WS5000 Series - Motorola Solutions
Contents
1. 28 WS5000 Series WS5100 Installation Guide Statement of Compliance Symbol Technologies Inc hereby declares that this device is in compliance with all the applicable Directives 89 336 EEC 73 23 EEC A Declaration of Conformity may be obtained from http www2 symbol com doc Part Numbers Support and Sales 10 Part Numbers Support and Sales Part Numbers Description Part Number 6 port WS5100 Wireless Switch WS 5100 R210 06 WR 12 port WS5100 Wireless Switch WS 5100 R210 12 WR 18 port WS5100 Wireless Switch WS 5100 R210 18 WR 24 port WS5100 Wireless Switch WS 5100 R210 24 WR 30 port WS5100 Wireless Switch WS 5100 R210 30 WR 36 port WS5100 Wireless Switch WS 5100 R210 36 WR 42 port WS5100 Wireless Switch WS 5100 R210 42 WR 48 port WS5100 Wireless Switch WS 5100 R210 48 WR Redundant WS5100 Wireless Switch WS 5100 R210 RS WR 6 port Upgrade WS 5100 UC WW Symbol Support Center Use the Symbol Support Center as the primary contact for any technical problem question or support issue involving Symbol products Symbol Support Center responds to calls by email telephone or fax within the time limits set forth in individual contractual agreements Telephone North America 1 800 653 5350 Telephone International 1 63 1 738 6213 Fax 631 738 5410 Email support symbol com When contacting Symbol Support Center please provide the following information e Serial num2. Event Top LED Bottom LED POST failed critical error Red blinking Red blinking Software initialization failed Amber solid Off Country code not configured wil remain in this state until the country Amber Sold Amber blinking code is configured No access ports have been adopted Blue blinking Amber blinking Primary inactive or failed Amber blinking Blue blinking 5 6 WS5000 Series WS5100 Installation Guide 3 Hardware Setup 3 1 Installing the WS5100 To install the WS5100 switch in a rack 1 Attach the rack brackets to the sides of the device The rack brackets are ambidextrous 2 Attach the brackets to the rack 3 2 Adding the WS5100 to the Network The WS5100 fits in the distribution layer of the existing wired network and must have OSI Layer 2 connectivity with the access ports it needs to adopt The following illustration shows the major components of a WS5100 network deployment Terminal Emulation i VT 100 19200 bps 8 data bits 1 stop bit No parity No flow control Console Cable included to Console Port WS 5100 Eth1 Eth2 Hardware Setup Layer 2 lt SwitchA Ld a POE Wireless Clients Layer 2 Switch B Wired Computer As shown in the illustration all wireless devices are connected to the WS5100 through LAN Switch A and all wi
3. Type Data PSP PowerMod CAM mode MAC Address 00 A0 F6 43 AA 6B Interface RF IP Address 192 168 123 103 Association Uptime 1009 seconds WLAN QSG First WLAN Session Tkt Expirec 0 RF State Associated Session Username Authentication St Authenticated Packets Sent 20 Authentication Mett Open Packets Received 87 Encryption Metho Open Bytes Sent 15752 Access Part 00 A0 F6 56 0F 00 Bytes Received 17611 Current Tx Rate 11 Mbps Last Activity 0 Supported Rates 1 2 5 5 11 Mbps VLAN ID Not using VLAN RSSI 42 i Close Help Warning Applet VVindow 7 Finally verify the WS5100 is fully operational on both sides of the network wired and wireless by pinging the device on the wired LAN from the MU If the wired device responds the switch is working If it doesn t respond make sure the wired device is on it s on the proper LAN and you re pinging the correct IP address or host name 23 24 WS5000 Series WS5100 Installation Guide 7 Shutting Down the WS5100 To gracefully shutdown the WS5100 issue the shutdown command from the configure context in the CLI WS5000 Cfg gt shutdown This command will halt the system Amanual power cyclewillberequiredtore starttheswitch Do you want to proceed yes no yes System shut down might take a fewmins Shutting down the switch Shutting down dhcp daemon done Shutting down apache server in the OPEN mode done Shutting down cell controll
4. The prompt changes when you change contexts ws5000 gt configure ws5000 Cfg gt All of the contexts in the following instructions are subcontexts of the configure context For example to get to the WLAN context you would type wlan within the configure context ws5000 Cfg gt wlan ws5000 Cfg WLAN gt As a shortcut jump directly to a configuration subcontext through the configure subcontext command ws5000 gt configure wlan ws5000 Cfg WLAN gt As a further shortcut the CLI performs silent auto completion of unambiguous commands As an example con is a sufficient abbreviation for configure If you enter an abbreviated command that isn t unambiguous i e that can resolve to more than one command you ll be presented with a list of command completions NOTE All CLI commands are case insensitive All user created data the name you give a policy that you create for example is case sensitive 8 2 Common CLI Commands Within any context you can e List all the available commands by typing help or e Show the current configuration settings by typing show Bump up one configuration context level by typing two periods e Get back to the top level context by typing exit Regulatory Information 27 9 Regulatory Information WARNING This regulatory section applies only to the WS5100 device WS 5100 Rxx xxx WR For more details refer to Part Numbers Support an
