Frigidaire GL51HOLPDC (LP) Grill
Contents
1. The grill is made from a non rusting stainless steel After initial usage areas of the grill may discolor from the intense heat given off by the burners this is normal Purchase a mild stainless steel cleaner and rub in the direction of the grain of the metal Specks of grease can gather on the surface of the stainless steel and bake on to the surface and give a worn appearance For removal use an non abrasive oven cleaner in conjunction with a stainless cleaner Note Always scrub in the direction of the grain Rear Infrared Burner Please light and burn the rear infrared burner at least once a month to ensure there is not a build up of debris or grease on the burner This will ensure the ceramic burner will continue to operate as it should 16 gt Trouble Shooting 4 General Trouble Shooting You should inspect the burners at least once a year or immediately if any of the following conditions occur The smell of gas in conjunction with the burner flames appearing yellow The Grill does not reach temperature The burners make a popping noise The Grill heats unevenly Before calling customer service If the Grill does not function properly use the following checklist Problem Solution After opening tank valve be sure one of the Grill control knobs is on high for at least 4 seconds while pushing ignitor button Check tank fuel level Grill will not light when the ignitor button is pushed Check battery rep2. For assistance in designing and building your outdoor cooking center contact a landscape architect or general contractor Review the drawings on the following pages to determine the exact dimensions and items needed for a built in Grill Keep in mind that the gas line hook up is on the right hand side for the main Grill head The structure Grill and support items must be kept level throughout the installation to ensure proper operation Location Take into account convenience and visual impact as well as traffic flow wind exposure and the site s structural suitability The Grill should never be placed in an enclosed area without an approved ventilation system or beneath a combustible overhang Because the Grill exhausts to the rear it should never be located in front of a window or less than 12 from hard to clean surfaces We recommend keeping your gas supply lines as short as possible for best performance To ensure a perfect fit we strongly recommend that you have all components on hand prior to final construction Clearance to Non Combustible Construction For your safety a minimum of 3 clearance from the back of the Grill to non combustible construction is required You should allow at least 6 side clearance to non combustible construction The Frigidaire Grill can be placed directly adjacent to non combustible construction below the cooking surface Outboard Ignitor Plate Installation The electronic ignitors require a standard size
3. Remove the rotisserie when not in use Remove warming shelf when using rotisserie 14 Using the Rotisserie amp Side Burner Rotisserie Lightin Open the lid Push and turn the control knob counter clockwise to the HIGH position Wait 5 seconds Then press and hold the electronic ignitor button You ll hear a snapping sound If the burner does not light in 4 seconds turn the control knob to OFF and wait 5 minutes before trying again Once lit turn the control knob to the desired setting See Fig 18 If the ignitor does not function the burner can be lit with a paperbook match at the tip of the match extender located on the side of the cart to the burn Fig 18 er while the control knob is turned counter clockwise to HIGH See Fig 19 NOTE After the first use the stainless steel around the burner will darken This is a normal occurrence of the non rusting type 304 stainless steel used on the grill The infrared panel will also darken after initial use This is a normal occurrence i eee en a mpa gm Yamn 1a 1 f J o o p p pi Jalea a ee a nes Ti gt lt p ae i pe See 4 i r asm lt e B E pooh hs lt n Sa i n E k i Sig B D 4 P i F r j f 3 a a he i rs f i ive h i l h i i p g a 3 E ke e po i i A F X J m E T a s E ii gt Note Do Not operate the main burners and infrared back burner at the same time S
4. electrical box available at a local hardware store with a minimum depth of 2 5 to be mounted in the structure It should be placed on the left front or left side of the built in island with the center of the ignitor button no more than 3 5 from the Grill The ignitor plate fits over the standard electrical box once mounted in the structure See drawing on following page The ground wire for the ignitor needs to be grounded to a metal structure in order for the ignitor to work Repeat the above steps for the right side ignitor Utilities For natural gas Grills consult your local gas utility company for hook up requirements All gas connections should be made by a plumber or a gas supply company For natural gas installation the supply line must be at least 1 2 diameter The rotisserie requires a 110 120 volt electric supply and GFI receptacle 6 5 amp min If your plan includes a sink arrange for your plumber to run a water line to the site Built In Instructions Side cutouts are needed on each side to feed ignitor wires to the ignitor plates and allow access to side gas connections Note Make sure to use a non combustible base and sides for the structure GFI Electrical outlet for rotisserie motor 6 5 amp min Floor Support area for grill 4 Opening for IGNITOR PLATE access door s INSTALLATION Required Ignitor cutout for front or side mount p counter top 3 5 A minimum 3 clearance is
