBC is on To change the default setting see chapter Adjust settings Preference Setup gt PBC for details 28 EN Sync audio output with video play f the video play is slower than the audio output sound does not match with the pictures you can delay the audio output to match the video AUDIO SYNC PHILIPS HOME THEATER SYSTEM 1 Press and hold AUDIO SYNC until AUD
7. Adjust settings gt General Setup gt DivX R VOD Code for details If the subtitle does not appear correctly change the subtitle language see chapter Adjust settings Preference Setup gt DivX Subtitle for details e The subtitle can only be displayed up to an average of 45 characters e This unit can play DivX video files that are up to 4GB in size EN 29 English Play Play music Note e For some commercial audio disc playback may resume from the point where it was last stopped To start playback from first track press I lt Control a track 1 Play a track 2 Use the remote control to control the track Button Action E Pause resume play Stop play ump to the next track Return to the beginning of the current track or jump to the previous track GEME MENE BED Direct input the track number Cc lt lt gt gt Search backward forward e To change search speed press this button repeatedly Toggle through various repeat PROGRAM shuffle play mode or turn off repeat mode e Repeat options vary depending on the disc type 30 EN Play MP3 WMA music MP3 WMA is a type of highly compressed audio file files with mp3 or wma extensions 1 Insert a disc or USB that contains the MP3 WMA music 2 Press DISC or USB A contents menu is displayed UJ Select a folder then press OK 4 Sel
8. Caption Progressive 40 00 See the explanations of the above options in the following pages 4 Selecta setting then press OK e To return to the previous menu press BACK To exit the menu press OPTIONS EN 41 English Adjust settings TV Type Change this setting only if the video does not appear correctly By default this setting matches the most common setting for TVs in your country e PAL for PAL system TV e NTSC for NTSC system TV e Multi for TV that is compatible with both PAL and NTSC TV Display Select the screen format according to how you want the picture to appear on your 4 3 Pan Scan PS Wo aad 16 9 Wide Screen 4 3 Letter Box LB 42 e 4 3 Pan Scan for standard TV a full height screen display with the sides trimmed e 4 3 Letter Box for standard TV a wide screen display with black bars on the top and bottom e 16 9 Wide Screen for wide screen TV frame ratio 16 9 Picture Settings Select a predefined set of picture colour settings or customise your personal setting Standard original colour setting Bright vibrant colour setting Soft warm colour setting e Personal customise the colour setting Set the level of brightness contrast tint and colour saturation in the menu then press OK EN HDMI Setup When you connect this u
9. INK repeatedly until MP3 from the DIGITAL IN COAXIAL socket Note on the subwoofer to the COAXIAL eT LINK is displayed on the display panel Note e To listen to the audio output from this connection press AUX DI MP3 LINK repeatedly until DIGITAL INPUT is displayed on the display panel Connect USB device O 1 Connect the USB device to 3 gt USB socket on this unit Note e This unit can only play view MP3 WMA DivX Ultra or JPEG files that are stored on such devices To listen to the audio output from this connection press USB EN 17 Attach table stand to DVD Home Theatre unit Mount the DVD Home Theatre unit 1 Ensure all the required cables are connected to this unit and close the rear cover 2 Attach the table stand bracket to the rear of this unit e Align the arrow indicators for correct positioning and placement e Use the protrude panels to hold the table stand bracket Align Arrow With table Stand 18 table stand bracket EN Caution e Risk of personal injury and damage to the unit Allow only qualified persons to mount the unit Ensure all the required cables are connected to this unit and close the rear cover 2 Attach the big wall mount bracket to table stand bracket with screws table stand bracket big
10. IO SYNC XXX is displayed e XXX denotes the delay time 2 Within five seconds press VOL to set the delay time for audio output Note e fthe volume control is not used within 5 seconds it resumes normal volume control function Quick skip play to a specific time 1 During playback press INFO 4 The disc status menu is displayed 2 Select the current elapsed playing time in the menu then press OK TT Time title time CH Time chapter time e Disc Time disc time Track Time track time 3 Press the number buttons to change the time where you want to skip to then press OK Play DivX video DivX video is a digital media format that retains high quality despite a high rate of compression This unit is DivX Certified that allows you to enjoy DivX video 1 Insert a disc or USB that contains the DivX videos 2 Press DISC or USB A contents menu is displayed UJ Select a title to play then press PAI 4 Use the remote control to control the title Button Action Change subtitle language SUBTITLE E ae Ch dio track Aue ange audio language trac Stop play e For DivX Ultra video press this button again to display the contents menu Display DivX Ultra video information Sipin e Only those DivX videos that were rented or purchased using the DivX registration code of this unit can be played see chapter
11. Input For example if your TV audio is connected to the AUX IN AUX 1 sockets on this unit select AUX1 Input and map with the TV brand name at the right panel elect the audio Input of this unit that Is 8 Select the audio input of this unit that i used to connect to other HDMI device e g AUX1 Input AUX2 Input then press gt 9 Select the correct device that connected to this audio input then press OK e Repeat steps 8 9 to map other connected devices 1 0 To exit the menu press OPTIONS Select a play source English On the main unit coomos SOURCE O Get started Press SOURCE button repeatedly to select DISC gt USB gt RADIO FM gt RADIO AM MW gt DIGITAL INPUT gt AUX1 INPUT gt AUX2 INPUT gt AUX3 INPUT gt MP3 LINK gt DISC On the remote control Press DISC to switch to DISC mode Press USB to switch to USB mode Press RADIO to switch to FM or AM MW band Press AUX DI MP3 LINK repeatedly to select other external devices Display Device connected to AUX1 INPUT AUDIO IN AUX1 sockets AUX2 INPUT AUDIO IN AUX2 sockets AUX3 INPUT AUDIO IN AUX3 sockets DIGITAL DIGITAL IN COAXIAL INPUT socket MP3 LINK MP3 LINK socket EN 25 5 Play Play from disc Playable discs Note e DVDs and DVD players are designed with regional restrictions Ensure that the DVD