5. 9 10 WS5000 Series WS5100 Installation Guide 4 Preliminary Configuration through the CLI Most of the practical configuration of the WS5100 is performed through the Quick Start View applet However to access the applet you first have to use the Command Line Interface CLI to configure the Ethernet port that connects the switch to the wired LAN Before proceeding with the CLI instructions described below connect a configuration computer to the WS5100 as described in Adding the WS5100 to the Network on page 6 Keep in mind the switch doesn t have to be deployed into the network to perform this initial configuration 4 1 Typographical Conventions The following typographical conventions apply to the CLI examples e The CLI prompt and output are shown as unbolded e Text that you enter verbatim is bold e Values that you make up as command parameters are in bold italics For example ws5000 Cfg Ethernet 2 gt set gateway w x y z Here everything up to and including the gt is part of the CLI prompt set gateway is a CLI command w x y z is a value you create or otherwise obtain as appropriate for your network 4 2 Logging Into the CLI After you ve connected the WS5100 through the serial port and powered on the switch the terminal emulation window displays a series of inscrutable diagnostic messages which you can ignore after which it will display the WS5000 Series user name prompt Use the na
6. Symbol and the Symbol logo are registered trademarks of Symbol Technologies Inc Patents This product is covered by one or more of the U S and foreign patents listed at http www symbol com patents Symbol Technologies Inc One Symbol Plaza Holtsville New York 11742 1300 http www symbol com Introduction 1 Introduction The Symbol WS5100 Wireless Switch is the high performance member of Symbol s WS5000 Series family The WS5100 which is built on the same award winning hardware and software architecture as the WS5000 platform provides centralized Wireless LAN WLAN configuration and management by coalescing the network intelligence that was previously spread across physically distributed access points By replacing access points with simpler access ports or thin access points the WS5100 becomes the single point of contact with the WLAN thus reducing the complexity of wireless networking by moving management out of the ceiling and into the wiring closet In addition through the use of Symbol s patented Virtual AP architecture the WS5100 lets you create multiple WLANs without changing or adding to the existing wired network infrastructure This document is written for the network device installer 1 1 Package Contents Inspect the package contents and report any missing or damaged items to your sales representative The package should contain the following e WS5100 Wireless Switch e WS5100 Installation
7. may be required to take adequate measures Symbol Technologies Inc End User License Agreement 11 Symbol Technologies Inc End User License Agreement BY DOWNLOADING INSTALLING OR USING THE SOFTWARE DESCRIBED IN THIS DOCUMENT YOU OR THE ENTITY OR COMPANY THAT YOU REPRESENT LICENSEE ARE UNCONDITIONALLY CONSENTING TO BE BOUND BY AND ARE BECOMING A PARTY TO THIS LICENSE AGREEMENT AGREEMENT LICENSEE S USE OR CONTINUED USE OF THE DOWNLOADED OR INSTALLED MATERIALS SHALL ALSO CONSTITUTE ASSENT TO THE TERMS OF THIS AGREEMENT IF LICENSEE DOES NOT UNCONDITIONALLY AGREE TO ALL OF THE TERMS OF THIS AGREEMENT DO NOT CONTINUTE THE INSTALLATION PROCESS IF THESE TERMS ARE CONSIDERED AN OFFER ACCEPTANCE IS EXPRESSLY LIMITED TO AND EXPRESSLY CONTINGENT UPON THESE TERMS IF YOU ARE ACCEPTING THESE TERMS ON BEHALF OF A COMPANY ANOTHER PERSON OR ANY OTHER LEGAL ENTITY YOU REPRESENT AND WARRANT THAT YOU HAVE THE AUTHORITY TO BIND THAT COMPANY PERSON OR ENTITY 1 LICENSE GRANT Subject to the terms of this Agreement Symbol Technologies Inc and or its subsidiaries Licensor hereby grants Licensee a limited personal non sublicensable non transferable nonexclusive license to use the software that Licensee is about to download or install and the documentation that accompanies it collectively the Software for Licensee s personal use in connection with hardware produced by Licensor and only in accordance with the accompanying documenta
8. not give Licensee any rights not expressly granted herein 3 INTELLECTUAL PROPERTY CONTENT All title and intellectual property rights in and to the Software including but not limited to any images photographs animations video audio music text and applets incorporated into the Software and any copies you are permitted to make 31 32 WS5000 Series WS5100 Installation Guide herein are owned by Licensor or its suppliers All title and intellectual property rights in and to the content which may be accessed through use of the Software is the property of the respective content owner and may be protected by applicable copyright or other intellectual property laws and treaties This EULA grants you no rights to use such content As a condition to Licensee s use of the Software Licensee represents warrants and covenants that Licensee will not use the Software i to infringe the intellectual property rights or proprietary rights or rights of publicity or privacy of any third party ii to violate any applicable law statute ordinance or regulation iii to disseminate information or materials in any form or format Content that are harmful threatening abusive harassing tortuous defamatory vulgar obscene libelous or otherwise objectionable or iv to disseminate any software viruses or any other computer code files or programs that may interrupt destroy or limit the functionality of any computer software or hardware or tele
