Home

PR1713 Installation Manual

1. Menu item Hint Parameter see previous page Serial Ports Configuration serial interface Builtin 51001 RS485 Slotl 5232 5100 RS485 Slot3 RS 232 Protocol select for each port selection only for not yet used protocols X ON standard setup amp for oper device LEWCOM Vl V2 V3 communication only possible at one interface in PR1713 RTS CTS hardware handshake only for completely connected R S232 interfaces RemoteDsp device only once in PR1713 WeM Print X device only once in PR1713 Modem supports Modem signals selection only for RS232 on PR1713 04 None possible selection for VDU terminal Baudrate data rate 300 600 1200 2400 4800 9600 19k2 Bits data transfer 7 8 Parity data transfer None Odd Even Stopbits data transfer 1 2 Slaveadr A Y enter only with protocol ASYCOM Vx Device terminal mode Raw l O VT52 Ansi Echo Disabled Enabled Software Parameter configuration of some basic parameters language operating Language English Local Language Key timeout operating console 1 3 sec Low battery Check On Off 1 min Lines Recipe 1 255 enter Recipe simulation on off Report to communic amp proloc communication proloc none Tare key Enabled Disabled Set zero key Enabled Disabled Allow quit on off Reset on stoptquit 1 sec 5 sec disabled 588 01 Inter
2. Fr 2 2 e Sel 7 Analogteil He ae ep werent Typenschild auf der R ckseite des Ger tes 96 rel 1 10 PR 1713 In order to facilitate weights amp measures approval by the local authorities labels and seals which can be fitted on the indicators shown in the example above are enclosed in a plastic bag in the cover of this manual We recommend using a fibre tipped pen with water and ultraviolet light resistant ink g type Staedtler PANCOLOR EAM 4007817 32116 for the inscription on the labels If necessary this pen is available under service code no 5312 310 18045 from your local G W T sales or service organization 6 2 Digital part Processor MC68331 with 16 MHz SRAM 2x 128k8 max 2x 512k8 in SMD Optional PR1713 05 2x 512k8 for plugging into DIP FLASH 2x 512k8 EEPROM 2k8 SPI 6 2 1 Display Green vacuum fluorescent display with serially connected data interface Weight display top 7 large digits for weight dimension and status Dialogue display below 2 rows each with 20 characters dot matrix for text 6 2 2 Keyboard For the entry the front panel is provided with a foil covered alphanumeric keyboard with 31 keys Dimensions 103 x 247 mm 6 2 3 External keyboard External PC AT keyboard max 50 mA current consumption no additional units are possible The standard socket for the keyboard is protected by a multi fuse element 6 2 4 Built in RS 232 interface
3. 30 Subsequent zero correction eeeeeeeeee 76 PRIT740 47 48 Subsequent zero correction without weights 79 59 Survey 48 physical interfaces 59 PRI79 48 59 Switch on messages 54 Print Setup ata r eee 48 System console eseis 47 53 Printer Device niei nem eds 47 System printer cene edicere 47 production survey eeeeeccceeeeeeeesnceceeneeeeeeneeeeeteneeeens 7 T dnce Ie DEED TOS 7 47 Programming tool cceccceeeescccceceeeeeeeeeseneeeeeeeeeeeees 7 tare command abore Peu 69 PROLOG x BI REN ER ied 54 92 Tare key plene ERR 46 Protocol acte eter teet ete 58 APIS aere ur ADU 46 Terin l eea eee eE S R S 53 106 rel 1 10 PR 1713 Test BCD Output eee 91 W POSS DIOS 2l Wee EAE TAE AAEE 59 69 Test Fieldbuscard esee 91 Ti 45 MAT EN E eet OE 36 37 RICO AEAEE EEEE as T rect Mother eee 54 63 TEE SUCUT cabins redo der Dre tent dope 55 edd i TTY 59 weighing points 00 0 eee 81 BS PE ERTS AS SEG weight U WIN Terminal eere 53 Units connected to the remote bus 25 Z Updat
4. Fe 5E Ra Rao Ran Thereby Ra is the load cell output resistance The following formula is applicable to the mean output resistance RaAvr 1 RaAvr Ra n The formula is simplified if load cell sensitivity C and output resistance Ra are almost equal for all load cells caw C Span Calculation of equivalent input voltage in mV V 78 rel 1 10 PR 1713 The span indicates the equivalent input voltage in mV V related to the full scale It is calculated as follows full scale load cell sensitivity C mV V span mV V pan load cell capacity sum of all load cells e Deadload calculation of the equivalent input voltage in mV V The input voltage equivalent to the deadload in mV V is calculated as follows deadload weight load cell sensitivity C mV V full scale deadload mV V Unless the deadload is known from the very beginning it must be estimated and this estimation must be used to calculate the deadload in mV V The subsequent zero correction can be used to redetermine the deadload subsequently hopper is empty See Subsequent zero correction in Weighing point calibration with weights 5 6 7 1 Calibration without weights Proceed as described in points 1 to 7 of the Weighing point calibration procedure This is followed by the actual calibration 1 The following command line is displayed in the calibration mask Deadload Calibratio
5. dg e Regn 96 6 3 ENVIRONMENTAL EFFECTS 5 d oO OO e d OD eR TORTE EPA Ue RERO REFUGE etd ae eda hoes 97 6 3 1 Power voltage sagss5 bie eure d ed dea e ees 97 6 3 2 Environmental conditions eese eene 97 6 3 3 Electromagnetic immuhlily i42 ete 97 6 3 4 RF interference 97 6 3Y CE conformity marking 5 utter tte ete atte ed ede cobs Hr aet e eet ede 97 6 4 MECHANICAL DATA SCION UNIES RR Eidem ere 98 6 4 I Construction type RU ER E REDE E E Re ete Iren tro E PU ya e e rt eet e egeret 98 O42 Dimensions EE EE AQ 98 6 4 3 98 6 4 4 ACCESSOTIOS RET E E 98 6 4 5 Welglli s cet tto er data dtp ete eade d ent Unde eate E E E east an T 98 6 5 OPTIONS Addon to d SOHO OP dO EE COR IR Oe wei ten ed 99 OD ANGIOR OULD UE i Ss ies de d e acc osse Ite ee No sat e D Een Ie siete in see c ee 99 vi rel 1 10 PR 1713 0 3 2 Digital In PUS iR TIR e RT e ORIENTE TERT NRI RERO it 99 6 5 3 Digital outputs ioi eee E ee eed a dg oh See feet E ete ei ee ee Hone deeds 99 6 5 4 SerialAnterfaCes o Ense ett e ete dne re ete et e e e ale doa sat So e e e RE ect Hense oe diee hon 99 6 6 FIRED BUSES ieese
6. e Display of the previous next selection with the keys N or P Previous Next Select input field by means of cursor keys 7 and J Changing parameters change parameter Selection is from 2 or more possible values Undo changes PR 1713 rel 1 10 57 5 2 Configuration Calling up mask Configuration is from the Main Command Level by pressing key C Fi td PR1713 00 Rel XX XX XXXX XX XX Configuration IMIG SOR sooox 1380682116 Set date Set time Change serial I O parameter Add delete show license Set software configuration Set fieldbus configuration Set units Print all configuration data Exit If a production in PR1713 is active configuration is disabled Production is active no configuration possible Hit any key to continue Press any key to remove this message from the display Function survey Set date D Set date Set time T Set time Change serial interface parameters C Change serial I O parameter Add delete and display licences L Add delete show license Change and display software configuration S Set software configuration Parameter of fieldbusoption PR1721 0x F Set fieldbus configuration Entry of user defined units U Set units Print out all configuration data P Print all configuration data Calling up the required function is by actuating the relevant key Leave menu Configuration E Exit Ret
7. eU PU ERR E TREE EUH AERE ERE TRUE Aa RG ERU HRS 47 d 5 0 Licence Setp e d deett eder ge tee ea t nte eine tete ee da 48 4 5 7 Print SC CUP Qua REESE EM 48 4 3 8 Refresh Display ain d e EN DE te e Sete Idee ete ESSE tte a ee ae ee 48 4 3 9 SliOW Versions sues atate E ieget ec Hv deer eripe 46 chen cases debs die dates 48 4 6 CONFIG PROGRAM SET UP MENU Je a iere e E YER E EATER ETE ERR e LETTERE e Eee e e E 49 4 6 1 Production report parameter S oiana neret nene 49 4 6 2 Layout of printed reports 49 4 0 3 Batch pardmeterscas eet he ag eie on e rte dana 49 26 4 EU D RO REGERE ERRARE dE ER EET Ee qo des go 50 40 5 Printer INLET ACO sis e e d vere idee ete e ehe et etu e ga ege det eee eT tede eroe 51 4 6 6 Digital T O Coding eei dee eee reet ete ee Logo gebe a ge Peste doe be eese tope tad eden ente 52 4 7 ENTER FIX TARE WEIGHTS etu A states 52 4 8 COUNT FACTORS eee E E enierirte siste en Re E erae 52 5 COMMISSIONING WITH TERMINAL ecce eee eerte ee eee ette tn aseo esset sette ease eese eee a assess esee eee eo assess eee eee 53 5 1 SYSTEM CONSOLE CONNECTING MENU STRUCTURE eene hene nnn n nnns nnns nsns nsns nsns nsns sss s nsns sese se senes ns
8. 17 Q41 Ws bl 18 Q42 Ws vio BI blue 19 Q44 Ws gr 20 Q48 Br sw Vio violet Gr gray 1 Q51 Br rt 2 Q52 Br or Ws white 3 Q54 Br ge 4 Q58 Br gn 5 Enab Br bl 6 Uext Br vio 7 Br gr 8 Br ws Voltage supply for the output transistors 6 Uext ground potential 7 GND Earth cabinet 8 Attention avoid earth loops to GND Q51 SIGN sign bit If PR1713 08 is used as BCD output for weight values the Q52 STSTI standstill bit output bits of the 5th decade can be used as follows Q54 ERROR error bit 058 DAHOL data valid Output Each output line of the module PR1713 08 works with common external voltage supply as reference potential and an open Emitter output A passive output has a high impedance An active output supplies a voltage which is e g 1 7 V lower than the supply voltage The load is between the output and GND A module with open collector output can be built on request the load then is between the output and the supply voltage e supply voltage external voltage Uext 5 V 24 V max 32 V e voltage drop 1 4 V at 50 mA in the switching transistor 0 3 V in protection diode Output cycle coupled to measuring time or per program may be controlled external e output lines 24 Emitter of switching transistor Load connected to GND max 50 mA output size 3 Byte depending from application program example Binary BCD output 7 0 1 1 1 0 1 1 1 Q08 Q04 Q02 Q01 Q08 Q04 Q02 Q01 hi
9. Reset all to default YES Naso PO left softkey yes right softkey no Example In the main menu press the More key until you read Setup above a softkey see also operating manual During editing the More key must be used also for selecting the weight unit g kg t Ib Example set FullScale n key 3000 kg if necessary change f s d with numeric keys and More key All parameters can be selected in the lower line If a rhombus is displayed left and right of a line the other list items can be displayed using the scroll keys to scroll up and to scroll down Only the items which can be configured in the instrument after the adjustments are displayed 34 rel 1 10 PR 1713 Dependent of function the input modes are switched over between selection from a menu a selection box or entry of alphanumeric characters editing The relevant value is displayed beside the parameter i e a quick survey of all configuration settings is possible by parameter scrolling For editing e g parameter Baudrate it must be selected with key In this case the value for the parameter is chosen by selecting The parameters can be left either by 1 key or Quit key In field save after changes answer request for saving Save Slot 3 RS232 vgs changed value is saved Example p YES NO No nochange back to menu item above 4 3 Main menu After connection
10. System Weighing Controller PR 1713 Installation Manual Installation manual 9499 053 45710 Edition 3 Dat 20000808 for PR1713 Release 1 10 BIA LA INCED by GLOBAL WEIGHING GLOBAL Weighin eee sartorius group GWT GLOBAL Weighing Technologies GmbH P O B 730 370 22123 Hamburg Germany Tel 49 40 67960 303 Fax 49 40 67960 383 Please note Any information in this document is subject to change without notice and does not represent a commitment on the part of GWT This product should be operated only by trained and qualified personnel In correspondence concerning this product the type name and release number as well as all license numbers in relation to the product have to be quoted Important This product is partly copyrighted It may not be modified or copied and may not be used without purchasing or written authority from the copyright owner GWT By using this product you agree to be bound by the terms stated herein Bitte beachten Alle Angaben in diesem Dokument sind unverbindlich fiir GWT und stehen unter Anderungsvorbehalt Die Bedienung des Produktes darf nur von geschultem fach und sachkundigem Personal durchgef hrt werden Bei Schriftwechsel ber dieses Produkt bitte Typ Bezeichnung und Versionsnummer sowie alle mit dem Produkt in Zusammenhang stehenden Lizenznummern angeben Wichtig Dieses Produkt ist in Teilen urheberrechtlich gesch tzt Es darf nicht ver ndert oder kopiert und ohne Er
11. 1 signal on A B O signal off gt B TxA TxB RxA RxB GND TxA TxB RxB GND PR1713 00 slave 1 PR1713 00 slave n 18 rel 1 10 PR 1713 3 3 5 PR1713 06 analog output card PR1713 can work with only 1 analog output power consumption The galvanically isolated connections of the analog plug in card offer 1 signal output analog 16 bits 0 4 20 mA The analog output is configured for gross weight No set up in configuration mode is necessary After coldstart the card is detected and the output is configured to 0 4 20 mA gross weight Pin allocation of options connectors in the PR1713 00 unit Installation see page 10 Address analog card The BI 1 345 678 QWn 0 address n 1 OPT1 depends 29000000 n 2 OPT2 from OPT n 3 OPT3 socket Write data as see 3 2 1 All 2345678 oooooQoooQQ 0 gt OmA 20000 gt 20 mA Terminal row free B1 B2 B3 B4 B5 B6 B7 B8 rear upper row one one ne one once Tc once ne Terminal row A analog Ai A2 A A4 A5 A6 A7 AB front bottom row output nc nc nc nc nc nc out GND ext analog Out Analog signal ie s n 0 20 mA current output The current is A2 supplied directly from the terminals analog Out 1 a 0 20 mA 4 20 mA A2 Analog signal 0 10 voltage signal The voltage level corresponds to the voltage drop at the 500 Ohm resistor 500 Ohm 10 ppm K PR 1
12. 52 rel 1 10 PR 1713 4 6 6 Digital I O Coding The digital outputs Components and the digital inputs recipe numbers can be addressed directly or binary up to 255 over 2 cards comp amp recipe 1 0 single digital in and outputs are addressed directly Comp amp recipe I O 4 TE binary digital in and outputs are addressed binary 4 7 Enter fix tare weights After selecting softkey Fixtar from the main menu Fixtare no name 19 0 00 kg is displayed 9 Fixtare memory can be opened for entry of a fixed tare value and their name This menu can be used for taring the weight display with a fixtare value editing the fixtare value and loading the actual gross weight into the fixtare memory Several fixtare values can be selected After selecting a number an other menu is displayed Fixtare no name Edit enter tare weight and name Tare tare WP A Tare Edit Weight Weight gross tare enter name Print single or all 4 8 Count factors After selecting softkey Count from the main menu Count no name 1 87 pcs 9 memory locations can be prepared for fixed count factors and their name to realize a counting scale With the count factor the weight can be converted to a number The value is displayed below the name in the lower display line Several count factors can be selected After selecting a number an other menu is displayed Count no na
13. Batt Y 3 4 1 Activating the battery The unit is delivered with the battery not connected The battery must be connected follow the safety hints The jumper for the battery is located on printed circuit board 2 beside the connector with the 4 pole power supply cable The jumper must provide the connection between the posts to activate the battery After the battery was activated the clock data and time needs adjustment 3 4 2 PR1713 05 RAM extension If higher RAM storage capacity is required e g for Alibi Memory PR1713 81 two optional DIL Ram s of 512k8 capacity can be fitted The 2 empty sockets for the memory extension are located on print 2 beside the connector with the 4 pole power supply cable When inserting take care to orient the components correctly The marking in the housing and the marking in the socket must be located on the same side 28 rel 1 10 PR 1713 3 4 3 PR 1721 field bus interface The Fieldbus interface PR 1721 is an option for installation in PR1713 00 or PR 1713 01 Communication protocols and syntax comply with the relevant bus standard The communication with the Fieldbus interface is described in the book 9499 050 44210 Fieldbus card PR1721 xx Software interface manual PR 1721 supports these protocols PR 1721 01 Profibus DP slave interface PR 1721 02 Interbus slave interface PR 1721 03 CANbus slave interface on request PR 1721 04 Device Net slave interface 3 4 4 Installation of the fi
14. Complete by pressing the enter key PR1713 checks the entry for plausibility If the entered full scale is smaller than the calibration weight specified during calibration Calipoint or if the calculated input voltage for the specified full scale is out of the permissible limits the new full scale value is rejected The full scale is rejected if less than 0 8 counts d are provided e Ifthe entry is accepted the following message is displayed during approx 1 sec Status OK e Possible error messages Bad Weight e g dimension missing Status Arithmetik overflow e g weight value too high Status Above phymax calculated input voltage 36 mV Too many d resolution too low 0 8 c d Status Below Cal value below calibration point Illegal Fullscale the last two digits are unequal to 00 or have more than 3 digits behind the decimal point Leave input item without changing the old measurement value with operator error e f necessary delete entries position the cursor in the leftmost position with the cursor key lt Delete all entries with the delete key Del e Enter key 1 The old span remains unchanged Adjusting the stepwidth divisions Stepwidth 5 6 4 Default span Use the default span value Return to FiXed or X to set fixed span Press key X for taking over the default span To avoid operator errors the displayed prompt must be replied with YES NO Y N 5 6 5 Weighing point calibration pr
15. Configuration Date Time Serial I O Licences Enter Delete Print Software configuration Fieldbus configuration Entry of user defined units Print Weighing point Display Calibration Additional weighing points Service Show hardware configuration Memory Test modules PR1713 04 PR1713 06 PR1713 12 PR1713 13 Show last error Print all configuration data Proloc The following sections and subsections are structured accordingly 56 rel 1 10 PR 1713 5 1 4 General operating notes All the terms used in the masks are in English In the description the relevant English expression or display text is shown in a different font A submask can be left on several ways which are displayed in the lower mask area e g Exit save and leave Q Quit leave immediately Using the automatic repeat function of the keyboard can cause a crash of the terminal emulation program Remedial action in case of trouble 1 Close the terminal emulation program under Windows 2 Open terminal emulation program under Windows 3 Interrupt the PR1713 power supply shortly 5 1 4 1 Editing functions in masks In the lower mask area of some masks the possible editing functions are displayed Previus Next change parameter Undo changes for Editing functions
16. PR1713 00 Rel XX XX XXXX XX XX License Configuration IMIG SOX sox sex 0951 g5 Boardnumber 9131135 A Add a License PR1713 20 Enabled Complex batching controller PR1713 21 Disabled Multi recipe management D Delete a License PR1740 11 Disabled Production control and supervision PR1740 21 Disabled Production plan P Print License PR1740 31 Disabled DDE transfer PR1740 41 Disabled PR1740 Remote control The board number is displayed below the header The licence numbers to be entered must refer to this board number Otherwise they are not accepted by the system The status of all licences is displayed enabled or disabled Editing function Add a License D Delete a License Print License E Exit After pressing the relevant key A or D the system prompts for entry of a licence number Enter License number _ The system checks the licence number Unless it is accepted by the system message Not a License number or Wrong License number is displayed If the licence number is unknown delete the wrong licence number with the backspace key lt and terminate the entry with 1 PR 1713 rel 1 10 61 5 2 5 Entry of software parameters Calling up mask Set software configuration is from sub menu Configuration by pressing key S PRIVIS 00 Eel Software Configuration IMIG
17. Programming the card Slot number n 1 3 for OPT1 3 e Writing to output QBn 0 lower byte3 0 18 14 Q12 Q11 004 Qo2 aoi QBn 1 middle byte3 1 Q38 4 Q32 1 G28 Q24 Q22 Qai QBn 2 upper byte3 2 Q58 Q54 Q52 51 Q48 Q44 Q42 Q41 If the addressing is made as WORD or DoubleWord the highest byte Q6 Q7 is invalid output bytes Q7 Qe Q5x Q4x Q3x Q2x Qix Qox Writing bytes x x 2 1 0 Writing WORD 1 0 Writing DoubleWord 0 e Reading inputs lBn 0_ byte3 0 o o 1 1 1 J108 J107 J106 DEEXT reserved for detecting of the output type of card DEEXT is the transferred Enab signal defined by J103 J104 table setting With open J105 Enab can be used for any purpose 24 rel 1 10 PR 1713 3 3 9 PR1713 13 DIOS master Only 1 card PR1713 13 can be used in PR1713 The DIOS card digital I O system as a simple Interbus S master is the connecting module for external I O extension The maximum possible number of ports is limited to 256 bits or 16 modules at the remote bus Only one Interbus S master in the system is possible Interbus S is intended for process data input and output The card has galvanically isolated connections and integrated termination resistors No jumper 5 9 is fitted master The DIOS master offers e abus interface
18. Sox xoox soxex 9331251 Language English Frontkey timeout 2sec Low battery Lines per recip 30 Enable recipe simulation on Report to communication Frontkey tare untare enabled set zero enabled Allow quit in mainlevel on Reset on stop quit disabled 588 01 Interface off 5 2 5 1 List of parameters and possible entries Language Frontkey timeout Off 1 sec 2 sec 3 sec Low battery on off 1 min Lines per recipe Enable recipe simulation on off Report to Frontkey Allow quit in mainlevel Reset on stop quit 588 01 Interface Language for operator dialog Selecting the dialogue language for the operator not for configuration English default or Local Language Default alternative language German Gross and tare display holding time Holding time of PR1713 function keys Battery monitoring display Alarm message with The alarm message is output continuously with on not output with off and with 7 min the alarm message is output once per minute during some seconds The alarm message is output on the left display Lo bAt Lines Recipe Maximum number of lines for recipes 1 255 Recipe simulation Set recipe simulation on off For starting recipes with modified batching modules recipe simulation can be switched off Report to Specify destination for batching reports select with scroll keys for none all PR1740 and Proloc local printer communication PR1740 Proloc l
19. names in the order of allocation found in the slots The first card is detected as TTY1 and TTY2 whereby TTY1 is the RS 485 and TTY2 is the RS 232 interface If 2 or All 2345 67 8 3 PR1713 04 cards are fitted logic names above TTY2 do also exist starting with OPT1 see 3 2 1 Terminal strip RS 232 B1 B2 B3 B4 B5 B6 B7 B8 rear top row DCD RXD DIR Sign RTS CTS RI _GND _ Terminal row A RS485 422 A1 A2 A4 A A6 A7 A8 front bottom row Switch ON Sign TxB TxA HRxB RxA nc nc nc acc to table GND PR 1713 rel 1 10 15 Connection to the RS 232 interface all protocols Supervisory system PLC printer PR1628 00 24 remote indicator Rx Tx GND 9 pol sub D B 6 7 Tx Rx GND RTS CTS Tx Rx GND RTS CTS PR1713 00 PR1713 00 With hardware handshake connect cables with the handshake partner according to RTS CTS Connection to the RS 422 485 interface point to point Printer PR1628 00 24 remote display PR 1604 Rx RxB TxA TxB GND 9 pol sub D TxA TxB RxA RxB GND TxA TxB RxA RxB GND PR1713 00 PR1713 00 16 rel 1 10 PR 1713 Connection of a Modem to the RS 232 interface asynchronous protocol Modem DCD RxD TxD DTR GND DSR RTS CTS HI course of events Transmitter side 1713 induced switch on DTR 1713 induced switch on RTS Modem confirmed switch on CTS 1713 induced send TxD Receiver side Modem confirmed DCD is ok 1713 ex