5. grill This is Very Important 12 Before Lighting Warning Important Before Lighting Check the gas supply line for cuts wear or abrasion Always keep your face and body as far away from the grill as possible when lighting Grill Burner Lighting This unit comes equipped with 2 electronic starters and 5 electrodes The electronic starter located on the right side burner lights the Bottom Infrared Burner which is controlled by Knob 1 and the Side Burner The electronic starter on the left shelf lights the Main Burners which are controlled by Knobs 2 3 4 5 amp 6 The left electronic starter also lights the Back Infrared Burner Lighting the Grill with electronic ignitors Always open the lid before attempting lighting Push and turn one of the control knobs counter clock wise to the HIGH position and immediately press the electronic ignitor button You ll hear a snapping sound It may be necessary to hold the electronic starter button for about 4 seconds If the burner does not light in 4 seconds turn the knob to OFF and wait 5 minutes before trying again Repeat above steps to light remaining burners See Fig 16 Match Lighting If by chance the electronic ignitor does not light the burner the burner may be lit with a paperbook match at the tip of the match lighter extender located on the side of the cart Keep your face as far away from the Grill surface as possible and pass the match extender throu
6. if the smell of gas is detected Before Testing Do Not smoke while leak testing Extinguish all open flames Never leak test with an open flame Mix a solution of equal parts mild detergent or liquid soap and water Testing p Turn off the burner control knobs 2 Turn the top knob of the fuel supply cylinder counterclockwise right to left one rotation to open 3 Apply the soap solution to connections of the fuel supply assembly If no soap bubbles appear the grill is ok to use If bubbles form at the connections a leak is detected If a leak is detected immediately turn off the gas supply tighten any leaking fittings turn gas on and recheck 4 Turn off the knob on the fuel supply cylinder 5 Turn on the burner control knobs for a moment to release the pressure in the hose then turn the control knobs back off 6 Wash off soapy solution with cold water and towel dry If you cannot stop a gas leak turn off the gas supply and call your local gas utility or the dealer you purchased the appliance from If necessary replace the faulty part with a manufacture recommended replacement part Check all gas supply fittings before each use and each time the gas supply cylinder is connected to the regula tor Leak test any time a part of the gas system is replaced Perform a leak test at least once a year whether or not the L P gas supply cylinder has been disconnected 11 Using the Grill Grill Location Do no
7. instructions are not meant to cover every possible condition and situation that may occur Common sense and caution must be practiced when installing operating and maintaining any appliance Questions 1 800 320 0859 Please record Grill information for future reference and service work Model Serial Date of Purchase Gas Type Please retain this manual for future reference 2004 Electrolux Home Products Inc All rights reserved 1 General Safety Instructions IMPORTANT SAFETY INFORMATION ih AFFROVED Read this manual carefully before using your grill to reduce the risk of fire burn hazard or other injury Extreme care should be used because of the high temperatures produced by this appliance CHILDREN SHOULD NOT BE LEFT UNATTENDED IN AN AREA WHERE THE GRILL IS BEING OPERATED This appliance must be kept clear from combustible materials gasoline or other flammable vapors and liquids Do not allow flammable materials to come in contact with grate burner or hot surfaces Do not repair or replace any part of this appliance unless it is specifically recommended in this manual A qualified service techni cian should conduct all other service Follow the installation and servicing instructions provided with this product Have your grill installed by a qualified service techni cian Locate the main gas supply valve so that you know how to shut the gas off to your grill If you smell gas make sure al