12. ONS You can now turn on the progressive scan mode on your TV see the TV user manual Note There are some progressive scan TVs that are not fully compatible with this unit resulting in an unnatural picture when playing back a DVD VIDEO disc in the progressive scan mode In such case turn off the progressive scan feature on this unit and your TV EN 23 English Get started Activate EasyLink control Note e To enable one touch play function a video disc must This feature is only applicable if this unit is be placed in the disc compartment before operation connected to HDMI CEC compliant TV device e Philips does not guarantee 100 interoperability It enables all the linked devices response or With al PHDMICEC compliant devices react to certain commands simultaneously with one touch control Map the audio inputs to the 1 Turm on the HDMI CEC operations on connected devices your TV and other connected devices See TVs devices manual for details Note 2 You can now enjoy the EasyLink controls e Before you start ensure that an audio connection One touch play Auto Wake up TV has been made between this unit and your TV When you press PLAY button this unit will devices wake up from standby mode and start disc play if a video disc is found in the disc compartment and it will also turn on your TV and switch to the correct viewing channel Press DISC Press
13. OPTIONS General Setup menu is displayed w N Press One touch power off System Standby 4 When you press and hold STANDBY button it will turn off this unit and all the linked devices to standby This unit also responses to standby command from other HDMI CEC devices Select EasyLink then press General Setup EasyLink Disc Lock Q Display Dim OSD Language Auto Wake up TV System Standby System Audio Control Audio Input Mapping 24 One touch audio input switching System Gi Screen Saver Audio Control Sleep Timer This unit is able to render the audio signals eo Standby Mode from the active source It switches automatically to the corresponding audio input and output the sound from its speaker system e Before you can enjoy this function you have to map the audio inputs to the connected devices e You can use any HDMI CEC TV device remote control to adjust the volume EN Divx R VOD Code e Auto Wake up TV and System Standby functions are turned on by default in the factory 5 Select System Audio Control gt On then press OK 6 Select Audio Input Mapping J then press OK 7 Select OK in the menu then press OK to start scanning of devices 4 Once complete audio input mapping menu is displayed Audio Input Mapping AUX1 Input TV Yo AUX2 Input Other non HDMI ng AUX3 Input Digital
14. Old Password field 2 Enter the new password at New Password field 3 Enter the new password again at Confirm PWD field 4 Press OK to exit the menu Note before you set a new password 44 EN DivX Subtitle Select a character set that supports the DivX subtitle Standard English Chinese Simplified Chinese Korean Korean Note Ensure that the subtitle file has the exact same file name as the movie file If for example the filename of the movie is Movie avi then you will need to name the text file Movie sub or Movie srt Version Info Display the software version of this unit Tips This information is required when you want to find out if a newest software version is available at the Philips website that you may download and install on this unit Default Reset all the settings of this unit to factory default except for Disc Lock Password and Parental settings remain unchanged EN 45 English Adjust settings 8 Additional information Update software Philips provides software updates to ensure that this unit is compatible with the newest formats To check for updates compare the current software version of this unit with the latest software version available at the Philips website 1 Press OPTIONS Preference Setup Disc Menu vi Paren
15. Picture No picture No picture on HDMI connection 48 EN See TVs manual for correct video input channel selection Change the TV channel until you see the DVD screen e Press DISC e If this happens when you turn on the progressive scan setting or change the TV type setting you have to switch to its default mode 1 Press amp to open the disc compartment 2 Press gt for progressive scan or lt for TV type 3 Press SUBTITLE e Check if the HDMI cable is faulty Replace a new HDMI cable e If this happens when you change the HDMI video resolution press HDMI repeatedly until the picture appears Sound No sound No sound on HDMI connection No sound from TV programmes English Ensure that the audio cables are connected and press the correct input source for example AUX DI MP3 LINK USB to select the device you want to play You may not hear any sound from the HDMI output if the connected device is non HDCP compliant or only DVI compatible Ensure that the HDMI Audio setting is turned on Troubleshooting Connect an audio cable from the AUDIO input on this unit to the AUDIO output on your TV Then press AUX DI MP3 LINK repeatedly to select the corresponding audio input source Play DivX video files cannot be played The aspect ratio of the screen is not aligned with the TV display setting DivX subtitle are not displayed correctly The contents of the USB flash dr
16. Register your product and get support at www philips com welcome HTS6515 EN DVD Home Theatre System 5 ZH_CN DVD REKKAA 51 ZH_TW DVD RERA 7 MS_MY Sistem Teater Rumah DVD 143 PHILIPS BSA EWAMTA Hazardous Toxic Substance DEB ER B X Hg m Cd TAN ZRKA SRO AR Name of the Parts Pb Lead Mercury Cadmium Chromium 6 PBB PBDE Housing O O O 0 O 0 hse VD loader X O O O O O VD kA Subwoofer x o o o o o RA Loudspeakers O 0 Oo O O 0 HV LTE PWBs X 0 O O o O HB AREAL Accessories x o o o o o Remote control amp cables ME CESAS DEBE ERR Batteries in X oO O O O 0 Remote Control ZnC EE a tL O RZB GH EW EAE AB Ee EES T T 11363 2006 PRERE BEEBE RLF o O Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ T11363 2006 X KRZA EA ED LEE RS SSO ED RE HSJ T11363 2006 PERUENIRE X Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ T11363 2006 LD EZA HAPR Environmental Protection Use Period Webs PATS IB FE Me eB 8 RR EE HT SR EB ANS EDP GEAR LP Pg th Ne i BOE at he IBR x This logo refers to the period 10 years during which the toxic or hazardous sub
17. TV can support progressive signals you can activate the progressive scan mode of this unit On turm on progressive scan mode Off disable progressive scan mode Tips e See chapter Get Started Turn on Progressive Scan for detailed information Preference Setup 1 Press OPTIONS General Setup menu is displayed 2 Press W to select 43 Preference Setup P then press P 3 Select an option then press OK Preference Setup Audio i Subtitle d Disc Menu Parental PBC MP3 JPEG Nav Password DivX Subtitle v e See the explanations of the above options in the following pages 4 Selecta setting then press OK e To return to the previous menu press BACK To exit the menu press OPTIONS EN 43 English Adjust settings Audio Select the default audio language for DVDs Subtitle Select the default subtitle language for DVDs Disc Menu Select the menu language for DVDs If the language you have set is not available on the disc the disc uses its own default language For some DVDs the subtitle audio language can only be changed from the disc menu To select the languages that are not listed in the menu select Others Then check the Language Code list at the back of this user manual and Enter the respective 4 digit language code Parental Restrict access to DVDs that are uns
