LG Flatron 563LE (White) 15" LCD Monitor
Contents
1. and V position icon in the on screen display On the screen background vertical bars or stripes are visible m Push the AUTO SET Button m f the results are unsatisfactory decrease the vertical bars or stripes using the CLOCK icon in the on screen display Any horizontal noise appearing in any image or characters are not clearly portraid m Push the AUTO SET Button a If the results are unsatisfactory decrease the honzontal bars using the PHASE icon in the on screen display NO SIGNAL message m The signal cable is not connected or is loose Check and secure the connection OUT OF RANGE message appears Picture is blank m The frequency of the signal from the video card is outside the operating range of the monitor Horizontal Frequency 31kHz 61kHz Vertical Frequency 56Hz 75Hz Use the graphics board s utility software to change the frequency setting Refer to the manual for graphics board You can change the setup to the supported resolution using the Safe Mode Press the F8 key dunng booting the system The power LED is illuminated amber a The monitor is in its display power management mode m There is no active signal coming from the PC a The signal cable is not fastened securely m Check the computer power and graphics adapter configuration The monitor doesn t enter the power saving off mode Amber Computer video signal is not VESA DPMS standard Either the PC or the video controller card is not2. Introduction The 563LE Flat Panel Monitor has an active matrix TFT Thin Film Transistor LCD Liquid Crystal Display This monitor is designed for use in small working areas or for those who need more working space on the desk L cb _ O Z T Features The 563LE is a 15 0 inch 15 0 inches viewable intelligent micropro cessor based monitor Digitally controlled auto scanning is done with the microprocessor for honzontal scan frequencies between 31 and 61kHz and vertical scan frequencies between 56 and 75Hz The microprocessor based digital controls allow you to adjust conveniently a variety of image controls by using the OSD On Screen Display The monitor is shipped with 14 factory pre programmed video modes that are permanently resident In addition there are 16 user storable modes for a total of 30 memory modes Plug and play capability if supported by your system This monitor has DDC 2B function Compliant with the following regulated specifications EPA ENERGY STAR Swedish TCO 99 For detailed information please refer to the Reference Guide provided Connecting the Monitor On the back of the monitor are two plug in connections one for the AC power cord and the other for the signal cable from the video card Power off both the monitor and PC Connect the 15 pin VGA connector of the supplied signal cable to the output 4 VGA video connector on the PC and the m
3. OSD by Pressing the OSD Button On Screen Display OSD Selection and Adjustment You were introduced to the procedure of selection and adjusting an item using the OSD system Listed below are the icons icon names and icon descriptions of the items that are shown on the Menu OSD Adjust Description BRIGHTNESS CONTRAST gt Brightness pa j Used to adjust the brightness of the Q 88 screen CR gt 100 z Contrast Adjust the display to the contrast desired COLOR PRESET 9300K 6500K l PRESET ere A To appear the displays color temperature iai lt UL gt e 9300K Slightly bluish white el gt BLUE IIIiiIIII a e 6500K Slightly reddish white RED To set your own color levels GREEN To set your own color levels BLUE To set your own color levels POSITION Cr Vertical Position E i To move image up and down fej B 39 W Horizontal Position To move picture image left and right On Screen Display OSD Selection and Adjustment OSD Adjust Description TRACKING CLOCK To minimize any vertical bars or stripes visible on the screen CLOCK ININIM background The horizontal screen PHASE Illi size will also change PHASE To adjust the focus of the display This item allows you to remove any horizontal noise and clear or sharpen the image of characters SETUP LANGUAGE To choose the language in which the control names are displayed LANGUAGE gt ENGLISH OSD POSITION gt mm ELAPSED
4. TIME 0H QOSDPOSITION To adjust position of the OSD window 1024x768 60Hz on the screen PRESET MODE ELAPSED TIME To display the use time of monitor Video Memory Modes The monitor has 30 memory locations for display modes 14 of which are factory preset to popular video modes Display Modes Resolution CONOOARWDND 10 11 12 13 14 User Modes VGA VGA VGA MAC VESA VESA VESA VESA VESA VESA MAC VESA VESA VESA Display Modes Resolution 640 x 350 720 x 400 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 Horizontal Freq kHz 31 47 31 47 31 47 35 00 37 86 37 50 35 16 37 88 48 08 46 88 49 72 48 36 56 48 60 02 Vertical Freq Hz 70 70 60 67 73 15 56 60 72 15 15 60 70 15 Modes 15 30 are empty and can accept new video data If the monitor detects a new video mode that has not been present before or is not one of the preset modes it stores the new mode automatically in one of the empty modes starting with mode 15 If you use up the 16 blank modes and still have more new video modes the monitor replaces the information in the user modes starting with mode 15 Troubleshooting Check the following before calling for service Display Position is incorrect m Pushthe AUTO SET Button m f the results are unsatisfactory adjust the image position using the H position
