Cajun 16200F Stackable Switch
Contents
1. BE Co Emma fer HERE 7 md Terminators Two terminators are supplied with the P110 NMA Insert the two terminators into the lowest two connectors at the bottom of the stack as shown in Figure 2 Turn on the mains power to the stack by individually switching on each hub Connect the cables to the front panel ports P113F Stackable Switch Installation Guide 9 Chapter 2 10 Installation If both the P113F and the P110 NMA in the stack contain the latest software version as specified in the P113F Stackable Switch Release Note or higher the stack is now fully operational When a new version of agent software becomes available you should perform software download to benefit from the extra capabilities provided See Software Download on page 15 P113F Stackable Switch Installation Guide Chapter 2 Installation Rack Mounting P110 switches slot into a standard 19 inch rack Remove the rubber legs from the base of any switch that is to be rack mounted Place the switches in the rack and then connect the P110 Exoplane as follows 1 Snap open the ends of the front panel to reveal the fixing holes 2 Slot the switch into the r2. 3 Select Add to define a new Community name Select Delete to remove an existing Community name Select Update to change an existing Community name 4 Typethe appropriate SNMP Community name as shown in the example below Read Only Community Names are 1 public 2 3 4 5 Enter Read Only community name 24 char newname To review your changes select the List command To save your changes select Save the Session Repeat Steps 2 6 for any additional Community types Type 0 to return to the Communities main menu EST ON OI You must reset the agent after changing one or more Community names P113F Stackable Switch Installation Guide 31 Chapter 3 Configuration 6 Permanent Managers Permanent Managers define those management stations to which the agent will always send trap messages The P113F can be assigned up to ten permanent managers You must define your management console as a Permanent Manager If the agent and the permanent management stations reside on different networks ensure that the default IP Route has been assigned Each permanent manager is defined by its IP address To define a Permanent Manager 1 Select Permanent Managers from the Setup Main Menu This opens the Permanent Managers Menu shown below Permanent Managers Menu S W Version Slot s Refresh the screen Return to previous menu Save the Session Delete Update Enter your choice 2 Select Add to define
3. after the switch enters setup mode It shows the current configuration of the agent Description of Agent Parameters S W Version Slot HUB Type Visage 16200F Trap Community Name Read Write Communities qu 2 35 4 5 Interfaces Physical Address IP Address Netmask InBand Interface 00 40 0d 00 00 05 000 000 000 000 000 000 000 000 0x00000000 gt gt Enter 0 to return to the previous menu or CR to continue Press Enter to view the Setup Main Menu as shown The menu is different for a standalone and a stacked P113F In Standalone mode the menu is as shown below Setup Main Menu S W Version Slot d Refresh Screen Return to Previous Menu Reset the Module Software Download Agent Access Addresses IP Routes SNMP Community P113F Stackable Switch Installation Guide 17 Chapter 3 Configuration Permanent Managers Module Advanced Configuration Set Ethernet Ports parameters to their default values Enter your choice In Stack mode mode the menu is as shown below Items 5 6 and 7 above do not appear and 8 is different Setup Main Menu S W Version Slot Refresh Screen Return to Previous Menu Reset the Module Software Download Agent Access Addresses IP Routes Set Ethernet Ports parameters to their default values Enter your choice 18 P113F Stackable Switch Installation Guide Chapter 3 Configuration How to Navigate through the
4. switch OFF Standard 100BASE FX Ethernet packets Virtual LAN and priority information added to packets P113F Stackable Switch Installation Guide 13 Chapter 2 Installation 14 P113F Stackable Switch Installation Guide Chapter 3 Software Download to the On Board Agent The P113F contains an on board agent This agent does not use the same software package as the P110 NMA When a new version of the P113F software becomes available you should perform software download of the new version in order to benefit from the new capabilities provided Software download to the P113F is performed via a console terminal connected to the serial port on the rear panel of the P113F or via SNMP using a network management station The following sections explain how to download software to the P113F via a console terminal You must first upgrade the P110 NMA with the latest software version before adding or upgrading the P113F Stackable Switch or P117FR Stackable switch When working in a stack 2 3 or 4 switches a P110 NMA should be inserted into the topmost switch of the stack and the latest software downloaded separately to it The software is on the diskette that came with the P113F For instructions on how to download software to the P110 NMA see the P110 Installation Guide the download procedure itself is the same as that described below Connecting the Console Terminal Software download to a P113F switch is performed v