18. Your product Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome This DVD Home Theatre is designed to complement your home perfectly Enjoy the DVD Home Theatre with multi channel surround sound and excellent picture quality Features highlight Video upscaling to 1080p You can now watch the DVDs in the highest picture quality available for your HDTV This DVD Home Theatre offers full high definition video playback up to 1080p resolution for an amazing viewing experience A highly detailed picture and increased sharpness delivers a more rue to life picture EasyLink EasyLink uses the HDMI CEC Consumer Electronics Control industry standard protocol o share functionality with all HDMI CEC compliant devices over HDMI It enables the connected devices to control each other with a single remote control Note e Philips does not guarantee 100 interoperability with all HDMI CEC devices Ambisound Philips Ambisound technology reproduces multi channel surround sound with fewer speakers to give an embracing surround experience without the hassle of setting up a full range of speaker systems USB direct and MP3 link Simply plug your USB device into the USB socket to play your MP3 WMAV JPEG Divx files or plug your portable media player to the MP3 LINK socket to enjoy the music play in superb sound q
19. at step 2 until you tune to the radio station you wish to store To finetune the radio frequency press AV 4 Press PROGRAM e If no action is carried out within 20 seconds after the above step it exits the preset mode 5 Press I Pl or the number buttons to select a preset number to store 6 Press PROGRAM to confirm Change tuning grid In some countries the frequency step between adjacent channels in FM band is 50 kHz or 100 kHz AM MW band is 9 kHz or 10 kHz Note e This feature only applicable for certain region e Change tuning grid erases all preset radio stations Press RADIO repeatedly to select FM or AM MW band Press Ml Ww N Press and hold PHI until GRID 9 or GRID 10 is displayed e GRID 9 for FM 50 kHz or AM 9 kHz and GRID 10 for FM 100 kHz or AM 10 kHz EN 35 English Play 6 Adjust sound Control the volume 1 Press VOL to increase or decrease the volume level To mute the volume press R To restore the volume press nXK again or press the volume button Adjust Bass Treble TREBLE BASS PHILIPS HOME THEATER SYSTEM 1 Press BASS TREBLE Press VOL repeatedly to set the level for low BASS or high TREBLE tone Note e fthe volume control is not used within 10 seconds it resumes normal volume control function 36 EN Select
20. bles 12 Connect speakers to subwoofer 14 Connect subwoofer 15 Connect radio antenna 15 Connect audio cables other devices 16 Attach table stand to DVD Home Theatre unit 18 ount the DVD Home Theatre unit 18 ount the speakers 19 4 Get started 20 Prepare the remote control 20 Find the correct viewing channel 21 Select menu display language 21 Start Ambisound setup 22 Turn on Progressive Scan 23 Activate EasyLink control 24 Select a play source 25 5 Play 26 Play from disc 26 Play video 27 Play music 30 Play photo 31 Play from USB device 32 Play from portable media player 33 Play from radio 33 6 Adjust sound 36 Control the volume 36 Adjust Bass Treble 36 Select Ambisound 36 Select a preset sound effect 37 7 Adjust settings 38 General setup 38 Audio setup 40 Video setup 41 Preference Setup 43 8 Additional information 46 Update software 46 Care 46 Specifications 47 9 Troubleshooting 48 10 Glossary 50 EN 5 English Contents 1 Important Safety and important notice Risk of fire or electric shock e Ensure that air can circulate freely through the ventilation holes on this unit Allow at least 5 10 cm clearance around the unit Never expose this unit to direct sunlight naked flames or heat Never place this unit on other electrical equipment Keep away from this unit during lightning storms Never remove the casing of this unit Please leave all maintenance work to qualifie
21. ces EN 11 English Connect Connect video cables This section describes how to connect this DVD Home Theatre unit to your TV so to enable viewing of disc play Select the best video connection that your TV can support e Option 1 Connect to HDMI socket for a HDMI DVI or HDCP compliant TV e Option 2 Connect to component video socket for a standard TV or Progressive Scan TV e Option 3 Connect to video CVBS socket for a standard TV Note e You must connect this unit directly to a TV 12 EN Before you connect d Push up the catch and remove the rear cover 2 Connect the cables to the corresponding sockets and direct the cables to the open hole on top UI Once complete close the rear cover Note e All the cables must be placed properly inside the rear panel in order for the rear cover to close Option 1 Connect to HDMI socket Option 2 Connect to component video socket 1 Connect a HDMI cable supplied from the HDMI OUT on this unit to the HDMI IN socket on your TV e The HDMI connector is only compatible with HDMI compliant TVs and DVI TVs E e To optimise the video output see chapter Adjust settings gt Video Setup gt HDMI Setup for details e This unit is HDMI CEC compatible It enables connected TV device to con
22. d map all the connected devices Audio Input Map the audio input to Mapping the connected TV devices correctly to enable automatic switching of input source 1 Press OK to start scanning of devices 2 Select the audio input o map e g AUX1 nput AUX2 Input hen press P 3 Select the correct device that connected o this audio input hen press OK Note e Your TV and other connected devices must be compliant with HDMI CEC e You must turn on the HDMI CEC operations on your TV devices before you can enjoy the EasyLink controls See your TVs devices manual for details e Philips does not guarantee 100 interoperability with all HDMI CEC compliant devices Disc Lock Set play restriction for a specific discs Before you start place the disc in the disc compartment maximum 40 discs can be locked e Lock restrict access to the current disc The next time you want to play this disc or unlock it you need to enter the password e Unlock all discs can be played Tips e To set or change your password go to Preference Setup gt Password Display Dim Change the brightness level of the display panel to suit the lighting in your room e 100 normal brightness 70 medium brightness e 40 dimmest display The LEDs and display icons will not be shown English OSD Language Select the default on screen men
