GE Profile SCA2000F Oven
Contents
1. PREPARING THE REAR WALL Attach the exhaust adaptor to the rear mounting plate by sliding it into the guides at the top center of the FOR OUTSIDE BACK EXHAUST plate on the wall side Place the mounting plate against the rear wall and Damper Exhaust Adaptor align it with the holes drilled earlier hinge side up Using a pencil put dots through slots F and G and Je Mounting Plate through holes H and I Remove the mounting plate Slide Exhaust wall side and draw lines extending through the points This will aa Into give the Icoation and size of the box cutout for the pre Rear Panel rear wall duct Push in securely until it is past the top locking tabs and in the lower locking tabs Take care to assure the damper hinge is installed so that it is at the top and that the damper swings freely 4 Carefully guide the exhaust adaptor now attached to the mounting plate into the house duct before using the screws to attach the plate to the wall 15 Installation Instructions ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts At least one wood screw must be used to attach the plate to a wall stud Remove the toggle wings from the bolts Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 3 4 onto each bolt To use toggle bolts Spacing for Toggles More2. Secure the power cord to the cabinet wall as desired to keep excess length out of the way using the power cord strap and the black metal screw Installation Instructions RECIRCULATING non vented Ductless INSTALLATION OVERVIEW Attach Mounting Plate to Wall Prepare Top Cabinet Adjust Blower Mount the Oven Install Charcoal Filter ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts At least one wood screw must be used to attach the plate to a wall stud 1 Remove the toggle wings from the bolts Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 3 4 onto each bolt To use toggle bolts Spacing for Toggles More ji Than Wall Thickness Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate NOTE Before tightening toggle bolts and wood screw make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet CAUTION Be careful to avoid pinching fingers between the back of the mounting plate and the wall 4 Tighten all bolts Pull the plate away from the wall to help tighten the bolts USE TOP CABINET TEMPLATE FOR PRE
3. j Than Wall Thickness W lt Bolt End Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate NOTE Before tightening toggle bolts and wood screw make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet CAUTION Be careful to avoid pinching fingers between the back of the mounting plate and the wall 4 Tighten all bolts Pull the plate away from the wall to help tighten the bolts USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through Read the instructions on the TOP CABINET TEMPLATE Tape it underneath the top cabinet e Drill the holes following the instructions on the TOP CABINET TEMPLATE CAUTION Wear safety goggles when drilling holes in the cabinet bottom ADAPTING BLOWER FOR OUTSIDE BACK EXHAUST Remove the 3 screws that hold the blower plate to the oven Slide blower plate from under its retaining flange Remove and save the screw that holds blower motor to oven Carefully pull out the blower unit The wires will extend far enough to allow you to adjust the blower unit BEFORE Fan Blade Openings Facing Up Installation Instructions Gen
4. hole for toggle bolts NOTE DO NOT MOUNT THE PLATE AT THIS TIME Installation Instructions 2 INSTALLATION TYPES choose A B or This oven is designed for adaptation to the following NOTE This oven is shipped assembled for Outside Top 3 types of ventilation Exhaust Select the type of ventilation required for your A Outside Top Exhaust Vertical Duct installation and proceed to that section B Outside Back Exhaust Horizontal Duct C Recirculating Non Vented Ductless OUTSIDE TOP EXHAUST OUTSIDE BACK EXHAUST VERTICAL DUCT HORIZONTAL DUCT Adaptor in Place for Outside Top Exhaust See page 12 See page 15 RECIRCULATING NON VENTED DUCTLESS A Charcoal Filter Accessory Kit is required for the non vented exhaust See your Owner s Manual for the kit number See page 19 11 Installation Instructions A OUTSIDE TOP EXHAUST vertical Duct INSTALLATION OVERVIEW Al Attach Mounting Plate to Wall A2 Prepare Top Cabinet A3 Install Adaptor A4 Mount the Oven A5 Adjust Exhaust Adaptor A6 Connect Ductwork ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts At least one wood screw must be used to attach the plate to a wall stud 1 Remove the toggle wings from the bolts 2
