STD47 1.0 – Simple Telemetry Application Owner`s Manual
Contents
1. s Manual Page 3 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 1 Safety Information e The STD47 should be installed and set up only by qualified personnel e Connect a DC supply voltage in the range of 5 32 V to the STD47 The voltage supply must be secured by a fast 1 25 A fuse Insert a fast 1 25 A fuse into the wire for the positive supply voltage to protect the STD47 if you connect the STD47 directly to 5 32 V DC e If a power supply unit is used to supply the STD47 device it must meet the demands placed on SELV circuits Safety Extra Low Voltage in accordance with EN60950 When using batteries and accumulators adhere to the relevant regulations e The maximum permissible connection length between the STD47 and its peripherals is 3m e Never expose the STD47 to excessive humidity rain water acids etc e Use the STD47 indoors only e Never connect any voltage above 32 V to the STD47 and assure correct polarity e Please note that apart from correct setup and correct installation the STD47 depends always on the availability of a GSM network to operate correctly Aug 21 2003 Owner s Manual Page 4 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 2 Main Functions If set up accordingly the STD47 will perform the following three main functions 2 1 Start Up alarm message Upon power up the STD47 will send an SMS to the configured numbers The SMS may2. 5 are deleted during the quick Aug 21 2003 Owner s Manual Page 7 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG configuration pocedure Please refer to chapter 3 3 3 Expert configuration SMS for more detailed information about master alarm and client numbers After the quick configuration the STD47 must be restarted so that the SIM telephone book entries with the actual configuration can be read The SMS will be sent with the default text START UP ALARM and EVENT ALARM 1 or EVENT ALARM 2 for the respective conditions Note e Unlike in any other operating condition the STD47 will accept this first call and hang up after a few seconds This function will show you that the STD47 has accepted the configuration call e Torepeat this quick configuration process with an already configured STD47 it needs to be reset to factory setting again Please refer to section 3 3 2 Resetting the STD47 to factory setting below e The length of an input pulse and output pulse is set to 1 sec per default If you require other pulse timings please use the 3 3 3 Expert configuration SMS below 3 3 2 Resetting the STD47 to factory setting Resetting the STD47 to its factory setting is necessary if you want to delete the existing configuration data e g because you want to repeat the quick configuration procedure again or you want to configure another mobile phone as master There are
3. 7 5 brown 6 6 7 7 8 8 9 red 10 9 11 orange IN 2 12 yellow OUT 2 13 4 14 5 green GND 15 blue Aug 21 2003 Owner s Manual Page 26 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 7 3 Miscellaneous Dual band EGSM 900 1800 MHz System Operating temperature 30 C to 75 C Storage temperature 40 C to 85 C Weight lt 130g without accessories Compliant with ETSI GSM Phase 2 standards Output power Class 4 2W 900 MHz Class 1 1W 1800 MHz Please note The device is meant to work at low voltages only Never connect the device directly to mains 110V or 220V or similar as this may cause serious damage to the device and may harm you or other people Aug 21 2003 Owner s Manual Page 27 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 8 Accessories The following accessories are available from CEP AG for use with the STD47 8 1 Mains Power Adapter 220V This adapter is suitable for connecting the STD47 to mains power It is plugged in into the 6 Pin RJ11 connector of the STD47 the STD47 will start operation whenever power is applied with this adapter Aug 21 2003 Owner s Manual Page 28 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 8 2 DC Power Cable This cable can be used instead of the Mains Power Adapter if the STD47 should be connected directly to a DC power source 5V 32 V It se
