Daewoo DTQ-27S5FC 27" TV
Contents
1. Descriptions of video settings The contrast setting controls the relation between the light and black areas of the screen If the light areas are too bright and are losing details press the lt VOL button if the picture is gray and lacks contrast press the VOL button The brightness settings controls the overall amount of light in the picture If the picture is too bright press the lt VOL button if the picture is too dark press the VOLP button Sharpness controls how the TV displays edges of objects on screen If the TV shows multiple verti cal lines at the edges of an object press the lt VOL button if the vertical edges of on screen objects are fuzzy press the VOL button The color setting controls the intensity of color If the color is over saturated press the lt VOL but ton if the color is washed out press the VOL button The tint setting controls the relationship of red and green in a picture Tint is especially noticeable in flesh tones If flesh tones seem too red or purple press the VOL button if flesh tones are too green press the lt VOL button 14 Chapter 3 Operating Your TV Using Timer Functions Your TV has a built in clock and you can set the TV to turn on and off at times that you select You can also set your TV to turn off after counting down a certain amount of time Setting the Clock 1 With the TV turned on press the MENU button until Time menu will be displayed 22. cable system Follow the directions below make this connection Please note that you will normally only have to make one of the connections shown below not all of them All connections will be made to the antenna terminal on the back of your TV The antenna terminal is a silver metal post partially surrounded by two plastic tabs For help in locating the antenna termi nal see Your TV s Back Panel on page 3 Connecting an Antenna If your antenna ends in a single coaxial lead simply N press or screw the cable onto the antenna terminal on the back of your TV If your antenna ends in a pair of 300 ohm twin leads you must use a 300 ohm 75 ohm adapter available at your local electronics store Place the leads underneath the screws on the adapter tighten the screws then press the adapter onto the antenna terminal on the back of the TV Acre 2 Connecting an Antenna or Cable to Your TV Antennas with two sets of leads You might have two sets of leads from your antenna system especially if you have one antenna for VHF signals and one antenna for UHF signals If your antenna system has both a coaxial lead and twin 300 ohm leads you must obtain a combin er available at your local electronics store Press or screw the coaxial lead onto the combiner place the twin leads underneath the screws on the combiner
3. time settings return to The Wake up Time and Off Time will not function correctly unless the clock has been set 16 Chapter 4 Using Timer Functions Setting the Sleep Timer The sleep timer allows you to set an amount of time from 15 minutes to 120 minutes TV will count down the amount of time you set then turn itself off To set the sleep timer 1 With the TV turned on press the MENU button until Time menu will be displayed 2 Use the WCHA buttons to select Sleep Timer item 3 Use the lt VOLP buttons to set the sleep time Each time you press VOL you step between the available sleep times 15min 30min 45min 60min 90min or 120min 4 When the setting is correct use the WCH A buttons to select another Time function or press the MENU button to return to normal TV viewing 5 You can also set the Sleep Timer during normal TV viewing simply by pressing the SLEEP button on the remote control This button steps through the available sleep times see step 3 one by one To cancel the Sleep timer turn the TV off or set the sleep time to 0 using one of the methods described above Set Clock 12 00 AM Set Clock 12 00 AM Set Clock 12 00AM Wake Up Time 06 30AM Wake Up Time 06 30 AM Wake Up Time 06 30AM Off Time 11 30PM Off Time 11 30PM Off Time 11 30PM Sleep Timer 0 min Sleep Timer 0 min Sleep Timer 60 min Select 4 Adjust mNext Select 4 Adjust Ne
4. If you don t plan to use the receiver for several days it s a good idea to unplug it from the power outlet e Many common household cleaning agents sprays solvents and polishes will cause permanent damage to the surface of the cabinet The best cleaning agents are mild soap and a damp cloth Again thank you for choosing this Daewoo product We have employed advanced engineering techniques in its design and manufactured it in one of the world s most up to date production facilities The result is a TV receiver that we know you will be as proud to own as we were to create Very truly yours DAEWOO ELECTRONICS CORPORATION OF AMERICA qin Table of Contents Chapter 1 Overview of Your Equipment eree 2 Your TV s Front Panel ssesseeserserraesresrerererssrens 2 Your Remote Control Installing your remote control batteries ceseesecreetee see eeeteenee teens Chapter 2 Connecting an Antenna or Cable to Your TV e gt seses sss ses eee ee eee 026 Connecting an Antenna cs cescescesceeeee eee eee tee tee tne eeenenten tence eee eee een eenteanee eee nent ee tea cee eee eenea tea tee tees 6 Connecting a Cable System cesseeceeceesee eee tee teens eee eee nent eee ee eee en eee een iari kretaer eee Eee EAR i kenti F Connecting Other Pieces of Equipment marp teh E aaan e eer a re n Aa a a eraai 8 Safety Notes iieiea sia Kin neracia ieena NEn ETEA Heute cad Gea saenied BAUNA NEER EA ode shod Wed GesNea deta A
5. It incorporates a host of features designed to give you excellent performance for many years to come We realize that you re eager to turn it on and begin enjoying the high quality pictures it delivers just as quick ly as possible but we ask you to take a few minutes to read the instructions in the booklet to familiarize your self with the receiver its functions and some features which may be new to you If you follow the instruc tions this unit should give you many years of viewing pleasure If for any reason it does not we want to hear about it Please write to us at the address above Daewoo always welcomes comments and suggestions on this or any of our other products On the other hand when you discover the enjoyment reliability and ease of use that is built into it we hope that you will tell your friends and consider Daewoo when you make your next purchase of home entertain ment equipment In addition to TV receivers Daewoo produces a full line of audiovisual products built to the same high design engineering and manufacturing standards as this unit Here are a few tips that will keep your TV receiver looking great and performing for years to come e Avoid putting it in excessively hot locations Damage to the cabinet or premature component failures can result There are ventilation holes in the bottom and rear of the cabinet Make sure that they remain unobstructed Do not place the receiver on top of a thick cloth