20. ze nm lI gl 9 ve 5 4 DOF Data our mo CUR ui NN S baB CUM MI E II rc 0 2l Die ID LI tal DO2 W_Data out Pin 5 pol Dir hu porn AME ______ ND 1 LS oc cl LI 15 DO1 A Data out V 3 4 4 1 PR1721 01 Profibus DP interface Profibus PR17xx N PR17xx Slave PR1721 01 VP B A DOND B D 4 Le PR17xx S Use screened twisted bus cable 1x2 Bus termination at both ends by resistors at the bus 220 Ohm and for power supply 390 Ohm each GSD file GWT 00C3 GSD for PR 1721 01 can be copied under our Internet address our website in Internet http www global weighing com 30 rel 1 10 PR 1713 3 4 4 2 PR1721 02 Interbus S interface 8pol 5pol PR1721 PR1721 PR1721 1 002 1 001 InterBus S InterBus S InterBus S 2 DI2 2 DI den Slave Slave Slave 3 GND 3 GND TEN 5pol 8pol a 5pol 8pol 5 002 4 1001 6 DI2 5 4 CC 8 Con_Test e Interbus S connection Please take care for potential equalisation between PR 1720 and the device which is prior to it in the bus Use screened twisted bus cable 3x2 The bus signal is looped through each module Both the input and output side must be connected The bus arrives at no 15 55 and continues with 18 8 A gland is provided for each cable A link 43 8 in th
21. 4 5 Battery replacement This unit contain a lithium battery for memory back up saving the data When exceeding the specified minimum battery voltage or in case of defect the battery must be replaced by the GWT customer service or by an equivalent trained person and disposed of in accordance with the local regulations After delivery the battery is not connected Battery connection is via a jumper see 3 4 1 Activating the battery There are different possibilities for monitoring the battery voltage during operation For function and adjustment of the LoBat indication see 4 5 3 3 Low Battery Check 1 4 6 Disposal Electronics scrap is special waste Please follow the instructions of your local disposal company 1 5 Cleaning If necessary the front panel can be cleaned using a damp soft cloth Use only little water or isopropyl alcohol for moisturizing With the PC AT keyboard connected protection type IP 65 is not met any more No moisture must enter the instrument inside PR 1713 rel 1 10 5 2 SYSTEM WEIGHING CONTROLLER PR1713 PR1713 is equipped with an internal weighing point display and keyboard for simple applications The instrument is programmable according to the IEC 1131 3 standard for field of application see data sheet With PR1750 PR1713 can be matched easily to the application operation recipe functions process steps process control by built in PLC With an application program the uni
22. 8 3 3 3 1 Remote display For connection of a remote display one of the serial RS 232 interfaces is available The remote display PR1627 can operate with the instrument 14 rel 1 10 PR 1713 3 3 4 PR1713 04 Serial I O The plug in card contains 1x RS 232 and 1x RS 485 422 whereby only the RS 485 is galvanically isolated Max 3 cards PR1713 04 can be used in PR1713 The parameters of the serial RS 232 interface are adjusted by software configuration The RS 485 RS 422 interface for serial communication must be configured by DIL switches on the interface card before installation The table indicates which switches has to be closed ON for a certain mode Protocols are configurable by software set up ON DIP switch S101 H li Adjustments for RS 485 422 12 3 4 5 S101 1 ON Tristate enable ON RS 485 OFF RS 422 2 ON Rx disabled while transmitting OFF Rx continuously enabled 3 ON Bus pull up resistor Rx38 1k54 at V 4 ON termin Bus terminator Rx2 205E at diff bus 5 ON ation pull down resistor Rx1 1k54 at V PR1713 04 Two wire system Four wire system point to point bus point to point bus Master RS 485 RS 485 RS 422 RS 422 1 2 3 4 5 1 2 3 4 5 4 3 4 5 Slave RS 485 RS 422 1 2 4 other slaves RS 485 485 1 2 1 default last slave RS 485 RS 485 1 2 1 3 4 5 The interfaces are given logic B
23. A E TE A E AEE EAEE T 34 Installations atti de Ned feel d te eed 1 3 2 Electrostatically sensitive components enon eese esee eene aa aie enne ener 1 3 3 Opening the instrument ue Re eletti te eto tain 1 3 4 Eartheniftig Aedes St adu unn BN EN E n NE S T 3 9 ProltectiVeserthi d eire etel dodi ode vestem ede vedi Ce sobs RSEN ER EL 1 3 6 Power connection PR1713 00 cccccccccccccccsssssscccccccccccccuussecccccssecussseecccssssuuusseecccsssseuseeececssssuuuseeesccsseseuusseeeceess 1 4 REPAIR AND MAINTENANCE cccsssssscccccccecsssssesseecccceeeeaueseeeccceeeeauasseeecceeesauusssecccceeeaauanseeccceeesauanseeceseesauanseeceeensaees 1 4 1 Failure and excessive STVESS cccccccsecscccccccccccccccccsssssssecccesccccsscussssssssesceseccccsscuussusssesecceesccscssuuussseecesssssuuseseesceees T4 2 Forspecial attention ede o e PO REN tad RR HE Ete TE tees JN SA E I M M M EN LAA Soldering Worki RERUM Ee ie tbe lop tue tel sled idee ole ERE RA e eben EE tel ales DAD Battery replacemerit se eee er n te ie eed e as eos DBO DISPOSAL eie etin ue e a dad Cia TIENE SR CREER 1 5 bt teen m Uii nocd E fia cane uu A Ion ro NR 2 SYSTEM WEIGHING CONTROLLER PR1713 eee eeees ee eee ee eee enano eese states ases esee etae tasa sese esee eee eoa sees eee 24 BASIC INSTRUMENT S
24. Aether Aa 44 PR 1750 00 ton ahve ene st 7 Set dat etie tie e UR ettet eese 57 PR IZ780 0 andina de iade 7 Set Deadload deed 41 PR 1781 0025 e ter Ttt hn rer ties y Set FullSC le verde Ene i RD 40 PR 1790 0 ice te eee te 7 Set 5 Ihi eiu hii RESI 41 tenet ete tee eee teen 7 Set Stepwidth essen 40 PR1627 ieiunio RP 13 59 Set tme i d eO DER C RE Ee Pee end 58 59 SEU ZETO KEY i und e ee 46 PR1713 Problemreport eene 108 Setup menu esee S HER NIS 35 PR1713 00 Commissioning ee 31 Show e tete een dte tees 48 PR1713 04 serial I O module testing 88 Simulation 5 2 detienen ebbe 46 PRYZISPT2 siepe etr tpe teet EE 20 software parameters cesses 61 PRI713 15 inii blan 21 70 edes 44 SPM a eint acest E eee tiet E tut oe ated es 44 PRIJ21 47 Standstill 68 1721 protocol 5 4 ee eee eet 47 Step by step 74 PR1721 01 Profibus DP interface 29 stepwidth etse iere ete 40 69 83 PR1721 02 Interbus S 30 Stop Quit mee eerte tested 46 PR1721 04 Device Net Interface
25. Byte 16 01 new input data 1 00 Byte 16 00 output has not been transferred 01 Byte 16 01 output has been transferred 80 Byte 16 80 no output because bus error PLC should test this byte 9elB n 3 Diagnosis bit Register IX n 24 Ready Bus Module is O K and running 9eIX n 25 Fail Bus Module has failure 1 n 26 Run Interbus S is in normal active state n 4 Module Count IBn 5 internal parameter With QXn m 0 the slave is addressed QXn m 0 Use 1 3 for OPT1 3 m 0 3 for slave 0 3 Bit in module e g 0 7 or 0 31 depending from module Module number m 0 3 for Slave 0 3 M Slot number 1 3 for OPT1 3 Note PR1750 Rel 1 60 SP1 or newer required for DIOS Interbus S ST Modules are supported Limitation for Interbus S master with 8 bit modules The Interbus S master PR1713 13 is not able to hand modules with odd multiples of 8 bit size The modules must have a size of 16 24 32 bits 32 and 64 bit modules must be aligned to multiples of 32 bit Means the consecutive number of modules with a width of 16 must be even if they are placed between 32 or 64 bit modules 26 rel 1 10 PR 1713 3 3 10 PR1713 14 Ethernet Ethernet in preparation With SW release 1 12 Ethernet is supported The card is plugged in slot 4 the connector for fieldbus cards installation see page 28 PR 1713 rel 1 10 27 3 4 On main print 2 PRI721 0x
26. PR 1 713 rel 1 10 85 5 8 Sub menu Service Mask Service is called up from the Main Command Level by pressing key S H sm El td PR1713 00 ROK Service Show hardware configuration Show available memory Test Inputs Outputs Show last fault Print all configuration data Exit IMIG OX SOK Roo 099315531 The following menu items are called up by pressing the relevant keys Display of hardware configuration Display of available memory Test of input and output modules Hex Dump of the last fatal system error H Show hardware configuration M Show available memory T Test Inputs Outputs F Show last fault gt If a production in PR1713 is busy the module test T is disabled Production is active testmode is not possible Hit any key to continue Press any key to remove this message Print out all configuration data Leave sub menu Service P Print all configuration data E Exit As no data can be changed return is direct to the main menu without additional prompts 86 rel 1 10 PR 1713 5 8 1 Available memory in PR1713 Calling up mask Show available memory is from sub menu Service by pressing key M 123648 17312 106336 1 106336 1196 262144 0 lel s SOK 4 BORK SOK KOK FOES SOK Service MEMORY STATISTICS bytes maximum memory available bytes memory in use bytes free memor
27. PR 1713 21 Batching function with several recipes x 255 components each freely configurable PR 1713 30 Standard batching phases InBatch 256 l Os PR 1713 81 SW Alibi Memory W amp M PR 1740 11 Recipe management and component management PR 1740 21 Production plan PR 1740 31 DDE interface e g for InTouch PR 1740 41 Remote operation via a terminal PR 1750 00 Programming tool on CD OEM PR 1750 10 Programming tool instrument PR 1781 13 Phase configurator PR 1791 13 DDE server For details on the programs see the relevant program manual Additionally are needed e g PR1713 12 in option slot 1 und 2 PR1713 04 in option slot 3 2 2 2 Plug in cards and modules optional On the connecting board PR1713 can accommodate up to 3 identical or different plug in cards Product PR1713 04 max 3 cards 2 serial interfaces RS 232 and RS 485 RS 422 The RS 485 serial interface must be configured before installation via DIL switches on the interface card Protocols configurable by software set up PR1713 06 1 Analog output galvanically isolated only 1 card Configuration and fine adjustment of output levels with software correction Signal output analog 16 bits 65000 divisions 0 4 20 mA PR1713 07 1 Analog output 4 analog input only 1 card Output see PR1713 06 Input 4 channels with common ground resolution 3000 d PR1713 08 BCD output 5 decades
28. Rel 1 02 upwards the input signal of the digital interface is a logical 0 with open input lines Accessories options external supply required Digital input The signal lead must supply sufficient current see technical data With 24 V at the terminals the max current flow can be 8 mA and 4 mA with 12 V No logic level is defined for terminal voltages within 10 V and 5 V From 0 5 V the input is open Take care that the polarity is correct and that the limit values are not exceeded A supervisory system can read the status of these inputs Digital output Each output of PR1713 12 is switched via an NPN transistor Relays should have interference suppression or a protective diode connected in parallel with the coil in blocking direction with direct current The permissible output rating is for PR1713 12 max switching voltage 32V max switching current 25 mA Voltage drop at 25 mA 3 V typical Each output of PR1713 15 see next page is switched via a relay contact Pin allocation of options connectors in the PR1713 00 unit Addresses sockets see 3 2 Installation see page 10 T OPTI OPT Terminal row B Digital input B1 A rear upper row B2 K Li 96IX1 0 IX2 0 IX3 0 B3 A B4 K IX1 1 IX2 1 96IX3 1 B5 A B6 K IX1 2 96IX2 2 9 2 B7 A B8 K IX1 3 IX2 3 9 3 for PR1713 12 transistor and for PR1713 15 relais Terminal row A Digital output A1 C 3x QX1 0 QX2
29. Terminal block functions calibration configuration operation communication Mode RS 232 XON XOFF ANSI various protocols Baudrate 300 19200 Bd Data bits 718 Bit Parity none odd even 6 2 5 Power supply PR1713 00 Power voltage 115 V 230 V AC 10 15 48 62 Hz Power consumption 14 5 W 19 VA PR 1713 rel 1 10 97 6 3 Environmental effects 6 3 1 Power voltage sags Power voltage sags gt 10 ms at 100 sag without instrument reaction gt 20 at 50 6 3 2 Environmental conditions Temperature range Ambient temperature operation 10 40 C Switch on temperature 0 40 C Storage transport 40 70 C Humidity lt 95 without condensation acc to IEC 68 2 Protection type IP65 Vibration to IEC 68 2 6 test Fc 6 3 3 Electromagnetic immunity Electrostatic discharge min IEC1000 4 2 level 3 Interference supply and data cables min IEC1000 4 4 level 2 Electromagnetic fields min IEC1000 4 3 level 2 6 3 4 RF interference suppression Electromagnetic emission acc to EN55011 group 1 limit value class B 6 3 5 CE conformity marking PR 1713 00 is CE approved according to EMVG with the following text The product PR1713 00 for non automatic weighing systems complies with the following European guidelines Number 89 336 EEC as amended by 91 263 EEC 92 31 EEC and 93 68 EEC Text Council guideline for harmonizing the legal regulations of the member states on e
30. always be carried out 5 4 3 Saving the weighing point parameters temporarily When interrupting the configuration calibration the new data which were entered can be saved The relevant weighing point may already work with these parameters Nevertheless they are not saved in EAROM so far With power failure these temporarily saved weighing point parameters are lost With power recovery the weighing point parameters saved in EAROM are used automatically Saving the weighing point parameters temporarily is done from mask Calibration only possible with switch CAL open e Terminate calibration Exit calibration enter letter E From the reactions offered by the system select e Dont save Enter letter N for using data temporarily 5 5 Weighing point configuration The editing functions for parameter entry are described in the first sub section the individual parameters are described in the following sub sections e For entry modification of weighing point parameters switch CAL must be open 5 5 1 Editing functions for parameter entry e Weighing point selection Weighing point selection is before calling up this weighing point calibration mask by means of the two cursor keys T and J The actually selected weighing point is highlighted by inverse display e Command lines The weighing point calibration mask is displayed with different command line dependent of the CAL switch position e Command line weighing point parameters p
31. at for Output Value IMIG x SOX zooo s 09231551 Hex BFF Display of the socket number is in mask header Test PR1713 06 Slot Number 2 Enter the analog output value Entry of the analog output value is possible in various formats Selection is by entry of the relevant letter e decimal entry 0 100 e hexadecimal entry The dialog line for decimal input is displayed as an example decimal hexadecimal Leave mask Test PR1713 06 with E Exit D Decimal Input Format 0 100 for Output Value Hexadecimal Input Format for Output Value Dec 075 Hex BFF After leaving this mask E return is to the sub menu Test Inputs Outputs The entered output values remain set until returning to menu Service Display of the actual analog output value is in the two formats See line Current Analog Output Value With PR1713 07 additionally the analog inputs are displayed similar to Analog Input 1 3072 Analog Input 4 3072 75 3 75V Hex 75 3 75V Hex BFF BFF 90 rel 1 10 PR 1713 5 8 3 3 Digital module testing The test can be executed for PR1713 12 and PR1713 15 Rel 36 HOR KAX XX Test PR1713 12 Slot Number 3 Mo 09 31 51 Inputs I1l 1 I22 0 I3 1 4 1 Outputs Dec 1 Hex OB Bin 1011 Enter Bit Number for Reset 11 Set Outputs Decimal Input
32. contact voltage 32 V 32 V Max contact current 25 mA 1 Voltage drop at 25 mA 3 V typical 6 5 4 Serial interfaces Up to 3 optional interface modules PR1713 04 Mode RS 232 and RS 485 on the interface module Baudrate 300 19200 Bd Data bits 7 8 bits Parity none even uneven 0 or 1 Protocols EW bus remote indicator printer XON RTS 100 rel 1 10 PR 1713 6 6 Field buses 6 6 1 Interbus S Profibus DP DeviceNet Baudrates kBps Common Services INTERBUS Standard DIN 19258 INTERBUS Baudrates kBps 500 kBps Knode width 8 bytes or 4 words Process data yes Parameter data no ID 03 remote digital bus unit with I O PROFIBUS Standard EN 50 179 volume 2 PROFIBUS DIN 19245 PROFIBUS Process Field Bus part 1 and 3 Baudrates kBps 9 6 19 2 93 75 187 5 500 1500 automatic detection Buffer size 8 bytes I O data 8 bytes per UserPrm No Sync YES Freeze YES Clear YES Set Slave Add No DeviceNet Standard Specification DeviceNet Volume 1 Release 1 3 and Volume 2 Release 1 2 from 4 3 1996 125 250 500 Get_Attribute_Single Set_Attribute_Single Reset PR 1713 rel 1 10 101 6 6 2 GSD file for PR1721 Profibus DP Use our website at Internet address http www global weighing com for loading the GSD file GWT_00C3 GSD for PR 1721 or generate file GWT_00C3 GSD by entry of the following listing the comments behind the semi colon are optional
33. dE T eed e E E e Dea re a ode en 18 3 5 0 PR 173 07 Analog e aee En OO EUH 19 3 3 7 Control I O PR1713 12 Opto PRI713 15 Relay Output eese eene nennen enne nnne 20 3 9 0 PRITIS 08 BGDQUIDUE ee t ee Ri Rue epu 22 3 3 0 PREZTS IS DIOS MASET E o Med IER sed ice DR pS 24 3 910 PRITISZIT Ethernel diet beh TE ede odis 26 JA OONAMAIN PRINT 25 5 EE eedem 27 3 4 1 ACHVALNG the batery 27 3412 PRIZIS 05 RAM extensions de bead st es wok acs Cason teed Baer ae tee eds tee M Pt t Neh PEON RNAS 27 34 3 PRA 2T field Dus interfaces iia casi atte Si tess sie nai Sie 28 3 4 4 Installation of the fieldbus 28 4PR1713 00 COMMISSIONING ceo e e eo eo oen 31 4 1 DATA SAVING POWER FAILURE ccccccccssssesecccccecceusccusssseccceeeeausseeeccceeseaausseeccceeecaueeseeccceeesauasssecccesssauaaseecceeessaaaness 31 ASTD Calibratiomd alasc su b trei tn UE Ras 3 4 2 CONFI SUTTON data ease pede as venereal 32 4 1 3 Programming With PRIZJSQ s ti d dt ed o eb d Ped 32 dob d COld mets cu 32 iv rel 1 10 PR 1713 4 2 DISPLAY ELEMENTS AND CONTROLS ON THE BUILT IN CONSOLE s sssseeeeeeeeeeeeeeeeessseeseesesessssseessssesssssessseeeseseeeeees 32 4 2 1 Control signals 3 5 peu E qd ee qe La pg e
34. data weighingpoint parameter Menu item Hint Parameter Setup i For all set up in PR1713 inclusive calibration and licences Calibration Calibration call up all analog part specific data New Modify Parameter for WP operating New Modify Here the calibration data of the scale are specified Set Fullscale 0 000100 9999900 kg t Ib g dimension with More enter value Set Stepwidth 1 2 5 10 20 50 select with More Set Deadload Load mV V Enter Deadload 0 000000 mV V enter value only Set Span Load mV V Enter current load 0 0001 9999900 kg t Ib g dimension with More enter value ___ Enter Span 1 000000 mV V enter value only Calculate test calculate testfigure Exit calibration Save noSave Undo Parameter Here the parameters of the scale are specified Analog filter on off Digital filter _ Off bessel aperiod 10 012 5 00 Hz enter value only ultirage mode off on Multirange limit 1 0 9999999 d crossover from small to middle stepwidth Multirange limit 2 9999999 d crossover from middle to large stepwidth Test mode A Absolute Relative W amp M Disabled Enabled Measuretime 0 05 2 00 s enter value onlyn Standstill time 1M 8M enter value only Z
35. entry the values are shifted from right to left Point or comma are part of the mask cannot be entered During entry the content of the item is underlined The entry can always be canceled by pressing the space key The old value remains unchanged The parameter entry is completed with key Enter Subsequently the entry is checked If an entry is within the permitted range the value is stored and not underlined any more If an entry is not within the permitted range the entered value is replaced by the next permitted value and remains underlined The operator has the following possibilities Press key Enter to confirm this next value Enter a new value Redisplay the old value by pressing the space bar 5 5 2 Filter Analog Filter Select between Filter 2 Hz or no filter Digital Filter Select between Bessel filter aperiodic filter or no filter With digital filter enter the cutoff frequency Fcut 0 1 5 00 Hz The measuring time is fixed to 50 ms e After changing of the filter parameters the maximum accuracy should be reestablished by re calibration 5 5 3 Analog test mode Testmode Determination if the test measurement displays the deviation related to FullScale absolute or to 0 relative is made Calibration with without weights is completed with a test measurement and the result is scaled so that FullScale is displayed This value is displayed when pressing the function key Test 68 rel 1 10
36. for max 256 additional dig 1 0 e automatic detection of connected modules e connection of PR 1720 as 2 weighing point Pin allocation of options connectors in the PR1713 00 unit installation see page 10 Terminal row B free B1 B2 B3 B4 B5 B6 B7 B8 rear upper row _ hc one one ne Anc one re Terminal row A Interbus S A1 A2 A3 A4 A5 A6 A7 A8 front bottom row DO DI GND nc nc DO DI nc PR1713 13 in PR1713 PR1721 02 in PR1720 f fed an amp 841 pond gt 900ga jp Norm An ae CA Busklemme nterbus S remote bus PR 1713 rel 1 10 25 3 3 9 4 Units connected to the remote bus PR 1713 13 4 remote bus devices gt H H 3 i DIOS DB 9 Slave 0 DB 9 Slave 1 DB 9 Slave 2 DB 9 Slave 3 Modules with 1 8 byte can be handled Please note the limitation to 256 I O resp 32 bytes For e g PR1720 8 bytes are required i e 192 I O are still available in this case A bus terminal with local bus is also a slave Via jumper 5 9 at the output of a slave module the master is informed that further modules in the bus will follow With pre fabricated Interbus cables twisted pair jumper 5 9 is integrated in the cable connector When withdrawing the connector the master is informed automatically that the bus has become shorter Interbus S actuation IB n 0 00 Byte 16 00 no new input data 80 Byte 16 80 no input because bus error PLC should test this byte 01
37. in one step is possible e f only a relatively small calibration weight e g 10 of the full scale can be placed on the scale step by step calibration is required The calibration weight should be a high as possible otherwise the error is too high 5 6 6 1 Calibration in one step with weights Proceed as described in points 1 to 7 of the Weighing point calibration procedure This is followed by the actual calibration 1 Command line zero Unload in the calibration mask Calibration by weight Unload and hit O or S to skip Q to quit E to end X to set fixed span P to print The system offers the following replies Unload and hit 0 unload the scale and set the zero S to skip skip zero setting Q to quit leave the calibration without doing anything E to end calibrate and finish X to set fixed span set the fixed span P to Print print out the weight value 2 Setthe zero Unload the scale press key 0 e PR1713 evaluates the data The command line of the weighing point calibration mask is Setting deadloads the system stores the data This is followed by Setting deadloads Status OK message is displayed during approx 2 seconds e The following weight value is displayed 0000 kg Repeat zero setting in case of error See section 3 and 5 PR 1713 rel 1 10 73 3 The following command line is displayed in the mask Unload Load Calibration by weight Unload and hit O or S to skip E to end X t
38. interface PR1721 xx In operating mode Scale Interface Enabled a standard interface with 8 byte between scale and fieldbus is established In operating mode Scale Interface Disabled an IEC 1131 application program in PR1713 is needed to support the fieldbus interface 4 5 4 1 PR1721 protocol PR1721 protocol displayed only if the PR1721 module is inserted in the unit None Interbus S for 02 Profibus DP for 01 DeviceNet for 04 Dependent of selection other parameters are required e g With Interbus S value n 1 50 indicates the actualization interval 1Bs cycle 25 ms Calculate the value by 66 7 number of bytes 0 3 x number of slaves 10 Enter address for Profibus DP Profibus DP address 1 126 1 For DeviceNet enter two parameters DeviceNet baudrate Baudrate selectable to 500k 250k 125k 500k The MAC ID identifies the device DeviceNet MAC ID Enter address 1 60 1 After parameter entry PR1713 makes a warm start in order to initialize the PR1721 module in the unit 4 5 5 Show Boardnumber Boardnumber 123456789 board number is displayed Show Boardnumber This number is required to order a licence 48 rel 1 10 PR 1713 4 5 6 Licence Setup Licences for stand alone operation PR1713 20 PR1713 21 Licences for operation at InBatch PR1713 30 PR1781 13
