GE JSP47 Electric Kitchen Range
Contents
1. Effective January 1 1996 the National Electrical Code requires that new construction not existing utilize a 4 conductor connection to an electric range When installing an electric range in new construction follow Steps 3 and 5 for 4 wire connection You must use a 3 wire single phase A C 208Y 120 Volt or 240 120 Volt 60 hertz electrical system If the electrical service provided does not meet the above specifications have a licensed electrician install an approved outlet Use only a 3 conductor or a 4 conductor UL listed range cord These cords may be provided with ring terminals on wire and a strain relief device A range cord rated at 40 amps with 125 250 minimum volt range is required A50 amp range cord is not recommended but if used it should be marked for use with nominal 1 3 8 diameter connection openings Care should be taken to center the cable and strain relief within the knockout hole to keep the edge from damaging the cable Because range terminals are not accessible after range is in position flexible service conduit or cord must be used NOTE If conduit is being used go to Step 3D and then to Step 6 or 7 e On some models a filter capacitor may be connected between the black and white leads on the junction block ALL NEW CONSTRUCTIONS MOBILE HOMES AND INSTALLATIONS WHERE LOCAL CODES DO NOT ALLOW GROUNDING THROUGH NEUTRAL REQUIRE A 4 CONDUCTOR UL LISTED RANGE CORD Cont2. supplied with bracket Unless properly installed the range could be tipped by stepping or sitting on the door Injury may result from spilled hot liquids or from the range itself Leveling Leg Continued on following page Installation Instructions Installing The Range com 11 SLIDE RANGE INTO OPENING cont 11 SLIDE RANGE INTO OPENING A Position the range in front of the cabinet opening Make sure that the glass which overhangs the countertop clears the countertop If necessary raise the unit by lowering the leveling legs Push while lifting the range into the opening until the range is within 2 of engaging the anti tip bracket Remove the protective trim from the side of glass if provided Using the adjustable pliers or wrench carefully screw in the back leveling leg until the glass overhang comes to rest on the countertop Adjustable wrench or pliers Then carefully screw in the front two leveling legs similar to E until the glass overhang touches the countertop Carefully push the range into the opening until the countertop fully engages the control panel The back glass overhang should cover the cutout opening O Y Countertop Make sure the edge of the countertop fits flush against the end of the Front Control Panel Plug the range cord into the receptacle Locate the cord in the back of the range in a manner that it will not touch or be moved by the drawer
3. D setting to observe that the element glows within 15 seconds Turn the knob off when glow is detected If the glow is not detected within the time limit recheck the range wiring connections If change is required retest again If no change is required have building wiring checked for proper connections and voltage 14 Installation Instructions Alternate Construction OPTIONAL MAINTOP FILLER OR BACKGUARD KIT If counter opening extends to the wall it will require Maintop Filler Kit Supplied with the range or Backguard Kit JXS37XX or JXS32XX to close the gap NOTE If the countertop is greater than 257 it will show a gap between the backguard and wall or between filler kit and the wall If the countertop is less than 257 a gap will occur between the countertop front and the control panel ends see section 11G on page 12 If you are using the optional backguard kit refer to the backguard kit instructions for installation details Must Be Level Must Be Flat Smooth Cut Flat en Must Be 5 30 gt I Must Be Level gt 31 1 8 15 If you use the filler kit place the metal filler piece supplied with the range to the back of the range as shown in the figure below Start the 2 screws into the upper holes at the outside rear of the range above the louvers and through the slots in the trim holding the filler piece centered on the maintop frame and pushing upward to close the gap between