9. the Website is alphanumerically greater than your version download and install the newer version by following the instructions on the Website 4 3 Disable DHCP on the Wired LAN Port To perform the initial configuration disable DHCP on the Ethernet port that connects to the wired LAN Connect to the LAN through either Ethernet port by convention and as used throughout this document Ethernet port 2 is used as the wired LAN port By default DHCP is enabled on Ethernet port 2 Disable DHCP on the port by entering the Ethernet 2 context and issuing the set dhcp disable command WS5000 gt cfg ethernet 2 WS5000 Cfg Ethernet 2 gt set dhcp disable After you disable DHCP information about Ethernet port 2 is listed In this listing DHCP Status should be given as Disable WS5000 Cfg Ethernet 2 gt set dhcp disable Configuring Ethernet port Status Success Ethernet Port information Name Ethernet 2 Network Interface Card 2 Description Ethernet Adapter MAC Address gt OO0810 C6s15 9121F Status Enable Online No Configured Mode auto Negotiated Mode Duplex Half Negotiated Mode Speed 10 DHCP status Disable WS5000 Cfg Ethernet 2 gt 4 4 Set Static IP Information on the Wired LAN Port Within the Ethernet 2 context use the ipaddress command to set the static IP address and subnet mask in that order WS5000 Cfg Ethernet 2 gt ipaddress w x y
10. whatsoever for any use Licensee makes of the Software Licensee shall indemnify and hold harmless Licensor from any claims damages liabilities costs and fees including reasonable attorney fees arising from Licensee s use of the Software as well as from Licensee s failure to comply with any term of this Agreement FAULT TOLERANCE The Software is not fault tolerant and is not designed manufactured or intended for use or resale in on line control equipment in hazardous environments requiring fail safe performance such as but not limited to the operation of nuclear facilities aircraft navigation or communication systems air traffic control life support machines or weapons systems in which the failure of the Software could lead directly or indirectly to death personal injury or physical or environmental damage High Risk Activities Licensor and its suppliers specifically disclaim any express or implied warranty of fitness for High Risk Activities U S GOVERNMENT LICENSE RIGHTS Software provided to the U S Government pursuant to solicitations issued on or after December 1 1995 is provided with the commercial license rights and restrictions described elsewhere herein Software provided to the U S Government pursuant to solicitations issued prior to December 1 1995 is provided with Restricted Rights as provided for in FAR 48 CFR 52 227 14 JUNE 1987 or DFAR 48 CFR 252 227 7013 OCT 1988 as applicable The Manufacturer for pur
11. 5 93 in Weight 6 25 kg 13 75 lbs Max Power Consumption 100 VAC 50 60 Hz 3A 240 VAC 50 60 Hz 1 5A Operating Temperature 10 C 35 C 50 F 95 F Operating Humidity 5 85 without condensation 2 2 Power Cord Specifications A power cord is not supplied with the device Use only a correctly rated power cord that s certified as appropriate for the country of operation 2 2 1 Power Protection e If possible use a circuit that is dedicated to data processing equipment Commercial electrical contractors are familiar with wiring for data processing equipment and can help with the load balancing of these circuits e Install surge protection Be sure to use a surge protection device between the electricity source and the WS5100 e Install an Uninterruptible Power Supply UPS A UPS provides continuous power during a power outage Some UPS devices have integral surge protection UPS equipment requires periodic maintenance to ensure reliability A UPS of the proper capacity for the data processing equipment must be purchased 2 3 Cable Requirements To connect the WS5100 to the LAN and the WLAN you ll need two Category 6 Ethernet cables not supplied one for each of the two Ethernet ports on the front panel of the device 3 4 WS5000 Series WS5100 Installation Guide To connect the WS5100 to a computer that s running a serial terminal emulator program the configuration compu
12. ATSOEVER INCLUDING BUT NOT LIMITED TO DAMAGES FOR LOSS OF PROFITS OR CONFIDENTIAL OR OTHER INFORMATION FOR BUSINESS INTERRUPTION FOR PERSONAL INJURY FOR LOSS OF PRIVACY FOR FAILURE TO MEET ANY DUTY INCLUDING OF GOOD FAITH OR OF REASONABLE CARE FOR NEGLIGENCE AND FOR ANY OTHER PECUNIARY OR OTHER LOSS WHATSOEVER ARISING OUT OF OR IN ANY WAY RELATED TO THE USE OF OR INABILITY TO USE THE SOFTWARE THE PROVISION OF OR FAILURE TO PROVIDE SUPPORT SERVICES OR OTHERWISE UNDER OR IN CONNECTION WITH ANY PROVISION OF THIS AGREEMENT EVEN IN THE EVENT OF THE FAULT TORT INCLUDING NEGLIGENCE STRICT LIABILITY BREACH OF CONTRACT OR BREACH OF WARRANTY OF LICENSOR OR ANY SUPPLIER AND EVEN IF LICENSOR OR ANY SUPPLIER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES LIMITATION OF LIABILITY AND REMEDIES Notwithstanding any damages that Licensee might incur for any reason whatsoever including without limitation all damages referenced above and all direct or general damages the entire liability of Licensor and any of its suppliers under any provision of this Agreement and Licensee s exclusive remedy for all of the foregoing shall be limited to the greater of the amount actually paid by Licensee for the Software or U S 5 00 The foregoing limitations exclusions and disclaimers shall apply to the maximum extent permitted by applicable law even if any remedy fails its essential purpose INDEMNITY Licensee agrees that Licensor shall have no liability