5. Exoplane which makes up a multi gigabit non blocking backplane The P113F can use Avaya flow control mechanism to eliminate packet loss An automatic fairness mechanism ensures that all ports gain fair access to the P110 Exoplane even at very high network utilization Congestion management works both on full and half duplex ports and ensures no packet loss should the buffers become saturated during peak load conditions A redundant power supply P110 BUPS may be used for additional fault tolerance Avaya switches are fully manageable using Avaya MSNM and may be monitored using the SMON Manager Switch Monitoring Application P113F Stackable Switch Installation Guide Chapter 2 Installation setting the DIP switches First set the DIP switches The position of the switches depends on the application The drawing below shows the default positions of the DIP switches on the rear panel of the switch Figure 1 The P113F Stackable Switch Rear Panel Showing the DIP Switches in their Default Positions Cm HOLIMS 3Sn 15 m ISI m cod m iod CE CXOH CB m ci Cm AST ij od e m EEE C All the DIP switches relate to the two 100 Mbps ports A detailed explanation of the DIP switches follows The DIP switches described below function o
6. P113F switch in the stack The P110 NMA must be in the top switch of the stack To ensure proper ventilation ensure that all empty P110 NMA slots in the stack are closed 8 P113F Stackable Switch Installation Guide 6 Chapter 2 Installation Connect switches using the P110 Exoplane cables as shown in Figure 2 A switch connects to its upper neighbor through two Exoplane cables and to its lower neighbor through another two Exoplane cables Make sure you securely fasten the cables to the connectors Cabling Requirements For correct operation the P110 Exoplane must be fully connected with all units powered up In case units are stacked the P110 NMA must be installed and connected to the Exoplane Failure to observe this requirement will cause the units to block all traffic on attached stations and segments When using the P114T or P114F in the stack make sure all switches in the stack are connected using P110 Exoplane cables part number 108362203 with white connectors and marked C S B of the type supplied with the new switch Extra cables can be ordered from your local Avaya representative For proper operation of the 100BASE FX ports the standard requires 62 5u Multimode fiber optic cables Figure 2 Rear view of a P110 switch stack showing how the switches are linked via the P110 Exoplane cables A P110 NMA resides in the uppermost switch P110 LR am NMA Ci P110 Exoplane Cables
7. Setup menus e All Setup menus conform to the following display conventions This symbol Thiiemhasasubmen This item has a sub menu to insert parameter values 122543 Denotes a sequence number To select an item from any menu etc type its sequence number Setup sub menus display the following standard functions This function Return to go back one menu level Previous Menu List the current values for the selected parameter Save the Save and store changes to the selected parameter and activate Session changes When saving the session the changes become active no need for reset and stored in the non volatile memory Reset the This is needed only when assigning IP address to the Agent In Agent other cases the Agent will activate new parameter values when the user choose the Save the Session option e If you forget to save changes or reset the agent when necessary the following warnings will remind you to do so before exiting the relevant sub menu of the Setup session This WARNING No save since last Type lt y gt to save parameter changes If you change Save y n type n all changes will be lost IP address was changed Agent must be reset in order to activate IP Reset the agent changes Reset may be done after each change or at the end of the entire Setup session P113F Stackable Switch Installation Guide 19 Chapter 3 Configuration Parameter configuration The following
8. manager communications The agent also stores a Netmask for each communication interface The Netmask defines which portion of the IP address represents the network ID and which portion represents the Host ID or network node Bits in the Netmask are set to one for all bits that correspond to the network portion of the IP address i e 255 in decimal Bits in the Netmask are set to zero for all bits that correspond to the Host ID of the IP address i e 000 For example if IP address 135 49 60 115 is assigned a Netmask of 255 255 255 000 it means that 135 49 60 defines the network in this case a subnet and 115 defines the actual node host on that network To assign an IP address and or Netmask 1 Select Agent Access Addresses from the Setup Main Menu This opens the sub menu shown below Agent Access Addresses Menu S W Version Slot lt CR gt Refresh the screen Return to Previous Menu Save the Session Interfaces IP Address Netmask InBand Interface 149 490 150 101 255 255 255 000 Oxffffff00 Enter your choice 2 Select InBand Interface The following prompt line will display InBand Interface IP address 149 490 150 101 netmask 255 255 255 0 gt gt gt Enter InBand Interface IP address 149 49 150 101 149 49 39 85 gt gt gt Enter InBand Interface netmask 255 255 255 0 255 255 255 0 26 P113F Stackable Switch Installation Guide Chapter 3 Configuration 3 Typ