23. d personnel Keep this unit away from water moisture and liquid filled objects Caution Remove batteries if they are exhausted or if the remote control is not to be used for a long time Do not mix batteries old and new or carbon and alkaline etc Batteries contain chemical substances they should be disposed of properly Visible and invisible laser radiation when open Avoid exposure to beam Where the MAINS plug or an appliance coupler is used as the disconnect device the disconnect device shall remain readily operable 6 EN Recycle notice H amp S This electronic equipment contains a large number of materials that can be recycled or reused if disassembled by a specialised company If you are disposing of an old machine please take it to a recycling centre Please observe the local regulations regarding disposal of packaging materials exhausted batteries and old equipment Copyright notice Be responsible Respect copyrights This product incorporates copyright protection echnology that is protected by method claims of certain U S patents and other intellectual property rights owned by Macrovision Corporation and other rights owners Use of his copyright protection technology must be authorised by Macrovision Corporation and is intended for home and other limited viewing uses only unless otherwise authorised by acrovision Corporation Reverse engineering or disassembly is prohibited 2
24. d searching PCM Pulse Code Modulation A digital audio encoding system Progressive Scan The progressive scan displays twice the number of frames per seconds than ordinary TV system It offers higher picture resolution and quality WMA Windows Media Audio Refers to an audio compression technology developed by Microsoft Corporation WMA data can be encoded by using Windows Media Player version 9 or Windows Media Player for Windows XP Files are recognised by their file extension WMA
25. digital interface that can transmit uncompressed high definition video and digital multichannel audio It delivers high quality picture and sound quality completely free from noise HDMI is fully backward compatible with DVI As required by the HDMI standard connecting o HDMI or DVI products without HDCP High bandwidth Digital Content Protection will result in no Video or Audio output HDCP High bandwidth Digital Content Protection is a specification that provides a secure transmission of digital contents between different devices to prevent unauthorised copyright 50 EN JPEG A very common digital still picture format A still picture data compression system proposed by the Joint Photographic Expert Group which features small decrease in image quality in spite of its high compression ratio Files are recognised by their file extension JPG or JPEG MP3 A file format with a sound data compression system MP3 is the abbreviation of Motion Picture Experts Group 1 or MPEG 1 Audio Layer3 By using the MP3 format one CD R or CD RW can contain about 10 times more data than a regular CD Files are recognised by their file extension MP3 MPEG Motion Picture Experts Group A collection of compression systems for digital audio and video PBC Playback Control A system of navigating a Video CD Super VCD through on screen menus recorded onto the disc You can enjoy interactive playback an
26. e it tunes to the first preset radio station To stop auto tuning press W Note Listen to radio 1 Press RADIO repeatedly to select FM or AM MW band 2 Use the remote control to contro the radio Button Action O Select a preset radio station lt lt gt gt Tune the radio frequency backward forward Toggle between FM stereo AUDIO SYNC and FM mono mode e This unit can store up to a maximum of 40 FM radio stations 20 radio stations for AM MW band e If auto installation is not activated or less than 5 radio stations are stored AUTO INSTALL will be displayed again the next time you turn on to radio mode 34 EN Press and hold this button to delete the preset station from the preset list e The preset number for other radio stations remain unchanged Reinstall all the radio stations 1 Press RADIO repeatedly to select FM or AM MW band 2 Press and hold PROGRAM until STARTING INSTALL is displayed All previously stored radio stations will be replaced Note e fno stereo signal is detected or less than 5 stations are detected during radio installation CHECK ANTENNA is displayed Search and store radio stations individually 1 Press RADIO repeatedly to select FM or AM MW band 2 Press lt lt DP gt The radio frequency indication starts to change until a radio station is detected 3 Repe
27. e menu 1 Point the remote control directly at the remote sensor on this unit and select the desired function Use the following buttons on the remote control to navigate through the on screen menus Button Action AV Move up or down lt gt Move left or right Confirm a selection JO Enter numbers i Find the correct viewing channel 1 Press C to turn on the DVD Home Theatre unit 2 Press DISC to switch to disc mode 3 Tum on the TV and switch it to the correct video in channel e You may go to the lowest channel on your TV then press the Channel Down button on your TVs remote control until you see the Video In channel You may press button repeatedly on your TVs remote control e Usually this channel is between the lowest and highest channels and may be called FRONT A V IN VIDEO etc Tips See the TVs user manual on how to select the correct input on your TV Select menu display language Note e You can skip this setting if this unit is connected to a HDMI CEC compliant TV It switches automatically to the same OSD menu language as per your TV setting 1 Press DISC Press OPTIONS General Setup menu is displayed UI Press gt 4 Press AV to select OSD Language in he menu then press P General Setup A EasyLink Disc Lock English d Display Dim AS set CI Screen Sav
28. ect a track to play then press PAI e To return to the main menu press A until Previous folder is selected then press OK e For CDs recorded in multiple sessions only the first session is played e This unit does not support MP3PRO audio format e fany special characters are present in the MP3 track name ID3 or album name it might not be displayed correctly on the screen because these characters are not supported e Some WMA is protected by Digital Rights Management DRM it cannot be played on this unit Folders files exceed the supported file limit of this unit will not be displayed or played Ea e To display the data disc contents without folders see chapter Adjust settings Preference Setup gt MP3 JPEG Nay for details Play photo Play photos as slideshow This unit can play JPEG photos files with jpeg or jpg extensions 1 2 Insert a disc or USB that contains the JPEG photos Press DISC or USB L For a Kodak disc the slideshow begins automatically L gt For a JPEG disc the photo menu is displayed Select the folder album you want to play To preview the photos in the folder album press INFO gt i gt i To go to previous or next screen display press ME Pl e To select a photo press the cursor buttons e To display the selected photo only press OK Press H to start slideshow play e To ret
