52044679 RUSSELHOBBS(RHLF1) FRZ390 KAPAK
Contents
1. For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 24 Trouble Shooting Possible cause As soon as the The end of the water drain hose is too Set the water drain hose to an appliance fills with low for the machine appropriate height See page water water 11 discharges No water appears to No fault Water is in the unseen part of be in the drum the drum There are detergent Non dissolving particles of some Perform an additional rinsing residues on laundry detergents may remain undissolved cycle by setting your appliance and adhere to your laundry as white to Rinsing programme or spots clean the spots using a small brush Laundry has oily like The reason for these oily like stains are Apply laundry stain remover to stains on them due to oil cream or ointment that may affected area and repeat the have been on the laundry prior to the wash programme with a wash maximum amount of detergent Error Codes Checks to be carried out The start pause The door is not shut Check the door is the door of the appliance light blinks properly closed properly The program The water level in your Has the water faucet been turned on is ready light blinks machine is below the the mains water to the property on heating element Hard water areas build up of lime scale The pressure of your can cause bl2. 10cm In case of built in installation the distance between top of the washer and bottom of upper plate should be at least 3mm Drain Hose Laundry Tub approx 2cm Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 10 Installation Water drainage e The water outlet hose should be mounted at a height of minimum 60 cm maximum 80 cm from the ground The end of the water outlet hose can be fitted directly to the drainage hole on the back side of the washer When installing the outlet hose secure it with a string or tie extensions not included Never attempt to extend the water outlet hose by adding extra parts If the outlet hose is too long do not force it back into the washer This will cause abnormal noise and damage to the product Diagram below illustrates installation depending on water supply and waste outlet Do not insert drain hose more than10cm 100mm down the waste outlet pipe z 7 max 100 cm min 60cm ca 105 cm max 100 cm min 60 cm 4 4 Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 11 Installation Water e The appliance should be connected to the cold water mains using new hose sets Old hose sets
3. Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 9 Installation Feet adjustment e Adjust the level of washing machine by the adjustable feet Please check if there is a gap between the four adjustable feet and the floor If there is then adjust the level of the washing machine by turning the adjustable feet Make sure that the machine does not sway and that it is completely level After the adjustment is finished turn the fixing nuts up tightly so that the adjustment that has been made is fixed NOTE The machine should not sway and all the adjustable feet should touch the floor Location of the Washing Machine Check location where the appliance will be installed Make sure you have everything necessary for correct installation Do not place or store your appliance below 0 C 32 F to avoid any damage from freezing Do not place or store laundry products on top of the appliance at any times Install the appliance on a horizontal solid flat non slippery and tough floor Do not install onto a carpet If the appliance is installed on an unsuitable floor it could make considerable noise vibrate severely and cause a malfunction If the appliance is not level adjust the feet up or down for horizontal installation Never put cardboard wood or other materials under your machine to try and stabilise the unit Ventilation openings must not be obstructed Leave a space right amp left 2cm rear
4. inlet hose Manual Cap holder Liquid detergent apparatus Note The drawings in the book may vary from your washer model They are designed to show the different features of all models covered by this book Your model may not include all features The Front of the machine Control buttons Detergent draw Control Knob Door Pump filter Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 7 Before using your Appliance The Back of the machine Water inlet valve Transport bolts Remove all transit bolts before installation Outlet hose Power cable Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 8 Installation Before operating the washing machine remove the 4 transportation screws and rubber spacers from the back of the machine If the screws are not removed it may cause heavy vibration noise and product malfunction voiding the guarantee Unscrew the 4 screws with a wrench spanner or cross tip screwdriver Keep the four screws as they will need to be re used if the machine has to be transported Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday
