NEC WT40SN 40"
Contents
1. unit from coming off W Setting the Projector on the Screen SS 3 Slide the projector left or right forward The setting procedure is the same when the screen is mounted on the dedicated stand or backward so that the lower edge of the projected image in the horizontal Preparations Shorten the projector s feet direction fits over the full width of the Turn the four feet clockwise for the WT610 WT615 and make them as short as possible screen For details refer to the projector s user s manual In case The picture is shifted left or right Slide left or right to center the 1 Attach the wires to the bottom of the projector in two places Point the flat surface of the fitting towards the projector and attach to the rear of the projector using M4 x 8 screws picture on the screen The picture is too small Slide towards the back the position of projection rises The picture is too large Slide towards the front the position of projection lowers 4 Adjust the screen height so that the projected image in the vertical direc tion fits on the screen Holding the screen s lateral bar loosen the left and right height adjustment knobs by turning them counterclockwise 2 Adjust the height of the screen holding it with both hands near the height adjustment knobs keep it level as you raise or 2 Attach the wires to the plate in two places 1 Pass the wires through the holes in the2. NEC WT40SN 40 Panel Screen WT4O0OSN Assembly Instructions We greatly appreciate your purchase of this NEC WT40SN flat panel screen Read these instructions carefully to ensure proper assembly The WT40SN is a panel screen exclusively for use with mirror projection type projectors It can be used in combination with the separately sold dedicated projector stand to form a stand with integrated screen Mi Be sure to read this section before using e About the pictograms Pictograms are used in these assembly instructions and on the product to ensure proper safe use of the product and prevent injury to you and others as well as damage to property The pictograms and their meanings are described below Be sure to understand them fully before reading the instructions Failure to heed these indications and handling improperly could lead to physical WARNING accidents including death or major injury Failure to heed these indications and handling improperly could lead to physical Z CAUTION injury or damage to surrounding property Examples of pictograms A The A symbol urges caution including warnings A concrete description of the caution is indicated on the diagram S The symbol indicates actions that should not be performed A concrete description of the forbidden action is indicated on the diagram Q The symbol indicates instructions that must be performed A concrete description of the instruction is indica
3. dicated stand 2 2 When using the screen alone 09 This completes assembly of the panel screen Insert the screen unit s upper lock Fasten the bottom edge of the Attach the caps to the frames Attach the frames and plate to the dedi cated stand CAUTION Before mounting lock the dedicated stand s cast ers lower the top panel and tighten the height adjustment knobs securely so that the stand is sta ble Line up the panel screen fixing holes in the dedicated stand with the holes in the frames 2 Place the plate on the frames and fasten it to the dedi cated stand using the M6 x 35 screws The stands included with the panel screen are not used so store them in a safe place Panel screen fixing holes M6 x 35 screw Mount the plate and stands to the frames Line up the frames with the screw holes in the plate insert the M6 x 35 screws and fasten to the stands screw holes fitting into the frame and fasten temporarily with the height adjust ment knobs Fasten the screen unit at the position of the stoppers in the frame Height adjustment knob Frame bottom screen to the frames edge fitting Slide the lower lock fittings and line them up with the screw holes in the frame bottom edge fitting 2 Fasten using two M6 x 10 screws Insert the caps over the upper tips of the frames 2 Fasten them with the 3 x 10 screws The caps prevent the screen
4. e Dirt on the screen will Do not hang from the screen hook objects onto it or reduce the picture quality If the screen surface is dirty push it apply some neutral detergent dissolved in about 20 parts Do not climb onto the screen of water to a soft cloth and wipe off the dirt gently Do not place any objects other than the designated Avoid using benzene or thinner as they could mar the projector on the screen s plate surface Do not scratch the screen with metal objects etc The screen s surface is protected with an extremely hard coating but as a plastic material is used rubbing hard objects such as metal against it could scratch it When transporting the screen do so in the same pack aged conditions as when it was purchased to avoid scratches and damage WT40SN 0804K 01 Mi Checking the Package Contents Check that the following parts are included in the package Caps 2 Frames 2 S L A A se P 3 x 10 screws 2 S S GF M4 x 8 screws with washers 4 COOK CPP SK Ms x 50 screws 4 M6 x 35 screws 4 P PPF A A M6 x 10 screws 4 Height adjustment knobs 2 WE Assembling the Panel Screen 1 Mount the two lateral bars to the frames Slide the lower lock fittings to the approximate positions shown on the diagram and fasten them in place with the M5 x 50 screws Lateral bar Lower lock fitting Frame 2 1 When mounting to a separately sold de
5. plate 2 Fasten the wires to the plate s wire lock screw holes using M4 x 8 screws lower it 3 Tighten the left and right height adjustment knobs by turning them clockwise CAUTION Be sure to attach the projector using the wires to pre vent the projector from falling Wire hole Adjust the height carefully so that the CAUTION screen does not tip over You could be injured and the equipment damaged if the screen tips over 5 Use the projector s FOCUS and buttons to accurately adjust the focus If there is keystone trapezoidal distortion adjust using the orojector s feet i Fine adjusting the Projection Position This completes adjustment of the projection position When the projector is placed at the center of the plate the picture is projected at approximately the center of the screen Fine adjust the projection position so that the picture fits on the screen REMARKS The projection distance between the projector s rear panel and screen is E External View approximately 6 4 cm the height of the bottom edge of the screen between the projector s bottom panel and the screen s bottom edge is approximately 35 4 cm calculated values Units mm Preparations Project an image from the projector See the Installation and Connections and Projecting Images Basic Operation sections of the projector s user s manual for complete instructions on p
6. rojecting images 1 Place the projector parallel to the screen e Be sure to shorten the projector s feet The projected image 1085 w f 668 will be distorted if the projector is at an angle 345 476 2 Use the projector s FOCUS and buttons to adjust the focus Bi l Mi Specifications Screen gain 2 0 Suited viewing range 45 1 2 screen gain Effective screen dimensions 824 width x 618 height mm External dimensions 874 width x 476 depth x 1085 height mm Weight Approx 5 8 kg Specifications and design subject to change without notice NEC Display Solutions Ltd
7. ted on the diagram WARNING e Do not make any modifications Doing so could lead to Q accidents due to the screen falling e Keep magnetic recording media at least 10 cm away S The screen is attached to the board by magnet Placing magnetic tickets credit cards floppy discs video tapes cassette tapes or other magnetic recording media within 10 cm from the screen could lead to loss of or damage to the recorded data Do not apply adhesive tape or the like to the screen s surface If cellophane or other adhesive tape is acci dentally stuck on the screen surface peel it off carefully being sure that none of the adhesive remains If there is any adhesive on the screen surface wipe it off carefully using a neutral detergent NOTE e Heed the items below Q Failure to heed them could lead to the screen falling or e Do not place the screen in direct sunlight or other places tipping over resulting in injury or damage to the equip exposed to high temperatures in humid or dusty places ment or in places where it will be exposed to water or oil e Be sure to tighten the product s screws securely Failure Q to do so could lead to the screen falling resulting in injury or damage to the equipment S e Do not use the screen outdoors Wind could cause the S screen to tip over or fall resulting in injury or damage to the equipment NCAUTION Do not place on sloped surfaces or in unstable places Do not touch the screen surfac
Download Pdf Manuals
Related Search