5. atching input connector on the rear of the monitor The connectors will mate only one way If you cannot attach the cable easily tum the connector upside down and try again When mated tighten the thumbscrews to secure the connection Locate the appropriate MAC to VGA adapter block at your local computer Store This adapter changes the high density 3 row 15 pin VGA connector to the correct 15 pin 2 row connection to mate with your MAC Attach the other end of the signal cable to the side of the adapter block with 3 rows Connect the attached adapter block signal cable to the video output on your MAC Connect the plug from the AC DC adapter into the connector on the display unit Connect one end of the AC power cord into the AC DC adapter Plug the other end into a properly grounded three prong AC outlet Power on the PC then the monitor If you see the NO SIGNAL message check the signal cable and connectors After using the system power off the monitor then the PC IBM PC MACINTOSH AERE Mac Adapter D 15P Fe Signal Cable a NOTE If you see the OUT OF AC DC adapter RANGE message check to make sure your system is set to one of the factory preset modes see page A8 Location and Function of Controls Front View Power Indicator Power Button OSD sutton AUTO SET Button VESA wall mounting Rear View Conn
6. ected to another object stand type and wall mounted type optional ID Label BBBBBEEESE a BBBBBEE a BBBBEEE BBBBEBBEBEB BRBRBBESE a Kensington Security Slot l Connected to a locking D Sub Signal Connecter cable that can be purchased separately at DC Power Connecter most computer stores O9 NOTE This monitor accept a 75mm x 75mm VESA compliant mounting interface pad Control Panel Function Front Panel Controls VA lt gt Buttons Power Button OSD Button OSD v A lt gt AUTO SET D O m E Lo AUTO SET Button Power DPMS Indicator Control Function Eca OSD Button Use this button to enter and from the on v A Se va lt gt Buttons lt gt A L_g l Ci 100 A gt 100 v Q a AUTO SET aias AUTO SET Button PROCESSING AUTO CONFIGURATION Power DPMS Indicator Power Button a screen display OSD Use these buttons to choose or adjust items in the on screen display lt Shortcut Keys gt e Brightness and Contrast can be adjusted directly without entering the On Screen Display OSD system Touch the V A 4 P buttons to adjust the settings and then the OSD button to save all changes The Brightness and Contrast functions are also available in the On Screen Display OSD menu Use this button to enter a selection in the on screen display AUTO adjustment function Touch the AUTO SET button before using OSD menu This b
7. using the VESA DPMS power management function Display Sync Input Video Input Resolution Power Consumption Dimensions Power Input AC DC Adapter Weight Tilt Range Environmental Conditions NOTE Type 15 0inch 38 1cm Flat Panel Active matnx TFT LCD Anti Glare coating Viewable Size 15 0inch 38 1cm Pixel pitch 0 3 x 0 3mm Horizontal Freq 31 61kHz Automatic Vertical Freq 56 75Hz Automatic Input Form Separate TTL Positive Negative Signal Input 15 pin D Sub Connector Display Area 304 x 228mm 12 0 x 9 0inch Input Form Separate RGB Analog 0 714Vp p 750hm Positive Max VESA 1024 x 768 5Hz Recommend VESA 1024 x 768 60HZ Normal lt 33W Stand by Suspend lt 3W Power Off lt 3W Width 38 92 cm 15 95 inches Height 36 25 cm 14 24 inches Depth 18 24 cm 7 18 inches DC 12V 3A Input AC 100 240V 50 60Hz 1 2A 0 6A Output DC 12V 3A O O Net 4 8 kg 10 58 Ibs Down 5 Up 30 Operating Condition Temperature 10 T to 35 T Humidity 10 to 80 non Condensing Storage Condition Temperature 20 T to 60 C Humidity 5 to 95 non Condensing a Information in this document is subject to change without notice
8. utton is for the automatic adjustment of the screen position clock and phase Note Some signal from some graphics boards may not function properly If the results are unsatisfactory adjust your monitor s Position Clock and Phase manually This indicator lights up green when the monitor operates normally If the monitor is in DPM Energy Saving mode stand by suspend power off this indicator color changes to amber Use this button to turn the monitor on or off On Screen Display OSD Control Adjustment Making adjustments to the image size position and operating parameters of the monitor are quick and easy with the On Screen Display Control system A quick example is given below to familiarize you with the use of the controls Following section is an outline of the available adjustments and selections you can make using the OSD NOTE Allow the monitor to stabilize for at least 30 minutes before making image adjustment To make adjustments in the On Screen Display follow these steps OSD v A AUTO SET D en A EZ Ly OSD AUTO SET v A lt lt gt A lt A Oo ee eee eee L_xy 1 L_g 1 Press the OSD Button then the main menu of the OSD appears 2 To access acontrol use the wa Buttons When the icon you want becomes highlighted press the AUTO SET Button 83 Use the va lt gt Buttons to adjust the item to the desired level l Accept the changes by pressing the AUTO SET Button 5 Exit the
Download Pdf Manuals
Related Search