- PrehKeyTec
Contents
1. Turns the Auto Sensing Brightness Adjustment circuit ON or OFF Menu shows sensed light level and brightness setting as a percent age of full scale Same setting as Brightness in Contrast and Brightness menu when Auto DIM is OFF With Auto DIM ON brightness is now controlled by the light sensor located at top center of the front bezel See additional discussion of the Auto Sensing Brightness Adjustment Power OSD Lock Unlock Note There is no menu graphic for this feature The Power OSD lockout menu is separate from the main OSD 1 Access this feature by first pressing the MENU button to access the main OSD 2 While the main OSD is displayed press and hold the MENU button The main OSD will disappear 3 While continuing to hold the MENU button down momentarily press the POWER button The POWER OSD lockout menu will appear 4 Press the ENTER button to alternately select OSD or POWER and use the UP and DOWN buttons to toggle your selection between UNLOCK the default and LOCK OSD LOCK defeats all normal access to the OSD including the Direct Access shortcuts to Brightness Audio and Video Auto Adjust To access the OSD when in OSD LOCK press and hold MENU and while holding MENU down momentarily press POWER POWER LOCK defeats the operation of the POWER button This feature in addition to preventing casual vandalism of the system allows the MCI Touch Monitor to power up properly when the system or MCI Touch Monitor is powe2. at preh keytec com Touchscreen and Peripherals Driver Installation Drivers for all supported operating systems are contained on the Preh Install Disk To install drivers follow the procedures below as appropriate Touchscreen support is provided for Windows 98 Me NT 2000 XP DOS and Linux kernels 4 2 18 and above The MSR and Customer Display which are USB devices are currently supported under Windows platforms only Support for Linux will be provided in the future Contact Preh TechSupport for further information Windows 98 Me NT 2000 XP Installation e If you are using a USB data interface disconnect it from the computer before proceeding Connect the touchscreen cable if using a serial interface MCI 15 only Insert the disk in your drive If AutoRun does not start the installation double click the Setup program in the CDROM folder e Follow the instructions pertaining to your particular product configuration and check the appropriate boxes in the Select Features page to install drivers for the peripherals you have The POS demo program may be installed now or at any time in the future e Ifthe installation program does not restart your computer shut down connect the USB cable if used and restart e After restart the touchscreen controller and other USB devices if present the MSR and Customer Display will be found by Windows and the drivers automatically installed for them e Find the Preh M
3. the accessory kit included with your monitor Please note that all Preh MCI Touch Monitors that include an MSR or MSR Customer Display also have an internal USB hub to interface with the peripheral devices As a result the display will have only one USB cable which supports both touch data and the MSR Customer Display data Also two additional User USB ports are available on the display and these ports may be used to connect additional USB devices to your system such as a mouse bar code reader etc Power Video and Audio Connect the power video and if desired audio cables to the monitor using the Quick Set up Guide for assistance Mounting You may simply place the monitor upright on the base of the desk stand However if you wish to use your monitor in any other way than resting it on its stand on a flat surface you will need to either e Attach the stand to a countertop or wall e Dismount the display chassis from the stand and use the VESA mounting holes on the chassis to attach the display to an arm or other mount Note Connect the cables to the monitor before attaching the stand to a countertop or a wall if access to cable connections will be restricted when the stand mounting is complete To attach the stand to a countertop or wall MCI 15 e VESA The four holes near the middle of the base plate are VESA compatible with spacing of 75 mm center to center Use these holes to bolt the stand from the back side e K