4. GSM network the LED starts flashing approx every 2 seconds showing that it is ready to be configured now or ready to operate if it contains valid configuration data Please note that if the STD47 contains no valid configuration data it will cease operation after 3 minutes indicated by the LED remaining dark after that 3 minutes You will need to re apply power to it to wake it up again If the STD47 contains valid configuration data received either via a quick configuration call or an expert configuration SMS it is ready to receive your commands and to report events to you now Note If there is no GSM network available green LED remains on instead of flashing once every 2 seconds events and commands can not be reported or executed Aug 21 2003 Owner s Manual Page 13 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 5 Trouble Shooting This section shows typical error conditions and measures to relief them If you are not sure what may be the failure please check the following Failure Pictures and their possible causes in the order listed below Failure Picture Possible Cause Measures Note LED remains dark no power applied check power supply LED turns off after a few seconds no SIM inserted insert SIM SIM PIN not disabled or not set to 0000 disable SIM PIN function or set it to 0000 need to be done ina GSM phone LE
5. GSM phone If the SIM card is not configured this way the STD47 can not register in the GSM network and will therefore switch off approx 10 20 seconds after power up Please insert the SIM card in the STD47 only after setup of the SIM card as shown above If the SIM card PIN is not disabled the STD47 will use 0000 as PIN If this is not the correct SIM PIN it will result in a blocked SIM card after the 3 try This process is comparable to entering the wrong PIN on your GSM phone 3 times Such a SIM card would need to be recovered by entering the super PIN or PUK Aug 21 2003 Owner s Manual Page 6 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG Note It is recommended that you disable the voice mailbox and or the diversion to it for the SIM card used in the STD47 3 3 Setup of the STD47 The STD47 needs to know from which telephone it should accept commands and to which telephone it should report This is called configuration Note e A blank STD47 without a valid configuration factory setting will need a quick configuration call or an expert configuration SMS to know the GSM phone it reports to and it takes commands from A blank STD47 without configuration data will switch off 3 minutes after power was applied The green LED will be off then Therefore the quick configuration call or the expert configuration SMS must be issued
6. D remains continuously on no GSM network available change antenna position you may test this with your GSM phone by using the STD47 SIM card in it no GSM antenna connected connect appropriate GSM antenna STD47 registered in GSM network You may check if the STD47 is registered in the GSM network simply by calling it from a GSM phone There must be a short ringing tone before the STD47 terminates the call Attention if this is the first call the STD47 ever gets it will be interpreted as quick configuration call STD47 turns off after 3 min no valid configuration data stored in STD47 execute quick configuration call or expert configuration SMS may also apply after change of SIM card or manipulated entries of the SIM card STD47 is not reacting to quick configuration call does not accept the call STD47 is already configured already valid configuration data stored delete configuration data see 3 3 2 Resetting the STD47 to factory setting please note a successful quick configuration call is acknowledged by the STD47 by shortly picking up the receiver when you call Aug 21 2003 Owner s Manual Page 14 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG Failure Picture Possible Cause Measures Note STD47 is not reacting to an expert configuration SMS does not send a co
7. KQ 5 OUT 1 O VIN 0 4 A High Side Switch short circuit protected 6 GND Negative power ground input and return path for TO_IN and the extended inputs outputs Aug 21 2003 Owner s Manual Page 24 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 7 2 3 DB15 Connector Interface 1DCD 4IN 3 10 RI 13 DTR 2RD 5OUT 3 11 1IN 2 14GND 3TD 6DSR 12 OUT 4 15 ANA_IN Connector Pinout Pin Signal Dir Limits Description 1 not used 2 not used 3 not used 4 not used 5 not used 6 not used 7 not used 8 not used 9 not used 10 not used 11 IN 2 0 5 32V Digital input Vin gt 3 V Vit lt 2 8 V PullDown with 40KQ 12 OUT 2 O 32 V 0 25 A Low Side Switch short circuit protected 13 14 GND Ground connection and return path for the extended inputs outputs 15 not used Aug 21 2003 Owner s Manual Page 25 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG Cable Assembly Female P2 HDDB15 MALE P1 Legend 1 DB15 male connector to STD47 P1 2 DB9 female connector as standard RS232 connector e g directly to PC P2 3 9 conductor double shielded cable 4 7 conductor double shielded cable 5 Cable tie Pin connection at cable tie 7 flying leads Pinout Pinout Flying Signal P1 P2 leads Color 1 1 2 2 3 3 4 black