4. Installation Checklist con Door removal is not a requirement for Storage Drawer Removal installation of the product but is an added convenience To remove the door Y Pull the drawer out until it stops f it will go penhe cooras erario Y Lift the front of the drawer until the Push both hinge Hinge stops clear the guides Unlocked locks down toward Q Position the door frame Hinge N tothe unlocked Slot Ni position This may require a flat blade screwdriver Y Pull forward and remove the drawer Y Place hands on both sides of the door and close the oven door to the removal position This is half way between the broil stop and fully closed Y Lift door up and out until the hinge arms clear the slots Hinge Clears Slot NOTE The oven door is very heavy Be sure you have a firm grip before lifting the oven door off the hinges Use caution once the door is removed Do not lay the door on its handle This could cause dents or scratches Remove packing materials Remove labels on door plastic on trim and panel and all tape around the range Installation Instructions 11 Pre Installation Cutout and Required Clearances OVERALL DEPTH 27 1 2 If cabinets are placed less than 30 above the range see Alternate Construction section AF on page 16 30 ranges conform to U L requirements for 0 spacing from vertical walls below countertops Allow 1 4 minimum clearance at the ba
5. Position range cord so that there is no interference with storage drawer STORAGE DRAWER olf 7 N r I lt AW 12 FINAL CHECK OF THE ANTI TIP BRACKET When installation is complete and the range is in place check to be sure that the rear leveling leg is fully inserted into the slot of the Anti Tip Bracket Installation Instructions Installing The Range com REPLACING THE OVEN DOOR NOTE The oven door is heavy You may need help lifting the door high enough to slide it into the hinge slots Do not lift the door by the handle Lift the oven door by placing one hand on each side The door is heavy so you may need help Do not lift the door by the handle With the door at the same angle as the removal position halfway between the closed and broil stop position seat the notch of the hinge arm into the bottom edge of the hinge slot The notch of the hinge arm must be fully seated into the bottom of the slot Hinge Arm Bottom Edge of Slot Hinge Notch Open the oven door as far as it will open Push the hinge locks Hingein up against the front Locked Position frame of the oven cavity to the locked position Notch of Hinge Securely Fitted into Bottom of Hinge Slot Close the oven door REPLACING THE STORAGE DRAWER Place the drawer rail on the guides Push the drawer in until it stops Lift the front of the drawer and push i
6. RE COVER 10 INSTALLING THE BRACKET IN WOOD OR CONCRETE Replace the wire cover on the back of the INSTALLATION WOOD range by replacing the a CONSTRUCTIONS ENS temoved A Locate the centers of the 4 holes earlier identified in Fig 1 as Floor Wood and Wall i Drill a 1 8 pilot hole through the NOTE When reinstalling the wire pre marked areas Note the angle of cover make sure that wires do not the wall screw in Fig 2 become pinched between the wire Shack cover Be the housing Mount the Anti Tip bracket with the 4 screws provided To Front Edge FIG 2 of Countertop 25 9 LOCATING THE ANTI TIP BRACKET as A Decide whether the bracket will be Screw Must Enter Wood 11 installed on the right or left side of the or Metal MO range opening A Place the bracket as shown in Fig 1 2 a em ace 1 Wall Plate mes INSTALLATION CONCRETE CONSTRUCTIONS For concrete installation you will need Adjacent 2 Le Cm two 1 4 x 1 1 2 lag screws and two Cabinet 22 sleeve anchors RO Locate the center of the 4 holes identified in Fig 1 as Floor Concrete and Wall Drill the recommended size holes in each Install the sleeve anchors into the FLOOR CONCRETE predrilled concrete holes and install the lag and wall screws through the Anti Ti A WARNING akt Make sure the a are j Range must be secured by Anti Tip securely tightened bracket supplied See instructions to install
7. T OPENINGS APPROXIMATELY 30 3 8 If range is installed in cabinet opening approximately 30 3 87 the Vertical Side Trim Kit JXS86XX should be used to cover gaps between range sides and cabinet Refer to the kit instructions for installation details CABINETS OVER THE RANGE LESS THAN 30 If a 30 clearance between cooking surface and overhead combustible material or metal cabinets cannot be maintained protect the underside of the cabinets above the cooktop with not less than 1 4 insulating millboard covered with sheet metal not less than 0 0122 thick NOTES NOTES NOTES NOTES 20 Printed in the United States
8. ck wall above the countertop Wall coverings counters and cabinets around range must withstand heat up to 200 F generated by the range Follow instructions packaged with alternate lt 30 Min appliance 6 Min From Walls For Optimum in 30 Min Installation These from Surfaces Must Coking Be Flat amp Level gt of aac to bottom De if cabina ad el x 15 Min vertical ly S th distance from the P bottom of the adjacent overhead cabinets y Pe u f Max depth of cord plug and 35 7 8 38 recpt box from floor to 4 to prevent countertop interference as i 1 1 4 Min Countertop with drawer T Ay to top of drawer o 2172 lal Countertop Depth 25 gn A Acceptable 251 at Electrical Tx Outlet Area DE 9 a S4 un TAg MIN Shave Raised Edge Max To Clear 31 1 8 Wide Control Panel Installation Instructions Standard Installation 2 STANDARD INSTALLATION Flat 25 Area Typically R 9 16 Min Z 36 ER k 29 15 16 30 1116 gt gt Smooth Cut 23 3 16 If the construction of your cabinet cannot A Center the 30 wide opening over the provide a 1 4 flat area at the back of the adjacent cabinets and mark with a countertop opening consider changing the straight edge countertop to accommodate this dimension l See Alternate Construction section If the area a le ne is not flat excess tension may be a
