Netra ft 1800 Compliance and Safety Manual
Contents
1. In some circumstances if your CD ROM disk does not have a clean data surface your system may fail to boot 12 Safety Precautions The following general safety precautions must be observed during all phases of operation service and repair of this equipment Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design manufacture and intended use of the equipment Sun Microsystems assumes no liability for the customer s failure to comply with these requirements The safety precautions listed below represent warnings of certain dangers of which Sun Microsystems is aware You as the user of the product should note these warnings and all other safety precautions necessary for the safe operation of the equipment in your operating environment Safety Requirements For protection observe the following safety precautions when setting up the equipment z Follow all cautions warnings and instructions marked on the equipment m Ensure that the voltages and frequency rating of the power receptacle match the electrical rating label on the equipment m Never push objects of any kind through openings in the equipment They may touch dangerous voltage points or shor components resulting in fire or electric shock m Refer servicing of equipment to qualified personnel Netra ft 1800 Compliance and Safety Manual February 1999 gt P Ground the Instrument Class 12. Canadian Interference Causing Equipment Regulations Netra ft 1800 Compliance and Safety Manual February 1999 part II Safety Safety gt E Symbols Note A note provides information which should be considered by the reader Caution Cautions identified by this Attention icon carry information about procedures or events which if not considered may cause damage to the data or hardware of your system Caution Cautions identified by this Hazard icon carry information about procedures which must be followed to reduce the risk of electric shock and danger to personal health Follow all instructions carefully Handling and Taking Care of Your CD ROM Disks Please observe the following precautions when handling CD ROM disks z DO NOT touch the data side of the disk the side of the disk with no label z DO NOT apply paper labels or write on any part of the disk data side or label side m If dust or fingerprints get on to the disk wipe with a dry cloth from the center of the disk to the edge 11 z DO NOT place the disk in any place where it will be subjected to direct sunlight or high temperature Caution Do not use Benzene Paint Thinner Record Cleaner Static Repellent or any type of CD Lens cleaner These chemicals can damage the surface of the CD ROM disk In addition these fluids will build up on the lens cleaning brush in your CD ROM reader reducing effectiveness Note
3. eguipment To minimize shock hazard the eguipment enclosure must be reliably connected to an electrical ground This DC unit is provided with an eguipment grounding connection point The eguipment grounding conductor must be securely fastened to the identified ground point Do Not Operate in an Explosive Atmosphere Do not operate the eguipment in the presence of flammable gases or fumes Operation of any electrical eguipment in such an environment constitutes a definite safety hazard Keep Away From Live Circuits Only trained personnel may remove eguipment covers for internal subassembly or component replacement or any internal adjustment Under certain conditions dangerous voltages may exist even with the power supply removed Lithium Cells Caution Each CPUset contains two NVRAM chips containing lithium cells In the unlikely event that one of these requires replacement the chip must be disposed of safely in accordance with the manufacturer s instructions Do Not Service or Adjust Alone Do not attempt internal service or adjustment unless another person capable of rendering first aid and resuscitation is present Safety 13 h Do Not Substitute Parts or Modify Equipment Because of the danger of introducing additional hazards and or the possibility of compromising emissions compliance do not install substitute parts or perform any unauthorized modification of the equipment Contact your local support organization f
4. Netra ft 1800 Compliance and Safety Manual Ss amp SUN microsystems THE NETWORK IS THE COMPUTER Sun Microsystems Inc 901 San Antonio Road Palo Alto CA 94303 4900 USA 650 960 1300 Fax 650 969 9131 Part No 805 7019 10 Revision A February 1999 Copyright 1999 Sun Microsystems Inc 901 San Antonio Road Palo Alto CA 94303 USA All rights reserved This product or document is protected by copyright and distributed under licenses restricting its use copying distribution and decompilation No part of this product or document may be reproduced in any form by any means without prior written authorization of Sun and its licensors if any Third party software including font technology is copyrighted and licensed from Sun suppliers Parts of the product may be derived from Berkeley BSD systems licensed from the University of California UNIX is a registered trademark in the U S and other countries exclusively licensed through X Open Company Ltd Sun Sun Microsystems the Sun logo AnswerBook Java the Java Coffee Cup Netra and Solaris are trademarks registered trademarks or service marks of Sun Microsystems Inc in the U S and other countries All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International Inc in the U S and other countries Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems Inc Registered Excellence