29. er Melayu Sleep Timer PyccKkn gg Standby Mode Ine DivX R VOD Code e The language options are different depending on your country or region It may not correspond to the illustration shown here 5 Press AV to select a language then press OK Tips e To set the default language for DVD audio and disc menu see chapter Adjust settings Preference Setup for details EN 21 English Get started Start Ambisound setup Change the Ambisound setup according to your room environment and setup in order to obtain the best possible surround sound effect 1 Press DISC Press OPTIONS 3 Press W to select Q Audio Setup in the menu then press P Audio Setup Ambisound Setup HDMI Audio Night Mode s 0p e To access Ambisound setup option this DVD Home Theatre unit must be in a complete stop mode Press ll twice if necessary 4 Select Ambisound Setup in the menu then press gt Ambisound Setup Hard Room Placement Soft Speaker Distance Listening Position as 4 amp Ea 22 EN Select a setup you want to change then press P Type of wall that surround your room Room Acoustics Hard concrete wood Soft curtains open space Speakers placement in your room Room Placement e Middle of room Corner of room e Near the right wall Near the left wa
30. hannel surround capabilities Connect audio from TV also used for EasyLink control 1 Connect an audio cable not supplied from the AUDIO IN AUX1 sockets on this unit to the AUDIO OUT sockets on your TV Note e To listen to the audio output from this connection press AUX DI MP3 LINK repeatedly until AUX1 INPUT is displayed on the display panel 16 EN Connect audio from cable box recorder game console You can choose to connect to analogue or digital socket depending on the device capabilities Connect to analogue sockets 1 Connect an audio cable not supplied from the AUDIO IN AUX2 or AUX3 sockets on the subwoofer to the AUDIO OUT sockets on the device Note e To listen to the audio output from this connection press AUX DI MP3 LINK repeatedly until AUX2 INPUT or AUX3 INPUT is displayed on the display panel Connect to digital socket 7 e Connect portable media player Ga DIGITAL IN English Connect 1 Connect a 3 5mm stereo audio cable not supplied from the MP3 LINK socket on this unit to the phone socket on your portable media player such as MP3 player 1 Connect a coaxial cable not supplied DIGITAL OUT socket on the device o listen to the audio output from this connection press AUX DI MP3 L
31. into the socket e To disconnect the Ambisound speakers press down the catch on the plug before pulling out Tips e The video input socket on your TV may be labeled as A V IN VIDEO IN COMPOSITE or BASEBAND e This type of connections provide standard picture quality 14 EN Connect subwoofer Connect radio antenna C IO o 0000 x 1 Unwind the subwoofer s interconnect cable at TO MAIN UNIT and connect it to the TO SUBWOOFER socket on this unit 1 Stand the AM MW loop antenna supplied upright to fix its claw into the slot 2 Connect the AM MW loop antenna to the AM MW socket Then place the AM MW loop antenna on a shelf or attach it to a stand or wall 3 Connect the FM antenna supplied to the FM75Q socket on this unit for some models this cable has been connected Extend the FM antenna and fix its ends to the wall 4 Connect the power cord when all the required connections are complete and you are ready to enjoy this DVD Home Theatre unit Note e Before connect to power outlet ensure that the voltage selector at the rear of this unit is set to the local power line voltage EN 15 English Connect Connect audio cables other devices This section describes how you can route the sound from other devices to this DVD Home Theatre unit in order to enjoy sound output or audio play with multi c
32. ivX video including DivX 6 with enhanced playback of Divx media files and the Divx Media Format Ay Pras a a Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and or other countries CLASS 1 LASER PRODUCT HDMI and HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC HI SPEED Va USB The USB IF Logos are trademarks of Universal Serial Bus Implementers Forum Inc ENERGY STAR and the ENERGY STAR mark are registered U S marks ENERGY STAR 3 CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE STANDARD DEFINITION OUTPUT IF THERE ARE QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p AND 625p DVD PLAYER PLEASE CONTACT OUR CUSTOMER SERVICE CENTER LASER e Type Semiconductor laser GaAlAs e Wave length 645 660 nm DVD 770 800 nm CD Output Power 6 mW DVD 7 mW VCD CD Beam divergence 60 degrees Contents 1 Important 6 Safety and important notice 2 Your product 7 Features highlight 7 Product overview 8 3 Connect 11 Place the unit 11 Connect video ca
33. ive cannot be read Ensure that the Divx file is encoded according to the Home Theatre Profile with the DivX encoder Ensure that the DivX video file is complete The aspect ratio is fixed on the DVD Ensure that the subtitle file name is the same as the movie file name Select the correct character set 1 Press OPTIONS 2 Press then select DivX Subtitle in the menu 3 Select the character set that supports the subtitle The USB flash drive format is not compatible with this unit Drive is formatted with different file system which is not supported by this unit e g NTFS Maximum size of memory supported is 160GB EN 49 10 Glossary Aspect ratio Aspect ratio refers to the length to height ratio of TV screens The ratio of a standard TV is 4 3 while the ratio of a high definition or wide TV is 16 9 The letter box allows you to enjoy a picture with a wider perspective on a standard 4 3 screen DivX The DivX code is a patent pending MPEG 4 based video compression technology developed by DivX Networks Inc that can shrink digital video to sizes small enough to be transported over the internet while maintaining high visual quality Dolby Digital A surround sound system developed by Dolby Laboratories containing up to six channels of digital audio front left and right surround left and right centre and subwoofer HDMI High Definition Multimedia Interface HDMI is a high speed
34. l and batteries Composite video cable yellow e HDMI cable e Power cable for certain region only Subwoofer Component video cables e 2 Ambisound speakers 1 main unit wall mount bracket and 2 speakers wall mount bracket e Mounting knob to secure the main unit to the bracket e Table stand with screws for main unit e FM wire antenna AM MW loop antenna Round to Flat pin adaptor for certain region only e Micro fibre cleaning cloth Amplifier Total output power Home Theatre 600W e Frequency response 20 Hz 20 kHz 3dB Signal to noise ratio gt 65 dB CCIR Input sensitivity AUX 1 800 mV MP3 LINK 370 mV Disc e Laser Type Semiconductor e Disc diameter 12cm 8cm Video decording MPEG1 MPEG2 Divx DivX Ultra Video DAC 12 bits 148 MHz e Signal system PAL NTSC Video S N 56 dB e Audio DAC 24 bits 192 kHz e Frequency response 20 Hz 20 kHz PCM IEC 60958 Dolby Digital DTS IEC60958 IEC61937 Radio Tuning range FM 87 5 108 MHz 100 kHz AM MW 531 1602 kHz 9 kHz AM MW 530 1700 kHz 10 kHz 26 dB quieting sensitivity FM 22 dBf AM 4uV m e F rejection ratio FM 60 dB AM 45 dB Signal to noise ratio FM 60 dB AM 40 dB Harmonic distortion FM 3 AM 3 Frequency response FM 180 Hz 9 kHz 6dB Stereo separation FM 26 dB 1 kHz Stereo Threshold FM 23 5 dB
