FXS Digital Communications System Installation and Application
Contents
1. NC No Connection Wiring The IVPC Card ivpe_con cdr Installing The IVPC 9 5 Installation And Application Instructions IMI89 290 Programming The Telephone system For IVPC Operation When you plan for a digital station port to become a voice mail port you must program the station port as a voice mail port Use entries on the VMMI programming Peripherals Voice Mail Extension Table menu to do this At default an VPC station port is programmed for voice first signaling that is the station does not ring when called When you add the IVPC port to the voice mail link table the station port automatically becomes a tone first signaling port regardless of the voice or tone first setting for the station port in station programming Troubleshooting The IVPC Installation Do not bridge DTMF intercepting test equipment across the line cord that runs between an IVPC port and a digital station port A DTMF grabber is an analog device and it will not work on a digital IVPC port The four ports of an IVPC identify themselves to or synchronize with the telephone system that is they send the phone type signal They do this the first time the voice card driver known as RHETDRV loads in memory after initial computer power up Any subsequent power up does not cause the VPC ports to re synchronize with the switch Running RDSPEXIT or performing a Ctrl Alt Del that is performing a soft reset operation does not reset the IVPC2. FXS Digital Communications System Installation and Application Instructions for the Motherboard Based System Computer Components IMI89 290 03 05 00 1 printed in U S A The Rising Star Comdial strives to design the features in our communications systems to be fully interactive with one another However this is not always possible as the combinations of accessories and features are too varied and extensive to insure total feature compatibility Accordingly some features identified in this publication will not operate if some other feature is activated Comdial disclaims all liability relating to feature non compatibility or associated in any way with problems which may be encountered by incompatible features Notwithstanding anything contained in this publication to the contrary Comdial makes no representation herein as to the compatibility of features Issued 2 12 97 IMI89 290 Installation And Application Instructions Contents 1 Introducing The FX Series System Computer Components 1 1 Handling Static Sensitive Components 1 2 2 Installing The Computer Motherboard 2 1 Installing The Motherboard 4 0 0 20 044464 Weg eee rates Ayana ener eae ea 2 1 Detailing The Motherboard Device Locations 2 2 3 Installing The FX Series System Computer Power Supply 3 1
3. 82438VX B so su Port LPT 1 Connector oy ROM Drive Video Card PCI Slot S Connector Network Interface Card PCI Slot2 PCI Slot3 3 _ ISA Slot a IVPC ISA Slot o i i 27 2 z Serial Port Expansion Card ISA Slot q z R ISA Slot l R pe_mbrd cdr NOTE Your system s motherboard may differ from this typical example Refer to the literature included with your system for complete details Locating The Device Connections 2 2 Installing The Motherboard IMI89 290 Installation And Application Instructions Installing The FX Series System Computer Power Supply The power supply provides the power needed to run the FX Series system computer motherboard its special purpose circuit cards the floppy disk drive the hard disk drive and the compact disk drive The power supply delivers either 110 VAC or 220 VAC depending upon the setting of a switch Be sure the switch setting matches the local voltage specifications Installing The Power Supply The computer power supply is located in the opening at the top right rear of the common equipment cabinet It attaches to the cabinet with three supplied machine screws Secure the computer power supply to the common equipment cabinet with three supplied screws Computer Power Supply Top Right Rear Of The Common Equipment Cabinet Locating The Computer Power Supply Installing
4. includes video card voice card network card You may find that the factory has installed everything that your system needs and you do not need to install any of these elements during initial installation However if you need to add or replace a part in the field at a later date you will need some instruction This publication serves that purpose by describing the installation of the basic elements into the FX Series system computer This publication also includes any unique setup and application information needed to make a particular element fully operational Introduction 1 1 Installation And Application Instructions IMI89 290 Handling Static Sensitive Components A computer circuit board is a very sensitive assembly and is susceptible to damage caused by electrostatic discharge You can damage its components very easily by handling the circuit board improperly This damage is not easily detectable yet may cause critical data errors during operation Electrostatic discharge damage is permanent it cannot be repaired therefore you must take precautions to prevent it from occurring You can refer to Comdial publication IMI01 005 Handling Of Electrostatically Sensitive Components for general electrostatic discharge information The following paragraph discusses specific handling precautions that will help prevent electrostatic discharge damage Before handling any circuit board in the FX Series common equipment c
