Fujitsu Siemens Celsius 422 PC Desktop
Contents
1. You will find further information in the BIOS Setup description Further information about drivers is provided in the readme files on the hard disk on the supplied drivers diskettes on the Drivers amp Utilities or on the ServerStart CD Notational conventions The meanings of the symbols and fonts used in this manual are as follows Pay particular attention to text marked with this symbol Failure to observe this warning endangers your life destroys the device or may lead to loss of data i Supplementary information remarks and tips follow this symbol gt Text which follows this symbol describes activities that must be performed in the order shown u This symbol indicates that you must enter a blank space press the Space Bar at this point d This symbol indicates that you must press the Enter key Text in this typeface indicates screen outputs Text in this bold typefaceindicates the entries you make via the keyboard Text in italics indicates commands or menu items Quotation marks indicate names of chapters or terms Important notes Store this manual close to the device If you pass the device on to third parties you should pass this manual on with it Be sure to read this page carefully and note the information before you open the device You cannot access the system board components without first opening the device How to dismantle and reassemble the device is described in the Operating Manual ac2. SYSTEMBAUGRUPPE D1236 SYSTEM BOARD D1236 TECHNISCHES HANDBUCH TECHNICAL MANUAL co FUJITSU COMPUTERS SIEMENS Sie haben technische Fragen oder Probleme Wenden Sie sich bitte an unsere Hotline Mo Fr 9 18 Uhr Sa 9 14 Uhr Tel 4449 0 180 3777 000 _ Ihren zust ndigen Vertriebspartner e Verkaufsstelle Weitere Informationen finden Sie im Handbuch Sicherheit Garantie und Ergonomie Aktuelle Informationen zu unseren Produkten Tipps Updates usw finden Sie im Internet http www fujitsu siemens com Are there any technical problems or other questions you need clarified Please contact e your sales partner e your sales outlet You will find further information in the manual Safety Warranty and Ergonomics The latest information on our products tips updates etc can be found on the Internet under http www fujitsu siemens com Dieses Handbuch wurde auf Recycling Papier gedruckt This manual has been printed on recycled paper Ce manuel est imprim sur du papier recycle Este manual ha sido impreso sobre papel reciclado Questo manuale amp stato stampato su carta da riciclaggio Denna handbok r tryckt pa recyclingpapper Dit handboek werd op recycling papier gedrukt Herausgegeben von Published by Fujitsu Siemens Computers GmbH Bestell Nr Order No A26364D1236 Z20 17419 Printed in the Federal Republic of Germany 0101 0101 26361 01236 21
3. 20 1 7419 Systembaugruppe D1236 System Board D1236 Technisches Handbuch Technical Manual Ausgabe Januar 2001 January 2001 edition Intel Pentium und Celeron sind eingetragene der Intel Corporation USA Microsoft MS MS DOS und Windows sind eingetragene Warenzeichen der Microsoft Corporation PS 2 und OS 2 Warp sind eingetragene Warenzeichen von International Business Machines Inc Alle weiteren genannten Warenzeichen sind Warenzeichen oder eingetragene Warenzeichen der jeweiligen Inhaber und werden als gesch tzt anerkannt Alle Rechte vorbehalten insbesondere auch auszugsweise die der bersetzung des Nachdrucks der Wiedergabe durch Kopieren oder hnliche Verfahren Zuwiderhandlungen verpflichten zu Schadenersatz Alle Rechte vorbehalten insbesondere f r den Fall der Patenterteilung oder GM Eintragung Lieferm glichkeiten und technische nderungen vorbehalten Dieses Handbuch wurde erstellt von cognitas Gesellschaft f r Technik Dokumentation mbH www cognitas de Copyright Fujitsu Siemens Computers GmbH 2001 Intel Pentium and Celeron are registered trademarks of Intel Corporation USA Microsoft MS MS DOS and Windows are registered trademarks of Microsoft Corporation PS 2 and OS 2 Warp are registered trademarks of International Business Machines Inc All other trademarks referenced are trademarks or registered trademarks of their respective owners whose protected rights are acknowledged All right
4. 45 connector is equipped with a yellow and a green LED light emitting diode 1 Yellow indicator 2 Green indicator Green a connection exists e g to a hub Yellow Link Mode the LAN connection is active WOL mode a Magic Packet is being received 8 English 26361 01236 2120 2 7419 Settings with switches and jumpers Settings with switches and jumpers 0000000000 0000000000 DIMM 3 DIMM 2 DIMM 1 c Switch 1 must be set to off Switch 3 Write protection for floppy disk Switch 2 System BIOS recovery Switch 4 must be set to off il The clock frequency of the processor is set automatically Recovering System BIOS switch 2 Switch 2 enables recovery of the old system BIOS after an attempt to update has failed To restore the old system BIOS you need a Flash BIOS Diskette please call our customer service centre On The System BIOS executes from floppy drive A and the inserted Flash BIOS Diskette restores the System BIOS on the system board of Normal operation default setting Write protection for floppy disks switch 3 Switch 3 is used to define whether floppy disks can be written or deleted in the floppy disk drive To write and delete floppy disks the write protection in BIOS Setup must be disab
