Avermedia NC100W Network Camera
Contents
1. Current Rate 0 KBps Current Rate 671 KBps Max Rate O KBps Max Rate 684 KBps Min Rate 0 KBps Min Rate 645 KBps Average Rate 0 KBps Average Rate 670 KBps Test Period 5 M Seconds Test Period 15 Seconds Test Exit Exit Press Test Test result H Exit Press this button to exit NetCam Manager Setting Login NetCam Configuration System Configuration Network Configuration Network Status Camera Configuration Auto eMail Configuration Login NetCam Configuration lg httpv192 166 1 1login html 1 Enter the login address of your camera in the address field of your browser 2 The default password of the camera is password If the default password is not changed you can simply click on Login to login NetCam Configuration To change password please refer to page 25 pom Login System Configuration System Information The System Information screen displays the current status of the camera on the Network e MAC address the MAC address of your camera s built in network card This item cannot be changed IP address the camera s IP address F W version the camera s firmware version HTTP Port the port number configured to receive data packets from the camera The default HTTP port number is 80 If you configure a different port number you must specify the port number in the browser ex 192 168 1 1 8080 where 8080 is the port number An alternative way is to configure2. 8 RX RX stands for reception 9 NAPT Network Address Port Translation NAPT is a method by which many network addresses and their TCP UDP ports are translated into a single network address and its TCP UDP ports Troubleshooting Q1 A1 Q2 A2 Q3 A3 How do I restore the camera to the default setting while the RDY LED is flashing yellow light Step 1 Press and hold down the reset button Step 2 Plug in the AC DC adapter Step 3 Release the reset button immediately when the RDY LED light changes into orange light Camera will soon be reset How do I recover device while RDY LED indicates yellow light Follow the steps to restore firmware amp configuration Step 1 Press and hold the reset button Step 2 Plug in the AC DC adapter Step 3 When you see the RDY LED indicates steady orange light don t release the reset button Release the reset button after the RDY LED light has changed into flashing orange light The camera will then start restoring firmware How can I access my NetCam if my NetCam is connected to internet via an IP sharing router Please configure NetCam s IP address to router s DMZ item or configure router s NAPT table to redirect HTTP packet to NetCam s IP address For example IP sharing router s network address is 192 168 1 x and NetCam s IP address is 192 168 1 123 You can directly configure router s DMZ item to 192 168 1 123 Or set router to forward IP packet with po
3. provided the correct password is entered http 192 168 1 1Aogin html Access the Login page on Internet Explorer However it may be possible that your PC and camera are using IPs that are considered to be in different segments even though they are actually in the same network segment If this happens pressing this button will popup a prompting message asking if you really want to configure the camera settings If you select Yes the following dialogue window will appear press After entering the correct password and pressing OK a setup window will popup as the following Password NetCam Manager User Interface NetCam Manager User Interface continued MIP Address f Via Static Assigned See wo fo Netmask 2s 25 2s 0 From DHCP Server DNS Server C Via Static Assigned From DHCP Server Change settings in this window You can then make changes and press OK to apply these changes to the camera For more information about these settings please refer to the Setting chapter The default Login password is password If the default password is not changed you can simply press OK to enter the setup window LZ Test Press this button to test the throughput readings The Login password is required to access the throughput test function aswa Eo xj Password ha Enter password and Lox ea press OK Throughput Test woughput Test
4. 1 Make sure that your PC has an e mail program installed before using these functions 2 The maximum recording time for Video Mail is 10 seconds Taking Pictures and Recording AVI Movies Camera Recorder Options 3 gt F Auto save video into separate files by interval 1 Click on 4 2 Press the button and specify a folder and file name to save the file 3 Check this box if you want to auto f you choose to auto save video clips you can specify the time interval save video clips between intervals For example a 10 in the minutes field indicates video clips will beautomatically saved tohard disk every 10 minutes The 4 Check this box if you don t want the file name will be automatically rendered file size to exceed 640MB Zoom Zoom x 1 is the default Viewer setting Choose Zoom x 2 or Zoom x 4 if you need to view the objects in detail NetCam Manager User Interface NetCam Manager User Interface Version 1 4 r f ae NetCam Manager IPAddress__ HostName MAC Address 00 0A4 94 00 A1 19 4s WD h Exit Ei Test Setup Scan There are four buttons on the screen Q gt Scan Press this button to scan all cameras in the same network segment 20 Setup Normally pressing this button will launch Internet Explorer and lead you to the Login page which will then lead you to the NetCam Configuration page