5. You must cycle the computer s power to reset the VPC if it becomes necessary If one or more ports on an IVPC do not synchronize with the telephone system for example they do not appear as present with the S in the telephone system s station types printout disconnect both lines cords from the IVPC board wait for at least two seconds this is the time out duration coded in the VPC firmware to detect that the ports are off line reconnect the line cords top VPC jack first If the VPC ports still do not synchronize cycle the computer s power If this action does not cause the IVPC ports to synchronize the VPC may be defective and require replacement 9 6 Installing The IVPC IMI89 290 Installation And Application Instructions When an IVPC looses synchronization with the telephone for example if you disconnect an IVPC port from the digital station port the VVP application causes a No comm display for the port status and causes an alarm to sound and the computer monitor to display the following error message SYSTEM ERROR 5209 IVPC port x lost communication with the phone system When an IVPC reestablishes communication with the telephone system for example after an IVPC port was disconnected and reconnected to a signal station port the VVP application sounds an alarm and displays the following error message and the system logs errors 5208 and 5209 in the ERROR LOG file SYSTEM ERROR 5208 IVPC port x reestablish
6. s metal connector bracket with the opening in the cabinet and mate the card to the motherboard s third ISA slot Do not force the card into the connection it should slide into place with gentle pressure when oriented properly Once you have mated the card with the motherboard secure the card by attaching its metal connector bracket to the common equipment cabinet using the screw removed in step 1 This action secures the card in place and provides a rigid connection for the serial data device cables Installing The Serial Port Expansion Card 8 1 This page remains blank intentionally IMI89 290 Installation And Application Instructions Installing The IVPC The Comdial Integrated Voice Processing Card IVPC is a proprietary digital four port voice processing card that along with the Versatile Voice Processing VVP application software provides a full featured voice mail and automatic attendant application for system users The VPC allows connection between digital station ports on the telephony portion and the computer portion of the FX Series system The IVPC and associated cables provide the electronic interface while the VVP application software provides the user interface to the IVPC Understanding The IVPC Characteristics The IVPC cable connects to a digital station port and provides four voice processing ports supplied to two standard modular telephone jacks which are configured as RJ 14C jacks The left jac
7. IDE ribbon cables provide PCI Slots several connectors along their __ ISA Slot I length This allows one data ISA Slot cable to serve two drives when ISA Siot J that need occurs In the case of the floppy drive in the FX CSA Sot I pe_mbrd4 cdr Series system computer use NOTE Your system s motherboard may differ from this typical example the first connector on the cable Refer to the literature included with your system for complete details that properly mates with the Locating The Motherboard s Floppy Drive IDE Connection floppy disk drive s IDE data connector 82437Vx vx x J11 49 8237158 PIX3 IE JRI J22 dl KBD Controller i n a 2 The IDE connector is not keyed The proper orientation is to connect the pin 1 of the ribbon cable connector to the pin 1 of the disk drive connector Another method TE Power to help orient the connection properly is to Connection align the cable connector so that its red tracer marking is closest to the floppy disk drive s power connector Sometimes it is hard to discern these connector markings IDE Ribbon i making it possible to mate the connection Cable From improperly A sure indication of improper Motherboard Connection connection is a steady on condition of the disk drive s status light when you operate Floppy Disk the drive Should the drive s status light Red Tracer Mark Drive Chassis remain on steady powe
8. The Computer Power Supply 3 1 Installation And Application Instructions IMI89 290 Connecting Power To The Internal Components The computer power supply has a multipurpose power cable as an integral part of its assembly This cable terminates in several connectors of different types to mate with various computer components In general the connectors are keyed for proper insertion however there are several items that you must take into consideration 1 While the two power plugs for the motherboard are keyed so h NOTE Your system s motherboard may differ from this typical example that they mate with the Refer to the literature included with your system for complete details motherboard connection in only one direction it is possible to Ki reverse the position of these two til plugs To avoid this reversal ale 12 se SSSR a note that each plug has two eae Power Connector black wires along with several a Re LE mu other wires of different colors b orient these two plugs so Motherboard that the black wires in each connector are next to each other and located at the center of the motherboard connector Power Supply Plugs pe plug cdr c press the plugs onto the motherboard connector in this orientation Orienting The Motherboard Power Plugs 2 The large white power plugs for the drive assemblies are keyed and will mate with their Yellow Wire
