Home

DP9270/90 RS-232 Commands

1. C3A 43h 33h 41h POINTER RIGHT C3B 43h 33h 42h POINTER LEFT C3C 43h 33h 43h POINTER UP C3D 43h 33h 44h POINTER DOWN C3F 43h 33h 46h SELECT KEY C43 43h 34h 33h FREEZE ON C44 43h 34h 34h FREEZE OFF C46 43h 34h 36h ZOOM DOWN C47 43h 34h 37h ZOOM UP C4A 43h 34h 41h FOCUS DOWN C4B 43h 34h 42h FOCUS UP C5D 43h 35h 44h LENS SHIFT UP C5E 43h 35h 45h LENS SHIFT DOWN C70 43h 37h 30h FULL LAMP MODE 2 Lamp Mode 1 Lamp Mode When switching from HALF LAMP MODE 1 to HALF LAMP MODE 2 C71 43h 37h 31h HALF LAMP MODE 1 and vice versa there will be a 30 second FULL MODE transition period 1 Lamp Mode When switching from HALF LAMP MODE 2 to HALF LAMP MODE 1 C72 43h 37h 32h HALF LAMP MODE 2 and vice versa there will be a 30 second FULL MODE transition period C89 43h 38h 39h AUTO PC ADJUST Auto adjust Total Dots Fine Sync and Position C8A 43h 38h Ath PRESENTATION TIMER C8E 43h 38h 45h KEYSTONE C8F 43h 38h 46h KEYSTONE PROXIMA PRO AV 9500 50 STATUS REQUEST COMMANDS Status request commands are used to poll the projector to obtain setting and status information COMMAND ASCII HEX PROJECTOR STATUS READ CRO 43h 52h 30h RESPONSE DETAILS 00 30h 30h Projector lamp is ON 80 38h 30h Projector is in Standby mode 40 34h 30h Projector lamp just powered ON going throug
2. oxima jr InFocus Professional Series Pro AV 9500 50 Serial Communications The Proxima Pro AV 9500 50 RS 232 serial communications protocol allows control of the projector by an external control system such as AMX or Crestron Connecting Projector to Control System PC Use a standard null modem cable available from most computer Electronics stores or use the cable pinout diagram Fig 1 to assemble custom length cable Fig 1 Null Modem Cable DB9 DB9 Female Female a rm Receive Data __ 5 4 3 2 4 j Transmit Data ae 3 VUDG Ground DDPS Note To ensure proper operation connect only properly wired RS 232 serial communication cables to the projector s control port serial port IN serial port OUT id a a O COMMUNICATIONS PORT SETTINGS Baud Rate Data Bits Stop Bits Parity Flow Control 19200 8 1 None None Note The projector keypad IR remote and RS 232 external control will function simultaneously 1 of 6 PROXIMA PRO AV 9500 50 CONTROL COMMANDS Control commands are used to adjust various projector characteristics or to emulate key presses from the built in keypad or IR remote control FORMAT ASCII code Control Sys gt Projector C 0 1 CR Response ASCII code l ASCII Code cofi R HEX Code Notes The Proxima Pro AV 9500 50 does NOT require Line Feed OA hex in the command syntax Delay Recommendations 10ms between chara
3. RS 232 input of the first projector taking the RS 232 output of that projector and connecting it to the RS 232 input of the second projector and so on Setting the Projector s Address Setting individual address numbers for each projector 1 Turn projector on 2 Enter the service menu by simultaneously pressing the MENU and IMAGE buttons on the projector keypad and hold for 2 seconds 3 Change to service Group 10 by using the left right arrow keys on the projector or remote control Change to No 3 by using the up down arrow keys on the projector keypad or remote 4 Once at Group 10 No 3 adjust the data value to set the projector s address number Press the VOLUME up down button on the projector keypad or remote control to change data value The data value set must be different for each projector to be controlled and can be a number in the range of 0 999 5 Exit the service menu and turn the projector off by pressing the POWER button twice Allow the projector to cool down and power it back up for the new address to take effect Sending commands Add A specific address number to the beginning of RS 232 command Example 1 Controlling a single projector in the daisy chain To switch only the projector which was assigned address number 15 to INPUT2 Send command A015C06 CR Where A Specifies that a unique projector address is being used 015 Projector s address number entered as a 3 digit base 10 number C06 Select INP