5. r Ja Detergent can also accumulate inside the recess which should be cleaned occasionally with a brush Once you have finished cleaning replace the case and run a rinse cycle without laundry i 5 J i laa Do not wash your detergent drawer in a dishwasher Appliance specifications may vary depending on the product purchased Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 30 Maintenance Flush stopper Remove the detergent drawer Disassemble the flush stopper and clean the softener residues completely Refit the flush stopper after cleaning Check that the flush stopper is correctly positioned after replacing Flush stopper Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at Www productcareuk com 31 Stain Removal Information Fruit Stretch the stained area and pour on cold water Apply glycerine and wipe over the stain Wait 1 2 hours and rinse after wiping the stained area with a few drops of white vinegar Grass stain Rub over the stained area with detergent before washing Oil based paint Immediately apply paint thinner solvent over the stained area before it dries then rub the area with detergent and wash Burn stain If your
6. adults in line with the information provided in this user s manual Your machine is designed to be used domestically Commercial use will cause your warranty to be cancelled Anyone s intervention to your machine except for a qualified engineer in anyway will cause your warranty to be invalid Ideal operating temperature of your machine is 15 25 C Do not place your machine on carpet as this will block ventilation of the base Do not keep inflammable liquids near your machine You should remove the transport bolts of your machine before the first usage Faults occurring in machines operated with transport bolts fitted are not covered by the warranty Do not put the discharging hose of your machine in a bucket or sink Your machine is not covered under warranty for faults caused by any kind of external factors pesticides fire etc To avoid fire electrical shock and other accidents please remember the following To ensure your safety an earthed power supply should be used e Only the voltage indicated in power label can be used If you are not clear of the voltage at home please contact your electricity supplier amp Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 4 Product Fiche Brand Russell Hobbs Model RH1042 B Rated capacity 5 0kg Energy efficiency class A Wa
7. laundry is suitable for applying bleacher you can add bleacher into washing water For wool fabric a cloth previously submerged in oxygen water should be used to dampened the area of the stain Using a dry cloth cover the area and iron over It should be washed after being rinsed properly Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 32 Stain Removal Information Alcoholic drinks Wash the stained area under cold water wipe with glycerine then rinse with a solution of water and white vinegar Shoe polish Scratch out the stain taking care not to damage the material rub over the stained area with a solution of detergent and water and rinse Tea and coffee Stretch the area containing the stain and pour on hot water Care should be taken when performing this procedure Chocolate and cocoa Leave your in cold water and rub the stained area with detergent then wash at a high temperature Tomato paste Scrape away the dried pieces leave to soak in cold water for about 30 minutes and hand wash by rubbing with detergent Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 33 Stain Removal Information Blood stain Leave to soak in cold wa
8. should not be reused In using only one water tap or in case of only one water inlet valve connect the inlet hose to the cold water inlet valve Water inlet hose connection Be careful not to confuse hot water inlet and cold water inlet Your machine has a single water cold inlet To prevent leakages on the connection joints 1 seal is included in the hose packing After all connections are completed check for leakages around the connection joints by turning on your tap completely and seeing if any water escapes Be sure that the water inlet hoses are not folded twisted crushed or elongated by stretching Electrical connection e Your washing machine is set to 220 240V and 50Hz e The mains cord of your washing machine is equipped with a specific earthed plug This plug should always be inserted to a earthed socket of 13 amps The current value of the fuse should be 13 amps We do not take responsibility for any damage that occurs due to non earthed usage Operating your appliance under low voltage will cause the life cycle of your appliance to be reduced and its performance to be restricted amp Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 12 Installation Ordinary tap not included 1 Pull down the collar of 2 Loosen the four screws 3 Fit the water tap adapter the inlet hose
