EZ-LP Desktop Label Printer USER`S MANUAL
Contents
1. Enter on your computer keyboard to send the settings file to the printer USB A Port Changing Printer Settings Using a USB Flash Drive MAMM 6 Create a folder on the USB flash drive at the root level named Cognitive Inside the Cognitive folder create a folder named Settings Place the desired CPL text files into the Settings folder Turn the printer ON and verify the POWER and READY lights are green Insert the USB flash drive into the USB A port onthe back ofthe printer READY light will flash guickly while the file loads When the READY light remains solid green remove the USB Flash Drive Loading Firmware Using a USB Flash Drive 1 2 3 4 5 6 Create a folder on the USB flash drive at the root level named Cognitive Inside the Cognitive folder create a folder named Firmware Place the desired firmware revision into the Firmware folder Turn the printer ON and verify the POWER and READY lights are green Insert the USB flash drive into the USB A port on the back of the printer The READY light will flash red during firmware installation When READY light remains solid green turn the printer off and remove the USB Flash Drive Loading Formats Using a USB Flash Drive m Na Create a folder on the USB flash drive at the root level named Cognitive Inside the Cognitive folder create a folder named Objects Place the desired Stored Label Formats into the Objects folder Turn the printer on and verify2. the POWER and READY lights are green Insert the USB flash drive into the USB A port on the back of the printer READY light will flash red during firmware installation When READY light remains solid green turn the printer off and remove the USB Flash Drive HELPFUL TIP PRINTER WILL LOAD OBJECTS FILES IN ALPHABETICAL ORDER 27 IMPORTANT DISCONNECT POWER PRIOR TO CLEANING THE EZ LP WARNING INCORRECTLY CLEANING PRINTER WILL CAUSE PERMANENT DAMAGE AND VOID WARRANTY COGNITIVETPG RECOMMENDS USING A CERTIFIED CLEANING PEN FOR CLEANING THERMAL PRINTHEAD For optimal printhead performance CognitiveTPG recommends cleaning the interior components printhead platen roller media sensor peel bar if installed ribbon and media paths every 20 000 inches 508 m The thermal printhead should be cleaned every 5 000 inches if pre printed labels are used Proper maintenance reduces replacement costs by extending the life of the printhead and improves the performance ofthe printer Clean the exterior ofthe printer and the media tray using a lint free cloth and if necessary a mild detergent solution 1 Open the print mechanism 2 Gently clean the printhead A platen roller B and media path using a CognitiveTPG approved cleaning pen card or a soft lint free cloth saturated with 99 isopropyl alcohol EZ LP Cleaning Supplies Part Size inches Items pe
3. EZ LP Desktop Label Printer USER S MANUAL EZLP UG00000 Rev B 03 30 2009 Copyright 2009 CognitiveTPG CognitiveTPG and EZ LP are trademarks of ATSI Holdings Inc Microsoft and Windows are trademarks of Microsoft Corporation EPL is a Zebra trademark and ZPL is a registered trademark of ZIH Corp Other product and corporate names used in this document may be trademarks or registered trademarks of other companies and are used only for explanation and to their owner s benefit without intent to infringe All information in this document is subject to change without notice and does not represent a commitment on the part of CognitiveTPG No part of this document may be reproduced for any reason or in any form including electronic storage and retrieval without the expressed written permission of CognitiveTPG All program listings in this document are copyrighted and are the property of CognitiveTPG and are provided without warranty To contact CognitiveTPG Write email or call CognitiveTPG 25 Tri State International Suite 200 Lincolnshire IL 60069 E Mail marketing cognitivetpg com Telephone 847 383 7900 Toll free 800 732 8950 Fax 847 383 7949 Technical Support 800 732 8950 extension 4 Chapter 1 Hiner oQuicnon een 4 Meeme ee en 4 Package Contents a saama aa 4 Operating Environment an 4 Printer Feature Overview asssssensenensenenensenensenenensenensenenensenensenensenenensenen 5 Front Re