6. Parental Control Ch Labels Select 4 Adjust Off Off Off gt To Press Next Off Off Off ABCD Next Special Closed Caption CC on Mute Power Restore Parental Control Ch Labels Select Adjust Special Closed Caption CC on Mute Power Restore Parental Control Ch Labels Select amp Adjust Special Closed Caption CC on Mute Power Restore Parental Control gt Ch Labels Select 4 Adjust Off Off Off gt To Press mNext Off Off Off gt To Press Next Special EJ Closed Caption CC on Mute Power Restore Parental Control gt Ch Labels Select 4 Adjust Special Closed Caption CC on Mute Power Restore Parental Control Ch Labels Select 4 Adjust Chapter 5 Additional Features EB NOTE Facti time you press the YCH A buttons the displayed character will change in the following order CHA ABC gt D gt gt Z gt 0 gt gt gt 9 gt t YCH 9 8 gt gt 00 gt Z gt Y gt BOA t Cearing Channel Labels 1 Select the channel which has the label you want to clear 2 3 4 Follow step 1 3 on the Ch Labels to call up the Ch Labels mode display 5 Enter in first character spaces EB Chapter 5 Additional Features Adjusting the Sound Selecting stereo SAP The MTS Multi channel TV Sound provides for an extra sound chan
7. Audio menu will be displayed Use the YCH A buttons select Treble item Press the lt VOL button to decrease the treble volume Press the VOL button to increase the treble volume Press the MENU button twice or wait few seconds to return to normal TV viewing oun WN Your setting will remain intact until you change it Your TV will then automatically reproduce either stereo or monaural sound whichever is broadcast Audio Mode Bass Treble Balance Select Adjust Audio Mode Bass Audio Mode Bass Treble Balance mExit Select 4 Adjust mExit Audio Mode Bass Treble Balance Treble Balance Select Adjust meExit Select 4 Adjust mExit Adjusting the Balance 1 With the TV turned on press the MENU button until Audio menu will be displayed Use the YCH A buttons select Balance item Press the lt VOL button to decrease the left speaker volume Press the VOL button to decrease the right speaker volume Press the MENU button twice or wait few seconds to return to normal TV viewing ou hh WD Your setting will remain intact until you change it Your TV will then automatically reproduce either stereo or monaural sound whichever is broadcast Audio Mode Bass Treble Balance Select 4 Adjust Audio Mode Bass Treble gt Balance mExit Select 4 Adjust mExit Audio Mode Bass Treble Balance Select lt 4 Adjust Au
8. The Set Clock item will be selected Press the AVOL buttons to set the clock If you hold down either lt VOL or VOL button the corresponding numbers will change more quickly 3 When the clock is set correctly use the WCH A buttons to select another Time function or press the MENU button to return to normal TV viewing Set Clock gt Set Clock 12 00AM Set Clock 12 00AM Wake Up Time Wake Up Time Wake Up Time Off Time Off Time Off Time Sleep Timer Sleep Timer ii Sleep Timer Select 4 Adjust Select 4 Adjust mNext SSelect amp Adjust Setting the Wake up time If you enter a time in the Wake Up Time setting your TV will automatically turn on at that time Follow these instructions to set the Wake Up Time After Wake up Time turned on the TV set if user do not input the user control e g remote CH or VOL key within 15 minutes the TV set will turn off automatically If user input the user control within 15 minutes the TV set will turn on continuously It is safety feature for prevent from any kind of problem without human control With the TV turned on press the MENU button until Time menu will be displayed 2 Use the WCHA buttons to select Wake Up Time item 3 If you hold down either lt VOL or VOL button the corresponding numbers will change more quickly 4 When the setting is correct use the WCH A buttons to select
9. a polarized alternating current line plug a plug having one blade wider than the other This plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit con tact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug Do not allow anything to rest on the power cord Do not locate this television equipment where the cord will be abused by persons walk ing on it Follow all warnings and instructions marked on the television equipment For added protection for this television equip ment during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the antenna or cable system This will prevent damage to the equipment due to lightning and power line surges 13 An outside antenna system should not be locat ed in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal 14 Do not overload wall outlets and extension cords as this can result in fire or electric shock 15 Never push objects of any kind into this televi sion equipment t
10. and tighten the screws Press the cable from combiner onto the antenna terminal on the back of your TV If your antenna system has two sets of twin 300 ohm leads you must obtain a combiner available at your local electronics store Place one set of twin leads underneath the screws on the combiner and tighten the screws Do the same with the other set of twin leads Press the cable from the com biner onto antenna terminal on the back of your TV Connecting a cable system N If your cable set up is not described below please contact your cable company for more information If your cable system does not require the use of a cable box simply press or screw the incoming cable onto the antenna terminal on the back your Saa TV Chapter 2 Connecting an Antenna or Cable to Your TV If your cable system requires you to use a converter box for all channels connect the incoming cable to the IN terminal on the converter box Connect another cable between the OUT terminal on the con verter box and the antenna terminal on the TV You will need to keep your TV tuned to channel 3 or 4 and change channels using the converter box Converter Box OUT IN gt If your cable system only requires you to use a converter box for some channels i e pay TV chan nels follow these steps Find the primary incoming coaxial cable Plug th