9. port Full Duplex Half Duplex 1 FDX2 Full or Half Duplex port 2 Default FCI Flow control port 1 Not active Active Reserved for Future Use FC2 Flow control port 2 Reserved for Future Use ISL1 ISL Tagging port1 Not active Active ISL2 ISL Tagging port 2 Configuring the Module for Common Applications The table below describes how to set the DIP switches for common applications of the P113F Table 2 DIP Switch Settings for Common Configurations Switch Configuration 1 Configuration 2 Backbone link to Avaya products Backbone link to non Avaya LEB 200 or P113F products Set according to the application ON at both ends of link According to other side of link ON at both ends of link ON at both ends of link P113F Stackable Switch Installation Guide 7 Chapter 2 Installation Installing the P113F Stackable Switch The procedure for getting the P113F Stackable Switch up and running depends on whether the switch is to operate standalone or as part of a stack First attach the adhesive rubber legs to the base of the switch If the switch is to be rack mounted do not attach the legs Standalone Operation Plug n Play Getting the switch working is quick and easy 1 Connect the power cable to the switch 2 Connect the cables to the front panel ports The switch is now fully operational By default all ports will operate in half duplex mode To ensure proper ventilation ensure that the P110 NMA
10. port to 34 P113F Stackable Switch Installation Guide Chapter 3 Configuration which the management station is connected you will no longer be able to contact the P110 NMA agent and stack from CajunView This option does not affect Ethernet 10 Mbps ports of the P113F Other Ports in the stack can be changed to their default values via the equivalent option in the P110 NMA setup menu Set default values Confirm y n After confirming the resetting of a port s parameters you have to manually reset the stack See page 20 P113F Stackable Switch Installation Guide 35 Chapter 4 Terminal Connector Pin Assignments Figure 5 Terminal port RS 232 Wiring Connection to Console Terminal RJ45 N 2 Rx 3 Ix Fi J 5 Ground gt 5 P113F Stackable Switch Installation Guide 37 2003 Avaya Inc All rights reserved All trademarks identified by the or TM are registered trademarks or trademarks respectively of Avaya Inc All other trademarks are the property of their respective owners Document number 130003 Rev A
11. the latest available software You must first upgrade the P110 NMA with the latest software version before upgrading Switches The on board agent software is stored in flash memory and can be upgraded via software download using the TFTP protocol In the on board agent the flash memory contains two independent software versions the Basic and the Application version The Application version is the one that the P113F will use in normal operation If the Application version is found to be faulty the Basic version will be used instead Caution Download the Basic version only when the new Application version is working correctly This will ensure that if there is a problem with the application version the agent will be able to switch to a valid Basic version The TFTP Process The agent software file should be placed on a computer that can be anywhere on the network During the TFTP process the computer acts as the Server and the agent as the Client From the Terminal the user configures the agent with the IP address of the TFTP server the file name to be downloaded and the download destination bank The Agent then gets the specified file from the server During the download process the user can monitor the process status parameters by using the Monitor Software Download Process sub menuCajunView The agent remains fully functioning during the download process At the end of a successful download the whole switch stack resets autom
12. Installation Guide P113F STACKABLE ETHERNET SWITCH AVAYA Important Information SAFETY PRECAUTIONS CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK AND FIRE 1 e All servicing should be undertaken ONLY by qualified personnel The parts inside the unit CANNOT be serviced or repaired by the end user Please call your service representative for assistance Do NOT plug in turn on or attempt to operate a damaged unit Ensure that the chassis ventilation slots in the unit are NOT BLOCKED Replace a blown fuse only with the same type and rating as is marked on the safety label adjacent to the power inlet housing the fuse DO NOT operate the unit in a location where the maximum ambient temperature exceeds 50 sure to unplug the power supply cord from the wall socket BEFORE attempting to remove and or check the main power fuse PRECAUTIONS DE SECURIT AVERTISSEMENT POUR REDUIRE LE RISQUE DE CHOC LECTRIQUE ET D INCENDIE 1 2 3 Tout entretien doit tre fait UNIQUEMENT par un personnel de service qualifi Aucun l ment ne peut tre r par par un particulier NE PAS brancher allumer ou essayer de faire fonctionner une unit sur laquelle un doute existe quant a son bon fonctionnement S assurer que les ouvertures d a ration du ch ssis dans l appareil NE SONT PAS OBSTRUEES Remplacer un fusible d faillant UNIQUEMENT par un modele du m me type suivant les recommandations indiqu es sur l tiquet