8. LED baa Antenna connector Access to SIM card RS232 serial and extended O connector Module viewed from the left side Mounting hole x2 o lt N Power supply and extended I O connector Audio connector Module viewed from the right side Aug 21 2003 Owner s Manual Page 21 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 7 1 2 Physical Dimensions Measurements are given in millimetres Aug 21 2003 Owner s Manual Page 22 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 7 2 Electrical Interface Antenna 50 Ohm FME male connector Signal cable to be connected to RS232 DB15 connector Status LED green LED on top SIM card reader 3V 5V mini SIM Powersupply 5 32 V DC on RJ11 connector 7 2 1 Block diagram GSM antenna headset Aug 21 2003 Owner s Manual Page 23 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 7 2 2 RJ11 Connector Interface 1 VIN 2 OUT 2 3 IN 1 4 TO_IN 5 OUT 1 6 GND Connector Pinout Pin Signal Dir Limits Description 1 VIN 5 32 V Positive power supply input 2 OUT 2 O 32 V 0 25 A Low Side Switch short circuit protected 3 IN 1 0 5 32 V Digital input Ve gt 3V Vic lt 2 8 V PullDown with 40KQ 4 TO_IN 0 5 32V Active low control line used to switch off the STD47 Vin gt 5 V V lt 2 V Power on t gt 0 2s PullUp to VIN with 20
9. STD47 1 0 Simple Telemetry Application Owner s Manual STD47 Simple Telemetry Application Owner s Manual CEP AG Table of Content 1 Safety IRON AMOI sooo Goce cern re cerece rece renee aeaee exe rece aae aat aee aat aae aat aae iat Eea 4 2 Main Functions sasacecncceonnesnasiasestcnkorbessubniesteniesaenecGoseetenseietatbecedpnieadientieananiaaweins 5 2 1 Start Up alarm message satschen caniodoadancntoncabiodeabanintanndasodaadabsntenddabetensdonetendtenns 5 2 2 Digital Output control nssenenenessnesenssssereeereeererererererrerereerrrrrrrrererreeeeereretnt 5 2 3 Digit llNpUt eVeNt rena EEEE 5 Se Setup Of th STD eiaeaen a e a aia aiaa iiaa ai 6 n Ai CT a r l EEEE 6 3 2 Setup of the GSM SIM card for the STD47 ceeeeeceeeeeeeeeeeeeeeeeeeeeeees 6 3 3 Setup of the STD47 icicanrientinicede ee econo 7 3 3 1 Quick configuration call scone eenen 7 3 3 2 Resetting the STD47 to factory Setting ennenen 8 3 3 3 Expert configuration SMS ooh cic rcctocesbecetecceccrceezencesecececececseeceeeceeecrseorece 8 4 Operating the STD scriescene a ere 13 5 Trouble SNOGUNG sereen rnan r E Ea Ea cies pede dp aariaa iaai 14 6 Sample Applications xcccacasatecssacdssetcenssanasostcacecencnteasosavacacosscastsesusevaconccarnceeateardes 16 6 1 GSM Alarm Adaptor for Burglar Alarm System cccccccececeeeeeeeeeeeeeeeeees 16 6 2 GSM remote control for garage door OPENel ccee
10. ceeceeeeeeeeeeeeeeeeeeeeeeeees 17 6 3 GSM remote sensing of a door open tampering switch 19 T Technical Data tistnsnestccntoteasansstnandatetniesrnsdsaxferstoan deeds iedeteactonrimsadsanimatnaeiedmaies 21 7 14 Mechanical Interface cansiccn eet nance ea eid 21 fate OVEM EW eee caittedeth bed sGeanendeth i mendes patents cemndtadstetecunies 21 7 1 2 Physical Dimensions i icc csccssaecsecscaicisiesdecseessduaddesidecsiensdeacdaaddeadcossdediens 22 7 2 Electrical Interface cccccceeeesseeeeeeceeeeeeeeseeeeeeeeeeeeeeeeessseeeeeeeeeeseeeaeeees 23 T24 lt BlockdiagiaM ssccrnnsenn a a 23 7 2 2 RJ11 Connector Interface vcccncinnconincinnanenncancme 24 7 2 3 DB15 Connector Interface cccccceeesseeeeeeeeeeeeeeeesseeeeeeeeeeeeeeeaeeeess 25 Poo WNMSCCIANGOWS sirsie a a aaae 27 Oe 0 eS E EOS e E A E E sees E E EE E via eeis deus tees Paacie 28 8 1 Mains Power Adapter 220V iicticcitenticeieneiditentisateeiierianlies ee 28 8 2 DC Power Cai 6 rpiiscsecsss cehacssancnradaastaredoactosedesndarsdonatosatinaiaiadsssdeaedsancopedonedes 29 8 3 GSM Dual Band Amlienm asiasecscccccecis cosscasicavecesccastea caetet eee coietccs 29 8 4 GSM Dual Band Antenna with direct Connection cceeeeeeeeeeeeeeeees 30 ADDrEVIA NOMS cccecsseacrsacveeprcesduasssasveaesrecpeausseureanceerreeeneenseauruntveiimeetsbusveai eera 31 Aug 21 2003 Owner s Manual Page 2 of 31 STD47 Simple Telemetry Appl