5. Adaptor Blower Plate Back of Oven Ifyou have a flat bottom cabinet the exhaust adaptor will be installed later through the cutout in the cabinet bottom q Place the oven in its upright position with the top of the unit facing up Attach the exhaust adaptor hinge side toward the back of the oven to the blower plate with the 2 bronze metal screws provided Make sure that the damper pivots easily before mounting oven You will need to make adjustments to assure proper alignment with your house exhaust duct after the oven is installed MOUNT THE OVEN FOR EASIER INSTALLATION AND PERSONAL SAFETY WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN IMPORTANT Do not grip or use handle during installation NOTE If your cabinet is metal use the nylon grommet around the power cord hole to prevent cutting of the cord NOTE We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf IMPORTANT If filler blocks are not used case damage may occur from over tightening screws NOTE When mounting the oven thread power cord through hole in bottom of top cabinet Keep it tight throughout Steps 1 3 Do not pinch cord or lift oven by pulling cord ree Lift oven tilt it forward and hook slots at back bottom edge onto 2 lower tabs of mounting plate Rotate front of oven up against cabinet bottom Insert a self aligning screw thr
6. Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings to 3 4 onto each bolt 12 To use toggle bolts Spacing for Toggles More ia Than Wall Thickness Mounting gt Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate NOTE Before tightening toggle bolts and wood screw make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is properly centered under the cabinet CAUTION Be careful to avoid pinching fingers between the back of the mounting plate and the wall 4 Tighten all bolts Pull the plate away from the wall to help tighten the bolts Installation Instructions USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws a hole large enough for the power cord to fit through and a cutout large enough for the exhaust adaptor Read the instructions on the TOP CABINET TEMPLATE o Tape it underneath the top cabinet e Drill the holes following the instructions on the TOP CABINET TEMPLATE CAUTION Wear safety goggles when drilling holes in the cabinet bottom ASSEMBLE AND INSTALL ADAPTOR a Damper ra Exhaust
7. Installation Instructions HOOD EXHAUST NOTE Read these next two pages only if you plan to vent your exhaust to the outside If you plan to recirculate the air back into the room proceed to page 6 OUTSIDE TOP EXHAUST EXAMPLE ONLY The following chart describes an example of one possible ductwork installation EQUIVALENT NUMBER DUCT PIECES LENGTH USED we Roof Cap 12 Ft Straight Duct 6 Round Rectangular to Round Transition Adaptor Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood Total Length IMPORTANT If a rectangular to round transition adaptor is used the bottom corners of the damper will have to be cut to fit using the tin snips in order to allow free movement of the damper OUTSIDE BACK EXHAUST EXAMPLE ONLY The following chart describes an example of one possible ductwork installation EQUIVALENT NUMBER DUCT PIECES LENGTH USED 3 Ft Straight Duct 3 x 10 Rectangular 90 Elbow Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood NOTE For back exhaust care should be taken to align exhaust with space between studs or wall should be prepared at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust Installation Instructions NOTE If you need to install ducts note that
8. When calculating the total duct length add the equivalent lengths of all transitions and adaptors plus the length of all straight duct sections The chart below shows you how to calculate total equivalent ductwork length using the approximate feet of equivalent length of some typical ducts NUMBER USED EQUIVALENT LENGTH Ft Ft Ft Total Ductwork Equivalent lengths of duct pieces are based on actual tests and reflect requirements for good venting performance with any vent hood Installation Instructions DAMAGE SHIPMENT INSTALLATION If the unit is damaged in shipment return the unit to the store in which it was bought for repair or replacement e If the unit is damaged by the customer repair or replacement is the responsibility of the customer e If the unit is damaged by the installer if other than the customer repair or replacement must be made by arrangement between customer and installer PARTS INCLUDED HARDWARE PACKET 4 Self aligning Machine 3 Screws 1 4 28 x 34 Nylon Grommet 2 for metal cabinets Metal Screws 1 black 1 8 5 1 2 Power Cord Strap 1 CN plastic i CS You will find the installation hardware contained in a packet with the unit Check to make sure you have all these parts Wood Screws 1 4 X 2 N Toggle Bolts and Qp Summ wing nuts 1 4 x 3 EER Exhaust Adaptor NOTE Some extra parts are included PARTS INCLUDED ADDITIONA