13. a new Permanent Manager Select Delete to remove an existing Permanent Manager Select Update to change an existing Permanent Manager 3 Type the IP address of the Management station as shown in the example below Leading zeroes may be omitted 32 P113F Stackable Switch Installation Guide Chapter 3 Configuration Permanent Managers P110 NMA S W Version Slot Refresh the screen Return to previous menu 000 000 000 000 Enter manager address nnn nnn nnn nnn 135 49 50 115 4 Repeat Steps 2 3 for any additional permanent managers 5 To save your changes select Save the Session 6 0 to return to the Setup main menu Changes to the IP of a Permanent Manager do not require an agent reset P113F Stackable Switch Installation Guide 33 Chapter 3 Configuration 7 Module Advanced Configuration This option is not currently operational 8 Set Ethernet Ports parameters to their default values or 5 Set Fast Ethernet Ports parameters to their default values If the P113F is operating Standalone that is without a P110 NMA the displayed option is Set Ethernet Ports parameters to their default values If the P113F is operating with a P110 NMA or as part of a stack the option affects only the two Fast Ethernet ports Set Fast Ethernet Port parameters to their default values is displayed Other Ports in the stack can be changed to their default values via the equivalent option in the P110 NMA s
14. ack Insert the switches into the rack so that the switches in a logical stack lie directly on top of each other Ensure that the P110 screw holes are aligned with the rack hole positions exactly as shown in figure 3 Stacking them in this way will allow the switches to be easily connected using the Exoplane cables 3 Secure the switch in the rack using the screws Use one screw on each side Do not overtighten the screws to avoid damaging the plastic 4 Connect the P110 Exoplane cables as described above and as illustrated in Figure 2 5 Snap closed the hinged ends of the front panel Figure 3 P110 rack mounting arrangement Use only one of the two holes e Hole Screw hole in P110 Screw position P113F Stackable Switch Installation Guide 11 Chapter 2 Installation Diagnostics Table 3 and Table 4 explain the meaning of the P113F Stackable Switch diagnostic LED indicators Figure 4 The P113F Stackable Switch Front Panel LEDs and Buttons 100 M oN p 1 2 3 4 5 6 11 12 13 14 T RI O 0000 0000 40 gt 0000 0000 N R 9 10 15 16 17 18 PWR NMA RED OPR LNK COL Tx Rx FDX FC ISL OOOO O0 00 O00 P Table 3 Meaning of the P113F Stackable Switch Front Panel Buttons gm 12 The buttons determine what function will be displayed by the 18 Port LEDs the top two rows of LEDs The seven Function LEDs ab
15. atically Software Download Procedure Before starting the download procedure do the following 1 Ensure that the supplied agent software file resides on a computer with TFTP server capabilities 2 Ensure that the file is accessible to the agent Contact the agent from the TFTP server by typing ping ip address of agent P113F Stackable Switch Installation Guide 21 Chapter 3 Configuration Download software to the agent as follows 1 Select Software Download from the Setup Main Menu This opens the Software Download menu shown below Software Download Menu Using TFTP IP S W Version Slot lt CR gt Refresh the screen Return to Previous Menu Save the Session TFTP Server and File parameters Start Software Download process Monitor Software Download process Enter your choice 2 Select TFTP Server and File parameters from the Software Download menu This opens the menu shown below TFTP Server IP address 000 000 000 000 File Name Destination Flash B Application Enter Server IP address 000 000 000 000 135 49 60 115 Enter File Name c mng agents v_16200 Enter Destination 1 Flash A Basic 2 Flash B Application 2 3 Type the IP address of the TFTP server and press Enter Type the File Name of the agent software and press Enter Ensure you enter the full path for the file For example c agents v_16200 for a PC server users david v_16200 for a UNIX server However if r