8. required between the back of the Maximum distance to center of grill hood and a non combustible ignitor button from side of grill surface Built in dimensions 44 51 57 Single Dual Access Grill Grill Grill Door Access Door T 44 1 3 51 1 4 57 1 5 EA 20 74 2074 25 11e N A 2 ma na wa 180 f 36w sw 18 Additional Requirements Gas connection cut out in floor support needs to be 4 wide x 6 long set 6 back from front edge Tonitor cutout is equal to a standard electrical outlet with a minimum depth of 2 2 If using a backsplash apron or rear wall locate electrical service on the left hand side for rotisserie motor connection A minimum clearance of 12 from the back must be maintained between the grill and any combustible construction such as wood siding of a residence 3 minimum for non combustible construction mm Gas Requirements General Information Verify the type of gas supply to be used either Natural Gas NG or Liquid Propane L P and make sure the marking plate located on the back of the unit agrees with that of the supply Note Never attach an unregulated gas line to the appliance For Natural Gas installations an installer must supply a gas shutoff valve that is easily accessible to the grill All installer supplied parts must conform to local codes or in the absence of local codes with the National Electrical Code ANSI NFPA 70 1990 and the Na
9. up the three cutouts on the underside of the burner See Fig 9 5 Install burner cap onto burner See Fig 10 Fig 6 Cutouts N Interior parts installation IN l Check to make sure the bottom Flavor Grids are correctly installed in the cutouts and around the ignitors as they may have shifted during shipment See Fig 11 Fig 11 2 Insert the second row of Flavor Grids into _ Bottom Flavor Grids i in between burners cutouts with triangle ridges facing up See Fig 12 Cutouts 3 Install cooking grates on the ledges provided on the grill to create your cooking surface See Fig 13 4 Place warming shelf on support brackets by setting it flat across brackets allowing the two holes to line up with the stops on each bracket See Fig 14 ti WELE i y iis TEGEIDEL TR M j lesdedevesasae tess SpE S Fig 14 Built In Instructions The Frigidaire Grill can be installed as a built in Grill If installed as a built in Grill the Grill surround must be constructed of Non combustible material Planning and Design Start by identifying the number and size of components you want to include Grill side burner access doors for storage or other items you may wish to furnish such as refrigerator sink warming drawer Countertops must be constructed with non combustible outdoor safe materials Consider outdoor lighting to illuminate after dark Grilling
10. See Fig 3 4 Re insert the battery positive side first and spring assembly and attach the ignitor cap See Fig 4 5 Repeat above steps for second ignitor on the Side Burner GL51 Ignitor Assembly Side Burner Double Wire Left Shelf Four Wire hey Side Shelf Side Burner Assembly Side Shelf and Side Burner Attachment Loosen the bolts on the side of the grill and attach the shelf by allowing the bolt heads to fall through the large opening in the bottom of the keyhole slots Then slide the shelves downward until the bolts are resting against the top of the key hole slots Tighten all of the shelf bolts See Fig 5 Zi Attach the wires coming out from the sides of the grill to the ignitor terminals See Fig 6 Note It does not matter which wire goes to which terminal on the four wire ignitor l Attach the side burner by allowing the bolt heads to fall through the large opening in the bottom of the keyhole slots Then slide the side burner downward until the bolts are resting against the top of the key hole slots Tighten all of the side burner bolts 2 Screw the Flex Line coming from the side of the grill to the fitting on the bottom of the Side Burner See Fig 7 3 Attach the ignitor wires coming out from the side of the grill to ignitor terminals See Fig 8 Note It does not matter which wire goes to which terminal on the two wire ignitor 4 Install burner into side burner tray lining
11. Use e Care Manual Assembly Instructions Included 51 Stainless Steel Outdoor Grill with Electronic Ignition Gallery Series z a N i ON qa N i x e k lt a 3 ith G a i E L b ba iok i Hi ppe am Sey La n o aa Visit the Frigidaire Web Site at http www frigidaire com Welcome Product Registration General Safety Instructions 2 Grill Features amp Components 3 Grill Assembly Built In Instructions 48 Gas Requirements Leak Testing Using the Grill Rotisserie Side Burner Usage Lighting the Grill Care amp Maintenance Before You Call Trouble Shooting Warranty cece 19 amp READ AND SAVE THESE INSTRUCTIONS MADE IN THE U S A Welcome amp Congratulations Congratulations on your purchase of a new gas grill At Electrolux Home Products we are very proud of our product and are completely committed to providing you with the best service possible Your satisfaction is our number one priority We know you ll enjoy your new gas grill and Thank You for choosing our product We hope you consider us for future purchases PLEASE CAREFULLY READ AND SAVE THESE INSTRUCTIONS This Use amp Care Manual provides specific operating instruction for your model Use your gas grill only as instructed in this manual These
12. d warranty does not cover any scratches dents corrosion or discoloring by heat abrasive and chemical cleaners nor any components used in the installation of the appliance E e e e e e e e e E e e e eee eee e e e e e e e e e e ee ee e e ee ee e e e e e e e A ee If you have other questions please contact Customer Service Hotline 800 320 0859 Because of continuing product improvement these specifications are subject to change without notice GL51IMD 4 2004 19
