Alpine TMX-R705 7" Monotorized wide screen overhead monitor
Contents
1. JR Use 12V 5W rated bulb End Cap Base T8 x 28 available at any autoparts store or consult your authorized Alpine Mobile Multimedia dealer for further information Use a flat bladed screwdriver to release the hooks and open the lense being careful not to scratch the product Pry at two recessed points at rear of lense Be careful not to crack the lense Change the bad bulb and press the lense back in place Lense 4 Hooks 4 Hooks Ilen Information In Case of Difficulty If you encounter a problem please review the items in the following checklist This guide will help you isolate the problem if the unit is at fault Otherwise make sure the rest of your system is properly connected or consult your authorized Alpine dealer No function or display Car s ignition is off Turn the ignition on No fuse or blown fuse Check the cause and replace the fuse Incorrect connections Check connection and remedy Vehicle s battery is weak Check the voltage of vehicle s battery Unclear picture display Fluorescent tube is exhausted Replace the fluorescent tube No picture display Brightness control is set for minimum brightness control Adjust the brightness Incorrect setting of the VCR mode Switch to the correct mode Protective circuit is on because of high temperature Wait until the temperature inside the vehicle comes down to the2. Adjust the monitor s angle for better visibility 1 While viewing the screen that is shown press the ANGLE V or A button to adjust the display to the ideal viewing angle The display viewing angle can be adjusted between about 80 and 105 degrees Press the lt or gt button to adjust the right left viewing angle It is possible to adjust the display viewing angle up to about 15 degrees to the left or right Press and hold the OPEN CLOSE button of the main unit for at least 2 second This will return the monitor quickly to its center viewing position NOTES The angle changes continuously if the ANGLE W and A buttons or the and buttons are held down If there are any obstructions to the monitor when adjusting the angle first remove the obstruction and then readjust the angle The screen color will vary when viewed at certain angles Adjust the screen angle for the best viewing position If the voltage of the vehicle s battery power is low the screen may blink when the screen angle is changed This is normal and not a malfunction The adjusted angle is stored in the memory Gen Adjusting the Volume 1 Press the or A button to adjust the volume NOTE The volume changes continuously if the w or button is held down This operation will affect the headphone and External Audio outputs only The IR signal for the wireless headphones are not affected Audio Mute Function Activating this
3. Cette garantie couvre les produits audio visuel de voiture et les accessoires connexes le produit Elle ne couvre les produits que dans le pays o il ont t achet s DUR E DE LA GARANTIE Cette garantie est en vigueur pendant un an partir de la date du premier achat du client GARANTIE VIE DES T TES DE LECTURE DES MAGNETOPHONES A CASSETTES Toutes les t tes de cassettes analogiques audio de voiture Alpine l exception des tes de cassettes vid o sont garanties vie contre des vices de fabrication pouvant entrainer leur panne PERSONNES PRO T G ES PAR LA GARANTIE Seul l acheteur original du produit s il r sisde aux Etats Unis Porto Rico ou au Canada peut se pr valoir de la garantie CEQUI ESTCOUVERT Cette garantie couvre tous les d fauts de mat riaux et de fabrication pi ces et main d uvre du produit CE QUI N EST PAS COUVERT Cette garantie ne couvre pas ce qui suit D Les dommages survenus durant le transport des produits renvoy s Alpine pour tre r par s les r clamations doivent tre adress es au transporteur Tout d g t provoqu par accident abus n gligence usage inappropri mauvais raccordement mauvaise utilisation ou par le non respect des instructions indiqu es dans le manuel de l utilisateur 8 Les dommages dus la force majeure notamment aux tremblements de terre au feu aux inondations aux temp tes ou aux autres cataclysmes n
4. monitor When the movable monitor is opened do not place any object on the monitor and be careful not to bump or apply any pressure to the monitor while it is open This can cause damage to the mechanism Under low ambient temperature conditions the display may be dark for a short period of time immediately after the power is turned on Once the LCD has warmed up the display will return to normal The TMX R705 draws minimal current even when its power switch is turned off If the switched power ignition lead of the TMX R705 is connected directly to the positive post of the vehicle s battery the battery may be discharged If this lead is unswitched it must be disconnected from the battery post should the vehicle be left unused for an extended period of time Press the OPEN CLOSE button of the main unit or press the POWER button press and hold the OPEN CLOSE button of the supplied remote control for at least 2 seconds The unit beeps 3 times and closes the monitor automatically Then the power of the monitor turns off NOTE Since this is an overhead monitor the display will be lowered when opened and raised when closed If the monitor touches an obstacle while it is being raised the unit will stop immediately Should this occur remove the obstacle and press the OPEN CLOSE button again to close the monitor SEN Basic Operations Bde VOLUME MUTE DISPLAY Adjusting the Monitor Viewing Angle