9. corresponding connectors on the Power drives in only one orientation Connection The floppy disk drive requires a Red Wire small power plug and this plug is not keyed It is possible to improperly plug the small plug IDE Ribbon onto its mate on the drive chassis Cable From To insure that you mate the plug Motherboard Connection and connection properly orient the plug so that its red wire is Floppy Disk closest to the IDE ribbon cable Red Tracer Mark D ve Chassis connector and its yellow wire is closest to the edge of the drive assembly chassis bottom view pe_drive cdr Orienting The Floppy Drive Power Plug 3 2 Installing The Computer Power Supply IMI89 290 Installation And Application Instructions Connecting AC Power For the AC power connection to the power supply use the same dedicated 115 VAC 15 AMP circuit with a third wire ground supplied to a standard electrical outlet NEMA 5 15R and protected by its own circuit breaker that you use for the telephony portion of the system NOTE While you may notice a physical difference in the appearance of the two supplied AC power cables there is no electrical difference You can interchange the two AC power cables between the telephony and computer portions of the FX Series system as you See fit To provide protection against surges and spikes that may appear on the AC line to the computer portion of the FX Series system install a plug in power line surge protec
10. of floppy disk technology and manufacturers of floppy disks recommend that you back up any data that you store on floppy disks Some advisors even suggest that you back up floppy disk stored data at least twice Installing The Floppy Disk Drive The floppy disk drive assembly mounts in a drive cage along with the computer s hard drive The cage mounts in an opening at the top front of the FX Series common equipment cabinet Mounting The Floppy Disk Drive In The Cage Mount the floppy disk drive in the drive cage and attach it to the cage with the four supplied screws two on each side of the cage ao SO Mounting Cage 3 5 Inch Floppy Drive Hard Drive Mounting Hardware two places each side for either drive Installing The Drive In The Drive Cage Installing The Floppy Disk Drive 5 1 Installation And Application Instructions IMI89 290 Mounting The Drive Cage In The Cabinet Mount the drive cage in the common equipment cabinet by inserting it from the inside of the cabinet into the opening at the top front of the cabinet and attaching it with the four supplied screws Common a Equipment Drive Cage Capit With Installed Floppy Drive And Hard Insert drive cage Drive into cabinet opening from rear and attach with four supplied screws Installing The Drive Cage In The Cabinet 5 2 Installing The Floppy Disk Drive IMI89 290 Installation And Application Instructions Connecting The Flo
11. places each side for either drive Installing The Drive In The Drive Cage Installing The Hard Disk Drive 4 1 Installation And Application Instructions IMI89 290 Mounting the Drive Cage In The Cabinet Mount the drive cage in the common equipment cabinet by inserting it from the inside of the cabinet into the opening at the top front of the cabinet and attaching it with the four supplied screws Common o a Equipment Drive Cage Cobimei With Installed Floppy Drive And Hard Insert drive cage into cabinet opening from rear and attach with four supplied screws Drive 1 a T cage 2 cdr Installing The Drive Cage In The Cabinet 4 2 Installing The Hard Disk Drive IMI89 290 Installation And Application Instructions Connecting The Hard Disk Drive There are two cable connections that you must make to the floppy disk drive the power connection and the IDE data connection Connecting The Hard Drive Power Plug The computer power supply s multipurpose cable provides a plug that mates with the hard disk drive power connector To make the power connection take the following steps 1 Locate one of the large white plugs attached to the power cable bundle There are several plugs available Choose the plug that is most convenient to use 2 The power plug is keyed it is not possible to connect it improperly Simply locate the hard drive s power connection at the rear of th
12. 9 1 ne CE ae Introducing The FX Series Motherboard Device Locations 2 2 Da Loose System Computer Components 1 1 Detailing The Motherboard 2 2 Publication Index 1 Publication Index IVPC Characteristics Understanding The 9 1 IVPC Installation Troubleshooting The 9 4 IVPC Installing The 9 1 9 2 IVPC Operation Programming The Telephone System For 9 4 IVPC Strapping The 9 2 M Motherboard Installing The Computer 2 1 Mounting the Drive Cage In The Cabinet 4 2 5 2 Mounting The Floppy Disk Drive In The Cage 5 1 Mounting The Hard Disk Drive In The Ce led session 4 1 Multiple Serial Port Card Installing The 8 1 N Network Card Installing The 10 1 2 Publication Index IMI89 290 P Power Plug Connecting The CD ROM Drive Power Plug Connecting The Floppy Drive Power Plug Connecting The Hard Drive Power Supply Installing The Programming The Telephone System For TVPC Operation ess Lisseur S Strapping The IVPC 2250 soupe T Troubleshooting The IVPC Installation U Understanding The VPC Characteristics V Video Card Installing The 9 4 9 1 This manual has been developed by Comdial Corpor
