Pelonis WM-HO202C Oil Filled Radiator Heater
Contents
1. Maintenances For Heater amp Fan Heater Maintenances 1 Trouble Shooting Fails to operate Ensure that your circuit breaker or fuse is working properly Be sure the heater is plugged in and that the electrical outlet is working properly Check for any obstruction If you find any obstruction turn the heater OFF Unplug the heater and wait a few minutes for it to cool down Carefully remove the obstruction Plug the heater in and turn it on again Overheated Remove the obstruction or situation that caused the unit to overheat Turn the heater to the OFF setting and turn the thermostat to HI Unplug the heater and wait 5 to 10 minutes for the heater to cool down Plug the heater back in and resume operation 2 Major Malfunction Analysis In fact many heaters failure may attribute to the thermal fuse thermal cut off being melted thermal limiter blowing or to a power switch and thermostat problem To detect the specific problem that may cause the heater to work improperly you need to utilize an ammeter to measure it between the two joints in order to judge whether it is on or off For a specific problem please also refer to the following chart Diagnoses for the detailed problem and solution Maintenances For Heater amp Fan Symptom Possible Cause Elimination Thermostat been turned off Set it higher Thermal fuse cut off melted Replace it Thermal limiter blew Re2. fan is turned OFF and if it remains plugged into the outlet it will start at the same speed the next time it is turned on 2 Fan not oscillating To start and stop the oscillation of the fan push the Oscillation Button on the control panel Did this solve your problem 3 No power Not working Check to make sure the power cord is connected properly to the power outlet Make sure there is power from the A C outlet check the circuit breaker or fuse in your home 4 Fire Smokes Sparks Popping Make sure the unit is unplugged Contact Pelonis customer service 5 Adjusting Angle To adjust the vertical angle tilt fan head up or down 6 Adjusting Height Loosen the height adjustment knob and adjust fan to the desired height Re tighten the adjustment knob before turning fan on Maintenances For Heater amp Fan 2 Major Malfunction Analysis Malfunction Cause of Problem Solution No power to circuit Not turning Disconnection between circuit and power cord Check the switch socket down lead for any disconnection Thermal fuse burn Replace thermal fuse Faulty timer function Check the timer Faulty control panel Replace control panel Motor get stuck Check the motor bearing and knock the motor Humming noise Open circuit of capacitor Replace capacitor Open circuit of coil Replace stator assembly Do not oscillate Faulty oscillation c
3. fully in the outlet Replace the power cord code Readout display abnormal Sensor working improperly Replace sensor PC board problem Replace PC board Blow extremely hot air Sensor working improperly Replace sensor PC board problem Replace PC board Thermostat problem Replace thermostat heat The fan is running but do not The wire terminal loose Fasten it or replace wire Hard to repair Heating element problem Maintenances For Heater amp Fan Diagnoses for the oil filled heater Case Symptom Possible Cause Elimination Thermal limiter failure Power light Heating element failure stay on Loose wire Power cord Power switch failure Power light Do not Thermostat failure turned off Heat Thermal fuse failure Loose wire Caution light Thermal limiter failure stay on Loose wire Caution light Heating element failure turned off Loose wire f Dust built up First time use Smell Oil in your heater Burnt smell Wire burned out Metal friction Metal components Noisy From oil tank Oil react to the water The noise will taper off itself Maintenances For Heater amp Fan Fan Maintenances 1 Trouble Shooting 1 Fan Speed Adjust the speed of the fan by pressing the Speed Button Press the button successively to adjust between low medium and high speeds If the
4. nces For Heater amp Fan Try the oscillating function to make sure if your fan still oscillate Try each of the speed choice make sure if any of them works Test Blade operation by rotating it with your hand There should be no friction with the Plastic Nut If Blade does not rotate freely reassemble your fan then resume operation again
5. ontroller Check the controller Faulty super gear Replace gear box Oscillation arm broken or loose Replace oscillation arm or neck Faulty synchronous motor Replace synchronous motor Louver not turning Box fan Faulty synchronous motor switch Check the synchronous motor switch Faulty synchronous motor Replace synchronous motor Serious vibration Deformed fan blade Replace fan blade Loose spinner Replace spinner Motor malfunction Check the motor Serious abnormal noise Motor rotor deflection Replace motor rotor Curved rotor axes Trim the rotor shaft Loose bearing Replace bearing Bearing lack of lubricator Refill the lubricator Cannot turn on at lowest setting Inflexible rotor Coaxiality differ between the rotor and stator Misdistribution of air gap Check the rotor stator bearing replace the defective part Faulty speed controller Replace speed controller Motor overheat Coil short circuit Replace stator and rotor assembly Fan Problem basic Solution 1 Be sure the fan is plugged in and that the electrical outlet is working properly 2 Be sure the power indicator light is on 3 Check for any obstruction If you find any obstruction turn the fan OFF Unplug the fan and carefully remove the obstruction Plug the fan in and turn it on again 4 5 6 Maintena
6. place thermal limiter Thermostat or power switch failed to work properly Replace thermostat or switch Stopped heat with Power The wire terminal loose Fasten it or replace wire frequently after running for a short period light turned off The screw that pegs connecting wire Fasten it or replace wire on the isolator scorched or loose Internal connecting wire broken Replace wire Power cord broken Replace power cord PC board problem Replace PC board Lamp pilot light turn off Set it higher Adjustable thermostat set too low The wire terminal loose Fasten it or replace wire Lamp pilot light remains on but heater do not heat Heating element problem Hard to repair Working properly but lamp pilot turned off Pilot problem Replace pilot Connection wire terminal loose Fasten it or replace wire Control box or radiator assembly leaking oil Safety valve assembly or gasket heater washer or radiator assembly juncture leaking Replace the unit Making strange noise when startup Oil filled heater The inflation and deflation of radiator assembly or the radiator assembly mixed with a little steamed water Normal Normal Put on soft surface Construction of the heater with fan Making buzzing noise A lot of dust around the fan Clean it First use Normal Give bad smell Leaking oil Replace the unit Plug melted The plug does not fit
Download Pdf Manuals
Related Search