4. OULD DAMAGE THE PRINTER NOTE IF YOUR COMPUTER IS CONNECTEDTO THE INTERNET USE THE GET LATEST FIRMWARE FROM COGNITIVETPG BUTTON THIS ACTION WILL ALSO LOAD CURRENT FONTS UPDATE WILL TAKE A FEW MINUTES Firmware Upgrade 1 Select the Firmware Upgrade tab 2 Click the Select Firmware File button 3 Select the appropriate Firmware file and click Ok 4 Clickthe Update Firmware button Script Editor Use the Script Editor in CognitiveTPG Printer Administrator to send programming language code to the printer The EZ LP printer will not print CPL label formats but will recognize CPL based printer setting commands For more information on programming CPL please refer to the CPL Programmers guide located on the CognitiveTPG Web site www CognitiveTPG com 24 TOGAPCAL 1 40 0 10 TeagVar se alters Videb CO ElspeThrer rz WLTiieE Bar 767 230 Gap Tores 25 Chapter 5 Advanced EZ LP Features Making Configurations Changes Using DOS Commands 1 Power off your current desktop label printer and disconnect the communication cable 2 Connect Power supply to EZ LP and plug into wall Do NOT turn on EZ LP at this time 3 Connect preferred interface cable to EZ LP and connect to PC 4 Turn on the EZ LP printer 5 Opena text file editor such as Notepad START gt All Programs gt Accessories gt Notepad 6 Typeinthe desired code see examples below and save the file Note t
5. Soge Ester aas 2 font 4 Vector Port doean verg frt Nee oy Aral Vector Port ven vety toe ru u feet vector Port A Comet 3 ret ma Aa Ri ree Mis nn Org 3 rhe reese n ver 3 ree au me Gegen 3 Hit wore n Cte 3 rae are me Ott I View lt lt me Cope 3 thew owe ma Comet x Min ns met Niet en mr u Comet 7 Fuss vn an Cree 3 nu m M t rt Has mim N Cpe Hew 15150 cn wei Comet 3 Pliit ns Kom 1083 Ott 9 Hee ro t 2 fo aa Nye 616 t 14 Ot 5 Hs un at 4 Ms Chet 7 Fest m toats wt Otea Het ne vi 13 Creat foe um ver w tmt 6 Hawt ab n on et Hoot wo EEE tan 1 on Chet 5 Hot Aa GP S Lan pe cepe ree 0 laduma EASI Kain Pit tet W Not 9 MEN Cyri P Cet u me on viet age OR Greek is Otet 38 Fae 00 odaga 88574 Turus rn One 38 Fee wo adeta 125 Wades Later wn Otea Faa 00 age 1251 Windows C on Cet 5 Hin u Siap 125 Winden Geek Pr nt nu xo oe ae 1294 Winders Trib pa etn n on 100 00 JAN 2 tend Comets t Printer Coto bemctes Cepte perse Loading Fonts and Objects 1 Select the Fonts and Objects tab 2 Click the Load Objects to Printer button 3 Selectthe Font or Object to be stored and click Ok Deleting Fonts and Objects 1 Select the Fonts and Objects tab in CognitiveTPG Printer Administrator 2 Highlight the Font Object or Graphic to be deleted 3 Click the Delete Selected Objects button 22 Profile Management Manage the settings of the EZ LP u
6. USB connection a New Hardware Wizard may appear on screen Click Cancel and continue with step 8 below If using Serial or Parallel connection continue with the next step Print from your application you are finished If you wish to install EZ LP and assign it to another driver continue to the next step In Microsoft Windows click the Start menu choose Printers and Faxes and Add printer The Add Printer Wizard will appear Click Next Add Printer Wizard Welcome to the Add Printer Wizard Ths wird hebs pou wnutall a painter or make porter connectors r f you have a Plug and Play printer that connects W Hwch a USB pert foe arg othar het pk pot such at IEEE 1394 eirared and so onl you da na need to une thes waard Ock Cancel to close the witeed and then plug the printer s cable info pour Computes of port the printer toward pout computer s rimed pof axi han De orin on Windows wi aulomaboalu natal the parher for you To coria click Nee 10 Select Local printer attached to this computer and click Next ee Add Printer Wizard Local or Network Printer The wead reed to brow whch type of partas fo set up Select he option that dereiat he partes you wart to use ETTE TT Ardompoaly detect and natal my Plug and Ply panter Anarchie o a printer ettached ko anche compde i To pet up a neterork ger Dud i net attached ka a pari semen LJ usete Locs preter tion sts st ori 11 Select Use the