9. the water supplier to the washer This helps avoid accidental flooding due to a water pressure surge while you are away Cleaning the water inlet filter Filters are used to avoid dirt and foreign substances in the water from entering the machine These are on the tap and on the ends of water valves along the water inlet hose of your machine If your machine cannot take sufficient amounts of water despite the tap being open these filters should be cleaned Detach the water inlet hoses Remove the filters on water inlet valves using pliers and then clean it with a brush in water Disassemble the filters on the tap end of the water inlet hoses manually and clean it Having the filters cleaned you can fit them in the same way reversely Filters of water inlet valves may be clogged due to a contaminated water tap lack of necessary maintenance or valves may be broken Which will cause water to leak into your machine continuously Breakdowns or faults that may arise because of these reasons are not covered under manufacturer s guarantee Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 28 Maintenance e Please Note Unplug the appliance before cleaning the filter for your own safety Cleaning the drain filter e This drain filter is used to screen foreign objects such as threads coins pins
10. to separate in the water tap into the water tap and it from the water tap tighten the four screws adapter evenly while pushing up the adapter so that the rubber packing can attach to the water tap tightly f gt 4 Remove the tape and 5 Connect the inlet hose to 6 Connect the inlet hose screw connector B into the water tap adapter by adapter of the hose to connector A tightly pulling down the collar of the water inlet of the the hose end washing machine by turning it clockwise to be fixed tightly d Connector A a 2 Connector B fa Please check the rubber f packing inside the inlet hose adapter of the hose Screw shaped tap not included 1 Connect the inlet hose to 2 Connect the connector 3 Insert the inlet hose the water tap by inlet supplied if adapter into the water screwing the connector necessary inlet of a washing tightly machine and turn it to be gntly A CA Connector 9 inlet RUDDE a Connector J Pei OA 4 Hose Connector Hose Connector Check the packing in the inlet amp Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 13 Control Panel y Q Russell Hobbs 6 Cold wash Start Pause cycle Programme Cotton 90 C Cotton 60 C With prewash Cotton 60 C Cotton 40 C Eco wash Quick wash Cotton cold Synthe
11. 50 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 23 Trouble Shooting Your appliance does not fill with water Excess foam has formed in the detergent draw Unsatisfactory washing results Possible cause Water tap has been turned off Water inlet hose may be twisted Water inlet hose clogged Valve inlet filter clogged The machine door is not completely closed Excessive amount of detergent used Wrong detergent used The dirtiness of the laundry does not match the programme select Insufficient amount of detergent used The washing machine is overloaded with laundry Q Russell Hobbs Turn the faucet on Check water inlet hose and untwist Clean water inlet hose filters Clean the valve inlet filters Close the machine door Press the Start pause button To eliminate foam formation mix a tablespoon of softener with 500ml of water and pour the mixture in the detergent drawer After 5 10 minutes press the Start pause button again For the next washing operation use the correct amount of detergent Use detergents produced only for automatic washing machines Select the appropriate programme for the dirtiness of the laundry See page 21 Adjust the amount of detergent based on the dirt level of the laundry Load the washing machine with the correct amount and weight and do not exceed maximum laundry capacity
12. Washing Machine Instruction Manual Model number RH1042 B For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com IMPORTANT 1 Before using your appliance please read this Ut manual carefully and keep it for future reference Contents Safety Instructions Product Fiche Savings amp Efficiency Information Before using the Appliance Installation Control panel How to Use Program Table First Wash Trouble Shooting Error Codes Maintenance Stain Removal Information Specification Connection to the Mains Supply Warranty Notes amp Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com Safety Instructions Important note l Please read this booklet before installing and switching on this appliance The manufacturer assumes no responsibility for incorrect installation and usage as described in this booklet This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the applia
13. buttons etc e f the drain filter is not cleaned regularly after every 10 times of use a drain problem could be caused e Depress the lug downwardly to uncover the pump section of the toe board and pull it towards yourself and extract it CAUTION Be careful when draining if the water is hot Before opening the filter cover place a towel on the ground immediately in front of the filter hole to soak up remaining water Loosen the filter cover in and allow water to flow out Clean the foreign objects present in the filter Check whether the pump rotates with your hands After cleaning the filter fit the filter cover by rotating it clockwise Fit the pump section of the toe board Remember that water will leak if you do not fit the filter cover properly Appliance specifications may vary depending on the product purchased Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 29 Maintenance Cleaning the detergent case e After a while detergent and fabric softeners leave a deposit in the case e It should be cleaned from time to time with a jet of running water If necessary it can be removed completely from the machine by pressing the catch downwards and by pulling it out To facilitate cleaning the upper part flush stopper of the fabric softener compartment can be removed pur