11. by the manufacturer that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Upon completion of any service or repairs to this television equipment ask the service tech nician to perform safety checks to determine that the television is in a safe operating condi tion Tf an outside antenna or cable system is con nected to the television receiver be sure the antenna or cable system is grounded so as to provided some protection against voltage surges and built up static charges Section 810 of the National Electrical Code ANSI NFPA NO 70 1984 provides information with respect to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to ground ing electrodes and requirements for the ground ing electrode EXAMPLE OF ANTENNA GROUNDING ANTENNA DISCHARGE UNIT NEC SECTION 810 20 ELECTRIC SERVICE EQUIPMENT GROUNDING CONDUCTORS NEC SECTION 810 20 GROUND CLAMPS NEC NATIONAL ELECTRICAL CODE SS POWER SERVICE GROUNDING ELECTRODE SYSTEM NEC ART 250 PART H Important Safeguards _ Daewoo Electronics Corporation of America 120 Chubb Avenue Lyndhurst NJ 07071 Dear Customer Daewoo Electronics Corporation of America would like to thank you for choosing this color television receiv er
12. distributor from whom purchased or authorized service station intact for our examination with all transportation charges prepaid to our factory To establish and receive warranty service at our factory or authorized service facilities proof of purchase dated sales invoice is required Return authorization must be obtained before any merchandise is returned to the factory This warranty does not extend to any of our electronic products which have been subjected to mis use neglect accident incorrect wiring not our own improper installation unauthorized modifica tion or to use in violation of instructions furnished by us nor units which have been repaired or altered outside of our factory nor to cases where the serial number thereof has been removed defaced or changed This warranty is in lieu of all warranties expressed or implied and no representative or person is authorized to assume for us any other liability in connection with the sake of our electronic prod ucts Over the counter exchange for units that are initially defective Initially defective is described as when the dealer opens the unit and finds that it is inoperative or a customer opens a new unit and finds that it is inoperable This unit may be returned to the factory by the dealer for exchange Under no circumstances will the customer be permitted to return the defec tive unit directly to the factory Exchange must be directly with the dealer Model Parts Lab
13. the standard for the programs which their children is going to watch 1 With the TV on press the MENU button until Special menu will appear 2 Use the WCHA buttons to select Parental Control item 3 Use the lt VOLP buttons to enter into Parental Control settings 4 Use the number buttons 0 9 to enter your password then Parental Control menu will be dis played If this is the first time you are using your Parental Control menu after entering your password you have to remember it The Parental Lock feature will be selected Use the lt VOL buttons to toggle On or Off Use the WCH A buttons to select the Parental Control settings you wish to adjust Descriptions of the Parental Control settings are on the next page Use the WCH A buttons to adjust the Parental Control settings Use the MENU button to return to the one level up menu Special EJ Closed Caption Off CC on Mute Off Repeat the Password Power Restore Off atts cai HHH Parental Control Ch Labels gt To Press Enter a new Password Select Adjust Next 0 9 Adjust K 0 9 Adjust Parental Control Parental Lock On TV Guidelines Movie Ratings No Rating Unblock Ext Source Unblock Change Password Select 4 gt Adjust Prev EB Chapter 5 Additional Features Description of Parental Control Settings 1 The TV Guidelines set the standard for TV programs excluding sports and news Use the WCHA but
14. 4 Press the MENU button to return to Set Up menu 5 Press the MENU button four times to return to normal TV viewing Your TV s channel memory will not be affected by a power outage You will not need to re program the memory unless you change the type of cable or antenna connected to your TV 3 1 Wro Language English Language English Reception Air Reception Air Memorize Channels Memorize Channels Add Delete Channels Add Delete Channels Input Tv Input TV Language English Reception Air Memorize Channels Add Delete Channels Input TV Select 4 Adjust mNext Select 4 Adjust Next Select Adjust mNext Memorize Channels Holes Air 11 Language English Memorizing all air channels Reception Air Please stand by Memorize Channels Add Delete Channels Input TV Press MENU to cancel and return to Set Up menu Select Adjust MNext Chapter 3 Operating Your VED Changing Channels You can change channels in three ways 1 The WCHaz buttons will take you through all memorized channels one by one The WCH A buttons will not access channels that have not been programmed into the TV s memory For more information about programming channels into memory see the section Programming your TV s Channel Memory on the previous page The number buttons 0 9 will take you to any channel even if it has not been memorized To change to a channel enter its number th
15. EAN be Yee 8 Chapter 3 Operating YOUR TV Sierran itn ei h Saye eee eee eee Q Turing your LV On eiaa ae o E bce ese ce A E geet dese sae ape teat geal 9 Programming Your TV s Channel Memory 1s sssceceerseeee teens cee cee ceenaateeneecee teens aescea sence testeasen tensed 9 Changing Channels seeceetsscseeesces eee tee eee ene eeeeeaten tee eee enon teat eateneee eee eea eaten eee eeeeeuten tea cee eee eens 10 Changing the Volume Aedia aiet tee eee cree ee eee een ee rene dee nee tee ne caenee eee ten tee eee eee S a ES 10 Changing The TV s Channel Memory well Adding Deleting a channel to memory Displaying the Current Channel 11 Changing the TV s Input s rsersesrereeterrnrenrrarenrerrterrereerreresresrsantnrenrerrenreasenterresrennenrenrentenreeue 12 Adjusting Video Settings aede aea nd phate ce ott e EEE M iE E E AEE OEREO 13 Returning to the factory settings re rs rrersersarrereerrasrnreareartereneanreresnrererrenusareerenusareneaneereerea 14 Descriptions of video settingS aeaea raea PARE ENKLE EREN AE TAERE NENEA EO AEE RERS 14 Chapter 4 Using Timer Functions gt sss ses ses ses sesees seo sss sss senese ese eee cee eee Setting the 0 0 Qe 15 Setting the Wake up Time ss ssssseeereeeee eee reece eee eee ceenee tee eee teen ee ee anna anes teeta ene eee eee tee teanee eee eee tes 15 Setting the Off Time Canceling the Wake up Time or Off Time Setting the Sleep Timer Cha