35. ll Distance between two speakers Speaker Distance Near lt 2m 78in Default 2m 3m 78 118in Far gt 3m 118in Distance between the listening position and the speakers Listening Position Near lt 2m 78in Default 2m 3m 78 118in Far gt 3m 118in Press AY to select a setting then press OK To exit the menu press OPTIONS Turn on Progressive Scan If you connect this unit to TV with the component video connection see chapter Connect video cables Option 2 Connect to component video socket for details you can turn on the progressive scan output if your TV supports progressive scan 1 Tum on the TV to the correct viewing channel for this unit 2 Press DISC 3 Press OPTIONS 4 Press W to select GJ Video Setup in the menu then press P Video Setup TV Type Yi TV Display a Picture Settings HDMI Setup Closed Caption 5 Select Progressive gt On then press OK 4 A warning message is displayed 6 To proceed select OK in the menu and press OK 4 The progressive setup is complete Note e Ifa blank distorted screen is displayed wait for 15 seconds for the auto recover e f no picture displayed turn off the progressive scan mode as follows 1 Press amp to open the disc compartment 2 Press 3 Press SUBTITLE N To exit the menu press OPTI
36. nit and TV with HDMI cable select the best HDMI setup that your TV can support Wide Screen Format define the wide screen format for disc play Options Descriptions Superwide Centre position of the screen is stretched less than the side This setting is only applicable if the video resolution is set to 720p or 1080i p 4 3 Pillar o stretching of the Box picture Black bars are displayed on both sides of the screen Off Picture will be displayed according to the format of the disc Note e This setting is only available if you have set the TV Display setting to 16 9 Wide Screen e HDMI Video select a video resolution that is compatible with your TV display capability Options Descriptions Auto It detects and selects the best supported video resolution automatically 480p 576p Select a video resolution 720p 1080i that best supported by 1080p your TV See your TVs manual for details Note e Ifthe setting is not compatible with your TV a blank screen appears Wait for 15 seconds for auto recover or press HDMI repeatedly until the picture appears Closed Caption Turn on or off display captions On show the sound effects in subtitle Only applicable to disc with Closed Caption information included and your TV supports this feature Off disable closed caption Progressive If your
37. o audio cable not supplied from the MP3 LINK socket on this unit to the headphone socket on your portable media player 2 Press AUX DI MP3 LINK repeatedly until MP3 LINK is displayed 3 Start play on your portable media player e See chapter Adjust Sound to enhance the audio output 4 To stop play press STOP button on your portable media player Note Play from radio Check if the FM antenna has been connected to the subwoofer If not connect the supplied FM antenna to the FM 75Q socket and fix its ends to the wall e For China Latin America region only if you want to receive AM MW radio band connect the AM loop antenna supplied to the AM MW sockets on this DVD Home Theatre unit Ea e For better FM stereo reception connect an external FM antenna not supplied e Position the antenna as far away as possible from your TV VCR or other radiation source to prevent unwanted interference Control playback is only possible on your portable media player Stop play on the portable media player before you switch to other play media source EN 33 English Play First time tuning The first time when you access RADIO mode follow the instructions to install the radio stations 1 Press RADIO 4 AUTO INSTALL PRESS PLAY is displayed 2 Press PAI gt All detected radio stations are stored D Once complet
38. older or album 4 Audio continues to play till the end of the disc e To return to the menu press BACK To stop slideshow play press Hl To stop music play press lll again EN Play from USB device This unit can only play view MP3 WMA Divx Ultra or JPEG files that are stored on such devices 1 Connect a digital camera that comply w ith the PTP standard USB flash drive or USB memory card reader to the gt e USB socket on this unit 2 Press USB gt A contents menu is displayed 3 Selecta file to play then press PAI For more information see chapters Play music Play photo Play video for details 4 To stop play press Il or remove the USB device Ea e fthe device does not fit into the USB socket connect it through a USB extension cable connected USB drive contents can be accessed e Ifa USB HDD is used ensure that an auxiliary operations e Digital cameras that use PTP protocol or require o a PC are not supported e Ifa multiple USB card reader is used only one of the power cord connected to the USB HDD for proper additional programme installation when connected Play from portable media player Simply connect your portable media player e g P3 player to this unit to enjoy superb sound quality from your music collections 1 Connect a 3 5mm stere
39. ous Next a e Skip to the previous or next title E chapter track e RADIO select a preset radio station 8 K Mute e Mute or restore the volume VOL e Adjust the volume level AMBISOUND Select different surround sound output auto multi channel or stereo Numeric buttons e Enter a preset number or item to play SUBTITLE Select DVD or DivX subtitle language ZOOM e Zoom in or out the picture on the TV ANGLE e Select a different viewing angle of a DVD movie EN 9 Main unit MP3 LINK SOURCE OOOOO Standby on Turn on this unit or tum off to standby mode OO e Press and hold to turn on this unit from a low power standby mode Pil Play Pause e Start or pause disc play e RADIO start auto radio installation only available for first time setup VOL e Adjust the volume level SOURCE e Select a play media DISC USB RADIO FM RADIO AM MW DIGITAL INPUT AUX1 INPUT AUX2 INPUT AUX3 INPUT or MP3 LINK amp Open Close Open or close the disc compartment Disc compartment 10 EN gt USB socket e To connect USB flash drive USB memory reader or digital camera MP3 LINK socket To connect portable audio player Q Display panel 3 Connect This section describes the basic connections required for this DVD Home Theatre unit before it can be used Basic connection