14. chine has developed can be solved with the help of the below Your appliance does not discharge water Your appliance vibrates Your appliance does not start Possible cause Outlet hose is clogged or twisted Pump filter clogged Laundry settled in the machine unevenly The feet of your machine have not been adjusted correctly Transportation screws have not been removed Your machine is under loaded with laundry or laundry settled unevenly Your machine is overloaded with laundry or laundry settled unevenly Your machine rests on a hard surface It is not plugged in The fuse has blown Electricity cut off Start pause button not pressed Programme dial stop position The machine door is not completely closed Q Russell Hobbs Check the outlet hose then either clean or untwist Clean the pump filter Spread your laundry in the machine evenly Adjust the feet on your machine Remove transportation screws This will not stop the operation of your machine Do not overload the appliance more than the amount recommended and settle the laundry in the machine evenly Prevent your machine from resting on hard surfaces sides and rear Plug the machine in Replace the fuse Check mains power Press the Start pause button Switch the programme dial to the desired position Close the machine door For Customer Services amp Spare Parts please call 0345 208 87
15. correct amount of detergent compartment of the detergent drawer The Pre wash feature might be used for your very dirty laundry If you are going to do a pre wash place 1 4 of the detergent you would normally put in the detergent compartment into the pre wash compartment numbered 1 and put the remaining 3 4 to the detergent compartment numbered 2 Use detergents produced for automatic washing machines in your machine Adhere to the advice of detergent manufacturers while determining the amount of detergent you should use with your laundry The higher the degree of hardness of the water the more detergent you will need to use Put the softener in the softener compartment in the detergent drawer Do not exceed the 200 mark level Otherwise softener will flow into washing water through flushing Softeners with high density are required to be thinned out to a degree before being put in the drawer High density softener will clog the flush and block the flow of the softener When using liquid detergent use the liquid detergent apparatus supplied with the appliance You can use liquid detergent for all programs without pre wash For this inserted the liquid detergent apparatus into the groves located in the main detergent compartment Add the correct amount of liquid detergent as directed by the detergent manufacturers Do not exceed the 200mm level mark as indicated on the apparatus Remove the liquid detergent apparatus if reverting back to powder de
16. d for G2S Limited Hindley Green Wigan England WN2 4EZ amp Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 37 amp Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 38 amp Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at Wwww productcareuk com 39 For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm Or visit us at www productcareuk com Revision 4 CE pid This symbol is known as the Crossed out wheelie bin Symbol When this symbol is marked on a product batteries it means that the product batteries should not be disposed of with your general household waste Only discard electrical electronic battery items in separate collection schemes which cater for the recovery and recycling of materials contained within Your co operation is vital to make sure the success of these schemes and for the protection of the environment For your nearest disposal facility visit www recycle more co uk or ask in store for details We reserve the right due
17. e outside of the washer to keep it looking like new Interior Clean interior with 250ml of chlorine bleach mixed with 500ml of detergent Run washer through a complete cycle Repeat this process if necessary Important note Do not put sharp or metal object in your washer or they can damage the finish Check all pockets for pins clips money bolts nuts etc Do not lay these objects in your washer after emptying pockets Winter storage or moving care Install and store your washer where it will not freeze Because some water may stay in the hoses freezing can damage your washer If you store or move your washer during freezing weather winterize it To winterize washer e Turn off water faucet e Disconnect and drain water inlet hoses e Run washer on a drain and spin setting for 1 minute e Unplug the power supply cord To use washer again e Flush water pipes and hoses e Reconnect water inlet hoses e Turn on water faucet e Reconnect the power supply cord amp Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at Wwww productcareuk com 2 Maintenance Non use or vacation care Operate your washer only when you are at home If you are on vacation or don t use your washer for an extended period of time you should e Unplug the power supply cord or turn off electrical power to the washer e Turn off