16. Sound 25 Using Direct button on the remote control 1 You can also change the Audio Mode setting with the remote control Press the MTS button on the remote control to select Audio Mode 2 Use this button to select the Stereo Mono or SAP Present Broadcast Your Selection Speaker Out MONO Stereo Mono MONO SAP Mono STEREO SAP Mono STEREO and SAP Stereo Stereo STEREO and SAP SAP SAP Note If a broadcast signal is weak it may cause noise and hum in stereo sound Please select the Mono mode the noise and hum should be reduced Adjusting the Bass 1 With the TV turned on press the MENU button until Audio menu will be displayed Use the WCH A buttons select Bass item Press the lt VOL button to decrease the bass volume Press the VOL button to increase the bass volume Press the MENU button twice or wait few seconds to return to normal TV viewing oa fF WwW DN Your setting will remain intact until you change it Your TV will then automatically reproduce either stereo or monaural sound whichever is broadcast Audio Mode Bass Treble Balance Select Adjust Audio Mode Bass Treble Balance Select Adjust Ea Chapter 6 Adjusting the Sound Audio Mode Bass Treble Balance Select Adjust MExit Audio Mode Bass Treble Balance Select Adjust Adjusting the Treble 1 With the TV turned on press the MENU button until
17. V program might be providing more than one set of captions or one set of text To set your TV to display captions or text 1 With the TV turned on press the MENU button until Special menu will be displayed 2 The Closed Caption item be selected To turn captioning on use the AVOL buttons to select Captions C1 or C2 or Text T1 or T2 At the time these instructions were written only C1 is normally available but feel free to try the other selections 3 Wait 10 seconds or press the MENU button to return to normal TV viewing Your setting will remain intact until you change it 2 1 Special gt Closed Caption C1 CC on Mute Off Power Restore Off Parental Control Ch Labels 4 To Press Special EJ Closed Caption CC on Mute Off Power Restore Off Parental Control Ch Labels To Press Special Closed Caption CC on Mute Power Restore Parental Control Ch Labels 4 To Press Select 4 Adjust MNext Select 4 gt Adjust Next Select Adjust Next 48 Chapter 5 Additional Features CC on Mute When the sound is muted user can select the caption display It will display the caption content instead of sound mute 1 With the TV turned on press the MENU button until Special menu will be displayed 2 Use the WCHA buttons to select CC on Mute item 3 Use the VOLP buttons to select C1 or C2 Special E3 tejo Special Py Special Closed Capt
18. a VCR using the Video Audio input you will want to be able to view the signal from the component To do this you will need to switch from the TV input to the Line1 Line2 Line3 S Video Input as follows 1 With the TV on press the MENU button twice then Set Up menu will appear 2 Use the WCHA buttons to select Input 3 Press the AVOL buttons to change from TV to Linel Line2 Line3 S Video 4 Wait 10 seconds or press the MENU button to return to normal TV viewing 3 1 Ar NEA PN t eko Language English Language English Language English Reception Air Reception Air gt Input Linet Memorize Channels Add Delete Channels Input TV Memorize Channels Add Delete Channels gt Input TV Select 4 Adjust MNext Select 4 Adjust Next Select 4 Adjust Next Language English Language English Language English gt Input Line2 Input Line3 gt Input S Video Select 4 Adjust ENext Select lt 4 Adjust ENext Select 4 Adjust Next Note When you watch TV in S video mode Audio jack must be connected to AV2 terminal Achre 3 Operating Your TV Adjusting Video Settings You may wish to adjust the video settings e g contrast or color to obtain the most pleasing pic ture To do so follow these directions 1 With the TV on press the MENU button then Video menu will appear 2 The Settings it
19. another Time function or press the MENU button to return to normal TV viewing Set Clock Set Clock 12 00AM Wake Up Time Wake Up Time Off Time t Off Time Set Clock 12 00 AM Wake Up Time 06 30AM Off Time A Sleep Timer ii Sleep Timer Sleep Timer Select 4 Adjust Next Select 4 Adjust Next Select 4 Adjust Next Chapter 4 Using Timer Functions Setting the Off Time Tf you enter a time in the Off Time setting your TV will automatically turn off at that time Follow these instructions to set the Off Time 1 With the TV turned on press the MENU button until Time menu will be displayed 2 Use the WCHA buttons to select Off time item 3 Ifyou hold down either lt VOL or VOL gt button the corresponding numbers will change more quickly 4 When the setting is correct use the WCH A buttons to select another Time function or press the MENU button to return to normal TV viewing Set Clock 12 00AM Set Clock 12 00 AM Set Clock 12 00AM Wake Up Time 06 30AM Wake Up Time 06 30AM Wake Up Time 06 30AM Off Time sss Off Time gt Off Time 11 30PM Sleep Timer 0 min Sleep Timer 0 min Sleep Timer 0 min Select 4 Adjust ENext Select 4 gt Adjust Next Select gt Adjust Next Canceling the Wake up Time or Off Time Tf you would like to cancel the Wake up Time or the Off Time Press the lt VOL gt buttons until the
20. ble cart stand or table The television equipment may fall causing serious injury to a child or adult and serious damage to the equip ment Use only with a cart or stand recom mended by the manufacturer or sold with the television equipment Wall or shelf mounting should follow the manufacturer s instructions and should use a mounting kit approved by the manufacturer 6A An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn AN D E Important Safeguards 7 10 11 12 Slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the television equipment and to protect it from overheating these openings must not be blocked or covered The openings should never be blocked by plac ing the television equipment on a bed sofa rug or other similar surface This equipment should never be placed near or over a radiator or heat register This television equipment should not be placed in a built in installation such as a bookcase unless proper ventilation is provided This television equipment should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supplied to your home consult your television dealer or local power company This television equipment is equipped with
