Blade - Fantasia Ceiling Fans
Contents
1. Before commencing installation turn off electricity supply at the main power box Disconnect power by removing fuse or turning off circuit breaker before commencing work Installation directly mounted to Ceiling Joist Ceiling Joist behind ceiling approx 75mm 3 Check that the mounting location is of adequate strength to Ensure the Supply Wiring is of support the fan sufficient length Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 7 Attaching Hanger Bracket directly to Ceiling Drill holes in Ceiling Joist at approximately 90mm 3 2 centres for Hanger Bracket mounting Secure Hanger Bracket to Ceiling Joist using screws and washers provided Ensure screws are securely tightened Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com Terminal Block SWITCHED LIVE from Wall Controller Ensure that electrical connections are good and that terminal block screws are secure Make NEUTRAL Blue or Black and EARTH Green amp Yellow connections from incoming Mains supply to NEUTRAL and EARTH terminals on Hanger Bracket as appropriate Make SWITCHED LIVE Brown or Red connection from Wall Switch to LIVE terminal on Hanger Bracket This wire could also be Blue or Black with a Brown or Red marking2. Repair of a ceiling fan used incorrectly accidentally damaged modified in any way or not serviced in accordance with the maintenance instructions Travelling costs incurred by Fantasia Distribution Ltd s personnel or service agents over 25km from a Fantasia Distribution Ltd authorised service depot and or the cost of transporting and insuring the ceiling fan between the nearest Fantasia Distribution Ltd agents service depot and its normal location These costs must be met by the purchaser Subject to any statutory provisions to the contrary claims for damage to furniture carpet walls ceilings foundations or any other consequential loss either directly or indirectly resulting from a faulty ceiling fan Blade Ceiling Fans not purchased and installed in Mainland UK A service call fee will be charged where there is nothing wrong with the ceiling fan or the defective operation of the ceiling fan is due to failure of electricity or the installation is not in accordance with Fantasia Distribution Ltd instructions and or applicable local regulations or the defects have been caused by incorrect application or abuse of the ceiling fan or the damage has been caused by unauthorised persons attempting to repair the fan Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1D
3. Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 29 Trouble Shooting WARNING Except for items 1 and 2 below the following require access to areas of the fan which carry lethal voltage There are no other checks which can be carried out by the user Apart from items 1 and 2 the following must be carried out by properly qualified person If the fan does not operate properly or turns on or off at random 1 If applicable change the battery in the Remote Control Transmitter Handset 2 Check to ensure the Remote Control Code switches on the Remote Control Receiver and Transmitter Handset are set to same positions Sometimes the Handset Code switches may be bumped when the battery is changed see section 12 3 Check the main and branch circuit breakers and or fuses 4 Check the wire connections to the fan If the fan is noisy 1 Check to make sure that the screws securing the Suspension Ball Fan Motor Housing and Fan Blade are tightened securely but are not over tight see sections 9 21 amp 24 2 Check that all the screws in the Hanging Bracket are tight If the fan rotates but does not create much airflow 1 The room may contain items which obstruct the air flow 2 The fan may be too small for the size of the room Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info
4. Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 4 Unpacking your Blade Fan Unpack your fan and check the contents You should have two cartons a Motor Carton and a Blade Carton Do not discard the cartons If warranty replacement or repair is ever necessary the fan should be returned in the original packaging Examine all parts You should have the following Hanger Bracket Hardware Screw C ZOTE Manger Bracket xX 1 unit screw x 2 units Fan Motor Assembly Washer x 1 unit x 2 units x 2 units ee Fan Motor Housing E ane Aau P Sts 1 1 spare in Fan Blade a aa ne ee ee x 1 unit Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 5 Unpacking your Blade Fan Remote Control Receiver x unit Remote Control Transmitter x l unit Battery x1 unit Note Remote Control Transmitter may vary from one shown Warning Do not attempt to control the operation of this fan from any control system that is not approved by Fantasia Distribution Ltd for use with this fan Do not use a solid state wall controller The use of an unapproved control system voids the warranty Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 6 Checking Ceiling Condition and Preparing for Fan Installation