18. ere to the manufacturers advice regarding the use of fabric conditioner or similar products you will use in your machine Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 19 How to Use Placing laundry into the machine Open the loading door of your appliance Check inside the drum of your machine There might be laundry left inside from previous washes If there is empty your machine before selecting your program Place your laundry into the machine by spreading them well Fold objects like quilts and blankets that you will load into the machine as shown below NB Do not exceed the maximum laundry weight of 5kg Appliance specifications may vary depending on the product purchased Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 20 How to Use Programme Max dry load capacity kg Type of laundry Programme times min COTTON90 C COTTON 60 C Prewash Slightly dirty cotton coloured and linen textile COTTON COLD 5 Slightly dirty cotton coloured and linen textile Washed without heating the tap water Dirty cotton and linen textile Very dirty cotton coloured and linen textile Dirty cotton coloured and linen tex
19. ing the Start Pause button Changing the programme If you have selected a programme and you want to continue with another Press the Start Pause button Bring the program knob to the O off position Adjust the programme knob to the programme you desire The programme ready light will be on By pressing the Start Pause button run the programme which you have selected Cancellation of the Programme To end a programme early e Press the Start Pause button Turn the programme knob to O off position Turn the programme knob to Draining or Spinning programme The programme ready light will be on Run the programme you have selected by pressing the start pause button End of programme Your machine will automatically stop when the programme you have selected ends e The programme end light will be on amp Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 16 How to Use Detergent drawer general view Your appliance is designed to use both powder and liquid detergent When using liquid detergent use the liquid detergent apparatus supplied with the appliance You can use liquid detergent for all programs without pre wash For this inserted the liquid detergent apparatus into the slots located in the main detergent compartment Add the correct amount of liquid detergent as directed by
20. must be connected to the terminal marked with the letter N or coloured BLACK The BROWN wire is the LIVE wire and must be connected to the terminal marked with the letter L or coloured RED Always ensure that the plug cord grip is fastened correctly DANGER Electric If a 13A BS1363 fused plug is used it must be fitted with a Shock Risk 13amp fuse conforming to BS1362 and be BSI or ASTA approved INSIDE VIEW FUSE EARTH _ _ YELLOW GREEN NEUTRAL BLUE CORD GRIP Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 36 Warranty This product is guaranteed for 12 months from the date of the original purchase If any defect arises due to faulty materials or workmanship the faulty product must be returned to the place of purchase Refund or replacement is at the discretion of the retailer The following conditions apply e The product must be returned to the retailer with the original proof of purchase The product must be installed and used in accordance with the instructions contained in this instruction guide and any other instructions for use which are supplied It must be used for domestic purposes only and for its intended use This warranty does not cover wear and tear damage misuse or consumable parts This does not affect your statutory rights Produce
21. nal function selection voltage fluctuations It will reduce energy and water consumption when used with the laundry Capacity proposed for the selected programme Wash your less dirty or daily laundries in short programmes Carry out cleaning and maintenance periodically use your machine in convenient time intervals specified by electricity vendor Care label GraphicSymbol Illustration Graphic Symbol Illustration No Machine Wash Do not Wash No Dry Clean NoVWing No Bleach Do not Tumble Dry Do not Iron Iron with Cloth Dry after Wash ity Hand Wash Weshing nduding Machine Wash and Hand Wash Dry Clean Warmly Dry Clean Bleach Tumble dry Iron O gt pog p D my D Steam Iron A j Medium Tempers ture and mie Mex Temperature 150 C a TT Line Dry b O pD pE By amp e Eee Line Dry in Shade Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 6 Before using your Appliance e Transportation screws which are located at the back of the machine must be removed before using or running the machine You will void the manufacturer s guarantee if these are not removed before using or running the machine Before installation check that all parts listed below are present If any parts are missing please contact the product care service team on 0345 208 8750