21. d video settings MENU Use this button to turn the TV s menu system on and off DISPLAY Use this button to display the channel number and status INPUT Use this button to select the TV s signal source VIDEO Use this button to display video adjustment items 0 9 Use these buttons to change channels 10 SLEEP Use this button to program the TV to turn off after a certain time 11 PREVIOUS Use this button to return to the previous channel you were watching Installing your remote control batteries 1 Open the battery compartment on the back of the remote control 2 Install two AA size batteries not included as shown Make sure the and terminals are oriented correctly 3 Replace the cover Notes Do not mix different types of batteries or mix an old and a new battery Remove and replace weak batteries Weak batteries can leak and damage your controller Dispose of batteries properly never throw them into a fire Point your remote at the receiver on the center of the front of the TV Make sure the receiver is not blocked The remote control can operate up to 30 feet away from the TV if you are directly facing the front of the TV Operating distance diminishes as you move to the sides of the TV Chapter 1 Overview of Your Equipment EB Connecting an Antenna or Cable to Your TV Your TV will provide you with the best performance if you connect it to an external antenna or
22. dio Mode Bass Treble gt Balance mExit Select 4 Adjust mExit Chapter 6 Adjusting the Sound CHAPTER Troubleshooting Your Daewoo television is designed to give you trouble free performance for many years If you have a problem with your TV try the solutions listed below Tf the suggestions listed below do not solve your problem contact your Daewoo dealer or an autho rized Daewoo service center There is no picture or sound or the TV dosen t turn on e Make sure the TV is plugged in e Make sure the MUTE is not set e Make sure the power is on e If there is neither picture or sound unplug the TV for 30 seconds then plug it in and try again There is no picture or sound on some UHF channels e Try another station If the other stations are OK it may be a station problem e Check that the antenna is connected is in good working order has no broken wires and is adjust ed correctly e See if anything is interfering with the antenna signal e Make sure the AIR CABLE setting is correct The sound is OK but the picture is poor e Try another station If the other stations are OK it may be a station problem e Check that the antenna is connected and is in good working order has no broken wires and is adjusted correctly The picture is OK but the sound is poor Try another station If the other stations are OK it may be a station problem e Check that the antenna is connected is in good working ord
23. e TV will tune to the new channel when you enter the second digit of the channel The PREVIOUS button will take you instantly to the last channel you were watching To change the volume of the TV set use the lt VOLP buttons on the remote conteroller or on the front panel To quickly turn off the sound press the MUTE button on the remote The MUTE will appear on screen colored green To return the vol ume to its previous level press MUTE again GB chapter 3 Operating Your TV Changing the TV s Channel Memory Your TV s memory determines the channels that are available using the WCH A buttons You can add channels to this memory or remove them from memory If a channel is removed from memory you can tune to it with the number buttons but you cannot tune to it with the WCH A buttons Tf there are just one channel memorized then the Add Delete Channels function will search the whole channels But if there are two or more channel memorized then the Add Delete Channels function will search the memorized channels only Adding Deleting a channel to memory 1 Use the number buttons to tune to the channel 2 Press the MENU button twice then Set Up menu will display 3 Use the WCHA buttons to select Add Delete Channels then use the lt VOL buttons to enter the Add Delete Channels process 4 If the channel is not in memory then use the VOL buttons to add the channel from memory 5 I
24. em will be selected Use the AVOL buttons to turn Settings to Preset or Custom 3 Use the WCH A buttons to select the video setting you wish to adjust Descriptions of the video settings are on the next page Use the AVOL buttons to adjust the video setting to the level you prefer Use the WCH A buttons to select another video setting to adjust When you are finished press the MENU button to return to normal TV viewing N Oo Oo f Video button on the Remote Controller can do the same function Settings gt Settings Preset Settings Contrast Contrast Contrast Brightness Brightness Brightness Sharpness Sharpness Sharpness Color Color Color Tint Tint Tint Select Adjust Select 4 Adjust Next Select 4 Adjust E Next 4 5 6 Contrast Brightness Chapter 3 Operating Your TV 13 Returning to the factory settings If you would like to return to the original video settings as they were calibrated at the factory fol low these steps 1 With the TV on press the MENU button then Video menu will appear 2 Press the lt VOLP buttons to set the Settings to Preset The TV will remember the Custom settings you had previously chosen When you set Settings to Custom again your previous custom settings will be restored Settings Settings Contrast Contrast Brightness Brightness Sharpness Sharpness Color Color Tint Tint Select 4 Adjust Next Select Adjust mNext