5. 59 LAN controller 10 100 Mbit s with RJ45 interface WOL with Magic Packet is supported as is booting from LAN with Bootix LAN BootP or Intel PXE Analogue Devices AD1885 AC 97 Audio Codec internal Stereo CD In Stereo AUX In external Mono Micro In Stereo Line In Stereo Line Out Game Midi port 3 DIMM slots for up to 3 GB main memory DDR DRAM memory modules meet the PC200 PC266 specification with ECC Flash BIOS Fujitsu Siemens system monitoring and temperature monitoring Energy saving functions and ACPI requires an operating system that supports ACPI Switching on off standby mode suspend mode via on off switch Switching on off via software Wake RTC Wake on LAN Wake on PCI Cards Wake on USB Security functions Chipcard reader interface SmartCard reader Processor serial number Cover monitoring cover monitoring reports when the cover has been opened without authorisation System Setup and Keyboard password parallel and serial ports can be deactivated Floppy disk write protection hard disk virus warning function A Flash BIOS and EEPROMs on the memory modules virus protection function 26361 01236 2120 2 7419 English 3 Features e 5POCIslots PCI slots support 3 3 V main and auxiliary voltages e 1 AGP slot The AGP slot supports 1x 2x and 4x AGP mode The voltage is detected and configured automatically DE h
6. ard disk controller connected to PCI bus for up to four IDE drives e g IDE hard disk drives ATAPI CD ROM drives The IDE hard disk controller are ATA33 66 100 ultra DMA capable and support PIO modes 0 4 Floppy disk drive controller possible formats 720 KB 1 44 MB 2 88 MB The system board supports booting from a 120 MB IDE floppy disk drive 1 external parallel port ECP and EPP compatible 1 external serial port 160550 compatible with FIFO 1 external serial port 160550 compatible with FIFO 1 internal chipcard reader interface SmartCard reader This port does not support Wake On Ring This interface can also be used as a second serial port 166550 compatible with FIFO e 1 internal WOL interface e 2external PS 2 ports for keyboard and mouse e 2external USB ports USB ports D E F internal Realtime clock calendar with integrated battery backup 4 English 26361 01236 2120 2 7419 Features Interfaces and connectors 0000000000 DIMM 3 DIMM 2 NE DIMM 1 re Po seu de 12 PS 2mouse port 72 Serial port 2 2 PS 2keyboard port 8 Game Midi port 3 2 LAN connector 9a Aud
7. companying the device Please note the information provided in the Safety chapter in the device s Operating manual Incorrect replacement of the lithium battery may lead to a risk of explosion It is therefore essential to observe the instructions in the Add on modules Replacing the lithium battery section 26361 01236 2120 2 7419 English 1 Important notes The shipped version of this board complies with the requirements of the EEC directive 89 336 EEC Electromagnetic compatibility Compliance was tested in a typical PC configuration When installing the board refer to the specific installation information in the Operating Manual or Technical Manual of the receiving device Connecting cables for peripherals must be adequately shielded to avoid interference Components can become very hot during operation Ensure you do not touch components when making extensions to the system board There is a danger of burns replacement of system expansions Information on which system expansions you can i The warranty is invalidated if the device is damaged during the installation or use is available from your sales outlet or the customer service centre Information about boards To prevent damage to the system board or the components and conductors on it please take great care when you insert or remove boards Take great care to ensure that extension boards are slotted in straight without damaging components or conductor
8. essed by the BIOS or the application Cover monitoring Unauthorised opening of the cover is detected even when the system is switched off However this will not be indicated until the system is operating again 26361 01236 2120 2 7419 English 7 Features Voltage monitoring The voltages 12 V 5 V and the CMOS battery are monitored With hardware monitoring regardless of the operating system and processor the advantages compared to conventional software monitoring are clear suitable for all operating systems and processor types no additional load on processor performance optimum temperature protection even if process faults or faults are present in the operating system optimum noise reduction Three different operating modes are available and can be configured in BIOS Setup System Management Hard disk connection An ultra ATA 66 or ultra ATA 100 hard disk must be connected with a cable especially designed for the ultra ATA 66or ultra ATA 100 mode gt Connect the end of the cable marked with blue to the system board LAN connector This system board has an optional Intel 82550 EY or 82559 LAN controller which supports transfer speeds of 10 Mbit s and 100 Mbit s The LAN controller is equipped with a 3 Kbyte transmission and receiving buffer FIFO and supports WOL function through Magic Packet Remote boot via LAN is supported with Bootix LAN BootP and Intel PXE are supported The LAN RJ