16. e the new IP address as shown in the example above and press Enter Leading zeroes may be omitted 4 After the IP address is accepted the Netmask prompt is automatically displayed The prompt has a default value based on the IP address 5 Type the new Netmask value in the correct format or press Enter to accept the default value 6 Type 0 to return to the main menu Changes to IP Addresses and Netmasks require you to reset the agent You may reset the agent now or at the end of the entire Setup session P113F Stackable Switch Installation Guide 27 Chapter 3 Configuration 4 IP Routes When the P113F is connected to one side of a router on one network and the file containing the new software is located on the other side of the router on a different network you must set up a communication path via the IP Routes parameter An IP Route determines which gateway i e router will be used to communicate with the P113F Whenever the agent sends a packet to a management station that does not reside on the same network the agent searches an internal table to determine via which router the packet should travel Part of this internal table is built from the data you enter for the IP Routes parameter The IP Routes parameter correlates host or network destination addresses of management stations with gateway addresses You may define multiple IP Routes from agent to management station As the agent searches the IP Routes table
17. etup menu Set Ethernet Ports Parameters to their Default Values This option appears when the P113F is operating standalone It returns all Ethernet port parameters such as VLAN number port mode and administration status to their default values It does not affect agent access parameters such as IP addresses IP Routes and Permanent Managers This option also sets 100 Mbps ports on the P113F to their default values You may wish to reset all ports for example to move the product from a testing to real environment or the changed ports are not operating as expected Ifyou reset all the ports in a working system you will lose all the environment settings configured to each P110 stack port The ports will then not operate properly in your environment Perform the resetting of a port s parameters 90 seconds after power up or a reset of the stack Set default values Confirm y n After confirming the resetting of a port s parameters an automatic reset will be performed Set Fast Ethernet Port Parameters to their Default Values This option returns the Fast Ethernet port parameters such as VLAN number port mode and administration status to the ports default values It does not affect agent access parameters such as IP addresses IP Routes and Permanent Managers Use this option if for example in using CajunView you accidentally disabled the port to which the management station is connected If you disable the
18. f the download process P113F Stackable Switch Installation Guide 23 Chapter 3 24 Configuration 9 Type 0 to Return to previous menu 10 To save your changes select Save the Session 11 Type 0 to return to the Setup main menu P113F Stackable Switch Installation Guide Chapter 3 Configuration Troubleshooting Software Download The following are Activity Status messages that can appear during software download their meanings and what you should do about them Table 5 Troubleshooting Software Download Activity Status Description Suggested action message File format unknown Ensure that the correct agent software file is being downloaded to the agent File not found Failure of TFTP Get Type in the correct path and filename Server is unreachable Failed to find the Type in the correct TFTP Server IP server after 1 minute address Ensure the server is accessible to the agent by typing ping ip address of agent Alternatively if a router is required to reach the server type in the router address from the IP Routes menu as explained on page 28 P113F Stackable Switch Installation Guide 25 Chapter 3 Configuration 3 Agent Access Addresses This parameter stores IP addresses for the agent s communication interfaces The interface addresses facilitate communication between the agent and the management station By assigning an IP address to the agent interface you make that interface available for agent
19. ia a console terminal connected to the serial port labeled Console on the P113F To connect the P113F to a console terminal 1 Turn on the VT52 or VT100 terminal or PC in terminal emulator mode and set its communication parameters to Baud Rate 9600 bps Start Bit 1 Data Bits 8 Stop Bit 1 Parity none Refer to your console terminal s user manual for instructions on how to set these parameters 2 Insert the RJ 45 connector of the cable into the Console port of the P113F cable pinouts can be found in the Appendix to this guide 3 Insert the other end of the cable into the terminal s RS 232 port 4 Press Enter to verify that the cabling process was successful P113F Stackable Switch Installation Guide 15 16 Chapter 3 Configuration Software Download Summary Below is a checklist of the procedure for successfully configuring a P113F for SNMP management Instructions for each item in the list can be found in the pertinent sections of this guide Y If necessary enter an IP address for the P113F and reset the switch Y Ifyou re using routers set up a default router address Y Perform software download P113F Stackable Switch Installation Guide Chapter 3 Configuration setup Menus Setup Main Menu A series of menus guides you through the configuration process Underlined spaces in the example screens represent variables A standalone P113F automatically displays the first screen of the setup session
