MediaFORM CD 3703 Burner
Contents
1. Germany office Home office MF Optical GmbH MediaFORM Inc Albert Schweitzer Ring 23 122 Oscar Way 22045 Hamburg Germany Chester Springs PA 19425 Tel 49 40 668 535 99 Tel 610 458 9200 Fax 49 40 668 535 98 Fax 610 458 9554 e mail info amp mfoptical de Email documentation O mediaform com www http www mfoptical de www http www mediaform com Page 1 CD 3000 Series Operator s Guide Document Revision 100102 End User License Agreement e You have acquired a device 3000 Series CD R RW duplicator that includes software licensed by MediaFORM from Microsoft Licensing Inc or its affiliates MS Those installed software products of MS origin as well as associated media printed materials and online or electronic documentation SOFTWARE are protected by international intellectual property laws and treaties The SOFTWARE is licensed not sold All rights reserved e IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT EULA DO NOT USE THIS DEVICE OR COPY THE SOFTWARE INSTEAD PROMPTLY CONTACT MEDIAFORM FOR INSTRUCTIONS ON RETURN OF THE UNUSED DEVICE S FOR A REFUND ANY USE OF THE SOFTWARE INCLUDING BUT NOT LIMITED TO USE ON THE DEVICE WILL CONSTITUTE YOUR AGREEMENT TO THIS EULA OR RATIFICATION OF ANY PREVIOUS CONSENT e GRANT OF SOFTWARE LICENSE This EULA grants you the following license You may use the SOFTWARE only on the DEVICE gt NOT FAULT TOLERANT2. POWER RECEPTACLE POWER SWITCH I Page 7 CD 3000 Series Operator s Guide Document Revision 100102 Location Of CD 3702 Components AUTOMATED LOADING UNLOADING M V t SPINDLE ARM INPUT BIN Pi L RIVE BAY CD 3702 7 y BASE UNIT KEYPAD LCD DISPLAY o AUTOMATED LOADING UNLOADING ARM All other ports are for service personnel use only VOLTAGE SELECTOR SWITCH 4 VAC in volt in ON OFF SWITCH Page 8 CD 3000 Series Operator s Guide Document Revision 100102 Location Of CD 3703 Components OUTPUT SPINDLE INPUT AREA 4 DRIVE BAYS LCD DISPLAY Bo KEYPAD AUTOMATED LOADING UNLOADING ARM All other ports are for service personnel use only VOLTAGE SELECTOR SWITCH 4 VAC in volt in ON OFF SWITCH Page 9 CD 3000 Series Operator s Guide Document Revision 100102 Location Of CD R RW Recorder Parts And Controls 1 Disc tray Discs are loaded and removed from this tray Pressing the eject button will open the tray when the power is switched on to the 3000 Series 2 Emergency eject pinhole In the event that the disc tray will not open by pressing the eject button insert the tip of a large paper clip into this hole and push Earphone jack Volume Control 5 Read and write status LEDs These indicators light up when the recorder is reading or writing 6 Eject button This butto
3. The factory setting for this function is 40x When selected the Select Recording Speed feature allows you to set the copying speed as determined by the capabilities of the recorders installed in the 3000 Series Press the 0 key to select 16x or the 1 key for 24X or the 2 key for 40X After pressing any of those keys the screen will now read 2 x RECORDING SPEED SELECT COPY OR COMPARE Press the 9 key on the keypad Something similar to the following will be displayed in sequence DEVICE 1 0 0 This displays the status of the last disc copied or compared in each of the 3000 Series recorders If the last operation performed was successful the screen will report OK If problems were encountered an error message will be displayed Page 20 CD 3000 Series Operator s Guide Document Revision 100102 Creating Hard Disk Image The CD 3000 comes equipped with an internal hard disk drive which can be used to store copies of master discs for later recording or comparing Each master is saved as a single image file Up to four images can be stored on the hard disk at one time A hard disk image is useful as a convenient way of copying standard master discs For example create hard disk images for three or four master discs which are needed on a regular basis and access them to make copies as required Creating A Single Hard Disk Image Although the CD 3000 s internal hard disk c
4. gt J m e Load as many blank discs as are required into the input bin e Press the COPY key on the keypad The screen will now read a O I U e Press the START YES key to begin copying from the hard disk image to the blank discs in the recorders Depending on the format type of the image something similar to the following will be displayed on the screen ENTER QUANTITY e Enter the quantity of discs you wish to copy up to 100 COPYING GOOD 0 BAD 0 OF 0 Progress will be displayed on the screen during the operation COPY OK PRESS START GOOD 0 BAD 0 OF 0 e Press the START YES key and you will be returned to the main Operating screen 0 m m m O O O U lt O JJ O O U gt J m Page 26 CD 3000 Series Operator s Guide Document Revision 100102 Note If discs failed to copy properly they will be dropped in the reject area in front of the drive bay These discs should not be used To help you determine the nature of the problem error messages can be displayed by pressing the 9 key on the keypad Multiple Images Enabled To make copies from hard disk images that were previously created with the Multiple Images feature enabled the steps are as follows From the main operating screen depicted below SELECT COPY OR COMPARE Load as many blank discs as are required into the input bin Press the COPY key on the keypad The screen