4. UT 2 command CR Carriage return OD hex Note Projector s response will be the same as if only one projector is connected to the control system PC Example 2 Broadcasting commands to all projectors To power ON all projectors at once Send command AFFFC00 CR Where A Specifies that a unique projector address is being used FFF Is the 3 digit address number used to address all the projectors in the chain C00 POWER ON command CR Carriage return OD hex Note There will be no projector responses generated to broadcast commands 6 of 6
5. cters 100ms between commands Responses to Control Commands 06h ODh ACK CR Command accepted and executed 3Fh ODh CR Command not recognized EXAMPLES POWERON asc C 0o 0 CR Projector response may contain Line Feed Note Display should be set to OFF in Setting Menu to prevent OSD message displays Proxima Pro AV 9500 50 COMMAND CODES COMMAND ASCII HEX FUNCTION NOTE coo 43h 30h 30h POWER ON C01 43h 30h 31h POWER OFF C02 43h 30h 32h POWER OFF Power Off will appear on screen C05 43h 30h 35h INPUT 1 SELECT C06 43h 30h 36h INPUT 2 SELECT C07 43h 30h 37h INPUT 3 SELECT C09 43h 30h 39h VOLUME Increments projector Volume by one COA 43h 30h 41h VOLUME Decrements projector Volume by one COB 43h 30h 42h AUDIO MUTE ON COC 43h 30h 43h AUDIO MUTE OFF COD 43h 30h 44h NO SHOW ON Video Mute ON COE 43h 30h 45h NO SHOW OFF Video Mute OFF COF 43h 30h 46h AV REGULAR SIZE Sets display to 4 3 aspect ratio C10 43h 31h 30h AV WIDE SIZE Sets display to Anamorphic aspect ratio C1C 43h 31h 43h MENU ON Displays main Menu on the screen 2 of 6 C1D 43h 31h 44h MENU OFF Removes main Menu from the screen C1E 43h 31h 45h CLEAR DISPLAY Clears On Screen Display C27 43h 32h 37h IMAGE C30 43h 33h 30h DIGITAL ZOOM C31 43h 33h 31h DIGITAL ZOOM
6. h 30 sec Countdown 20 32h 30h Projector lamp just powered OFF and is cool down cycle 02 30h 32h No key input 10 31h 30h Power failure 3 of 6 08 30h 38h Temperature Warning and power is ON 28 32h 38h Projector in Cool Down cycle after power failure 88 38h 38h Projector operating normally after temperature warning occurred 04 30h 34h Lamps OFF in Power Management mode 24 32h 34h Cool down cycle after Power Management shutdown COMMAND ASCII HEX ACTIVE INPUT READ CR1 43h 52h 31h RESPONSE DETAILS 1 31h Input 1 currently selected and being displayed 2 32h Input 2 currently selected and being displayed 3 33h Input 3 currently selected and being displayed COMMAND ASCII HEX LAMP TIMER READ CR3 43h 52h 33h RESPONSE DETAILS Two sets of four digit numbers representing total number of accumulated lamp hours for XXXX XXXX each Lamp 1 and Lamp 2 COMMAND ASCII HEX ORIENTATION READ CR4 43h 52h 34h RESPONSE DETAILS 11 31h 3th Front Screen Floor Mount 00 30h 30h Front Screen Ceiling Mount 01 30h 31h Rear Screen Floor Mount 10 31h 30h Rear Screen Ceiling Mount COMMAND ASCII HEX TEMPERATURE READ CR6 43h 52h 36h RESPONSE DETAILS Temperature at thermal sensor near LCD panel Space space Temperature at thermal XX X XX X sensor near lamp Units are in Celsi
7. us Intended for service purposes only 4of6 COMMAND ASCII HEX LAMP MODE READ CR7 43h 52h 37h RESPONSE DETAILS 00 30h 30h FULL LAMP MODE All Lamps OFF 01 30h 31h FULL LAMP MODE Lamp No 1 ON Lamp No 2 OFF 02 30h 32h FULL LAMP MODE Lamp No 2 ON Lamp No 1 OFF 03 30h 33h FULL LAMP MODE All Lamps ON 10 31h 30h HALF LAMP MODE 1 All Lamps OFF 11 31h 31h HALF LAMP MODE 1 Lamp No 1 ON Lamp No 2 OFF 20 32h 30h HALF LAMP MODE 2 All Lamps OFF 22 32h 32h HALF LAMP MODE 2 Lamp No 2 ON Lamp No 2 OFF COMMAND _ ASCII HEX PC TYPE READ CR9 43h 52h 39h RESPONSE CSETANWS STAND BY Projector is powered OFF and is in Stand by mode AV Mode Current source is Video Go PC adj PC system is set to AUTO No signal No source on current input 2K gt K Kk K Where gt gt gt K is name of the current RGB source signal type COMMAND TEX MUTE STATUS READ 43h 52h 41h RESPONSE DETAILS 30h 30h OD Video and Audio Mute are OFF 30h 31h OD Video Mute is ON 30h 32h OD Video Mute is OFF 30h 33h OD Video and Audio Mute are ON 5 of 6 Controlling Multiple Projectors Multiple projectors can be controlled from a single control system PC by using the RS 232 loop through feature in the Proxima Pro AV 9500 9550 This can be done by daisy chaining connecting the control system PC RS 232 output to the

DP9270/90 RS-232 Commands

Contents

Download Pdf Manuals

Related Search

Related Contents