13. Computer Telephony Integration CTD applications You must install the serial port expansion card in the third ISA slot The following Typical FX Series System 1 Computer Motherboard illustration points out this location Install the serial port expansion card in the DMM PANK 2 3 4 SIMM4 BANK 1 3 manner described below money SIMM2 BANK 0 sal x Notice that the card has a wide metal SMMIBANKO que A connector bracket along one edge that FOD _HODT Bi cles contains a multiple pin cable Coan Hooe connector This connector accepts a eae ae 3 oO breakout cable that makes the o mw 3 re i PCI Slot3 individual serial data connections 3 C Asor gie available You must remove the blank noe 3 plate from the common equipment Serial Port a sa sot ae Expansion Card cabinet that covers the opening in front ISA Slot of the third ISA slot to make room for pe_mbrd5 cdr NOTE Your system s motherboard may differ from this typical example Refer to the literature included with your system for complete details the card s connector bracket Save the screw because you will need it later The card s edge connector is keyed so you can only mate the card to the motherboard connection in one Locating The Serial Port Expansion Card Connection orientation Align the card
14. Installing The Power Supply serieus fan eae wes PS amp 6 SA eae GaN a oe oe ee 3 1 Connecting Power To The Internal Components 3 2 Connecting AC POwet 2 4200 vier es yee cts eee ch eee oe tn a een An ee 3 3 4 Installing The Hard Disk Drive 4 1 Installing The Hard Disk Drives 5 ys0 450 cag dees i eed a aetna ee ee wae as 4 Mounting The Hard Disk Drive In The Cage 4 Mounting The Drive Cage In The Cabinet 4 2 Connecting The Hard Drive 224 054 fou lines Re RS Se BRE Oe eee se 4 3 Connecting The Hard Disk Drive Power Plug 4 3 Connecting The Hard Disk Drive IDE Data Cable 4 3 5 Installing The Floppy Disk Drive 5 1 Installing The Floppy Disk Drive 244 2 042 at eee trs Pe ee rer ere eee 5 1 Mounting The Floppy Disk Drive In The Cage 5 1 Mounting The Drive Cage In The Cabinet 5 2 Connecting The Floppy Disk Drive 2222 dues dima das eis ee ew hates es 5 3 Connecting The Floppy Disk Drive Power Plug 5 3 Connecting The Floppy Disk Drive IDE Data Cable 5 4 Contents iii Installation And Application Instruction
15. abinet place the cabinet on a conductive mat and ground that mat to a good earth ground The third wire ground of the AC power line is an acceptable grounding point A grounded conductive mat provides a safe electrostatic discharge path Always prepare such a static safe work area and place the equipment cabinet on it before you service any Static circuit boards Wrist NS Strap ESD Protective _ Always supply yourself with a static Mat Typical Earth discharge wrist strap properly ground psp Proective D Td Gioia it to a good earth ground and wear it Worksurface gt A every time you handle electronic circuit boards The factory includes a static discharge wrist strap for your use with the FX Series system Static2 Install your static discharge wrist strap on your bare wrist and adjust it for a snug fit Be sure that the strap is touching bare skin Mat and is not isolated by clothing Connect the wrist strap cord between the wrist strap and an AC or earth ground The factory ships uninstalled circuit boards for the FX Series system in static protection bags for safe keeping Keep a board in its bag until you get it to a static safe work area and are properly wearing a static discharge wrist strap You can then safely remove the board from its static protection bag and install it in the system Common Point Ground lt ESD Protective Detailing A Static Safe Work Area 1 2 Introduct
16. ation the Company and is intended for the use of its customers and service personnel The information in this manual is subject to change without notice While every effort has been made to eliminate errors the Company disclaims liability for any difficulties arising from the interpretation of the information contained herein The information contained herein does not purport to cover all details or variations in equipment or to provide for every possible contingency to be met in connection with installation operation or maintenance Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser s purposes contact Comdial Inside Sales Department Charlottesville Virginia 22906 IMI89 290 03 05 00 printed in U S A Printed in U S A 709810 724 Rev i COMDIAL The Rising Star Comdial Corporation P O Box 7266 Charlottesville VA 22906 7266 1 800 COMDIAL www comdial com
17. ation Instructions IMI89 290 Connecting The IVPC Connect the IVPC voice processing ports to digital station ports using standard four conductor telephone To guard against cross talk between the two wire pairs in a single four wire line cord be sure to split the two tip and ring pairs as soon as they emerge from the IVPC s modular jacks line cords Also you must connect the four ports of an IVPC within the same eight port group on a digital station card You also must not split the IVPC ports between two digital station cards or between the upper eight station ports and lower eight station ports of a single 16 port digital station card Connect the serial data cable between the computer s COM1 connector and the COM1 jack on the telephony portion of the system 9 4 Installing The IVPC IMI89 290 Installation And Application Instructions Typical Station Connector Block To Common Equipment For VVP Connect Cabinet Computer COM 2 To Telephony COM 2 ss TP RING TP RING S Tip 1 Tip 2 Ring 1 Connect Digital Station Ports To IVPC IVPC Jack Arrangement PIN JACK 1 JACK2 Pin Locations On Jack Front View L Ll NC NC TIP 2 TIP 4 RING 1 RING 3 TIP 1 TIP 3 RING 2 RING 4 ain ER JQ IN NC NC