5. 49 Section 50 51 Section 52 Section 55 Unpacking Your Blade Fan Suspension Kit Preparing Fan Motor Assembly Preparing Suspension Rod Attaching Suspension Rod to Suspension Cover Attaching Suspension Rod to Fan Motor Assembly Making Fan Motor Assembly Electrical Connections Attaching Canopy and Suspension Ball to Suspension Rod Installing Fan Motor Suspension Rod Assembly Installing Accessory Remote Control Receiver Making Remote Control Receiver Electrical Connection Installing Canopy Preparing and Installing Fan Motor Housing Product Disposal Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 1 Introduction Thank you for choosing a Blade Ceiling Fan You have chosen the best We are confident that your new ceiling fan will provide many years of service and enjoyment GENERAL PRECAUTIONS Please read and follow these instructions carefully and be mindful of all warnings shown throughout this manual Be cautious Read all instructions and safety information and review the accompanying assembly diagrams before installing your new fan Electricity can kill Please ensure household supplies are fully disconnected before installing or carrying out maintenance on this product Close supervision is necessary when the product is used by children Do not allow children to use it as a toy Fantasia Distribution Ltd Unit B
6. Control Receiver into Hanger Bracket in orientation shown Code switches to be aE passed through Hanger Bracket Fix Remote Control Receiver aerial to ceiling within circle of canopy Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 47 Connecting Live and Neutral Wires from Receiver to Suspension Rod Wires Cote y Make LIVE and NEUTRAL connections from Wires passing through Suspension Rod to Remote Control Receiver wires marked L Brown and N Blue respectively using suitable insulated connectors not supplied Ensure that electrical connections are good and connector screws are secure Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 48 Connecting Earth Wire to Terminal Block on Hanger Bracket Remote Control Make EARTH connection from wire passing through Suspension Rod to appropriate terminal on Hanger Bracket as shown Ensure that electrical connections are good and terminal block screws are secure Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 49 Connecting Live and Neutral Wires to Terminal Block on Hanger Bracket Remote Control Make LIVE Brown and NEUTRAL Blue connections
7. MUST come via a Wall Switch This allows the fan to be manually switched off should a fault ever develop Hanger Control Blocks Bracket Receiver Earth ol i amp E Green Yellow T T 5 i al amp 5 2j I zj 2 g of o w Fe e Chassis oO oO Oo Terminai i Block LO T Chassis E Green Yellow 5 Earth Purple Capacitor Fan Motor Blue Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com Ariel Black 20 Preparing Fan Motor Housing Fan Motor Housing Fan Motor Housing Screw Cover Ensure Fan Motor Housing Screw Covers are in fully open position Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 21 Attaching Fan Motor Housing to Fan Motor Assembly Ensure that Fan Motor Housing fixing point with hole not bayonet slot is aligned with Chassis arm from which fixing screw was removed see page Install Fan Motor Housing using a clockwise bayonet action Line up fixing hole in Fan Motor Housing with screw hole in Chassis arm and install fixing screw removed on page Secure Fan Motor Housing ensuring all three screws are tight but not over tight Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN1
8. a slowly turning fan may help to reduce heating costs Warm air rises to the ceiling where it cannot be felt by the occupants of a room especially in areas with high ceilings The fan helps to keep warm air away from the ceiling and mixes it with the air below Keep the fan speed low so that the effects of evaporative cooling are minimized Normal Wear and Tear 1 Threaded components working slightly loose or parts even slightly damaged or bent during vigorous cleaning or bumping can cause extra wobble and noise This is not covered under warranty but care during maintenance and cleaning should prevent this from occurring Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 31 Technical Specifications Suspended Version Accessory 170 mm gt 365 mm 1060 ram Standard suspension kit suitable for sloped ceilings up to 20 Operating Speeds Approximate figures at 230 240v AC Colour Motor Housing White Brushed Aluminium Low 80 rpm Blade White Brushed Silver Medium 120 rpm High 160 rpm Remote Control Accessory Rated Power Consumption 35W Hand Held RF Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 32 Warranty Ceiling Fan Warranty You must have the original purchase receipt or