5. the Dome light remains on all the time 8 Dome Light Door Trigger Blue Green Connect to the factory door switch NOTES Have the switching done being the power cord taken off Have the switching done accurately If you make mistakes in setting the dome light remains lit and it may cause running down of the battery Vehicle Door polarity depending on the vehicle type can be changed by the Door SW polarity where is located on the left side of the main unit Default Negative Switched System NEG DOOR SW POLARITY POS Positive Switched System Negative Switched System 1 sas ids GND GND ss UD 12V 4 Remote Turn ON Blue White Connecting to other device such as a small amplifier to turn them ON synchronizing with the TMX R705 power ON It gives 12V when the power is ON 5 GND Black This is a common Ground for the main unit and the Dome light Another GND line connects to Pin 2 of the external dome light SW 6 BATT Dome Light Yellow Green This is a constant 12V for the Dome light Connect to the Dome light 12V line on the vehicle BATT Main Unit Yellow This is a constant 12V for the main unit It is recommended that separate connections from the Dome light battery line are used to avoid noise and over current Fuse Holder 5A 9 KWE 508V Included KWE 508V Sold Separately 2 IGN ACC Red This wire connects to the ignition or accessor
6. operating temperature range 45 C Picture color is poor Brightness Color Tint control are not set to the proper positions Check each control Spots or dotted lines stripes appear Caused by neon signs high voltage power lines CB transmitter other vehicle s ignition plugs etc Change the location of your vehicle The display angle cannot be adjusted or the adjustment screen does not appear Mechanism error Press the OPEN CLOSE button to stow away the display and raise the display again Noise is picked up by the Wireless Headphone pice separately or the sound is inaudible Wireless Headphone is being used in a place exposed to direct sunlight Use in an environment that is not exposed to direct sunlight Wireless Headphone batteries are exhausted Replace the batteries The fluorescent tube replacement is not free of charge even within the warranty period for the tube is an article of consumption 12 N Specifications MONITOR SECTION Screen Size LCD Type Operation System Number of Picture Elements Effective Number of Picture Elements Illumination System GENERAL Power Requirement Operating temperature Weight DIMENSIONS Width Height Depth NOTES 7 0 Transparent type TN LCD TFT active matrix 336 960 pes 1 440 x 234 99 99 or more Cold cathode fluorescent tube 14 4V DC 11 15 V allowable 32 F to 113 F 0 C to 45 C 2 0 kg 4 Ibs 7 oz 22
7. or gt button within 10 seconds to adjust the tint SET UP AUX1 BRIGHT 0 COLOR 0 PINT 0 sos G 4 Press the SETUP button to finish adjustments Setting the Brightness of the Backlight The brightness of the LCD panel s backlighting is adjustable to more closely match the vehicle s interior lighting This makes the screen easier to view 1 Press the SETUP button 2 Press the V or A button within 10 seconds and select DIMMER 3 Press the 4 or gt button within 10 seconds to set the value AUTO The screen brightness will dim when the headlight switch is turned on if proper connections are made HIGH Maximum screen brightness LOW The preset screen brightness that was set when adjusting the minimum backlight level SET UP AUX1 bIDIMMER AUTO DIMMER Lv AT CLOSE OFF AUTO HIGH LOW 4 Press the SETUP button to finish adjustments Adjusting the Lowest Level of the Backlight The minimum brightness level for the backlighting LOW is adjustable This is used to match the screen brightness to the dashboard especially at night This setting is recalled whenever the vehicle s headlight switch is turned on in the AUTO Dimmer mode 1 Press the SETUP button 2 Press the V or A button within 10 seconds and select DIMMER Lv 3 Press the lt or gt button within 10 seconds to set the v
8. 8 mm 8 15 16 55 mm 2 3 16 267mm 10 1 2 Due to continuous product improvement specifications and design are subject to change without notice The LCD panel is manufactured using an extremely high precision manufacturing technology Its effective pixel ratio is over 99 9996 This means that there is a possibility that 0 0196 of the pixels could be either always ON or OFF Installation and Connections Before installing or connecting the unit please read the following and pages 2 and 3 of this manual thoroughly for proper use AN Warning MAKE THE CORRECT CONNECTIONS Failure to make the proper connections may result in fire or product damage USE ONLY IN CARS WITH A 12 VOLT NEGATIVE GROUND Check with your dealer if you are not sure Failure to do so may result in fire etc BEFORE WIRING DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL Failure to do so may result in electric shock or injury due to electrical shorts DO NOT ALLOW CABLES TO BECOME ENTANGLED IN SURROUNDING OBJECTS Arrange wiring and cables in compliance with the manual to prevent obstructions when driving Cables or wiring that obstruct or hang up on places such as the steering wheel gear lever brake pedals etc can be extremely hazardous DO NOT SPLICE INTO ELECTRICAL CABLES Never cut away cable insulation to supply power to other equipment Doing so will exceed the current carrying capacity of the wire and result