11. contain a default text if the device was configured by a Quick configuration call 3 3 1 or a user defined text if the device was configured by an Expert configuration SMS 3 3 3 This function is especially handy since an alarm condition can be signaled via GSM simply by applying power to the STD47 e g if the STD47 is connected in parallel to a siren or a flashlight it will transmit alarm SMS whenever the siren or the flashlight are activated 2 2 Digital Output control Upon incoming calls from phones with configured telephone number s it will operate the output switches OUT 1 and OUT 2 on the RJ11 connector and OUT 4 on the DB15 connector connected to the signal cables The incoming call will not be accepted by the STD47 it remains ringing and will be rejected by the STD47 after approx 3 sec No voice connection or valid call will be established So this function will be free of charge for the user 2 3 Digital Input event Upon applying the supply voltage to the digital inputs IN 1 on RJ11 connector and IN 2 on DB15 connector for at least 1 second default a SMS will be send to the configured master number The SMS may contain a default text if the device was configured by a Quick configuration call 3 3 1 or a user defined text if the device was configured by an Expert configuration SMS 3 3 3 All inputs are pulled to ground with a 40k resistor If an input was configured as inverted input by an Expert co
12. during the first 3 minutes after applying power e All configuration data is stored on the SIM card Therefore if you change the SIM card of an STD47 the configuration procedure must be repeated There are two ways to configure a STD47 3 3 1 Quick configuration call The quick configuration can be used only if the STD47 is in factory settings state taken right out of the box or after it has been reset to factory settings The quick configuration is very easy 1 Insert the correct configured SIM card see above connect a GSM antenna and power up the STD47 2 Wait for approx 20 seconds to allow the STD47 to initialize for the first time and to register in the GSM network 3 After that time the green LED should start flashing approx once every 2 seconds if not please refer to the trouble shooting section 4 Within the next 3 minutes call the STD47 from the mobile phone that you want to use to control the device and wait until the call is accepted After these quick configuration steps the STD47 is configured with the master number which is stored in the SIM phonebook at the first entry From now on the start up SMS and the event SMS will be sent to the mobile phone with the master number The STD47 will react on calls to control the outputs only from phones with either the master number or phones with client numbers at positions 9 60 in the SIM phonebook All alarm numbers phonebook entries 2
13. ect the 2 wires of the digital input IN 2 or IN 1 of the signal cable at DB15 or RJ11 and V IN at RJ11 to the appropriate switch of your door etc and apply DC power to the STD47 Give it a voice call quick configuration call from the GSM phone you want to make it report to Wait until the call is accepted by the STD47 the complete configuration is done now Option 1 GSM antenna 220V mains adaptor switch generates SMS when closed Option 2 220V mains GSM antenna adaptor switch generates SMS when closed Aug 21 2003 Owner s Manual Page 19 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG Now whenever somebody will close the switch you have installed e g connecting the 2 wires of the digital input of the signal cable to each other you will get an alarm SMS Needed components STD47 220V mains power adaptor Signal cable GSM antenna SIM card If you need to change the pulse length of the digital input or want to change the default text sent to you please refer to chapter expert configuration setup Aug 21 2003 Owner s Manual Page 20 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 7 Technical Data 7 1 Mechanical Interface 7 1 1 Overview The pictures below show the mechanical design of the module along with the positions of the different connectors and mounting holes The module case is made of durable PC ABS plastic
14. ed by the last 4 digits of the IMEl number of the STD47 This serves as a password The IMEl number is printed on the bottom of each STD47 Please be aware that a person who knows the IMEI number the telephone number of the inserted SIM card and the above protocol may configure the STD47 So you may want to keep these numbers in privacy Aug 21 2003 Owner s Manual Page 11 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG e The configuration data are stored at the phonebook entries 1 8 If you change or erase these phonebook entries the configuration may become invalid or corrupt Please reset the device to factory settings if this has happened e To get the configuration data send only the last 4 digits of the IMEI ina configuration message Aug 21 2003 Owner s Manual Page 12 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 4 Operating the STD47 After the power is applied the STD47 will start automatically beginning with an initialization phase This phase will include initialization of the hardware and reading configuration data from the SIM This phase will take about 20 seconds no operation is possible during this time The green LED is continuously on If the STD47 shuts itself off directly after that time there is no SIM card inserted or the SIM card requires a PIN which is set to a different value than 0000 After the STD47 has successfully registered in the