20. it will select the gateway that was added last If that gateway is unavailable it will proceed to the gateway added before the last one and so on You may also define a default gateway for all management stations rather than define a specific gateway for each possible destination If the agent cannot find a particular network or host destination address in its IP Routes table it will use the default gateway the default gateway is correlated with destination address 000 000 000 000 If the agent cannot find a particular network or host destination address and no default gateway has been defined the packet will not be sent To define an IP route you must supply e The IP address of the station with the agent software or the network address of the net not subnet to which the station is connected e The IP address of the gateway router through which management packets will travel To define and IP Route 1 Select IP Routes from the Setup Main Menu This opens the IP Routes sub menu shown IP Routes menu S W Version Slot Refresh the screen Return to previous menu Save the Session List static routing table 28 P113F Stackable Switch Installation Guide Chapter 3 Configuration Delete Enter your choice 2 Select Add to define a new IP Route Select Delete to remove an existing IP Route 3 Type the destination address of a host IP address of the management station or a network IP of manageme
21. k must be Reset after changing Half Full Duplex mode FC Flow Control FCI is for port 1 and FC2 is for port 2 When this switch is in the ON position the switch uses a proprietary Avaya mechanism to prevent packet loss on the link due to congestion in full duplex mode ISL Inter Switch Link Tagging ISL1 is for port 1 and ISL2 is for port 2 ISL Tagging expands Virtual LANs and Priority across the backbone This switch should be set to ON when you wish to make two Avaya switches linked by the P113F act as a single logical entity When set to OFF ports will send standards based Fast Ethernet 100BASE X packets If the settings of an existing P110 stack are changed the stack must be reset Press and hold both buttons on the front panel simultaneously for a second or more to reset the entire P110 stack In a reset all LED indicators turn on Pressing reset does not affect configuration settings Once you have set the switches you may proceed with the physical installation of the switch P113F Stackable Switch Installation Guide Chapter 2 Installation Table 1 DIP Switches on the P113F Stackable Switch Down OFF UP ON RE Reserved for Future Use LSV Latest software version Use the Basic Use the latest software version in Application Bank A agent software in Bank B Default USE Selection of operational Ignore switches Use Use switches SWITCH mode management settings Default 2 FDX1 Full or Half Duplex
22. nly when the USE SWITCHES switch is in the ON position e LSV Latest Software Version The agent can use either the latest downloaded software the Application version or a Basic version e USE SWITCHES Selects whether the 100Mbps functions will be controlled by the DIP switches or from the management station When set to ON 100 Mbps switch settings are determined by the DIP switches and can only be monitored but not changed by the console When set to OFF the DIP switch settings are ignored and the 100 Mbps port functionality is controlled from the console via the P110 NMA Set to ON when you don t have SNMP management or when you want to ensure that the settings will not be changed e R12 Redundancy Setting this switch to ON enables redundancy In this case port 1 is active and port 2 is redundant In the event of link failure switchover to port 2 is automatic Where redundancy is not desired set this switch to OFF and both ports will operate normally P113F Stackable Switch Installation Guide 5 Chapter 2 Installation HDX Full Half Duplex HDX1 is for port 1 and HDX2 is for port 2 When this switch is in the ON position the switch operates in Half Duplex mode When the switch is in the OFF position the switch operates in Full Duplex mode Full Duplex gives a throughput of 200 Mbps In Full Duplex mode no repeaters are allowed in the path Half duplex operation gives a throughput of 100 Mbps The stac
23. ns for getting the P113F Stackable Switch and P110 stack up and running e Software Download Step by step guide to downloading a new software version to the P113F on board agent e Appendix Pin Assignments for the console RJ45 connector P113F Stackable Switch Installation Guide 3 Chapter 1 Description Description The P113F Stackable Switch is part of the Avaya P110 Switching System family of switches The family is composed of high performance stackable switches which may be used singly or stacked in any combination to make up a multi protocol non blocking scalable switch The P113F has 16 Ethernet 10BASE T ports and two Fast Ethernet 100BASE FX ports The 10 Mbps ports are typically used for workgroup connectivity while the two 100 Mbps ports can be used as full duplex uplinks to an Avaya switch The 100 Mbps ports can transfer Virtual LAN and priority information by setting them up as Inter Switch link ISL ports All ports can run at full or half duplex Ethernet and one of the 100 Mbps ports can be defined as redundant port These functions are configured using DIP switches A redundant power supply may be used for enhanced fault tolerance The P113F can operate standalone or as part of a stack A stack can be made up of any combination of two three or four P110 switches and up 32 000 MAC addresses per stack are supported A stack requires a P110 NMA to link the switches The units are physically linked using the P110