9. covered by a 1 year in home warranty under the same conditions as described above for fans The additional 1 year repair or replacement warranty option is offered for Remote Control Transmitters or Receivers Balance of Warranty on Repaired or Replaced Products Any replaced or repaired product is covered only by the balance of the warranty remaining on the original article Transfer of Warranty If the dwelling where the fan or remote control is installed changes hands the balance of the warranty passes to the new owner providing the original bill of sale for the product is retained by the new owner Warranty for the fan does not cover damage to the fan if it is moved from one dwelling to another during the warranty period The warranty is voided in total if the product is sold as second hand goods Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 33 Warranty The following is NOT covered by warranty L Any damage incurred after delivery to the owner that is not caused by a fault in the products materials or workmanship damage from lightning or power surges incorrect installation damage due to incorrect installation water damage of any kind installation or use outdoors damage arising from connection to or use with alternative power systems e g inverters solar etc Ceiling fans not installed by a licensed electrician
10. fantasiaceilingfans com 30 General information on Ceiling Fans General Information L All electrical motors including fan motors make some noise and may feel hot to the touch This is NOT a fault Ceiling fans tend to move during operation due to the fact that they are not rigidly mounted Rigid mountings can generate excessive vibration and stress on the mountings Movement of a couple of centimetres is quite OK and does not suggest that the fan will fall down The Blade fan is mounted securely on a metal Hanger Bracket with rubber cushioning and a ball joint to allow free movement Please note that due to manufacturing variations not all Blade ceiling fans are exactly the same some may move more that others Note Excessive wobble can be caused by the Drive Shaft not being positioned vertically This can be easily rectified by adjusting the position of the Fan Motor Assembly in the Hanger Bracket see section 10 Ceiling fans are an environmentally smart choice to help cool you in your home They work by creating air flow which causes a cooling sensation on the skin The faster the speed of the air flow the greater the cooling sensation Ceiling fans do not work by cooling the room so they should be switched off when there is no one in the room to save energy The effectiveness of ceiling fans is also dependent on the humidity in the air they are more effective in humid environments and less so in dry ones During winter
11. from Remote Control Receiver to Hanger Bracket terminals using wires marked LIVE IN Brown and NEUTRAL IN Blue Ensure that electrical connections are good and terminal block screws are secure Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 50 Slide Canopy up Suspension Rod fit to Hanger Bracket using clockwise bayonet action and tighten fixing screws securely Adjust Canopy fixing screws on Hanger Bracket as shown A Remove protective rubber gasket Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 51 Attaching Canopy Screw Cover to Canopy Fit Canopy Screw Cover to Canopy using a bayonet action as shown Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 52 Preparing Fan Motor Housing Fan Motor Housing _ Fan Motor Housing Screw Cover Ta ee Ensure Fan Motor Housing Screw Covers are in fully open position Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 53 Attaching Motor Housing to Fan Motor Assembly Ensure that Fan Motor Housing fixing point with hole not bayonet slot is aligned