9. INE Japan Printed in Japan S 68P41262Y72 O ENGLISH Contents m_e iaa information O perating Instruc tions In Case of Difficulty esses 12 A WARNING Speciticalions en ie Pr pd 12 WARNING n es 2 CAUTION eiii etes 3 Insta lation a nd C onnections PRECAUTIONS eene 3 AV Ew ER 13 C AUtiOD ooa orien io ERR 13 Basic Operations PI C utlolis 2 ng IREe eri prete 14 Parts Names of the Overhead Monitor 4 Mounting Instruction eee 15 Opening the Monitor Display 5 Connections ssesseeseeeee eene nnne 16 Closing the Monitor Display 5 Adjusting the Monitor Viewing Angle 6 LIMITED WARRANTY Adjusting the Volume eese 6 Audio Mute Function 6 Switching the Source sss 6 Switching Display Modes 7 Other Useful Features Adjusting Brightness of Picture 8 Adjusting Color Density of Picture 8 Adjusting Tint of Picture 8 Setting the Brightness of the Backlight 8 Adjusting the Lowest Level of the Backlight 9 Setting Automatic Closing of Monitor 9 Dome Light Settings sinus 10 Battery Replacement 11 Replacing the Dome Light Bulb 11 Len AN WARNING WARN
10. ING This symbol means important instructions Failure to heed them can result in serious injury or death DO NOT OPERATE ANY FUNCTION THAT TAKES YOUR ATTENTION AWAY FROM SAFELY DRIVING YOUR VEHICLE Any function that requires your prolonged attention should only be performed after coming to a complete stop Always stop the vehicle in a safe location before performing these functions Failure to do so may result in an accident KEEP THE VOLUME AT A LEVEL WHERE YOU CAN STILL HEAR OUTSIDE NOISE WHILE DRIVING Failure to do so may result in an accident MINIMIZE DISPLAY VIEWING WHILE DRIVING Viewing the display may distract the driver from looking ahead of the vehicle and cause an accident DO NOT DISASSEMBLE OR ALTER Doing so may result in an accident fire or electric shock USE THIS PRODUCT FOR MOBILE 12V APPLICATIONS Use for other than its designed application may result in fire electric shock or other injury KEEP SMALL OBJECTS SUCH AS BATTERY OUT OF THE REACH OF CHILDREN Swallowing them may result in serious injury If swallowed consult a physician immediately DO NOT PLACE HANDS FINGERS OR FOREIGN OBJECTS IN INSERTION SLOTS OR GAPS Doing so may result in personal injury or damage to the product USE THE CORRECT AMPERE RATING WHEN REPLACING FUSES Failure to do so may result in fire or electric shock Zen DO NOT BLOCK VENTS OR RADIATOR PANELS Doing so may cause heat t
11. ND Black Ext A V Select Pink Blue IR Remote Out White Brown To Audio Video Output Terminals 22 PO Video Game Console Sold Separately To other monitor Common Ground Black as s 8 a ue Connect to the cable 29023 Bs Right Positive Green of the vehicle side XE xE Ss8 29 g29 Sac toto Bs B oo Rear View GND Black 9 Dome Light Always ON Red er D Dome Light Door Blue Green g Dome Light lgnition Red Remote Turn on Blue White Rocker switch is ccessory Ignition Re Dome Light Battery Yellow Green located on Alpine GND Black Q overhead console Ext A V Select Pink Blue 3 Battery Yellow IR Remote Out White Brown To AUX Output gt 0 For Front Monitor Sold Separately IVA C801 etc For Front Monitor Tune Box Ai NET HE Connector 5 amp x Remote Out Aux 1 2x White Brown lt 15 ez g o To Audio Video E Output Terminals 5 Remote IN 953 White Brown 844 i oO VPE V180A DVD Changer Sold Separately Sold Separately Ai NET Connector 16e D Dome Override Always OFF Gray Green Connecting to Pin 1 of the external dome light SW When it is grounded the Dome light remains off all the time 2 Dome Override Always ON Red Green Connect to Pin 3 of the external dome light SW When it is grounded
12. S RELATING TO THE CARE AND CUSTODY OF THE PRODUCT THE TERM CONSEQUENTIAL DAMAGES REFERS TO THE COST OF REPAIRING OR REPLACING OTHER PROPERTY WHICH IS DAMAGED WHEN THIS PRODUCT DOES NOT WORK PROPERLY THE REMEDIES PROVIDED UNDER THIS WARRANTY ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS HOW STATE PROVINCIAL LAW RELATES TO THE WARRANTY This Warranty gives you specific legal rights and you may also have other rights which vary form state to state and province to province In addition some states provinces do not allow limitations on how long an implied warranty lasts and some do not allow the exclusion or limitation of incidental or consequential damages Accordingly limitations as to these matters contained herein may not apply to you IN CANADA ONLY This Warranty is not valid unless your Alpine car audio product has been installed in your vehicle by an Authorized Installation Center and this warranty stamped upon installation by the installation center HOW TO CONTACTC USTOMER SERVICE Should the product require service please call the following number for your nearest Authorized Alpine Service Center U S A CANADA 1 800 ALPINE 1 1 800 257 4631 1 800 ALPINE 1 1 800 257 4631 Alpine Electronics of America Inc 19145 Gramercy Place Torrance California 90501 U S A Alpine Electronics of Canada Inc Suite 203 7300 Warden Ave Markham Ontario L3R 9Z6 Canada