7. ake sure media is face up out of by flexing out media holders and front of printer and securely latch positioning plastic protrusions into printhead closed media roll core 9 Lower dust cover and continue to Self Testing Self Testing NOTE AFTER PRINTING A SELF TEST PRINTER IS IN HEXIDECIMAL DUMP MODE CYCLE PRINTER S POWER TO RETURN TO NORMAL OPERATION 1 Press and hold the feed button while 2 Release feed button when printing turning printer ON begins and printer will conduct a self test and print a configuration label 3 Power OFF printer to end 4 Power ON printer for normal hexadecimal dump mode operation IMPORTANT IF BAUD RATE BETWEEN HOST SYSTEM AND EZ LP ARE NOT EQUAL PRINTER WILL NOT PRINT EZ LP DEFAULT BAUD RATE IS 9600 AND DEFAULT SERIAL PORT SETTINGS ARE 9600 BAUD 8 BITS NO PARITY 1 STOP BIT Chapter 3 Installing the EZ LP Installing Printer via Serial Parallel or USB as a Replacement for Legacy Printer 1 Ri Print configuration label or record your current printer s settings including the driver port setting Power off your current desktop label printer and disconnect interface cable Connect power supply to EZ LP printer and plug into wall Do NOT turn on the EZ LP at this time Connect preferred interface cable to EZ LP and connect to PC Turn on the EZ LP printer If using a
8. ar VIER une laamas 5 Inside NIS aaa aal 6 Chapter 2 Printer Installation samma 7 Setting up the EZ LP PAIDEST nn 7 Connecting the Interface and Power Cables 7 Loading Melanie 8 Sell Teen ee 10 Chapter 3 Installing the EZ LP mmusenensenseneeneneenennensenenneneenennennenenet 11 Installing Printer via Serial Parallel or USB as a Replacement for Legacy Printer scssscssscsscsecssececssessessecsscseeseees 11 Chapter 4 Installing CognitiveTPG Printer Administrator and Print Driver aaa 14 Windows Driver Installation sssesssscsscssecsscsscssecsscssessesecseerscsees 15 Installing Printer via USB sssssseeessssseressssssseeessssseressssserees 15 CognitiveTPG Printer Administrator Utility 17 Connection SettiNgS anna 17 PPA MEST SEIUNG ass 18 Label PosSOMIM Gitta 20 Profile Management re 23 Firmware Upgrade nenn 24 SCHULE AND en ee TRO 24 Chapter 5 Advanced EZ LP Features ussessessessensensensenennsnnsenseneneennennenneneen 26 Making Configurations Changes Using DOS Commands 26 USB A POTT eek 26 Chapter 6 Cleaning and Maintenance sessesssseessessesssseressseerosseressseerosee 28 Cleaning the Printer ccsssssscsssssssssssesssecsecssssssessssessecsecsssecssessenees 28 Cleaning the Thermal Printhead and Platen ms 28 Cleaning Supplies AARMA 28 Chapter 7 Troubleshooting amp Default Settings sssssssssssssresssssssssss
9. ation and the printer will automatically attempt to recalibrate in the event an index mark is not detected Auto Top Of Form Check and Apply Enable Automatic TOF and the printer will feed a label when the printer is turned ON or the printhead is latched Indexing Indexing indicates to the printer the index type of the media being used The Indexing On check box must be checked when using Bar Gap or Notch style indexing Uncheck the Indexing On box when using continuous media Label Presentation Label presentation advances media out of the printer after printing a label and then retracts the media prior to printing the next label Advance Distance the media advances after printing a label Retract Distance the media retracts prior to printing a label Time Amount of time in seconds the label remains presented prior to retracting 21 Top of Form Adjust Top of Form TOF sets the top ofthe label with relation to the print head Increasing the TOF value moves the printed text down the label Decrease the TOF setting to move the printed test up the label Shift Left Shift left moves the printed image left across the label Fonts and Objects The Fonts and Objects tab lists the Fonts Formats and Graphics currently stored in the printer Gi Cae vinker Ad runditraten vi 53572 leizi T Painter Sisha u o Carrin Setting Prnter Setings kabel Prutorng FF Th pete agror Fremare urgat