22. nce Do not use an extension lead for this appliance Only plug directly into a wall socket Do not plug in damaged plug sockets In case the power cable becomes damaged contact Customer Services on 0345 208 8750 for advice Never pull the cable when unplugging always grip the plug itself Do not plug in or pull out the plug from the receptacle with wet hands to prevent electric shock Never touch the machine with wet hands or feet Never open the detergent drawer when the appliance is running Never force the door to open when the washing machine is running Do not touch discharging hose and water during discharging as the appliance may reach high temperatures when running In case of any breakdown unplug the appliance first and then turn the tap off Do not attempt to repair by yourself always contact Customer Services on 0345 208 8750 for advice Remember that packaging materials of your machine may be dangerous for children Keep the packaging materials in a place where children cannot reach or dispose of them appropriately Do not allow your children to play with the washing machine as it is an electrically driven appliance Keep your pets away from your machine amp Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 3 Safety Instructions Your appliance should only be used by
23. ockages in inlet hose filter water supply may be low valve internal pipes and water or switched off distribution plate Err 03 The start pause The pump has failed or Clean the pump filter light and program the pump filter is ready light blinks obstructed Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 25 Error Codes Checks to be carried out The program end Communication error Switch the appliance off and unplug from the light blinks wall socket Leave the appliance for 2 minutes so that it can discharge Insert the plug back in the wall socket turn on the appliance select the desired programme and press start Has the appliance started its programme The start pause The heating element of Hard water areas build up of lime scale can light and your machine or the cause blockages in inlet hose filter valve program end heat sensor has failed internal pipes and water distribution plate light blink The program The motor has failed Turn off the appliance ready light and program end light blink The program Configuration error Switch the appliance off and unplug from the start pause light wall socket Leave the appliance for 2 ready light and minutes so that it can discharge Insert the program end plug back in the wall socket turn on the light stays on appliance selec
24. otton programmes at 60 C and 40 C at full load and partial load and the consumption of the low power modes Actual energy consumption will depend on how the appliance is used Based on 220 standard washing cycles for cotton programmes at 60 C and 40 C at full load and partial load Actual water consumption will depend on how the appliance is used Based on test results of standard 60 C cotton programme at full load and partial load and standard 40 C cotton programme at partial load Program duration energy consumption and water consumption values may vary according to wash load weight and type selected extra functions tap water and ambient temperature Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 5 Savings amp Efficiency Information Some important information to get more efficiency out of your appliance The amount of laundry you put in your washing machine should not exceed the maximum amount indicated in the programme table By avoiding overloading your machine should run more efficiently Not using the pre wash feature for normal and lightly soiled laundry should save electricity and water Describing Energy label and Saving energy Energy and water consumption may vary based on water pressure water hardness water temperature ambient temperature laundry amount additio
25. rts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 15 How to Use Child Lock Child lock is used in order to protect the washing cycle from the effects of unwanted button activations during the cycle The Child lock is activated by pressing the first and third button on the control panel at the same for more than 3 seconds When child lock is activated LEDs on the cold wash and no spin buttons will blink to indicate that Child Lock is active In order to De activate Child Lock the same buttons 1st and 3rd should be pressed again for more than 3 seconds Deactivation of Child Lock is shown by blinking of the LED on the cold wash and no spin buttonsbutton Whilst the child lock is active all operations become inactive except for the dial number 0 which stops the cycle however if the dial is returned to the current setting number and started the programme will continue as normal Running the machine Program selection and features Select an appropriate programme for your clothing by turning the main knob Start Pause By pressing this button you can start the programme you have selected or pause a running programme Starting the programme e Adjust the programme knob to the programme you desire e The programme ready light will be on e lf you want you can select one or more additional functions e Run the programme which you have selected by press