18. e hard drive assembly chassis and mate the connectors Installing The Hard Disk Drive 4 3 Installation And Application Instructions Connecting The Hard Drive IDE Data Cables The IDE data cables are the flat ribbon cables that connect between the computer s motherboard and the hard IMI89 290 3 5 Inch Floppy Disk Drive Hard Disk Drive disk drive The IDE cables are keyed on COMM BANK amp the motherboard end You can only SIMM4 BANK 1 connect them to the motherboard in one SIMM3 BANK SIMM2 BAXK 0 orientation This is not the case when you SIMMI BANK 0 connect them to the drive assemblies At FDD SRAM SRAM these connections there are two E a C t x i uss PRN ompac considerations that you must note En Disk Drive Sgt 5 1 IDE ribbon cables provide several pelo 3 connectors along their length This eee eee Sa allows one data cable to serve two z me Ior EE Le drives when that need occurs In the ey eee Me PES a CE ISA Siot I fa case of the drive assemblies in the FX a Series system computer use the first L saso connector on the cable that properly arn you pe_mbrd4 cdr system s motherboard may differ from this typical example mates with the drive s IDE data Refer to the literature included with your syst
19. ed communication with the phone system If you ever reset the telephony portion of the FX Series system it is a good practice to also cycle the computer s power Installing The IVPC 9 7 This page remains blank intentionally IMI89 290 Installation And Application Instructions Installing The Network Interface Card The network interface card NIC provides the FX Series system computer with an Ethernet interface between it and external data equipment Ethernet is a data protocol for creating a local area network or LAN that connects together devices such as computers data printers work stations terminals and so forth within the same location Typical FX Series System Installing The Network Card Computer Motherboard 3 2 8 5 _DIMM BANK 2 You must install the NIC in the second PCI a SMART j slot The following illustration points out this SMS RANK Se location Install the network interface card in con a vai JIE the manner described below COM Foo HOT si ae uss PrN HDo2 1 Notice that the card has a wide metal FES x 5 Network Interface Card F Paso g g connector bracket along one edge that e 82 8 contains cable connectors These are a ca Sm connections for the external network f E E es cables You must remove the blank plate a gt m7 ISA Slot from the common equipm
20. em for complete details connector cee Power Connection IDE IDE Ribbon Ribbon Cable From Cable Motherboard Connection Red Tracer Mark Drive Chassis bottom view pe_drvel cdr Orienting The IDE Connection 4 4 Installing The Hard Disk Drive Locating The Motherboard s Hard Drive IDE Connection 2 The IDE connector is not keyed at the drive end The proper orientation is to connect the pin 1 of the ribbon cable connector to the pin 1 of the disk drive connector Another method to help orient the connection properly is to align the cable connector so that its red tracer is closest to the drive s power connector Sometimes it is hard to discern these connector markings making it possible to mate the connection improperly A sure indication of improper connection is a steady on condition of the disk drive s status light when you operate the drive Should the drive s status light remain on steady power down the system and reverse the mating of the drive s IDE connection IMI89 290 Installation And Application Instructions Installing The Floppy Disk Drive The FX Series system computer provides a 3 5 inch floppy disk drive You can use this drive to load programs and software data into the computer s memory and to store data that the computer has generated NOTE Computer consultants advise that you should consider data that you store on floppy disks to be temporary Computer consultants designers
21. ent cabinet that or covers the opening in front of the second ISA slot to make room for the card s connector bracket Save the screw because you will need it later Locating The Motherboard s Network Card Connection 2 The card s edge connector is keyed so you can only mate the card to the motherboard connection in one orientation Align the card s metal connector bracket with the opening in the cabinet and mate the card to the motherboard s second PCI slot Do not force the card into the connection it should slide into place with gentle pressure when oriented properly 3 Once you have mated the card with the motherboard secure the card by attaching its metal connector bracket to the common equipment cabinet using the screw removed in step 1 This action secures the card in place and provides a rigid connection for the external network cables Installing The Network Interface Card 10 1 This page remains blank intentionally IMI89 290 Publication Index A F AC Power Connecting 3 3 Floppy Disk Drive Installing The 5 1 Floppy Drive Connecting The 5 3 C Floppy Drive Mounting In The Cage 5 1 CD ROM Drive Connecting The 6 2 H CD ROM Drive Installing The 6 1 Component Handling Static Sensitive 1 2 Handling Static Sensitive Components 1 2 Components Connecting Power To 3 2 Hard Drive Connecting The 4 Components In