5. AVerMediae NC100 Digital Network Camera Series User Manual This devicecomplies with Part150fFCCrules Operation is subjecttothefollowing conditions 1 This devicemaynotcauseharmfulinterference and 2 This devicemustaccept any interference that may causeundesired operation 1 Do not drop puncture or disassemble the camera 2 Avoid all contact with water Dry hands before using 3 Do not expose the camera to high temperature or leave it in direct sunlight 4 Avoid pressing hard on the camera body Use only the AC adaptor supplied by the manufacturer Getting Started 3 NetCam Manager User Interface 20 Package Contents 4 Settin g 29 Parts Description 5 aa Login NetCam Configuration 23 Positioning the Camera 7 System Configuration 24 Installation 8 System Information Hardware Installation 9 Change Password Wired Connection NC100 Upgrade F W Firmware Wireless Connection NC100W Network Configuration 26 Connecting DI DO Device System IP Software Installation 12 WLAN Installing the NetCam Manager Network Statis 29 Configuring the Camera 13 Wired Link Information Using Your Camera s WLAN link Inf ftiatign for NC100W Taking pictures and Recording AVI Movies 17 E Eaten ai Snapshot Video Configuration Video Mail Digital Output Gamcorder Auto eMail Configuration 33 Zoom Auto eMail Configuration 2 Getting Started m Package Contents m Parts Description m Positioning the
6. Camera Package Contents 12V AC DC Adapter Driver CD Mounting Kit ee Eachpackage only contains one model Parts Description Front View Antenna only available for NC100W The antenna is used to communicate with wireless devices RDY ERR LED Ready Error LED s Flashing green boot up and self test Steady green power on and ready Flashing yellow auto email or configuration error Steady yellow firmware error l Lens the camera lens Spacer Ethernet WLAN LED Flashing green indicating Ethernet TX RX event NC 00 W Steady green Ethernet connection indicator Flashing yellow the camera is searching for a wireless AP Access Point device Steady yellow wireless connection indicator Parts Description R ear V j ew Ethernet Port this port is for connecting the Ethernet RJ45 cable Ethernet Port DC Power Jack the connector for DC power adaptor DI DO Pins the digital input digital output pins Please refer to the Installation chapter for more information a Reset puiton Reset Button press and hold this button to restore the DI DO Pins default settings or the factory firmware For more information please refer to the Troubleshooting section Stem Socket this socket is for connecting the mounting stem Stem Socket Positioning the Camera J Connecting the Camera to Mounting Stem Align the stem with the camera and p
7. Viewer for the first time you will see this warning message Press Yes to install the software This is required for the Viewer s operation Taking Pictures and Recording AVI Movies NetCam Viewer displays real time video stream captured by the camera With NetCam Viewer you can take snapshots or record video clips and e mail these files to your friends or you can save video clips in your hard disk To prevent anyone from directly accessing the Viewer you can set up a Guest Password Refer to the Setting chapter for more information You can e mail the picture or video clip to your friends Taking one single picture Recording a 10 second V NN AVI Movie Snapshot derei Video Maile wus Camera Recorder A Recording AVI Movies for longer periods The file will be saved in your local hard disk NetCam Viewer Taking Pictures and Recording AVI Movies Snapshot 1 Click on ish 2 The e mail program will be automatically started and the recorded BMP file is ready to be sent as an attachment You can then key in an e mail address to send the mail Video Mail 1 Click on 2 The camera starts to record a video clip Click on the icon again to stop recording 3 The e mail program will be automatically started and the recorded video clip is ready to be sent as an attachment You can then key in an e mail address to send the mail E