13. g Spider and insects can nest in the burners of this or any other Grill and cause the gas to flow from the front of the burn er This is very dangerous condition which can cause a fire to occur behind the valve panel thereby damaging the Grill and making it unsafe to operate We recommend you check at least once a year to be safe 18 Warranty LIMITED LIFETIME WARRANTY Frigidaire Grills have a Lifetime Warranty on all stainless steel panels 15 years on stainless burners and a 5 year warranty on all other parts IMPORTANT We recommend you return the warranty registration card so that you can be contacted with any questions of safety arise that could affect you The return of the warranty registration card is not a condition for watranty coverage LIMITED WARRANTY If the Frigidaire Grill does not operate properly first thoroughly carry out the instructions provided with the unit to ensure that the appliance is installed correctly and check the Troubleshooting section The warranty is nontransferable The warranty is for replacement of defective parts only Frigidaire will not be responsible for damage resulting from accident alteration misuse abuse hostile environments improper installation or installation not in accordance with local codes This limited warranty does not cover corrosion or discoloring due to lack of maintenance misuse hostile environments alterations accidents or abuse or neglect eThis limite
14. gh the spaces in the Grill rack to the ports of the back crossover burner between the flavor grids Position the match near the burner ports and push and turn the control knob counter clockwise to the HIGH position See Fig 17 Note If the grill will not light after several attempts see the Trouble shooting section of this manual Turn the control knobs to the OFF position when not in use 13 Back Infrared 6 ie 3 Knob Left electric starter For Main Burners 2 3 4 5 amp 6 and Back Infrared Burner Lighting the Grill Knob Knob 5 4 Do not attempt to Right electric starter For Bottom Infrared Burner knob 1 amp Side Burner Light the grill if the odor of gas is present Fig 16a Using the Rotisserie amp Side Burner The grill rotisserie system is designed to cook items from the back using infrared heat The rotisserie burner is an infrared type which provides intense searing radiant heat Preferred by chefs over other cooking methods this intense heat is magnificent for searing in the natural juices and nutrients found in quality cuts of meats Once lit the rotisserie burner will reach cooking temperatures in 1 minute The orange red glow will even out in about 5 minutes The rotisserie motor is equipped with metal gears and is capable of turning up to 20 lbs of food The motor is mounted on a bracket on the left side of the grill by sliding the motor ove
15. ide Burner Lighting Push and turn the control knob to the HIGH position and immediately press and hold the electronic ignitor button You ll hear a snapping sound It may be necessary to hold the electronic starter button for about 4 seconds If the burner does not light in 4 seconds turn the knob to the OFF position and wait 5 minutes before trying again Repeat above steps to light remaining burners See Fig 20 Fig 20 Match Lighting If by chance the electronic ignitor does not light the burner the burner may be lit with a paperbook match at the tip of the match extender located on the side of the cart Keep your face as far away from the burner as possible and place a lit long stem match through the spaces in the grate to the ports of the burner Position the match near the burner ports and push and turn the control knob to the HIGH position 15 Care and Maintenance Drip Tray The drip tray located below the grill inside the cart should be cleaned periodically to prevent heavy buildup of debris Note Allow the drip tray to cool before attempting to clean Cooking Grates The cooking grates can be cleaned immediately after cooking is completed and after turning off the flame Wear a barbecue mitt and scrub the cooking grates with a damp cloth If the grill is allowed to cool down cleaning the grates will be easier if removed from the grill and cleaned with a mild detergent Stainless Steel
16. l gas connections are tight before operation If you continue to smell gas call a qualified technician When lighting a burner always pay close attention to what you are doing Be certain you are pushing the ignitor that lights the burner you intend on using FOR YOUR SAFETY TESTED IN ACCORDANCE WITH ANSI 721 58b 2002 CGA 1 6b M02 STANDARD FOR If you smell gas OUTDOOR COOKING GAS APPLIANCES THIS GRILL IS FOR OUTDOOR USE ONLY 1 Shut off gas to the appliance Check your local building codes for the proper 2 Extinguish any open flames method of installation In the absence of local 3 Open lid codes this unit should be installed in accordance 4 If odor continues immediately with the National Fuel Gas Code No Z223 1 2002 call your gas supplier and the National Electrical Code ANSI NFPA No 70 1990 CALIFORNIA PROPOSITION 65 WARN ING The Burning of gas cooking fuels generates some by products which are on the list of substances FOR YOUR SAFETY which are known by the State of California to cause cancer or reproductive harm California law requires businesses to warn customers of potential exposure to such substances To minimize exposure to these sub stances always operate this unit according to the use and care manual ensuring you provide good ventila tion when cooking with gas DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance An LP cylinder not connected for u