9. ones provided with this product The screws provided with this product hardware item 3 are self aligning large head machine screws 1 4 diameter 34 long with SAE 28 threads per inch It is important that you use replacement screws just long enough to attach the product to the cabinet The length can be determined by measuring the height of the overhang from the top of the cabinet floor to the bottom of the overhang and adding 1 to that length This will be the length of the 1 4 SAE 28 threads per inch screws you need You will also need to use washers 3 4 diameter to fit the screws you purchase This will prevent the screw heads from pulling through the bottom of the cabinet when tightening during installation Instructions 18 8 Install grease filters Cabinet Front Cabinet Bottom Shelf j A Filler Block Equivalent to Depth of Cabinet Recess ummu Mii Self Aligning Screw Oven Top Attach the oven to the top cabinet Insert 2 self aligning screws through outer top cabinet holes Turn two full turns on each screw Tighten center screw completely Tighten the outer 2 screws to the top of the oven While tightening screws hold the oven in place against the wall and the top cabinet See the Owner s Manual packed with the oven AEE Remove the tape from the ay cooktop lamp covers on the bottom of the oven
10. selfaligning screws through outer top cabinet holes Turn two full turns on each screw Install the charcoal filter When properly installed the wire mesh of the filter should be visible from the front Replace the grille and the 2 screws 6 Close the door L L Tighten center screw completely Tighten the outer 2 screws to the top of the oven While tightening screws hold the oven in place against the wall and the top cabinet Install grease filters Insert mesh side down See the Owner s Manual packed with the oven Remove the tape from the cooktop lamp covers on the bottom of the oven Secure the power cord to the cabinet wall as desired to keep excess length out of the way using the power cord strap and the black metal screw 22 Installation Instructions BEFORE YOU USE YOUR OVEN Make sure the oven has been installed according to Read the Owner s Manual instructions 2 Remove all packing material from the oven KEEP INSTALLATION INSTRUCTIONS FOR THE LOCAL INSPECTOR S USE 3 Install oven rack turntable in cavity Replace house fuse or turn breaker back on ALLATION ONS 5 Plug power co
11. smooth flat cabinets be careful to follow the instructions on the top cabinet template for power cord clearance e For best installation results we recommend a maximum cabinet depth of 12 Installation Instructions 1 PLACEMENT OF THE MOUNTING PLATE A REMOVING THE OVEN FROM B FINDING THE WALL STUDS THE CARTON REMOVING THE MOUNTING PLATE Remove the box containing the installation instructions filters exhaust adaptor and the small hardware bag Stand the oven on its control panel side Use a portion of the carton or some other material to protect the outer case from being damaged 1 Find the studs using one of the following methods A Stud finder a magnetic device which locates nails OR B Use a hammer to tap lightly across the mounting surface to find a solid sound This will indicate a stud location After locating the stud s find the center by probing the wall with a small nail to find the edges of the stud Then place a mark halfway between the edges The Control Panel Side center of any adjacent studs should be 16 or 24 from this mark The mounting plate is attached to the back of the oven Remove the 2 screws holding it to the oven 3 The plate will be used as the rear wall template and for mounting the oven to the wall THE OVEN MUST BE CONNECTED TO AT LEAST ONE WALL STUD