5. emerge from time to time Should you encounter a disc which does not employ a copy protection scheme that you cannot copy on your CD 3000 MediaFORM will do its best to promptly add support for this format Dealing with custom formats however may be subject to a development charge Keeping track of how the various formats relate to each other can be confusing For example the CD 3000 can copy all CD ROM Mode 1 discs this includes ISO 9660 HFS Hybrid Rock Ridge and many other types of file systems As a result the CD 3000 will most likely copy CD formats not listed in the table below If you require further assistance please contact MediaFORM s technical support department at 610 458 9200 or email support mediaform com CD 3000 Supported Formats CD R RW ISO 9660 CD ROM Mode 1 amp Mode 2 CD ROM XA Mode 2 Form 1 amp Form 2 Hybrid ISO 9660 HFS Single session Hybrid ISO 9660 HFS Rock Ridge Multisession Mixed Mode Disc at Once and Track at Once CD I Form 1 amp Form 2 Rock Ridge Native O S s NT DOS OS 2 UFS HFS CD Extra Mac O S SUN AS 400 AIX etc Video CD Romeo Photo CD Joliet Picture CD Bootable CD CD G Karaoke CD Page 38 CD 3000 Series Operator s Guide Document Revision 100102 CD 3000 Supported Formats CD ROM Mode 1 High Speed CD RW is not supported to write Page 39
6. Series is extremely versatile and offers many useful and powerful features Function Keys Various uses for the 3000 Series will be explained throughout this Operator s Guide The following section explains the purpose of the function keys The numeric keys on the keypad have special functions when the main operating screen is displayed SELECT COPY OR COMPARE OD e Press the 0 key on the keypad The screen will now read MODE COPY 1 SI MULATE 2 The factory setting for this function is copy The simulate mode is a diagnostic tool that is useful for testing the readability of a master disc without actually writing to blank discs loaded into the recorder It is also helpful for training purposes and for experimenting with various system functions e Press the 1 key to select copy or the 2 key to select simulate After pressing either key you will be returned to the main operating screen O e Press the 1 key on the keypad Something similar to the following will be displayed on the screen in sequence A NTSA 1 004n 07 31 02 SOFTWARE REV CARD 1B This is the version information of the firmware currently installed on the 3000 Series IMAGE SIZE 255 MB TI ME 12 19 DATE 07 0 8 0 2 Page 15 CD 3000 Series Operator s Guide Document Revision 100102 The size creation date and time of all the hard disk images stored in the 3000 Series are displayed in sequence If the
7. THE SOFTWARE IS NOT FAULT TOLERANT MEDIAFORM HAS INDEPENDENTLY DETERMINED HOW TO USE THE SOFTWARE IN THE DEVICE AND MS HAS RELIED UPON MEDIAFORM TO CONDUCT SUFFICIENT TESTING TO DETERMINE THAT THE SOFTWARE IS SUITABLE FOR SUCH USE gt NO WARRANTIES FOR THE SOFTWARE THE SOFTWARE is provided AS IS and with all faults THE ENTIRE RISK AS TO SATISFACTORY QUALITY PERFORMANCE ACCURACY AND EFFORT INCLUDING LACK OF NEGLIGENCE IS WITH YOU ALSO THERE IS NO WARRANTY AGAINST INTERFERENCE WITH YOUR ENJOYMENT OF THE SOFTWARE OR AGAINST INFRINGEMENT IF YOU HAVE RECEIVED ANY WARRANTIES REGARDING THE DEVICE OR THE SOFTWARE THOSE WARRANTIES DO NOT ORIGINATE FROM AND ARE NOT BINDING ON MS Note on Java Support The SOFTWARE may contain support for programs written in Java Java technology is not fault tolerant and is not designed manufactured or intended for use or resale as online control equipment in hazardous environments requiring fail safe performance such as in the operation of nuclear facilities aircraft navigation or communication systems air traffic control direct life support machines or weapons systems in which the failure of Java technology could lead directly to death personal injury or severe physical or environmental damage Sun Microsystems Inc has contractually obligated MS to make this disclaimer No Liability for Certain Damages EXCEPT AS PROHIBITED BY LAW MS SHALL HAVE NO LIABILITY FOR ANY INDIRECT SPECIAL CONS
8. WATERMARK The watermark is a unique electronic fingerprint These fingerprints allow discs to be traced back to the specific unit and even to the recorder that wrote them Watermarks are useful ways of dealing with unauthorized copying authenticating discs as well as helping to diagnose copying problems Press the START YES key to read the watermark If the STOP NO key is pressed you will be prompted to Read ATIP D m gt o gt VU 3 When selected the ATIP function allows you to determine the manufacturer of the CD R placed in drive 1 of the 3000 Series If you pressed the Stop No key at you will be prompted to Set the Drive Order SET DRIVE ORDER Press the STOP NO key 1f you do not want to reset the drive order Press the START YES key and you will then see the following screen OPENING DRIVES All of the drives will open at this time TESTING DRIVE STATUS CLOSE DRIVE TRAY 1 Close the drive tray of the drive you would like to be drive number 1 It can be any one of the drives You will then see the following screen TESTING DRIVE STATUS DRIVE 1 DETECTED Close the remaining drives in the order that you would like them to read TESTING DRIVE STATUS CLOSE DRIVE TRAY 2 Page 19 CD 3000 Series Operator s Guide Document Revision 100102 Press the 8 key on the keypad The screen will now read SELECT RECORDING SPEED 0 16X 1 24X 2 40X