13. ZLLLPINE OWNER SMANUAL Please read before using this equipment MODE D EMPLOI Veuillez lire avant d utiliser cet appareil TMX R705 Mobile Overhead Monitor MANUAL DE OPERACI N L alo antes de utilizar este equipo ALPINE ELECTRONICS INC Tokyo office 1 1 8 Nishi Gotanda Shinagawa ku Tokyo 141 8501 Japan Tel 03 3494 1101 ALPINE ELECTRONICS OF AMERICA INC 19145 Gramercy Place Torrance California 90501 U S A Tel 1 800 ALPINE 1 1 800 257 4631 ALPINE ELECTRONICS OF CANADA INC Suite 203 7300 Warden Ave Markham Ontario L3R 9Z6 Canada Tel 1 800 ALPINE 1 1 800 257 4631 Sankei Kikaku Co Ltd 1 13 38 Hinodai Hino Tokyo Japan ALPINE ELECTRONICS OF AUSTRALIA PTY LTD 6 8 Fiveways Boulevarde Keysborough Victoria 3173 Australia Tel 03 9769 0000 ALPINE ELEC TRONICS FRANCE S A R L RCS PONTOISE B 338 101 280 98 Rue De La Belle Etoile Z I Paris Nord Il B P 50016 F 95945 Roissy Charles De Gaulle Cedex France Tel 01 48 63 89 89 ALPINE ELECTRONICS OF UK LTD 13 Tanners Drive Blakelands Milton Keynes ALPINE ELECTRONIC S GmbH Kreuzerkamp 7 11 40878 Ratingen Germany Tel 02102 45 50 ALPINE ITALIA S p A A MK14 5BU U K Via C Colombo 8 svi R Sul Naviglio Tel 01908 61 15 56 Tel 02 48 47 81 ALPINE ELECTRONICS DE ESPANA S A Portal De Gamarra 36 Pabell n 32 01013 Vitoria Alava Apdo 133 Spain Tel 34 45 283588 Designed by ALP
14. ain Door Open The dome light will remain OFF until the vehicle s door is closed and re opened The dome light will return to Auto mode To switch ON the dome light manually press the DOME LIGHT button again With the dome light ON and the vehicle s door OPEN press and hold the DOME LIGHT button for at least 3 seconds The dome light will be switched OFF permanently regardless of the opening and closing of the vehicle s doors To cancel with the vehicle s door open press and hold the DOME LIGHT button for at least 3 seconds NOTE If the Override button is connected it will always work regardless of the Remote Dome Light Status 10 n Battery Replacement Replacing the Dome Light Bulb Applicable battery Use two AAA sized dry batteries or equivalent Point the remote control transmitter toward the remote sensor on the TMX R705 and use the remote control within 2 meters from the TMX R705 1 Opening the battery cover Slide out the battery cover while firmly pressing in the direction of arrow 2 Replacing the battery Put the batteries in the case observing the polarities as illustrated 3 Closing the cover Push the cover as illustrated until a click is heard NOTE When replacing the dome light bulb replace with one of the specified 12V 5W capacity Use of a different capacity bulb may cause damage to the unit Please note that no guarantee is carried out if this is the case
15. alue SET UP AUX1 DIMMER AUTO DIMMER Lv ATCLOSE OFF LOW HIGH 4 Press the SETUP button to finish adjustments Setting Automatic Closing of Monitor Simply turn the ignition key to OFF to automatically close the monitor display 1 Press the SETUP button 2 Press the V or A button within 10 seconds to select AT CLOSE 3 Press the lt or gt button within 10 seconds to set the value AUTO Automatic closing of the display in depending upon whether the ignition switch is ON or OFF If you press the POWER button or the OPEN CLOSE button while the monitor is being opened or closed the monitor stops opening or closing even if AUTO setting is on and cannot be closed automatically In this case press the POWER button or the OPEN CLOSE button again to close the monitor OFF Manual closing of the display SET UP AUX1 DIMMER AUTO DIMMER Lv P ATCLOSE OFF AUTO OFF 4 Press the SETUP button to finish adjustments Qen Other Useful Features DOME LIGHT Dome Light Settings 1 Press the DOME LIGHT button to turn the Dome Light ON or OFF regardless of whether the vehicle s doors are open or closed Door Closed The dome light will remain lit until the vehicle s door is opened and closed The dome light will return to Auto mode To switch OFF the dome light manually press the DOME LIGHT button ag
16. aturels 4 Les frais ou les d penses relatifs l enl vement ou la r installation du produit Les services rendus par une personne physique ou morale non autoris e Les produits dont le num ro de s rie a t effac modifi ou retir 2 Les produits qui ont t adapt s ou modifi s sans le consentement d Alpine Les produits qui ne sont pas distribu s par Alpine aux Etats Unis Porto Rico ou au Canada 8 Les produits qui n ont pas t achet s par l entremise d un concessionnaire Alpine autoris Tout produit qui a t d termin comme contenant une quantit excessive de poussi re ou de salet et tout produit qui contient d autres salet en ce compris du liquide et des corps trangers COMMENTSE PR VALOIR DE LA GARANTIE D II vous faut remettre le produit n cessitant des r parations un centre de service autoris Alpine ou Alpine m me et en assumer les frais de transport Alpine a le choix entre r parer le produit ou le remplacer par un produit neuf ou r vis le tout sans frais pour vous Si les r parations sont couvertes par la garantie et si le produit a t envoy un centre de service Alpine ou Alpine le paiement des frais de r exp dition du produit incombe Alpine Vous devez donner une description d taill e des probl mes qui sont l origine de votre demande de r paration 8 Vous devez joindre la preuve de votre achat du produit 4 Vous deve