12. the total duct length of 34 x 10 rectangular or 6 diameter round duct should not exceed 140 equivalent feet Outside ventilation requires a HOOD EXHAUST DUCT Read the following carefully NOTE It is important that venting be installed using the most direct route and with as few elbows as possible This ensures clear venting of exhaust and helps prevent blockages Also make sure dampers swing freely and nothing is blocking the ducts Exhaust connection The hood exhaust has been designed to mate with a standard 3 x 10 rectangular duct Ifa round duct is required a rectangular to round transition adaptor must be used Do not use less than a 6 diameter duct DUCT PIECES Rectangular to Round Transition Adaptor Wall Cap 90 Elbow 90 Elbow 45 Elbow Roof Cap Straight Duct 6 Round or 31 4 x 10 Rectangular lt a of the damper EQUIVALENT LENGTH IMPORTANT If a rectangular to round transition adaptor is used the bottom corners of the damper will have to be cut to fit using the tin snips in order to allow free movement Maximum duct length For satisfactory air movement the total duct length of 3 x 10 rectangular or 6 diameter round duct should not exceed 140 equivalent feet Elbows transitions wall and roof caps etc present additional resistance to airflow and are equivalent to a section of straight duct which is longer than their actual physical size
13. with the screws Retaining g Flange l g x Blower Plate I i Oe f J Ja ee eg lt e Blower Motor Screw ae ack of Oven FOR EASIER INSTALLATION AND PERSONAL SAFETY WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN IMPORTANT Do not grip or use handle during installation NOTE If your cabinet is metal use the nylon grommet around the power cord hole to prevent cutting of the cord NOTE We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf IMPORTANT If filler blocks are not used case damage may occur from over tightening screws Installation MOUNT THE OVEN cont NOTE When mounting the oven thread power cord through hole in bottom of top cabinet Keep it tight throughout Steps 1 3 Do not pinch cord or lift oven by pulling cord cas Lift oven tilt it forward and hook slots at back bottom edge onto 2 lower tabs of mounting plate Rotate front of oven up against cabinet bottom Insert a selfaligning screw through top center cabinet hole Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged It will be completely tightened later Be sure to keep power cord tight Be careful not to pinch the cord especially when mounting flush to bottom of cabinet If your cabinet front hangs more than 2 below the cabinet bottom you may need to use longer screws than the
14. Draw a line down the center of the studs Set the oven upright Remove and properly discard plastic bags and Styrofoam Remove any adhesive tape if there is any on the exhaust adaptor the grease filters and the power supply cord Open the oven door and remove any accessories from inside the oven Installation Instructions DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position beneath flat bottom Plate position beneath framed recessed cabinet cabinet bottom Mounting Plate Tabs Mounting Plate Tabs Touching the Cabinet Touching the Back Bottom Frame 30 to Cooktop At least 30 up to 36 Plate position beneath recessed bottom cabinet with front overhang Your cabinets may have decorative trim that interferes with the oven installation Remove the decorative trim to install the oven properly and to make it level Mounting Plate with Tabs Below Cabinet THE OVEN MUST BE LEVEL Use a level to make Bottom the Same sure the cabinet bottom is level Distance as the Front Overhang Depth If the cabinets have a front overhang only with no back or side frame install the mounting plate down the same distance as the front overhang depth This will keep the oven level L Measure the inside depth of the front overhang Draw a horizontal line on the back wall an equal distance below the cabinet bottom as the inside depth of the front overhang For t
15. Installation Speedcook Oven Instructions Questions Call 800 GE CARES 800 432 2737 or Visit our Website at Www GEAppliances com BEFORE YOU BEGIN Read these instructions completely and carefully e Note to Consumer Keep these instructions for future reference bg IMPORTANT Save these instructions for local i r Skill level Installation of this appliance requires basic Bere se ate beea nee mechanical and electrical skills IMPORTANT Observe all governing e Proper installation is the responsibility of the installer codes and ordinances ee e Product failure due to improper installation is not e Note to Installer Be sure to leave these instructions covered under the Warranty with the Consumer READ CAREFULLY KEEP THESE INSTRUCTIONS Installation Instructions CONTENTS C Recirculating Attach Mounting Plate to Wall General information Important Safety Instructions Preparation of Top Cabinet Adapting Blower for Electrical Requirements q Recirculation Hood Exhaust Damage Shipment Installation Parts Included Tools You Will Need Mount the Oven Installing the Charcoal Filter Before You Use Your Oven Mounting Space Step by step installation guide Placement of Mounting Plate Removing the Mounting Plate Finding the Wall Studs Determining Wall Plate Location Aligning the Wall Plate Installation Types A Outside Top Exhaust Attach Mounting Pla