8. al Output Trigger by Digital Input specify that the digital output signal is triggered upon receiving the digital input signal You can further specify the duration of effective time in the blank field On manually turn on the digital output signal You can further specify the duration of effective time in the blank field Off manually disable the digital output feature NetCam Configuration Camera Configuration gt gt Video Configuration EC gt gt Digital Output Trigger by Digital Input duration time fo sec range 1 43200 sec O endless Auto eMail Configuration CON ie ai Configuration duration time i sec range 1 43200 sec 0 endless Network Configuration C OFF Network Status oR gt gt Wired Link Information System Configuration gt gt Change Password p gt Upgrade FW gt gt System Information Auto eMail Configuration Auto eMail Configuration As long as recipient s e mail settings are set up in Auto eMail Configuration you can send e mails with still pictures attached to the selected recipients The captured image will be in JPEG format 1 Key in Sender s Name Sender s Mail address and Email Subject 2 Key in e mail addresses for one or more recipients 3 Click on Select All or select recipients manually 4 Click on OK to complete Auto eMail Configuration 5 Every time the camera receives a DI Digital Input signal this Auto eMail will be s
9. am Click Cancel to quit Setup and close any programs you have running Click Next to continue with the Setup program WARNING This program is protected by copyright law and intemational treaties Unauthorized reproduction or distibution of this program or any portion of it map result in severe civil and criminal penalties and will be prosecuted to the maximum extent possible under law Cancel 4 Check Yes and click on Next License Agreement Please read the following license agreement carefully Please closely read the following license agreement Do you accept all the terms of the following license agreement Copyright c 1999 2002 Politecnico di Torino AIl rights reserved Redistribution and use in source and binary forms with or without modification are permitted provided that 1 source code distributions retain the above copyright notice and this paragraph in its entirety 2 distibutions including binary code include the above copyright notice and this paragraph in its entirety in the documentation or other materials provided with the distribution 3 all advertising materials mentioning features or use of this software display the folowing acknowledgement This product includes software developed by the Politecnico di Torino and its I Yes agree with all the terms of this license agreement lt Back ueo Cancel Ghost Installer Wizard 5 Click
10. ciated devices must be configured to use the same channel otherwise the connection will fail Channel number ranges from 1 to 14 Due to different regulations applicable channels differ in different areas See the following table for reference Channel 1 11 America Channel 1 14 Japan Channel 1 13 Europe most areas Channel 10 11 Spain Channel 10 13 France Encryption WEP Key Two levels of encryption methods are available 64bits and 128bits The 128bits method provides more protection while the 64bits standard is more widely supported After specifying the encryption method you can choose either Alohanumeric mode or Hexadecimal mode to enter the encryption key Note that the WEP key of camera and AP must match or the connection will fail The length of key varies according to the encryption mode and method as the following table shows Alphanumeric mode Hexadecimal mode 64 128 64 128 5 letters 13 letters 10 letters 26 letters WEP key index After enabling WEP encryption you must set this index value to match that of your Access Point AP otherwise the connection cannot be established Network Status Wired Link Information Port the port number configured to receive data NetCam Configuration packets for the camera The default HTTP port number is 80 e IP the camera s IP address PORT 80 MAC the MAC address of the came
11. ent with a still picture attached Auto e Mail does not send video clips NetCam Configuration Camera Configuration Sender s Name gt gt Video Configuration Sender s Email Address gt Digital Output Email Subject o g Auto eMail Configuration Network Configuration Network Status gt gt Wired Link Information System Configuration gt gt Change Password gt gt Upgrade FAW gt gt System Information Glossary 1 IP Address IP address is an address which is used to locate a network device on TCP IP network 2 DHCP Dynamic Host Configuration Protocol DHCP provides a framework for passing configuration information to hosts on a TCP IP network 3 DNS Server gt The Domain Name System is a distributed database that is used by TCP IP applications to map between host names and IP addresses and to provide electronic mail routing information 4 MAC Address MAC Media Access Control address is a unique hardware number on network It is used by the Media Access Control sub layer of Data Link Layer of communication protocol 5 HTTP The Hypertext Transfer Protocol HTTP is an application level protocol with the lightness and speed necessary for distributed collaborative hypermedia information system 6 ESSID ESSID stands for Extended Service Set Identifier It is used to identify wireless LAN groups rial 4 TX stands for transmission