15. hone which shall receive the alarm SMS Wait until the call is accepted by the STD47 the complete configuration is done now Connect the power supply of the STD47 in parallel to the siren or flashlight of your home alarm system assuming the devices run at 12V DC or 24V DC The signal adapter is not needed in this application GSM antenna from burglar alarm system to siren 5V to 32 V DC Now whenever your siren or flashlight is activated the STD47 is powered as well and will send a power on alarm SMS to your GSM phone as soon as it has registered itself into the GSM network Needed components STD47 DC power cable GSM antenna SIM card If you want to change the default text of the SMS please refer to chapter expert configuration SMS Aug 21 2003 Owner s Manual Page 16 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 6 2 GSM remote control for garage door opener Objective You want to open your garage door via GSM instead of using the typical RF transmitter or a key switch Realisation Simply insert a SIM card with the SIM PIN set to 0000 or SIM PIN deactivated into the STD47 connect the 2 wires of the digital output OUT 4 or OUT 2 switch of the signal cable at DB15 or RJ11 to the appropriate input of your garage door drive the same input as you would use for a push button to open and close the door and apply DC power to the STD47 For contacting to the digital outp
16. ication Owner s Manual CEP AG Introduction The STD47 is a simple telemetry solution for remote control and remote sensing of digital signals via GSM This user manual is focusing in the functionality and the possible applications of the STD47 Depending on the accessories included in the package e g power supply adaptor GSM antenna signal cable normally no additional parts are necessary to operate the STD47 besides a valid SIM card If you want to step directly into the realisation of an application please refer to chapter 6 Sample Applications The STD47 is a CEP AG application based on SonyEricsson GT47 hardware extended by CEP AG SW to perform telemetry applications After a simple and quick configuration procedure the STD47 allows you to control various devices and applications remotely by your GSM phone and you are able to receive messages and alarms from your devices and applications The STD47 identifies and authorizes your GSM phone by its telephone number CLIP function Calling Line Identification Presentation Configuration can be done in 2 ways e quick configuration call The out of the box STD47 learns by a simple telephone call from a GSM phone to which telephone number it shall report and from which telephone number it can be controlled e expert configuration SMS The configuration is done by sending an SMS containing the configuration data as specified below Aug 21 2003 Owner
17. mbers the expert configuration SMS allows to configure up to 52 additional Client Numbers Incoming calls from the Client Numbers will control the digital output in the same way like an incoming call from the Master Number but events will still be reported only to the Master Number and to the Alarm Numbers Master Number Alarm Numbers reserved Client Numbers phone book entry phone book entry phone book entry phone book entry 1 2 45 6 and 8 9 60 The procedure expert configuration SMS is more complex than the quick configuration but has the following advantages e message texts for start up and events can be defined by the user e start up messages can be deactivated e output pulse length can be configured in seconds e configuration of up to 57 telephone numbers from which the STD47 output can be controlled 1 Master Number and 4 Alarm Numbers and 52 Client Numbers e input pulse length that is detected as event can be configured in seconds e digital input can be inverted e expert setup can be done at any time also with a formerly configured STD47 e expert setup can be done remotely Aug 21 2003 Owner s Manual Page 9 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG The structure of the expert configuration SMS is as follows The first 4 characters of the text field of the SMS must contain the last 4 digits of the STD47 IMEI number The IMEI number i
