Garmin Fishfinder 400c Sonar System With Saltwater Transducer
Contents
1. owner s manual A GARMIN 2006 2007 Garmin Ltd or its subsidiaries Garmin International Inc Garmin Europe Ltd Garmin Corporation 1200 East 151 Street Liberty House No 68 Jangshu 2 Road Olathe Kansas 66062 USA Hounsdown Business Park Shijr Taipei County Taiwan Tel 913 397 8200 or 800 800 1020 Southampton Hampshire SO40 9RB UK Tel 886 2 2642 9199 Fax 913 397 8282 Tel 44 0 870 8501241 outside the UK Fax 886 2 2642 9099 0808 2380000 within the UK Fax 44 0 870 8501251 All rights reserved Except as expressly provided herein no part of this manual may be reproduced copied transmitted disseminated downloaded or stored in any storage medium for any purpose without the express prior written consent of Garmin Garmin hereby grants permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto provided that such electronic or printed copy of this manual must contain the complete text of this copyright notice and provided further that any unauthorized commercial distribution of this manual or any revision hereto 1s strictly prohibited Information in this document is subject to change without notice Garmin reserves the right to change or improve its products and to make changes in the content without obligation to notify any person or organization of such changes or improvements Visit the G2. Consider the following when you select an installation location INSTALLING THE FISHFINDER 400C To successfully operate your Fishfinder 400C you must properly install the fishfinder and all of its related parts Compare the contents of this package with the packing list on the box If any pieces are missing contact your Garmin dealer immediately Before you begin the installation Read and follow the instructions to install the unit Gather the appropriate fasteners and tools Verify that all cables can reach the unit mounting location and the transducer Wear safety goggles and a dust mask when drilling cutting or sanding If you experience difficulty installing the unit contact Garmin Product Support or contact a professional installer To install and use your fishfinder 1 2 3 4 5 Select a location for the fishfinder Mount the fishfinder Install the transducer Install the wiring harness Test the installation Fishfinder 400C Owner s Manual Provides optimal viewing as you operate your vessel Allows easy access to the unit s keypad Is strong enough to support the weight of the fishfinder and protect it from excessive vibration or shock Allows room for the routing and connection of the power data and transducer cables There should be at least a 3 inch 8 cm clearance behind the case DO NOT mount the unit in an area that is exposed to extreme temperature conditions NOTE The temper
3. iil Caring for the Fishfinder 400C csssssssesesecseeseeseeeeees iil WANO S as IV Important Information cccscssesesesseeseessesseesessseeseneeees IV Installing the Fishfinder 400C ee eesesseeessensseesseeeees 1 Step 1 Select a Location for the Fishfinder 000008 1 Step 2 Mount the Fishfinder c ccssessessessessesseeseeees 2 Step 3 Install the Transducer c cccsscesesseseeseeeseeeeeeees 4 Step 4 Install the Wiring Harness ccscssssssseseseseees 10 Step 5 Test the Installation cccsssessessseessessesseeseeeees 13 Basic Operation scascantectcecassensaentoaticcanstenicessansteterenseanseatee 15 Turning the Fishfinder 400C On or Off 15 Adjusting the Backlight Setting ccscssssssssesesees 15 Using Simulator Mode ccscssssssesscsecsesesssesseeseesenenes 15 Using the Fishfinder 400C Keypad ccscsssssseseseseneens 15 Understanding the Home Screen cscssssssseseecsneens 16 Understanding the Full Screen c cssssssssessesecsesensens 17 Understanding the Split Zoom Screen cccseseeeeeees 17 Understanding the Flasher Screen cssssseseeeeees 18 Understanding the Split Freq Screen 18 li Understanding the Numbers Screen cccsscseseseeees 19 Understanding the Temp Log SCreen cssssssesesesneens 19 Understanding the Configure Screen cssssssesesesnens 20 Customizing the Fishfinder 400
4. C esses 21 Seling Pl GNINS aeoiee aoee 21 Changing the Display Settings sscssssssesesnseeees 21 Changing the Sonar Settings ssssssesssssssesenseeees 22 Changing the System Settings ccsesssseseseeeeeees 23 Configuring Transducer Settings ccsssessseseseeees 23 Customizing Units of MeaSure s ssssssessssnsnnnnsnnsnnnnsnnnnsnnnnns 24 Advanced Settings acces ec tee eccentric 25 Resetting the Odometer ccssssssscscsssssseseeeneees 26 Setting the Temp Log Duration and Scale eee 26 PAPO GS INGUIN acca tinn r de cae AEE i 27 Specifications jac casccnscsanscciesstesnaniineasspinpanddenanenissanacianasvonsqnaunans 27 Optional ACCESSOLICS csccsscseecstssseessesseessesssesssensseeeees 27 Alarms and M SSag ssccsssscsesscseessessessnessesseessnsseneas 28 Limited Warranty siiscsstscessciaccasetsactssasenesexsadtevetwescnastenisarerteess 29 Declaration of Conformity DOC ssssssssssssssssssssnnnnsnnnnrnsnnnnns 30 Software License Agreement csssssssssssssseseesersesees 30 pe ES AA E E A E E 31 Fishfinder 400C Owner s Manual Product Registration Help us better support you by completing our online registration today Connect to our Web site at www garmin com registration Use this area to record the serial number 8 digit number located on the back of the Fishfinder 400C in case your Fishfinder 400C needs service Keep the original sales receip