12. era and AP device Clear button press this button to reset the counting of Total Tx Packets and Total Rx Packets Camera Configuration Audio Not available yet Video QVGA 320x240 VGA with lower resolution VGA 640x480 this is the default setting Mixed 320x320 or 160x120 If you select this option the PC display resolution is 320x320 while on other devices with smaller screens such as PDA or cell phones the display resolution will become 160x120 Frame Rate determines the time length to produce one frame You can increase the time length if the network is congested Video Format NTSC is for America while PAL is for Pan Europen areas Guest assword determines whether a regular user Needs to enter password before accessing the NetCam Viewer page NetCam configuration Network Status gt gt Wired Link Information gt gt WLAN Link Information System Configuration gt gt Change Password gt gt Upgrade FAW p gt System Information gt gt Reset System Video C QVGA 20 240 VGA 640x480 C Mixed 320x240 or 160x120 Frame Speed C 0 5sec 1sec C2sec Auto Video Format NTSC C PAL Guest Password C Enable Disable Password Confirm OR Warning Click OK button will save the data into the NetCam configuration If the saving is failed all configurations will be restored to the factory one at the next time reboot Camera Configuration Digit
13. ge their host manes to distinguish them Please refer to the Setting chapter for more information sc Windows Update gt Eo Accessories A ACO Systems A Acrobat Reader 5 0 A Internet Explorer al Outlook Express Aia NetCam Manager Yvy k S Documents Eh Settings P W Search X BF Help p Uninstall NetCam Manager pa Runs ap Shut Down Asm deng L Host Name i Robert NETCAM Sarah Jennifer Press this button to scan Configuring the Camera 2 Locating the camera on the Internet To locate the camera on the Internet you need to know the IP address of the camera Launch Internet Explorer and enter the IP address of your camera and you can use the camera as if it is in the same network segment Ping a specified IP Address to verify accessibility You can use PING Packet Internet Groper utility to check whether a specified IP address is accessible by sending a packet to the specified IP address 1 Start a Command prompt 2 Type ping IP address 3 Check the reply messages to determine whether the IP address is reachable f jCommand Prompt Microsoft Windows 298989 Version 5 66 21951 1 lt C gt Copyright 1985 1999 Microsoft Corp C oN gt ping 192 168 1 1 Pinging 192 168 1 1 with 32 bytes of data from 192 168 1 from 192 168 1 from 192 168 1 from 192 168 1 i bytes 32 time lt i ms TIL 64 i bytes 32 time lt i ms ITL 64 i bytes 32 time l
14. gt gt LOGOUT gt gt Video Viewer Camera Configuration gt gt Video Configuration Auto eMail Configuration gt gt Auto eMail Configuration Network Configuration Browse gt gt System IP gt gt WLAN Network Status gt gt Wired Link Information gt gt WLAN Link Information System Configuration Network Configuration System IP By default the camera is set to receive any IP address assigned by the DHCP server in the same network segment If you want to assign a static IP to the camera make sure that the IP is available every time the camera is powered on To configure a static IP address click on the item Via Static Assigned and then input the IP address subnet mask gateway and DNS server The following is an example of the settings IP address 192 168 1 1 Netmask 255 255 255 0 Gateway 192 168 1 254 DNS server 192 168 1 254 Note that the example may not be suitable for your actual condition You should consult an expert before making any change to these settings NetCam Configuration Network Status gt gt Wired Link Information gt gt WLAN Link Information System Configuration gt gt Change Password gt gt Upgrade FAW gt gt System Information IP Address Via Static Assigned Address SD flee ff fT Netmask SPS Ff Gateway fT flor fT E C From DHCP Server DNS Server Via Static Assigned Address Df ff fe Fro