12. with Chassis arm from which fixing screw was removed see page 6 Install Fan Motor Housing using a clockwise bayonet action Line up fixing hole in Fan Motor Housing with screw hole in Chassis arm and install fixing screw removed on page 6 Secure Fan Motor Housing ensuring all three screws are tight but not over tight oI in a G D a Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 54 Closing Screw Covers Note To remove Fan Motor Housing open Screw Covers using a flat bladed screw driver as shown Remove fixing screw from hole loosen two bayonet slot screws and remove Fan Motor Housing by rotating anticlockwise and lowering A Fan Blade must be removed before Fan Motor Housing is removed Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 55 Product Disposal Instructions This product has been classed as Electrical or Electronic Equipment and should not be disposed of with other household or commercial waste at the end of it s working life The Waste of Electrical and Electronic Equipment WEEE Directive 2002 96 EC has been put in place to recycle products using best available practise and minimise the impact upon the environment Fantasia Distribution Ltd Unit B The Flyers Way Westerh
13. 59 564829 Email info fantasiaceilingfans com 25 Closing Screw Cover on Pivot Connector Rotate Screw Cover to hide screw head Note Rotating the Screw Cover will prevent blade fixing screw from falling out should it become loose Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 26 Installation Check Ceiling o WH Rotate Fan Blade by hand to ensure it does not hit anything Make sure that the Drive Shaft is vertical and that the gap between the Fan Motor Housing and ceiling is even If the Drive Shaft is not vertical the fan may wobble Once the installation is completed and has been checked the electricity supply can be turned on at the main power box Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 27 Operating your Blade Fan Remote Control To operate your fan using a Remote Control Handset press the HI MED or LO button to select the desired speed To turn the fan off press the STOP button To change between speeds press the button for the new speed There is no need to stop the fan when changing speed The LIGHT button has no function on the Blade fan Note Remote Control Transmitter may vary from one shown Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN1
14. 6 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 22 Closing Screw Covers Close all three Screw Covers Note To remove Fan Motor Housing open Screw Covers using a flat bladed screw driver as shown Remove fixing screw from hole loosen two bayonet slot screws and remove Fan Motor Housing by rotating anticlockwise and lowering A Fan Blade must be removed before Fan Motor Housing is removed Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 23 Preparing Fan Blade for Installation Pivot Connector Rotate Fan Blade Screw Cover to expose fixing hole in Pivot Connector as shown Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 24 Attaching Fan Blade to Fan Motor Assembly Drive Shaft i o gt t Pivot Connector N rel Align flats on Pivot Connector with flats on Drive Shaft and install Fan Blade by sliding Pivot Connector onto Drive Shaft Hold Fan Blade in position insert blade fixing screw and tighten securely T Take care not to lift Drive Shaft when installing Fan Blade as this may disengage Suspension Ball from lug on Hanger Bracket see section 10 Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 019
15. 6 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 28 Fantasia Distribution Ltd Care and Cleaning Regular cleaning of your Sycamore Ceiling Fan Blade and Fan Motor Housing is the only maintenance that is needed Due to the balanced single blade design a large build up of dust on the blade may eventually create an imbalance causing the blade to wobble during use This is likely to be more apparent on fans with a suspended installation Regular cleaning of the blade is recommended to prevent dust from building up l When cleaning your fan only use a soft brush or lint free cloth to avoid scratching the finish DO NOT use water when cleaning your ceiling fan It could damage the motor or the blade and or create the possibility of electric shock 2 When dusting the Fan Blade you must support the blade to prevent bending no pressure should be applied to the blade pivot After cleaning the Fan Blade check to ensure that the Drive Shaft is vertical otherwise the fan may wobble 3 Occasionally it may be necessary to re tighten the Fan Blade and Fan Motor Housing fixing screws to prevent any clicking or humming sounds during operation This is especially true in climates with broad temperature and humidity ranges and for fans with high gloss painted blades or motor housings 4 If you experience any flaws in the operation of your fan please check the points in the Trouble Shooting section see section29