22. ion IDE Ribbon Cable Connection IDE Ribbon Cable From Motherboard Red Tracer Mark Drive Chassis bottom view pe_drvel cdr Orienting The IDE Connection Installation And Application Instructions 3 5 Inch Floppy Disk Drive Hard Disk Drive Oc DIMM BANK 2 a SIMM4 BANK 1 SIMM3 BANKI SIMM2 BAMK 0 ol xl COM1 SIMMTIBANK 0 s H COM2 FDD Hoi uss Pru HOD2 nen i isk Drive PCI Slot PCI Slot2 PCI Siot3 __ ISA Slot bo ISA Slot ISA Slot LL ISA Slot I pe_mbrd4 cdr NOTE Your system s motherboard may differ from this typical example Refer to the literature included with your system for complete details Socket 5 7 82437 8237158 PIX3 il wm KBD Controller Locating The Motherboard s CD ROM Drive Connection 2 The IDE connector is not keyed The proper orientation is to connect the pin 1 of the ribbon cable connector to the pin of the drive connector Another method to help orient the connection properly is to align the cable connector so that its red tracer marking is closest to the drive s power connector Sometimes it is hard to discern these connector markings making it possible to mate the connection improperly A sure indication of improper connection is a steady on condition of the drive s
23. ion IMI89 290 Installation And Application Instructions Installing The Computer Motherboard The motherboard is the main circuit board of the FX Series system computer Its components provide the processing and timing operations that are the heart of the computer s functionality The motherboard contains sockets and edge connectors that provide receptacles for memory components that store the data the computer needs to function properly and for the special purpose circuit cards that serve the many applications the computer may control Installing The Motherboard While adhering to the electrostatic discharge precautions detailed in Chapter One remove the motherboard from its static protection bag attach it at the top of the FX Series equipment cabinet using the supplied hardware Rear Edge Motherboard Mounting Of Cabinet Hardware typical oS ewe DO pe_mbrd2 cdr Installing The Motherboard Installing The Motherboard 2 1 Installation And Application Instructions Detailing The Motherboard Device Locations Once you have installed the motherboard and tightened its mounting hardware you should locate the device connections in preparation for making those connections as needed for your installation Power Supply Connection 9 Pin Serial Port Connector Parallel Data 3 5 Inch Floppy Disk Drive Connector IMI89 290 Hard Disk Drive Connector
24. k supplies voice ports one and two and the right jack supplies voice ports three and four Port one is the clock master port and all four ports synchronize on port one s timing therefore you must connect at least port one of the IVPC to a digital station port It is important to understand that the system does not automatically mark the four voice mail ports as such You must program the digital station ports to be voice mail ports before the VVP or Small Office software will function properly Installing The IVPC 9 1 Installation And Application Instructions IMI89 290 Strapping The IVPC You can install two or more IVPCs in the FX Series system computer provided you arrange for each IVPC to have its own I O address You set the I O address for the VPC by positioning straps on the IVPC board The strapping block is located at the corner of the card e o 0 D Le o D o o o D D o oO o a D o i o D o o e oo D o o D BOARD 4 o o o vvp strp cdr Placing The IVPC 1 0 Address Straps 9 2 Installing The IVPC IMI89 290 Installation And Application Instructions Installing The IVPC You must install the IVPC in the second ISA slot 1 Notice that the card has a wide metal connector bracket along one edge that contains the voice processing ports These are connections for telephony equipment You must remove from the common equipment cabinet the blank plate that covers the opening in front of the second ISA slot to make ro
25. nections that you must make to the CD ROM drive the power connection and the IDE data connection Connecting The CD ROM Drive Power Plug The computer power supply s multipurpose cable provides a plug that mates with the CD ROM drive power connector To make the power connection take the following steps 1 Locate one of the large white plugs attached to the power cable bundle There are several plugs available Choose the one that is most convenient to use 2 The power plug is keyed and it is not possible to connect it improperly Simply locate the hard drive s power connection at the rear of the hard drive assembly chassis and mate the connectors 6 2 Installing The CD ROM Drive IMI89 290 Connecting The CD ROM Drive IDE Data Cable The IDE data cables are the flat ribbon cables that connect between the computer s motherboard and the CD ROM drive The IDE cables are keyed on the motherboard end You can only connect them to the motherboard in one orientation This is not the case when you connect them to the drive assemblies At these connections there are two considerations that you must note 1 IDE ribbon cables provide several connectors along their length This allows one data cable to serve two drives when that need occurs In the case of the CD ROM drive in the FX Series system computer use the first connector on the cable that properly mates with the hard disk drive s IDE data connector Power Connect