26. shing performance class A A Higher G Lower Rated capacity Cotton 60 full load kg 5 0 Energy efficiency class A Energy consumption kWh annum 167 Water consumption L annum 9240 Spin drying efficiency class C Noise Washing dB A 58 Noise Spinning dB A 77 Max spin speed rpm 1000 Remaining moisture content 62 Energy consumption cotton 60 full load kWh cycle 0 85 Energy consumption cotton 60 partial load kWh cycle 0 66 Energy consumption cotton 40 partial load kWh cycle 0 52 Water consumption Cotton 60 full load L cycle 43 Water consumption Cotton 60 partial load L cycle 41 Water consumption Cotton 40 partial load L cycle 41 Power consumption off mode W 1 00 Power consumption left on mode W 2 00 Program duration min cotton 60 full load 190 Program duration min cotton 60 partial load 145 Program duration min cotton 40 partial load 140 Note e Programme number 3 Standard 60 C cotton programme and programme number 4 standard 40 C cotton programme are the standard washing programmes to which the information on the label and the fiche relates that these programmes are suitable to clean normally soiled cotton laundry and that they are the most efficient programmes in terms of combined energy and water consumptions The actual water temperature may differ from the declared cycle temperature Based on 220 standard washing cycles for c
27. t the desired programme and permanently press start Has the appliance started its programme The start pause Fault error Switch the appliance off and unplug from the light program wall socket Leave the appliance for 2 ready light and minutes so that it can discharge Insert the program end plug back in the wall socket turn on the light blink appliance select the desired programme and press start Has the appliance started its programme The program The network voltage is If the network voltage is lower than 150V or ready light and too high or too low higher than 260V your machine will program end automatically stop When the network light stays on voltage is recovered your machine will permanently continue its operation All repairs to your machine should be carried out by a qualified engineer or contact Product Care on 0345 208 8750 Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 26 Maintenance The correct care of your appliance can extend its life This section explains how to care for your washer properly and safely When cleaning your machine ensure that the machine is unplugged and the water supply is closed off Cleaning your Machine Exterior Wipe up detergent bleach and other spills with a soft damp cloth or sponge as and when they occur Occasionally wipe th
28. ter for about 30 minutes and hand wash with detergent Cream ice cream and milk Leave to soak in cold water for about 30 minutes and hand wash with detergent Mould Clean the stained area as soon as possible and hand wash with detergent Ink Hold the stained area under cold running water and wait until the inky water has completely run off Rub the stained area with a solution of lemon juice and water leave for 5 minutes before washing Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 34 Specification Maximum washing capacity dry laundry kg Water pressure Mpa Maximum 1 Minimum 0 1 Dimensions HxWxL mm 845x597x527 amp Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at Www productcareuk com 35 Connection to the Mains Supply For UK use only Plug fitting details where applicable As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The GREEN YELLOW wire is the EARTH and must be connected to the terminal which is marked with the letter E or by the earth symbol or coloured GREEN or GREEN YELLOW The BLUE wire is the NEUTRAL and
29. tergent see page 17 amp Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at Www productcareuk com 18 How to Use Loading clothes for washing e Drop items into the appliance loosely Items should move easily through wash water for the best cleaning and wrinkle free results e Load appliance properly e You should not load your appliance with an amount of laundry that will exceed the maximum laundry amount specified for this appliance Overloading and selecting a inappropriate program for the wash load can e Cause poor cleaning Increase wrinkling Create excessive lint e Wear out items faster because of pilling Mix large and small items in each load Load evenly to maintain washer balance An unbalanced load can make the appliance vibrate and prolong program times during spin e Ensure that no laundry is caught between the cover and below the seal when closing the door of your appliance When closing the door push the door of your appliance until you hear the locking sound this indicates the door is fully closed In case of any malfunction unplug the machine and close the tap first Do not attempt to repair by yourself and contact Customer services on 0345 208 8750 Never open the detergent compartment when the appliance is running Never force the door open when the machine is running Please adh