17. lace battery Remove the cooking grates and flavor grids Push ignitor button and check for spark on tip of electrode Check to see if debris is blocking the electrode sparks Check for loose wire connections Attempt to match light the burner If using L P gas disconnect gas line at tank then reconnect Check for proper gas supply and pressure l l l r If using L P gas check for low fuel level Low heat with knob in High position If using L P gas check for kinks in supply line If only one burner appears low clear burner ports of any obstructions Pre heat Grill for a full 10 minutes If using L P gas disconnect gas line at tank then reconnect 17 Trouble Shooting N 7 Problem Solution Check gas connection Flame is erratic Fuel level may be low Grill may be in need of cleaning Check flavor grids and cooking grates for excess build up Ensure Grill is not placed directly in path of wind Be sure the drip tray is clean do not use aluminum foil in drip tray Check the burner inlet for obstructions Burner flame is yellow or orange in conjunction with the odor of gas Grill may be in a windy area Move to a less windy area if possible Loosen the four bolts that attach grill head to Cart door does not align properly with cart cart Slide grill head either to the left or right until door is aligned properly Retighten the bolts Spider and Insect Warnin
18. r the bracket with the cord facing the back of the grill Make sure the motor 1s straight prior to operating Warning Electrical Grounding Instructions This appliance rotisserie motor is equipped with a three prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded three prong receptacle Do not cut or remove the grounding prong from this plug Attaching the Rotisserie The motor is mounted on a bracket on the left side of the grill by sliding the motor over the bracket with the cord facing the back of the grill With the rotisserie motor in place and plugged into an electrical outlet it is now ready to operate After installing rotis rod handle slide one of the meat forks onto the rod prongs facing away from the handle Push the rod through the center of the food then slide the second meat fork onto the rod prongs toward the food Center the food to be cooked on the rod then push the meat forks firmly together Tighten the wing nuts It may also be necessary to wrap food with butcher s string never use nylon or plastic string to secure loose portions Once the food is secure insert the pointed end of the rotis rod into the motor assembly and rest the other end on the support on the right hand side of the Grill If needed remove the cooking grates for more room Turn the power switch to the On position to start the rotisserie motor Note
19. s must not be stored in a building garage or any other enclosed area The L P cylinder must have an overfill protection device OPD on it The L P Gas supply cylinder must be constructed and marked in accordance with the specifications for L P gas cylinders of the U S Department of Transportation DOT or the National Standard of Canada CAN CAS B339 Cylinders Spheres and Tubes for the Transportation of Dangerous Goods When not in use gas supply cylinder valve is to be in the OFF position eThe tank supply system must be arranged for vapor withdrawal LP Tank must be kept in an upright position eThe regulator and hose assembly must be inspected before each use of the grill If there is excessive abrasion or wear or if the hose is cut it must be replaced prior to the grill being used again eCylinders must be stored outdoors out of the reach of children and must not be stored in a building garage or any other enclosed area Never fill the cylinder beyond 80 full Do not store a spare LP gas cylinder under or near this appliance 10 Leak Testing General Information Although all gas connections on the grill are leaked tested at the factory prior to shipment a complete gas tightness check must be performed at the installation site due to possible mishandling in shipment or exces sive pressure unknowingly being applied to the unit Periodically check the whole system for leaks or imme diately check