13. Guide this document e Rack mounting brackets 2 e Mounting screws 4 e Console cable e WS5100 product CD 1 2 Document Conventions The following graphical alerts are used in this document to indicate notable situations NOTE Tips hints or special requirements that you should take mY note of CAUTION Care is required Disregarding a caution can result in data loss or equipment malfunction 1 2 WS5000 Series WS5100 Installation Guide personal injury or equipment damage In WARNING Indicates a condition or procedure that could result in 3 Warnings Read all installation instructions and site survey reports and verify correct equipment installation before connecting the system to its power source Remove jewelry and watches before installing this equipment Install the equipment in a rack with adequate dimensions and weight allowances Verify that the rack is anchored and cannot tip over or break away from its mountings Verify that the unit is grounded before connecting it to the power source Verify that any device connected to this unit is properly wired and grounded Connect all power cords to a properly wired and grounded electrical circuit Verify that the electrical circuits have appropriate overload protection Attach only approved power cords to the device Symbol Technologies strongly recommends the use of an Uninterruptible Power Supply UPS that supports the WS5100 power rating No
14. Requirements The WS5000 Series applet is accessed through Internet Explorer version 5 5 using the SUN JRE Java Runtime Environment 1 4 2 04 Later versions of IE and the SUN JRE are also supported A copy of the SUN JRE is provided with your WS5100 product CD To install the JRE insert the CD wait for the Flash menu to appear and then select Install the SUN JRE To prepare Internet Explorer to run the WS5000 Series applet 1 Open IE s Tools gt Internet Options panel and select the Advanced tab 2 Uncheck the following checkboxes Use HTTP 1 1 Java console enabled requires restart e Java logging enabled JIT compiler for virtual enabled requires restart Further Configuration through the Quick 15 Start View 5 2 Launching the Quick Start View To use the Quick Start View launch a Web browser on a computer that can access your WS5100 1 Point the browser to the IP address you assigned to the wired Ethernet port port 2 in Set Static IP Information on the Wired LAN Port on page 12 Specify a secure connection using the https protocol The WS5000 login screen displays WS 5000 Series Wireless Switch Enter user ID and password Login 2 Enter the User ID admin and Password symbol Both are case sensitive 16 WS5000 Series WS5100 Installation Guide 3 Click Login The WS5000 Switch Policy window appears WS 5000 wiris smiten view Create Modify System Settings Run Hel
15. Wireless Switch Soe WS5000 Series WS5100 Installation Guide symbol The Enterprise Mobility Company WS5000 Series WS5100 Installation Guide S a Introduction 0 cece cece eee eee eee 1 Specifications csici2 chsiececeeusastitnevadetatdeeinewasars 3 Hardware Setup 0cce cece cece eee eee eee e eee 6 Preliminary Configuration through the CLI 10 Further Configuration through the Quick Start View 14 Verifying the Configuration ceceeeeeee 22 Shutting Down the WS 5100 cece eee eee 24 Additional CLI Information 0 c cece eee 26 Regulatory Information ccc cece eee eee ee 27 Part Numbers Support and Sales 25055 29 Symbol Technologies Inc End User License Agreement 31 2001 2006 by Symbol Technologies Inc All rights reserved No part of this publication may be modified or adapted in any way for any purposes without permission in writing from Symbol Technologies Inc Symbol The material in this manual is subject to change without notice Symbol reserves the right to make changes to any product to improve reliability function or design No license is granted either expressly or by implication estoppels or otherwise under any Symbol Technologies Inc intellectual property rights An implied license only exists for equipment circuits and subsystems contained in Symbol products
16. ack in the WS5000 Quick Start View click Apply to save the configuration WS 5000 Wireless Switch WS5000 Quick Start View Configure a basic Switch Policy with up to four WLANs one security type per WLAN and other common settings in this view To configure advanced features and options or to view your existing configuration please use the Policy view Switch Settings Country None x Date 200541728 YYYYMMDD Time 12 45 am gt HHEMM Warm Standby Primary 7 Time Zone emrt 08 00 Pacific Time US amp Canada Tijuana ba WLAN 1 WLAN 2 WLAN 3 WLAN 4 ESSID Bandwidth LAN fethernet2 gt Encryption Authentication None hone Keyguard Configure C Pre Shared Key WEP Configure C Kerberos Conficuire CoP ATKIP Conflqure Cs024x EAP Configure I WPRA2ICCMP Gonifiaire Further Configuration through the Quick 21 Start View 12 An information panel appears click OK imormanon Information Wireless Switch Policy has been saved successfully NOTE Your new configuration is not displayed in the Quick Start View To view the policy you just created you J have to go to the View gt Policy window The policy is given a default name that corresponds to WLAN 1 22 WS5000 Series WS5100 Installation Guide 6 Verifying the Configuration The surest way to verify your WLAN configuration is valid and that the switch is fully operational is t
17. ber of the unit this is the same as the MAC of NIC 1 e Model number or product name e Software type and version number 29 30 WS5000 Series WS5100 Installation Guide Customer Support Web Sites Comprehensive on line support is available at the MySymbolCare Web site Registration is free and a variety of services can be linked through this Web portal MySymbolCare for RMA Requests http www symbol com services msc msc html Symbol Services Homepage http www symbol com services Symbol Software Updates http www symbol com services downloads Symbol Developer Program Web Site http devzone symbol com Product Sales and Product Information North America International Symbol Technologies Inc Symbol Technologies Inc One Symbol Plaza Symbol Place Holtsville New York 11742 1300 Winnersh Triangle Berkshire RG41 5TP United Kingdom Tel 1 631 738 2400 or 1 800 722 6234 Tel 0800 328 2424 Inside UK Fax 1 631 738 5990 44 118 945 7529 Outside UK Other Sales Offices For other sales offices visit the Symbol Services Web site http www symbol com services howto howto_contact_us html General Information For general information contact Symbol at Telephone North America 1 800 722 6234 Telephone International 1 631 738 5200 Website http www symbol com product may cause radio interference in which case the CAUTION This is a class A product In a domestic environment this A user