25. er has no broken wires and adjusted correctly There is poor reception on some channels e Try another station If the other stations are OK it may be a station problem e Check that the antenna is connected is in good working order has no broken wires and is adjust ed correctly You cannot tune to a cable channel e Make sure the AIR CABLE setting is correct The channel may not be programmed into memory The picture rolls slants shows lines is grainy has poor color or has ghosts e Try another station If the other station are OK it may be a station problem e Check that the antenna is connected is in good working order has no broken wires and is adjust ed correctly e See of anything is interfering with the antenna signal The remote control does not work e Make sure the TV is plugged in e Make sure there are fresh batteries in the remote control e Make sure there is nothing blocking the remote control signal Es Chapter 7 Troubleshooting WARRANTY gt e Warranty Daewoo Electronics Corporation of America warrants each new electronic prod uct manufactured by it to be free from defective material and workmanship and agrees to remedy any such defect or to furnish a new part at the Company s option in exchange for any part of any unit of its manufacture which under normal installation use and service disclosed such defect pro vided the unit is delivered by the owner to us or to our authorized
26. f the channel is in memory then use the AVOL buttons to delete the channel from memory 6 If you are going to delete other channel then press the WCH A buttons until desired channel is selected And press the VOL buttons to delete the channel 7 Wait 10 seconds or press the MENU button to return to normal TV viewing Add Delete Channels Air 11 This channel is not in memory Press VOL lt gt to add Press CH for other channels Press MENU to return to Set Up menu gt Language English Reception Air Memorize Channels Add Delete Channels Input TV Select amp Adjust MNext Add Delete Channels Air 11 This channel is in memory Press VOL lt gt to delete Press CH for other channels Press MENU to return to Set Up menu Displaying the Current Channel Language Reception Air Memorize Channels Add Delete Channels Input TV Select 4 Adjust MNext Add Delete Channels Air 11 This channel is in memory Press VOL lt gt to delete Press CH for other channels Press MENU to retum to Set Up menu 1 To quickly see the current channel number and status press DISPLAY button on the remote control The current channel number and status will be displayed Chapter 3 Operating Your vi Changing the TV s Input Normally your TV displays the signal coming through the antenna terminal However If you ve connected another component to your TV such as
27. hrough openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the television equipment 16 Do not attempt to service this television equip ment yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 17 Unplug this television equipment from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is dam aged or frayed b If liquid has been spilled or objects have fall en into the television equipment c If the television equipment has been exposed to rain or water d If the television equipment does not operate normally by following the operating instruc tions Adjust only those controls that are cov ered by the operating instructions as an improper adjustment of other controls may result in damage and will often require exten sive work by a qualified technician to restore the TV receiver to its normal operation e If the television equipment has been dropped or the cabinet has been damaged 18 19 20 f When the television equipment exhibits a distinct change in performance this indi cates a need for service When replacement parts are required be sure the service technician has used replacement parts specified
28. ings gt No Rating Unblock No Rating Unblock Ext Source Unblock Ext Source Unblock Change Password gt Change Password Select 4 Adjust mPrev Select 4 Adjust mPrev Chapter 5 Additional Features EB No Ratings means 1 When V chip data is error 2 When any ratings are not deleted 3 Received a rating of None like news sports and emergency broadcast signals Mini Glossary MOVIE RATING SYSTEM X Hard Core Films Not for children under age 17 under any circumstance Strong sexual content NC 17 Restrictd viewing Same as X rating R Restrictd viewing Not for children under age 17 Strong element of sex and or violence PG 13 Parental Guidance Program is inappropriate for preteens with a greater degree of Suggested offensive material than a PG rated program PG Parental Guidance Content is such that parents may not want their children to view the Suggested program G General Audience Content not offensive to most viewers NR Not Rated A motion picture that chid not receive a rating for a varicty of possible reasons TV PARENTAL GUIDELINE RATING SYSTEM TV MA Mature Audience Only Adults only may contain Strong Dialog Bad Language Sex TV 14 Parents Strongly Unsuitable for childern under 14 may contain Strong Dialog Bad Cautioned Language Sex and Violence Scenes TV PG Parental Guidance Unsuitable for younger childern may contain Suggestive Dialog S
29. ion Closed Caption Closed Caption CC on Mute CC on Mute gt CC on Mute Power Restore Power Restore Power Restore Parental Control Parental Control Parental Control Ch Labels To Press Ch Labels To Press Ch Label To Press Select Adjust ENext Select Adjust MNext Select Adjust Next Special EJ Closed Caption CC on Mute Power Restore Parental Control Ch Labels To Press Select Adjust mNext Power Restore User can select the On Off status when the power cord put into the wall outlet If user have a cable box with AC outlet then user can connect the TV power cord to the AC outlet and control the TV without TV remote control This function is rarely used for home use so special care is needed while using 1 With the TV turned on press the MENU button until Special menu will be displayed 2 Use the WCHA buttons select Power Restore item 3 Use the lt VOLP buttons to select On or Off Special E Special B g Special EJ Closed Caption C1 Closed Caption Closed Caption CC on Mute C1 OC on Mute OC on Mute Power Restore Off Power Restore Power Restore Parental Control Parental Control Parental Control Ch Labels To Press Ch Labels To Press Ch Labels To Press Select Adjust mNext Select Adjust mNext Select Adjust mNext Chapter 5 Additional Features 19 Parental Control Settings This item helps parents to set