4. AE EE 17 UT Warning To prevent the risk of fire or shock do not expose this product to rain o moisture Warning To avoid electric shock do not open or disassemble this product There are no user serviceable parts in this product Refer all service questions to Preh or a qualified service provider Introduction Congratulations on your purchase of a Preh MCI Touch Monitor This manual covers all models of the Preh MCI Touch Monitor 15 series of touch monitor products Preh Keytec has brought together a team of experienced developers from the touch industry to create what we believe to be the finest Touch Monitors available in the industry today Your Preh MCI Touch Monitor combines outstanding flat panel display design the most needed features for typical touch POS and medical applications and the best touchscreen components to deliver a product of superior performance and value We welcome your comments on our products and our company For the latest product information see our web site at http www preh keytec com or www prehusa com Americas As you read this manual you may encounter words or terms associated with display touchscreen or touch applications that you are not familiar with Many of the words unique to this industry have been italicized on first use in this manual Definitions of these words have been included in the Glossary Product features of the Preh MCI Touch Monitor include 5 AMTFT LCD panel e A
5. CI Touch Monitor Settings icon on the desktop or in Control Panel and use the features under the appropriate tabs to configure the operation of the touchscreen for your application and if necessary to calibrate the touchscreen to the display image e The MSR if present is configured for keyboard emulation by default It should work identically to Keyboard wedge readers in all applications Contact Preh TechSupport at techsupport prehusa com Americas only or support preh keytec de if this format is not suitable for your application e The Customer Display while hardware interfaced as a USB device is equivalent to a serial display for programming purposes Contact Preh Technical Support for programming information on this device DOS Installation e See specific procedures in DOS section of disk Linux Installation e See specific procedures in Linux section of disk e Kernels 2 4 18 and above corresponding to RedHat Linux versions 8 and 9 are supported e Source code is available on request e For additional information contact Preh at techsupport prehusa com Americas only or support preh keytec de MCI 15 Specifications Monitor Part Numbers MCI 15 MCI 15M MCI 15MD Display 15 Color AMTFT LCD Color Black Touchscreen Technology 5 wire resistive Active Screen Dimensions Horizontal 11 9 304 mm Vertical 8 9 228 mm Monitor Dimensions With Stand Height 13 9 35 22 cm Width 15 5 39 37 cm
6. Depth 8 25 20 95 cm Without Stand Height 12 9 32 68 cm Width 15 5 39 37 cm Depth 2 5 6 36 cm Weight MCI 15M Actual 15 Ib 6 8 kg Shipping 21 Ib 9 5 kg Brightness LCD 250 nit With touchscreen 200 nit Resolution Native 1024 x 768 at 60 70 or 75 Hz Supported 800 x 600 at 56 60 72 and 75 Hz 720 x 400 at 70 Hz 720 x 350 at 70 Hz 640 x 480 at 60 72 and 75 Hz Viewing Angle Horizontal 120 Total 60 left right Vertical 105 Total 60 up 45 down Contrast Ratio 400 to 1 Scanning Frequency Horizontal 31 5 60 kHz Vertical 56 75 Hz Video Input Analog RGB VGA Analog RGB with sync on green Video Bandwidth 80 MHz Input Video Format VGA SVGA XGA analog Power Supply Voltages Internal DC supply AC input 100 240VAC 50 60 Hz Power Dissipation 30 W max Temperature Operating 0 C to 40 C Storage 30 C to 60 C Humidity Operating 20 to 80 non condensing Storage 5 to 90 non condensing External Connections Power IEC320 Standard AC inlet MCI 15T Specifications Audio Standard 3mm Stereo Jack Monitor Part Numbers MCI 15T C2TR2 Video HD15 VGA MCI 15T C2TR4 Touch Interface Standard USB series B receptacle MCI 15T C1TR4 Standard DB9 F Serial MCI 15 only Display 15 Color AMTFT LCD Connectivity Two USB Type A input ports MCI 15M amp Color MCI 15T C2RT2 Black POS Options Magstripe Reader 3 Track Reader with Power and Error MCI 15TC2RT4 Black Customer Display 2 x 20 VFD Display with Dual Axis til
7. Erel KeyTec Germany and rest of the world Preh GmbH An der Stadthalle D 97616 Bad Neustadt a d Saale Germany Phone 49 0 9771 92 0 Fax 49 0 9771 92 300 marketing preh keytec de www preh keytec com USA Canada and Latin America Preh Electronics 590 Telser Rd Unit B Lake Zurich IL 60047 Phones 800 577 7734 847 438 4000 Fax 847 438 5522 prehsales prehusa com www prehusa com France Preh France Eragny Parc Bat Californie BP231 Eragny 95615 Cergy Pontoise France Phone 33 0 1 39 09 99 00 Fax 33 0 13909 99 09 contact preh fr MCI Touch User s Guide MCI 15T Copyright 2005 Preh Keytec All Rights ReservedNo part of this document may be reproduced photocopied transmitted translated to another language or stored on a computer or imaging or information retrieval system in any form whether electronic mechanical optical or otherwise without the prior written permission of Preh Keytec Preh DisclaimerThe information contained in this document is subject to change without notice and should not be construed as a commitment or obligation by Preh Keytec Preh Keytec assumes no responsibility for any errors that may appear in this document and does not make any expressed or implied warranty with regard to this document including but not limited to any implied warranty of merchantability or fitness for a particular purpose Preh Keytec shall not be liable for any incidental or