10. complete installation 16 NOTE WHEN PRINTER IS PROPERLY CONNECTED COGNITIVETPG PRINTER ADMINISTRATOR WILL DISPLAY CONNECTED IN A GREEN BOX IN UPPER RIGHT CORNER NOTE THE EZ LP DEFAULT BAUD RATE IS 9600 CognitiveTPG Printer Administrator Utility Connection Settings Connecting Via USB 1 Select the System Printer Connection radio dial 2 Select the appropriate printer from the Printer Name drop down menu 3 Click Connect HELPFUL TIP PRINT ASELFTESTTO DETERMINE PRINTER S CURRENT SETTINGS ASELFTESTCAN BE PERFORMED BY HOLDING THE FEED BUTTON WHILE TURNING PRINTER POWER ON CONTINUE TO HOLDTHE FEED BUTTON UNTIL SELF TEST PRINTS Connecting Via Serial 1 Select the Use Serial Connection radio dial 2 Selectthe Com port to which the printer is connected 3 Select the printer s baud rate setting Connecting Via Ethernet 1 Select the Use Network Connection radio dial 2 Inputthe printer s IP Address if static IP Address is to be used otherwise with DHLP enabled your server will assign an IP Address to the printer 3 Inputthe printer s RTEL port number Serial Connection Parameters e Baud Rate XON XOFF Buffer Size Buffer Overflow Ethernet Connection Parameters e IP Address e Net Mask e Gateway DHCP e LPD RTEL e RTEL Port Ethernet Text Buffer Printer Settings Print Soeed The Print Speed value sets th
11. e printing speed of the printer Low 2 inches per second Normal 3 inches per second High 5 inches per second 18 T erter Staha E e ia Cermin Settings FEE SAS Lte Peutioring Fonts ard Objects Peofity Naragerrant Frmmart Urgaas Saige Eater About Pore Swed fen 2 ae Gwines Dm hastada Caa rehe ee 2 bag Peet Leret jooni bladel sy J Peery kagus e Fin I ansar Power On v E rR 17 Eatin tomate Beset seen n Mache Abst fe J ened mode Dra mema Fade Fro 2 r C Thema Tund Pn Pitt Test tabel No Media Timeout The no media timeout value represents the number of inches of media fed through the printer without detecting an index mark prior to reporting an error EXAMPLE IF NO MEDIA TIMEOUT IS SET TO 12 THE PRINTER WILL CONTINUE TO FEED 12 INCHES OF MEDIA WITHOUT DETECTING AN INDEX MARK BEFORE REPORTING AN ERROR Debug Report Level Specifies the method by which the printer reports error Values None Turns error reporting Off Serial Printer sends error report to host device via serial port Serial 8 Label Printer sends error report via serial port and prints an error label Auxiliary Power ON Check Auxiliary Power ON to enable the 5V serial port output Enable Automatic Reprint Checking the Enable Automatic Reprint box prompts the printer to reprint a label in the event the printer detects an index mark prior to completing the reque
12. eTPG Printer Administrator installation instructions on http www ADMINISTRATOR CognitiveTPG com resources_Utility aspx for the EZ LP printer You can also follow WILL ALSO LOAD this path http www CognitiveTPG com gt Downloads gt Utility This process will also PRINT DRIVERS install the Windows drivers for the printer on your computer Note that USB Serial or FOR COGNITIVETPG LABEL PRINTERS COGNITIVETPG PRINTER ADMINISTRATOR UTILITY IS VERY USEFUL FOR CONFIGURING TROUBLESHOOTING AND UPDATING THE EZ LP PRINTER DOWNLOADS Ethernet connection is required for configuration via this utility Utility tor A799 NOTE FOR BEST m RESULTS POWER PRODUCTS OFF PRINTER PRIOR TO INSTALLING A COGNITIVETPG PRINTER ADMINISTRATOR AND PRINTER DRIVERS Utility tor EZ LP 12 hit Java haned printer administr ation tility After downloading and installing CognitiveTPG Printer Administrator and driver files proceed with driver installation to connect the print to Administrator via USB connection 14 Windows Driver Installation Installing Printer via USB 1 Connect the printer via the USB cable to the host system and the Found New Hardware Wizard will appear Select No not at this time and click Next Found New Hardware Wizard Welcome to the Found New Hardware Wizard Windows wil sesch ix cumert and undated software by looking on yout computer on the hardvese installation CO or on the Wi