5. HE FISHFINDER 400C Installing the Fishfinder 400C on the Mounting Bracket To mount the bracket assembly Li Using the swivel base as a template mark the location of the three holes that secure the bracket to the mounting surface Drill the mounting holes e f you secure the base with machine bolts drill three 5 32 5 mm holes at the locations you marked OR e f you secure the base with self tapping screws drill Starter holes at the locations you marked Do not make the starter holes deeper than half the screw length Secure the swivel base with three bolts or screws DO NOT OVERTIGHTEN Place the swivel mount bracket over the swivel base and secure it with the short knob Fishfinder 400C Owner s Manual To install the unit on the mounting bracket P Align the slot on the back of the fishfinder with the long mounting knob and slide the fishfinder into place If necessary adjust the long knob to spread the bracket arms apart Turn counter clockwise to widen the bracket arms and clockwise to tighten Adjust the fishfinder angle and tighten the long mounting knob until snug y _ 4 Rotate the swivel mount bracket by twisting it left or right The bracket clicks as you turn it Select a good viewing angle and then tighten all knobs Connect the power data and transducer cables to the back of the fishfinder making sure the locking rings are fully tightened on both connectors INSTALLI
6. NG THE FISHFINDER 400C Step 3 Install the Transducer Assembling the Transducer Proper transducer installation is key to getting the best performance To assemble the transducer from your fishfinder If the transducer lead is too short extension 1 Insert the rubber washer and plastic spacer into the cables are available from your Garmin dealer Coil and secure any transducer at the same time DO NOT lubricate the rubber excess cable washer ne ne nnn 2 Route the cable toward the back of the transducer Slide the CAUTION DO NOT cut the transducer lead or any part of transducer into the transducer mount the transducer cable because cutting the transducer cable voids 3 Place a5 mm flat washer on the 10 32 x 1 75 screw and The cabl t be spliced and ted t RUE Well ay ne ea AON OSEE ane COnnee ay insert the screw through the transducer mount spacer and existing Garmin or non Garmin transducer cables rubber washer The following pages contain tips and basic installation instructions 4 Place the remaining 5 mm flat washer on the exposed end for some popular transducers Detailed installation instructions are Install the 10 32 lock nut finger tight You can tighten the provided in the transducer kits Some transducers might have to be transducer further after installation on the boat installed by a professional marine installer Cable tie slot 4 Fishfinder 400C Owner s Manual INSTALLING THE FISHFINDER 400C Mounting th
7. NMEA Device GREEN CANet L WHITE CANet H Alarm Relay 100ma max coil current YELLOW Alarm Low Fishfinder 400C Wiring Harness Fishtinder 400C Owner s Manual 11 INSTALLING THE FISHFINDER 400C Connecting to a NMEA device You can connect the Fishfinder 400C to another piece of NMEA compatible electronic equipment such as a Garmin GPS Global Positioning System device If equipped with a capable transducer the Fishfinder 400C can send depth temperature and speed information Refer to the wiring diagrams on page 11 for connecting the Fishfinder 400C to NMEA compatible devices To install the wiring harness to a GPS or other NMEA device 1 Follow the voltage source installation steps see page 10 For Garmin units the ground Black wires serve as NMEA ground and must be attached together or on the same terminal Refer to the wiring diagram of your GPS unit for wire identification 2 Connect the Blue NMEA Out wire from the Fishfinder 400C to the NMEA In wire on the GPS NMEA unit s wiring harness 3 Turn on the Fishfinder 400C NMEA Output setting page 23 For Garmin GPS units set the communications interface to NMEA NMEA NMEA In NMEA Out or NMEA Interfacing with NMEA The Fishfinder 400C allows for NMEA 0183 Version 3 01 output with a compatible GPS or navigation device You must set NMEA Output On to send data page 23 12 The SDDBT SDDPT SDMTW SDVHW SDWPL sentences are sent i