16. L PARTS Top Cabinet TOP CABINET TEMPLATE Template INSTALLATION Installation 1 INSTRUCTIONS Instructions Separately Packed Grease Filters Installation Instructions TOOLS YOU WILL NEED p A Ruler or tape measure idwilaiatlatdataltalilalalaallan 9 and straight edge 1 and 2 Phillips screwdriver a Carpenter square optional f2 Oc G Tin snips for cutting damper if required Scissors ito cut template if necessary Electric drill with 3 167 7 16 1 2 and 5 8 drill bits Filler blocks or scrap wood pieces if needed for top cabinet spacing used on recessed bottom Qy 7 f cabinet installations only Gloves ES nN Saw saber hole or keyhole Stud finder or Hammer optional Duct and masking tape NOTES Bottom edge of nos cabinet necd to e The space between the cabinets must be 30 wide be 30 or more and free of obstructions from the cooking surface If the space between the cabinets is greater than 30 a Filler Panel Kit may be used to fill in the gap between the oven and the cabinets Your Owner s Manual contains the kit number for your model e This oven is for installation over ranges up to 36 wide 66 or more W If you are going to vent your oven to the outside from the floor 3 see Hood Exhaust Section for exhaust duct to the top j preparation of the oven When installing the oven beneath
17. PARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through Read the instructions on the TOP CABINET TEMPLATE Tape it underneath the top cabinet e Drill the holes following the instructions on the TOP CABINET TEMPLATE CAUTION Wear safety goggles when drilling holes in the cabinet bottom Installation Instructions C3 ADAPTING BLOWER FOR ns oe oe en Poi openings RECIRCULATION See en ney BEFORE Fan Blade Openings Facing Up NOTE The exhaust adaptor with damper is not needed for recirculating models You may want to save them for possible future use 1 Remove and save screws that hold the blower plate to the oven a F lt Blower Plate Screws Retaining Flange l I Blower Plate I T Slide the blower plate from under its retaining flange and lift it off Remove and save screw that holds the blower motor to oven iein ae AFTER Fan Blade etaining Flange Openings Facing Forward Blower Plate 35 Cm e ge Blower Motor Screw Carefully pull out the blower unit The wires will extend far enough to allow you to adjust the blower unit NOTE Make sure wires remain routed in the grooves of the motor frame 5 Place the blower unit back into the opening CAUTION Do not pull or stretch the blower unit wiring Make sure the wires are no
18. d especially when mounting flush to bottom of cabinet If your cabinet front hangs more than 2 below the cabinet bottom you may need to use longer screws than the ones provided with this product The screws provided with this product hardware item 3 are self aligning large head machine screws 1 4 diameter 3 long with SAE 28 threads per inch It is important that you use replacement screws just long enough to attach the product to the cabinet The length can be determined by measuring the height of the overhang from the top of the cabinet floor to the bottom of the overhang and adding 1 to that length This will be the length of the 1 4 SAE 28 threads per inch screws you need You will also need to use washers 3 4 diameter to fit the screws you purchase This will prevent the screw heads from pulling through the bottom of the cabinet when tightening during installation Installation Instructions MOUNT THE OVEN cont INSTALLING THE CHARCOAL Cabinet Front FILTER Cabinet Bottom Shelf Remove 2 screws on top of grille using a Phillips Filler Block screwdriver You may need to open the cabinet doors to remove the screws Equivalent 2 Open the door to Depth of Cabinet 3 Remove the grille Recess Screws J lt Self Aligning Screw L sm Oven Top Attach the oven to the top cabinet Insert 2