9. e 15 section AA for Installation Instructions or Backguard Kit JXS37XX or JXS32XX See page 15 Counter height greater than 36 3 4 Lower Trim Slide In Kit JXS56XX One side is not enclosed by a cabinet Bodyside Kit JXS77XX Island Installation To provide an optimum installation the top surface of the countertop must be level and flat lie on the same plane around the 3 sides that are adjacent to range cooktop Proper adjustments to make the top flat should be made or gaps between the countertop and range cooktop may occur Forcing the cooktop to fit may cause excessive gaps and could break the glass and void the warranty To obtain Kits a Visit GE Web Site See page 1 b Call GE Answer Center See page 1 c Contact Dealer Y Y Move range indoors in front of cabinet opening Do not use hand trucks when moving the unpackaged range Cooktop glass may be broken Protect the kitchen floor Flatten and place a piece of the shipping carton in front of the installation location to protect the flooring Do not remove the protective channel from the sides of the glass cooktop if applicable until later in the installation Protective Channel Carefully tilt the range to access the range leveling legs Use an adjustable wrench to screw leveling legs out so that glass support flanges clear top of countertop Continued on following page Installation Instructions Y Pre
10. ge with the ground plate and the ground screw Remove the 3 lower terminal screws from the terminal block Remove the ground screw and ground plate and retain them Cut and discard the ground strap DO NOT DISCARD ANY SCREWS Insert the one ground screw into the power cord ground wire terminal ring through the ground plate and into the frame of the range Insert the 3 terminal screws removed earlier through each power cord terminal ring and into the lower terminals of the terminal block Be certain that the center wire white neutral is connected to the center lower position of the terminal block Tighten screws securely into the terminal block Ground strap O al terminal strap Terminal AE plate grounding to range Ground E Skip to Step 8 and proceed with the installation Installation Instructions Electrical Connections cont 6 3 WIRE CONDUIT INSTALLATION A Loosen the 3 lower terminal screws from the terminal block Insert the center 4 WIRE CONDUIT INSTALLATION A Loosen the three lower terminal screws from the terminal block Remove the Terminal block Wire tips bare wire white neutral tip through the bottom center terminal block opening On certain models the wire will need to be inserted through the ground strap opening and then into the bottom center block opening Insert the two side bare wire tips into the lower left and the lower right terminal block open
11. ings Tighten the screws until the wire is firmly secured 35 to 50 inch Ibs Do not over tighten the screws since it could damage the wires NOTE ALUMINUM WIRING Aluminum building wire may be used but it must be rated for the correct amperage and voltage to make connection Connect wires according to this Step 6 or Step 7 depending on number of wires er l H fl q f GeT _ Conduit Wire used location and enclosure of splices etc must conform to good wiring practices and local codes Skip to Step 8 and proceed with the installation Before Terminal Ground strap ground screw and ground plate and retain them Cut and discard the ground strap DO NOT DISCARD ANY SCREWS Insert the ground bare wire tip between the range frame and the ground plate removed earlier and secure it in place with the ground screw removed earlier Insert the bare wire white neutral tip through the bottom center of the terminal block opening Insert the two side bare wire tips into the lower left and the lower right terminal block openings Tighten the screws until the wire is firmly secured 35 to 50 inch Ibs Do not over tighten the screws since it could damage the wires e Ground strap gt ii Neutral terminal After Terminal block Wire tips Ground plate grounding to range Ground GROUND Proceed to Step 8 Installation Instructions Installing the Range REPLACE THE WI