39. interval 0 Zerotrk ti gt 0 Switch off interval 0 Zerotrk ti 0 5 5 9 Zero tracking range Zerotrk rn Permissible range 0 00d to 500 00d 5 5 10 Zero tracking stepwidth Zerotrk st Permissible range 0 00d to 10 00d e For W amp M applications the correction must not be above 0 5 d sek e The automatic zero tracking stepwidth should be smaller than the standstill range also with non W amp M applications PR 1713 rel 1 10 69 5 5 11 Zero tracking interval Zerotrk ti Entry is in measuring times permissible range 0 off to 100 e Switching off the automatic zero tracking is by setting Zerotrk ti 0 5 5 12 Multirange scale The multirange function is controlled by three parameters in the calibration With Multirange mode on the scale has three ranges with different resolution the change over limits Multirange limit 1 and Multirange limit 2 represents the range border If the gross weight has more d as the relevant change over limit the next wider stepwidth is used 1 gt 2 gt 5 gt 10 gt 20 gt 50 If the gross weight is lt 0 25 d of the lowest range the scale in standstill and untared condition the scale will be switched back to the lowest range During Calibration the multirange function is principally switched off 5 5 13 Tare time out Tare timot Unless the tare command can be executed within time number of measuring times e g because the scale was not in standstill condition the wei
40. n uidi ated Bie deine 10 Control VO Opto esee 20 21 D Data Savin 8s nime eir i t Er ice tan 31 DDE interface unn neon 7 DDE Server xerit ptm eir pA 7 D adload ounzebice pre a 70 Default spati 25 ase cede eI ep ANO PS 71 Devicetyp linee ehe So eher 58 p ntes eR nU 20 21 Digital Inputs uitae HR RR res 99 Digit l interface ra eme ERE 7 digital module ine reg 90 Digital module testing esee 90 Digital output 5 etant Deren 20 21 DIOS vise RRA es 7 24 E Editing functions in Masks 56 EN61010 HERE 1 2 Error me 8g68 5 ior teo te eger Te etait 42 80 Error messages on the weight display 42 7 23 Exit calibration eese 42 External Rene piter evt er EARS EE 44 F eee tee eere ene xe eR 67 fir Wate ee ER 38 El sh iii de BE RP se Sg 36 38 El shlt 32 ies ie et edt 38 full scale value ees 71 FEullScale iet ete te ce ee et tese 770 83 Function key debe diede 61 reete n ree E Ure PERSE PUE EE PEU ees 3 10 EX880 nO 59 G glands Ra iones 11 Gravimetric weight 82 H housing istoc bn t ende tereti 8 I IEC TOTO tede pie C 1 Tai Bate inan fous bath a steaks ds des Sev
41. off B 2 0n B 2 off printer device batchrep auto prt comp amp recipe I O 4 6 1 Production report parameters The batchreport of the last batch contains headlines date recipe production data and a line for each component see PR1713 operating manual The two headline texts in the reports can be edited freely company name address The report functions were realized as IEC 1131 module they are available on CD i e the reports can be matched by the user by means of the PR1750 programming system Report text 1 20 characters of freely definable text which appears in the batch text report first text e g company name Report text 2 20 characters of freely definable text which appears in the batch no text report Second text e g company address 4 6 2 Layout of printed reports With the printkey on the frontpanel the weight can be printed in a predefined format to a connected printer The adaption of the printing mask can be managed with print layout The standard report starts with an empty line it follows date and time D G a line of 40 dashes the grossweight 40 dashes and new line You may select D Date and time Datum xxxx yy new line G Grossweight Brutto 1234 kg new line N Netweight Netto 1234 kg line T Tareweight Tara 1234 kg new line Line of 40 dashes new line 1 the contents of report text 1 n
42. saved by command Moreover the calibration parameters can be protected by switch CAL Before calibration the unit should be allowed to warm up 1 At each power on the calibration data are loaded from the EAROM into the working pod tancum emen LOO A A E ues temcssecencnecsesccentescouaseeunubrescucntesenausesenturesenanees ITI TEE petet PFPE PERC ees te roc Ee rg oett iri PORE EEFEEEEEETEEEEEEEEEETEEEECEEEETEEEEEEEEEEEEEE SETTE IEEE CET CUC EC EHE TEETH EIE EEEEEERE EC EHERTEECUEEEETEEEEEEEEECEEETETEEEEEEETS arum toma EE HE eset mer Frost E ENA E 5 iFunction Saving calibration loads the modified calibration data into the EAROM 32 rel 1 10 PR 1713 4 1 2 Configuration data Adjusting the serial interface communication field bus parameters The configuration settings are also saved by command The configuration settings are independent of switch CAL i e access to the configuration settings is always possible 6 With the EAROM deleted the pre set configuration data are loaded into the working 10 i At each power on the modified configuration data are loaded into the working memory 4 1 3 Programming with PR1750 Programming with PR1750 is only possible with the CAL switch open Project files tag pco can be loaded on line directly
43. steps are Step 0 tare Step 1 calibrate with maximum possible calibration weight e Calibrate with the maximum possible calibration weight e 2 Print out the calibration data This calibration must be done particularly carefully because any error will repeat itself will be added with all following steps Step 2 Calibrate with 1 substitute weight calibration weight 2 calibration weight e Replace calibration weight by substitute weight Load the scale with a substitute weight instead of the calibration weight If e g a weight hopper is concerned water must be filled in until the substitute weight corresponds exactly to the calibration weight To reach this value as exactly as possible the weight with the higher internal resolution 2 additional digits is displayed above the large weight value in the weighing point calibration mask Print out the calibration data Note The weighing point was already calibrated but for a smaller range Step 3 Calibrate with 2 substitute weight calibration weight 3 calibration weight e Replace calibration weight by substitute weight e Print out calibration data Step n calibrate with n 1 substitute weight calibration weight n calibration weight e Replace the calibration weight by substitute weight e Print out calibration data The max number of steps is determined by n calibration weight lt full scale Step 0 and step 1 correspond to C
44. the holes of the plug The optional plug in cards are provided with pin markings and port addresses list for each slot as well as connecting examples as far as necessary The terminals are described A1 A2 A8 and B1 B2 B8 Terminal row A is located at the edge of the circuit board near the PG11 cable gland x Option slot OPT3 and terminal B in use Terminal row B is above terminal row A Avoid confusion of plugs for A B PR 1713 rel 1 10 11 The main print 2 PRI721 0x Batt Battery Installation location for PR1721 xx RAM The expression for the PR1721 xx socket is I O Slot 4 3 2 2 Cable gland and connection All cables are fed into the instrument via glands to ensure protection according to IP65 Cable diameters of 6 12 mm for PG13 5 5 10 mm for PG11 and 4 8 mm for PG9 are suitable The conductors are connected to screw terminals in the instrument Max conductor cross section 2 5 mm The strip connectors are mounted on the housing bottom above the holes for the EMC glands The power connecting terminals excepted all connecting terminal units are of the plug in type The conductors taken to the terminals shall be as short as possible The conductors of each cable must be tied together with a cable strap shortly before the terminal block All cable screenings must be connected in the metal sleeves of the PG gland Don t take the screenings into the unit 1711_ 54 WPG Mou
45. to the PR1713 by EW Com Firmware hex can be loaded off line with menu item Flashrt 4 3 2 1 Flashlt 32 also can merge project files 4 1 4 Cold start With the Stop key kept pressed during switch on at power recovery the boot menu is displayed The user can select e cold start program and database are deleted interface configuration and calibration data remain unchanged e a warm start all data remain unchanged In another menu item the unit factory setting can be reestablished Thereby calibration data interface configuration and hardware clock are set to standard values See also operating manual The boot menu can be called up also from the configuration menu 4 2 Display elements and controls on the built in console PR 1718 oes Textdisplay with EE 20 characters The W amp M weighing 6 OHOOOOOD umm oem per line GHI JKL MNO point display cannot be used by programs alphanumeric dialogue keys as well as editing keys and function keys can be used by a program Weighing point keys Stop key Quit key Softkey Scroll key More key Enter key PR 1713 rel 1 10 33 4 2 1 Control signals Functions zero setting tare untare weight display mode selection and print key are allocated to the front panel keys i e these functions are accessible to the operator The functions of F1 F3 has to be programmed on demand 4 2
46. to the power supply the unit the console on the front panel and the built in interface cards the terminal if provided are initialized see 4 1 Text PR1713 Rel xx xx with the PR1713 version number is built up on the alphanumeric display The unit can be configured on the front panel console or after switching over on a terminal The operation of the unit is menu guided Calibration and configuration are accessible via menu Setup from the main menu In the main menu the PR1713 version number and a 1713 Rel 01 10 choice of application programs are displayed Eaten FixTar Count with More key the next functions are displayed Setup Display of main menu depends from the loaded applications e g Batch Count Dependent of licence or programming further or other application programs can be selected with More key Without loaded applications only Setup is displayed Call up the configuration level with Setup Overview on the menu items in the main menu Menu item Hint Parameter Fixtar Application Part of the standard application see operating manual Count Application Part of the standard application see operating manual Atest Display ofthe testvalue for the analogue part which was calculated during calibration Setup Forall Setup parameters in PR1713 inclusive calibration and licences Prod Application Part of the standard application see op
47. valid after a min warm up time of 60 minutes reference temperature 23 C Values specified without tolerances are average values and are only used for information 6 1 Analog part A D conversion Principle DC voltage integrating A D converter ratiometric to the load cell supply voltage Conversion time 50 ms down to 10 ms in preparation Measuring time 50 ms 100 ms and multiples up to 2 s Analog filter active Butterworth low pass 40 dB decade limiting frequency 2 Hz Digital filter active 4 order Bessel filter or aperiod limiting frequency adjustable within 0 1 Hz and 5 Hz 6 1 1 Accuracy and stability Accuracy class 10 5000 d according to OIML R76 EEC approval D99 09 039 Min meas signal W amp M 0 5 mV V or 6 mV for 5000 d 0 3 mV V or gt 3 6 mV for 3000 d Linearity error 0 007 Zero stability error TKo 0 1 uV K RTI SPAN stability error TKgpn lt 6 ppm K 6 1 2 Sensitivity Sensitivity at 11 2 cnt d 1 2 uV d for 5000d W amp M OIML R76 1 0 yV d for 3000d W amp M multi range scale at 4 cnt d 0 42 uV d not for W amp M at 1 cnt d 0 11 uV d not for W amp M internal sensitivity Resolution internal 2330000 steps with 36 mV Min meas Signal 20 03 mV V for 3000 steps internal not for W amp M Input voltage meas signal deadload 0 max 36 mV Deadload range 36 mV max meas signal entry calibration via software 6 1 3 Load cells Load cell connection all strain gauge cells 6 or 4 w
48. yes disabled no 4 5 3 8 Set zero key Set zero key Zero setting from the front panel is possible front panel console Enabled Enabled yes disabled no 4 5 3 9 Allow quit Allow quit The main configuration menu can be left with Q at the terminal the interface is free of f Q is effective 4 5 3 10 Stop Quit Reset on stoptquit After pressing keys Stop and Quit simultaneous for duration of n sec 1sec during operation the boot menu is displayed n 1sec 5sec disabled Reset switched off PR 1713 rel 1 10 47 4 5 3 11 588 01 Interface Unit at PR1740 or stand alone on Standard function module on unit is used with InBatch 588 01 Interface OFE 4 5 3 12 Printer Device at System printer Printer Device at Switches the printer to a serial interface All available interfaces are Builtin RS232 selectable with the scroll key Example slot 1 RS232 requires a printer at the RS 232 interface on slot 1 4 5 3 13 Operator Device at System console Operator Device at Switches the console to a serial interface All available interfaces are Builtin RS232 selectable with the scroll key Example slot 3 RS232 requires a terminal at the RS 232 interface on slot 4 5 4 Fieldbus Parameter Select protocol parameter and operating mode for the optional fieldbus
49. 0 QX3 0 front bottom row A2 E A3 C 96QX1 1 QX2 1 QX3 1 A4 E er A5 C QX1 2 QX2 2 QX3 2 A6 E ys A7 96QX1 3 QX2 3 QX3 3 A8 E PR 1713 rel 1 10 21 3 3 7 1 Control I O PR1713 15 Relay Output Max 3 cards PR1713 12 or PR1713 15 can be used in PR1713 With the standard software the cards are supported in option slot 1 and 2 OPT1 OPT2 The digital interfaces are passive external supply is necessary and have no common potential e 4x outputs dig On Off OUT for process control galvanically isolated PR1713 15 relay output low voltage current not for explosion hazarded areas zone 2 e 4x inputs dig On Off IN for process control The input is galvanically isolated via optocoupler From Firmware Rel 1 02 upwards the input signal of the digital interface is a logical 0 with open input lines Accessories options external supply required Digital input The signal lead must supply sufficient current see technical data With 24 V at the terminals the max current flow can be 8 mA and 4 mA with 12 V No logic level is defined for terminal voltages within 10 V and 5 V From 0 5 V the input is open Take care that the polarity is correct and that the limit values are not exceeded A supervisory system can read the status of these inputs Digital output Each output of PR1713 15 is switched via a relay contact The Contact is configurable by means of solder links and is delivered as closing contact The pe
50. 0 mV V FSD 3000 kg 1 mV V A safety prompt is made Reset all to default YES v W NO YES sets the default values and starts the calibration 4 4 2 2 Set FullScale Modify permits changing of the existing calibration 4 4 2 2 Set FullScale Param changes the measuring parameters 4 4 3 Set Parameters 4 4 2 1 1 10 fold magnifier A 10 fold magnifier function for the weight display can be enabled during calibration with the B gross key toggle 4 4 2 2 Set FullScale Set FullScale 4 3000kg A weight inclusive of can be entered the unit can be changed with More key Press 4 key to set the full scale Display Setting FullScale 3000kg Further keys returns to 4 4 2 7 Exit calibration skips and goes to 4 4 2 3 Set Stepwidth Quit cancels the calibration after safety prompt 4 4 2 3 Set Stepwidth set Stepwidth 1 2 selects the stepwidth the More key changes between stepwidth 1 and stepwidth 10 Further keys u returns to gt 4 4 2 2 Set FullScale skips and goes to gt 4 4 2 4 Set Deadload Quit cancels the calibration after safety prompt za w rA PR 1713 rel 1 10 41 4 4 2 4 Set Deadload Set Deadload 4 W Load V mV V _Discharge the scale and set the deadload with softkey Load in the middle display Setting Deadload Subsequently gt 4 4 2 5
51. 1 4 2 For special attention Make sure that the construction of the instrument is not altered to the detriment of safety In particular leakage paths air gaps of live parts and insulating layers must not be reduced The conductors of each cable must be tied together with a cable strap shortly before the terminal block The manufacturer cannot be held responsible for personnel injury or damage caused by an instrument repaired incorrectly by user or installer 1 4 3 Fuse The load cell supply circuit is protected by a 250 mA slow blowing fuse The following fuse is fitted Wickmann order no 19372K TR 5 Radial slow blowing IEC 127 3 250 mAT The fuse may be replaced only by a qualified person WARNING N Using repaired fuses and short circuiting of the fuse holder are not permitted Note that only fuses of the specified type and current rating in accordance with IEC 127 may be used for replacement The transformer primary winding is protected by means of a thermal fuse After overheating the thermal fuse is molten The PR1713 has to be sent to our service for repair The secondary winding 4 rel 1 10 PR 1713 is protected additionally by a Multifuse 1 85 A If it switches off e g due to low power voltage disconnect the device from power After a cooling down period of about 3 min it can be used again if the power voltage is O K 1 4 4 Soldering work Soldering work is not necessary with this unit 1
52. 2 Language System configuration is exclusively in English For system operation two languages are available The main language is English With the standard version factory setting the alternative language is German Switch over is with the front panel keys via configuration see 4 5 3 1 4 2 2 1 Configuration Calibration Operator dialogue English Operation via console on the front panel or via terminal VT100 compatible or with PC terminal software 4 2 2 2 Operation Operator dialogue in 2 languages English or alternative language Operation via console on the front panel with 31 keys incl num functions or with ext PC AT keyboard and front panel display or via terminal VT100 compatible or with PC terminal software 4 2 3 Operating concept Commissioning PR1713 configuration is on the console front panel or alternatively with a terminal or a terminal program on PC The areas for calibration and configuration can be reached from the main menu via menu Setup Gross weight display for calibration if necessary please untare set zero Operating concept PR1713 is menu guided with softkeys via the front panel keys Inscriptions on the T 3 softkeys below the display are with up to 6 characters per key on the lower display line The symbols in the lower line of the alphanumeric display limits the softkey inscriptions Thereby Y means only these softkeys and means further softkeys with the More key
53. 3 08 is displayed if the card is detected in the system The actual input and output values are displayed binary and for the output also in hex and decimal notation Single output bits may be changed by Set Bit or Reset Bit You may enter output data in hex or decimal format By means of Control X1Y0 the output is controlled by the input Enab 5 8 3 5 Test DIOS Card The screen for testing PR1713 13 is displayed if the card is detected in the system The fields Ready Run must be active Changes of the inputs at the remote bus are displayed By means of Modify bytes outputs at the remote bus can be changed The fields BSA CTR RB LB MOD are not in use they are intended for future extensions Test PR1713 13 Slot Number 3 Diag Bits A0 Ready Fail Run BSA CTR RB LB MOD oo x 000100A001000000 IBS Status 1 x 0000 OB 3 1 x 0000 oo Exit Return Modify bytes 5 8 3 6 Test Fieldbuscard The screen for testing PR1721 is displayed if the card is detected in the system Depending of the type of the card a fitting headline is generated additionally the inut and outputstring is displayed e g for PR1721 04 Test PR1721 PR1721 Devicenet Slave Indata 0000000000000000 Outdata 0000000000000000 E Exit 5 8 4 Printing all configuration data Calling up is done by pressing key P e Print out all configuration data P Print all co
54. 51 C Configuration W Weighingpoint S Service P Prolog Quit Access to the various input masks survey see Table of menu structure below from this main menu Main Command Level is via sub menus Calling up the required sub menus is by pressing the relevant key C W S or P e Configuration C Configuration e Weighing point W Weighingpoint e Service S Service e PROLOC P Proloc e Leaving the main menu Quit If a production is active in PR1713 the configuration is disabled Production is active no configuration possible Hit any key to continue Press any key to remove this message from the display PR 1713 rel 1 10 The entry of can be disabled In this case message Quit disabled is displayed By pressing any key this message is removed from the display Disable the entry Q When using a PC with the Windows terminal program as a system console terminal returning to this main menu is not possible after entry of Q For this a cold start is required i e all entered data are lost When using a real terminal or a terminal program e g Telix returning to this main menu is by means of the BREAK key How and which parameters can be entered in the relevant sub menus input masks is described in the following chapters 5 1 3 1 Menu structure tree structure With configuration on a serially connected terminal the following set up menu is valid Main menu
55. 69 5 5 15 Min weight limit for print out no p below esee eene eene ener rennen neret 69 5 5 16 Stepwidth scale divisions Stepwidth 69 5 5 17 W amp M mode W io Aree ke Pope nta dele PR Rene debet ERR Ree deeds 69 5 6 WEIGHING POINT CALIBRATION 69 5 6 1 Weighing point calibration parameters eese 70 5 6 2 Editing functions for parameter entry eese 70 5 6 3 Adjusting the full scale value Fullscale eese nene nennen enne nnns 71 5 6 4 Default Spams i scit dte t etat idt ie ete idet dt det ite Te dal ates ie dnte 71 5 6 5 Weighing point calibration procedure sequence eee teen nnne nennen nene nnne nennt 71 5 6 6 Weighing point calibration with weights 72 5 6 7 Weighing point calibration without weights eese eene eene 77 5 6 8 Error messages in the calibration menu eese 80 5 7 ADDITIONAL WEIGHING POINTS sutikrina iere epa iei reine rein top Gp ERES 81 5 4E PRIT20assecond WP 5rd t tt et ete efte ta ae e eed 82 5 7 2 Customer specific weighing point eese eee nennen nne nnne heet 82 2 0 SUB MENU SERVICE ir aep ERR NEN UE 85 5 6 1 Available memory in PRI713 cccseccessccsnecessccesscescecessesssecesseecaeessseeceseesseecsse
56. 713 rel 1 10 19 3 3 6 PR 1713 07 Analog I O PR1713 supports only 1 analog output power consumption The card installation see page 10 has 1 output like PR1713 06 and 4 analogue inputs After coldstart no set up in configuration mode is necessary The output is configured to 0 4 20 mA gross weight The analogue input with 4 channels is not supported by the standard software It can only be used in connection with e a PR1713 internal IEC1131 program see Programming manual or e the SW option OBW in preparation On Board Weighing application special manual The analog output is identical with the output of PR1713 06 see preceding page Additionally the terminals A7 A8 are prepared for use in special application OBW The analog input has 4 channels with common ground no galvanic isolation between internal and external electronics Function Technical Data Sampling rate corresponds to PLC cycle for analogue input signals Resolution 3000 divisions in measuring range Over range limiting With an input value outside of the converter range the output is 8FFF Hex for values above and 8000 Hex for values below the measuring range Total Accuracy 0 2 96 Temperature rate influence lt 50 ppm K Analogue input for Input Current 0 20mA Voltage 0 10V DC Voltage 0 5V DC Selection by chan direct input switch nel Setting of switches EJO CH1 ON OFF O
57. FF CH2 ON OFF OFF o EE CH3 ON OFF OFF CH4 ON OFF OFF S201 2502 n m EJO CH1 OFF ON OFF CH2 OFF ON OFF EE CH3 OFF ON OFF CH4 OFF ON OFF 5202 50ka Zu Input impedance 250 Ohm 100 kOhm gt 10 Mo Note set both switches ON for an unused channel Addresses The for analog inputs address IW n k with depends We n 1 3 for OPT1 3 from OPT 1 8 k 0 3 for channel 1 4 socket Read data as WORD see 3 2 1 Terminal row B input B1 B2 B4 B6 B7 B8 rear upper row 4 channels CH1 CH1 CH2 CH2 CH3 CH3 CH4 CH4 Connection of analog output Terminal row A analog A1 A2 A3 A4 A5 A6 7 A8 front bottom row output nc nc nc nc Special special out GND OBW OBW ex applic applic 20 rel 1 10 PR 1713 3 3 7 Control I O PR1713 12 Opto PR1713 15 Relay Output Max 3 cards PR1713 12 or PR1713 15 can be used in PR1713 With the standard software the cards are supported in option slot 1 and 2 OPT1 OPT2 The digital interfaces are passive external supply is necessary and have no common potential 4x outputs dig On Off OUT for process control galvanically isolated PR1713 12 with passive optocoupler outputs open collector max 25 mA e 4x inputs dig On Off IN for process control The input is galvanically isolated via optocoupler From Firmware