40. s e Place the unit Connect video cables Connect speakers to subwoofer Connect subwoofer Connect radio antenna Optional connections Connect audio cables other devices Connect audio from TV Connect audio from cable box recorder game console Connect portable media player Connect USB device e Attach table stand to DVD Home Theatre unit e Mount the DVD Home Theatre unit e Mount the speakers Note e Refer to the type plate at the rear or bottom of the product for identification and supply ratings e Before you make or change any connections ensure that all the devices are disconnected from the power outlet Place the unit e Place this unit on top of a table or mount it on the wall see chapter Mount the DVD Home Theatre unit and Mount the speakers e Never place this unit in an enclosed cabinet e Install this unit near the AC outlet where he AC power plug can be easily reached LEFT 1 Place this DVD Home Theatre unit near to the TV e Attach the table stand to the DVD Home Theatre unit before place it on a table top 2 Place the speakers at the normal listening ear level and directly parallel to the listening area 3 Place the subwoofer at the corner of the room or at least one metre away from the TV Note e To avoid magnetic interference or unwanted noise never place the speakers too close to the TV or any radiation devi
41. stances or elements contained in electronic information products will not leak or mutate so that the use of these substances or elements will not result in any severe environmental pollution any bodily injury or damage to any assets E ttRiR Battery labeling logo WP N HABR Environmental Protection Use Period ERRIREN CTA FEU Aa J RR ETE BER EB AS 2s BE I BE BR MPE Masih PRR E eT A E FH SBR o HE7 This logo refers to the period 5 years during which the toxic or hazardous substances or elements contained in the battery will not leak or mutate so that the use of these substances or elements will not result in any severe environmental pollution any bodily injury or damage to any assets OO potey DIGITAL PRO LOGIC I Manufactured under license from Dolby Laboratories Dolby Pro Logic and the double D symbol are trademarks of Dolby Laboratories Digital Surround Manufactured under license under U S Patent s 5 451 942 5 956 674 5 974 380 5 978 762 6 487 535 amp other U S and worldwide patents issued amp pending DTS and DTS Digital Surround are registered trademarks and the DTS logos and Symbol are trademarks of DTS Inc 1996 2007 DTS Inc All Rights Reserved ULTRA Divx DivX Ultra Certified and associated logos are trademarks of DivX Inc and are used under icense Official DivXx Ultra Certified product Plays all versions of D
42. t automatically switches to standby mode if you do not press any buttons within 30 minutes after a disc has stopped playing diet Super Video CD SUPER VIDEO 26 EN Play video Note e For video disc playback always resumes from the point where it was last stopped To start playback from the beginning press I while the message is displayed Control a title 1 Play a title 2 Use the remote control to control the title Button Action E Pause resume play Stop play Jump to the next title chapter Return to the beginning of the current title chapter or jump to the previous title chapter Change video play a 1 Play a title T w 2 Use the remote control to change the video play amp Button Action a Change audio language e Only applicable to discs with multiple audio language or channel Change subtitle language e Only applicable to discs with multiple subtitle language Toggle through various repeat PROGRAM shuffle play mode or turn off repeat mode e Repeat options vary depending on the disc type e For VCDs repeat play is only possible when the PBC mode is turned off 700M Zoom in out e To pan through the zoomed image press the cursor buttons lt lt gt gt Search backward forward e To change search speed press this button repeatedly AY Slow motion reverse forward play e
43. tal nd gt PBC MP3 JPEG Nav CI Password DivX Subtitle Version Info Default 2 Select Preference Setup gt Version Info then press OK 3 Write down the version number then press OPTIONS to exit the menu 4 Goto www philips com support to check he latest software version available for this unit 5 Ifthe latest software version is higher than he software version of this unit download it and store onto a CD R or USB flash drive 46 EN 6 Insert the CD R or USB flash drive to this unit 7 Press DISC or USB then follow the instruction on the TV to confirm update operation Note Do not remove the CD R or USB when software updating is in progress 0 0 Once software update is complete this unit turns off to standby automatically Note e We recommend that you disconnect the power cord for a few seconds and connect again to reboot the system Care Caution e Never use solvents such as benzene thinner cleaners available commercially or anti static sprays intended for discs Clean discs Wipe the disc with a micro fibre cleaning cloth from the centre to the edge in a straight line movement Clean main unit screen Wipe the screen surface with a micro fibre cleaning cloth Specifications Note e Specification and design are subject to change without notice Accessories supplied e Quick Start Guide e Remote contro
44. trol each other over HDMI see chapter Activate EasyLink control for details e Use a HDMI DVI adaptor in case your TV has only a DVI connection An extra audio connection is needed to complete this connection e To route the audio from your TV to this DVD Home Theatre unit connect an audio cable from the audio input on this unit to the audio output on your TV e This type of connections provide best picture quality COMPONEN CE voo our PriCr Pb Cb Y 1 Connect the component video cable supplied from the COMPONENT VIDEO OUT socket on this unit to the component video input sockets on your TV e f a progressive scan TV is used you may turn on the progressive scan mode see chapter Turn on Progressive Scan for details Tips e The component video input socket on your TV may be labelled as Y Pb Cb Pr Cr or YUV e This type of connections provide good picture quality EN 13 English Connect Option 3 Connect to Video CVBS Connect speakers to socket subwoofer 1 Connect the left and right Ambisound speakers to the matching sockets on the subwoofer 1 Connect a composite video cable supplied from the VIDEO OUT socket Note on this unit to the video input socket on TV P e Ensure that the front portion of the plug is fully your inserted