30. is cable into a splitter avail able at your local electronics store Connect one coaxial cable between one OUT terminal on the splitter and the IN terminal on the converter box Connect another coaxial cable between the other OUT terminal on the splitter and the B IN terminal on an A B switch available at your local electron ics store Connect a third coaxial cable between the OUT terminal on the converter box and the A IN erminal on the A B switch Finally connect a coaxial cable between the OUT terminal on the A B switch and the antenna terminal on the back of your TV om E z B 4 cm y o TI bW 2 b SB H L j A 254 Cc a d Si N ol C Converter Box When the A B switch is in the A position you need to change channels on the converter box and your TV should be tuned to channel 3 or 4 when the A B switch is in the B position you can change channels on the TV Connecting Other Pieces of Equipment You may want to connect a VCR laser disc player satellite receiver or another type of equipment to your TV We recommend that you follow the instructions included with the piece of equipment you wish to connect Safety Note If you plan on being away from your home for an extended period of time o
31. nel So MTS feature allows you to improve your TV viewing with high fidelity stereo sound SAP Second Audio Program used to transmit a second language of other audio information If your TV receives a stereo sound or SAP broadcast when the TV is turned on select other channel or press the RECALL button on the remote control the word Stereo or SAP is displayed on the screen Listening to stereo sound 1 With the TV turned on press the MENU button until Audio menu will be displayed Use the WCH A buttons select Audio Mode item Press the VOL buttons repeatedly until Stereo is displayed Press the button twice or wait few seconds to return to normal TV viewing ao fF WwW KN Your setting will remain intact until you change it Your TV will then automatically reproduce either stereo or monaural sound whichever is broadcast Audio Mode Audio Mode Stereo Bass Bass Treble Treble m Balance Balance Select Adjust meExit Select Adjust meExit Listening to second Language 1 Follow steps 1 2 in Listening to stereo sound above 2 Press the lt VOLP buttons repeatedly until SAP is displayed 3 Press the MENU button twice or wait few seconds to return to normal TV viewing 4 Ifa SAP broadcast is received you will hear only the second language from the speaker Audio Mode Bass Treble Balance Select Adjust mExit Chapter 6 Adjusting the
32. or Picture Tube DTQ 25S5FC 1 year 90 days 2 years DTQ 27S5FC 1 year 90 days 2 years Warranty EB This instrument is listed by Underwriter s Laboratories Inc It is designed and manufactured to meet rigid U L safety standards against X radiation fire casualty and electrical hazards BGG As an ENERGY STAR Partner DAEWOO Electronics has determined that this product or product model meets the ENERGY STAR guidelines for energy efficiency Daewoo Electronics Corporation America 120 Chubb Avenue Lyndhurst NJ 07071 For more information about this or other Daewoo products please call 1 800 DAEWOO8 P N 48586011E107 RO
33. our TV s volume to activate selections in the menu system or to change audio and video settings 4 MENU Use this button to turn the TV s menu system on and off 5 Remote control receiver This receiver receives a signal from your remote control Do not block it 6 VIDEO IN jack Use this jack to receive a video signal from another A V component 7 AUDIO IN jack This receiver uses this jack to receive an audio signal from another A V componet 2 Chapter 1 Overview of Your Equipment Your TV s Back Panel 1 Antenna terminal ANT Use this terminal to attach an antenna or cable system to your TV 2 VIDEO IN This terminal allows the TV to receive a video signal from another component such as a VCR 3 AUDIO IN This terminal allows the TV to receive an audio signal from another component such as a VCR 4 S VIDEO IN This terminal allows the TV to receive a S VIDEO S VHS signal from S VIDEO S VHS out put terminal of another component Chapter 1 Overview of Your Equipment EB Your Remote Control SLEEP 0 PREVIOUS DISPLAY INPUT VIDEO GW chapter 1 Overview of Your Equipment POWER Use this button to turn your TV on or off MUTE Use to turn the TV s sound on and off wCHa Use these buttons to change channels on your TV or select items in the menu system lt VOL gt Use these buttons to change your TV s volume to activate selections in the menu system or to change audio an
34. pare 25S5FC pare 27S5FC CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk electric shock The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and servicing instructions in the literature accompanying the appliance WARNING TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE CAUTION CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT NOTE TO CATV SYSTEM INSTALLER THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER S ATTENTION TO ARTICLE 820 40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND IN PARTICULAR SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL CAUTION The AC power cord provided with this product is polarized one blade wider than the other To prevent electrical shock match wide blade of plug to wide slot fully inse
35. pter 5 Using the Special Features gt gt s ses ses ses eee sestre coe seo cee cee ees cee ceo 18 Changing the Language of the On Screen Menus scence cee see eee eee eee eias ae ee te eens nes riea aami eiai 18 Captioning cetei ada aii ARNa ai E eben oa canis aE o dec Ea A e seca servants read 18 CG on Mite crenn ear RER GA E ER e A E ROEN 19 Power Restore 19 Parental Control Settings Description of Parental Control Settings s ss rrartere rrareereerenrrnresrrerneres 20 21 Chlaes oer aa AE A E ted eases cosandetg aioe AE lemes ieee ares oesedaiee 23 Chapter 6 Adjusting the Sound es ss see set cee eee ceeeee eee cee tse terser eee eee eee e25 Selecting stereo SAP ceeseecceseeenen ee NA eee neat ee ee SAA N AARET EGE ERE SEA EG TREE EES ESDEE EEA REER 25 Adjusting the Bassa veseo tee aan thot Ses eta i dO ee ee Nn sed ie iN eh eG Adjusting the Treble niread E a eta Sica EE E E 27 Chapter 7 Troubleshooting Eia ra AA PAP E a aie a ea a a i r B Table of Contents SEB Overview of Your Equipment Your TV comes with a remote control The section below summarizes the buttons controls and ter minals that you will use with your TV Your TV s Front Panel AV3 IN rAUDIO VIDEO _L MONO R 1 POWER Use this button to turn your TV on or off 2 wCHa Use these buttons to change channels on your TV or to select items in the menu system 3 lt VOLP gt Use these buttons to change y