9. ing on the socket A with regard to the position 4 The angled corner of the processor may be covered by the heat sink In this case let yourself be guided by the marking in the rows of pins on the underside of the processor gt Push the lever back down until it clicks into place 5 26361 01236 2120 2 7419 English 11 Add on modules Upgrading main memory These slots are suitable for DIMM format 64 128 256 512 MB and 1 GB DDR DRAM memory modules Memory modules with different memory capacities can be combined You may only use unbuffered 2 5V memory modules Buffered memory modules are not supported DDR DRAM memory modules must meet the PC200 PC266 specification Installing a memory module gt Push the holders on each side of the memory compartment outwards gt Insert the memory module into the location 1 ensuring that it is in the correct orientation gt Atthe same time flip the lateral holders upwards until the memory module snaps in place 2 Removing a memory module gt Push the clips on the right and left of the compartment outward 1 gt Carefully remove the memory module from the compartment 2 12 English 26361 01236 2120 2 7419 Add on modules Installing network board with WOL gt Install the network board as described in the operating manual for your unit gt Push the WOL cable onto the WOL plug connector of the system board i To use the WOL functionality of a netwo
10. io Line Out 4 USB ports 1 2 9b Audio Line In 5 Serial port 1 9c Audio Micro In 6 Parallel port The components and connectors marked are not necessarily present on the system board 26361 01236 2120 2 7419 English 5 Features 3555555535 16 9000000000 DIMM 3 DIMM 2 DIMM 1 eel xi 1 Chipcard reader interface or serial port 2 9 USBportF 2 Power supply monitoring 10 USB port E 3 Cover monitoring 11 USB port D 4 Floppy disk drive 12 Fan 2 e g for the processor 5 IDE drives 3 and 4 secondary 13 CD audio input 6 IDE drives 1 and 2 primary 14 AUX audio input 7 Connector for control panel and 15 Fan 1 e g for the processor loudspeaker 16 Power supply 8 Wake On LAN The components and connectors marked are not necessarily present on the system board 6 English 26361 01236 2120 2 7419 Features Temperature System monitoring Temperature and system monitoring aim to reliably protect the computer hardware against damage caused by overheating In addition any unnecessary noise is also prevented by reducing the fan speed and information is provided about the system status Cover monitoring protects the system from unauthorised opening An onboard controller developed by Fujitsu Siemens C
11. led in menu Security the field Diskette Write must be set to Enabled On The floppy disk drive is write protected of Floppy disks can be read written and deleted default setting 26361 01236 2120 2 7419 English 9 Add on modules Add on modules Exit Suspend mode switch off the device and remove the power plug from the mains supply before carrying out any of the procedures described in this chapter Even when you have switched off the device parts e g memory modules AGP and PCI extension boards are still supplied with power All AGP and PCI slots support 3 3 V main and auxiliary voltages 0000000000 0000000000 DIMM 3 DIMM 2 DMM 1 Socket for processor with heat sink 5 Lithium battery 2 Location bank 1 for main memory 6 PClslots 1 2 3 4 5 3 Location bank 2 for main memory 7 AGP slot 4 Location bank 3 for main memory 10 English 26361 01236 2120 2 7419 Add on modules Installing and removing processors gt Pull the lever in the direction of the arrow 1 and lift it as far as it will go 2 gt Remove the old processor from the socket 3 gt Insert the new processor in the socket so that the angled corner of the processor matches the cod
12. nd Memory Controller Universal Serial Bus Hub GPA Graphics Performance Video Graphic Adapter Accelerator LLL 26361 01236 2120 2 7419 English 15
13. omputers controls the temperature and system monitoring The following functions are supported Temperature monitoring Measurement of the processor temperature measurement of the system temperature with an onboard temperature sensor measurement of the device temperature with an optional temperature sensor AUX Temperature control The temperature is controlled by adjusting the fan speed and or by reducing the clock frequency of the processor The clock frequency of the processor is dependent upon the setting in the BIOS Setup Temperature dependent processor speed control enables a reduced fan speed decreasing noise Fan monitoring Fans which have been removed blocked or sticky fans are detected and blocked or sticky fans are operated with 12 V pulse voltage Ifthe device has a monitored fan removed while the system is switched off this is indicated by the message LED when the system is switched on again and processed by the BIOS or the application Fan control With the exception of the auxiliary fan AUX the fans are regulated according to temperature Sensor monitoring The removal of or a fault in a temperature sensor is detected Should this happen all fans monitored by this sensor run at maximum speed to achieve the greatest possible protection of the hardware If the device has a monitored fan removed while the system is switched off this is indicated by the message LED when the system is switched on again and proc