58. Format for Output Value Hexadecimal Input Format for Output Value Set Bit Bit Nr 0 1 Reset Bit Bit Nr 0 1 El Exit Display of socket number The socket number is displayed in the mask header Test PRI713_12 Slot Number 3 Display of the actual digital input values 4 The actual values are displayed in line Inputs I 1 R 0 13 114 1 Entry of output values 4 Entry of the output values for the 4 outputs is possible in various formats Selection is by entry of the relevant letter Set all outputs simultaneously e Decimal input format D Decimal Input Format for Output Value e Hexadecimal entry H Hexadecimal Input Format for Output Value Setting resetting individual outputs e Seta bit bit no 0 23 S Set Bit Bit Nr 0 23 e Reseta bit bit no 0 23 Reset Bit Bit Nr 0 23 The dialogue line for resetting a bit is shown as an example Enter Bit Number for Reset 11 Display of the analog output values Display is in three formats See the following mask line Outputs e Decimal Dec 2048 e Hexadecimal Hex 800 e Binary bit 23 left bit extreme right Bin 10000000 00000000 Leave mask Test PR1713 12 with E Exit After leaving this mask E return is to the sub menu Test Inputs Outputs The entered output values remain set until returning to menu Service PR 1713 rel 1 10 91 5 8 3 4 Test BCD Output The screen for testing PR171
59. GSD file for the Profibus interface PR1721 01 Status 12 03 1998 Profibus_DP Vendor_Name GWT Global weighing technologies Model_Name Profibus Interface Revision Version 1 0 Ident Number 0x00C3 Protocol_Ident 0 only DP instrument Station Type 0 compact station FMS supp 0 FMS is not supported Hardware Release 1 0 Software Release 1 0 9 6_supp 1 supported Baudrates 19 2_supp 1 93 75_supp 1 187 5_supp 1 500_supp 1 1 5M supp 1 MaxTsdr 9 6 60 reply times with the different Baudrates MaxTsdr 19 2 60 MaxTsdr 93 75 60 MaxTsdr 187 5 60 MaxTsdr 500 100 MaxTsdr 1 5M 150 Redundancy 0 no redundant transmission Repeater Ctrl Sig 0 no RTS signal 24V Pins 0 no 24V for connection of a maintenance unit Freeze Mode supp 1 Freeze mode is supported Sync Mode supp 1 Sync mode is supported Auto Baud supp 1 Set Slave Add supp 0 User Prm Data Len 0 Min Slave Intervall Modular Station 0 odule 8 Byte Out 8 Byte In OxA7 0x97 EndModule 50 50x100uS gt 5ms min Slave intervall 102 rel 1 10 PR 1713 6 6 3 EDS file for PR1721 DeviceNet EDS file pr1713 eds can be generated by entry of this listing or copied under Internet address http www global weighing com DeviceNet Manager Generated Electronic Data Sheet F
60. IDE TRANSFORMER 5312 253 28005 CABLE ENTRY GLAND PG 9 5312 505 48013 CABLE ENTRY GLAND PG 13 5 5312 505 48014 CABLE ENTRY GLAND PG 12 5312 505 48015 CONNECTOR 7 POL LOADCELL 5312 264 48007 CONNECTOR 5 POL BUILT IN SER I O 5312 264 48008 CONNECTOR 8 POL OPTION SLOTS 5312 264 48009 SCREW FOR FRONTPLATE request GASKIT FOR FRONTPLATE on request 7 2 Other PR1713 documents Operating manual System manual general Batching manual 9499 050 42910 9499 054 43110 Release 1 x in preparation in preparation 9499 057 43210 7 3 Glossary The following terminology is used in this document ADU Analog digital unit converter CAL Single in line switch in the instrument 3 2 for data protection Coldstart All programs and tables loaded in the memory are deleted DDE Microsoft communication protocol EW protocol The serial communication protocol for Global Weighing batching systems version V1 V2 V3 Flash Program loading also parts FSD Full scale deflection GND Ground common earth potential InBatch Batch Control System of the Wonderware company Interbus S A standard communication protocol ISA 588 01 ISA standard related to Batch Control Profibus __ A standard communication protocol Recipe Recipe see ISA S88 SPM Memory area Scratch Pad Memory of PLC Warmstart Ini
61. PR 1713 5 5 4 Measuring time Meastime Measuring time in ms enter 50 or 100 2000 multiples of 100 5 5 5 Standstill detection The PR1713 standstill detection requires the two following parameters to determine the mechanical standstill of the scale During a defined period of time standstill time the weight value of the scale must be within defined limits the standstill range In this case the scale is in standstill condition Standstill range Standst rn Permissible range 0 00d to 10 00d Standstill time Standst ti Entry Number of measuring times permissible range 1 8 5 5 6 Zero set range Zeroset rn Definition of a range around the calibration zero within which e displayed gross weight can be set to zero by pressing the zero setting key or by a corresponding external command or e automatic zero tracking is active Permissible range 0 00d to 500 00d 5 5 7 Automatic zero tracking In case of change of the empty scale hopper weight e g due to loss tare reduction or formation of slag tare increase by only a very low amount automatic zero tracking ensures that the scale is reset to zero automatically Automatic zero tracking is defined with the following parameters With the scale in standstill condition and the gross weight within the zero set range automatic zero tracking is stepwisely step width at defined intervals 5 5 8 Automatic zero correction switch on off Switch on
62. PR1791 13 _Licences for operation with PR1740 PR1740 11 PR1740 21 PR1740 31 PR1740 41 Serup Licence Setup Licence number management entry of licence number Licence Setup Show W Add_WDelete Select the required action with the softkeys e g Licence Show The status for all licences is displayed PR1713 20 Enabled Enabled Disabled Add Licence Enter the number of the licence selected previously Message Wrong Enter number 0 licence No or PR enabled number correct is displayed Delete Licenc Enter the number of the previously selected licence Message Wrong Enter number 0 licence No or PR disabled number correct is displayed 4 5 7 Print Setupdata Setup prints out the initialization data via the in software parameter selected Print Setupdata interface After pressing the enter key the print out is started 4 5 8 Refresh Display Refreshing the weight display intensity The weight display elements which are used very rarely gradually loose their brightness Consequently the luminosity e g within a digit can be different However regeneration of the display intensity is very easy Setup refreshing the display after pressing all display segments are off Refresh Display for refreshing the display intensity wait approx 5 min After the Quit key the display is controlled normally again 4 5 9
63. Save Undo Save stores the calibration display Saving ene Loms Exit Calibration then noSave finishes the calibration without saving display Undo cancels the calibration the following safety prompt Undo calibration is displayed YES V W NO YES cancels the calibration all changed values are lost 4 4 2 8 Calibration error messages ESD MOE multa OF Step F s d value cannot be divided by stepwidth many d for signal Error message at lt 0 3mV V for 3000d W amp M active resolution too high with too low input signal PR1713 tries to reach a valid setting by increasing the default values to FSD 3 mV V and stepwidth 50 FSD below cal weight New f s d smaller than calibrated weight 4 4 2 9 Error messages on the weight display Only analog part error status s are output on the weight display They are displayed in coded form Error x Display Signification cause Error 1 internal arithmetic overflow faulty calibration values Error 2 input voltage is above f s d overload Error 3 input voltage is above the permissible range of 36 mV However an error in the analog section in the load cell or a cable break is also possible Error 7 input voltage negative or incorrect load cell connection Error 8 ADU error e g hardware defective or overloaded Error 7 gt 0 l
64. Set span Or right softkey mv v display Enter Deadload 0 123456mvV V _The entry is followed by Setting Deadload 0 123456mvV V by gt 4 4 2 5 Set span urther keys Returns to 4 4 2 3 Set stepwidth Skips and goes to 4 4 2 5 Set span uit cancels the calibration after safety prompt 9 4 4 2 5 Set span set Span iyw _Load the scale and set the span with the softkey Load in the middle display Enter current load 3000kg Entry of the weight key is followed by display Setting Span 3000kg Subsequently gt 4 4 2 6 Calculate test Or right softkey mv v display Enter Span 1 23456 7mV V _The entry is followed by Setting Span 1 234567mV V Subsequently gt 4 4 2 6 Calculate test Further keys returns to 4 4 2 2 Set FullScale a skips and goes to 4 4 2 6 Calculate test Quit cancels the calibration after safety prompt 42 rel 1 10 PR 1713 4 4 2 6 Calculate test calculate test Test V v The left softkey Test calculates the test value display usus SEL 4 4 2 7 Exit calibration Further keys returns to 4 4 2 5 Set span A m skips and goes to 4 4 2 7 Exit calibration Quit cancels the calibration after safety prompt 4 4 2 7 Exit calibration Exit calibration
65. Show Version Setup display of version number in the bottom display line select with scroll Show Version keys e g Firmware Version PR1713 00 rel xx xx rev xx xx xxxx flash firmware BIOS Version Part of the operating program 4 5 10 Reboot Setup Reboot The system can be initialized via this menu Reboot Cold cold start with deletion of programs and tables Cold Warm WReboot Warm warm start Reboot starts the boot menu Reboot done completes the boot operation Cold V Warm WReboot PR 1713 rel 1 10 49 4 6 Config program set up menu Configurations in menu Config are made on the front panel console IEC 1131 program Config is used for determination of limit values fixtare memory printer interface and some parameters for batching with PR1713 The individual parameters are displayed successively with the scroll keys as long as they are between the selection markings For parameters which can be selected by pressing the Enter key the preset value can be entered If a selection list exists for the parameter the selection markings are at both sides of the preset value Config project Remarks 1 line parameter Vers Edit Print 2 line preset value report text 1 2 print layout start name value cycle number recipe now WP limit A 1 on A 1
66. URVEY s va ides des bae Po tar ev eei se riesen in due b to ee e ee Esse RN Eu ede 2 2 OPTIONS S edere tite voti attt s ds su ttis etit tte 2 2 1 Program extensions optional esses 22 2 Plug in cards and modules optiondl 5 e caa e ui huiles 2 34H OUSINGS oras Ree ena eed usn re AID M MEI edv eI d INSTALLING THE INSTRUMENT AND OPTIONS ee eene eee eee tenu neon eset ttes assesses esee esses esee 3 1 MECHANICAL PREPARATION ccccccssssseccccecccessssesseeecccceceausssecccecessuuasseeccccessauunseeecccessauunsseccceesssuunseccceesssuaaneeeceeeeuenes SED HARDWARE CONSTRUCTION lt 5 2 etie ave dow Ee us Eee aute Sue satus dee senis Gus ene bes achive E EE e NE e 3 241 Iistalling the options 34 iue de iu umen SENE 10 3 2 2 Cable gland and connection ae ine puke ee E an jes ie ede bete ein iren oe ede nose aee e ces 11 3 3 ON THE CONNECTING 12 3 3 1 Load cell cable cable junction box eee 12 3 3 2 External PC AT keyboard iie Seb ies 13 3 3 3 RS 232 Builtin interfaces coinein ane E E A A A A N EE A AE EE EEEE 13 334 PRIZ V4 Sera I O set ete Saas en aa e ais Das cats rete DE 14 3 3 2 PRI713 06 analog output card zu siino nde
67. V V can be realized on the console front panel or terminal of PR1713 Additionally the CAL hardware switch is provided in the instrument Calibration data changing download and flash functions only if the switch is open If calibration is active press gross key B for a 10 fold magnifier toggle 4 4 1 Calibration sequence The sequence is started with 4 4 2 1 Calibration 4 4 2 2 Set Fullscale is reached with New Or Modify Changing to the next item is with scroll down up to 4 4 2 7 Exit calibration or with scroll up key in an endless loop up to the previous menu item of these chapters The endless loop can be left with Quit without changes or as described in 4 4 2 7 after changes in order to cancel the new settings or to save it 4 4 2 Start messages When calling up the calibration various error messages can be displayed Ce oee Jumper is closed The jumper switch CAL is closed Tare activ The scale was just tared Callie T CL C eT SZ The scale is calibrated via another interface Weighingpoint in use The scale is just busy e g batching Otherwise selection if the existing calibration shall be modified or if a new calibration shall be started must be made 40 rel 1 10 PR 1713 4 4 2 1 Selecting the calibration mode Calibration New WModifyW Param New starts a new calibration with default values deadload
68. X XX X XX XX XXXX CALIBRATION IMIG BOX nox Zoo 092531251 033 323 A x 033 3kg Configuration Analog Filter off Meastime 2 00 Standst rn 1 00 d Overload 9d Digital Filter off Fcut 1 00 Zeroset rn 50 00 no below 50d Multirngmd off Standst ti 0 Zerotrk rn 0 25 d Stepwidth 1 Test mode Absolute Zerotrk ti 0 Zerotrk st 0 25 d Multirangl 3000 d W and M Disabled Tare timot 8 Multirang2 6000 d existe Fullscale 600 0kg Deadload 0 027408 mV V Resolution 8 774623 cd c Calipoint fixed Span 0 889043 mV V Resolution 11 39 o d Keypad Select item with cursor up down left right Change with Return to fiXed Set Fullscale Calibrate by Weight or Millivolts E Exit calibration The weighing point calibration mask contains all weighing point parameters They are classified as follows Configuration parameter Configuration During configuration the parameters which are not included into conversion of measured counts into a weight value are determined for operation of the analog part Calibration parameters Current calibration During calibration the conversion of the analog input signal or digital of measured counts into the weight value is determined The access functions Keypad are displayed below these two weighing point parameter groups 5 4 1 2 Leaving the weighing point calibration mask When leaving the mask decision what shall be done with the enter
69. a 7 47 Input ddress 83 Interbus Slave sess 28 30 Interbus S 7 24 44 47 interfaces os e ee ER teret 59 J JUNC ON DOK c 12 K Key nuni pee San ere 45 Keyboard nit Ma chi Rpt a e 13 L Tan gua ges d ete etia 33 45 Leaving Set Parameters esee 43 Leaving the weighing point calibration mask 65 licence octo E eto tea ees 47 licence number eedem ete este 60 Lanes Recipe bete neret 46 List of parameters and possible entries 61 Load cell tentes tes 12 Loading new firmware eee 38 LOB als 5 rp terre T 4 Low Battery Ch ck 2 iue es 46 PR 1713 rel 1 10 105 M R Measuring time oon eene 68 RAM xtension 3 npe daniel yeaa by 10 MEMO i eese ete dee er re eee tue p des 86 RAM extensiOn nnne 2 memory extension 7 B b60t nne 48 Menu structure 55 tot i en 7 46 ERROR 83 Recipe management seen 7 module testing seen nnne 87 Recipe simulation eene 46 gioi 33 Refresh Display 2 Heide tds 48 MOU lfitllg ote ert ete rtp eie te eec 8 relay output ire tr
70. ae parameters for interface Builtin or selected Protocol Protocol of interface e None No protocol e Xon Xoff e EWCOM V1 EW protocol V1 standard e EWCOM V2 EW protocol V2 multi program PR1740 e EWCOM V3 EW protocol V3 DDE server J e RTS CTS Hardware protocol e RemoteDsp Remote display string e W amp M Print Printer string The protocols EWCOM V1 or V2 or V3 as well as RemoteDsp W amp M Print can be allocated only once per unit They are not displayed any more if they are in use elsewhere Serup Bibi iira Make data rate and protocol equal to connected serial interface Baudrate Adjustable Baudrate 300 600 1200 2400 4800 9600 19200 Setup Builtin Data bits Bits 7 8 Setup Builtin Parity bit Parity None odd even Setup Builtin Stop bits Stopbits 11 2 Slave address A to Z is only selectable with EW protocol Setup Builtin Unit at the interface raw I O or terminal Device Raw I O printer remote display communication ANSI VT52 Setup Builtin character echo Echo Disabled enabled 4 5 3 Software parameters Setup Configuration of some basic parameters General specifications for Software Parameter parameters e g language console can be made 4 5 3 1 Language Language English Local Lan
71. alibration in one step Step 2 to step n are only repetitions of points 4 and 5 of the Calibration in one step Step by step calibration Proceed as described in points 1 to 7 of Weighing point calibration procedure This is followed by actual calibration 1 The command line displayed in the calibration mask is Unload Calibration by weight Unload and hit O or S to skip to quit E to end X to set fixed span to print The system offers the following replies Unload and hit 0 unload the scale and set the zero S to skip skip zero setting Q to quit cancel calibration without doing anything E to end calibrate and finish X to set fixed span set the fixed span P to Print print out the weight value PR 1713 rel 1 10 75 Set the zero e Unload the scale discharge e Press key 0 e PH1713 evaluates the data Now the following command line is displayed in the weighing point calibration mask Setting deadloads system saves the data Subsequently Setting deadloads Status OK the message is displayed during approx 2 seconds e Weight display goes to 0000 kg e of error repeat zero setting See point and 5 The following command line is displayed in the mask Unload Load Calibration by weight Unload and hit or to skip Q to quit E to end X to set fixed span P to print The system offers the following replies Unload and hit 0 unload the scale a
72. alog PR1713 07 I O 4 anal in 1 only 1 anal out PR1713 06 1 anal out Front PS PR1713 08 Keyboard PR1713 is digital BCD or BIN out PR1713 12 PR1713 15 digital 4 in digital 4 in 4 outopto 4 outrelais VO PR1713 13 PRiz20 i PR1713 17 external extension DlOSmast digital 6 in german 1 only Interbus S WP B i 8 out GND Keyboard d N seriall O PR1713 04 DIOS RS 485 Interbus S peripheral Distributed RS 232 i System Licenses Eus m Batching PR1713 20 PR1713 21 serial World PR1713 30 RS 232 Hardware PCprogram for PR1740 2d or PR1713 20 Protocol PR1740 11 standard special EWCOM PR1740 21 several 1 only 1 only PR1740 41 PRIT40 31 L 1 F Batch recipe PR1740 SEM MEN ipiam InTouch PR1790 or optional a PR1750 20 1 2 1628 s Complexbatching for DDE h InBatch PR1780 PR1791 13 Standard nd or i DDEserver PR1791 RTT ae t Phaseconfig PR1781 patria ASCII Printer InTouch 1790 PR1781 13 WaM 3 PR1791 13 IEC1131 Printer 2 DDEserver PR1791 Option programmed InTouch PR1790 interface T C J L Engineering PR1750 additionally programming PR 1713 rel 1 10 7 2 2 1 Program extensions optional Product PR 1713 20 Batching function with 1 recipe up to 255 components freely configurable
73. are displayed and can be changed The possible editing functions are displayed below e Save configuration Exit and save If changes were made the system asks Change modified I O s sure Press Y or N The changes are effective only after Exit The parameters for the serial interfaces are saved in EAROM List of parameters and possible entries selection e Selecting the serial interface Serial IO 1 2 7 Selecting the previous next serial interface Previous Next serial I O Protocol None X ON EWCOM Slave VI V2 V3 RTS CTS Remote Display W amp M Printer Number of data bits Bits 7 8 Parity check Parity None Odd Even Number of stop bits Stopbits 1 2 Transfer rate Baudrate 300 600 1200 2400 4800 9600 19 2 PR 1713 rel 1 10 59 e PR1713 slave address Slave adr space A to Z e Terminal type Devicetyp Raw I O Ansi VT52 Echo Echo Disabled Enabled A PR1713 can be equipped with max 7 serial interfaces For a survey see next chapter Dependent of selected protocol and interface defined default settings are made by the system 5 2 3 1 Survey physical interfaces PR1713 can besides the built in interface be equipped with max 6 additional serial interfaces provided that the 3 options sockets are fitted with 1713 04 The interface no is allocated from TTY1 to TTY6 via software All interfaces can use each protocol but EWCOM Remotedisplay and W amp M prin
74. ask Calling up mask Weighingpoint is done from the Main Command Level by pressing key W PR1713 00 RO XD SOUCIS ORO DORR OR Weighingpoint IMIG SOK sooox 09854 gil Roe Ss 005 4kg Bx TB 033 3kg Keypad 0 Set Zero I O Tare In Out Select Display T Tare G Gross N Net Test F Flow Z Zeroset D Diff S Setp Print C Calibration A Additional WP s E Exit The functions of this mask are e Weight display and function keys for the PR1713 weighing points e Calling up sub menus masks Weighing point calibration mask Calibration Additional weighing points Additional WP s Return to the main menu is with E E Exit Weight display and function keys for the PR1713 weighing points Weighing point selection is by means of the two cursor keys T and J The actually selected weighing point is highlighted by inverse display The weight values of 2 weighing points can be displayed in the weighing point mask If more weighing points are defined in PR1713 scrolling through the display field can be done using the cursor keys 1 4 The function keys relate to the instantaneously selected weighing point Mask description Gross net tare weight display B N T Select Display The gross net or tare weight can be displayed by pressing the relevant key with the scale tared This is shown by display of the relevant letter Setting the zero is done with key 0 Set Zero When the scale was set to zer
75. csseecesceceseceseeceseseeceseeseseesenaeeesaes 86 5 8 2 Show hardware 87 5 6 3 Testing the input and output 87 5 8 4 Printing all configuration d ta irai tete ee toe 9 25 0 OPERATING LEVEL NDERIT de bekeeesd eT eto 92 quue 93 6 ANALOG PART A D CONVERSION etes e estet te aere av aee dv abe e TA e tee Ted 93 6 1 1 Accuracy and stability eee dte died see deti Edad o e Eee gode pee etae Mes 93 OT 22S AKIA TANI DARE atest ie elas fe 93 UNSER Kaia 93 6 1 4 Safe Conditlon i i E OM a eat o SEES EM aes eg ase et heath ee Ue dee E 93 6 1 5 Certificate of type approval eid etie dg ecere td eS diede detenta tbe ve Po gode petuo rogo des 94 0 1 0 Locattom of seals tft t tede tat tee eeu ect e p edet ete ap tege Bene e Wheeden eet eet eed pe ne ue 95 6 2 DIGITAL PART cei REEL ENSE ERE RR EIU TERI ERR TRE ONTON 96 6 2 F Display EE 96 6 2 2 Keyboard ite uide d e e ee de e tete oo Ede og Eee Ea aE EaR 96 6 2 3 Exiernal keyboards s tt tette eet nest ee ii tede eA saath 96 6 2 4 Built in RS 232 interface 96 6 2 5 Power supply PRIVIS 00 x deett d ee Her pedro dte tte pe e regere
76. cursor up down left right Change with Return to FiXed Set fullscale Calibrate by Weight or Millivolts E Exit calibration Calibration is finished The data must be saved Proceed as described in points 9 and 10 of the Weighing point calibration procedure 5 6 7 2 Subsequent zero correction without weights Proceed as described in points 1 to 7 of the Weighing point calibration procedure This is followed by the actual calibration 1 The following command line is displayed in the calibration mask Deadload Calibration by mV V Enter deadload mV V Q to quit S to skip _ Enter deadload mV V Enter the deadload in mV V Q to Quit Enter key quit the calibration without doing anything S to Skip Enter key skip the tare entry 2 Enter the deadload in mV V Enter the deadload with comma or point Press the Enter key to complete the operation 1 e PR1713 evaluates the data Now the following command line is displayed in the weighing point calibration mask Setting deadloads the system saves the data Subsequently Setting deadloads Status OK the message is displayed during approx 2 s e The weight display does not change The following command line is displayed in the calibration mask Span Calibration by mV V Enter span mV V E to exit _ Enter span mV V enter the span in mV V E to Exit enter key 1 no entry finish calibration 4 Setonly the z