9. 102 Press the STOP NO key to exit Press the 5 key on the keypad The screen will now read START IMPORTI NG AUDI 0 STOP NO START YES By using the Audio Track Import feature audio compilation discs can be created one track at a time from one or more masters Manually place an audio master disc into drive number 1 Press the START YES key Press the number of the track you wish to import and press the START YES key Only one track may be imported at a time All of the tracks will create one master image on the hard drive Once you have imported all of the tracks copy the image you just created from the hard drive as you normally would Press the 6 key on the keypad Something similar to the following will be displayed in sequence 1 0 0 GENERIC CRD BP1700 v md00 RID 000902057089 This display is the device information for the recorder installed in the 3000 Series This includes it s host number model name and firmware version Press the 7 key on the keypad The screen will now read CLEAR HD Press the START YES key to clear the hard drive If the STOP NO key is pressed you will be prompted to set the System Time SET SYSTEM TI ME Press the START YES key to set the system time If the STOP NO key is pressed you will be prompted to Read Watermark Page 18 CD 3000 Series Operator s Guide Document Revision 100102 READ
10. ELECT COPY OR COMPARE Page 36 CD 3000 Series Operator s Guide Document Revision 100102 System Startup e Turn on the power to the CD 3000 Wait a minute or two while the system starts up The screen will now read MF INC DUPLI CATI ON MADE EASY Once complete the main operating screen is displayed on the screen SELECT COPY OR COMPARE e Turn on the power to the PC and the computer will recognize the CD 3000 s CD R RW recorders as valid devices Refer to the documentation that accompanied your premastering software for information on how to create CDs CAUTION SL The CD 3000 cannot be operated in its normal standalone mode when I attached to a PC Do not attempt to execute any commands using the keypad as this may lockup both the PC and the CD 3000 Page 37 CD 3000 Series Operator s Guide Document Revision 100102 Appendix A Supported Formats Originally designed for audio use the Compact Disc CD evolved quickly and now employs a wide variety of formats for audio data and multimedia applications The following is a list of the most popular formats currently supported by the CD 3000 Periodic firmware updates will be made available to deal with new formats as they appear To obtain the latest version of firmware contact your MediaFORM reseller or download the update from the MediaFORM web site www mediaform com Many CD formats are international or industry standards but variations on them may
11. EQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM OR IN CONNECTION WITH THE USE OR PURPOSE IN NO EVENT SHALL MS BE LIABLE FOR ANY AMOUNT IN EXCESS OF U S TWO HUNDRED FIFTY DOLLARS U S 250 00 Limitations on Reverse Engineering De compilation and Disassembly You may not reverse engineer de compile or disassemble the SOFTWARE except and only to the extent that such activity is expressly permitted by applicable law notwithstanding the limitation gt SOFTWARE TRANSFER ALLOWED BUT WITH RESTRICTIONS You may permanently transfer rights under this EULA only as part of a permanent sale or transfer of the Device and only if the recipient agrees to this EULA If the SOFTWARE is an upgrade any transfer must also include all prior versions of the SOFTWARE gt EXPORT RESTRICTIONS You acknowledge that SOFTWARE is of US origin You agree to comply with all applicable international and national laws that apply to the SOFTWARE including the U S Export Administration Regulations as well as end user end use and country destination restrictions issued by U S and other governments For additional information on exporting the SOFTWARE see http www microsoft com exporting Page 2 CD 3000 Series Operator s Guide Document Revision 100102 Table of Contents ABOUT MEDIAFORM INC scsisscssscssvssessccssdsoscoassasesceessceseascecesseadeesseansedesebecoesscavesetsceosscnsesdesedessessaacedseaseccsssesassessese 4 WHAT TO EXPECT F