8. ce end to connect to your touch display Notice Unless your Preh MCI Touch Monitor has a serial data interface or you are connecting this MCI Touch Monitor to a computer that already has Preh touchscreen MSR and Customer Display drivers installed please leave the USB cable disconnected until the appropriate drivers for your computer s operating system have been installed On Screen Display Controls The following table shows the OSD and Power control buttons located on the right side of the display and both the Normal and Direct Access functions of these buttons The Direct Access features can be used by pushing the corresponding button without entering the OSD Menu first For example you may access the Display Brightness feature through Direct Access by simply pushing the UP button Direct Access Button Symbol Button Name Function Normal 1 E Menu Displays Exits OSD Menu 2 A Up Increases selected item value Display brightness 3 v Down Decreases selected item value Audio ON OFF 4 J Enter Selects highlighted menu item Video auto adjust Parm 5 O Power Turns all display power ON OFF Display Setup Use the OSD buttons to set up the display 1 Turn on the display with the POWER button 2 The display will initially be set to properly display the native resolution for the LCD panel which is 1024 x 768 pixels If your computer outputs a video signal at another resolution further adjustment than described in this secti
9. consequential damages arising from or in connection with the use of this document or the product which it describes whether or not that use is consistent with any statement in this document TrademarksPreh Preh MCI Touch Monitor MCI 15 MCI 15M MCI 15MD MCI 15T Auto Sensing Brightness Adjustment and the Preh logo are trademarks of Preh Keytec Inc Trademarks of all other products mentioned in this document are owned by the products respective companies Contact Information Preh Electronics Inc USA prehsales prehusa com Preh Keytec Gmbh Germany and Rest of the world marketing preh keytec de Preh France France contact preh fr Preh Keytec MCI Touch Product Manual Table of Contents Usage INOUC Cs tecectrcndecctanticanaedteustadsensedensitensnedndeduatedesaeodonased 4 INTFTOCUCTION ccccccecceccceccccccccecccccecceccesuecuccueecuesuesuesuesaeeas 4 Connections and Installation ccc ccccceccecccececcecceceeeecs 5 Data Connection Power Video and Audio Mounting Display Setup and On Screen Display OSD 008 6 On Screen Display Controls Display Setup Display Resolution OSD Menu and Functions Power OSD Lock Unlock Auto Sensing Brightness Adjustment Touchscreen and Touchscreen Drivers cceceeseceeeeeeeees 9 Touchscreen Features and Use Touchscreen and Peripheral Drivers Driver Installation 0 611 672 6 pene eee no eee en 11 GOSS 6 Ane er eo 15 ALU I E E
10. d is increasingly replaced by another method called USB see below USB Acronym for Universal Serial Bus Acommon method for interfacing peripheral equipment to computers It has the advantages over other serial data transmission standards of higher speeds and the ability to connect many devices to the same port on a computer VESA Acronym for Video Electronics Standards Association An industry trade group that promotes interoperability standards within the video and computer industry The VESA mounting pattern 75mm for displays is used by your Preh MCI Touch Monitor on the base and chassis allowing the monitor to be quickly attached to standard swing arms and mounting plates Preh Keytec Product Warranty Preh Keytec warrants that the Products will conform to the Specifications and be free from defects in material and workmanship for three 3 years from date of shipment 3 years warranty applies only for US customers For Europe and other countries please contact marketing preh keytec de for more information Customer shall contact Preh Keytec immediately upon discovery of any defects within the warranty period Products must be returned to Preh Keytec within thirty 30 days of Preh Keytec s receipt of warranty claim notice and only after receiving Preh Keytec s authorization to return products in accordance with Preh Keytec s Product Return Policy In the case Customer needs fast turnaround for product replacement Preh Keytec wil