17. ay be needed 1 Press the OPEN CLOSE button of this unit or press the POWER button press and hold the OPEN CLOSE button of the supplied remote control for at least 2 seconds The monitor will automatically open and close with each press NOTES Do not forcibly open or close the monitor Doing so will cause damage The monitor cannot be opened or closed unless the unit is turned upside down 3 2 Use the supplied remote control to adjust the view angle of the monitor as required See Page 6 Adjusting the Monitor Viewing Angle NOTE Do not forcibly change the view angle of the monitor Doing so may cause damage After opening the monitor display and adjusting the viewing angle move the battery line off before installing the unit Use 4 screws and attach to the mounting plate Screw holes are hidden under the panel Therefore the panel has to be opened Two rear side screw holes are located under the mechanism cover plate After installing the unit reconnect the battery line which you moved off before Screws Console If you have any problem for the installation please contact to ALPINE Tech Support 15 Installation and Connections Connections o E a 4 z o c o z gt x lt x LLI LL z z Q Q E z E E wo 1O El co 8 S S E lt gz gt 2 o Z z Q a Accessory Ignition Red T yig D G
18. ch refer to the Installation After turning the system off a slight ghost of the image will remain temporarily This is an effect peculiar to LCD technology and is normal Under cold temperature conditions the screen may lose contrast temporarily After a short warm up period it will return to normal Closing the Monitor Display NOTE The TMX R705 is a precision device With careful handling its performance can be maintained at a high level for a long time NOTE The TMX R705 is a precision device With careful handling its performance can be maintained at a high level for a long time 1 Press the OPEN CLOSE button of the main unit or press the POWER button press and hold the OPEN CLOSE button of the supplied remote control for at least 2 seconds The unit beeps 3 times and opens the monitor automatically Then the power of the monitor turns on NOTES Since this is an overhead monitor the display will be lowered when opened and raised when closed If the monitor touches an obstacle while it is being lowered the unit will stop immediately Should this occur remove the obstacle and press the OPEN CLOSE button again to close the monitor If you press the POWER button or the OPEN CLOSE button while the monitor is being opened or closed the monitor stops opening or closing and cannot be closed automatically In this case press the POWER button or the OPEN CLOSE button again to close the
19. e of the monitor off while you are listening with wireless headphones a big noise occurs through the headphones So be sure to take wireless headphones off your ears before you turn ACC or power source of the monitor off To the customers using wired headphones sold separately When you use the wired headphones with this unit it is recommended to use the ones of impedance of 24 45 Ben ohms Basic Operations Parts Names of the Overhead Monitor Remote Sensor Monitor Display OPEN CLOSE Button Dome Light Monitor Display Panel Wireless Headphone Transmitter Headphone Outputs Two output jacks mini phono plug are provided for wired headphones Output level is adjusted using the Volume UP DN buttons on the remote control NOTE Plugging a headphone into either jack will mute the Variable Audio Output RESET Switch Immediately after installing or applying power to the unit it should be initialized Using a pencil or other pointed object press this RESET switch to complete the initialization procedure Aen POWER OPEN CLOSE Opening the Monitor Display An SPST Single Pole Single Throw switch sold separately can be added to simplify this procedure Then you can simply place it in the OFF position when you leave the vehicle Turn the SPST switch back ON before using the TMX R705 For connecting the SPST swit
20. enter normal image d d e IEEE Gh e MODE 1 WIDE Stretches the normal image evenly in a horizontal direction so that it is displayed on the entire screen Stretches the normal image evenly in a horizontal direction so that it is displayed on the entire screen The stretching ratio increases the closer to the left or right edge of the screen MODE 3 CINEMA Stretches the normal image horizontally and vertically The top and bottom of the screen is cut slightly to adapt it to a cinema size image with a proportion of 16 9 DET Other Useful Features Adjusting Brightness of Picture 1 Press the SETUP button 2 Press the V or A button within 10 seconds and select BRIGHT 3 Press the lt or gt button within 10 seconds to adjust the brightness SET UP AUX1 BRIGHT COLOR TINT 4 Press the SETUP button to finish adjustments Adjusting Color Density of Picture 1 Press the SETUP button 2 Press the V or A button within 10 seconds and select COLOR 3 Press the lt or button within 10 seconds to adjust the color density SET UP AUX1 BRIGHT COLOR TINT 4 Press the SETUP button to finish adjustments BEN Adjusting Tint of Picture 1 Press the SETUP button 2 Press the V or A button within 10 seconds and select TINT 3 Press the lt