12. Multiple Images feature is disabled the size of the current hard disk image is displayed VERI FY AFTER COPY SYSTEM OPTI ONS This displays the Verify After status of the 3000 Series The Verify After function will verify a copied disc against the master that it was burned from immediately after being copied MULTIPLE MAGES SYSTEM OPTI ONS This displays the Multiple Images status of the 3000 Series INSTALLED MEMORY 1020MB SYSTEM OPTI ONS This displays the installed memory of the 3000 Series TOTAL GOOD BAD SYSTEM OPTI ONS This is the 3000 Series internal counter It keeps track of the number of good and failed copies made by the unit since it was first activated Press the 2 key on the keypad You will see several functions scroll across the screen Select a function by pressing the corresponding number on the keypad Enable or disable the function by pressing the START YES or STOP NO key SELECT OPTION lt m J Tl lt gt Tl m JI O O U lt The factory setting for this function is disabled When enabled the Verify After feature automatically compares discs to the master disc or hard disk image after copying is completed Due to the nature of the various compact disc formats only CD ROM Mode 1 CD ROM Mode 2 CD ROM XA Mode 2 Form 1 and audio CD DA discs can be compared Page 16 CD 3000 Series Operator s Guide Document Revision 100102 ou 1 M
13. N E SMART METTE ORM hoos CD 3000 Series Operator s Guide CD 3000 Series Operator s Guide Document Revision 100102 Copyright Notice Copyright 1996 2002 by MediaFORM Inc All rights reserved This manual and the accompanying illustrations may not be copied reproduced electronically transmitted or translated into another language in whole or in part without the written consent of MediaFORM Inc MediaFORM CD2CD CD2CD PRO CD 5400L CD 5908 CD 5916 CD 3702 CD 3703 CD 3704 CD 3706P cdDIRECTOR AP 1001 AP 1301C Easi DAT and Easi AUDIO are trademarks of MediaFORM Inc Other trademarks referred to are the property of their respective trademark or registered trademark holders CD R RW Recorder Warranty Policy Individual CD R RW recorder manufacturers are responsible for the products they provide As a convenience MediaFORM will honor any service issue related to a defective recorder while under its respective manufacturers warranty providing that the recorder has been purchased from MediaFORM either directly or indirectly MediaFORM assumes no responsibility for products NOT purchased through MediaFORM Piracy The copying of audio video or software without the permission of the copyright holder is illegal MediaFORM Inc accepts no responsibility for the copyright use or misuse of this equipment It is the sole responsibility of the user to ensure that the legal rights of copyright in duplicating are respected
14. ROM YOUR MEDIAFORM CD DUPLICATOR occccccccncccncnnninnncnnnnnnnononononononononononenonenoneninininicininenos 4 ABOUT THIS MANUAL AAA E 4 GETTING STARTED occsssecesecccesdescsssscssesossesessecesssnsocssdeesessesusssdesecssssebeosus soseseseosesduvacsuenseeseessssuseodassenstdesesecessvosveosesss 5 WHAT SIN THE BOX sd ee eee en ideene 5 PACKING MATERIALS tddi 5 THE BEST PLACE TO PUT THE CD 3000 0 ccccccecccecececececececececececececececececececeveceveceveuevecsssueesesusesusceusesesesueseseseveeeeevens 6 SAFETY PRECAUTIONS Jie 6 LOCATION OF CD 3701 COMPONENTS ccccccccccccecccsuscscccseeceucesucceeccsesesesescecsesesueesesesesceseceusesusesescssessssessssusesuseesseaess 7 Front VieW ooonnnncnn nicicccccno ARO 7 Rear View rrnrrvvrvnnvrvrrsrenr EE NE RN 7 LOCATION OF CD 3702 COMPONENTS cccccccccccsececscsceccuccsuscsususususcsesusesusesueesusesusesususcecsceesusvecsveuesesesessesesseseseesseusss 8 Front View rrvvrvrnrrnvrnrsnnrr EE EN EE A TA 8 Rear View rrrrrvvrvnnrrnvrrsernrs eee eee 8 LOCATION OF CD 3703 COMPONENTS seiiiveineevike keen viee ak ciales 9 Front VIOM aS nar o 9 Fer Ven A ea seeeeevti ses A A 9 LCD Display Screen And Keypad eccccccececcssssesesesseseseeeseseseeseseseseceenensaeseseceesessaesesecseaeaseaeaseaeseeeeseaeneeaeaees 10 SMAMD RIVE 40X re 10 REMOVING PACKING RESTRAINTS sporasi ornans nina paa a a aa a a a aA ar AES EES ERES NA AE 11 INPUT BIN AND OUTPUT SPINDLE cccccccccccccccccceu
15. ULTI PLE MAGES SELECT OPTION The factory setting for this function is disabled When enabled the Multiple Images feature allows up to four images to be stored on the hard disk drive at one time This setting will remain in effect until disabled even after restarting the 3000 Series NS m To mr o 40 A O UU m om zo O a The factory setting for this function is enabled When disabled the Click Detection feature allows masters with small random errors to be read to the hard drive Caution should be taken when disabled as masters that would normally be rejected will be allowed to be read in Undesirable results may occur 3 COPY PROTECTI ON SELECT OPTI ON The factory setting for this function is disabled When enabled the Copy Protect feature will write copy protection information into data discs copied by the 3000 Series e Not used e Press the 4 key on the keypad The screen will now read START LOADER TESTER STOP NO START YES When selected the Loader Test Mode function allows you to manually control the robotic functions of the system for troubleshooting and testing purposes 0 G 1 1 2 A 3 R SELECT TEST The 0 key recalibrates the picking arm The 1 key will load a disc from the input spindle The 2 key unloads the disc The 3 key rejects the disc Page 17 CD 3000 Series Operator s Guide Document Revision 100