13. following port and choose the appropriate Serial Parallel or USB port then click Next Select a Printer Port 12 Select the printer model you are replacing from the available list of printers and click Next Install Priester Soltware The mar tachser and mode detemine weich carter eativase to use 13 Select Keep existing driver recommended and click Next Use Existing Driver N Adi vahid th cite You can une c rapiace the emiiri A 12 14 Provide a Printer name and select ifthe EZ LP will be the default printer then click Next Mame Yous Printer Vou mail sisig a mame to thes pariisi 15 Select Do not share this printer then click Next 16 Select No when asked Do you want to print a test page then click Next Pret Test Page To conten that the panter is nitaled properly you can punt a test page 4 IMPORTANT IF BAUD RATE BETWEEN HOST SYSTEM AND EZ LP ARE NOT EQUAL THE PRINTER WILL NOT PRINT EZ LP DEFAULT BAUD RATE IS 9600 17 Select Finish to complete the installation of the EZ LP printer Chapter 4 Installing CognitiveTPG Printer Administrator and Print Drivers CognitiveTPG Printer Administrator is a Java based utility designed for installation on various operating system platforms Administrator allows complete control over the NOTE INSTALLING profiles and settings of the EZ LP printer COGNITIVETPG PRINTER Follow the Cognitiv
14. his file should be saved on the root CA directory The example below shows the code to shift the printed image left by 0 50 inches The 50 represents the amount of shift desired in hundredths of an inch and can be changed to another amount VARIABLE WRITE END For additional setting adjustment codes please contact technical support or reference the CPL Programmer s Guide at www CognitiveTPG com Click START gt Run then type cmd and click OK Run U E Type the name of a program folder document or Internet resource and Windows wil open it for you on E o Caj aa mie 7 Type in one of the COPY commands below depending on the communication interfaced used The examples show filename txt which represents the file name of the txt file created in step 2 26 NOTE CHANGING VARIABLE PRINTER SETTINGS WITH THE USB FLASH DRIVE REOUIRES USE OF THE COGNITIVE PROGRAMMING LANGUAGE EZ LP WILL NOT PRINT CPL LABEL FORMATS BUT WILL RECOGNIZE CPL BASED PRINTER SETTING COMMANDS FOR MORE INFO ON PROGRAMMING WITH CPL PLEASE REFERENCE THE CPL PROGRAMMERS GUIDE IMPORTANT WHEN USING USB FLASH DRIVE PRINTER WILL ONLY UPGRADETO A NEWER FIRMWARE REVISION CAUTION REMOVING USB FLASH DRIVE WHILE FIRMWARE IS LOADING COULD DAMAGE THE PRINTER For Parallel connection the interface is typically LPT1 8 CN WINDOWS oystem Zumdmen Hit
15. ndows Updiste Wieb sie mith pors pin do zes dis Can Windows connect to Windows Update to seach koe volteme C Yes thet tone oriy C Yes now and peony time connect a dena Ho net tis jmd Click Next to continue 2 Select Install from a list or specific location Advanced and click Next Found New Hardware Wizard This witaed heba you install software tor Cognitive 080 42 Zoe Zinn 1 your hardware came with an installation CD ED or Nope disk insert it now What do pou wart the wind to do C inal the schwere sdomaicaly Recommended instal hom a tet ot joech bosan Advanced Click Nest to continue te ie um 3 Select Include this location in the search and then click the Browse button Select the location C Program Files Cognitive Drivers and click Next E Please choose pour search and imlallabon options Use te check bows below to lt or rar the delak search mich chides boat baths and mn meda The best doves ound we brutale T Sch esncwabhe madia floppy CD ROM AT E Frog Fils Lognerme Over Dome C Dart search will choose the ven bo ential Chase the option to such the Gerace hines from a bal Wires dom nol uam that te dier you choose ndl be the Bert mutch lot your hardware San Fe 15 4 The applicable CognitiveTPG driver for your printer will be installed Please wait while the wizasd installs the soltwase EI 5 Click Finish to