11. display chassis Top or bottom access to countertop mounting holes Kensington lock connection on chassis Broad range of vertical tilt 5 to 90 Two built in 1W baffled speakers Approvals UL cUL TUV GS FCC Class B 3 Years warranty In the US Glossary AMTFT Acronym for Active Matrix Thin Film Transistor This is the type of liquid crystal display panel used in essentially all computer flat panel displays today Calibrate For touchscreens calibrate is the common term for the process that is really video alignment A touchscreen and its controller have a coordinate system that are usually not identical to the coordinate system of the video display of the host computer By displaying reference points on the MCI Touch Monitor through the calibration program and touching those reference points the MCI Touch Monitor coordinate system is scaled to that of the computer Color temperature Color temperature is a simplified way to characterize the spectral properties of a light source and is the temperature you would heat a theoretical black body source to radiate light of the same visual color For example low color temperature like 3200 K implies warmer more yellow red light while high color temperature like 9300 K implies a cooler more blue light Daylight has the 3200 K temperature mentioned near dawn and evening and a higher one during the day The standard unit for color temperature is
12. e magnetic stripe reader Keyboard wedge An MSR unit that connects to a computer keyboard port with a cable that also connects the standard keyboard thus a keyboard wedge LCD Acronym for Liquid Crystal Display The most common technology used in flat computer displays today Liquid crystal molecules a very complex chemical engineered for this function sandwiched between a combination of flat glass color filters and polarizers pass or block light in response to electrical signals applied by the display electronics The result is a very sharp bright display that is very thin and uses little power compared with a CRT or tube type monitor Lux The standard unit for illuminance is lux Ix which is lumens per square meter Im m2 1 lux 10 764 footcandle Common room lighting is 100 1000 lux MSR Acronym for Magnetic Stripe Reader A device that reads information encoded in the magnetic stripes on the back of a credit card etc The process is essentially identical to the operation of a cassette tape player Native resolution The resolution of a digital flat panel display that actually describes how many pixels are in each row and column of the display and which is the resolution that the display is optimized for Your 15 Preh MCI Touch Monitor has a native resolution of 1024 x 768 which means that the LCD panel has 1024 pixels on each row and has 768 rows Each element of video information received from the computer disp
13. er relatively large radius styli However hard objects with sharp edges can easily damage the touchscreen Avoid the use of ball point pen barrels with the tip retracted microball pens keys rings coins and metal tableware e Cleaning The touchscreen may be cleaned with common glass cleaners but do not use cleaners with abrasives Comet BonAmi etc The best procedure for cleaning the screen is to apply your cleaner to a soft cloth or paper towel and wipe the touchscreen until contamination is removed Applying cleaner to the cloth rather than spraying it directly on the screen will minimize the amount of overspray that may collect at the bottom of the screen e Application Use One characteristic of the resistive touchscreen technology is that it averages multiple touches So If you touch the screen with two fingers at the same time on opposite sides of the display the reported location to the application will be in the middle of the screen Consider this in navigation of your application Touchscreen and Peripheral Drivers Drivers for different operating systems have been supplied on a CDROM that accompanied your MCI Touch Monitor If you cannot find the disk or need additional copies of the software contact Preh at techsupport prehusa com Americas only or support preh keytec de Drivers for the MCI 15T MSR and Line Display modules might not be included in your installation CD Please download latest drivers from our support area
14. eyhole Slots The three large keyhole slots may be used to secure bolts inserted from the front side with nuts threaded on from the back side of the mounting surface Insert bolts in mounting holes loosely thread nuts on from back side slip stand keyholes over bolt heads and position bolt shaft in the narrow portion of keyhole slot Tighten nuts from back side to finish the installation e Top down Anchors To attach the stand to the mounting surface from the front use the two round holes adjacent to the cable access cutout and the hole in the center of the smaller keyhole slot near the front of the base plate The back holes are accessible through the stand when the rear cover is removed and the front hole is accessed through the small cover in the top surface of the plastic base To remove the cover rotate it 1 4 turn clockwise by inserting a flat blade screwdriver in the cover slot To attach the display to an arm or other mount use the VESA compatible holes after dismounting the display mounting chassis from its stand The VESA holes are designed to allow for easy attachment of the display to standard swing arms and mounts Display Setup and On Screen Display Connect and secure cables to the display and the computer except for the USB cable The AC cord set provided with your display should be appropriate for your region If the proper cord set has not been provided you may use any cord set with an IEC320 connector at the applian