16. an store up to four images of master discs it is sometimes prudent not to use this Multiple Image feature and only allow one image to be created and stored For example using a single image simplifies the copying process This reduces the chance that an operator might make copies of the wrong discs by selecting the incorrect hard disk image To create a single hard disk image the steps are as follows From the main operating screen depicted below SELECT COPY OR COMPARE Press the COPY key The screen will now read FROM HD Press the STOP NO key The screen will now read COPY TO HD Press the START YES key The screen will now read in sequence LOADING MASTER GOOD 0 BAD 0 OF 0 Page 21 CD 3000 Series Operator s Guide Document Revision 100102 WAITING FOR DRIVES READY GOOD 0 BAD 0 OF 0 READ ME 75 GOOD 0 BAD 0 OF 0 MASTER ARCHI VED OK GOOD 0 BAD 0 OF 0 ARCHI VE OK PRESS START GOOD 0 BAD 0 OF 0 The master disc is now stored as an image on the hard disk Note If discs failed to copy properly they will be dropped in the reject area in front of the drive bay These discs should not be used To help you determine the nature of the problem error messages can be displayed by pressing the 9 key on the keypad e Press the START YES key and you will be returned to the main operating screen SELECT COPY OR COMPARE Note When the Multiple Images feature is
17. ccscccecscsecesuccsucesecesesesescessesesesusesusessecececeseesucesseusseussesssessseessesssesseess 11 SYSTEM STARTUP sinisisssrnnsssssvnnsserseersseneedessrvessekeensseneesesdsnkesessendesesneedegensneesernssnessendevnssdennedndaesedssdnedenandassevsanrsssneet 12 EOADNGADSG LL O EE 14 REMOVING A DISC AE satse cevcbsnteeded cevssensodnos cedaucbenscouveedadasuseucesties sag asvouaceeveedslesecensestess ES 14 GENERAL OPERATION scccsscsossesesssceseccssssctesessesdsseesbecesosesosssonccvdososccsdues osossescassbeneseceudetessend csesnoscdseuse osussdeeessoseosses 15 FUNCTION KEYS a en ee 15 CREATING HARD DISK IMAGE sine etater dad aent 21 Creating A Single Hard Disk Image orrnrenvnvnrnrnnvnrenvnrnnnnnvnnrnenennnsnvnrsnrnennnsenvnesnrnensssrsenesseresnrnessssrsenesnenennn 21 Creating Multiple Hard Disk Images orrvronvrrnnnrnnrnrnnrnvnnnnnrnnrnenennnnrnrnesnrnenassnrnnrnrnenssnrsrnesnrnesenesessrsrnesnenesn 23 ENABLING VERIFY AFTER eerorvrorvvnvvvnvnnnvnnnnvevnnnnrnnnnvnnnnnnrnnnnnnnvnnnvnnnnnnnnnnnnnnnnnvnvnnnvnnnnnnnnnennnnnnnnnnnnnnnnnnnnnnnnnnvnnenenennnenene 25 COPYING FROM A HARD DISK IMAGE coccccccccncnoncconononononononononononononononnnonnnnnnnnnnnonnnnnnnnnnnnnnnnnnnonnnnnnnnnnonononenenecinacenesos 26 Multiple Images Disabled rrnrnvrnvononrrnvvronrenvrnenavnnrnennrnernenarnernenernersenarnersenernersenasnessenasnessenssnessenssnessenssnessene 26 Multiple Images Enabled um missmrinsvsiaisnvinsieseimsnvienssaidsnvienseaims
18. de 2 CD ROM XA Mode 2 Form I and most CD formats can be compared Multiple Images Disabled To compare copied discs to a hard disk image that was previously created with the Multiple Images feature disabled i e from a single hard disk image the steps are as follows e From the main operating screen depicted below SELECT COPY OR COMPARE e Load the copied discs to be compared into the input bin e Press the COMPARE key on the keypad The screen will now read COMPARE AGAINST HD e Press the START YES key The screen will now read ENTER QUANTI TY Progress will be displayed on the screen during the operation COMPARI NG GOOD 0 BAD 0 OF 0 Upon successful completion the compared disc s will be ejected The screen will now read COMPARE OK PRESS START e Press the START YES key and you will be returned to the main Operating screen Page 29 CD 3000 Series Operator s Guide Document Revision 100102 SELECT COPY OR COMPARE Note If discs failed to copy properly they will be dropped in the reject area in front of the drive bay These discs should not be used To help you determine the nature of the problem error messages can be displayed by pressing the 9 key on the keypad Multiple Images Enabled To compare copied discs to a hard disk image that was previously created with the Multiple Images feature enabled the steps are as follows e From the main operat
19. disabled only one image can be saved on the hard disk If a new image is created the old one is overwritten Page 22 CD 3000 Series Operator s Guide Document Revision 100102 Creating Multiple Hard Disk Images The Multiple Images feature allows the CD 3000 s internal hard disk to store up to four master disc images The factory setting for this function is disabled To enable it and create multiple image files proceed as follows e From the main operating screen depicted below SELECT COPY OR COMPARE e Press the 2 key The screen will now read O VERI FY AFTER COPY SELECT OPTIONS 1 MULTI PLE I MAGES SELECT OPTIONS 2 CLI CK DETECTI ON SELECT OPTIONS 3 COPY PROTECTI ON SELECT OPTIONS e Press the 1 key to select multiple images The screen will now read MULTIPLE IMAGES MODE SELECT OPTI ON e Press the START YES key to enable Multiple Images MULTIPLE IMAGES SELECTED SELECT OPTION e You will then be returned to the main operating screen SELECT COPY OR COMPARE e Press the COPY key The screen will now read FROM HD e Press the STOP NO key The screen will now read OPY TO HD Page 23 CD 3000 Series Operator s Guide Document Revision 100102 e Press the START YES key The screen will now read IMAGE A 1 B 2 C 3 SELECT I MAGE e Select the number that will designate the location of your master The screen will then read i