18. communications equipment Licensee not Licensor remains solely responsible for all Content that Licensee uploads posts e mails transmits or otherwise disseminates using or in connection with the Software 4 FEES SUPPORT AND UPGRADES Licensor may at Licensor s sole option provide support services related to the Software Support Services Nothing in this Agreement grants Licensee any right to receive any Support Services Use of any Support Services provided is governed by the Licensor policies and programs described in the user manual in online documentation and or in other Licensor provided materials or support agreements Any supplemental software code provided to you as part of any Support Services shall be considered part of the Software and subject to the terms and conditions of this EULA With respect to technical information you provide to Licensor as part of any Support Services Licensor may use such information for its business purposes including for product support and development Licensor will not utilize such technical information in a form that personally identifies Licensee 5 TERMINATION Either party may terminate this Agreement at any time with or without cause upon written notice Any termination of this Agreement shall also terminate the licenses granted hereunder Upon termination of this Agreement for any reason Licensee shall return all copies of the Software to Licensor or destroy and remove from all comput
19. d Sales All Symbol devices are designed to be compliant with rules and regulations of locations they are sold in A and are labeled as required Any changes or modifications to Symbol Technologies equipment that are not expressly approved by Symbol Technologies are possibly unsafe and could render the equipment inoperable product may cause radio interference in which case the user CAUTION This is a class A product In a domestic environment this may be required to take adequate measures Radio Frequency Interference Requirements USA This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Radio Frequency Interference Requirements Canada This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada Marking and European Economic Area EEA CE
20. er done Shutting down snmpd agent done Shutting down Postgres done INIT Sending processes the TERM signal Hostname WS5000 symbol com Shutting down PacketSwitch interface Shutting down dhcp daemon done Shutting down apache server in the OPEN mode done Cell controller not running i2c core Device or resource busy Shutting down Postgres done Stopping periodic command scheduler cron Stopping internet superserver inetd Saving random seed done Stopping deferred execution scheduler atd Stopping kernel log daemon klogd Stopping system log daemon syslogd flushing ide devices hda System halted Shutting Down the WS5100 As directed wait 10 seconds and turn off the device by toggling the power switch JN WARNING An improper shutdown can render the WS5100 inoperable such that it may require service by Symbol Support Please do not remove AC power or turn off the WS5100 by toggling the on off switch on the back of the device without first following the shutdown procedure outlined above An abrupt loss of power can corrupt the information that s stored on the device 25 26 WS5000 Series WS5100 Installation Guide 8 Additional CLI Information 8 1 CLI Contexts At each step of the configuration you ll be asked to invoke CLI commands within a particular context To enter the main configuration context type configure at the top level CLI prompt
21. ers hard drives networks and other storage media all copies of the Software and shall so certify to Licensor that such actions have occurred Sections 2 13 shall survive termination of this Agreement 6 DISCLAIMER OF WARRANTIES To the maximum extent permitted by applicable law Licensor and its suppliers provide the Software and any if any Support Services AS IS AND WITH ALL FAULTS and hereby disclaim all warranties and conditions either express implied or statutory including but not limited to any if any implied warranties or conditions of merchantability of fitness for a particular purpose of lack of viruses of accuracy or completeness of responses of results and of lack of negligence or lack of workmanlike effort all with regard to the Software and the provision of or failure to provide Support Services ALSO THERE IS NO WARRANTY OR CONDITION OF TITLE QUIET ENJOYMENT QUIET POSSESSION CORRESPONDENCE TO DESCRIPTION OR NON INFRINGEMENT WITH REGARD TO THE SOFTWARE THE ENTIRE RISK AS TO THE QUALITY OF OR ARISING OUT OF USE OR PERFORMANCE OF THE SOFTWARE AND SUPPORT SERVICES IF ANY REMAINS WITH LICENSEE 10 11 12 Symbol Technologies Inc End User License Agreement EXCLUSION OF INCIDENTAL CONSEQUENTIAL AND CERTAIN OTHER DAMAGES TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW IN NO EVENT SHALL LICENSOR OR ITS SUPPLIERS BE LIABLE FOR ANY GENERAL SPECIAL INCIDENTAL DIRECT INDIRECT OR CONSEQUENTIAL DAMAGES WH