26. om for the card s connector bracket Save the screw because you will need it later 2 The card s edge connector is keyed so you can only mate the card to the computer s motherboard connection in one orientation Align the card s metal connector bracket with the opening in the cabinet and mate the card to the motherboard s second ISA slot Do not force the card into the connection it should slide into place with gentle pressure when oriented properly 3 Once you have mated the card with the motherboard attach the card s metal connector bracket to the equipment cabinet using the screw removed in step 1 This action secures the card in place and provides a rigid connection for telephony equipment cables Typical FX Series System Computer Motherboard C DIMM BANK 2 SIMMA BANK _ Sim BANKT 3 SIMM2 BANK 0 gl COMI SMMIBANKO sg COM2 FDD HDDI O PRN HDD2 PCI Sio PCI Slot2 PCI Slot3 ISA Slot ISA Slot ISA Slot ISA Slot pe_mbrd7 cdr NOTE Your system s motherboard may differ from this typical example Refer to the literature included with your system for complete details Locating The Motherboard s IVPC Card Connection 82438VX 82438VX J11 Jl 25 JRI KBD Controller 0 z J22 b Installing The IVPC 9 3 Installation And Applic
27. ppy Disk Drive There are two cable connections that you must make to the floppy disk drive the power connection and the IDE data connection Connecting The Floppy Drive Power Plug The computer power supply s multipurpose cable provides a plug that mates with the floppy disk power connector To make the power connection take the following steps 1 Locate one of the smaller white plugs attached to the power cable bundle There are several available Choose the one that is most convenient to use 2 The power plug is keyed it is not possible to connect it improperly Simply locate the floppy drive s power connection at the rear of the floppy drive assembly chassis and mate the connectors Installing The Floppy Disk Drive 5 3 Installation And Application Instructions IMI89 290 Connecting The Floppy Drive IDE Data Cable The IDE data cables are the flat 3 5 Inch Floppy ribbon cables that connect between Disk Drive the computer s motherboard and the floppy disk drive The IDE cables are keyed on the motherboard end You can only connect them to the motherboard Hard Disk Drive sm sem in one orientation This is not the __SIMM2 BANK 0 case when you connect them to the NIAK 0 drive assemblies At these FDD HDD1 connections there are two uss PRN HDD2 Compact Disk Drive considerations that you must PCI Slot note PCI Slot2 1
28. r down the system bottom view and reverse the mating of the drive s IDE pe_drve3 cdr connection Orienting The IDE Connection 5 4 Installing The Floppy Disk Drive IMI89 290 Installation And Application Instructions Installing The Compact Disk CD ROM Drive The FX Series system computer provides a compact disk CD ROM drive assembly The CD ROM is a read only data device that stores large amounts of data typically one CD ROM stores up to 640 Mb of data Producers of software often make their application programs available on CD ROM because of its ability to store large files of data on one disk By including a CD ROM drive assembly the FX Series system computer provides a means for you to load large application programs without handling large quantities of floppy disks Installing The CD ROM Drive The CD ROM drive mounts in an opening on the FX Series common equipment cabinet that is to the right of the floppy drive hard drive cage opening and just above the front panel Mount the CD ROM drive in the common equipment cabinet by inserting it from the front of the cabinet into the opening and attaching it with the two supplied screws Mounting Hardware two places Common cd_drive cdr Equipment Cabinet CD ROM Drive Assembly Installing The CD Drive Installing The CD ROM Drive 6 1 Installation And Application Instructions IMI89 290 Connecting The CD ROM Drive There are two cable con
29. r the video card s connector O J22 ISA Slot I ISA Slot bracket Save the screw because ISA Slot I you will need it later pe_mbrd9 cdr NOTE Your system s motherboard may differ from this typical example Refer to the literature included with your system for complete details Locating The Motherboard s Video Driver Card Connection KBD Controller JRI a7 lee z 2 The card s edge connector is keyed so you can only mate the card to the motherboard connection in one orientation Align the card s metal connector bracket with the opening in the cabinet and mate the card to the motherboard s first PCI slot Do not force the card into the connection it should slide into place with gentle pressure when oriented properly 3 Once you have mated the card with the motherboard secure the card by attaching its metal connector bracket to the common equipment cabinet using the screw removed in step 1 This action secures the card in place and provides a rigid connection for the video monitor cable Installing The Video Card 7 1 This page remains blank intentionally IMI89 290 Installation And Application Instructions Installing The Serial Port Expansion Card The serial port expansion circuit card provides the computer with four additional serial ports Extra serial ports are very important when site requirements dictate that the FX Series system provide several different