45. u language Adjust settings Screen Saver Turn off or on the screen saver mode It helps to protect the TV screen from being damage due to over exposure to a static image for too long On set the screen saver to appear after 15 minutes of inactivity for example in pause or stop mode e Off disable screen saver mode Sleep Timer Switch to standby automatically after the preset time e Off disable sleep mode e 15 30 45 60 mins select the count down time before it switches to standby Standby Mode Set the standby mode Normal normal standby power consumption e Low Power low standby power consumption However it requires longer time to power up EN 39 Divx R VOD Code Display the DivX registration code Tips e Enter this unit s DivX registration code when you rent or purchase video from www divx com vod The DivX videos rented or purchased through the DivX VOD Video On Demand service can be played only on the device to which it is registered 40 EN Audio setup Press OPTIONS General Setup menu is displayed Press W to select Q Audio Setup then press P Select an option then press OK Yi Audio Setup Ambisound Setup HDMI Audio nd Night Mode Select a setting then press OK To return to the previous menu press BACK e To exit the menu press OPTIONS
46. uality Sync the audio output with the video play This DVD Home Theatre provides you the feature of delaying the audio output if the video signals that go directly to the TV is slower than the audio streams Region codes DVD movies are usually not released at the same time in all regions of the world thus all DVD players are programmed to a specific region code Countries Asia Pacific Taiwan Korea U lt g 5 oa 3 a a Australia New Zealand China India aao ee ee English Your product Product overview Remote control 60 O e 000 0 O Fi J SUBTITLE o fo SYNC m Coon ote verent son PROGRAM GOO O amp O PHILIPS HOME THEATER SYSTEM m N OO e Tum on this unit or tum off to standby mode e Press and hold to turn off this unit and all the HDMI CEC compliant TV devices for EasyLink control only amp Open Close e Open or close the disc compartment Source buttons e DISC switch to DISC mode While in disc mode access or exit disc menu e USB switch to USB mode e RADIO switch to FM or AM MW band e AUX DI MP3 LINK switch to AUX1 INPUT AUX2 INPUT AUX3 INPUT DIGITAL INPUT or MP3 LINK that corresponds to the socket you used to connect the extemal device HDMI e Select a video resolution setting for HDMI output
47. uitable for your children These types of DVDs must be recorded with ratings 1 To start press OK 2 Select a rating level in the menu then press OK 3 Press the number buttons to Enter your 6 digit password Rated DVDs above the level you set in Parental require a password to be played The ratings are country dependent To allow all discs to play select 8 Some DVDs have ratings printed on them but are not recorded with ratings This function has no effect on such DVDs Ea e Ifyou forget your 6 digit password Enter 136900 To set or change your password go to Preference Setup gt Password PBC For VCDs SVCDs recorded with PBC playback control you can access the disc contents through an interactive menu On an index menu is displayed when you load a disc for play Off skip the menu and start play from the first title MP3 JPEG Nav Turn off or on MP3 WMA folder display when you play a media that contains MP3 WMA files Without Menu display all the files e With Menu display the folders of MP3 WMA files Password Follow the instructions on the TV to set or change the password for locked discs and play restricted DVDs Change Password Old Password New Password Confirm PWD OK 1 Press the number buttons to Enter 136900 or your last set 6 digit password at
48. urn to the menu press BACK It may require longer time to display the disc contents on the TV due to the large number of songs photos compiled onto one disc If the JPEG photo is not recorded with an exif type file the actual thumbnail picture will not be shown on the display It will be replaced with a blue mountain thumbnail picture This unit can only display digital camera pictures according to the JPEG EXIF format typically used by almost all digital cameras It cannot display Motion JPEG and pictures in formats other than JPEG or sound clips associated with pictures Folders files exceed the supported file limit of this unit will not be displayed or played Control photo play 1 2 Play photo slideshow Use the remote control to control the photo Button Action lt Skip to the previous photo Skip to the next photo A Rotate the photo clockwise v Rotate the photo anti clockwise Zoom in out e Play will pause while in zoom mode Stop play EN 31 English Play Play musical slideshow Play files simultaneously to create musical slideshow The P3 WMA music files and JPEG photo P3 WMA and JPEG files must be stored on the same disc or USB device 1 2 UJ 32 Play MP3 WMA music avigate to the photo folder album and press II to start slideshow play L Slideshow begins and continues till the end of the photo f
49. video you play is for the same region zone as your player indicated on its rear e This unit can support playback of the following file formats MP3 WMA JPEG Divx DVD Video e Region 3 Asia Pacific VIDEO Taiwan Korea e Region 4 Australia New Zealand Region 6 China e Region 5 India DVD RW DVD DVD Rewritable DVD R Dy DVD Recordable DVD R DL DVD R Double m DVD R DL det CD RW CD Rewritable ReWritable diet CD R CD Recordable COMPACT Audio CD Compact Disc Digital Audio DIGITAL AUDIO deR Video CD Formats 1 0 1 1 2 0 Play a disc Caution ever place any objects other than discs into the isc compartment ever touch the disc optical lens inside the disc compartment Press amp to open the disc compartment 2 Insert a disc with its label facing up For double sided disc load the side to play faces up 3 Press amp to close the disc compartment and start disc play e To view disc play tum on the TV to he correct viewing channel for this DVD Home Theatre unit 4 To stop disc play press W Ea e Ifthe password entry menu is displayed you have to Enter the 6 digit password before it can be played e Screen saver displays automatically if the disc play is stopped for about 15 minutes To wake up from screen saver press DISC e This uni
50. wall mount bracket Position the brackets on the wall drill four screw holes and secure the brackets onto the wall with screws not supplied Hook the DVD Home Theatre unit firmly onto the mounted bracket Mount the speakers Caution e Risk of personal injury and damage to the unit Allow only qualified persons to mount the unit 1 Loosen the screws at the bottom of the speaker to remove the speaker stand 5 Screw the supplied knob to the hole at the centre rear to secure the DVD Home Theatre unit to the bracket 2 Attach the small wall mount bracket to the speaker with screws g X 3 Fix two screws not supplied to the wall then hook the bracket onto the screws and lock the speaker into position EN 19 English Connect 4 Get started Prepare the remote control UJ e Ifyou are not going to use the remote control for a long time remove the batteries Push to open the battery compartment cover Insert two batteries type RO3 or AAA Match the indications inside the battery compartment Close the cover Note 20 EN Control a play source 1 Select the source you wish to control by pressing the DISC USB RADIO or AUX DI MP3 LINK button Then select the desired function for example I Pl Navigate through th
Download Pdf Manuals
Related Search