20. se shall not be stored in the vicinity of this or any other appliance WARNING This appliance is not intended to be DO NOT try lighting this appliance without reading installed in or on recreational vehicles or boats the LIGHTING INSTRUCTIONS section of this manual FOR OUTDOOR USE ONLY Roll top grill hood Grilling Cooking surface Side Shelf Control knob back infrared burner Control knobs main burners Warming drawer Handle Grill Features GLS51 Warming shelf Infrared back burner Electronic ignitors main rear infrared amp side burner Cart w doors Drip Pans Side Burner Control knob side burner Control knob bottom infrared burner Grill Assembly Note Prior to assembly remove protective film from stainless steel parts Assembly requires 4 tools and a Friend Tools required 1 4 socket wrench Cap Fig 1 1 2 socket wrench Sary adjustable wrench Assembly oe Mounting ut Cylinder Bracket SCISSOrsS Ignitor Attachment l Remove the ignitor cap spring assembly bat tery and lock nut from ignitor See Fig 1 2 Insert the threaded section of the ignitor into the U shaped cut out of the ignitor mounting bracket See Fig 2 3 Insert the threaded section of the ignitor through the hole in the shelf and secure to shelf using the lock nut Use the ignitor assembly diagrams to determine which ignitor goes with which shelf Tighten Securely
21. t use the grill in garages breezeway sheds or any enclosed area Never operate the grill in enclosed areas as this could lead to a carbon monoxide buildup which could result in injury or death Place the grill on a level surface Avoid moving the grill while it 1s operation Note The grill will operate best if it is not facing directly into the wind Clearance to combustible construction A minimum of 12 from the sides and back must be maintained from the gas grill above and below the cooking surface to adjacent vertical combustible construction Clearance to non combustible construction A minimum of 3 clearance from the back of the grill to non combustible construction is required for the lid to fully open General Rules Do Not leave the grill unattended while cooking l Make sure the grill has been leak tested and is properly located 2 Light the grill burners using the instructions on this page 3 Turn the control knobs to High and preheat the grill for 10 minutes 4 Place the food on the grill and cook to the desired doneness Adjust heat setting between High and Low if necessary 5 Allow grill to cool down and clean the drip tray after each use Keep any electrical supply cord and the fuel supply hose away from any heated surfaces The location of the burner tube with respect to the the orifice is vital for safe operation Check to ensure the orifice is inside of the burner tube before using your
22. tional Fuel Gas Code ANSI Z223 1 1998 All pipe sealants must be an approved type and resistant to the actions of L P gases Never use pipe sealant on flare fittings All gas connections should be made by a competent technician and in accordance with local codes and ordinances In the absence of local codes the installation must comply with the National Fuel Gas Code ANSI Z223 1 1998 Gas conversions kits are available from the factory When ordering gas conversion kits have the model number and the type of gas natural or L P from your grill This appliance and its individual shut off valve must be disconnected from the gas supply piping system dur ing any pressure testing of that system at test pressures in excess of 1 2 PSIG 3 5 kPa This appliance must be isolated from the gas supply piping system by closing its individual manual shut off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1 2 PSIG 3 5 kPa The installation of this appliance must conform with local codes or in the absence of local codes with National Fuel Code ANSI Z223 1a 1998 Installation in Canada must be in accordance with the Standard Can1 b149 1 and or 2 installation code for gas burning appliances and equipment and local codes Natural Gas Installation The gas inlet supply pressure should be between 5 and 14 w c A step down regulator is required if the line pressure is in excess of 14
23. w c Check your local gas utility company or with local codes for instructions on installing gas supply lines Be sure to check on type and size of run and how deep to bury the line If the gas supply line is too small the grill will not operate correctly Any joint sealant used must be an approved type and be resistant to the actions of L P gases Place the installer supplied shut off valve in an accessible location to enable the gas supply to be cut off to the unit Gas Requirements L P Gas Installation Frigidaire Gas Grills that are set to operate with L P gas come with a high capacity hose and regulator assembly Note Only use the pressure regulator and hose assembly supplied with the grill or a replacement pressure regulator and hose assemblies specified by Frigidaire This assembly is designed to connect directly to a standard 20 Ib L P cylinder Attach the gas hose assembly to the brass 3 8 flared fitting using an adjustable wrench on the under side of the grill Tighten securely and attach other end to the propane tank sold separately See Fig 15 Fig 15 L P Tank Information Never use a dented or rusted L P tank or cylinder with a damaged valve The L P cylinder must be provided with a shut off valve terminating in an L P gas supply cylinder outlet specified as applicable for connection No 510 in the standard for compressed gas cylinder valve outlet and inlet connection ANSI CGA V 1 Cylinder
Download Pdf Manuals
Related Search