20. fore copying begins The CD 3000 equipped with the SmartDRIVE 40X drives will only accept 10x CD ReWritable CD RW discs Page 33 CD 3000 Series Operator s Guide Document Revision 100102 Setting The Internal Clock The CD 3000 s internal clock is set at the factory for Eastern Standard Time observing daylight savings when applicable To set the internal clock the steps are as follows Press the 7 key on the keypad The screen will now read CLEAR HD Press the STOP NO and you will be prompted to set the System Time SET SYSTEM TI ME Press the START YES key if you would like to set the system time The screen will then read ENTER YEAR SETTING SYSTEM DATE Press the START YES key after each entry Om Hm 0 m um mz mz mz mz 3 4 4m m m m zo gt aI 3 z z z z QS 9O ZT OOLINS ais O gt O o z nc w lt loz lt c lt a lt lt gt m Ox 4 m 4 4 m m m m U U U U gt gt gt gt 4 4 4 4 m m m m You will then be returned to the main operating screen SELECT COPY OR COMPARE Page 34 CD 3000 Series Operator s Guide Document Revision 100102 Firmware Updates From time to time the CD 3000 s internal firmware may need updating to add new features or improve existing functions Firmware is easily updated by loading a Firmware Update CD into the system The latest ver
21. icator is in a climate controlled area free of dirt dust humidity excessive heat and electronic or electromagnetic interference Room temperature should be between 65 and 75 degrees Fahrenheit or between 18 and 23 degrees Celsius Place the CD 3000 on a solid steady work surface and allow sufficient room for all incidental work materials Provide at least six inches of clearance on all sides of the unit for ventilation Safety Precautions The system is shipped with a three prong power connector and must be used with a properly grounded AC receptacle DO NOT try to defeat the third ground prong All computer peripherals must be properly grounded and the CD 3000 is no exception The use of a power conditioner such as an Uninterruptible Power Supply UPS or a surge protector is highly recommended The minimum required size is 5 00VA Repairs or alterations should only be attempted by authorized factory trained technicians MediaFORM reserves the right to void the warranty if unauthorized service is performed Page 6 CD 3000 Series Operator s Guide Document Revision 100102 Location Of CD 3701 Components AUTOMATED LOADING UNLOADING 3 AA SPINDLE ARM e DRIVE BAY INPUT BIN gt Dun cp 3701 7 J LCD DISPLAY OUT SPINDLE AUTOMATED LOADING UNLOADING ARM ge INPUT BIN DRIVE BAY gt are for service r a E use SS CD 3701 ONLY pom JU T BASE UNIT
22. ing screen depicted below SELECT COPY OR COMPARE e Load the copied discs to be compared into the input bin e Press the COMPARE key on the keypad The screen will now read O O VU gt J m gt Q gt Z wn I U Y e Press the START YES key The screen will now read IMAGE A 1 B 2 C 3 SELECT MAGE e Select the image you would like to compare against by pressing 1 2 3 or 4 ENTER QUANTITY Progress will be displayed on the screen during the operation COMPARING GOOD 0 BAD 0 OF 0 Upon successful completion the compared disc s will be ejected The screen will now read Page 30 Document Revision 100102 CD 3000 Series Operator s Guide COMPARE OK PRESS START GOOD 0 BAD 0 OF 0 Press the START YES key and you will be returned to the main o Operating screen SELECT COPY OR COMPARE If discs failed to copy properly they will be dropped in the reject area in front of the drive bay These discs should not be used To help you determine the nature of the problem error messages can be displayed by pressing the 9 key on the keypad Note Page 31 CD 3000 Series Operator s Guide Document Revision 100102 Viewing SCSI Device Information To view the CD 3000 SCSI device information the steps are as follows e From the main operating screen depicted below SELECT COPY OR COMPARE e Press the 6 key Something similar to
23. n is used to open or close the disc tray Eu Page 10 CD 3000 Series Operator s Guide Document Revision 100102 Removing Packing Restraints The CD 3000 ships with a picker arm restraint to reduce the possibility of damage in transit This restraint must be removed before operation or power on Gently remove the foam tube from around the transfer arm Save the foam tube as you will need to return it to its place when transporting the unit in the future Input Bin And Output Spindle The input bin and output spindle serve as the containers to store up to 100 blank and recorded discs Page 11 CD 3000 Series Operator s Guide Document Revision 100102 System Startup Before duplicating can begin it is necessary to review a few details e Plug one end of the supplied power cord into the upper receptacle at the rear of the unit e Next verify that the voltage selector switch is set correctly It is located between the two power receptacles The CD 3000 supports both 115 VAC and 230 VAC at 50 60 Hz Please confirm that the appropriate voltage 115 VAC for North America has been selected CAUTION SL Always use properly grounded receptacles or severe damage to your system may result The use of a surge protector or Uninterruptible Power Supply UPS is highly recommended Page 12 CD 3000 Series Operator s Guide Document Revision 100102 Make sure you power on the unit using the switch seen belo