77. d in the mask header Configuration of WP B PR1713 00 4 999 9 9 99 OK 9 BOX Configuration of WP B IMIG BOX somo O098s31 85 T Update Time 6 50 msec A Input address 1 E Exit configuration Q Quit configuration Enter Input address 1 E to exit 2 address must be 1 and lt 4 Selection of the individual parameters is by the relevant letter e time for weight display T Update time Entry is in n 50 msec With an entry of e g 6 the displayed weight values are updated at intervals of 300 msec 6 50 msec Permitted range 2 20 Error message with faulty cycle time entry Bad number e PR1720 00 address at the Interbus S Input address Permitted range 1 4 according to the position at the remote bus e Finish the configuration and save the values E Exit configuration e Leave the configuration without saving the values Quit configuration If parameters were changed the following prompt is displayed Abandon changes sure Press Y or N 5 7 2 Customer specific weighing point With a customer specific weighing point weight measurement is done by an external weighing point which is connected via an interface to PR1713 The weight must be provided to the PR1713 batch program on a definable SPM address by a customer specific IEC 1131 program Gravimetric weight measurement The weight values can be provided as follows The weight values are read i
78. dashes range 1 range 2 range 3 in front of the weight value During Calibration the multirange function is principally switched off With weights amp measures application a label for the range must be placed above the 1st digit of the weight display 4 4 3 2 Leaving Set Parameters Save configuration After Qui key Save data Save WnoSaveW Undo noSave data Parameters are stored in EAROM after Save Undo restore 44 rel 1 10 PR 1713 4 4 4 External Wp Additional 2 weighing point External Wp B User defined user defined PR1720 PR1720 via Interbus S interface in PR1720 none no weighing point B The user defined weighing point B gets data via SPM variables which are output as weight The _scale is defined with the following points Fullscale f s d can be edited after pressing key 1000 kg digits dimension with More key Stepwidth stepwidth 111 2 5 10 20 50 overload scale overload range 0d in d Minwgt Min weight for starting a print order 0d corresponds to don t print below Scale weight cnt Scale resolution 1 kg 1 cnt weight per count Update time 50 ms Multiples of 50 ms define the measuring time 6 input address MD SPM variable for weight value 32 free address for a double word PR1720 as weighing point B requires the following specificat
79. decimal or 3 byte binary with application program PR1713 12 max 3 cards 4 inputs and 4 outputs Digital interfaces galvanically isolated via optocouplers Inputs active or passive Configurable by software set up PR1713 13 DIOS master digital I O system for connection of PR 1720 as 2 weighing point and as bus interface for max 265 additional dig I O only 1 card Master function based on Interbus S standard for control of digital I O A PR1720 can be used as a 2 weighing point at the DIOS card Automatic detection of the connected modules The max possible number of ports is limited to 256 bits or 4 modules The card has integrated termination resistors PR1713 15 4 optocoupler inputs similar to PR1713 12 but configurable relays output 4 relay outputs The following options can be inserted on print 2 below the front panel Product PR1713 05 1 MB static RAM The memory extension is detected after installation and cold start PR1713 14 Ethernet in preparation PR1721 field bus interface connecting unit e PR 1721 01 Profibus DP slave max transmission rate 1 5 Mbits e PR 1721 02 Interbus S slave PR 1721 04 DeviceNet slave For details on the products see the relevant chapters of this manual 8 rel 1 10 PR 1713 2 3 Housing PR1713 is accommodated in a stainless steel multi purpose housing 288x144x130 mm of protection type IP65 It is suitable
80. ding levels 0 gt 1 or 1 gt 0 PR 1713 rel 1 10 51 If the values for ON and OFF are equal the limit value output is switched to ON when exceeding the limit value 2900 kg OFF 2890 kg ON Limit 1 Limit 2 mit 4 6 5 Printer interface One of the free PR1713 interfaces Builtin or interface card can be defined as printer interface A serial ASCII printer can be used Printer device interface via which all print outs are made Builtin Builtin Select the sub menu with the Enter key J The selection markings in the bottom line permit selection of one of the available interfaces Selection is dependent of the additional interface cards provided in PR1713 Printer device Sequence Builtin Slot 1 RS485 Slot 1 RS232 Slot 2 Builtin the RS232 Builtin Slot1 RS485 the RS485 on the first additional interface card is TTY1 Slotl RS232 the RS232 on the first additional interface card is TTY2 Slot2 RS485 the RS485 on the second additional interface card is TTY3 Slot2 RS232 the RS232 on the second additional interface card is TTY4 Slot3 RS485 the RS485 on the third additional interface card is TTY5 Slot3 RS232 the RS232 on the third additional interface card is TTY6 batchrep auto prt no printing but only the last report is kept in memory off auto print immediately the last report is kept in memory
81. e Time Be ZETO COITeCtiOD ceeesseesceccceceessvssssvscvcccecensscesveccceees 76 V Z ro absees dens ovepdesssveadeas oes 68 ITUR ERR RTI RA 12 ete te e Pent 46 Volumetric weight measurement esse 83 PR 1713 rel 1 10 107 7 5 Hint for customer feedback Dear customer We hope that this product meets your requirements However your comments and wishes for improvements are always welcome Moreover information on your application would be greatly appreciated For this purpose please send your comments to GWT GLOBAL Weighing Technologies GmbH Abteilung Marketing Meiendorferstrasse 205 22145 Hamburg FAX 040 67960 608 Our Internet address is http www global weighing com 108 rel 1 10 PR 1713 Error description PR1713 Problemreport Software Firmware Version Rel Rev e g Rel 1 02 3 Rev 31 12 1999 Bios Version Rel Rev Application SW PR1740 PR1750 PR1791 Hardware RS232 RS485 Slot1 PR17 Use Protocol Slot2 PR17 Use Protocol Slot3 PR17 Use Protocol Slot4 PR17 FB Protocol Error Messages on Display Registers if given SR FMT ADR DO D1 D2 D4 D5 06 D7 AO Al A2 A4 A5 A6 AT If applicable
82. e electronics of PR1713 is accommodated on two circuit boards connected via cables Connection of main print 2 and connecting board print 1 in the basic housing is via two 20 core flat cables and a 4 core cable The board accommodates the processor with its components loaded Flash EPROM memory modules interfaces and serially connected display For mounting the field bus interface PR1721 xx a 50 pole connector is provided Two free DIL sockets are provided for mounting the RAM extension The connecting board accommodates the power supply transformer and switching power supply with firmly fitted power terminal the analog part for the load cell the detachable connectors and the three sockets for options The standard connector for the PC AT keyboard is connected on the circuit board with by means of 4 leads 3 2 1 Installing the options The connecting board is provided with three identical sockets double row 2 25 contacts for options The expression for the sockets from left to right is I O Slot 1 The plug in card connections are taken identically from each socket to two terminal rows The connectors with dual terminal rows are in front of each card on the connecting board The pin allocations are different dependent of built in interface card The options are detected automatically after cold start Installation layer side left component side right Attention position plug exactly above contact pins Set both rows correctly in
83. e output informs the instrument that the bus is continued Communication is transmitted further to the next unit at bit level 3 4 4 3 PR1721 04 Device Net Interface PR 1721 04 Device Net V x V 33 PR1721 03 CAN BUS PR 17xx S Transceiver Use screened twisted bus cable 2x2 Bus termination at both ends by resistor 120 PR1721 04 takes 33 mA from the DeviceNet bus supply The EDS file for PR 1721 04 can be copied under our Internet address our website in Internet http www global weighing com PR 1713 rel 1 10 31 4 PR1713 00 COMMISSIONING After switching on possible error message for the fist time No valid RAM data if battery jumper is not set see 3 4 1 this operation must be followed by a cold start Cold and clock date and time adjustment 4 1 Data saving power failure The configuration calibration data are stored in a non volatile memory EAROM Data saving in EAROM is by command configuration calibration A battery is built in A power failure is registered with a system event PLC address Additional write protection switch see 3 2 for the calibration data is provided Default Calibration data Default Configuration data Modified Calibration data Configuration data RAM Calibration data CONFIGURATION 4 1 1 Calibration data Adjustment of f s d values measuring time weighing parameters The calibration parameters must be
84. ed weighing point parameters must be made Leaving the mask is always started with command e Exitcalibration enter letter E Now the system offers the following reactions see below line Keypad in the figure Keypad S Save N Dont Save Q Quit calibration C Stay on calibration These are e Saving in EAROM Save Enter letter S e Use data no saving Dont save Enter letter N e Quit calibration without saving the entries data Quit calibration Enter letter Q e Staying in the mask Stay in calibration Enter letter C When leaving the weighing point calibration mask with Q Quit calibration all entered weighing point parameters are overwritten with the previously temporarily saved weighing point parameters The two functions Save and Dont save in EAROM are described on the following page e After leaving the weighing point calibration mask return is to sub menu Weighingpoint 66 rel 1 10 PR 1713 5 4 2 Saving the weighing point parameters in EAROM After configuration and calibration of a weighing point all relevant weighing point parameters can be saved a non volatile EAROM Saving of the weighing point parameters in EAROM is from mask Calibration only possible with switch CAL open e For finishing the calibration Exit calibration Enter letter E e From the reactions offered by the system select saving in EAROM Save Enter letter S The data are saved in the EAROM e For saving the two steps must
85. eldbus interface The fieldbus interface RS 485 differential is galvanically isolated The maximum transmission rate is 1 5 Mbit s The fieldbus protocol is realized by a plugged in subunit chip The software for the fieldbus module is activated when switching on the basic unit The interface board is delivered with two PG9 glands Attention Since December 1999 the connectors of the PR1721 module has been changed e Installation The fieldbus connecting unit comprises a card with processor and logic and 13 pole connecting unit After plugging in the card into the main p c b caution 50 pole connector at the universal module see page 27 the board must be fitted at the two mounting posts with screws Cable connection The blind plugs in front of the connector strip must be replaced with the PG9 cable glands Bus connection is by means of cables through the metal glands PG gland to the 13 pole terminal strip at the fieldbus module Connect the cable screens completely and exclusively to the glands The cable conductors must be tied together with a cable strap 15 55 1s 83 terminals Interbus S Ensure that the potential compensation between the instrument and the preceding unit in the bus is provided PR 1713 rel 1 10 29 e Connection of the fieldbus PR1721 01 PR 1721 02 mm 1721 04 PROFIBUS DP InterBus S on request only Device Net Con Test II
86. erating manual 4 3 1 Configuration area Setup In menu Setup the most important PR1713 operating parameters can be adjusted Configuration of the unit depends from the provided application and the built in options the licenses cards The menu items are adapted to the equipment of PR1713 Calibration of the internal WP is in a dialogue During calibration all parameters which can be entered are checked Storage of values which do not make sense is not possible However compliance with the relevant calibration standards must be checked by the operator calibration officer If calibration must be protected against overwriting after saving weights amp measures applications the CAL switch in the instrument must be closed for this disconnect the unit from the power open it close the switch 3 2 and connect the unit PR 1713 rel 1 10 35 Configuration of PR1713 is made without additional terminal via front panel display and keyboard Simply use the scrollkeys and the softkeys in connection with the alphanumeric display Within setup menu all items in each level are scrolled in an infinite loop which can be left to the next higher level by pressing the Quit key Exception the calibration loop must be ended by the function keys Save noSave Undo A displayed or selected information is entered by pressing the enter key The set up menu is structured as follows 4 3 1 1 Setup menu Part 1 Weighing point calibration
87. ero finish the calibration E to End Press key E e PR1713 evaluates the data Now the following command line is displayed in the weighing point calibration mask Calculating test the system calculates the test value Calculating test Status OK e The new gross weight value is displayed 0027 kg Subsequently the standard command line is displayed Keypad Select item with cursor up down left right Change with Return to FiXed Set fullscale Calibrate by Weight or Millivolts E Exit calibration Calibration is finished The data must be saved proceed as described in points 9 and 10 of the Weighing point calibration procedure 80 rel 1 10 PR 1713 5 6 8 Error messages in the calibration menu no standstill value is invalid ADU Error current load is below deadload Current load is above full scale Illegal stepwidth FSD not multiple of stepwidth Fullscale is below calibration point overflow in converting units underflow converting units Input voltage above max not enough counts per d device not ready protocol error BCC error Canceled no standstill was reached during calibration the parameter is too high or too low Proposal of the highest permissible value with setting max general error ADC load cells occurs when entering the SPAN value The deadload was removed Subsequently SPAN is below zero occurs when entering the SPAN value
88. erotrack time 100 M enter value only Tare timeout 100 M enter value only Standstill range 0 00 d 10 00 d enter value only Zeroset range 0 00 500 00 d enter value only Zerotrack range 0 004 500 00 d enter value only Zerotrack step 0 00 10 00 d enter value only Overload 0 9999999 d enter value only Don t print below 0d 9999999 d enter value only Config Operation call up IEC 1131 program CONFIG if provided see 4 6 f f External WP additional 2 weighing point none or connection of PR 1720 or user defined User defined user defined WP Fullscale 0 000100 9999900 kg t Ib g dimension with More enter value Stepwidth 1 2 5 10 20 50 enter Overload 0 9999999 d enter value only Minwgt 0 9999999 d enter value only Scale weight cnt 1kg 1cnt Scale weight 1 9999900 kg t Ib g dimension with More enter value Scale counts 1 9999999 enter Update time 50ms 2 20 enter Input address MD 1 255 enter PR1720 PR1720 as WP B at PR1713 13 DIOS Interbus S Update time 50ms 2 20 enter Input IBS address 1 32 enter Set Clock adjustment of date and time oues See next page 36 rel 1 10 PR 1713 Part 2 Interfaces communication softwareparameter
89. eters mask Calibration indicates the access functions which are enabled now see figure on the next page CAL switch in closed position weighing point parameters protected no download and flash When switching on the PR1713 00 e calibration saved in the EAROM only with valid calibration data is loaded e otherwise factory setting and factory calibration are loaded When calling up mask Calibration the weighing point parameters are protected The weighing point parameters are only displayed in mask Calibration With W amp M weighing systems this CAL switch is sealed in compliance with the calibration standards 5 4 1 1 Calling up and display of the weighing point calibration mask Calling up weighing point calibration mask CALIBRATION e Weighing point selection is by means of the two cursor keys T and J The actually selected weighing point is highlighted by inverse display e Calling up the weighing point calibration mask is done by pressing key C Calibration If a production is running this call is disabled message WP is in use When calling up mask Calibration with the CAL switch open tare memory and zero setting memory are erased Moreover the following functions are disabled during weighing point calibration test automatic zero tracking taring and zero setting PR 1713 rel 1 10 65 The weighing point calibration mask is shown below PR1713 00 Rel X
90. ew line 2 the contents of report text 2 new line newline 4 6 3 Batch parameters Start name Ifa recipe name is entered no prompt for the name is displayed when starting the batch The recipe is started with this name 50 rel 1 10 PR 1713 Start value lifa set point lt gt 0 is specified no prompt for the set point is displayed 0 kg when starting the batch The recipe is started with this set point The recipe start procedure stores the last used setpoint for each recipe start cycle number lIfa number of cycles lt gt 0 is entered no prompt for the number of cycles is displayed when starting the batch The recipe is batched as many times as specified start recipe now With start batching starts immediately With inquiry the question Scart Start recipe now is displayed before a batch is started Start recipe now could be used to enter an setpoint for this recipe with no need to start a production This could be done by e g digital input and a recipe number must be selected After that the required amount of production can be done by closing a switch The operator can easily change the start up values at the console 4 6 4 Limit values 2 limit values with independent values for on and off for monitoring are provided for weighing point A in PR1713 i e 2 WP B The limit value as limit 1 or 2 of weighing point A or B can be defined freely for a weight w
91. face batching functionen on off Printer Device at Builtin 510 5485 51011 RS232 Slot3 5232 Operator Device at Builtin 510 5485 510 RS232 Slot3 5232 Fieldbus Parameter Fieldbus configuration of the optional fieldbusinterface PR1721 xx PR1721 protocol none Interbus S Profibus DP DeviceNet Interbus s _ forPR1721 02 IBS cycle 1 50 enter Profibus DP for PR1721 01 Profibus DP address 1 126 enter DeviceNet forPR1721 04 DeviceNet baudrate 500k 250k 125k DeviceNet MAC ID 0 63 normal 1 60 Scale interface __ select Disabled Enabled 8 Byte standard interface between scale and fieldbus Show Boardnumber display of the instrument serial number for licences licence number management Show Add Delete Print Setupdata initialization data print out on the selected interface Licence Setup Refresh Display refresh display all segments on Show Version version number display of firmware und BIOS Reboot selects cold start warm start boot menu 4 3 2 Boot menu The boot menu is set up sub item Reboot When pressing foil covered Stop key during instrument switch on a boot menu is displayed on the unit f warm start is possible 5 pressed Cold all programs and tables loaded in the memory are deleted Cold V Warm VW Flash Flash program loading also parts Warm all da
92. fixed span P to print e Repeat the calibration step as shown in section 4 Apply the calibration weight Load and hit Return Press the Enter key see 4 e Setthe fixed span X to set fixed span If the calibration cannot be finished correctly for any reason press key X To avoid operator errors a prompt is displayed and must be replied with Yes No Y N The system executes the command Subsequently the command line as shown in point 5 is displayed again Print the actual weight P to Print Press key P The system executes the command Subsequently the command line as shown in point 5 is displayed again e Setthe zero Unload and hit O If necessary zero setting as described in point 2 can be repeated e Finish calibration E to End Press key E Calculating test the system calculates the test value Calculating test Status OK 74 rel 1 10 PR 1713 Subsequently the standard command line is displayed Keypad Select item with cursor up down left right Change with Return to FiXed Set Fullscale Calibrate by Weight or Millivolts E Exit calibration Calibration is finished The data must be saved Proceed as described in points 9 and 10 of the Weighing point calibration procedure 5 6 6 2 Step by step calibration Description If the scale can only be loaded with a relatively low calibration weight e g 1096 of full scale step by step calibration is required The
93. for table top installation wall or panel mounting The housing can be opened forwards Keyboard display and main print form a unit with the front panel The front bezel is 5 mm thick and held in position by means of 6 screws A rectangular panel cut out 278 mm 134 mm is required for front panel mounting The cables are entered via 9 stainless steel EMC glands on the housing rear Unused cable glands must be shut with blind plugs IP 65 Power cable and external keyboard excepted all connections are made via internal screw terminal connectors The cable glands for power connection LC connection and Builtin are always provided The remaining glands are divided as follows 2x for the field bus option 1x for each of the three options For connection of the options three 16 pole connector blocks with identical pin allocation 2 terminal rows each with 8 terminals are provided The PR1721 xx module has an 18 pole terminal row The socket for an external PC AT keyboard with standard round connector is accessible from the rear after removing the protecting panel CAUTION with the PC AT keyboard connected protection type IP 65 is not met any more DL IL ME ES eR MM ibe Aa CHIOE FI Cs Pres ite 7 8119 EEG I CEIS ederi e La s aa i maana a m m m m a e e PR 1713 rel 1 10 9 3 INSTALLING THE INSTRUMENT AND OPTIONS Bef
94. g for remote display programs PR1740 PR1791 e Atexternal terminal an operator can check the analog digital converter with analog test Communication protocols for the Internal RS 232 or the optional RS 232 485 3 EW protocol remote display string e printer string Fieldbus slave option additional by PR1721 xx Extensible by means of licenses e g Licenses are activated via a license number which is related with the board number of PR1713 PR1713 20 Batching controller one recipe max 255 lines PR1713 21 Batching with several recipes max 255 lines Licenses for recipe manager PR1740 License for standard batching module S 88 License for DDE transactions with Windows NT License for programming PR1750 in connection with device PR1750 is available on the CD Complementary SW TOOL BOX updates are available in the Internet PR1750 can be used free of charge without license for up to 64 lines IL code only one task possible in the PLC resource Operating and recipe resource not programmable 6 rel 1 10 PR 1713 2 2 Options PR1713 Periphery PR1713 05 1 MByte staticRAM Option 5 RAM Option 4 PR1721 01 Fieldbus Profibus Slave DP n e D D Fieldbus master Bry PR1721 04 DeviceNet PR1721 02 Interbus S Weight Display Option 3 PR1713 14 Option 2 Max 3 Option Cards of Ethernet Front Option 1 in preparat Display a an
95. g and manual zero setting will not function any more In these cases subsequent zero correction is possible without recalibrating the weighing point For this call up the weighing point calibration and set only the deadload Calibration must be skipped Zero correction Proceed as described in points 1 to 7 of the Weighing point calibration procedure This is followed by actual calibration zero correction 1 The following command line is displayed in the calibration mask Unload Calibration by weight Unload and hit or to skip Q to quit E to end X to set fixed span P to print The system offers the following replies Unload and hit 0 unload scale set the zero S to skip skip zero setting Q to quit leave the calibration without doing anything E to end calibrate and finish X to set fixed span set the fixed span P to Print print out the weight 2 Set the zero e 1 Unload the scale e 2 Press key 0 e PR1713 evaluates the data Now the following command line is displayed in the weighing point calibration mask Setting deadloads system saves the data subsequently PR 1713 rel 1 10 77 Setting deadloads Status OK message is displayed during approx 2 seconds The weight display goes to 0000 kg e case of error repeat zero setting See point 3 3 The following command line is displayed in the mask Unload Load Calibration by weight Unload and hit O 8 to skip E to e