24. nt network as shown in the menu below and press Enter For a default gateway leave the destination address as 000 000 000 000 IP Route parameters menu S W Version Slot d Refresh the screen return to the previous menu Destination Gateway 154 32 74 12 149 43 63 123 154 32 74 53 321 12 69 54 000 000 000 000 149 43 63 123 000 000 000 000 000 000 000 000 000 000 000 000 000 000 route destination address nnn nnn nnn nnn 150 61 23 18 route gateway IP address nnn nnn nnn nnn 135 49 50 1 Type the Gateway IP address address of the router and press Enter To review your changes select the List command To save your changes select Save the Session Type 0 to return to the Setup main menu to IP Routes do not require you to reset the agent NO gU P113F Stackable Switch Installation Guide 29 Chapter 3 Configuration 5 SNMP Community An SNMP community name is a local identifier up to 24 alphanumeric characters used by the SNMP protocol to control access to the management agent Each agent is assigned a community name which the management station must know in order to communicate with the agent The P113F has a default community name of public All management stations can communicate with agents in the publie community If you change this community name or add a new community name to the agent you must also reconfigure the management station s that will be communicating with the agent Ify
25. ou change the public community the management station will not be able to communicate with the agent until the management station has been configured with the new community name The P113F accommodates three types of SNMP community names e Read Only The agent accepts and processes only SNMP Get commands from management stations with a read only community name The communities table can include up to five read only community names e Read Write The agent accepts and processes SNMP Get and Set commands received from management stations with a read write community name The communities table can include up to five read write community names e Trap The agent sends Traps to a management station within this community Only one trap community name may be defined for the agent To update the SNMP Community table 1 Select SNMP Community from the Setup Main Menu This opens the menu shown below SNMP Community Menu Version Slot Refresh the screen return to the previous menu Trap Community Read Only Community Read Write Community Enter your choice 30 P113F Stackable Switch Installation Guide Chapter 3 Configuration 2 Select the type of community you want to change This opens a Community specific menu like the Read Only menu shown below Read Only Community Menu S W Version Slot Refresh the screen return to the previous menu Save the Session Delete Update Enter your choice
26. ove the Select buttons show which function is currently displayed by the Port LEDs The Port LEDs can display either Link Collision Transmit Receive Full Duplex Flow Control or ISL If for example the Link LNK LED is lit then LEDs 1 to 18 will display the Link status of every port Press the left or right button to toggle the Port LED display between functions Press and hold both buttons simultaneously for a second or more to reset the entire P110 stack In a Reset all LED indicators turn on Pressing Reset does not affect configuration settings P113F Stackable Switch Installation Guide Chapter 2 Installation Table 4 Meaning of the P113F Stackable Switch front panel LEDs LED Indicator Power Mains power not connected Mains power connected Working on back up power supply Agent OFF No agent in switch ON Switch contains an active agent RED REDNMA Reserved for future use CPU OFF CPU is OK Operation Blink CPU is faulty Redundancy No redundancy ports 1 2 Port 1 active Port 2 active Function LED Port LED Link status Port Disabled Port is enabled and link is OK Blink once Link Test Fail Blink twice Partition Collision No Collision Collision occurred on line Transmit to No activity line Data transmitted Receive OFF No activity from line ON Data Received Half Full OFF Half duplex connection to port duplex ON Full duplex connection to port Flow Reserved for future use control Inter