30. s IMI89 290 10 Installing The Compact Disk CD ROM Drive ssssssss 6 1 Installing The CD ROM Drives 5 2 2 eevee nt omis oy eG hb ohne ede area 6 1 Connecting The CD ROM Drive sue oe pies Bees din none ve 6 2 Connecting The CD ROM Drive Power Plug 6 3 Connecting The CD ROM Drive IDE Data Cable 6 3 Installing The Video Cardin ones tete te 8 oles Rid PB ee ES 7 1 Installing The Serial Port Expansion Card 8 1 Installing The IV PC assur s sua seen een s ae a eR eel elon 9 1 Understanding The IV PC Characteristics 22 c2ch da een Beek Sees din Be 9 1 Installing The VPC essuie Rieti henan ia aa E a on TA G AES aa oai 9 2 Programming The Telephone System For IVPC Operation 9 4 Troubleshooting The IVPC Installation 9 4 Installing The Network Interface Card 10 1 Installing The Network Catd 9204 connue tea eee sus Bee Pow RSet ev andre os 10 1 iv Contents IMI89 290 Installation And Application Instructions Introducing The FX Series System Computer Components The FX Series system computer consists of the following elements motherboard power supply assembly disk drives includes hard drive 3 5 inch floppy drive and compact disk CD ROM drive individual application specific circuit cards
31. status light when you operate the drive Should the drive s status light remain on steady power down the system and reverse the mating of the drive s IDE connection Installing The CD ROM Drive 6 3 This page remains blank intentionally IMI89 290 Installation And Application Instructions Installing The Video Card The video card provides the interface between the FX Series system computer and the video monitor It provides standard resolutions and color depths to the Computer Telephony Integration CTD application software that is available for use with the FX Series system You must install the video card in the first PCI slot The illustration Typical FX Series System points out this location Install the Computer Motherboard video card in the manner described DIMM BANK 2 amp S 3 below SIMM4 BANK1 S Sis BANKT 3 1 Notice that the video card has a SIMM2 BANK 0 ana wide metal connector bracket _ SIMMI BANK 0 Le a q along one edge that contains a DD HDDT 8 R 15 pin female cable connector nn HOD This is the connection for the ps i Video Card PCI Slot E video monitor You must PCI Slot2 g remove the blank plate from the SEEE 8 0 PCI Slot3 common equipment cabinet that ISA Slot L is covers the opening in front of the first PCI slot to make room fo
32. tor between the AC power cord of the installed equipment and the AC outlet Normally you can use one multi outlet surge protector for both the telephony and computer portions of the FX Series system The equipment cabinet employs a fan cooled power supply do not block the air flow to this fan Per Underwriter Laboratory UL requirements DO NOT attach or secure the AC power cable to the surface of the mounting location in any manner AC Power Cable For FX Series System Computer ENI Rent s a rv ac_cord cdr Connecting The AC Power Cable Installing The Computer Power Supply 3 3 This page remains blank intentionally IMI89 290 Installation And Application Instructions Installing The Hard Disk Drive The FX Series system computer provides a hard disk drive assembly The hard disk drive mass storage unit used for storing large amounts of data for the Computer Telephony Integration CTI features that the FX Series system provides Installing The Hard Disk Drive The hard disk drive mounts in a drive cage along with the computer s floppy disk drive assembly The cage mounts in an opening at the top front of the FX Series common equipment cabinet Mounting The Hard Disk Drive In The Cage Mount the hard disk drive in the drive cage and attach it to the cage with the four supplied screws two on each side of the cage D p Mounting Cage 3 5 Inch Floppy Drive Hard Drive Mounting Hardware two
33. troducing Hard Drive Installing The 4 The FX Series System Computer 1 1 Hard Drive Mounting In The Cage 4 Connecting AC Power 3 3 Connecting Power I To The Internal Components 3 2 f Connecting The IDE Cable Connecting CD ROM Drive IDE Data Cable gae ROM BENS ara ae Connecting The IDE Cable Connecting The Floppy Drive 5 4 CD_ROM Drive Power Plug 6 3 IDE Cable Connecting The Hard Drive 4 3 Connecting The CD ROM Drive 6 2 Installing ee l Connecting The Eloppy Compact Disk CD ROM Drive 6 1 Disk Drive IDE Data Cable 5 4 Installing The Computer Motherboard 2 1 Connecting The Installing The Floppy Disk Drive 5 1 Floppy Disk Drive Power Plug 5 3 Installing The FX Series System Connecting The Floppy Disk Drive 5 3 Computer Power Supply 7a Connecting The Hard Installing The Hard Disk Drive 4 Disk Drive IDE Data Cable 4 3 Installing The IVPC 9 1 9 2 Connecting The Hard Installing The Motherboard 2 1 Disk Drive Power Plug 4 3 Installing The Multiple Serial Port Card 8 1 Connecting The Hard Drive 4 3 Installing The Network Interface Card 10 1 Installing The Power Supply 3 1 D Installing The Video Card 7 1 Detailine Th Internal Modem Strapping The Card
Download Pdf Manuals
Related Search