21. es ou indirects Dans ce Cas les limites et les exclusions de la garantie peuvent ne pas s appliquer vous CLAUSE APPLICABLE AU CANADA SEULEMENT Pour que la garantie soit valable il faut qu un centre d installation autoris ait install le syst me audio pour l auto dans votre v hicule et qu il ait ensuite appos son cachet sur la garantie NUM ROS D APPEL DU SERVIC E LA CLIENTELE Si vous avez besoin de nos services veuillez appeler le centre de service autoris Alpine le plus proche U S A CANADA 1 800 ALPINE 1 1 800 257 4631 1 800 ALPINE 1 1 800 257 4631 Alpine lectronique de L Am rique Inc 19145 Gramercy Place Torrance California 90501 U S A Alpine Electronique du Canada Inc Suite 208 7300 Warden Ave Markham Ontario L3R 9Z6 Canada LIMITED WARRANTY ALPINE ELECTRONICS OF AMERICA INC AND ALPINE OF CANADA INC Alpine are dedicated to quality craftsmanship and are pleased to offer this Warranty We suggest that you read it thoroughly Should you have any questions please contact your Dealer or Alpine at one of the telephone numbers listed below PRODUCTS COVERED This Warranty covers Car Audio Visual Products and Related Accessories the product Products purchased in the Canada are covered only in the Canada Products purchased in the U S A are covered only in the U S A LENGTH OF WARRANTY This Warranty is in effect for one year from the date of the firs
22. from the battery may cause fire or personal injury N PRECAUTIONS Temperature Be sure the temperature inside the vehicle is between 45 C 113 F and 0 C 432 F before turning your unit on Fuse Replacement When replacing the fuse s the replacement must be of the same amperage as shown on the fuse holder If the fuse s blows more than once carefully check all electrical connections for shorted circuitry Also have your vehicle s voltage regulator checked Maintenance If you have problems do not attempt to repair the unit yourself Return it to your Alpine dealer or the nearest Alpine Service Station for servicing Installation Location Make sure the TMX R705 will not be exposed to Direct sun and heat Excessive dust High humidity Excessive vibrations After turning the system off a slight ghost of the image will remain temporarily This is an effect peculiar to LCD technology and is normal Under cold temperature conditions the screen may lose contrast temporarily After a short warm up period it will return to normal Dome Light Bulb Replacement Precautions When replacing the dome light bulb replace with one having the specified 12V 5W capacity Use of a different capacity bulb may cause damage to the unit Note that damage under such circumstances will not be covered by the warranty To the customers using wireless headphones sold separately If you turn ACC or power sourc
23. function will instantly lower the volume level by 20 dB 1 Press the MUTE button to activate the MUTE mode The audio level will decrease by about 20 dB Pressing the MUTE button again will bring the audio back to its previous level Switching the Source 1 Press the SOURCE button Each press of the button will switch through the modes as follows AUXi gt Auxe NOTES e f nothing is connected to AUX 1 or AUX 2 raising the volume while these inputs are selected may result in excessive noise In addition to the Remote Control Source button each AUX input has its own wired select trigger This is called the External AV Select Pink Blue wire The External AV Select trigger is a pulsed signal Active Low 500ms or more If this input is remains low switching to other sources is not possible Switching sources using the Remote Control is still possible This is useful if you don t want an AV source to be interrupted Playing a video is a good example of this scenario This function is mainly used for connecting with other ALPINE products Switching Display Modes 1 Press the DISPLAY button or press and hold the SETUP button for at least 2 seconds Each press changes the display modes as follows MODE 1 VODE MODE 3 VODE 4 WIDE ZOOM CINEMA NORMAL MODE 4 NORMAL A normal television broadcasting 4 3 image is ma ES displayed in the c
24. in fire or electric shock DO NOT USE BOLTS OR NUTS IN THE BRAKE OR STEERING SYSTEMS TO MAKE GROUND CONNECTIONS Bolts or nuts used for the brake or steering systems or any other safety related system or tanks should NEVER be used for installations or ground connections Using such parts could disable control of the vehicle and cause fire etc KEEP SM ALL OBJECTS SUCH AS BATTERIES OUT OF THE REACH OF CHILDREN Swallowing them may result in serious injury If swallowed consult a physician immediately DO NOT INSTALL IN LOCATIONS WHICH MIGHT HINDER VEHICLE OPERATION SUCH AS THE STEERING WHEEL OR GEARSHIFT Doing so may obstruct forward vision or hamper movement etc and results in serious accident DO NOT INSTALL THE MONITOR NEAR THE PASSENGER SEAT AIR BAG If the unit is not installed correctly the air bag may not function correctly and when triggered the air bag may cause the monitor to spring upwards causing an accident and injuries A Caution HAVE THE WIRING AND INSTALLATION DONE BY EXPERTS The wiring and installation of this unit requires special technical skill and experience To ensure safety always contact the dealer where you purchased this product to have the work done USE SPECIFIED ACCESSORY PARTS AND INSTALL THEM SECURELY Be sure to use only the specified accessory parts Use of other than designated parts may damage this unit internally or may not securely install the unit in place This ma