19. his type of installation with front overhang gt only align the mounting tabs with this horizontal J line not touching the cabinet bottom as described in Step D 30 to Cooktop Y Installation Instructions D ALIGNING THE WALL PLATE Draw a Vertical Line on Wall from Center of Top Cabinet CAUTION Wear gloves to avoid cutting fingers on sharp edges 1 Draw a vertical line on the wall at the center of the 30 wide space Use the mounting plate as the template for the rear wall Place the mounting plate on the wall making sure that the tabs are touching the bottom of the cabinet or the level line drawn in Step C for cabinets with front overhang Line up the notch and center line on the mounting plate to the center line on the wall While holding the mounting plate with one hand draw circles on the wall at holes A B C and D see illustration above actual plate marked with arrows Four holes must be used for mounting 10 NOTE Holes C and D are inside area E If neither C nor D is in a stud find a stud somewhere in area E and draw a fifth circle to line up with the stud It is important to use at least one wood screw mounted firmly in a stud to support the weight of the oven Set the mounting plate aside Drill holes on the circles If there is a stud drill a 346 hole for wood screws For holes that don t line up with a stud drill a
20. ough top center cabinet hole Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged It will be completely tightened later Be sure to keep power cord tight Be careful not to pinch the cord especially when mounting flush to bottom of cabinet Installation Instructions MOUNT THE OVEN cont If your cabinet front hangs more than 2 below the cabinet bottom you may need to use longer screws than the ones provided with this product The screws provided with this product hardware item 3 are self aligning large head machine screws 1 4 diameter 34 long with SAE 28 threads per inch It is important that you use replacement screws just long enough to attach the product to the cabinet The length can be determined by measuring the height of the overhang from the top of the cabinet floor to the bottom of the overhang and adding 1 to that length This will be the length of the 1 4 SAE 28 threads per inch screws you need You will also need to use washers 3 4 diameter to fit the screws you purchase This will prevent the screw heads from pulling through the bottom of the cabinet when tightening during installation Cabinet Front SJ Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess Self Aligning Screw Oven Top 4 Attach the oven to the top cabinet Insert 2 selfaligning screws through outer top cabinet hole
21. rd into a dedicated NEMA 14 30R wall receptacle NEMA 14 30R Wall Receptacle Insure proper ground exists before use 23 164D3370P269 49 40339 1 3828W5U0315 07 03 JR Printed in Korea
22. rsonal safety it is recommended that two people install this product IMPORTANT PLEASE READ CAREFULLY FOR PERSONAL SAFETY THIS APPLIANCE MUST BE PROPERLY GROUNDED TO AVOID SEVERE OR FATAL SHOCK NEMA 14 30R The wall outlet receptacle Wall Receptacle recommended for this appliance is NEMA 14 30R and accepts the 4 prong grounded plug of this appliance Insure proper ground exists before use You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded Where a standard 3 prong wall receptacle is encountered it is very important to have it replaced with a properly grounded NEMA 14 30R wall receptacle installed by a qualified electrician DO NOT UNDER ANY CIRCUMSTANCES CUT DEFORM OR REMOVE ANY OF THE PRONGS FROM THE POWER CORD DO NOT USE WITH AN EXTENSION CORD ELECTRICAL REQUIREMENTS Product rating is 240 208 volts AC 60 Hertz 30 amps and 6 5 kilowatts This product must be connected to an individual properly grounded branch circuit protected by circuit breakers or time delay fuses Wire size must conform to the requirements of the National Electrical Code or the prevailing local code for this kilowatt rating The outlet box should be located in the cabinet above the oven The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical Code or the prevailing local code