96. ge sources When selecting a different supply voltage and when replacing the loadcell fuse the unit must be disconnected from all voltage sources 1 3 4 Earthening Earthening of the unit must be via the protective earth conductor PE 1 3 5 Protective earth The connecting cable of the unit must comply with the regulations in accordance with VDE 0411 or EN61010 The power cable must contain a protective earth conductor which must not be interrupted inside or outside these units e g by using an extension cable without protective earth The protective earth must be connected with terminal PE in the power connecting block Before commissioning acceptance of the installation by a technically responsible expert is required 1 3 6 Power connection PR1713 00 The unit is designed for AC power supply 50 Hz 60 Hz with supply voltage 230 V 115 The adjusted operating voltage must correspond to the nominal power voltage Changing over from 230 V factory setting to 115 V is done by means of a rotary switch which can be actuated using a screwdriver Turn the switch to the required voltage marked below the arrow Power connecting terminals supply voltage selector switch and transformer are located in the housing bottom left above the row of cable glands Caution The power cable conductors must be tied together with a cable strap shortly before the terminal block As the unit has no power switch it is ready for operation immediately after co
97. ghest digit 1 1 1 1 F dec value 15 1 0 0 1 dec value 9 Q 8 Q 4 Q 2 Q 1 10 8 Q 4 Q2 Q1 highest number FFFFFF 999999 Q58 Q01 Q58 Q01 Plug X104 supplies the data bits Q01 to Q48 in 5 decades with 20 wires plug X105 supplies the highest data bits Q51 to Q58 reference potential and the input PR 1713 rel 1 10 23 Input An input is provided to control all 24 output bits To enable or disable high resistive the output the input signal is fed to pin 5 Enab of the 8 pole plug On delivery the input of the module is configured to work with 5 V logic active high A positive Enab signal enables the output permanently with open or grounded input the output is controlled by the application program By solder pads J103 and J104 the logic level is defined with an open J105 the input is disabled Solder pads J100 J101 and J102 are factory set for the output type and may not be changed The enable signal DEEXT and the setting of solder pads J106 J107 and 108 can be detected by software This requires to develop a special application program in IEC 1131 N 0 0 0 0 0 0 0 0 0 0 ooo oo ooo o J103 J104A J104B mode logiclevel for data enable 1 input o 5V IL 31V 5Vmod c c 0 5 mA 5Vmode c o c lt 1 5V 0 3 mA 24Vmode o c o 24V 516V 1 0 mA 24Vmode o o c 24V lt 10V 0 5 mA o open c closed
98. ghing point module generates a message e g no standstill no5tAnd 5 5 14 Maximum permissible overload Overload Entry is in d permissible range Od to 9999999d 5 5 15 Min weight limit for print out no p below Entry in p permissible range Od to 9999999d 5 5 16 Stepwidth scale divisions Stepwidth Step widths 1 2 5 10 20 50 5 5 17 W amp M mode W amp M W amp M mode Enabled non W amp M mode Disabled 5 6 Weighing point calibration During calibration the relationship of display and measured variable weight is determined This relation is determined by the two entries e Deadload weight of the empty scale Deadload and e Scale measuring range Span During calibration these two parameters are determined by e a physical weighing operation weighing point calibration with weights or by e entry of the equivalent input voltage in mV V or weighing point calibration without weights When calling up mask weighing point calibration with the CAL switch open tare memory and zero set memory are erased Moreover the following functions are disabled during weighing point calibration Test automatic zero tracking taring and zero setting 70 rel 1 10 PR 1713 5 6 1 Weighing point calibration parameters The weighing point calibration parameters are described below The entries and the corresponding error messages are described in the following sub sections FullScale Fullscale The full scale value determine
99. guage Selecting the dialogue language for the operator not for configuration English default Default alternative language German 4 5 3 2 Key timeout Time out for display of net and gross display mode function keys 1 20r 3 sec Key timeout 2 sec 46 rel 1 10 PR 1713 4 5 3 3 Low Battery Check x Battery test result on weight display weak On Off 1 min repeat cyclically each minute 4 5 3 4 Lines Recipe Lines Recipe Maximum number of lines for recipes 34 1 255 4 5 3 5 Recipe simulation Recipe simulation on off For starting recipes with modified batching modules recipe simulation can be switched Recipe simulation on 4 5 3 6 Report to Configuration item for reports in the batching device The queue of batch reports is limited to a maximum of ten entries In a case of error in communication or printer the operator is informed and asked if he wanted to delete the oldest report Report to Specify destination for reports select with scroll keys for communic amp proloc communication PR1740 and Proloc local printer communication Communication PR1740 proloc Proloc local printer stand allone none No reports for devices without local printer PR1740 4 5 3 7 Tare key Tare key from the front panel is possible front panel console Enabled
100. he required parameters Adjust according to the interface configuration 5 1 2 1 Adjusting the terminal emulation program Start programm Hyper Terminal Enter Name in the 1st dialog window button OK Select direct connection via COM1 in the 2nd dialog window at connect via button Select port COM2 if the MOUSE is connected to The 3rd dialog window is the registry card Data transmission Settings button OK Setting Bits per second 9600 Data bits 8 Parity none Stop bits 1 Protocol XON XOFF 54 rel 1 10 PR 1713 5 1 2 2 Switch on messages The terminal output after instrument switch on is the Initialization message followed by the Main screen Instrument and version message date time main menu PR1713 00 eub SENSE Main Command Level Mo 2 C Configuration W Weighingpoint S Service 5 1 2 3 Terminate terminal emulation program Before switching on the PC or before closing the terminal emulation program return to the main menu If the PC is switched off in a sub menu instead of the main menu the full mask may not be displayed when starting the terminal emulation program In particular information on the operating and editing functions are missing Press space bar to display the mask at full size 5 1 3 Main Command Level menu structure PR1713 00 IR IL SOK 4 SOE SOK SOK ROKR SR ROK Main Command Level lo sk OK eK 092315
101. iensedecmeieeruxa ee NaveeuiEaiemeuteiiieiB ei BI IS 100 6 6 1 Interbus S Profibus DP DeviceNet eene enne nnne nennen nennen trennen estne enne ener 100 6 6 2 GSD file for PR1721 Profibus eene eee rennen enne nnne 101 6 6 3 EDS file for PR1721 DeviceNet cccccccscessscessceceesnscstsnsecsnnceceusnsecsnseceseancesenseecensesestancessnteesenenenseseseenseseneese 102 TARNNEEX erc E A N 103 TA PR1713 00 SPAREPARTS 5 inet ee HERE RR ERE HH 103 7 2 OTHER PR T7 13 DOCUMENITS sie eicere eee rtr tee ea PR tee eri ex ERE ee eere gae 103 73 GLOSSAR Iulii i ir 103 gi D qM 104 77 5 HINT FOR CUSTOMER FEEDBACK csccccccsseccccesscccccsseeccscceeccsceueccsecsecceusueccsceeccsseeccseueccsseecssseueccsseueccsseueessesneess 107 PR 1713 rel 1 10 1 1 SAFETY HINTS ELECTRICAL PROTECTION CLASS This instrument was built and tested in accordance with the safety regulations for measuring and control instrumentation for protection class protective earth connection according to IEC 1010 EN61010 or VDE 0411 The instrument was delivered in safe condition To maintain this condition and to ensure safe operation the operator must follow the hints and warnings given in this documentation 1 1 Application of the instrument PR1713 is inte
102. ile DescText PR1713 CreateDate 11 24 99 CreateTime 11 28 26 ModDate 11 24 99 ModTime 11 28 26 Revision 1 0 Device VendCode 560 ProdType 100 ProdCode 1713 Vendor Code Product Type Generic Product Code MajRev MinRev VendName GWT GLOBAL Weighing Technologies GmbH ProdTypeStr Weigh Scale ProdName System Weighing Controller Catalog PR1713 Major Rev Minor Rev NW dud l e e IO_Info Default 0X0001 PollInfo 0x0001 1 1 Inputl 8 0 0x0001 Input Data 0 WOM The Slot 4 input data Help string Up to 8 bytes All bits significant Poll only connection X Ur 4 Outputl 8 0 0x0001 Poll only connection Output Data 0 om The Slot 4 output data ParamClass MaxInst 0 Descriptor 0 CfgAssembly 0 Params EnumPar Groups PR 1713 rel 1 10 7 ANNEX 7 1 PR1713 00 Spare parts Description _Service code number MAIN PRINTED CIRCUIT BOARD POWER SUPPLY ANALOGUE PART I O SLOTS 5312 216 98338 DISPLAY PRINTED CIRCUIT BOARD MICRO PROCESSOR PART PLEASE OBSERVE BOARD NUMBER LICENCE 5312 216 98339 FRONT FOIL KEYBOARD 5312 456 90450 DISPLAY TUBE CX 050 for GWT 5312 131 98011 DISPLAY FILTER SCREEN GREEN 5312 480 38012 BATTERY LITHIUM 3V CR2354 ON MICRO PROCESSOR BOARD 5312 138 18012 FUSE 250 MAT LOADCELL RIGHT S
103. ing the weighing point parameters temporarily eese esee eee eene eee nnne 66 5 5 WEIGHING POINT CONFIGURATION eeeeeeeennnnnnnnn nn nnns nnns nsns nsns sss ttt sss sss E EEE EEE EEE EEE EEE EEE EEE EEE sensns sess nsns sss s 66 5 5 1 Editing functions for parameter entry eese 66 5 5 2 Filter Analog Filter uae PH eee 67 5 5 3 Analog test mode Tesimode cies eee de pe dtt cet eed dee het E et ere ore eed 67 3 2 4 Measuring time Meastime ui d LE HL EE EIU 68 3 9 5 Sfandstill dete CON ie a itt erae sero deser dle ila eee be e e TAGE ofan de 66 PR 1713 rel 1 10 5 3 6 Z ro Set rangez LZ CVOSEL viii ice de ed eel Sache A dee eno bial ee na de nd ease EE UN E Eee een 68 5 5 7 Automatic zero tracking eeu eee te utet E Pt ERR LE es 68 5 5 8 Automatic zero correction switch on off eese esee 68 5 5 9 Zero tracking range etat eeseis Feste 68 5 5 10 Zero tracking stepwidth Zerotrk st eese 68 5 5 11 Zero tracking interval Zerotrk ti eese 69 5 5412 Multirange scale eei e ttp tee ee m e a fee e e e ea deus e eoe tote 69 3 5 13 Tare time out Tare timot isses n eed ete IRE See Ree aE EET REEE e aniei kaio 69 5 5 14 Maximum permissible overload Overload eese eee entere nennen enne nennen
104. ions Update time 50 ms Multiples of 50 ms define the measuring time 6 1nput IBS address The Interbus S remote bus address indicates which module is 1 4 PR1720 CO The additional weighing point is stored or canceled with selection Save Extern WP data WEB AZ V W 4 5 Configuration of not weighingpoint parameters The configuration of all parameters which does not belong to the internal weighing point is divided into several sections see 4 3 1 1 Setup Menu 4 5 1 Set Clock For adjusting date and time select Time or Date with the scroll key The enter key opens the fields and sets the new data Set Clock actual system time changing is possible after pressing key setting Time 05 05 09 is possible after pressing Set Clock actual system date changing is possible after pressing setting is possible after pressing Date 06 05 1999 PR 1713 rel 1 10 45 4 5 2 Serial Ports Configuration of serial interfaces After selecting Serial Ports the menu Setup serial for _selection of a serial interface is opened PecupEseruo Order is dependent of configuration Builtin RS 232 51011 RS 485 slot1 Ports VBniltin RS232 slot2 RS485 slot2 RS232 slot3 RS485 slot3 RS232 only existing interfaces are displayed _The following specifications can be provided for each selected serial interface Setup Builtin e
105. ire connection possible Load cell supply U 6 V for Imax 160 mA Load cell supply circuit 12V DC for max 8 load cells each with 600 Q for 4 load cells each with 350 Max load gt 75 9 6 1 4 Safe condition The software is monitored by a watchdog timer In case of error reset occurs whereby all digital and analog outputs are reset to a defined condition The load cell input is checked if the error leads to a measurement value which does not make sense No failure checking of digital inputs and outputs or of analog output is made 94 rel 1 10 PR 1713 6 1 5 Certificate of type approval For the System Weighing Controller PR1713 certificate of type approval no D99 09 039 by Physikalische Technische Bundesanstalt PTB for non automatic weighing machines EN45501 is available i e the indicator meets the prerequisites for approval by the local authorities in all countries of the European community For weights amp measures application the W amp M mode have to be Enabled see 4 4 3 PIB Physikalisch Technische Bundesanstalt Braunschweig und Berlin EG Bauartzulassung EC type approval certificate Zulassungsinhaber GWT GLOBAL Weighing Technologies GmbH Issued to Meiendorfer Str 205 22145 Hamburg Bundesrepublik Deutschland Rechtsbezug 13 des Gesetzes ber das und Eichwesen verification act Inaccordanee witty vom dated 23 Marz 1992 BGBI 1 S 711 in Verbindung mit Richtlinie in connectio
106. ired Prepare PR1713 Open menu Setup select submenu Reboot select menu item Reboot wait for message Reboot done Then select menu item Flash select the serial port St reem Builtin Slot3 RS2324 Slot3 RS485 After the softkey Flash in bootmenu select the serial port which is to be used for downloading the program Possible error message pa not possible with switch CAL closed CAL Jumper closed If the serial port Builtin is occupied the interface can be selected with and only available if a serial I O card PR1713 04 is inserted Prepare the PC Flashlt 32 must be started now on the connected PC Select firmware file from the list in the window press flash button wait for message completed During software loading various status messages are displayed Lashcode loaded Erasing euo CESTo ank test passed lashing 812400 est Checksum F B B F T Subsequently the boot menu with the following status line is displayed again Flash complete After that initialize PR1713 with Cold Flash erases the databanks of PR1713 therefore Erase is not necessary before Flash to erase internal databanks If Erase was started the safety question has to be answered before erase is executed after that Reboot PR 1713 rel 1 10 39 4 4 Calibration weighingpoint parameters Standard calibration of the analog part by weights and m
107. is shown in the mask header Configuration of WP B HOsout E Q PR1713 00 Rel XX XXX XX Configuration of WP MIG XOX OOK OOO Fullscale 1000kg Stepwidth 1 Overload Od Minwgt 0d Scale lkg lent Update Time 6 50 msec Input address 32 Exit configuration Quit configuration Enter Input address 32 E to exit 27 address must be gt 32 and lt 255 Select the individual parameters by entry of the relevant letter F s d value F Fullscale The full scale value determines the maximum weight to be measured Permissible entries cover the overall weight range between 0 1 00 and 99999 00 in g kg t or Ib The value must be divisible by 100 and must have max 3 digits behind the decimal point If the entry does not meet these criteria the following error message is displayed Illegal Fullscale Stepwidth divisions S Stepwidth Stepwidths 1 2 5 10 20 50 With all other entries the following error message is displayed Illegal Stepwidth 84 rel 1 10 PR 1713 Maximum permissible overload O Overload Entry in d permissible range 0 d to 9999999 d Min weight limit for print out M Minwgt Entry in d permissible range 0 d to 9999999 d Weight value pulse C Scale Entry is in two steps 1 Entry of weight value per pulse s Enter weight Ikg E to Exit Old value default setting is displayed in square b
108. ith on or off Specification is via configuration but can also be changed via communication Attention PR1713 does not check if the input fits into the scale range wP A limit 1 on weighing point A limit value 1 0 kg switch on point A limit 1 off weighing point A limit value 1 0 kg switch off point A limit 2 on weighing point A limit value 2 0 kg switch on point A limit 2 off weighing point A limit value 2 0 switch off point B limit 1 on weighing point B limit value 1 0 kg switch on point B limit 1 off weighing point B limit value 1 0 kg switch off point wP B limit 2 on weighing point B limit value 2 0 kg switch on point wP B limit 2 off weighing point B limit value 2 0 switch off point Limit values Example for switch on and off values hysteresis For a min limit value 2 of 100 kg and a max limit value 1 of 2900 kg The hysteresis is 10 kg with the two limit values The output for min limit value 2 must not be activated when exceeding and the output for max limit value 1 must not be activated when exceeding l e with power failure inactive outputs the limit values are exceeded safety status e g fill checking via the limit values Via output configuration limit values 1 or 2 are allocated to the relevant output inclu
109. keyboard Both keyboards are equivalent They can be used alternatively and generate equal ASCII codes Alternatively entries from a serial terminal are possible Standard connector pin allocation Connection for a german PC keyboard 1 KBD Clock The LEDs of the PC AT keyboard are not 2 KBD Data controlled The max permissible current 3 nc consumption of the PC AT keyboard is 50 mA at 4 GND 5 V Overload is prevented by a multifuse element 5 5V 3 3 3 RS 232 Builtin interface PR1713 is equipped with a standard RS 232 interface which is accessible externally as Builtin from outside When a terminal or PC with terminal program is connected the interface can be used for calibration and configuration of the instrument The interface can be used freely and can be configured e g for data transmission to a supervisory system or to a remote display The remote display string is output continuously If the RS 232 Builtin interface is used for configuration wire it as shown below RS 232 Builtin Terminal wae RTS 1 XON XOFF protocol 25 pol sub D Builtin a Tx 2 2 Tx m s Te w crsa GND 5 7 GND The Builtin 2 PC terminal strip is RS 232 Builtin located directly Software WIN Terminal on the RTS 1 XON XOFF protocol 9 pol sub D connecting Tx 2 2 Rx board in the Rx 3 3 Tx housing CTS 4 Access to the built in RS 232 GND 5 i GND interface is after opening xL B the housing 7
110. lectromagnetic compatibility 98 rel 1 10 PR 1713 6 4 Mechanical data 6 4 1 Construction type All metal housing of stainless steel Protection class IP 65 6 4 2 Dimensions Housing Dimensions Width 288 mm Height 144 mm Depth 130 mm 135 mm incl blind plugs 6 4 3 Connections Via PG glands Plug in screw terminals in the unit 6 4 4 Accessories Installation manual operating manual label for weighing range 2 cable ties screw driver metal PG glands EMC glands 2x PG 13 5 1x PG 9 6 4 5 Weight Net weight 3 5 kg Shipping weight 5 kg PR 1713 rel 1 10 99 6 5 Options 6 5 1 Analog output 16 bit resolution galvanically isolated Output Gross net weight or fixed value updating coupled with the measuring time Range 0 4 mA 20 Load 0 500 Q Resolution 16 bits Linearity error 23 C 0 012 96 Overall error 0 15 96 Overall temperature error 50 ppm K 6 5 2 Digital inputs 4 Inputs galvanically isolated via opto coupler passive mode external supply no common potential Input signal for Low 0 5 V or open input Input signal for High active status 10 31V Input current for High lt 8mAat24 V lt 4 mA at 12 V Min control time gt 100 msec 6 5 3 Digital outputs 4 outputs galvanically isolated for PR1713 12 via opto coupler NPN transistors open collector for PR1713 15 via relais contacts permissable output load with PR1713 12 PR1713 15 Max
111. me Set enter name and calibrate with sample unload load Set Show Print Show display setup for the number Print single or all PR 1713 rel 1 10 53 5 COMMISSIONING WITH TERMINAL One of the serial interfaces of PR1713 e g RS 232 Builtin can be defined for the system console The system console can be used for calibration configuration and operation of PR1713 5 1 System console connecting menu structure A terminal or a PC can be used as a system console Conection to the buitin interface see 3 3 3 RS 232 Builtin interface an other interface is used in the same way To use the terminal as operator device the following set up has to be made e Software Parameters Operator Device on select the intended interface 4 5 3 13 e Setup Serial 4 5 2 for the interface Protocol X ON Device ANSI Echo Disabled setting of interface as the terminal e g 9600 Bd 8 bits 1 stop no parity 5 1 1 Connecting PR1713 PC The PC is connected with a directly connected cable Rx Tx not crossed to the configured 4 5 3 13 built in RS 232 interface 5 1 2 Terminal program The terminal emulation program Hyper Terminal provided by Windows is in the Accessories If this program is not available proceed analogously with a comparable program Terminal programs of various manufacturers can be used for commissioning on many operating systems provided that they behave like a VT100 ANSI terminal and can be adjusted to t
112. n The weight values are determined by an external weighing point module e g PR1710 read in by a IEC 1131 program and stored in the relevant SPM address e Reading in and scaling of the measuring signal An analog or digital measuring signal analogous to the weight value is read in by a IEC 1131 program converted according to a scale factor and stored in the relevant SPM address The value is available for evaluation by the customer specific IEC 1131 program The scale factor can be entered in the configuration mask Entry is as parameter Weight pulse scale i e weight per count PR 1713 rel 1 10 83 Volumetric weight measurement Conversion into a weight value and weight pulse counting must be programmed in a customized IEC 1131 program The specific weight pulse scale can be entered in the configuration mask i e it is available for evaluation by the customized IEC 1131 program General technical data External weighing point Weight input configurable Memory location M marker area Size D double word per weighing point permitted input address range MD32 MD255 Permitted batch modes as standard weighing point Batching cycle 50 msec Power failure behavior Batching sequence provided as standard Save the definition data in the PR1713 RAM Data must be re entered after cold starting Entry of configuration parameters Entry is via the following mask Weighing point display The weighing point
113. n other parameters are required After parameter entry PR1713 makes a warm start in order to initialize the PR1721 module in the unit Interbus S The value 7 50 at IBS cycle indicates the actualization interval Calculate the value by Scale mode Enabled activates the standard interface between scale and fieldbus 5 2 7 Entry of user defined units PR1713 00 Rel XX XX X XX XX XXXX XX XX Configuration MO 1320682116 U Set units P Print all configuration data E Exit Enter new units ulu2u3u4u5u6u7u8 For use by PROLOC firmware functions MAKE WEIGHT and SET WEIGHT UNIT 8 different units can be defined Each unit is composed of 2 characters Entry modification of the 8 user defined units e Press key U e A string 16 characters of the 8 actual units 2 characters is displayed Enter new units ulu2u3udu5u6u7u6 The cursor is behind the 16 character e Move cursor with arrow keys delete characters with the backspace key lt line editor e Entry of required characters units e the Enter key If the entry is correct the line is removed from the display If the entry is faulty the following message must be 16 characters lbcmdm and the characters entered so far are displayed 5 2 8 Printing all configuration data All parameters are printed out via the serial interface configured for the printer previously PR 1713 rel 1 10 63 5 3 Weighing point m