18. nfiguration SMS 3 3 3 the inputs must be connected to the supply voltage In case of an event the connection to the supply voltage must be opened for at least 1 second default The duration the inputs must be switched default value 1 second to generate a SMS can be configured by an expert configuration SMS Aug 21 2003 Owner s Manual Page 5 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 3 Setup of the STD47 3 1 General The STD47 recognizes the GSM phone you want to use to control it by its telephone number CLIP function Therefore it is necessary that you don t suppress the transmission of your telephone number Please make sure your GSM phone is not set to incognito or suppress own telephone number when controlling or configuring the STD47 To test this simply make a phone call from your GSM phone to a friend s phone If he can see your telephone number in the display of his phone everything is fine 3 2 Setup of the GSM SIM card for the STD47 It is recommended to use a SIM card that needs no PIN entry in that case no further actions are required If a SIM card is used that needs a PIN entry before registering in the GSM network this function should be deactivated not possible with some SIM cards alternatively the PIN can be set to 0000 possible with all SIM cards This can be done e g with a normal GSM phone Please refer to the owner s manual of the used
19. nfirmation reply but is registered in the GSM network LED flashing once every 2 seconds SMS is not delivered to the STD47 sometimes transmission of SMS takes a few or more seconds please try to call the STD47 to make sure it is registered in the GSM network SMS memory of STD47 SIM card is full therefore it can not receive any additional SMS put SIM card in a normal GSM phone and delete some or all of the SMS in the SIM card memory STD47 is not reporting and not reacting to any configuration or command but is registered in the GSM network your GSM phone does not transmit its telephone number therefore the STD47 can not identify it disable incognito or suppress own telephone number of the SIM card in your GSM phone Aug 21 2003 Owner s Manual Page 15 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 6 Sample Applications The following section explains the wiring and setup for some typical applications Please refer to chapter 7 2 Electrical Interface for detailed contact pin out 6 1 GSM Alarm Adaptor for Burglar Alarm System Objective You want to get an SMS to your GSM phone when your home burglar system is activated Realisation Simply insert a SIM card with the SIM PIN set to 0000 or SIM PIN deactivated into the STD47 and apply DC power to it Give it a voice call quick configuration call from the GSM p
20. rves the pins of the RJ11 connector on one end and is open on the other end When using this DC Power Cable please make sure to apply the wiring scheme pointed out in the chapter technical data Wiring scheme please see 7 2 Electrical Interface 8 3 GSM Dual Band Antenna This antenna can be connected directly to the STD47 by its FME female connector It contains a magnet in its foot of easy mounting on metal surfaces rA Aug 21 2003 Owner s Manual Page 29 of 31 STD47 Simple Telemetry Application Owner s Manual C E P AG 8 4 GSM Dual Band Antenna with direct connection This antenna can be connected directly to the STD47 by its FME female connector without any cabling in between Aug 21 2003 Owner s Manual Page 30 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG Abbreviations CLIP Calling Line Identity Presentation IMEI International Mobile Equipment Identity PIN Personal Identification Number SIM Subscriber Identity Module SMS Short Message Service Aug 21 2003 Owner s Manual Page 31 of 31
21. s printed on the bottom of each device With those 4 digits and the command identifiers the following commands could be used with the STD47 List of commands C 0682 A IMEI 350496 83 001275 9 MOTO A TTT S N S48 61TJN TYPE 618 583 BYV KRD 102 32 1 RIA Made in Taiwan AAAAA O2W5 Command Description Command Command Syntax and Values identifier Reset to factory settings R R Enable Disable Power Up S S 1 S 0 message Output pulse width O O lt pulsewidth gt 1 99 in seconds Input pulse width I I lt pulsewidth gt 1 99 in seconds Master Number C C 1 lt number gt read only Alarm Client Numbers C C lt index gt lt number gt index 2 5 index 9 60 Power Up message text M M lt text gt max 16 characters Event message text E E lt index gt lt text gt index 1 2 max 16 characters Invert Input V V 0 use input as normal V l invert input Read phone book entry G G lt id gt index 2 5 index 9 60 Delete phone book entry X X lt id gt index 2 5 index 9 60 Read configuration data lt empty gt lt empty SMS gt It is possible to issue one several or all possible commands in the same SMS separated by a blank Each command starts with the command identifier followed by a colon and in most cases by command values Apart from the reset to factory settings all commands are clo