22. he WLAN 1 form set Encryption to WEP set Authentication to Pre Shared Key Encryption Authentication C None g C Keyguard Pre Shared Key G WEP Configure 0 Kerberos WPAJTKIP i C 8021xEAP WPA 2 CCMD i Further Configuration through the Quick 19 Start View Click the Configure button next to the WEP radio button The WEP Encryption Key Settings dialogue panel is displayed Security Policy Wizard WEP Encryption Key Settings Where Am Your Policy supports Mobile Units using pre shared manually fixed WEP keys Enter WEP keys values below WEP Key Size 40 bitKey C 128 bit Hex Key Pass Key Symbol Defaut Enter any string to create a set of WEP keys compatible with all Symbol key 1 7asssqnsp6 Ckey 2 232EareF6 C Key 3 aasses143A 0S ree Ckey 4 sseovFelE 40 bit Enter 5 ASCII or 10 hexadecimal characters 128 bit Enter 13 ASCII or 26 lt Back Next gt Finish Cancel Help Java Applet Window 9 Select the Key Size This can be either a 40bit key or 128 bit hex key Once you have A N CAUTION Don t use the values shown in the illustration selected the key size enter the Pass Key The Pass key should have a minimum of 4 characters Click the Generate button to generate the 4 Key feilds 10 After you ve recorded your key values click Save at the bottom of the dialogue 20 W4S5000 Series WS5100 Installation Guide 11 B
23. lug the cord into a standard AC outlet with a voltage range of 100 to 240 VAC 4 Toggle the power switch at the back of the WS5100 to the On position WARNING An improper shutdown can render the WS5100 inoperable A such that it may require service by Symbol Support Please do not remove AC power or turn off the WS5100 by toggling the on off switch on the back of the device without first following the shutdown procedure described in Shutting Down the WS5100 on page 24 An abrupt loss of power can corrupt the information stored on the device 3 4 Verifying the Installation View the LEDs on the front panel of the WS5100 to ensure the device is functioning properly The normal LED pattern follows this path Hardware Setup e During the Power On Self Test POST the two LEDs cycle through all three colors blue amber red e Ifthe POST test fails both LEDs will eventually blink red If the POST test succeeds the LEDs will be momentarily lit solid blue e As the software is initialized the top LED will be solid blue and the bottom LED will be unlit e After the software has finished initializing the top LED will be solid amber and the bottom LED will blink amber The WS5100 is ready to be configured as described in the next chapter Other LED codes indicate the presence or absence of access ports different standby states and so on A guide to the WS5100 LEDs codes is provided in LED Codes on page 4
24. me cli to continue user name cli NOTE If the user name prompt isn t displayed press Enter until it Ri appears Next you ll be taken to the CLI login Log in as admin with the password symbol Preliminary Configuration through the CLI 11 Symbol Wireless Switch WS 5000 Series Please enter your username and password to access the Command Line Interface userid admin KKKKKK password Retrieving user and system information Setting user permissions flags Checking KDC access permissions Welcome Creating the Event list System information System Name Description Switch Location Software Ver Licensed to Copyright rights reserved Serial Number Number of Licenses Max Access Ports Max Mobile Clients MU Idle Timeout value Active Switch Policy Emergency Switch Policy Switch Uptime Global RF stats of Unassigned Access Ports CLI AutoInstall Status WS5000 gt WS5000 WS5000 Wireless Network 2 1 0 0 Oxxx Symbol Technologies Copyright c 2000 2006 All OOA0F8545254 48 48 4096 1800 seconds symbo12006 Not defined 00d 00h 35m Disabled 0 Enabled Compare the value of the Software Ver field to the value on the Symbol Website at http www symbol com services downloads download_switchwireless html 12 WS5000 Series WS5100 Installation Guide If the Website software is newer if the 2 x y z nnnA number on
25. o associate a mobile unit MU and confirm that the MU can communicate with a device on the wired LAN Follow these steps 1 Deploy the WS5100 into the wired and wireless networks by connecting the Ethernet cables as described in Adding the WS5100 to the Network on page 6 Identify by IP address or host name a computer the WS5100 can communicate with over the wired LAN This is the device the MU will try to communicate with later in these instructions Make sure an access port has been adopted by the WS5100 Configure the MU with the same ESSID MyWLAN and WEP encryption settings that you used in the Quick Start View configuration After you ve configured the MU verify that it has been associated by the returning to the Policy View screen and clicking Mobile Units The MU View should have an entry that identifies your mobile unit and shows the RF State as Associated If it doesn t check the ESSID and encryption settings are properly set on the MU MU View MMU Details WLAN All WLANs z P Include MUs which are Away Type MAC Address IP Address WLAN RF State Authentication State gt 00 A0 F8 A7 44 DE 2 2 2 211 QIWLANO1 Associated Authenticated PE gt MU Count 1 Refresh Verifying the Configuration 6 Ifyou want more information select the mobile unit and click Properties The MU Properties dialogue displays everything the switch knows about your mobile unit MU Properties Ea