27. sections provide step by step instructions for configuring each parameter lt CR gt Refresh The Screen Type Enter to clear the screen and re display the current displayed Menu 1 Reset the Module If you have changed certain parameters of the P110 NMA P113F or other switches in the stack you must reset the agent before you exit the Setup session The following lists the resets you must initiate and the resets performed automatically by the agent Resets You must Initiate Resets Performed Automatically by the Agent Change in the Use switch The first time you set VLANS or any other DIP switch after setting the 100Mbps port parameters in the P113F to their default values After setting Ethernet ports or all ports to their default values After a port mode change in one of the 100Mbps ports in the P113F Resetting the agent does not affect any other parameters You will be asked to confirm the reset before it is executed Reset the Agent Confirm y n The preferred and most reliable method of ensuring that configuration changes are saved is by resetting the agent through the Setup menu rather than by pressing the Reset button on the agent panel 20 P113F Stackable Switch Installation Guide Chapter 3 Configuration 2 Software Download General When you receive the P113F it s on board agent comes pre loaded with fully functioning software You should make sure that all units contain
28. slot is closed The P113F contains an on board agent If you want to upgrade the on board software to a higher version see the Software Download section on page 15 Stacking Operation To make the P113F work as part of a stack and to give SNMP management capabilities to a single P113F a P110 NMA with the correct software version is required See the P113F Stackable Switch Release Notes for the required version To check what software version you have see the agent configuration window in CajunView or see the setup main menu of the P110 NMA 1 Before adding a switch to the P110 stack turn off the main power to the stack by individually switching off each hub 2 Place the P110 NMA in the top switch of the stack 3 Ifthe P110 NMA and the P113F on board agent contain the latest software version go to step 5 4 Ifthe P110 NMA does not contain the latest agent software you should perform a software download of the latest version The software is on the diskette that came with the P113F Download is performed via TFTP using a Terminal console or via the timed Download application from your management station details can be found in the P110 NMA installation Guide The download procedure itself is the same as that described in the Software Download section on page 20 If the P113F on board agent does not contain the latest version perform the download as described in Software Download to the On Board Agent on page 15 5 Place the
29. te de securit pos e dans le logement du fusible NE PAS faire fonctionner l appareil dans un endroit o la temperature d passe les 50 C S assurer de d brancher l alimentation lectrique AVANT toute manipulation sur le fusible principal SICHERHEITSVORKEHRUNG ACHTUNG ZUR VERHINDERUNG DES RISIKOS VON ELEKTRISCHEM SCHLAG UND FEUER 1 Die Ger te enthalten keine Bauteile die au erhalb des Avaya Servicezentrums gewartet oder repariert werden k nnen Die Wartung darf NUR von qualifiziertem technischem Personal durchgef hrt werden NIEMALS ein besch digtes Ger t einschalten oder versuchen es zu bedienen Vergewissern Sie sich dass die Chassis Ventilations ffnungen des Ger tes NICHT BLOCKIERT sind P113F Stackable Switch Installation Guide 1 Preface Safety Instructions Austauschen einer durchgebrannten Sicherung NUR mit der gleichen Sorte und Belastbarkeit wie sie auf der Sicherheitsaufschrift markiert ist Die Aufschrift befindet sich neben der Stromzufuhr wo sich auch der Sicherungskasten befindet Bedienen Sie das Ger t NICHT an einer Stelle an der die Umgebungstemperatur 50 C bersteigt Ziehen Sie das Netzkabel raus BEVOR Sie versuchen die Hauptsicherung zu kontrollieren oder auszutauschen P113F Stackable Switch Installation Guide Chapter 1 Overview This guide is divided into four main sections e Overview A general description of the features of the P113F Stackable Switch e Installation Instructio
30. unning TFTP in secure mode from a Solaris station and the agent file v_16200 is in the secure directory default is tftpboot simply write the filename without the full path 22 P113F Stackable Switch Installation Guide Chapter 3 Configuration 4 Type the destination memory location of the software The Application version is stored in Flash memory bank B and the Basic version is stored in memory bank A Caution Do not download the Basic version until the Application version is working correctly 5 If you wish to download a new Application version type 2 Flash B as the destination Press Enter 6 To save your changes select Save the Session 7 Select Start Software Download process You will get a warning and a confirmation prompt as follows Warning Perform Software Download Confirm y n 8 Keep track of the progress of the software download by selecting Monitor Software Download process Press Enter to get an update of the download process as shown below Agent Software Download Monitoring Screen S W Version Slot TFTP Server IP address 135 49 60 115 File Name c agents v_16200 Destination Flash Bank B Application Download State tftp running ip Activity Status Testing Download Size lt CR gt Refresh the screen 0 Return to previous menu Enter your choice The Activity Status displays Testing Erasing Flash or Downloading depending on the stage o
Download Pdf Manuals
Related Search