16. plied C Feed Button Press to advance media Press and hold while turning unit on to initiate self test and print configuration label D On Off Switch Turns printer power On Off E Power Connector Input for auto ranging power supply F USB B Port USB Device bidirectional communications port G USB A Port USB Host port for peripheral input or USB flash drive H Serial Port Serial DB9 bidirectional communications port Parallel Port Parallel Centronics unidirectional communications port J Ethernet Port 10 100 Ethernet port Component Function A Printhead Printing mechanism B Platen Roller Friction feed printing surface C Printhead Latches Latches for printhead mechanism D Media Guide Holds and guides label roll Chapter 2 Printer Installation Setting up the EZ LP Printer Connecting the Interface and Power Cables IMPORTANT PRIOR TO CONNECTING ANY INTERFACE CABLE AND POWER CABLE TO PRINTER MAKE SURE PRINTER IS OFF NOTE EZ LP IS CONFIGURED TO USE STANDARD STRAIGHT THROUGH SERIAL CABLE WHEN USING THE COM SER PORT TO CONNECT TO A DTE DEVICE SUCHASA COMPUTER POWER OFF 1 Make sure power switch is OFF 3 Connect the AC adapter to the power connector on the printer 2 Connect power cable to AC ada
17. pter r A 0 4 Plug the power cable into an AC outlet 5 Connect the interface cable to the rear of the printer For Serial or Parallel cables securely fasten the interface connector screws or clips e us Power OFF COM SER Power OFF iy Parallel Centronics Install on Parallel Cable as Shown CAUTION DO NOT TOUCH PRINTHEAD ELECTROSTATIC DISCHARGE ESD FROM THE HUMAN BODY OR OTHER OBJECTS CAN DAMAGE PRINTHEAD PLEASE USE STATIC SAFE PROCEDURES WHEN WORKING WITH PRINTHEAD PRINTHEAD MAY BE HOT AFTER PRINTING CAUTION A AS W Loading Media NOTE USE ONLY COGNITIVETPG APPROVED MEDIA FOR MORE INFORMATION ON COGNITIVETPG APPROVED SUPPLIES CONTACT US AT 800 732 8950 OR AT COGNITIVETPG COM Unpack and prepare outward 2 Raise dust cover wound or inward wound media for installation into printer 3 Place media roll in open dust 4 Unlatch and raise printhead cover mechanism SE M It 5 Guide media through opening 6 Adjust right side media holder to under printhead mechanism Keep match width of media media face up L 7 Place media roll on media holders 8 M
18. r box Description 14 00 0001 4 5 x 6 25 Cleaning card 14 00 0002 none 12 Cleaning pen 28 Use the chart below for troubleshooting your EZ LP printer prior to contacting Technical Support If you are unable to resolve the problem using the chart below please contact our Technical Support Symptom Possible Cause Recommended Solution Red Ready Light Print Head Unlatched Securely latch printhead Out of Media Ribbon Replace media ribbon Printer Paused Press Feed Button to continue printing Red Power Light Incorrect Power Supply Verify use of correct power supply Printing Too Light Printer Darkness Setting Increase printer Darkness using CognitiveTPG Printer Administrator Driver Darkness Setting Increase the Darkness value within the printer driver Printhead Dirty Clean printhead Printing Blank Labels Incorrect Media Use direct thermal media in printer Continuously Feeding Labels Printer out of Calibration Calibrate printer using CognitiveTPG Printer Administrator Feed Button Not Working Printer is running a stored program With print head unlatched turn printer off and back on then re latch printhead Print Not Positioned Properly Top of Form or Print Width reguires adjustment Adjust Top of Form and Print Width using CognitiveTPG Printer Administrator Media Drifting During Printing Media Guide imprope
19. rly adjusted Verify Media Guide is positioned properly Skipping Labels During Printing Label Design Decrease height of label Printer out of Calibration Recalibrate printer using CognitiveTPG Printer Administrator 29 The EZ LP ships with the following default settings Parameter Default Setting Programming Language Auto automatically detects and sets to EcPL or ZcPL Speed 5 ips 127 mm s Label Width 432 4 32 inches or 110 mm Label Length Measure label automatically measures and sets label length at power up Indexing Type Gap Reference Point 0 0 upper left corner Auto Top of Form On Enable Label Present On Advance Label 25 0 25 or 6 4 mm Retract Label 25 0 25 or 6 4 mm Delay Time Retract Label 0 seconds Serial Port Settings serial port printers only 9600 bps 8 bit data 1 stop bit no parity DCE configuration use straight through cable Settings below only apply to printers with Ethernet Printer IP Address 10 0 0 12 Net Mask 0 0 0 0 Gateway 0 0 0 0 DHCP On LPD On RTEL On RTEL Port Number 9100 30