12. inued on following page Installation Instructions Electrical Connections cont 3 POWER CORD AND STRAIN For power cord installations only see RELIEF INSTALLATION Remove the wire cover on the back of the range by removing 2 screws using a 1 4 nut driver Do not discard these screws Remove the knockout ring 1 3 8 located on bracket directly below the terminal block To remove the knockout use a pair of pliers to bend the knockout ring away from the bracket and twist until ring is removed Terminal block appearance may vary Knockout Knockout ring ring removed in bracket the next step if using conduit assemble the strain relief in the hole Insert the power cord through the strain relief and tighten Allow enough slack to easily attach the cord terminals to the terminal block If tabs are present at the end of the winged strain relief they can be removed for better fit NOTE Do not install the power cord without a strain relief The strain relief bracket should be installed before reinstalling the rear range wiring cover Terminal Strain relief o Power cord e Bracket D For conduit installations only purchase a squeeze connector matching the diameter of your conduit and assemble it in the hole Insert the conduit through the squeeze connector and tighten Allow enough slack to easily attach the wires to the terminal block NOTE Do not install the condui
13. j Self Cleaning Radiant Installation Electric Slide In Range Instructio ns JSP42 JSP47 JSP57 JS968 If you have questions call 1 800 GE CARES or visit our website at www GEAppliances com Before You Begin Note to Installer Be sure to leave these instructions with the consumer Read these instructions carefully and completely Note to Consumer Keep these IMPORTANT save these instructions for future reference instructions for local inspector s use Proper installation is the responsibility of the installer and product failure due IMPORTANT_ observe all to improper installation is NOT covered governing codes and ordinances under warranty e NOTE This appliance must be properly grounded PARTS INCLUDED TOOLS YOU WILL NEED 1 8 Drill Bit and Wrench or Pliers Electric or Hand Drill for 1 7 16 Nut ES Rear Filler 2 Screws Screws Anti Tip Bracket MATERIALS YOU MAY NEED Gu aig Tape Measure wR 3 p Tin Snips Lag Bolts Anchor Sleeves For Anti Tip Bracket Mounted on Concrete Floors Only Straight Edge or Square Squeeze Connector 4 Wire Cord OR 3 Wire Cord For Gonduit 4 long 4 long Installations Only Hand or Sabre Saw 31 10599 1 11 04 JR 1 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS For Your Safety AA WARNING For personal safety remove house fuse or open circuit breaker before beginning installation Failure to do so could result in serious injury or e
14. n until the stops clear the guides Lower the front of the drawer and push in until it closes SPECIAL INSTRUCTIONS IF YOU ARE HAVING PROBLEMS WHILE REPLACING THE STORAGE DRAWER If Drawer Won t Close Drawer front Drawer does panel tipped not close away from completely body side Power cord 4 Rear drawer may be obstructing support is resting Remove and replace making sure the power cord is not obstructing the drawer and or the rail is in the guide If Drawer Is Crooked Rear drawer support is on top of guide rail Drawer front panel on the high side tipped to one side Remove and replace making sure the rail is in the guide Installation Instructions Y Final Checklist Check to make sure the circuit breaker is closed Reset or the circuit fuses are replaced Be sure power is in service to the building Check to be sure that all packing materials and tape on metal panel if applicable under control knobs and drawer have been removed Operation Checklist Check to make sure the Clock display is energized If a series of horizontal red lines appear in the display disconnect power immediately Recheck the range wiring connections If change is made to connections retest again If no change is required have building wiring checked for proper connections and voltage It is recommended that the clock be changed if the red lines appear Push down and turn any one of the four surface knobs to ME
15. pplied to conhe 9 ene breakage and al A ee ieda i voiding the warranty e careful not to damage the adjacen cabinets while cutting the countertop Use a hand or saber saw to make straight smooth cuts D Remove countertop raised edge if incorporated See illustration on page 5 Installation Instructions Electrical Connections ELECTRICAL REQUIREMENTS A CAUTION For personal safety do not use an extension cord with this appliance Remove house fuse or open circuit breaker before beginning installation This appliance must be supplied with the proper voltage and frequency and connected to an individual properly grounded branch circuit protected by a circuit breaker or fuse having amperage as specified on the rating plate The rating plate is located above the storage drawer on the oven frame We recommend you have the electrical wiring and hookup of your range connected by a qualified electrician After installation have the electrician show you where your main range disconnect is located Check with your local utilities for electrical codes which apply in your area Failure to wire your oven according to governing codes could result in a hazardous condition If there are no local codes your range must be wired and fused to meet the requirements of the National Electrical Code ANSI NFPA No 70 Latest Edition You can get a copy by writing National Fire Protection Association Batterymarch Park Quincy MA 02269