5. an Union Notice 5 Fran ais Garantie de Conformit Les composants et accessoires suivants sont requis 1 Des c bles blind s quip s de fiches en m tal doivent tre utilis s pour toutes les connexions aux raccordements d entr e de sortie de l appareil 2 Le syst me doit tre mis la terre conform ment aux prescriptions Deutsch Sicherstellen der Konformit t Die folgenden Zubeh rteile und zus tzlichen Komponenten werden ben tigt 1 F r alle Verbindungen zu den Anschl ssen des Ger tes sollen abgeschirmte Kabel verwendet werden die mit Metallsteckern ausger stet sind 2 Das System mu stets vorschriftsm ig geerdet sein 6 Netra ft 1800 Compliance and Safety Manual February 1999 Canada Renseignements de compatibilit lectromagnetique Canada Communications Canada c est dire le DOC Minist re des Communications r glemente les dispositifs num rigues de facon analogue aux presciptions de la FCC Commission f d rale des communications aux Etats Unis Chaque produit doit tre tiguet ou livr avec une documentation sp cifiant sa classe Le DOC d finit comme le fait la FCC l environnement dans lequel un dispositif num rique doit tre utilis La classe A sp cifi e par le DOC s applique aux zones industrielles ou commerciales alors que la classe B s appligue aux zones r sidentielles industrielles ou commerciales Comme il en est le cas avec la FCC
6. and Design is a certification mark of Bellcore The OPEN LOOK and Sun Graphical User Interface was developed by Sun Microsystems Inc for its users and licensees Sun acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry Sun holds a non exclusive license from Xerox to the Xerox Graphical User Interface which license also covers Sun s licensees who implement OPEN LOOK GUIs and otherwise comply with Sun s written license agreements RESTRICTED RIGHTS Use duplication or disclosure by the U S Government is subject to restrictions of FAR 52 227 14 g 2 6 87 and FAR 52 227 19 6 87 or DFAR 252 227 7015 b 6 95 and DFAR 227 7202 3 a DOCUMENTATION IS PROVIDED AS IS AND ALL EXPRESS OR IMPLIED CONDITIONS REPRESENTATIONS AND WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT ARE DISCLAIMED EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID Copyright 1999 Sun Microsystems Inc 901 San Antonio Road Palo Alto CA 94303 Etats Unis Tous droits r serv s Ce produit ou document est prot g par un copyright et distribu avec des licences gui en restreignent l utilisation la copie la distribution et la d compilation Aucune partie de ce produit ou document ne peut tre reproduite sous aucune forme par quelque moyen que ce soit sans au
7. bel the product to inform an end user of the maximum emission level from the product when used in accordance with its instructions The FCC has established two classes of levels Class A and Class B A system that meets the FCC Class A requirements may be marketed for use in an industrial or a commercial area A system that meets the more stringent FCC Class B requirements may be marketed for use in a residential area in addition to use in an industrial or a commercial area An end user in the United States is responsible for ensuring that his system is suitable for its environment as stated in the above paragraph and bears the financial responsibility for correcting harmful interference For a system to be considered an FCC Class B system all peripherals of the system workstation monitor keyboard mouse external disk and tape drives modem printer etc must be labeled as such If any peripheral or the system itself is labeled as FCC Class A the entire system becomes FCC Class A and should not be used in a residential area To determine if your system is FCC Class A or FCC Class B you must check the marking on each peripheral and on your workstation Each piece of equipment should have an FCC statement marked on the unit The FCC statement should identify the equipment as Class A or Class B If there is no indication of the Class in the FCC statement consider it to be Class A unless there is a mark which states FCC ID followed by al
8. chaque p riph rique d un syst me doit r pondre aux sp cifications de la classe B d finie par le DOC afin qu un syst me puisse tre consid r comme faisant partie de cette classe Si un p riph rique ou un poste de travail quelconque appartient la classe A le syst me appartient alors la classe A d finie par le DOC et par cons quent ne doit pas tre mis en service dans une zone r sidentielle Au Canada il revient l utilisateur de s assurer que son syst me est appropri pour l environnement auquel il appartient tel que sp cifi dans le paragraphe ci dessus Si des unit s internes ou des barrettes de m moire SIMM sont ajout es un poste de travail la classe du DOC de la machine risque d tre affect e Toutes les unit s internes et barrettes de m moire SIMM offertes par Sun et destin es tre utilis es sur un poste de travail Sun ont t soumises des essais Elles ne changeront pas la classe du DOC figurant sur le poste de travail si l installation est conform e aux instructions sp cifi es dans le Guide d installation Sun Si l utilisateur se procure des unit s et des barrettes de m moire ailleurs que chez Sun la classe du poste de travail d finie par le DOC risque d tre d favorablement affect e Canada 7 Avis concernant les syst mes appartenant la classe A du DOC Cet appareil num rique de la classe A respecte toutes les exigences du R glement sur le mat riel brouilleur du Ca
9. ed in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the Sun Installation Guide may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense 4 Netra ft 1800 Compliance and Safety Manual February 1999 European Union Notice English Products with the CE marking comply with the protection requirements of the following EU Directives m EMC Directive 89 336 EEC as amended by 93 68 EEC by application of the following harmonised standards EN 55022 1994 Electromagnetic Interference EN 50082 1 1997 Electromagnetic Immunity z Low Voltage Directive 73 23 EEC as amended by 93 68 EEC by application of the following harmonised standard EN60950 1992 AMD11 Safety of Information Technology Equipment Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures to correct this interference To Ensure Compliance The following additional components or accessories are required 1 Shielded cables having earthed metal shells shall be used for connection to all input output ports 2 The system must be reliably connected to earth Europe