15. lace it into the stem socket Screw mounting stem to the camera Mounting Kit Step 2 Installation E Hardware Installation m Software Installation m Configuring the Camera Hardware Installation E Connecting the Camera to a Network Wired Connection NC100 NC100W CH 1 Connect to Ethernet port Connect the RJ 45 cable to the Ethernet port on your camera then connect the ea other end of the cable to a hub or switch 2 Power 2 Connect to the AC power adaptor Connect the AC DC oe power adapter to a power outlet and to the camera E 3 Check the Indicator status Please wait for about 1 minute until flashing LED1 becomes steady green me ELaeh Elacmlarieliricele Wireless Connection NC100W 1 Connect to the AC power adaptor Connect the AC DC power adaptor to a power outlet and to the camera 2 Check the Indicator status Please wait for about 1 minute until flashing LED1 becomes steady green ae Wireless connection may require an Access Point AP device Please refer to the AP manual for more information on AP settings me ELaeh Elacmlarielricele J Connecting DI DO Device The DI DO feature allows you to connect the camera to various kinds of devices and to extend the utility of the camera There are 4 pins in total Pint and 2 form a digital input current loop Its maximum sustainable current is 50mA Maximum voltage is DC 15V Normally R1 i
16. m DHCP Server ox You can assign a static DNS server address even though the camera is set to receive IP address from a DHCP server Network Configuration WLAN For NC100W Mode Infrastructure In this mode the camera will try to LOGOUT gt gt Video Viewer communicate with an Access Point AP device Mode kiasia x Video Configurati Ad hoc In this mode the camera will try to establish a ee ae esso fay ooo Channel fl Encryption WEP Disatie gt ra WEP key index Ez peer to peer connection with another wireless device pap into Meet ony e Network Configuration gt You can choose a proper mode that suits your environment best _ n C Alphanumeric Hexadecimal ESSID This is the Network Name used to distinguish gt gt Wired Link Information WEP Key one network group from another This setting is case contin sensitive and it should match the ESSID of your target gt gt Change Password gt gt Upgrade FAW device or the connection will not be established The se syemiintormaton default setting Any enables the camera to search all possible targets to make a connection It is advised that Ee These settings are only for wireless connection you keep the default setting under most circumstances purposes Network Configuration WLAN continued e Channel This setting can only be changed in Ad hoc mode In peer to peer connection two asso
17. on Next 3 0 alpha 4 setup xj Readme Information Please read the following information about the WinPcap 3 0 alpha 4 carefully Important information about WinPcap 3 0 alpha 4 If an old version of WinPcap was already present on the system itis strongly recommended to reboot the system Please visit the WinPcap home page hita winpcap politait for information and updates car 6 Click on OK to finish the installation Installation Complete The Installation Wizard has successfully installed WinPcap 3 0 alpha 4 WinPcap 3 0 alpha 4 has been successfully installed Press the OK button to exit Setup program Configuring the Camera UltraEdit 32 1 Using NetCam Manager to locate the camera in the same LAN segment By default NC100W will accept the IP address assigned by a DHCP server If no DHCP server is present in the network segment NC100W will automatically set its IP address to 192 168 1 x x ranges from 1 to 254 with subnet mask 255 255 255 0 You can launch NetCam Manager to locate all cameras within your LAN segment To Launch NetCam Manager Click on the Start menu and go to Programs Then browse to the folder named NetCam Manager and run the program After the main screen appears the program will scan automatically or you can manually click on Qo to scan cameras in the same LAN segment If two or more cameras are using the same host name you can chan
18. ra s built in l 192 1684 t k d MAC 90 00 12 34 00 01 ue man om DNS 192 168 1 254 DNS Domain Name Service Server the IP tien i address of DNS server Total TX Packets 1607 Total RX Packets 1207 e Link Status displays the Ethernet link status up or Clear down z System Configuration gt gt Change Password e Total Tx Packets the amount of transmitted packets b gt Upgrade FAW Total Rx Packets the amount of received packets pae men e Clear button press this button to reset the counting of Total Tx Packets and Total Rx Packets Network Status WLAN Link Information for NC100W Port the port number configured to receive data packets for the camera The default HTTP port number is 80 NetCam Configuration PORT 80 IP the camera s IP address Ip 10 0 1 249 MAC the MAC address of the camera s network card ick ES A PEM T DNS 10 0 1 5 DNS Server the IP address of DNS server nese e e Link Status displays the wireless link status up or E ltd down CHANNEL 3 Total TX Packets 18314 ESSID current ESSID setting Total RX Packets 14273 e CHANNEL the channel currently used for gt WLAN Link Information Link Stenith EN Co transmission System Configuration Clear gt Change Password Total Tx Packets the amount of transmitted packets b gt Upgrade EW Total Rx Packets the amount of received packets EE e Link Strength indicates the link strength between the cam