8. The standard plastic transom mount transducer can also be mounted using this method If using a temperature sensing transducer the temperature shown reflects the hull temperature Fishfinder 400C Owner s Manual INSTALLING THE FISHFINDER 400C Selecting a Location for a Shoot Thru Hull Installation When installing a transducer the installation location must be the following To 1 Solid fiberglass without any air bubbles laminates fillers or dead air space In an area of clean non turbulent water at all speeds The location must not be over any strakes or behind any obstruction on the hull that would create turbulence NOTE Many modern hulls have a dedicated pocket for shoot thru hull transducer installation If you are unsure if your hull is equipped with a pre located pocket contact your hull manufacturer test the location Fabricate a test device from a section of PVC pipe or a can as shown in the following illustration Temporarily seal the test device to the hull with caulking or RTV sealer and fill with water or light mineral oil Place the transducer in the water pointed directly at the bottom and weight it down Set the unit for optimum performance If the sonar performance is significantly degraded another location must be tested Fishtinder 400C Owner s Manual RTV sealer N Weight the transducer to hold it in place SS PVC pipe ora can _Z Fill a pipe or can with w
9. armin Web site www garmin com for current updates and supplemental information concerning the use and operation of this and other Garmin products Garmin CANet See Thru and Ultrascroll are registered trademarks or trademarks of Garmin Ltd or its subsidiaries and may not be used without the express permission of Garmin March 2007 Part Number 190 00757 00 Rev C Printed in Taiwan INTRODUCTION INTRODUCTION Quick Links The Fishfinder 400C is a full featured color sonar that offers a choice Installing the Fishfinder 400C page 1 of display styles a dual beam or dual frequency option and more eae ae ee nee oi Mounting the Fishfinder 400C page 2 Fishfinder 400C Tips and Shortcuts BSP in gitte Dae O eee Press HOME from any screen to return to the Home screen Basic Operation page 15 Press MENU from any of the main screens to access Customizing the Fishfinder 400C page 21 advanced settings Changing the System Settings page 23 Press and release the D POWER key to adjust the display Customizing the Transducer Settings page 23 settings Advanced Settings page 25 Alarms and Messages page 28 Fishtinder 400C Owner s Manual i INTRODUCTIO Table of Contents SINFO GUIGHON weccetveicinauidsesnssousnireswcarenseerdeesvieaneenstavietaenel i Fishfinder 400C Tips and Shortcuts ccssssseesseeeens i Quick LINKS iit msniravneinicndiinnmnnenavenniudnnidnnisininnnvotintan i Product Regis EATON sonia
10. ater or a light mineral oil Hull surface Testing the Location To permanently install the transducer 1 Lightly sand the surface of the hull and face of the transducer with 400 grit wet or dry sandpaper Build a dam using strip caulk about 1 4 6 mm tall Pour about 1 8 3 mm of two part slow cure epoxy into the dam Place the transducer in the epoxy turning the transducer to work out any air bubbles Weight the transducer in place and allow it to cure for 24 hours INSTALLING THE FISHFINDER 400C Step 4 Install the Wiring Harness To install the wiring harness The Fishfinder 400C comes with a wiring harness that connects 1 Use a test light or voltmeter to determine the polarity of the the fishfinder to power and the transducer with one easy to remove voltage source connection and provides interface capabilities for connecting 2 Connect the Red or positive wire to the positive voltage ateral devices terminal If you use the boat s fuse block route the positive connection through the fuse as shown on the diagram The color code in the diagram see page 11 indicates the appropriate 3 Connect the Black or ground wire to the negative voltage harness connections The replacement fuse is a AGC 3AG 3 Amp terminal fuse If it is necessary to extend the power wires use 22 AWG wire 4 Install or check the 3 Amp fuse on the boat s fuse block or in DO NOT cut the transd