15. ft Right Up Down Horizontal Size Fine OSD Tool OSD Left Right OSD Up Down OSD Timeout Factory Reset OSD Language Color Adjustment Audio Adjustment Volume Mute ON OFF Auto Dim Auto DIM Dimming Range Controls the display contrast Controls the display brightness Automatically sets display image size position and fine adjustment Contrast and brightness are not adjusted Controls horizontal position Controls vertical position Increases or decreases the horizontal size of the image Controls the vertical fine adjustment May improve picture detail in emulation modes Adjusts the default horizontal position of the OSD on the display Adjusts the default vertical position of the OSD on the display Determines time in seconds that OSD waits before closing automatically after no action has been performed Recalls original factory settings of image parameters Selects the OSD menu language English French German Italian Spanish Japanese Traditional Chinese or Simplified Chinese Adjusts preset color temperature of the image Available choices are 9300 7500 6500 and 5500 Kelvin K A User mode allows custom setup of each color component of the image Red Green and Blue Default setup for this parameter is 6500 K Do not adjust color temperature unless you have a specific need to do so Adjusts the loudspeaker volume Mute ON turns off the audio function Mute OFF restores the audio
16. l issue advance replacements with 24 hours US Only after an Preh Keytec Return Material Authorization RMA number has been issued for Product to be returned Warranty repairs shall be warranted for the remainder of the original warranty period for the Product This warranty is void if the Products have been repaired altered or modified in any manner by persons other than Preh Keytec without Preh Keytec s prior written approval This warranty excludes prototypes and conditions in Products resulting from normal wear and tear Defects caused in whole or in part by failure to properly store install operate or maintain Products in accordance with good industry practices and Preh Keytec s recommendations are excluded from warranty coverage Damage caused by use of the Product other than that which it is intended is excluded from warranty coverage Repair or replacement is Customer s exclusive remedy under this warranty except if such remedy is adjudicated inadequate Preh Keytec shall refund the paid price of the Products Preh Keytec will pay to return the Products to Customer The turnaround time on repairs will usually be thirty 80 working days or less Preh Keytec accepts no added liability for additional days required for repair This warranty shall not be enlarged or modified and no obligation or liability of Preh Keytec shall be created by Preh Keytec offering technical advice assistance or services relating to the Products Before returni
17. lay electronics is assigned to and displayed by a specific location on the display panel a pixel At resolutions other than native see emulation there is not a one to one correspondence between the video information elements and the available pixels on the display The display electronics must compensate for this and cannot do a perfect conversion thus emulation modes never look as good as images displayed at the native resolution Nit The standard unit of luminance is the candela per square meter cd m2 or Nit Pixel Abbreviation for picture element In an electronic display the smallest complete element of the picture that contains all possible colors and proper brightness In your Preh MCI Touch Monitor one pixel of the LCD panel is a square window with an area of about 0 3 x 0 3mm containing three smaller windows that pass red green or blue light at the appropriate brightness in response to the video signal from the computer Polarizer A thin glass or plastic sheet that filters out light rays of all but a specific orientation Light passing through such a sheet is thus polarized POS Acronym for Point Of Sale Serial A data transmission method where each bit a 1 or O of data is passed sequentially or serially over a single data path a wire The most common standard for this method is called RS232 This is a very common method of interfacing peripheral equipment to older computers Today this metho
18. ng Products to Preh Keytec on warranty claim Customer shall remove from the Products any hardware data software or programs or keep backups Preh Keytec disclaims any liability for loss of such data in returned Products PREH KEYTEC MAKES NO OTHER WARRANTY OF ANY KIND WITH RESPECT TO THE PRODUCTS except as specified herein ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF Erel KeyTec