23. s Turn two full turns on each screw 6 Tighten center screw completely Tighten the outer 2 screws to the top of the oven While tightening screws hold the oven in place against the wall and the top cabinet 14 Install grease filters See the Owner s Manual packed with the oven Remove the tape from the cooktop lamp covers on the bottom of the oven Secure the power cord to the cabinet wall as desired to keep excess length out of the way using the power cord strap and the black metal screw ADJUST THE EXHAUST ADAPTOR Open the top cabinet and adjust the exhaust adaptor to connect to the house duct For top exhaust on the flat bottomed cabinets open the top cabinet and attach the exhaust adaptor to the oven through the cabinet bottom with the 2 bronze metal screws provided Damper amp f Back of Oven CONNECTING DUCTWORK House Duct Extend the house duct down to connect to the exhaust adaptor 2 Seal exhaust duct joints using duct tape Installation Instructions OUTSIDE BACK EXHAUST Horizontal Duct INSTALLATION OVERVIEW Prepare Rear Wall Attach Mounting Plate to Wall Prepare Top Cabinet Adjust Blower Mount the Oven
24. t pinched 20 Installation Instructions Secure blower unit to oven with the screw removed in Step 2 Replace blower plate with the screws removed in Step 1 o qe Blower Plate Screws Retaining Blower Plate l l I h P a ack of Oven al J ea S i gt lt Blower Motor Screw FOR EASIER INSTALLATION AND PERSONAL SAFETY WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN IMPORTANT Do not grip or use handle during installation NOTE If your cabinet is metal use the nylon grommet around the power cord hole to prevent cutting of the cord NOTE We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf IMPORTANT If filler blocks are not used case damage may occur from over tightening screws 21 NOTE When mounting the oven thread power cord through hole in bottom of top cabinet Keep it tight throughout Steps 1 3 Do not pinch cord or lift oven by pulling cord Ti Lift oven tilt it forward and hook slots at back bottom edge onto 2 lower tabs of mounting plate Rotate front of oven up against cabinet bottom Insert a self aligning screw through top center cabinet hole Temporarily secure the oven by turning the screw at least two full turns after the threads have engaged It will be completely tightened later Be sure to keep power cord tight Be careful not to pinch the cor
25. te to Wall Preparation of Top Cabinet Assemble and Install Adaptor Mount the Oven Adjust the Exhaust Adaptor Connecting Ductwork Outside Back Exhaust Preparing Rear Wall for Outside Back Exhaust Attach Mounting Plate to Wall Preparation of Top Cabinet Adapting Blower for Outside Back Exhaust Mount the Oven Installation Instructions IMPORTANT SAFETY INSTRUCTIONS This product requires a 4 prong grounded outlet The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded If not properly grounded or if the outlet box does not meet electrical requirements noted under ELECTRICAL REQUIREMENTS a qualified electrician should be employed to correct any deficiencies CAUTION For personal safety remove house fuse or open circuit breaker before beginning installation to avoid severe or fatal shock injury CAUTION For personal safety the mounting surface must be capable of supporting the cabinet load in addition to the added weight of this 70 85 pound product plus additional oven loads of up to 50 pounds or a total weight of 120 135 pounds CAUTION For personal safety this product cannot be installed in cabinet arrangements such as an island or a peninsula It must be mounted to BOTH a top cabinet AND a wall NOTE For easier installation and pe
26. tly remove the wires from the grooves Reroute the wires through grooves on other side of the blower unit Before Rerouting After Rerouting ires Routed Through Right Side Wires Routed Through Left Side Rotate blower unit counterclockwise 180 Before Rotation After Rotation Back of Oven Roll the blower unit 90 so that fan blade openings are facing out the back of the oven Before Rolling After Rolling Laser see z g Back of Oven Back of Oven Locate the 2 knockout plates on the rear oven panel near the top of the oven Using tin snips carefully cut the web area from the 2 holes side by side that secure the knockouts to the oven Cut all 4 webs on both rear knockouts this will allow the ventilation fan airflow to exhaust out the rear of the oven Oven Rear Panel Snip all 4 webs on each knockout panel and remove the metal knockouts for rear airflow CAUTION Be sure to trim the sharp edges from the openings after removing the knockout plates 17 Place the blower unit back into the opening AFTER Fan Blade Openings Facing Back CAUTION Do not pull or stretch the blower unit wiring Make sure the wires are not pinched NOTE The blower unit exhaust openings should match exhaust openings on rear of oven Secure the blower unit to the oven with the screw removed earlier Replace the blower plate in the same position as before
Download Pdf Manuals
Related Search