16. E Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 34 Unpacking your Blade Fan Suspension Kit Unpack your Suspension Kit and check the contents You should have the following items Do not discard the carton If warranty replacement or repair is ever necessary the fan should be returned in the original packaging Examine all parts You should have the following Suspension Hardware aa Ss J Canopy x l unit __ s ETT Screw Shoulder type x a Pise Se EEA 2 units a od ee Canopy Screw Cover x 1 unit ae i 2 a pa a ie z n C Suspension Cover OSS a x 1 unit EO Packaged separately C Suspension i Rod x unit Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 35 Preparing Fan Motor Assembly for Suspended Installation Remove Suspension Ball from Fan Motor Assembly A Put Suspension Pin and Suspension Ball aside for later use Loosen Suspension Ball security screw slide Suspension Ball down shaft and remove Suspension Pin Remove Suspension Ball from shaft Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 36 Preparing Fan Motor Assembly Fan Housing _ Fixing Screw lt Remove one Fan Motor Housing fixing screw and put it aside for re assembly during Fan Motor
17. Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com Suspension Ball Check that the Suspension Ball fixing screw is securely tightened Fan Motor Housing Fixing Screw gt lt 6 8mm 1 4 5 8 Remove one Fan Motor Housing fixing Adjust remaining two Fan Motor Housing screw and put it aside for re assembly fixing screws to provide clearance for during Fan Motor Housing installation installing Fan Motor Housing Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 10 Installing Fan Motor Assembly into Hanger Bracket Position Fan Motor Assembly so that Chassis arm with terminal block is facing away from opening in Hanger Bracket Locate Suspension Ball in Hanger Bracket Ensure that lug on Hanger Bracket is engaged in slot in Suspension Ball TTT TELE Take care to keep Fan Motor Assembly level during installation to avoid marking ceiling Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 11 Connecting Earth Wire from Fan Motor Assembly to Hanger Bracket Make EARTH Green Yellow connection from Fan Motor Assembly to appropriate terminal on Hanger Bracket Ensure electrical connections a
18. Housing installation 6 8mm 1 4 5 8 Fan Motor Housing fixing screw Adjust remaining two Fan Motor Housing fixing screws to provide clearance for installing Fan Motor Housing Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 37 Preparing Suspension Rod Suspension Rod j Live Neutral and Earth Wires Thread Live Neutral and Earth Wires through Suspension Rod as shown 175mm 7 100mm o Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 38 Attaching Suspension Rod to Suspension Cover bore of Suspension Cover Ensure two upper security p E ie screws do not protrude into a Insert Live Neutral and Earth Wires into bore of Suspension Cover and pass through side hole as shown Insert Suspension Rod into Suspension Cover align holes in Suspension Rod and Suspension Cover insert upper shoulder screw o and tighten Tighten two upper security screws Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com Attaching Suspension Cover to Fan Motor Assembly Ensure two lower security screws do not protrude into bore of suspension cover Insert Fan Motor Assembly
19. Owners Installation Manual Please ensure that this manual is retained and held at the installation site Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com Table of Contents Section 1 Section 2 3 Introduction Important Safety Precautions Instructions for Flush Mount Installation Section 4 5 Section 6 Section 7 Section 8 Section 9 Section 10 Section 11 Section 12 14 Section 15 Section 16 18 Section 19 Section 20 22 Section 23 25 Section 26 Section 27 Section 28 Section 29 Section 30 Section 31 Section 32 33 Unpacking Your Blade Fan Preparing Ceiling Installing Hanger Bracket Making Hanger Bracket Electrical Connections Preparing Fan Motor Assembly Installing Fan Motor Assembly Making Fan Motor Assembly Electrical Connections Setting Accessory Remote Control Codes Installing Accessory Remote Control Receiver Making Remote Control Receiver Electrical Connections Accessory Remote Control Installation Diagram Preparing and Installing Fan Motor Housing Preparing and Installing Fan Blade Installation Check Operating Your Blade Fan Care and Cleaning Trouble Shooting General Information on Ceiling Fans Technical Specifications Warranty Instructions for Suspended Installation Section 34 Section 35 36 Section 37 Section 38 Section 39 Section 40 42 Section 43 44 Section 45 Section 46 Section 47