19. nt light range of 0 150 Lux as measured by the automatic light sensor If the ambient light is brighter than 150 no dimming will occur until the light level drops below 150 and then will drop proportionally to the measured light level e A Dimming Range setting of 100 means that the image brightness will be reduced to its minimum in total darkness conditions e A Dimming Range setting of 0 means that the image brightness will not be reduced at all under total darkness conditions Touchscreen and Touchscreen Drivers Touchscreen Features and Use Your Preh MCI Touch series touch display is equipped with a resistive touchscreen Features of a resistive touchscreen that are important for your use are e Composition The touchscreen is made of a thin about 1 8 sheet of glass overlaid with a layer of plastic The resulting composite is placed in front of the LCD panel in your Preh MCI Touch Monitor e Activation The touchscreen can be activated by anything that applies a force of about 1 ounce over a normal fingertip sized area Objects with smaller contact areas such as a credit card pen pencil tip or pencil eraser will activate the touchscreen with even less force So in normal circumstances a very light touch is all that is required to navigate your application with the touchscreen e Use and Abuse The touchscreen plastic layer has a hard front surface coating on it and will withstand years of use with fingers fingernails and oth
20. on may be required Contact Preh Technical Support at techsupport preh com if assistance is required 3 Press the ENTER button on the OSD controls A pop up window on the display should appear with the message Auto Adjusting Please Wait 4 Inspect the top bottom left and right edges of a typical application to make sure you can see the entire image on the display without scrolling If so you are finished with the basic setup of the display Display Resolution If your application requires use of the display at another resolution than 1024 x 768 such as 800 x 600 you may achieve satisfactory operation by using the Auto Adjust procedure described above or you may need to use the individual controls in the OSD to properly adjust the display Access the OSD main menu and use the Video Adjustment functions see table on next page to resize move or adjust the quality of the displayed image OSD Menu and Function The complete OSD Menu is shown in the table below The Main Menu icon for each menu group is shaded and the individual functions within the group follow To access the OSD Menu push the MENU button Use the ENTER button to select a highlighted menu and to move between individual items within a menu Use the UP DOWN buttons to select deselect an item or to increase decrease the value of an item 7 Contrast amp Brightness i gt ah F a niill Contrast Brightness Video Adjustment Auto Adjust Le
21. red from an outlet strip or remote master switch or when the monitor is installed in a kiosk or other location where the power button is inaccessible OSD buttons UP DOWN and ENTER will scroll through available choices when held down continuously The Auto Sensing Brightness Adjustment feature is intended to be used in situations where the ambient lighting can change significantly over time The brightness of the image tracks ambient brightness and dims the display as the ambient light decreases making the image less obtrusive under reduced lighting conditions where high image brightness is not necessary for good viewability To use Auto Sensing Brightness Adjustment 1 Turn AutoDIM OFF with the Auto DIM OSD menu 2 Set Brightness to desired value in brightest expected ambient light 3 Turn AutoDIM ON 4 Set the Dimming Range to desired value See discussion below 5 Close AutoDIM menu If the brightest ambient light is 150 or above as reported by the Auto DIM OSD menu units are approximately in Lux a common measure of illuminance or lighting of surfaces by light sources the brightness will not change when the Auto Dim feature is turned ON However when the ambient lighting is less than 150 the display will immediately dim in response to the setting of the Auto Dim range and the ambient light e Dimming Range is a measure of how much the display will dim when ambient light is reduced e Dimming only occurs in the ambie
22. t amp MCI 15T C1TR4 Beige Additional features Power indicator for display built in to power switch Touchscreen Technology 5 wire resistive Digital on screen display OSD Hidden software lockable Active Screen Dimensions Horizontal 11 9 304mm Direct access to brightness audio mute and video auto adjust Vertical 8 9 228mm Auto Sensing Brightness Adjustment Monitor Dimensions With Stand Height 13 89 35 28 cm Rubber Wedge Sealed touchscreen Width 15 75 40 cm Removable base Depth 10 89 27 66 cm Two 75mm VESA mounts On base and display chassis Without Stand Height 12 32 31 30 cm Top or bottom access to countertop mounting holes Width 15 75 40 cm Kensington lock connection on chassis Depth 2 68 6 80 cm Broad range of vertical tilt 5 to 90 Weight Actual 15 b 6 8 kg Two built in 1W baffled speakers Shipping 21 b 9 5 kg Two Port USB Hub MCI 15M amp MCI 15MD models only Brightness MCI 15T C2RT2 LCD 250 nit Product Agency Approvals UL cUL TUV GS FCC Class B With Touch 200 nit Warranty 3 years 24 hour advance replacement In the US MCI15TC1RT4 amp LCD 400 nit MCI 15T C2RT4 With Touch 320 nit Resolution Native 1024 x 768 at 60 70 or 75 Hz Supported 800 x 600 at 60 72 and 75 Hz 720 x 400 at 70 Hz 640 x 480 at 60 72 and 75 Hz 640 x 400 at 70 Hz Viewing Angle Horizontal 140 Total 70 left right Vertical 125 Total 60 up 65down Contrast Ratio 500 to 1 Scanning Frequency Horizon