25. o build up inside and may result in fire DO NOT WATCH VIDEO WHILE DRIVING Watching the video may distract the driver from looking ahead of the vehicle and cause an accident INSTALL THE PRODUCT CORRECTLY SO THAT THE DRIVER CANNOT WATCH TV VIDEO UNLESS THE VEHICLE IS STOPPED AND THE EM ERGENCY BRAKE IS APPLIED It is dangerous and illegal in many states for the driver to watch the TV Video while driving the vehicle The driver may be distracted from looking ahead and an accident could occur If the product is not installed correctly the driver will be able to watch the TV Video while driving the vehicle and may be distracted from looking ahead causing an accident The driver or other people could be severely injured N CAUTION This symbol means important instructions Failure to heed them can result in injury or material property damage HALT USE IMM EDIATELY IF A PROBLEM APPEARS Failure to do so may cause personal injury or damage to the product Return it to your authorized Alpine dealer or the nearest Alpine Service Center for repairing KEEP FINGERS AWAY WHILE THE MOTORIZED FRONT PANEL OR MOVING MONITOR IS IN MOTION Failure to do so may result in personal injury or damage to the product DO NOT MIX NEW BATTERIES WITH OLD BATTERIES INSERT WITH THE CORRECT BATTERY POLARITY When inserting the batteries be sure to observe proper polarity and as instructed Rupture or chemical leakage
26. of dust or dirt and any product that contains other contaminants including liquid or foreign objects HOW TO OBTAIN WARRANTY SERVICE CD You are responsible for delivery of the product to an Authorized Alpine Service Center or Alpine for repair and for payment of any initial shipping charges Alpine will at its option repair or replace the product with a new or reconditioned product without charge If the repairs are covered by the warranty and if the product was shipped to an Authorized Alpine Service Center or Alpine Alpine will pay the return shipping charges You should provide a detailed description of the problem s for which service is required 8 You must supply proof of your purchase of the product 4 You must package the product securely to avoid damage during shipment HOW WE LIMITIMPLIED WARRANTIES ANY IMPLIED WARRANTIES INCLUDING FITNESS FOR USE AND MERCHANTABILITY ARE LIMITED IN DURATION TO THE PERIOD OF THE EXPRESS WARRANTY SET FORTH ABOVE AND NO PERSON IS AUTHORIZED TO ASSUME FOR ALPINE ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF THE PRODUCT HOWWE EXCLUDE CERTAIN DAMAG ES ALPINE EXPRESSLY DISCLAIMS LIABILITY FOR INCIDENTAL AND CONSEQUENTIAL DAMAGES CAUSED BY THE PRODUCT THE TERM INCIDENTAL DAMAGES REFERS TO EXPENSES OF TRANSPORTING THE PRODUCT TO THE ALPINE SERVICE CENTER LOSS OF THE ORIGINAL PURCHASER S TIME LOSS OF THE USE OF THE PRODUCT BUS FARES CAR RENTALS OR OTHERS COST
27. t consumer purchase LIFETIME TAPE HEAD WARRANTY All Alpine Car Audio analog tape heads excluding Video tape heads are warranted for life against manufacturing defects causing failure WHO ISCOVERED This Warranty only covers the original purchaser of the product who must reside in the United States Puerto Rico or Canada WHATIS C OVERED This Warranty covers defects in materials or workmanship parts and labor in the product WHATIS NOTCOVERED This Warranty does not cover the following CD Damage occurring during shipment of the product to Alpine for repair claims must be presented to the carrier 2 Damage caused by accident abuse negligence misuse improper connections improper operation or failure to follow instructions contained in the Owner s manual 8 Damage caused by act of God including without limitation earthquake fire flood storms or other acts of nature 4 Any cost or expense related to the removal or reinstallation of the product Service performed by an unauthorized person company or association Any product which has the serial number defaced altered or removed Any product which has been adjusted altered or modified without Alpine s consent Any product not distributed by Alpine within the United States Puerto Rico or Canada 8 Any product not purchased from an Authorized Alpine Dealer Any product that has been determined to contain an excessive amount