10. nada 8 Electromagnetic Compatibility Information Canada Communications Canada i e the Department of Communications regulates digital devices similar to the FCC in the United States Every product should be labeled or provided with documentation that states the class of the product The DOC defines the environment in which a digital device should be used as the FCC does DOC Class A is for an industrial or a commercial area and DOC Class B is for a residential an industrial or a commercial area As it is with the FCC every peripheral of a system must meet DOC Class B levels in order for a system to be considered DOC Class B If any peripheral or the workstation is DOC Class A the system is DOC Class A and should not be used in a residential area An end user in Canada is responsible for ensuring that his system is suitable for its environment as stated in the above paragraph If single in line memory modules SIMMs or internal drives are added to the workstation the DOC Class of the machine could be affected All SIMMs and internal drives offered by Sun for use in a Sun workstation have been tested and will not change the DOC Class labeled on the workstation if installed per the instructions in the Sun Installation Guide If memory or drives are purchased from sources other than Sun the DOC Class of the workstation may be adversely affected DOC Class A Notice This Class A digital apparatus meets all requirements of the
11. or service and repair to ensure that safety features are maintained V If CD ROM is fitted Use of controls adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure 14 Netra ft 1800 Compliance and Safety Manual February 1999
12. phanumeric characters If it has this FCC ID mark it is Class B If any of the peripherals in your system is not marked with an FCC statement the equipment should not be used in a home because of the greater likelihood of interference to radio and television reception Contact the manufacturer of the peripheral if you have any questions Modifications If the end user adds single in line memory modules SIMMs or internal drives or PCI cards to the system the FCC Class of the machine could be affected All DIMMs and internal drives offered by Sun for use in a Sun product have been tested and will not change the FCC Class labeled on the product if it is installed per the instructions in the Sun Netra ft 1800 Installation Guide If memory drives or PCI cards are purchased from sources other than Sun the FCC Class of the system may be adversely affected Modifications not approved by Sun may void the authority granted by the FCC to operate the equipment Shielded Cables Connections between the system and other external equipment must be made using shielded cables earthed at both ends in order to maintain compliance with FCC radio frequency emission limits FCC Class A Notice Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operat
13. torisation pr alable et crite de Sun et de ses bailleurs de licence s il y en a Le logiciel d tenu par des tiers et qui comprend la technologie relative aux polices de caract res est prot g par un copyright et licenci par des fournisseurs de Sun Des parties de ce produit pourront tre d riv es des syst mes Berkeley BSD licenci s par Universit de Californie UNIX est une marque d pos e aux Etats Unis et dans d autres pays et licenci e exclusivement par X Open Company Ltd Sun Sun Microsystems le logo Sun AnswerBook Java le logo Jave Coffee Cup Netra et Solaris sont des marques de fabrique ou des marques d pos es ou marques de service de Sun Microsystems Inc aux Etats Unis et dans d autres pays Toutes les marques SPARC sont utilis es sous licence et sont des marques de fabrique ou des marques d pos es de SPARC International Inc aux Etats Unis et dans d autres pays Les produits portant les marques SPARC sont bas s sur une architecture d velopp e par Sun Microsystems Inc L interface d utilisation graphique OPEN LOOK et Sun a t d velopp e par Sun Microsystems Inc pour ses utilisateurs et licenci s Sun reconnait les efforts de pionniers de Xerox pour la recherche et le d veloppement du concept des interfaces d utilisation visuelle ou graphique pour l industrie de l informatique Sun d tient une licence non exclusive de Xerox sur l interface d utilisation graphique Xerox cette licence co
14. uvrant galement les licenci s de Sun qui mettent en place interface d utilisation graphique OPEN LOOK et qui en outre se conforment aux licences crites de Sun CETTE PUBLICATION EST FOURNIE EN L ETAT ET AUCUNE GARANTIE EXPRESSE OU IMPLICITE N EST ACCORDEE Y COMPRIS DES GARANTIES CONCERNANT LA VALEUR MARCHANDE APTITUDE DE LA PUBLICATION A REPONDRE A UNE UTILISATION PARTICULIERE OU LE FAIT QU ELLE NE SOIT PAS CONTREFAISANTE DE PRODUIT DE TIERS CE DENI DE GARANTIE NE S APPLIQUERAIT PAS DANS LA MESURE OU IL SERAIT TENU JURIDIQUEMENT NUL ET NON AVENU n EA Adobe PostScript Contents PartI Compliance Statements USA Electromagnetic Compatibility Information 3 European Union Notice 5 Canada 7 PartIl Safety Safety 11 iv Netra ft 1800 Compliance and Safety Manual February 1999 pant Compliance Statements USA Electromagnetic Compatibility Information System Classes Please read all of the following information to determine the class of system you have and the environment in which it should be installed and operated In the United States the Federal Communications Commission FCC governs the levels of electromagnetic emissions from a digital device Electromagnetic emissions can interfere with radio and television transmission To reduce the risk of harmful interference the FCC has established requirements for manufacturers of digital devices A manufacturer of a digital device must test and la
Download Pdf Manuals
Related Search