26. one x Date 20057 1428 YY YY MMIDD Time 14245 JAM v HH MM Warm Standby Primary v Time Zone com 08 00 Pacific Time US amp Canada Tijuana v WLAN 1 WLAN 2 WLAN 3 j WLAN 4 i ESSID Bandwidth LAN Ethernet 2 X Encryption Authentication None Kone F Keyguard Configure C Pre Shared Key O WEP Canfiaure C Kerbero Configure CWPAITKIP Contiaure C s021xEAp Gantigure WPRA2ICCMP Configure undo Apply Help Logout vonnected Om osrwaoT 2 OG 5 In the Switch Settings form set the Country to the country the switch is operating in leave Warm Standby as Primary and set the various date and time parameters Switch Settings Country None 7 Date 200541728 YYYYMMDD Time 1245 fam v HH MM Warm Standby primary v Time Zone GMT 08 00 Pacific Time US amp Canada Tijuana bd code is set Failure to set the proper country could violate CAUTION The switch can t adopt access ports until the country Z regulatory laws 18 WS5000 Series WS5100 Installation Guide 6 Inthe WLAN 1 form in the lower half of the window set the ESSID to a unique value MyWLAN in the example set the Bandwidth to 100 and set the LAN to Ethernet 1 WLAN WLAN 1 WLAN 2 ESSID My WLAN Bandwidth 100 LAN Ethernet 2 v Make a note of the ESSID value you ll need it later when you verify the configuration 7 Inthe lower part of t
27. p ig Default Ethernet Policy i po ow e ethernet Default Access Port Policy E Detector APs i g00 A0 F8 00 00 26 G 00 A0 F8 CD C9 44 t 100 A0 F 8 00 00 26 A D00 A0 F8 CD C9 4A A Mobile Units GBUnavailable Access Ports Unassigned Access Ports jKnown APs e Eo 00 A0 F8 C5 1 E 7F 05 SAIEO ROR NP se 500 A0 F8 CB 0B C4 Switch Policy m Policy Policy Name fault tch F Properties Country India na Adoption List gt Wireless Switch Name wvS5000 Type Standby Description WS5000 Wireless Network Location Status 2 Access Ports Currently Active MU idle timeout Secs 1800 License Software Version 2 1 0 0 011B8 License Level 48 Access Ports 4096 MUs Serial Number OOAOF853E34B Adoption Level 48 Access Parts Help Logout _ p pa Further Configuration through the Quick 17 Start View 4 From the main menu select View gt Quick Start The WS5000 Quick Start View window appears Use this window to create the WLAN policy and apply it to the WS5100 WS 5000 Wireless Switch symbol view Create Modify System Settings Run Help WS5000 Quick Start View Configure a basic Switch Policy with up to four WLANs one security type per WLAN and other common settings in this view To configure advanced features and options or to view your existing configuration please use the Policy view Switch Settings Country N
28. poses of these regulations is Symbol Technologies Inc One Symbol Plaza Holtsville NY 11742 EXPORT RESTRICTIONS Licensee shall comply with all export laws and restrictions and regulations of the Department of Commerce the United States Department of Treasury Office of 33 34 WS5000 Series WS5100 Installation Guide 13 Foreign Assets Control OFAC or other United States or foreign agency or authority and Licensee shall not export or allow the export or re export of the Software in violation of any such restrictions laws or regulations By downloading or using the Software Licensee agrees to the foregoing and represents and warrants that Licensee is not located in under the control of or a national or resident of any restricted country MISCELLANEOUS Licensee may not sublicense assign or transfer this Agreement or its rights or obligations hereunder without the prior written consent of Licensor Any attempt to otherwise sublicense assign or transfer any of the rights duties or obligations hereunder is null and void Licensor may assign this Agreement in its sole discretion In the event that any of the provisions of this Agreement shall be held by a court or other tribunal of competent jurisdiction to be illegal invalid or unenforceable such provisions shall be limited or eliminated to the minimum extent necessary so that this Agreement shall otherwise remain in full force and effect No waiver or modification of this Ag
29. red devices are connected through Switch B To add the WS5100 to the wired and wireless networks and prepare it for initial configuration follow these steps 1 Using a Category 6 Ethernet cable connect a LAN switch Switch A to the Eth1 Ethernet port the left port on the front panel of the WS5100 2 Add your access port s to the WLAN 3 Using a Category 6 Ethernet cable connect another LAN switch Switch B to the Eth2 Ethernet port the right port on the front panel of the WS5100 7 8 WS5000 Series WS5100 Installation Guide 4 Using the supplied console cable connect the WS5100 serial port to an RS 232 DB 9 serial port on a separate computer the configuration computer 5 On the configuration computer configure a terminal emulation application such as HyperTerminal as follows Terminal Type VT 100 Port COM 1 4 depending on which COM port you re using Terminal Settings 19200 bps transfer rate 8 data bits no parity 1 stop bit no flow control no hardware compression The WS5100 does not need to be fully deployed into the wired or wireless network to complete the installation steps outlined in Preliminary Configuration through the CLI on page 10 3 3 Supplying Power to the WS5100 1 Verify that the WS5100 power switch is off before connecting the AC power cord 2 Plug an approved AC power cord into the power connector at the back of the WS5100 3 P
30. reement will be binding upon a party unless made in writing and signed by a duly authorized representative of such party and no failure or delay in enforcing any right will be deemed a waiver This Agreement shall be governed by the laws of the State of New York without regard to the conflicts of law provisions thereof The application the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded Unless waived by Licensor for a particular instance any action or proceeding arising out of this Agreement must be brought exclusively in the state or federal courts of New York and Licensee hereby consents to the jurisdiction of such courts for any such action or proceeding This Agreement supersedes all prior discussions and writings and constitutes the entire agreement between the parties with respect to the subject matter hereof The prevailing party in any action arising out of this Agreement shall be entitled to costs and attorneys fees Symbol Technologies Inc One Symbol Plaza Holtsville New York 11742 1300 http www symbol com 72E 80916 01 Rev A May 2006