24. n sequence LOADING MASTER WAI TI NG FOR DRI VE READY GOOD 0 BAD 0 OF 0 MASTER ARCHI VED OK ARCHI VE OK PRESS START Page 24 CD 3000 Series Operator s Guide Document Revision 100102 Enabling Verify After From the main operating screen depicted below SELECT COPY OR COMPARE Press the 2 key and the screen will now display in sequence SELECT OPTI ONS lt m DI mn lt gt 1 m JJ O O U lt 1 MULTI PLE I MAGES SELECT OPTIONS Press the 0 key and the screen will now read VERIFY AFTER COPY YES NO Press the START YES key to enable or the STOP NO key to disable the Verify After option If you press the START YES key the screen will read VERIFY AFTER COPY IS ON You will then be returned to the main operating screen SELECT COPY OR COMPARE Page 25 CD 3000 Series Operator s Guide Document Revision 100102 Copying From A Hard Disk Image After a hard disk image has been created it can be used as the copying master source If you have not already created a hard disk image do so now as described in the previous section Multiple Images Disabled To make copies from a hard disk image that was previously created with the Multiple Images feature disabled i e from a single hard disk image the steps are as follows e From the main operating screen depicted below 0 m Fa m O O O U lt O J O O U
25. sion of firmware will be available for downloading to your computer from the MediaFORM web site www mediaform com Once a firmware image file is downloaded a Firmware Update CD can then be written using a computer a CD R RW recorder and most popular premastering programs such as Adaptec Easy CD Creator and Toast CeQuadrat WinOnCD Ahead Nero NTI CD Maker and others Refer to your premastering software documentation for details on how to record a disc from an image file After having created a Firmware Update CD perform the following steps to update the CD 3000 s firmware e From the main operating screen depicted below SELECT COPY OR COMPARE Load the Firmware Upgrade CD into the top CD R RW recorder Turn off the power to the 3000 Series Turn on the power to the 3000 Series The system will startup MF INC DUPLI CATION MADE EASY e You will see the initializing system screen y INITIALIZING SYSTEM e You will see the upgrade firmware screen UPGRADE FIRMWARE STOP NO START YES e Press the Start Yes key to upgrade the firmware UPGRADING FI RMWARE e Upon completion the system will automatically reboot e Remove the CD at this time e You will then see the following screens FI RMWARE UPGRADE PLEASE WAIT Page 35 CD 3000 Series Operator s Guide Document Revision 100102 FIRMWARE UPGRADE OK e You will then be returned to the main operating screen S
26. tensieviaissavieisrievtaissevdestssebda dsserdene 27 COMPARING FROM A HARD DISK IMAGE ccccccccccccnncnnncnononononnnonononnnonnnnnnnnnnnnonnnnnnnnnnnnnnnonnnnnnnnnononenonononanenenenecinecenases 29 Multiple Images Disabled rrrrnvrnvonnnrrnvvrvnrvnvrnennvnvrnensenvenensrneenenseneenensrnernensrneenenssnesrenssnessenssnessenssnessenssnesrene 29 Multipl Im ges Enabled A E 30 VIEWING SCSI DEVICE INFORMATION cccccccccccccccsccccccceceusuevsusususcsesescsusesesusceusesueueuscsesescececsvesecsussessssssssessssssseseess 32 WORKING WITH CD REWRITABLE CD RW DISCS rronnrvrrernnvnrrsrnnvnrrnnrrvrrennvsrrssnnvsrsnarsrsrennrsrssrnnnnrssersesrsnnrsssssnnnnn 33 CD RW Supported Formats siniese add it aent 33 CD RW Copying Speed murhus eee vine EEEE R EENES 33 SETTING THE INTERNAL CLOCK sseeeesseosesecssooeesseseseecescsecscoeesscooeeseesesoeosseoeesecesesecessoessooeesseceseseescoeeessooessseesese 34 FIRMWARE UPDATES acond 35 SYSTEN TRITT 37 APPENDIX A SUPPORTED FORMA TS cisssssccscesscssscesssseenossssusecoecassessscdasessectesoscectessusasessectesossestesessesscsessessecsese 38 CD 3000 Series Operator s Guide Document Revision 100102 About MediaFOR M Inc Thank you for purchasing MediaFORM s CD 3000 standalone autoloading CD duplicator MediaFORM manufactures a wide variety of CD duplication equipment This includes manual and fully automatic CD and DVD duplicators and printers We hope you will consider us for all of