28. ult your ALPINE dealer The TMX R705 uses female RCA type jacks for connection to other units e g amplifier having RCA connectors You may need an adaptor to connect other units If so please contact your authorized ALPINE dealer for assistance 14 IMPORTANT Please record the serial number of your unit in the space provided below and keep it as a permanent record The serial number plate is located on the bottom of the unit SERIAL NUMBER INSTALLATION DATE INSTALLATION TECHNICIAN PLACE OF PURCHASE Mounting Instruction This Motorized Overhead Monitor requires a 12V DC power supply for the Monitor Display to open and close Please DO NOT OPEN and CLOSE BY HAND and handle it with care Please follow these steps carefully 1 Remove the transportation screw from the unit Transportation Screw 2 Connect the main power connector 8 pin connector as well as one of the AUX input mini DIN to RCA Interface connectors refer to Installation and Connections on page 16 Also refer to the same page showing 5m mini DIN Extension Cable to AUX IN 1 connector for further details Make the proper Battery ACC ignition and Ground connections to make the unit operational 3 1 Turn the unit upside down With both hands hold the edges of this unit so as not to interfere with the opening and closing the monitor Open the monitor according to the following procedure Two persons m
29. y line of the vehicle This triggers main power to turn the unit on Although both DIN cables have this wire only one of them should be connected to the IGN ACC line 2 GND Black This is the shield GND It should connect to the vehicle s chassis for reducing any noise 3 External AV Select Pink Blue External AV Select forces the TMX R705 to switch to the A V input sending the AV Select trigger IR Remote Out White Brown The Remote Out wire connects to any ALPINE Mobile Video product which has an external remote input function For example products such as a DVD VCR and TV Tuner 5 AV RCA Connector Video Audio R Audio L These RCA type connectors connect to any video source This connector is used as an A V input for the TMX R705 however it may also be used as an output for other units Remote Control Lead White Brown D RCA Extension Cable Included with DVD changer RCA Extension Cable Sold Separately Ai NET Cable Included with DVD changer 17 u GARANTIE LIMIT E Fid les leur engagement de ne fournir que des produits de qualit ALPINE ELECTRONIQUE DE L AMERIQUE INC et ALPINE ELECTRONIQUE DU CANADA INC Alpine sont heureuses de vous offrir cette garantie Nous vous sugg rons de le lire attentivement et en entier Si vous avez la moindre question veuillez contacter l un de nos concessionnaires ou appeler directement Alpine au num ros Liste ci dessous PRODUITS COUVERTPAR LA GARANTIE
30. y cause parts to become loose resulting in hazards or product failure ARRANGE THE WIRING SO IT IS NOT CRIMPED OR PINCHED BY A SHARP METAL EDGE Route the cables and wiring away from moving parts like the seat rails or sharp or pointed edges This will prevent crimping and damage to the wiring If wiring passes through a hole in metal use a rubber grommet to prevent the wire s insulation from being cut by the metal edge of the hole DO NOT INSTALL IN LOCATIONS WITH HIGH MOISTURE OR DUST Avoid installing the unit in locations with high incidence of moisture or dust Moisture or dust that penetrates into this unit may result in product failure 13 Installation and Connections Precautions Be sure to disconnect the cable from the battery post before installing your TMX R705 This will reduce any chance of damage to the unit in case of a short circuit Be sure to connect the color coded leads according to the diagram Incorrect connections may cause the unit to malfunction or damage the vehicle s electrical system When making connections to the car s electrical system be aware of the factory installed components e g on board computer Do not tap into these leads to provide power for this unit When connecting the TMX R705 to the fuse box make sure the fuse for the intended circuit of the TMX R705 has the appropriate amperage Failure to do so may result in damage to the unit and or the vehicle When in doubt cons
31. z emballer soigneusement le produit pour viter tout dommage durant son transport LIMITATION DES GARANTIES TACITES LA DUR E DE TOUTES LES GARANTIES TACITES Y COMPRIS LA GARANTIE D ADAPTATION A L UTILISATION ET LA GARANTIE DE QUALIT LOYALE ET MARCHANDE EST LIMIT E CELLE DE LA GARANTIE EXPRESSE D TERMIN E CI DESSUS PERSONNE N EST AUTORIS ENGAGER AUTREMENT LA RESPONSABILIT D ALPINE EN VERTU DE LA VENTE D UN PRODUIT EXCLUSIONS DE LA GARANTIE ALPINE STIPULE EXPRESS MENT QU ELLE N EST PAS RESPONSABLE DES DOMMAGES DOMMAGES INT R TS ET DOMMAGES INDIRECTS PROVOQU S PAR LE PRODUIT LES DOMMAGES DOMMAGES INT R TS SONT LES FRAIS DE TRANSPORT DU PRODUIT VERS UN CENTRE DE SERVICE ALPINE LA PERTE DE TEMPS DE L ACHETEUR ORIGINAL LA PERTE D UTILISATION DU PRODUIT LES BILLETS D AUTOBUS LA LOCATION DE VOITURES ET TOUS LES AUTRES FRAIS LI S LA GARDE DU PRODUIT LES DOMMAGES INDIRECTS SONT LES FRAIS DE R PARATION OU DE REMPLACEMENT D AUTRES BIENS ENDOMMAG S SUITE AU MAUVAIS FONCTIONNEMENT DU PRODUIT LES RECOURS PR VUS PAR LES PR SENTES EXCLUENT ET REMPLACENT TOUTE AUTRE FORME DE RECOURS LIEN ENTRE LA GARANTIE ET LA LOI La garantie vous donne des droits sp cifiques mais vous pouvez aussi jouir d autres droits qui varient d un tat ou d une province l autre En outre certains tats et certaines provinces interdisent de limiter la dur e des garanties tacites ou d exclure les dommages accessoir
Download Pdf Manuals
Related Search