31. t using a UPS can result in data loss or equipment damage due to a power surge or power failure Verify that the power connector and socket are accessible at all times during the operation of the equipment Do not work with power circuits in dimly lit spaces Do not install this equipment or work with its power circuits during thunderstorms or other weather conditions that could cause a power surge Verify that there is adequate ventilation around the device and that ambient temperatures meet equipment operation specifications k A Site Preparation Consult your site survey and network analysis reports to determine specific equipment placement port capacity power drops and so on Assign installation responsibility to the appropriate personnel Identify where all installed components are located Verify appropriate rack mounting requirements Provide a sufficient number of power drops for your equipment Ensure adequate dust free ventilation to all installed equipment Identify and prepare Ethernet and console port connections Verify that cable lengths are within the maximum allowable distances for optimal signal transmission Verify that the WS5100 is powered through an Uninterruptible Power Supply UPS 2 Specifications 2 1 Physical Specifications Specifications 48 1 cm 18 93 in with mounting brackets Width 42 9 cm 16 89 in without mounting brackets Height 4 39 cm 1 73 in Depth 40 46 cm 1
32. ter you need the console cable that s supplied with the device You ll use the terminal emulator program to access the switch s Command Line Interface CLI through which you ll perform initial configuration as described in Preliminary Configuration through the CLI on page 10 2 4 LED Codes The WS5100 has two vertically stacked LEDs on its front panel The LEDs display three colors blue amber and red and three lit states solid blinking and off The following tables decode the combinations of LED colors and states 2 4 1 Start Up Event Top LED Bottom LED Power off Off Off Power On Self Test POST running All colors in rotation All colors in rotation POST succeeded Blue solid Blue solid Software initializing Blue solid Off Software initialized Blue blinking Off 2 4 2 Configured as a Primary Switch Event Top LED Bottom LED Active Blue blinking Blue solid Monitoring Blue blinking Amber solid Standby missing or not enabled Blue blinking Off Inactive Amber blinking Blue blinking 2 4 3 Configured as a Standby Switch Event Top LED Bottom LED Active acting as primary Blue blinking Blue blinking Monitoring Blue blinking Amber solid Specifications Event Top LED Bottom LED Standby not enabled Blue blinking Off Inactive Amber blinking Amber blinking 2 4 4 Error Codes
33. tion Licensee may download install and use the Software only on a single computer Licensee may make one copy of the Software excluding any documentation for backup purposes provided that copyright and other restricted rights notices of Licensor and its suppliers are reproduced exactly 2 LICENSE RESTRICTIONS Except as expressly permitted by this Agreement Licensee shall not nor permit anyone else to directly or indirectly i copy except for one backup copy modify distribute or create derivative works based upon the Software ii reverse engineer disassemble decompile or otherwise attempt to discover the source code or structure sequence and organization of the Software or iii rent lease or use the Software for timesharing or service bureau purposes or otherwise use the Software for any commercial purpose on behalf of any third party Licensee shall maintain and not remove or obscure any proprietary notices on the Software and shall reproduce such notices exactly on all permitted copies of the Software All title ownership rights and intellectual property rights in and to the Software and any copies or portions thereof shall remain in Licensor and its suppliers or licensors Licensee understands that Licensor may modify or discontinue offering the Software at any time The Software is protected by the copyright laws of the United States and international copyright treaties The Software is licensed not sold This Agreement does
34. z 255 d e f Preliminary Configuration through the CLI 13 Next set the gateway and DNS server addresses WS5000 Cfg Ethernet 2 gt set gateway a b c d WS5000 Cfg Ethernet 2 gt set dns m n o p After each of these commands information about the context is displayed Check the IP address settings to make sure they re correct At this point the initial configuration of the WS5100 is complete Continue the configuration through the switch s Web based applet interface as described in the next section 14 WS5000 Series WS5100 Installation Guide 5 Further Configuration through the Quick Start View To complete the initial configuration of the WS5100 use the Quick Start View The Quick Start View is part of the WS5000 Series applet a Web based tool that lets you configure your WS5100 switch through an intuitive graphical interface The Quick Start View portion of the applet is designed to take a factory fresh switch and bring it up to a minimal working configuration For advanced switch configuration refer to the WS5000 Series System Reference which you I find on the product CD Using the instructions below create a WLAN policy and a security policy You ll then apply these policies to the WS5100 switch policy After you ve created and applied the policies you should be able to adopt and communicate with properly configured mobile units as described in Verifying the Configuration on page 22 5 1 Applet
Download Pdf Manuals
Related Search