30. the detergent manufacturers Do not exceed the 200 level mark as indicated on the apparatus Remove the liquid detergent apparatus if reverting back to powder detergent Main wash detergent compartment In this compartment use only substances like detergent Slots for liquid liquid or powder or anti lime You can find detergent apparatus the liquid detergent apparatus for your liquid detergent inside your machine Softener starching compartment In this compartment substances like softener for your laundry can be used it is advised that you use amounts as directed on the softener label If the softener is of a thick constituency dilute with a small amount of water If the softener is to thick it will struggle to siphon on the rinsing cycle Pre Wash detergent compartment This compartment should only be used when the pre wash feature is selected It is recommended that the pre wash feature is used only for very dirty laundry Liquid detergent apparatus Q Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 17 How to Use Choice of detergent and placing into the machine The amount of detergent you will put in your machine will depend on the following criteria The amount of detergent needed is based on how dirty the laundry is Do not prewash your less stained laundries and put the
31. tic 60 C Synthetic 40 C Synthetic Cold Delicate 30 C Wool 30 C Rinse Spin Drain O Off DRAIN SPIN RINSE ee aa a e e e O m Da amp Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at Www productcareuk com 14 How to Use To obtain the best washing results you must operate your appliance properly This section gives you this important information Preparing clothes for washing e Close zippers snaps and hooks to avoid snagging on other items Remove pin buckles and other hard objects to avoid scratching the washer interior Empty pockets and pull them inside out Turn down cuffs and turn synthetic knits inside out to avoid pilling Reverse textiles such as pants knitwear t shirt and sweat suits Tie strings and sashes to avoid tangling Treat spots and stains See Removing stains section pg32 pg34 Follow the washing instructions supplied on the clothing Important note Faults that emerge due to the penetration of foreign objects will void the manufacturer s guarantee Separate heavily soiled items from lightly soiled ones even if they would normally be washed together Separate dark colours from light colours colourfast items from non colourfast items Wash lint producers and lint collectors separately Q Russell Hobbs For Customer Services amp Spare Pa
32. tile Dirty cotton coloured and linen textile Dirty cotton coloured and linen textile SYNTHETICS 60 C Dirty synthetic or synthetic mixture textile SYNTHETICS 40 C SYNTHETICS COLD Slightly dirty synthetic or synthetic mixture sensitive laundry Washed without heating the tap water Slightly dirty cotton coloured synthetic or synthetic mixture sensitive laundry DEL CATE 30 C WOOL 30 C RINSE When you need an additional rinsing to be done to your clothes after the process you can use this programme for all kinds of clothes SPIN When you need an additional spinning to be done to your clothes after the washing process you can use this programme for all kinds of clothes DRAIN This programme is used to drain the dirty water inside after the washing process of your machine If you want the water inside your machine to be drained before the programme ends you can use this programme amp Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at www productcareuk com 21 Dirty hand and machine to wash wool laundry Slightly dirty synthetic or synthetic mixture textile First Wash Before using the appliance for laundry ensure you run the machine on a program of 90 C Cotton program with detergent and without laundry Before Use Ensure the inlet hose is connected correctly and
33. to possible changes to design to alter the instruction manual without prior notice Q Russell Hobbs
34. turn the inlet valve from its closed position to the open position Check that the outlet hose is connected correctly Plug in the machine to the power socket Run the machine on a cycle of 90 C Cotton program with detergent and without laundry After cycle has completed the appliance is ready for use Important note If the supply power is turned off at any stage of the washing program and then turned on your machine will continue the program from the point where it was interrupted This is not harmful for your machine Recommendations e Put detergent into the drawer at the beginning of each wash e It is recommended that you wash only extremely dirty laundry in prewashing programme e The amount of laundry you put in your washing machine should not exceed 5kg If your machine is not going to be used for a long period of time you should unplug the appliance turn off the water inlet and leave the door slightly open This is so that the inside of your machine will remain dry and will not cause an unpleasant odour amp Russell Hobbs For Customer Services amp Spare Parts please call 0345 208 8750 Opening times Monday Friday 8am 6pm amp Saturday 9am 1pm or visit us at Wwww productcareuk com 22 Trouble Shooting All repairs to your machine should be carried out by a qualified engineer or contact Product Care on 0345 208 8750 Before contacting a qualified engineer or Product Care please see if the problem your ma
Download Pdf Manuals
Related Search