36. r if a thunderstorm is approaching you should unplug your television and you may wish to disconnect your TV from a rooftop or satellite antenna You do not need to disconnect your TV from a cable system 8 chapter 2 Connecting an Antenna or Cable to Your TV Operating Your TV Once you have connected your TV to an antenna or cable system plugged the TV in and put batter ies in the remote you are ready to use the TV The first thing you should do is to program your TV so it memorizes all of available channels Turning Your TV On 1 To turn your TV on press the POWER button on the remote control You can also use the POWER button on the front panel Make sure your TV is plugged in before you try to turn it on Programming Your TV s Channel Memory Your TV s memory determines the channels that are available using the CH buttons If a chan nel is not in memory you can tune to it with the number buttons but not with the W CH A buttons Follow these steps to program your TV s memory 1 With the TV on press the MENU button twice then Set Up menu will appear 2 Use the WCHA buttons to select Reception then use the lt VOLP buttons to select Air or Cable If you connected an antenna to your TV select Air If you connected a cable system select Cable 3 Use the WCHA buttons to select Memorize Channels then use the lt VOL buttons to enter the Memorize Channels process
37. rt the AC plug into a stan dard 120V 60Hz polarized outlet NOTE Never connect the plug to an electrical source other than one providing 120V 60Hz power Use only the attached power cord If the polarized AC cord does not fit into a non polarized outlet do not cut or file the blade You are responsible for hav ing the obsolete outlet replaced with a polarized outlet Tf you feel a static discharge when touching the unit and the unit does not function simply unplug the unit from the outlet When you plug the unit back in it should work normally Do not install power cords near any heating element or cooking appliances IMPORTANT SAFEGUARDS PLEASE READ ALL THESE INSTRUCTIONS REGARDING YOUR TELEVISION EQUIPMENT AND RETAIN FOR FUTURE REFERENCE FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE TV RECEIVER 1 Read all of these instructions Save these instructions for later use Unplug this television equipment from the wall outlet before cleaning Do not use liquid clean ers or aerosol cleaners Use a damp cloth for cleaning Do not use attachments not recommended by the television equipment manufacturer as they may result in the risk of fire electric shock or other personal injury Do not use this television equipment near water for example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool or the like Do not place this television equipment on an unsta
38. tons to select lt VOL gt buttons to adjust You can set individual settings with lt VOLP gt buttons The Movie Ratings set the standard for movie video and other media excluding TV programs Use the WCH A buttons to select lt VOL buttons to adjust The No Rating item toggles between Unblock and Block This item determines whether to block or not the programs which are not rated by Movie Ratings and TV Guidelines Use VOL buttons to change the settings The Set Password item let you change the password for entering Parental Control item You had better change the initial password 0000 Use lt VOL buttons to enter the pass word in ut display and use the number buttons 0 9 to enter new password After you entered the new password confirmation display will appear Type again the password Parental Control Rating All FV D L S V Parental Lock On TINA gt TV Guidelines TV14 I Movie Ratings TV PG No Rating Unblock TV G Ext Source Unblock TV Y7 Change Password TV Y V Block Select 4 gt Adjust mPrev Select 4 Adjust Prev Parental Control Parental Lock On x TV Guidelines NC 17 gt Movie Ratings R No Rating Unblock oy Ext Source Unblock Change Password AR Vv Block Select Adjust mPrev Select 4 Adjust MIPrev Parental Control Parental Control Parental Lock On Parental Lock On TV Guidelines TV Guidelines Movie Ratings Movie Rat
39. uggested Bad Language Sex and Violence Scenes TV G General Audience Considered suitable for all audiance children may watch unattended TV Y7 Children 7 and over Consider suitable for children over 7 may contain Fantasy Violence Scenes TV Y Children Consider suitable for all children under 7 years old Chapter 5 Additional Features Ch Labels This feature allows you to enter a 4 letter channel identifier of your choice that will appear over the channel mumber dispaly The labeling can be anything you want 1 With the TV turned on press the MENU button until Special menu will be dispalyed KR U N space n Use the WCH A buttons to select Ch Labels item Press VOL on the remote control or on the TV to select the 1st character space Press YCH A repeatedly until the 1st character A in this example appear in the 1st charater Press VOL once to enter the 1st character and to advance to the next character space 6 Repeat steps 4 5 to enter the 2nd 3rd and 4th characters B C D in the this example and when you press VOL for the last time the channel label has been stored in the memory Special gt Closed Caption CC on Mute Power Restore Parental Control Ch Labels 4 Adjust Special EJ Closed Caption CC on Mute Power Restore Parental Control Ch Labels Select 4 Adjust Closed Caption CC on Mute Power Restore
40. xt Select 4 Adjust mNext Chapter 4 Using Timer Functions Using the Special Features This section contains descriptions of the more advanced features of your TV Changing the Language of the On screen Menus You can choose to display the on screen menus in English Spanish French To change the on screen language 1 With the TV on press the MENU button twice then Set Up menu will appear 2 The Language item will be selected Press the AVOL buttons to select the language you want to use English Espa ol Fran ais 3 To return normal TV viewing press the MENU button to return to normal TV viewing 2 1 Installer weko Langue Fran ais R ception Air M moriser Cha nes gt Idioma Espa ol Recepci n Aire Memorizar Canales A adir Borrar Canales Entrada TV gt Language English Reception Air Memorize Channels Add Delete Channels Input TV Ajouter Supprimer Chaines Entr e Tele Choix A R gler W Suivant Select 4 Adjust Next Escoger 4 gt Ajustar Otro Captioning Many TV shows contains Closed Caption These captions are hidden words that can be displayed on your TV screen There are two types of these words captions usually follow the action on screen providing a written version of the dialogue narration and sound effects text is not usually related to the action on screen often providing information such as news or weather A T
Download Pdf Manuals
Related Search