114. n by mV V Enter deadload mV V Q to quit S to skip Enter deadload mV V enter deadload in mV V Q to Quit press Enter 1 and quit without doing anything S to Skip press Enter 1 and skip the tare entry 2 Enter the deadload in mV V Enter the deadload with comma or point Complete by pressing the Enter key 1 e PH1713 evaluates the data Now the following command line is displayed in the weighing point calibration mask Setting deadloads system saves the data subsequently Setting deadloads Status OK message is displayed during approx 2 s e weight display does not change 3 The following command line is displayed in the calibration mask Span Calibration by mV V Enter span mV V E to exit _ Enter span mV V Enter the span in mV V E to Exit Enter key 4 no entry terminate calibration 4 Enter the span in mV V Enter the span with comma or point Finish the entry by pressing the enter key 1 e PR1713 evaluates the data Now the following command line is displayed in the weighing point calibration mask Setting span the system saves the data subsequently Setting span Status OK the message is displayed during approx 2 s Calculating test the system calculates the test value PR 1713 rel 1 10 79 Calculating test Status OK e The new gross weight is displayed 0027 kg Subsequently the standard command line is displayed Keypad Select item with
115. n with council directive 90 384 EWG geandert durch amended by 93 68 EWG Bauart Nichtselbstt tige elektromechanische Waage mit oder ohne In respect of Hebelwerk Nonautomatic electromechanical weighing instrument with or without leverworks Max 1kg 500t ap n lt 5000 Type Type PR1713 Zulassungsnummer D99 09 039 Approval number G ltig bis 11 11 2009 Valid until Anzahl der Seiten 7 Number of pages Gesch ftszeichen 1 14 99052555 Reference No Benannte Stelle 0102 Notified Body Im Auftrag Braunschweig 12 11 1999 By order es Link Siegel Seal Die Hauptmerkmale Zulassungsbedingungen und Auflagen sind in der Anlage enthalten die Bestandteil der EG Bauartzulassung ist Hinweise und eine Rechtsbehelfsbelehrung befinden sich auf der ersten Seite der Anlage The principal characteristics approval conditions and special conditions if any are set out in the Annex which forms an integral part of the EC type approval certificate For notes and information on legal remedies see first page of the Annex PR 1713 rel 1 10 95 6 1 6 Location of seals Physikalisch Technische Bundesanstalt PIB Anlage zur EG Bauartzulassung Annex to EC type approval certificate vom 12 11 1999 Zulassungsnummer D99 09 039 Seite 7 von 7 Seiten dated 12 11 1999 Approval number D99 09 039 7 of 7 pages PR 1713 00 kg pr BCDEFGHUKLMNOPORSTUVWXYZ abcdefghiikimoparstuvwxyzi234
116. nd X to set fixed span P to print The system offers the following replies Unload and hit 0 unload scale set the zero Load and hit Return load the scale set the span E to End finish calibration X to set fixed span set the fixed span P to print print out the calibration parameters 4 Set only the zero finish calibration E to End Press key E Calculating test system calculates the test value Calculating test Status OK Now the following command line is displayed Keypad Select item with cursor up down left right Change with Return to FiXed Set fullscale Calibrate by Weight or Millivolts E Exit calibration Subsequent zero correction is finished The data must be saved proceed as described in points 9 and 10 of the Weighing point calibration procedure 5 6 7 Weighing point calibration without weights If the scale to be calibrated is not subject to the calibration law and if calibration with weights is not possible or not required for reasons of accuracy weighing point calibration without weights is possible As a prerequisite however the load cell sensitivity if possible the sensitivity of each load cell must be known This information can be used to calculate the span e Calculation of the load cell sensitivity If the sensitivity C of the individual load cells 1 to n is different the mean load cell sensitivity Cav is calculated as follows Ci Cs Ca Caw Raavr
117. nd set the zero Load and hit Return load the scale and determine the span E to End finish calibration X to set fixed span set the fixed span P to print print out the calibration parameters Calibrate the weighing point Apply the calibration weight if possible full scale e the Enter key 1 e The following command line is displayed the weighing point calibration mask Enter calibration point 6000kg to exit e The full scale is proposed as calibration weight e Enter the calibration weight Weight value with comma or point as required no or one or several spaces dimension g kg or t complete by pressing the Enter key 1 dimension g kg or t press the enter key to complete the entry e Possible error messages Setting weight Bad Weight e g dimension is missing Setting weight Status Above Scale weight value too high Setting weight Status Above phymax input voltage 36 mV The command line as shown in point 3 is displayed Unload Load Calibration by weight Unload and hit O or S to skip E to end X to set fixed span P to print Calibration step 2 to n repeat weighing point calibration 1 to n 1 1 Replace calibration weight by substitute weight Load and hit Return 2 Press the Enter key and return to point 4 Caution calibration weight enter total substitute weights calibration weight e of error repeat calibration step as desc
118. nded exclusively for application in weighing and batching installations and is particularly suitable for tank and hopper weighing weighbridges platform scales crane weighing batching systems and as a weight indicator in intelligent control systems Product operation commissioning and maintenance must be done by well trained and qualified persons who knows of the risks and avoid them or take measures to protect themselves The instrument is state of the art No warranty is taken that the product is free of errors especially with reference to the software and hardware required for operation and supplied by third parties The manufacturer does not take any liability for damage caused by incorrect use of this product Using this product implies recognition of the above mentioned regulations 1 2 Initial inspection Check the contents of the consignment for completeness and note whether any damage has occurred during transport If the content is incomplete or damaged a claim must be filed with the carrier immediately and the GWT GLOBAL Weighing sales or service organization must be informed to permit repair or replacement of the unit 1 3 Before commissioning Visual inspection Before commissioning after storage and transport the instrument must be inspected visually to preclude mechanical damage 1 3 1 Installation PR1713 has an installation bracket with holes in different distances and can be mounted adjustable between rubber disks by k
119. nfiguration data Printing out is done via the serial interface configured for the printer 92 rel 1 10 PR 1713 5 9 PROLOC operating level The operating level is required for testing user specific IEC 1131 programs Calling up PROLOC operating level Proloc is from the Main Command Level by pressing key P e Anempty screen with prompt character is displayed The cursor is positioned beside this character The operating level expects the entry of a command e By entry of command Help complete by pressing the Enter key a short form description of possible commands is displayed Subsequently the system waits again for entry of a command Datei Bearbeiten help IR FB FU PG OPER PLC REC V HOW TASK HOW TABLES HOW TOPCPU IT SET x ILL OPER PLC RI Einstellungen Telefon bertragung Hilfe Terminal 1713CONS TRM OPER PLC R EC lt dbase_name gt EC lt 1 2 3 4 ALL gt 2 ESTART lt OP ELETE dba progra gt se_name gt m_name gt NOI ER PLC 1 2 3 4 ALL BRI STATUS TIME CONT EAK Leaving the PROLOC operating level e By entry of command Exit complete by pressing the Enter key J return is to the Main Command Level PR 1713 rel 1 10 93 6 TECHNICAL DATA The characteristic data are
120. nnecting the supply voltage The firm power connection must be protected with a fuse Additionally an interruption safely of both phases of the supply voltage must be possible e g by means of a switch or a power connector 1 3 6 1 Power supply PR1713 01 The device PR 1713 01 is prepared for operation with 24V AC DC supply voltage use mains screw L and N of terminal block connect 24 V PR 1713 rel 1 10 3 Changes in the operating manual for PR 1713 01 The information about mains supply voltage is changed to 24 V AC DC in chapters 1 3 6 A 16 2 5 1 4 Repair and maintenance Repairs are subject to checking and can be carried out only in the factory at GLOBAL Weighing Technologies GmbH Hamburg In case of defect or functional trouble please contact your GLOBAL Weighing Technologies organization for repair When returning the instrument for repair an exact and complete fault description must be supplied Maintenance work may be carried out only by a trained technician aware of the involved hazards whereby the relevant precautions must be taken 1 4 1 Failure and excessive stress If the instrument is suspected of being unsafe shut it down and protect it against accidental operation This is the case when the unit e is physically damaged e does not function any more e is stressed beyond the tolerable limits e g during storage transport
121. ns sss n nnns 53 SLA Connecting PRI713 PC aa ean ene eve dede seva abe gere aeg 53 5 1 2 Terminal DrogTam ute eti ree ie en 53 5 1 3 Main Command Level menu structure eese renes nnn 54 5 14 General operating NOLES etd tee re hd ped te he dip erat de te deste e ea sess 56 5 2 CONFIGURATION ERE 57 5 2 Net dale sti SEMI 57 DDD SeUTUme io E UE 58 5 2 3 Serial interface configurations sd e i t e t rette eet ee etre ees 58 5 2 4 Entry of the software licence number eese eene nennen nennen nennt 60 3 2 5 Entry of software parameters one ttesce t dee ege dtd eee aee 61 5 2 6 Fieldbus parameter sedi ise ege deii dete deret eig e deae etev sie eo ege deese te edendo 62 5 2 7 Entry of user defined units x da tiet tefte ede i edis aret 62 5 2 8 Printing all configuration data esee 62 2 3 WEIGHING POINT MASK eiat n Gees Deck cet en iere den i ette este det emi o RE ERE 63 5 4 WEIGHING POINT PARAMETERS STORING SAVING PROTECTING eese nnne nnns nnns nnns nsns nsns 64 5L I Access protection CAL SWItCh uiti te t de tee tdi ette 64 5 4 2 Saving the weighing point parameters in EAROM essen eene rennen 66 5 4 3 Sav
122. nterfaces are given logic names in the order of allocation found in the slots In this example the only card is always detected as TTY1 and TTY2 whereby TTY1 is the RS 485 and TTY is the RS 232 interface If 2 or 3 PR1713 04 cards are fitted logic names from TTY3 do also exist starting with slot 1 Output in case of success PR1713 00 Rel SEK 5050 50 ORO SOR SOK 8 ROR Test PR1713 04 Slot Number 1 Mo XXXX 09 31 51 TP Es Send with RTS ON passed Send with RTS OFF passed nodata Send with RTS ON passed TIYX2 TXD RxD passed RTS CTS passed DTR DCD RI passed Output in case of error e g PR1713 00 Rel OOK IK Test PR1713 04 Slot Number 1 Mo 09 31 51 TTY1 Send with RTS ON failed nodata Send with RTS OFF passed nodata Send with RTS ON failed nodata TTY2 TxD RxD failed nodata RTS CTS pattern failed 1111 0010 DTR DCD RI pattern failed 1111 1100 PR 1713 rel 1 10 89 5 8 3 2 Analog output module testing The test can be executed for PR1713 06 and PR1713 07 PR1713 00 Rel Test PR1713 06 Current Analog Output Va Enter decimal output 0 100 Set Output D Decimal Input Format 0 H Hexadecimal Input Form E Exit KRE ROK GN BOK ORK ROK SSK Slot Number 2 lue Dec 075 Qe 6 100 for Output Value
123. nting a cable e Remove the screw cap e Slide cap and plastic cone over the cable e Fold the cable screening over the sleeve and the lower part of the plastic cone e Take the cable through the gland e Connect the cable conductors e Tighten the PG gland 1 Edge recess in the PG gland 2 The cable screening is pressed against the recess by the plastic cone 3 Plastic cone 4 Screw cap 2 12 rel 1 10 PR 1713 3 3 On the connecting board 3 3 1 Load cell cable cable junction box PR 6130 PR 1713 Terminal terminal 3 terminal 4 terminal 5 terminal 6 terminal 2 terminal 1 terminal 7 Recommendation lay in steel tubes connected to earth potential min 1 m distance to power cables Load cell supply circuit Load cell circuit resistance load 75 Ohm e g 8 load cells each with 600 Ohm firmly adjusted to 12 V protected by a 250 mA slow blowing fuse see 1 4 3 Connection of one load cell in 4 wire technology e Provide jumpers from 6 V to Sense and from 6 V to Sense Connection of 4 up to 8 load cells in 6 wire technology e via cable junction box PR6130 with cable PR6135 terminal block LC connection Uineas U meas 6 V Ux Usense Usense Ki 6 V Ue GND NOOR WD PR 1713 rel 1 10 13 3 3 2 External PC AT keyboard PR1713 is equipped with an alphanumeric front panel keyboard and a connection for a german PC
124. nurled head screws to the detachable installation bracket The stainless steel housing of the instrument fulfills IP65 The unit can be mounted in any position however the PG glands should not point upwards water Before commissioning the instrument all unused instrument apertures must be closed with blind plugs For cooling the instrument the air circulation must not be hampered Heat influences e g direct sun radiation must be avoided The environmental conditions specified in the technical data must be taken into account The unit is suitable for Table top installation The unit stands on the detachable installation bracket Wall mounting Mount installation bracket on the wall The unit is held by knurled head screws Installation in With mounting brackets optional mounting kit PR1713 91 can be ordered control cabinets separately 2 rel 1 10 PR 1713 1 3 2 Electrostatically sensitive components This instrument contains electrostatically sensitive components Therefore potential compensation must be provided when working at the open instrument antistatic protection 1 3 3 Opening the instrument CAUTION DANGER TO LIFE Working at the switched on unit may be dangerous to life Disconnect the instrument from the supply voltage When removing covers or parts by means of tools live parts or terminals may be exposed Capacitors in the unit may still be charged also after disconnecting the unit from all volta
125. o lt 0 gt is displayed in front of the weight Setting or deleting the tare memory is done with keys I or O V O Tare In Out Press key to carry out the analog test Test Test value and reply line Toggle Testmode Status OK instead of the weight is displayed Pressing key once more displays the previous value again Pressing key P Print prints out the weight values on configured printer Description of the weighing point calibration mask Calling up mask Additional WP s Calling up is done by pressing key A If a production is running this call is disabled message Production is active no configuration possible 64 rel 1 10 PR 1713 5 4 Weighing point parameters storing saving protecting This chapter describes how to store save and protect the weighing point parameters The individual weighing point parameters entry weighing point configuration and weighing point calibration are described in the two following sub sections 5 4 1 Access protection CAL switch The weighing point parameters are protected against unauthorized accidental access by the CAL switch S I L switch in the analog part calibration protection Evaluation of the switch position is when calling up mask Calibration CAL switch in open position access permitted e When calling up mask Calibration the access is permitted i e the weighing point can be configured and calibrated In addition to the actual weighing point param
126. o set fixed span P to print The system offers the following replies Unload and hit 0 unload the scale and set the zero Load and hit Return load the scale and set the span E to End finish the calibration X to set fixed span set the fixed span P to print print out the calibration parameters Calibrating the weighing point 1 Place the calibration weights on the scale if possible full scale 2 Press enter key 1 The following line is displayed in the weighing point calibration mask Enter calibration point 6000kg E to exit The full scale is proposed as calibration weight 3 Enter the calibration weight Weight value with comma or point as applicable no or one or several spaces dimension g kg or t Press the enter key to complete The following command line is displayed in the weighing point calibration mask Enter calibration point 6000kg E to exit 4000 kg If the values are within the permitted range the following message is displayed after a few seconds Setting unit Status OK Setting weight Status OK Message is displayed during approx 2 sec Possible error messages Setting weight Bad Weight e g dimension missing Setting weight Status Above Scale specified weight to high Setting weight Status Above phymax input voltage 36 mV The command line as shown in point 3 is displayed Unload Load Calibration by weight Unload and hit or to skip E to end X to set
127. ocal printer Function key disabling Several PR1713 function keys can be disabled for defined applications tare untare and set zero Enabled Disabled Enabling disabling is always done for all PR1713 weighing points Allow quit in main level may be set to on or off Allow quit in main level should be on only if necessary l e if serial interface SERIAL I O 1 is used also for other purposes by PROLOC programs except for the system console terminal terminal emulation Stop Quit After pressing keys Stop and Quit for 7sec or 5sec during operation the boot menu is displayed Reset switched off disabled Inbatch mode on Unit is used with InBatch off Unit at PR1740 or stand alone 62 rel 1 10 PR 1713 5 2 6 Fieldbus parameter Calling up mask Set fieldbus configuration is from sub menu Configuration by pressing key F Rel XOXoXOXaX SOR Configuration for the fieldbus unit Fieldbus Configuration PR1721 xx PR1721 protocol Profibus DP None Interbus S Profibus DP Devicenet IBS cycle P dde 1 50 Profibus DP slave adress 1 1 126 DeviceNet baudrate 500k 256k 125k DeviceNet node adress o 1 62 Scale mode Enabled Disabled Enabled Select a field by means of cursor keys 7 and J Changing parameters by the keys If the PR1721 module is inserted in the unit values are selectable Dependent of selectio
128. ocedure sequence Weighing point calibration or recalibration is as follows 1 Load default values with X if required 2 Allow the unit to warm up min 60 minutes 72 rel 1 10 PR 1713 3 CAL switch open weighing point parameter access enabled 4 Call up the calibration mask of the relevant weighing point 5 Enter the weighing point configuration parameters Check change default parameter Filter e With subsequent modification of this parameter recalibration is recommendable All other weighing point parameters can also be changed subsequently 6 Determine the full scale Fullscale 7 Select the calibration mode Select item with cursor up down left right Change with Return to FiXed set Fullscale Calibrate by Weight or Millivolts E Exit calibration Weighing point calibration with weights Calibrate by Weight Press key W Weighing point calibration without weights or Millivolts Press key M 8 Realize weighing point calibration 9 Store the weighing point parameters temporarily or save them in EAROM 10 CAL switch closed weighing point parameters protected The internal CAL switch for the built in WP is open and normally remains open 5 6 6 Weighing point calibration with weights The two methods of weighing point calibration with weights are e calibration weight corresponding roughly to or smaller than the full scale can be placed on the scale calibration
129. omatic zero tracking with zero drift 0 500 00 d Step width for automatic zero tracking 0 10 00 d Operating mode for multirange scale off on Max permissible overload value above full scale 0 9999999 d Don t print below 9 W amp M lower weight limit for print out 0 9999999 d Form of printing may be changed in the application program Measuret ime Standstill time Zerotrack time Tare timeout Standstill range Zeroset range Zerotrack range Zerotrack step Multirange mode o o Overload Multirange limit 14 Multirange scale first change over limit 0 9999999 d 0 off Multirange limit 24 second change over limit 0 9999999 0 only 2 ranges 4 4 3 1 Multirange scale The multirange function is controlled by three parameters in the calibration see above With Multirange mode on the scale has three ranges with different resolution the change over limits Multirange limit 1 and Multirange limit 2 represents the range border If the gross weight has more d as the relevant change over limit the next wider stepwidth is used 1 gt 2 gt 5 gt 10 gt 20 gt 50 If the gross weight is lt 0 25 d of the lowest range the scale in standstill and untared condition the scale will be switched back to the lowest range On the display the ranges are marked by quotes or
130. or the calibration weight value The input voltage or the input voltage calculated for the f s d is gt SKE the entered step width is not correct SKE not divisible by stepwidth incompatible stepwidth after calibration a new f s d was entered again which nevertheless is below the initial calibration point f s d Caution subsequent entry of a larger scale is permissible without recalibration These messages are only generated with different dimensions To generate an error message the scale must be incalculable e g f s d 1000 kg entered calibration weight 1g should be 1 t which would be accepted The actual or the calculated input voltage is gt 36 mV The measurement signal for the specified scale is too small EAROM error Cancel by pressing key Q PR 1713 rel 1 10 81 5 7 Additional weighing points In addition to the weighing point module in PR1713 00 weighing point A a weighing point B can be defined e 1720 00 via Interbus S IBS UART or e weighing point on weighing point B As PR1713 cannot display the weight value on the front panel a remote display device for weighing point B may be installed supported with firmware rel 1 1 These additional weighing points are defined in mask Additional weighing configuration This mask is called up from mask Weighingpoint by pressing key A Moreover this mask provides a survey of the additional weighing
131. ore starting any work read section 1 Safety hints electrical protection class and follow all hints Further procedure Check the consignment unpack all parts pertaining to the project Safety inspection damages Ensure that the installation is correct and complete including cables e g power cable power connection with fuse load cells cable junction box data cable console cabinet etc The instructions for installation of the unit related to application safety ventilation sealing external effects must be followed Opening the instrument Check the supply voltage If necessary turn to voltage selector into the correct position If necessary mount the options plug in cards memory extension Fit the jumper for internal battery Connect the cable from the cable junction box or load cell If necessary connect further data cables Connect the power cable Check the installation and connect the unit 3 1 Mechanical preparation A table top unit requires a flat stable surface With wall mounting the installation bracket must be mounted on the wall With cabinet or panel mounting the housing must be provided with a cut out Keep all parts technical documents and required tools at hand Take the cable to the place of installation and mount it e g by means of cable ties Remove the insulation from the cable ends and keep the strands short 3 2 Hardware construction Builtin TH 10 rel 1 10 PR 1713 Th
132. point definition Customer specific weighing point user Not defined none PR1713 00 Rel XX XX XXXX XX XX YwSiClasliacgjioOsinc COimcsleibiecic lem JMo sooox 098351 55 B user U Userdefined P PR1720 O Off E Exit e Weighing point selection Select the weighing point using the two cursor keys T and J The actually selected weighing point is highlighted by inverse display e Definition of additional weighing points Dependent of selected weighing point the permitted definitions are displayed Definition is by entry of the relevant letter For entry of the required parameters the relevant mask is displayed subsequently Customer specific weighing point U Userdefined Additional external weighing point P PR1720 If the weighing point was already defined the following prompts may be displayed e Deleting a weighing point Delete the weighing point O Off Pressing key O deletes a weighing point The following prompt is displayed Switch WP off sure Press Y or N Return to the weighing point mask is with E Exit configuration 82 rel 1 10 PR 1713 5 7 1 PR1720 as second WP The weight is read directly from the PR1720 00 By means of a customized IEC 1131 program the weight value read out with GET WEIGHT can be made available on the alphanumeric display of PR1713 e Entry of the configuration parameters is via the following mask The weighing point is indicate