20. s 29 Congratulations on the purchase of a CognitiveTPG EZ LP desktop label printer With its durable design the EZ LP provides professional guality direct thermal label printing and performance CognitiveTPG is committed to providing a reliable product and user experience This User s Manual provides information on how to install the printer and includes all necessary user support information The EZ LP box will contain the following parts e 1 EZ LP Printer e 1 Quick Start Guide 1 Auto Ranging Power Supply 1 Power Cord Optional snap on Ferrite bead only with Parallel configuration printers Guide Ra EZD42 21X5 ZXP Models Only Ouick a Ferrite bead to be installed on Parallel cable if used al Parallel cable not included e 41 F to 104 F 5 C to 40 C 20 to 85 non condensing R H relative humidity 4 0 F to 122 F 20 C to 50 C 5 to 95 non condensing R H relative humidity Rear View Ethernet USB Model Rear View Serial Parallel USB Model Component Function A Power Indicator Indicates power status ON printer on and ready to print OFF no power applied B Ready Indicator Indicates printer status GREEN printer ready to accept data RED printer error empty media roll or paused operation during batch mode processing OFF no power ap
21. sing the Profile Management section of CognitiveTPG Printer Administrator Profile Management displays a list ofthe printer s current variable settings or JE Correction Setro Printer Settings Label Prutioring Posta ard otpis Prati Management Frvmere Unga Saree Ester e VAALAILE COMM WO 0 1 ROBUST 4 VARMARE TYTEPR 4006 3077 VARALE PERNT 12 00 10 VARIARE ETHERNET NET VASK 255 5 255 555 VARIARE TOERMT GATEWEY 3 4 0 0 VAARANDI CDERNET UO ON VARIARE EIHERNET DHCP ON VARLAD E PECIEONTLAOCL OFF 10 0 VARCARE PL CALIDGATE OFF VARIARE WID 47 VARIARE NODC 1 MAAAR F OFF M m VAGIARLE ALD POWER A VARIARE EIA A LEVE ZUR At hice VARIARE RIPORTI LEVI NA AC VARIARE UR OR VARE WETE Pe Obtaining Printers Current Profile 1 Select the Profile Management tab in CognitiveTPG Printer Administrator 2 Click the Get Printer s Current Profile button Saving the Current Printer s Profile 1 Select the Profile Management tab in CognitiveTPG Printer Administrator 2 Click the Get Printer s Current Profile button 3 Click the Save Profile to File button Applying a Saved Profile to the Printer PAN Select the Profile Management tab in CognitiveTPG Printer Administrator Click the Open Stored Profile button Select the desired Stored Profile and click Ok Click the Apply Profile to Printer button 23 CAUTION TURNING THE PRINTER OFF DURING FIRMWARE INSTALLATION C
22. sted label Media Adjust Adjust the sharpness of the leading edge of printed text or rotated barcodes Media Adjust range 0 to 3 Pitch The pitch represents the dots per inch dpi setting for the printer Values 100 or 200 for 200 dpi printers Darkness The Darkness value adjusts the print darkness Darkness range 200 to 800 NOTE THE FACTORY DEFAULT FOR DARKNESS IS 0 Primary Language Selects the primary command language the printer uses The EZ LP is defaulted to AUTO for automatic detection and selection of EcPL or ZcPL You may also manually select EcPL or ZcPL command languages NOTE THE EZ LP DOES NOT SUPPORT TPCL COMMAND LANGUAGE OR CPL COMMAND LANGUAGE PRINTING Thermal Mode Thermal Transfer mode is not available on the EZ LP printer Print Width The Print Width value adjusts the maximum printing width of the printer Maximum print width is 4 1 104 mm media width range is 2 0 to 4 25 50 to 108 mm for EZ LP 20 NOTE WHEN TIME IS SETTO OTHE LABEL WILL REMAIN ADVANCED UNTIL THE NEXTLABEL IS PRINTED TTT lii i TT juhmi ie Gare Settings Printer settings tabel Paatsa m nt and Otis rule tacayemert esmane tsyo sage teu Aout Pere wit inches 25 eo t Lat evet the aga ehted arena the stalon the porte porto rem Le tothe 17 tordi Label Present nji bon te contol sis Auto Recalibration Check and Apply Enable Auto Recalibr
Download Pdf Manuals
Related Search