20. The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 2 Important Safety Precautions LOCATION AND INSTALLATION REQUIREMENTS FOR YOUR FAN To provide adequate clearance from the floor the lowest point on the fan blade must be at least 2 3 m 7 6 from the floor Note For a fan mounted directly to the ceiling the lowest point of the fan blade is approximately 365mm 4 4 below the ceiling Note For a fan mounted on a suspension kit the lowest point of the fan blade 1s approximately 375mm 4 plus the nominal length of the suspension rod below the ceiling Make sure that the chosen location of the fan will not allow the rotating fan blade to come into contact with any object Ensure ceiling joists are sound and of adequate size and strength to support a 86Kg 190Ib load To reduce the risk of fire electrical shock or personal injury ensure that the fan mounting bracket is supported directly from the building structure DO NOT mount to an outlet box The mounting bracket must be firmly screwed to a load bearing structure e g a concrete ceiling steel structure or timber frame If a timber frame is to be added it must be securely nailed or screwed between two beams MECHANICAL ISSUES Do not remove the fan from the ceiling after installation Do not attach the Fan Blade before the Fan Motor Housing is installed and secured To protect the finish the Fan Blade and
21. am Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com
22. bill of sale to make a warranty claim No claim will be accepted unless proof of date of purchase is available at the time of making the warranty claim Ceiling Fan Warranty Period The ceiling fan itself excluding accessories such as the Remote Control Transmitter and Receiver is covered by a 1 year in home warranty During this period Fantasia Distribution Ltd will at its discretion repair or replace defective product Labour and product delivery costs are borne by Fantasia Distribution Ltd during this 1 year period Fantasia Distribution Ltd must authorize repairs and the costs associated No costs will be refunded unless Fantasia Distribution Ltd have agreed to them in advance of any work taking place The cost of obtaining or using special access equipment scissor lifts scaffolding etc is specifically excluded and it is the responsibility of the owner to provide such equipment and have it safely installed and operated Following the 1 year in home warranty period Fantasia Distribution Ltd offers a repair or replacement warranty on the motor assembly only for an additional 14 years During this 14 years the owner is responsible for labour costs incurred in removing and re installing the fan and for transport costs to Fantasia Distribution Ltd s repair centre Return freight will be paid by Fantasia Distribution Ltd Remote Control Warranty Period Fantasia Distribution Ltd s Remote Control Receivers and Transmitters Handsets are
23. eiver Codes if using individual Remote Control Handsets for each fan Note Ensure that the maximum distance from the Remote Control Handset to Receiver does not exceed the range of the transmitter Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 15 Tilt Fan Motor Assembly as shown and slide Remote Control Receiver into Hanger Bracket in orientation shown Code switches to be passed through Hanger Bracket After installing Remote Control Receiver readjust Fan Motor Assembly to ensure Drive Shaft is vertical Fantasia Distribution Ltd Fix Remote Control Receiver Aerial to ceiling within circle of Fan Motor Housing Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 16 Removing pre installed Live and Neutral Wires from Fan Motor Assembly ji Pan nai D UC S0h ar eaa fin Ea ER 7 EVE EN pe e n EY ap ve 4 gt Remove pre installed LIVE Brown and NEUTRAL Blue wires from right side of terminal block on Fan Motor Assembly Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 17 Connecting Live and Neutral Wires from Remote Receiver to Bracket Wee SOTO Make LIVE and NEUTRAL connections from Remote Control Rece
24. inal block as shown f AN TSV OGOF Ensure that electrical connections are good and terminal block screws are secure Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 43 Assembling Canopy Screw Cover and Canopy to Suspension Rod rm i r Pa Slide Canopy Screw Cover and Canopy _ A onto Suspension Rod as shown Canopy Canopy Screw Cover Check Canopy Screw Cover is in correct orientation as shown Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com Fantasia Distribution Ltd Locate Suspension Ball and Suspension Pin removed from Fan Motor Assembly on page 5 Slide Suspension Ball onto Suspension Rod insert Suspension Pin locate Suspension Ball onto Suspension Pin and tighten security screw securely Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 45 A Ensure that lug on Hanger Bracket is engaged in slot on Suspension Ball Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 46 Installing Remote Control Receiver META e MIE a WIP ey NIC Cape rm A Y inn 1 Insert Remote