19. rt 80 to 192 168 1 123 in NAPT table Troubleshooting Q4 A4 Q5 A5 Q6 A6 Q7 A7 Q8 A8 Q9 A9 No image shows while accessing NetCam Viewer The web page hasn t passed Windows Logo testing Please go to the Internet Explorer and change all settings to default settings Is there any limitation on the number of administrators Only one administrator is allowed Is there any limitation on the number of NetCam Viewer Maximun guests and 1 administrator are allowed to connect at the same time Recipients can t receive mails sent by the camera The mail server may be temporarily down or busy Please try to send the mail again later would like to configure a static DNS IP how can I obtain the information of my local DNS server Please ask your local ISP Internet Service Provider for assistance The NetCam Viewer display is blank Please check the security level of your browser If it is set to High lower the security level to solve this problem
20. s 10K ohms Pin 3 and 4 form a digital output current loop which is controlled by firmware You can program the behavior of DO signal through firmware settings refer to the Setting chapter for more information Its maximum sustainable current is 5 0mA Maximum voltage is DC 15V Note that a relay is necessary if the connected device requires AC power The following diagram illustrates an example of the connections The window sensor is a N C sensor In addition to window sensor you can also use a door sensor fs 1 DI DO fj Window Sensor C e Connecting these devices requires certain technical knowledge Please consult an expert before making changes to the settings Software Installation _ Installing the NetCam Manager 1 Insert the accessory CD into your CD ROM drive The software installation menu should open automatically 2 Click to start the NetCam Manager Installat a ion Follow the on screen instructions and a shareware program named WinPcap will be installed NetCam Manager r Manual 3 Click on Next Welcome to the Installation Wizard This wizard will guide you through the entire WinPcap 3 0 alpha 4 installation Welcome to the WinPcap 3 0 alpha 4 Setup program This program will install WinPcap 3 0 alpha 4 on your computer It is strongly recommended that you exit all Windows programs before running this Setup progr
21. t i ms TIL 64 i bytes 32 time 3ims TTL 64 Ping statistics for 192 168 1 1 Packets Sent 4 Received 4 Lost lt x loss gt Approximate round trip times in milli seconds ininum Bms Maximum Jims Average ms CiN gt m Note If any problem should occur during the PING process please check your network environment or ask an expert for help For detailed information on the configuration of the camera please refer to the Setting chapter E Using Your Camera E Taking Pictures and Recording AVI Movies mE NetCam Manager User Interface Configuring the Camera esearch HJ Favorites PMedia 4 EA 3 Entering the NetCam Viewer Fie Edit Yiew Favorites Tools Help There are two ways to enter the NetCam Viewer 1 Use NetCam Manager to scan the camera in the same network segment and double click on the title bar to enter the Viewer Security Warning 2 Start Microsoft Internet Explorer In the address Da you want to install and run http 10 0 6 50 netcam cab field input the IP address of your camera and press Enter to access the Viewer The publisher cannot be determined due to the problems i er below While running NetCam Manager double click on a specific s The test root has not been enabled as a trusted root camera title bar to enter the NetCam Viewer Version 1 4 Yes i More Info E you are entering the
22. your routers NAPT settings Please refer to the router s user manual for more information e Host Name host name can be renamed to distinguish different cameras NetCam Configuration Network Status gt gt Wired Link Information gt gt WLAN Link Information System Configuration 5 gt Change Password gt gt Upgrade FAW Eiee OOL MAC address IP address FAN version HTTP Port Host Name 90 00 12 34 00 01 192 168 1 1 1 02 07 System Configuration Change Password Here you can change the Login password Type in a new password and click on Change the old password will be replaced by the new password E The default Login password is password You should change this password to ensure security NetCam Configuration gt LOGOUT gt gt Video Viewer Camera Configuration gt gt Video Configuration Auto eMail Configuration Old Password gt gt Auto eMail Configuration N Network Configuration gt gt System IP New Password Confirm Password gt gt Wired Link Information gt gt WLAN Link Information Change Upgrade F W Firmware To upgrade the camera firmware please go to your dealer s website to download the latest firmware and save it in your hard disk Then click on the Browse button and locate the downloaded file Click on Update button and the camera s firmware will be upgraded NetCam Configuration
Download Pdf Manuals
Related Search