27. the following will be displayed on the screen 1 1 GENERIC CRD BP17 1 55 RID 0000000000 lt The device information is displayed for each of the CD R RW recorders installed in the CD 3000 This includes their host number model name and firmware version Page 32 CD 3000 Series Operator s Guide Document Revision 100102 Working With CD ReWritable CD RW Discs In addition to working with CD Recordable CD R discs the CD 3000 can also copy both to and from CD ReWritable CD RW discs CD R discs are write once and can be read on any CD audio player CD ROM and MultiRead CD ROM drive CD RW discs can be rewritten to as many as 1 000 times and are read using MultiRead CD ROM usually 24x and faster and CD ROM drives CD RW Supported Formats The CD 3000 can copy CD RW discs written in most logical formats ISO 9660 audio etc but not those created using the Universal Disk Format UDF CD RW discs using UDF are produced by packet writing software such as Adaptec DirectCD CeQuadrat PacketCD Prassi abCD etc Because UDF discs cannot be read by all CD ROM drives they are not a good choice for distributing data CD RW Copying Speed CD RW copying speed is determined by two factors the CD RW writing speed of the recorders installed in the CD 3000 8x with Pioneer A03 drives and the maximum speed rating of the discs themselves CD RW discs are manufactured with an internal speed code which is checked be
28. w which is located on the back of the CD 3000 Once the proper voltage setting has been confirmed it is time to turn on the unit The power switch is located at the back of the unit next to the AC power input Wait a minute or two while the system starts up The screen will now read MF INC DUPLI CATI ON MADE EASY After the startup routine is complete a series of self diagnostics will be performed The screen will now read in sequence INITIALIZING SYSTEM Once complete the unit will display the main operating screen SELECT COPY OR COMPARE Page 13 CD 3000 Series Operator s Guide Document Revision 100102 Loading A Disc e After the CD 3000 s power has been switched on press the eject button on the front of the recorder to open its disc tray e Load by carefully placing the disc label side up into the recessed area of the disc tray so that the disc lays flat e Press the eject button on the front of the recorder to close the disc tray Removing A Disc e While the CD 3000 s power is still switched on press the eject button on the front of the recorder to open the disc tray e After the disc tray has completely opened lift the disc by its edges and carefully remove it e Press the eject button on the front of the recorder to close the disc tray Page 14 CD 3000 Series Operator s Guide Document Revision 100102 General Operation In addition to Relay Mode copying the 3000
29. will now read JJ O I U Press the START YES key The screen will now read IMAGE A 1 B 2 C 3 SELECT I MAGE Along the top line of the display will scroll the available images identified by their number 1 2 3 and 4 The CD 3000 defaults to the first image 1 For the purposes of this example press the 1 key to select this image followed by the START YES key The screen will now read ENTER QUANTI TY O O U lt z Q GOOD 0 BAD 0 OF 0 Progress will be displayed on the screen during the operation COPY OK PRESS START GOOD 0 BAD 0 OF 0 Page 27 CD 3000 Series Operator s Guide Document Revision 100102 e Press the START YES key and you will be returned to the main operating screen SELECT COPY OR COMPARE Note If discs failed to copy properly they will be dropped in the reject area in front of the drive bay These discs should not be used To help you determine the nature of the problem error messages can be displayed by pressing the 9 key on the keypad Page 28 CD 3000 Series Operator s Guide Document Revision 100102 Comparing From A Hard Disk Image For quality control purposes the CD 3000 is equipped with powerful verification capabilities Copied discs can also be compared against hard disk images This feature ensures copying integrity Note Due to the nature of the various compact disc formats only CD ROM Mode 1 CD ROM Mo
30. your duplication needs What To Expect From Your MediaFORM CD Duplicator Your MediaFORM CD 3000 CD duplicator is professionally designed and manufactured to give you years of trouble free operation To avoid accidental damage to your new CD duplicator please read and understand this manual thoroughly before operating the unit About This Manual This manual is written for both novice and experienced users Please read through this Operator s Guide from beginning to end before using the unit Once having read the manual follow along chapter by chapter This will provide the necessary understanding of your new CD 3000 CD duplicator Page 4 CD 3000 Series Operator s Guide Document Revision 100102 Getting Started Carefully remove the CD 3000 CD duplicator from the shipping container Inspect the contents and verify them against the packing slip Report any errors in shipping as soon as possible What s In The Box Your new CD 3000 CD duplicator includes CD 3000 CD duplicator Power cord Firmware CD Manual CD MediaFORM Product amp Warranty Registration card Packing Materials Please retain the original box and packaging in the event that the unit requires future servicing This will help to reduce the possibility of damage occurring in transit Page 5 CD 3000 Series Operator s Guide Document Revision 100102 The Best Place To Put The CD 3000 The best operating location for the CD 3000 CD dupl
Download Pdf Manuals
Related Search