25. iver to appropriate terminals on Hanger Bracket using wires marked LIVE IN Brown and NEUTRAL IN Blue d i D Ensure that electrical connections are good and terminal block screws are secure Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 18 Connecting Live and Neutral Wires from Remote Receiver to Motor Assembly a we A Z LASA Ls e t w N WA ay i j i i o ean m A N e 3 ie P z Make LIVE and NEUTRAL connections from Remote Control Receiver to appropriate terminals on Fan Motor Chassis using wires marked L Brown and N Blue Ensure Remote Control Receiver LIGHT Wire is well secured and cannot touch any moving parts Ensure that electrical connections are good and terminal block screws are secure Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 19 Remote Control Accessory Installation Wiring Diagram NEUTRAL from Mains Sullp 00 AC IN N Blue a SWITCHED LIVE Active from Walt Switch 00 AC IN L Brown Hanger Bracket Remote Terminal r EARTH Conductor Note As shown the Remote Control Receiver is wired in series between the Hanger Bracket terminal and the Chassis terminal A The SWITCHED LIVE wire
26. re good and that terminal block screws are secure Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 12 Setting Code Switches for Remote Control Handset and Installing Battery Check Remote Control Transmitter Handset CODE switch settings are identical to Receiver CODE switch settings use point of ball point pen to adjust switches Remote Control Handset 9v Battery install Battery as shown Battery Compartment Door N ote Remote Control Transmitter may vary from one shown Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 13 Setting Code Switches for Remote Control Receiver Terminate Remote Control Receiver light wire marked LIGHT OUT using good quality electrical insulation tape as shown Light wire Check Remote Control Receiver CODE switch settings and adjust if required use point of ball point pen to adjust switches Remote Control Receiver Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 14 Code Settings for Remote Control Handset and Receiver Setting Handset and Receiver Codes if using one Remote Contro Handset to contro multiple fans Setting Handset and Rec
27. shaft into Suspension Cover bore and align holes in Suspension Cover and Fan Motor Assembly shaft Note Suspension Rod should be attached saa 2 oe pa ee eS ss Insert and tighten lower shoulder screw Tighten two lower security screws Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 40 Removing pre installed Live and Neutral Wires from Fan Motor Assembly SOE es Aom n KOB Remove pre installed LIVE Brown and NEUTRAL Blue wires from right side of terminal block on Fan Motor Assembly Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 41 Connecting Live Neutral and Earth Wires to Terminal Block on Fan Motor Assembly Make LIVE NEUTRAL and EARTH connections from Suspension Rod Wires to appropriate terminals on Fan Motor Assembly terminal block as shown Ensure that electrical connections are good and terminal block screws are secure Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 42 Connecting Earth Wire to Terminal Block on Fan Motor Assembly Make EARTH Green Y ellow connection from Chassis to appropriate terminal on Fan Motor Assembly term
28. the Fan Motor Housing should be kept in their cartons until ready to be installed After the fan is completely installed check to make sure that all connections are secure to prevent the fan from falling and or causing damage or injury To reduce the risk of personal injury do not bend or damage the Motor Drive Shaft or Fan Blade when handling or installing them Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE Tel 01959 564440 Fax 01959 564829 Email info fantasiaceilingfans com 3 Important Safety Precautions ELECTRICAL ISSUES The fan and hanger bracket must be earthed Do not attempt to control the operation of this fan from any wall controller that is not approved by Fantasia Distribution Ltd for use with this fan DO NOT use a solid state wall controller The use of an unapproved control system voids the warranty To avoid possible electric shock during installation be sure the electricity 1s turned off at the main fuse box before commencing work Disconnect power by removing fuse or turning off circuit breaker before installing the fan Ensure all spliced connections are adequately insulated NOTE Nothing in this manual is intended to instruct or assist untrained or unqualified persons to install this product Additionally it is the responsibility of the installer and user to apply common sense and care at all times Fantasia Distribution Ltd Unit B The Flyers Way Westerham Kent TN16 1DE
Download Pdf Manuals
Related Search