133. rackets 1kg Cancel the entry E Enter key E to Exit Error message with faulty weight entry Bad weight Units scale fullscale do not match Unit does not match Permitted weight entries 7 digits with decimal point The entry must be completed with the correct unit e g kg The units of fullscale and scale must be equal Checking is done when leaving this mask See below E Exit configuration If the entry is accepted a prompt for entry of the number of pulses is displayed 2 Entry of the number of pulses Enter counts 1 E to Exit The old value default setting is displayed in square brackets 1 Cancel the entry E Enter key E to Exit Error message after faulty entry of the number of pulses Bad number Cycle time for weight display T Update time Entry is in n 50 msec With an entry of e g 6 display of the weight values is updated at intervals of 300 msec 6 50 msec Permitted range 2 20 Error message with faulty cycle time entry Bad number Finish configuration and save values E Exit configuration If different weight values for fullscale and scale were entered the following error message is displayed Fullscale and Scale must have same unit The error must be corrected Subsequently the mask can be left Leave the configuration without changing values Q Quit configuration If parameters were changed the following prompt is displayed Abandon changes sure Press Y or N
134. ribed in point 4 1 Apply the calibration weights Load and hit Return 2 Press the Enter key 4 see 4 e Set fixed span X to set fixed span 76 rel 1 10 PR 1713 If the calibration cannot be finished correctly for any reason press key X To avoid operator errors a prompt is displayed which must be replied with Yes No Y N Y means restart step by step calibration The system executes the command Subsequently the command line shown in point 5 is displayed again Print out actual weight P to Print Press key P The system executes the command Subsequently the command line as shown in point 5 is displayed again e Setthe zero Unload and hit O If necessary zero setting as described in point 2 can be repeated e Finish calibration E to End Press key E Calculating test System calculates the test value Calculating test Status OK Subsequently the standard command line is displayed Keypad Select item with cursor up down left right Change with Return to FiXed Set Fullscale Calibrate by Weight or Millivolts E Exit calibration Calibration is finished The data must be saved Proceed as described in points 9 and 10 of the Weighing point calibration procedure 5 6 6 3 Subsequent zero correction Description If the hopper weight changes e g due to loss tare reduction or slag tare increase by an amount which is higher than the zero set range the automatic zero trackin
135. rmissible output rating is for PR1713 15 max switching voltage 32V max switching current 1A The jumper J102 J105 J108 J111 are set to A upon delivery closing contact To change to an opening contact open A and close B by soldering Bis 12110 15 7109 J111 5 BA Br 113107 The jumper J100 J101 J103 J104 J106 J107 J109 J110 are intended for special assembly may not be altered Br 11104 AU J103 J105 Br 117101 AU J100 J102 Pin allocation of options connectors in the Eom PR1713 00 unit see previous page 22 rel 1 10 PR 1713 3 3 8 PR1713 08 BCD output This option card for PR1713 is preferably used in the slot 3 on right side installation see page 10 because otherwise plugs for other cards are blocked The card can be used only in connection with an application program written in IEC1131 Binary data needs to be decoded by the application program for a BCD output The weight values gross net tare are stored in binary form in the SPM e Accessory 28 pole connection cable with plugs 20 pole and 8 pole at one side Plug and connection cable Output bit Q decade bit value pin bit color pin bit color 1 Q01 Sw 2 Q02 Br Color table 3 Q04 Rt 4 Q08 Or 5 Q11 Ge 6 12 Gn Sw black 7 Q14 BI 8 Q18 Vio Br bruin 9 Q21 Gr 10 Q22 Ws Rt red 11 Q24 Ws sw 12 Q28 Ws br Or orange 13 Q31 Ws rt 14 Q32 Ws or Ge yellow 15 Q34 Ws ge 16 Q38 Ws gn Gn green
136. rotected E Exit display Cal Jumper closed A note that the CAL switch is closed is displayed Cal Jumper closed l e the data can be displayed without changing them The mask can be left by pressing key E E Exit display e Command line access permitted Keypad Select item with cursor up down left right Change with Return to FiXed Set Fullscale Calibrate by Weight or Millivolts E Exit calibration PR 1713 rel 1 10 67 1 The commands for entry of the weighing point parameters are displayed in the first line Select item with cursor up down eft right Change with See items Select item and Enter change parameters 2 The second line refers to weighing point calibration 3 The last line contains the command for leaving the mask E Exit calibration See previous sub section Exit calibration ltem selection Item selection is with the four cursor keys lt gt T and Select item with cursor up down left right The selected item is displayed inversely Parameter entry changing The entry change is dependent of the item The two types of entry change are e Selection item selection of predefined parameters is with keys Selection fields are Filter Testmode and Stepwidth All other fields are normal input items Nevertheless they can be changed with keys and e Input item entry of required parameter value During
137. s the maximum weight which can be measured Permissible entries are within the limits of the full scale value overall weight range within 0 1 00 and 99999 00 in g kg t or Ib The value must be divisible by the step width and must have max 3 digits behind the decimal point Calibration weight Calipoint This is the value of the calibration weight weighing point calibration with weights or the theoretical calibration weight weighing point calibration without weights Deadload Deadload The value of the scale after discharge the scale deadload The input voltage equivalent to this weight value is displayed stored in mV V Span Span e The span is determined by calibration by means of weights or e must be entered during calibration without weights The span indicates the equivalent input voltage in mV V related to the scale f s d full scale full scale load cell sensitivity C mV V span mV V load cell capacity sum of all load cells Span in mV V Full scale as a weight value Load cell sensitivity C mV V Load cell capacity sum of all load cells as a weight value Resolution c d Resolution c d The resolution c d indicates the number of internal counts result of analog conversion related to the stepwidth 2 smallest division d by which the display value can change This value should be as high a possible related to 1 Resolution cd c Resolution cd c The resolution cd d is the inverse value of resol
138. shlt 32 is included in the BIOS otherwise PR1713 needs to be repaired In these cases a warm start is not possible Reboot done Cold A Brase M Flash Possible operation Cold A cold start is made Messages Check firmware The firmware checksum is tested Firmware coldstart cold start is carried out Erase Awarm start is made if possible Messages Check firmware The firmware checksum is tested Firmware warmstart A warm start is made Flash Loading of new software is prepared loading of new software 4 3 2 1 _Further options are displayed with More key Reboot done Test V SAD DBGR Test Various hardware tests are called up The middle and the right softkey must not be used further internal test functions which can lead to undefined behavior of the unit are started 38 rel 1 10 PR 1713 4 3 2 1 Loading new firmware The PR1713 includes firmware with application for standard use A firmware without application may be used for projects You need Flashlt 32 Rel 2 04 if you want to replace the application PLC with your own PLC project Firmware and PLC program can be taken from the Complementary SW Tool box CD or from our internet address Update the BIOS only if requested by the instrument Warning Do not interrupt the flashing because the loader program for Flashlt 32 is included in the BIOS otherwise PR1713 needs to be repa
139. spects receive RxD DCD RxD TxD DTR GND RTS CTS Al PR1713 00 with PR1713 04 In case of Hardware Handshake Connect lines with the opposite side see above The modem is controlled by the signals of the interface PR1713 04 see above In case of Software Handshake X On X Off control has to be enabled the Lines RxD TxD and GND are connected 1 1 Provide links on both sides between RTS CTS and DCD DTR DSR or link RTS CTS DSR With this operation mode the modem answers automatically with a OK after a command at Now you can start to set the parameters with a terminal a auto answer on This parameter is stored in register sO of the modem The command is atsO 1 b DCD on Data carrier detect is always on Command is at amp cO c hang up on DTR off Modem assumes command state when DTR goes on to off The command is at amp d1 Other modems than Elsa Microlink 33 6TQV may require at amp d2 hang up if DTR goes to off If this parameter is wrong the auto answer function is not working or the modem will not hang up In case of problems consult the manual of the modem to find out the right commands PR 1713 rel 1 10 17 Connection to an RS 485 bus two wire system Supervisory system PLC RxA RxB TxA TxB GND TxA TxB RxA RxB GND TxA TxB RxA RxB GND PR1713 00 slave 1 PR1713 00 slave n Connection to an RS 485 bus four wire system Supervisory system PLC RxA RxB TxA TxB GND
140. sub menu Service by pressing key T PR1713 00 IRG IL SOX SOR MORRO ROK Test Inputs Outputs IMIG BOX ROK REGO 09531951 1 I O Slot 1 PR1713 04 Serial Interface RS232 and RS485 2 I O Slot 2 PR1713 06 Analog Out 3 I O Slot 3 PR1713 12 Digital I O 4 I O Slot 4 PR1721 01 Profibus Interface E Exit The modules on sockets 1 to 4 identified by the PR1713 system software are displayed e Select and test module The mask corresponding to the module type is displayed by entry of the socket number 1 4 Description of the module specific tests is in the following sub sections e Leave sub menu Test Input Output E Exit After leaving this mask E return is to sub menu Service Only then all outputs set during testing are reset and the output commands of the PLC programs are retransmitted to the process 88 rel 1 10 PR 1713 5 8 3 1 PR1713 04 serial I O module testing At the PR1713 hardware test level PR1713 04 serial interface cards can also be tested provided that the following jumpers are fitted in the module terminal blocks Terminal strip B RS 232 B1 B2 B3 B4 B5 B6 B7 B8 rear top row DCD RXD DIR Sign RTS CTS RI GND Switch on the card 1 On 2 Off 101 3 On 4 On 5 On Terminal row A RS485 422 A1 A2 A4 A A7 front bottom row Switch ON Sign TxB TxA HRxB RxA nc nc nc acc to table GND The i
141. t indicator range FSD nd Error2 Error3 2E weight Scale with spans for error and load PR 1713 rel 1 10 43 4 4 3 Set Parameters Calibration The softkey Param changes the measuring parameters New WModifyW Param In menu Set Parameters the most important PR1713 operating parameters can be adjusted Various functions can be selected Display Parameter range Analog filter Analog filter for the measuring signal off on Select Filter characteristics Bessel aperiod or o In case of Digital filter on Enter filter cutoff frequency 0 10 up to 5 00 Hz instead of Measuretime Fcut Measuret ime is fixed to 50 ms Test mode Operating mode for the test value Absolute F S D Relative 0 ow amp M Operating mode W amp M Disabled Enabled With W amp M enabled e Printing only on W amp M printers special protocol e No calibration possible below 0 3 mV V at 3000 d negative weight without weight unit remote display dimmed Measuring time 50 ms or multiples of 100 ms 0 05 0 10 0 20 2 00 Time for standstill detection 1 8 M Measuring time Time for cyclical automatic zero tracking 0 100 M Time for abort of inexecutable tare zero set action 0 100 M Range for standstill detection 0 10 00 d Zero set range and range for automatic zero tracking 0 500 00 d Range for aut
142. t e Ha De 7 Multirange scale 43 Relay Output 5 2 ine ere ettet eren 20 21 TEMOLE Dus 4 5 25 remote displ y z iusso BAUR 13 59 Operation atte ats 33 7 Operator Device at 47 R pOrtt0 ope Beer iere pe e ee Re ehe 46 Optiorler ce edet eu 7 Res lutioti unser eS 70 OHH Se OU IB RE I 7 RS232 gU Phe ate Se 13 14 optocoupler 1 eene 7 RS 422 Ra 14 Opto Input onsere issid ee essei riii reto ids 20 RS ASS ects discov ies toe e ee i e TEE 14 carter irr eb ren DH REPE FR 7 RISCS eri Pere vete 15 overlo d 69 83 S P 88 01 Int tfaGe oi ente ee tem tet 47 parameter 70 Safety lunts idaieedeietatie dein eet 1 2 Parainetets i ostio etes 31 1 seruo ovate teed ee ee ts eto e teta peces 83 PGreland 11 Selecting the calibration 40 Phase 7 tenete 45 power supply scan tie nite entienden 2 serial interface iae 7 58 Power supply 1713 01 2 E eter ener 54 PR 1721 7 28 Set Glock eiie Seed ihre
143. t is a powerful system for control of weighing and batching processes and combines all functions such as convenient operator interface weighing and batching controller PLC interfaces 2 1 Basic instrument survey e Accuracy 5000 d for the internal weighing point 2428 Green fluorescent display for weight 2 lines for text js e Front panel controls function keys 2087 Stainless steel housing sealed to IP65 with EMC cable glands Hee PC AT keyboard connectable no protection to IP65 U EI EL TE EL EL EL E e Serial interface RS 232 built in for e g printer remote display terminal or communication e Extensible by means of options 3 sockets RAM extension 1 socket for a field bus module e All interfaces except the RS 232 interfaces are galvanically isolated Built in power connection for 230 V 115 V AC protection class protective earth e All connections in the housing are made to plug in terminal blocks except the power cable e The unit is suitable for mounting in a panel cut out for wall mounting or as a table top unit Calibration or configuration of PR1713 is menu guided via the operator device keys on the front panel or an additional VT100 terminal at Builtin or an other RS 232 interface e Calibration by means of weights or by entry of the mV V values without additional calculations e Configuration of the interface cards e
144. ta remain unchanged PR 1713 rel 1 10 37 The calibration data remain always unchanged They can be changed only in the calibration procedure lf warm start is not possible Cold all programs and tables loaded in the memory are deleted Flash program loading also parts STOP Key pressed Cold V Erase VW Flash Erase deletes the EAROM By Erase all calibration and configuration data are adjusted to the factory settings Safety prompt for Erase all data YES Data are overwritten YES V W No NO all data remain unchanged Possible error message Erase not possible when switch CAL is closed CAL Jumper closed If a warm start is not possible e g due to a system crash or because of an empty battery various texts are displayed on the upper display line Reboot done Restart from the operating level was carried out Flash complete Loading of a new software was completed Flash cancelled Loading of a new software was canceled Fatal error reboot fatal error occurred before restart No valid firmware The firmware checksum is faulty BIOS too old Faulty BIOS version BIOS too old after new firmware was flashed SLOP Quvb Reset Unit was reset with Stop key and Quit key The BIOS must not be flashed without this message Do not interrupt the flashing because the loader program for Fla
145. te dee 33 ADD TAN arro p MD 33 4 2 3 Operating concept Commissioning 33 2 3 MAIN MENU ett tene metet at ala ire e ae Be 34 4 3 1 Configuration area Setup ai iu eunte eiae dieere et pee EEES ENES 34 4 52 Boot MENU derr etr e E Peer ep eer eere ede ede et eere eere eere eire Per ete eet lectos t dde foede deed dde supe 36 4 4 CALIBRATION WEIGHINGPOINT PARAMETERS sssssccccccecssssssecccecccceeeeususeeeccceeseaueseeeecceeeseuanseccceessuauaeeeeceeeseaaanees 39 4 421 Calibration sequentes i i tette Pays et daha dee e Mae dL e e dab cots itt ete deeft tete 39 43 2 Start messages autu ederet ee e pre ge pH nete 39 44 3 Set Parameters x db ti ierit feet touted nd dope ete Aas ee Be aug eee y esee aute edet op dee roo dee Et e ag aa 43 LI E E A A AN EH E 44 4 5 CONFIGURATION OF NOT WEIGHINGPOINT PARAMETERS 44 4 5 Set CloGk ceu aee eH E WO ENTIA 44 45 2 Serial POTIS eee eet tre rete tret des ede esee eese dete e denter e ee edis va depot eio rose doy aeuo d 45 4 9 3 SoftWare parameters deras ode npe ere DE e Vp bep re e POE ERES 45 45 4 Fieldbus Paramelter idet e eee AE EEE EEE et eere det eode de deer eve uer de BAEC EPI de ERE deu 47 4 5 5 Show Boardnumber
146. ter only once per device The following settings are useful dependent of protocol These settings can also be changed subsequently Possible protocols _Default settings data bits echo _Application example _ Rem None X ON 8 none 1 9600 ANSI enabled System console 1 EWCOM slave V1 7 even 1 9600 A EW protocol V1 5 6 EWCOM slave V2 8 even 1 19 2 A EW protocol V2 PR1740 6 EWCOM slave V3 8 even 1 19 2 A EW protocol V3 DDE server 6 7 RTS CTS X ON standard as X On Printer 3 W amp M printer 7 even 1 9600 raw I O disabled W amp M printer 2 Remotedisplay 7 even 1 9600 raw I O disabled PR16xx remote display 4 Remarks 1 A terminal or a PC with a terminal emulation program is used as system console 2 An FX880 PHO02 Epson printer permits W amp M weight data print out 3 Via this protocol print out of all PR1713 configuration data and weight print out during weighing point calibration if necessary are made 4 PR1713 sends the remote display telegram successively for all 2 weighing point modules This is followed by a pause of approx 80 msec Data contents see PR1627 and PR1628 documentation 5 Protocol for communication with PR16xx units 6 For operation with PR1750 7 For operation with PR1791 DDE server 60 rel 1 10 PR 1713 5 2 4 Entry of the software licence number Calling up mask License configuration is done from sub menu Configuration by pressing key L
147. tialization all data remain unchanged 104 rel 1 10 PR 1713 7 4 Index 1 10 fold magnifier eene 40 A Adjusting the terminal emulation program 53 Allow quits masa ede Ld 46 Analog card eletti 7 18 Analog outp t n repetere tete repete reos 99 analog output module eene 89 Analog output module testing eesees 89 Analog test etes 67 application 34 Batching 7 Battery cp EE 4 277 46 61 BCD output risien intos 7 22 uns eoa eana EE RATER 47 tte daa sie 13 CAL ses ee i a eee a 39 66 CAL SWIICH eerte 34 64 103 Calculate test rH etse 42 CalibratlOm zi xe erre tete ie ted 69 71 T7 Calibration error messages eeeeeeee 42 Calibration in one step with weights 72 Calibration weight eene 70 Calibration without weights eese 78 Calling up and display of the weighing point calibration TAS quK 64 erede eel 10 PE 36 Cold st tt siea det ete 32 component 7 Configuration reine eed 54 57 Configuration Calibration 33 Corinecti
148. urn to the main menu is by pressing key E 5 2 1 Set date PR1713 00 Rel XX XX X XX XX XXXX XX XX Configuration SOX oxox 1030062106 D Set date T Set time Enter new date 31 05 1999 Press key D Message Enter new date 31 05 99 _ is displayed Enter the new date e g 05 12 99 Press key the line is removed from the display if the entry was correct With faulty entry message bad date enter new date 31 05 99 _ is displayed Check against the header top right 58 rel 1 10 PR 1713 5 2 2 Set time Configuration MO OX ROOK eo 1320 Gs IG D Set date T Set time Enter new time 13 06 16 e Press key T e following message is displayed Enter new time 13 06 16 e Enter the new time e g 13 07 00 e Press key to remove the display e Check against the header top right 5 2 3 Serial interface configuration Calling up serial interface configuration mask Change serial I O parameter is done from sub menu Configuration by pressing key C PR1713 00 Rel XX XX X XX XX XXXX XX XX Serial I O setup BOX REGO 09551 851 Slot 1 TTY2 RS232 Protocol X ON Baudrate 9600 Bits i 8 Parity None Stopbits Slaveadr ELLE Device ANSI Echo Enabled When calling up this mask the communication is disabled In the upper mask area the parameters of a serial interface name and input field
149. ution c d multiplied by 100 cd Centi d one hundredth of a display step 5 6 2 Editing functions for parameter entry Weighing point selection Weighing point selection is before calling up this weighing point calibration mask see above Weighing point selection is by means of the two cursor keys T and J Thereby the actually selected weighing point is highlighted by inverse display ltem selection Direct access is only to item Fullscale Item selection is by entry of a letter unlike the cursor keys as for weighing point configuration parameters Parameters Resolution are not accessible only used for informative purposes Entry change of parameter e Enter the required parameter value value and dimension PR 1713 rel 1 10 71 e Change the entry by overwriting select character with the cursor keys Delete by pressing the backspace key lt and re enter e the enter key to complete the entry e Subsequently the entry is checked 5 6 3 Adjusting the full scale value Fullscale Enter the full scale value into item Fullscale Open the entry dialogue by entry of letter F Prompt for entry of the measurement value Enter new fullscale 3000kg E to exit The old measuring range with dimension is displayed in square brackets default value 3000 kg PR1713 expects the following entries Measuring range with comma or point no or one or several spaces dimension g kg or t
150. werb oder schriftliche Einwilligung des unheberrechtlichen Eigent mers GWT nicht benutzt werden Durch die Benutzung dieses Produktes werden obige Bestimmungen von Ihnen anerkannt Veuillez noter s v p L exploitation de ce produit ne doit seffectuer que par du personnel autoris Dans votre comespondance se rapportant au pr sent produit veuillez toujours sp cifier le num ro de type la description et le num ro de version ainsi que tous les num ros de licence en rapport avec ce produit Important Les droits d auteur de toutes les parties de ce produit sont r serv s Ce produit ne doit tre ni utilis ni chang ni copi sans achat de la licence ou accord par crit L utilisation du produit implique la reconnaissance des conditions mentionn es ci avant GWT GLOBAL Weighing Technologies GmbH All rights are strictly reserved Reproduction or divulgation in any form whatsoever is not permitted without written authority from the copyright owner Printed in Germany PR 1713 rel 1 10 Contents 1 SAFETY HINTS ELECTRICAL PROTECTION CLASS sccccssssssssssocsssssssssscsssssssssssscccssssssssssssssessessses 1 1 APPLICATION OF THE INSTRUMENT cccccccccssseseeccccesecascassseeecccceeeeaasseececceeseauseseeccceeseeuansececceeseuaeseeececeessuaaneeeeceeeeeaaa 1 2 INITIAL INSPECTION 1 3 BEFORE COMMISSIONING irena eaaa aa i A E
151. y blocks bytes in largest block free memory handles Physical Memory Bank 1 Physical Memory Bank 2 Hit any key to continue SOx se xoox 0925315531 The following information is displayed in the mask e free memory capacity bytes Used memory capacity bytes Free memory capacity bytes Number of available blocks Largest available block bytes Hit any key to continue to leave the mask bytes maximum memory available bytes memory in use bytes free memory blocks bytes in largest block PR 1713 rel 1 10 87 5 8 2 Show hardware configuration Calling up mask Show hardware configuration is done from sub menu Service by pressing H Hardware PR1713 00 OK BOX SOK Service IMG OK I O Slot 1 PR1713 04 Serial Interface RS232 RS485 I O Slot 2 PR1713 06 Analog Out I O Slot 3 PR1713 12 Digital I O I O Slot 4 PR1721 01 Profibus Interface Hit any key to continue e The modules identified by the PR1713 system software are displayed e With modules containing firmware the module software version is also displayed e key to continue 5 8 3 Testing the input and output modules e During module testing T no outputs are set by the PLC programs i e the PLC programs continue running the inputs are read but the output commands are not transmitted to the process Calling up mask Test Inputs Outputs is from

PR1713 Installation Manual

Contents

Download Pdf Manuals

Related Search

Related Contents