14. re ved feilaktig skifte av batteri Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten Brukte batterier kasseres i henhold til fabrikantens instruksjoner The following graphic representation is also valid if the lithium battery is built in vertically gt Liftthe contact 1 a few millimetres and remove the battery from its socket 2 gt Inserta new lithium battery of the same type into the socket 3 14 English 26361 01236 2120 2 7419 Glossary Glossary The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations Not all technical terms and abbreviations listed here are valid for the described system board IPSEC Internet Protocol Security Power Management Interface ATA Advanced Technology NIC Networking Interface Card Attachment BIOS Basic Input Output System P64H PCI64 Hub CAN Controller Area Network PCI Peripheral Component Interconnect Central Processing Unit Preboot eXecution Environment Communication Network Riser Random Access Memory Memory Module Analogue Converter LN LINE Access Memory DIMM Dual Inline Memory Module RIMM Rambus Inline Memory Module DRAM Dynamic Random Access RTC Real Time Clock Memory Error Correcting Code Soundblaster Programmable Read Only Access Memory Memory First In First Out Streaming Mode Instruction puce US Single Instruction Multiple Data GMCH Graphics a
15. rk board the power supply must provide a 5 V auxiliary voltage of at least 1 A If the system board was not already incorporated in a device when you bought it you must check whether your power supply can provide the auxiliary voltage You may find further information in the supplied description of the network board 26361 01236 2120 2 7419 English 13 Add on modules Replacing the lithium battery Incorrect replacement of the lithium battery may lead to a risk of explosion The lithium battery must be replaced with an identical battery or a battery type recommended by the manufacturer CR2032 Do not throw lithium batteries into the household waste They must be disposed of in accordance with local regulations concerning special waste Ensure that you insert the battery the right way round The plus pole must be on the top e VAROITUS Paristo voi r j ht jos se on virheellisesti asennettu Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin H vit k ytetty paristo valmistajan ohjeiden mukaisesti e VARNING Explosionsfara vid felaktigt batteribyte Anv nd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren Kassera anv nt batteri enligt fabrikantens instruktion e ADVARSEL Lithiumbatteri Explosionsfare ved fejlagtig h ndtering Udskiftning m kun ske med batteri af samme fabrikat og type Lever det brugte batteri tilbage til leverand ren e ADVARSEL Explosionsfa
16. s including rights of translation reproduction by printing copying or similar methods even of parts are reserved Offenders will be liable for damages All rights including rights created by patent grant or registration of a utility model or design are reserved Delivery subject to availability Right of technical modification reserved This manual was produced by cognitas Gesellschaft f r Technik Dokumentation mbH www cognitas de Contents niger Notational conventions IMPONA NOOS nes Information about boards Interfaces and connectors Temperature System monitoring Hard disk connection oe LAN ee sanken Settings with switches and jumpers cceeeeeseeeceeeeeteeeeseeeeaeecaeceseeseaeesseeseaeesaeseaeersaeeeeeeeaserseess Recovering System BIOS switch 2 Write protection for floppy disks switch 3 Add on modules Installing and removing processors Upgrading main memory Installing network board with WOL Replacing the lithium battery s ETC p 26361 01236 2120 2 7419 Introduction Depending on the configuration chosen some of the hardware components described may not be available on your system board
17. s on the system board or any other components for example EMI spring contacts Be especially careful with the locking mechanisms catches centring pins etc when you replace the system board or components on it for example memory modules or processors Never use sharp objects screwdrivers for leverage Boards with electrostatic sensitive devices ESD are identifiable by the label shown When you handle boards fitted with ESDs you must under all circumstances observe the following points You must always discharge static build up g by touching a grounded object before working The equipment and tools you use must be free of static charges e Remove the power plug from the mains supply before inserting or removing boards containing ESDs A Always hold boards with ESDs by their edges Nevertouch pins or conductors on boards fitted with ESDs 2 English 26361 01236 2120 2 7419 Features Features The components and connectors marked are not necessarily present on the system board System board in u ATX format FC PGA 370 Celeron processor with 66 MHz Front Side Bus for PGA 370 socket and Pentium III with 100 133 MHz Front Side Bus for PGA 370 socket Celeron and Pentium Ill processors support MMX technology and Intel Streaming SIMD Extensions The size and frequency of first level cache and second level cache are dependent upon the processor used VIA Apollo Pro266 Intel 82550 EY or 825
Download Pdf Manuals
Related Search