23. tal 31 5 60 kHz Vertical 60 75 Hz Video Input Analog RGB VGA Analog RGB with sync on green Video Bandwidth 78 75 MHz Input Video Format VGA SVGA XGA analog Power Supply Voltages DC 12V Power Dissipation Temperature Humidity External Connections Connectivity POS Options Additional features Product Agency Warranty MCI 15T C2RT2 MCI 15T C1RT4 amp MCI 15T C2RT4 Operating Storage Operating Storage Power Audio Video Touch Interface MCI 15T C2RT4 MCI 15T C1RT4 Magstripe Reader Customer Display 21 W max 40 W max 0 C to 40 C 30 C to 60 C 20 to 80 non condensing 5 to 90 non condensing External 12VDC power pack 5 5mm miniature jack Standard 3mm Stereo Jack HD15 VGA Dual Interface USB Serial Controller DB9F 9 pin connector serial interface Standard USB series B receptable detachable USB cable 2 x Standard USB series A receptacle detachable USB cable 3 Track Reader with Power and Error Indicator Light Only MCI 15T C2RT4 and MCI 15T C1RT4 2 x 20 VFD Display with Dual Axis tilt amp swivel Movement Only MCI 15T C2RT4 and MCI 15T C1RT4 Power switch state memory Digital on screen display OSD Rubber Wedge Sealed touchscreen Hidden software lockable controls Direct access to brightness audio mute and video auto adjust functions bypass OSD Auto Sensing Brightness Adjustment Removable base 75mm VESA mounts on
24. the Kelvin K Contrast Ratio The ratio of the luminance of the display of a full white image to a full black image This parameter is useful in determining the relative sharpness of two displays a higher contrast ratio usually implies a sharper image especially when text is displayed Controller or Touchscreen controller The electronics that actually process the touch on the touchscreen and sends out a digital representation of that touch to the host computer Emulation As used in display technology emulation mode means an image displayed at a non native resolution For your Preh MCI Touch Monitor and other 15 monitors the common emulation modes are 800 x 600 and 640 x 480 In emulation modes a monitor cannot perfectly display the image sent from the computer when the monitor pixel to image pixel ratio is not an integral multiple Hub or USB hub An electronic circuit that combines several USB signals into one illuminance The measure of how much luminous flux per unit area that impinges on a particular surface or how bright a point source of light appears to the eye It is measured in footcandles or in lux Kelvin The scale of temperature measurement that begins at absolute zero The increment of temperature that one Kelvin represents is the same as that of the Celsius scale but the scale starts at 273 16 C Thus 293 K is about 20 C or 68 F Keyboard emulation Produces the same output as a keyboard or a keyboard wedg
25. uto Sensing Brightness Adjustment for the best performance in changing light conditions e High resolution resistive touchscreen with Dual Interface Serial and USB connections e 0 001024 x 768 native resolution e On Screen Display OSD for display setup with vandal resistant lockable controls e One click access to Brightness Audio Mute and Video Auto Adjust functions e Universal internal DC power supply allows world wide operation without user configuration e State sensing lockable power switch prevents display from being turned off by vandals and restores operation after AC power is interrupted e Power on indicator built in to power ON OFF switch e Variety of VESA compatible mounting options e Top or bottom access stand lockdown for stable counter top mounting e Kensington lock connection on touchmonitor chassis for best public access security e Cable management access through display base and bottom e Touchscreen has high performance wedge seal for best contamination rejection in harsh environments e Two high performance baffled loudspeakers with 1W 1W audio amplifiers and electronic volume controls e Optional MSR and customer display for the ultimate POS package Connections and Installation Data Connection Begin your installation by selecting a data connection For most models you may use either a serial or USB data connection MCI 15M and MCI 15MD models use USB only Choose the appropriate data cable from
Download Pdf Manuals
Related Search