22. sed by a dot Aug 21 2003 Owner s Manual Page 10 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG Examples IMEI 350496 83 001275 9 read from the bottom of the STD47 see picture Example 1 Power Up SMS enabled pulse lengths of 10s for output and 60s for input configured Content of SMS to be sent 2759 Sile 0 10 1 60 Example 2 Reset to factory settings Content of SMS to be sent 2799 R Example 3 Setting Client Numbers C 1 is reserved for the Master Number set by CLIP Content of SMS to be sent 2759 C 2 4491721234561 3 4 491721234562 C 4 491721234563 C 5 4 491721234564 Example 4 Configure message text strings for Power Up SMS and Event SMS Content of SMS to be sent 2759 M CeTEC POWER ON E 1 CeTEC Alarm 1 E 2 CeTEC Alarm 2 Configuration acknowledge SMS sent by STD47 as reply 2759 S 1 V 0 0 10 1 60 C 1 491721234560 C 2 491721234561 C 3 491721234562 C 4 491721234563 C 5 4917212345604 M CeTEC POWER ON E 1 CeTEC Alarm 1 E 2 CeTEC Alarm 2 assuming the expert configurations SMS was sent from a GSM phone with the phone number 49 172 1234560 Note e The reception of a correct configuration SMS will be acknowledged by a Status SMS to the new Master Number after a few seconds containing the configuration data A reset to factory settings SMS will not be acknowledged e An expert configuration SMS needs to be authoriz
23. two ways to reset an STD47 to factory setting e Delete the SIM card phone book entries at least 1 to 8 Most GSM phones support this as a single command Simply take the SIM card out of the STD47 insert it into a GSM phone and delete the entire phone book of the SIM card e Send a reset to factory setting SMS to the STD47 Please refer to section 3 3 3 Expert configuration SMS below Note The reset will not change or delete the phone book entries 9 60 3 3 3 Expert configuration SMS If you do not need the extended features of the expert configuration we recommend you to perform the quick configuration call The GSM phone number stored at the first position in the SIM phonebook is called Master Number it is allowed to control the digital output and gets start up and event SMS This number can only be set by the CLIP telephone number of calling party of an incoming quick configuration call or by the sender CLIP of the expert configuration SMS Aug 21 2003 Owner s Manual Page 8 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG In addition to this Master Number the expert configuration SMS allows to configure up to 4 additional Alarm Numbers Incoming calls from the Alarm Numbers will control the digital outputs in the same way like an incoming call from the Master Number events and startup will also be reported like to the Master Number In addition to Master and Alarm Nu
24. ut you could use either the RJ11 or DB15 connector Give it a voice call quick configuration call from the GSM phone you want to control it from Wait until the call is accepted by the STD47 the complete configuration is done now Option 1 GSM antenna 220V mains adaptor to garage door drive control unit push button closed when activated by STD47 Option 2 220V mains GSM antenna adaptor to garage door drive control unit push button closed when activated by STD47 Aug 21 2003 Owner s Manual Page 17 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG Now with every call from that GSM phone to the STD47 it will control your garage drive Needed components STD47 220V mains power adaptor Signal cable GSM antenna SIM card If you need to change the pulse length of the digital output please refer to chapter expert configuration setup If you need to control the STD47 by more than one GSM telephone up to 5 please refer to chapter expert configuration SMS Aug 21 2003 Owner s Manual Page 18 of 31 STD47 Simple Telemetry Application Owner s Manual CEP AG 6 3 GSM remote sensing of a door open tampering switch Objective You want to receive an alarm SMS whenever somebody opens a certain door closes a certain switch etc Realisation Simply insert a SIM card with the SIM PIN set to 0000 or SIM PIN deactivated into the STD47 conn
Download Pdf Manuals
Related Search