16. t without a squeeze connector The squeeze connector should be installed before reinstalling the rear range wiring cover Terminal Squeeze connector Conduit Bracket Installation Instructions 3 WIRE POWER CORD INSTALLATION A WARNING The neutral or ground wire of the power cord must be connected to the neutral terminal located in the center of the terminal block The power leads must be connected to the lower left and the lower right terminals of the terminal block Remove the 3 lower terminal screws from the terminal block Insert the 3 terminal screws through each power cord terminal ring and into the lower terminals of the terminal block Be certain that the center wire white neutral is connected to the center lower position of the terminal block Tighten screws securely into the terminal block DO NOT remove the ground strap connection Terminal block appearance may vary Neutral terminal Ground Skip to Step 8 and proceed with the installation A A Before Terminal Ay pl or block MO After Electrical Connections cont 4 WIRE POWER CORD INSTALLATION WARNING The neutral wire of the supply circuit must be connected to the neutral terminal located in the lower center of the terminal block The power leads must be connected to the lower left and the lower right terminals of the terminal block The 4th grounding lead must be connected to the frame of the ran
17. the bottom of the glass and the filler trim When the trim is set in the proper position tighten the 2 mounting screws The top of the trim should be located below the top surface of the glass to prevent pots pans and skillets from damaging the painted parts Refer to the Standard Installation of the Range beginning on page 6 Cooktop Maintop Filler 2 8 Screws Continued on following page Installation Instructions Alternate Construction con COUNTERTOPS HIGHER THAN 36 1 2 If countertop height is between 36 1 2 and 38 a lower trim kit JXS56XX is recommended Refer to the kit instructions for installation details Flat amp Level With Back amp Opposite Side AC FOR NON BUILT IN INSTALLATION END OF CABINET LOCATION When installing the range at the end of a cabinet section which will expose the unfinished side of the range use Body Side Kit UXS77XX Refer to the kit instructions for installation details 16 ISLAND INSTALLATION Attach the Anti Tip bracket per instructions in section D making sure that the rear of the bracket is 25 from the front of the countertop Be aware that the screws provided are long and may penetrate through the back of the island cabinets In this event use shorter screws not provided or the screws provided should be used in the floor See Section D for Wood Concrete Floor Installation Do not use Backguard Kit JXS37XX or JXS32XX FOR CABINE
18. ven death N All rough in and spacing dimensions must be met for safe use of your range Electricity to the range can be disconnected at the outlet without moving the range if the outlet is in the preferred location remove lower drawer To reduce the risk of burns or fire when reaching over hot surface elements cabinet storage space above the cooktop should be avoided If cabinet storage space is to be provided above the cooktop the risk can be reduced by installing a range hood that sticks out at least 5 beyond the front of the cabinets Cabinets installed above a cooktop must be no deeper than 13 Be sure your appliance is properly installed and grounded by a qualified technician WARNING To reduce the risk of tipping the appliance must be secured by properly installing the Anti Tip bracket packed with the appliance A WARNING All ranges can tip e Injury to persons could result Install anti tip bracket packed with range e See Installation Instructions If you pull the range out and away from the wall for any reason make sure the Anti Tip bracket is engaged when the range is pushed back against the wall Installation Instructions YW Pre Installation Checklist Y Inspect Installation Location Refer to alternate construction section for the following non standard installations a Counter opening extends to the wall Maintop Filler supplied with the range See pag
Download Pdf Manuals
Related Search