11. ature range for the Fishfinder 400C is 5 F to 131 F 15 C to 55 C Extended exposure to temperatures exceeding this range in storage or operating conditions may cause failure of the LCD screen This type of failure and related consequences are NOT covered by the manufacturer s limited warranty INSTALLING THE FISHFINDER 400C Step 2 Mount the Fishfinder You can mount your fishfinder in one of two ways Surface Mount mount the fishfinder onto a bracket included that attaches to the console or overhead Flush Mount use the optional flush mount kit to mount the fishfinder into a flat panel See the Appendix for more information Surface Mounting the Fishfinder The Fishfinder 400C s compact waterproof case is suitable for mounting in exposed locations or at the nav station The Fishfinder 400C comes with a tilt swivel mounting bracket that can be used for console or overhead mounting Mounting the Bracket Assembly Tools not included drill screwdriver Phillips or standard and one of the following Three 8 4 mm pan head machine bolts with matching nuts and washers and a 5 32 5 mm drill bit Three 8 pan head self tapping screws and a 1 16 drill bit for drilling starter holes Use a pan head machine bolt or self tapping screw to secure the swivel base If you use a screw with a countersunk head you risk damaging the mounting bracket Fishfinder 400C Owner s Manual INSTALLING T
12. e Transducer on a Trolling Motor 6 Route the 30 foot 9 m transducer cable using the supplied Dual Beam Transducers Only cable ties to secure the cable to the motor shaft You can fill the forward facing portion except the cable tie pocket of the To mount the transducer on a trolling motor transd t with sealant t id lating debris 1 Slide the large cable tie through the slot on the transducer BRM eect E A A iad mount with the ridges of the band facing up until equal lengths extend on both sides of the mount NOTE For cold water or heavy timber or debris areas a metal 4 5 worm gear clamp 1s recommended Cable tie 2 Position the mount gasket on the curved top of the transducer mount 3 Place the transducer assembly against the motor body of the trolling motor with the front of the transducer pointed away from the trolling motor propeller 4 Wrap the two ends of the cable tie around the motor body Place the pointed end of the cable tie through the fastener hole on the opposite end and pull it through until it is snug but not tight The cable tie clicks when you pull it 5 Position the transducer so that it is parallel with the bottom when in use and make sure the gasket is aligned properly Pull the cable tie end until tight Trim off the excess if necessary Tighten the 10 32 locking nut until it touches the mounting bracket and then tighten 1 4 turn more Do not overtighten Front of the transducer F
13. ersion The unit is waterproof to IEC Standard 60529 IPX7 It can withstand immersion in meter of water for 30 minutes Prolonged submersion can cause damage to the unit After submersion be certain to wipe and air dry the unit before reuse lil INTRODUCTION Failure to avoid the following potentially hazardous situations could result in an accident or collision resulting in death or serious injury e When navigating carefully compare information displayed on the unit to all available navigation sources including information from visual sightings and maps For safety always resolve any discrepancies or questions before continuing navigation WARNING This product its packaging and its components contain chemicals known to the State of California to cause cancer birth defects or reproductive harm This Notice is provided in accordance with California s Proposition 65 See www garmin com prop65 for more information LAMPS INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL STATE OR FEDERAL LAWS For more information go to www garmin com aboutGarmin environment disposal jsp Important Information The California Waste Recycling Act of 2003 requires the recycling of certain electronics For more information on the applicability to this product see www erecycle org IV Fishfinder 400C Owner s Manual INSTALLING THE FISHFINDER 400C Step 1 Select a Location for the Fishfinder
14. ishtinder 400C Owner s Manual J INSTALLING THE FISHFINDER 400C y y yya Mounting the Transducer on a Transom Mount the transducer cable Apply marine sealant to all screw threads to prevent water cover well above the j waterline from seeping into the transom Transducer should extend 1 8 below fiberglass hull or N lt 3 8 below aluminum hull IN A 4 Make sure that the transducer is below l water level when the boat is on plane an at high speed Do not mount the transducer directly in the path of the prop The transducer can cause Mount the transducer parallel with the bottom eon UCM Abin nagrada Me Boats performance and damage the prop Fishfinder 400C Owner s Manual INSTALLING THE FISHFINDER 400C Tool List not included drill 3 8 wrench or socket 5 32 and 1 8 drill bits masking tape 2 Phillips screwdriver and marine When selecting a transom mount location consider the following for optimal performance For your sonar to operate properly the transducer must be located in calm water DO NOT mount the transducer behind strakes rivet lines struts fittings water intake discharge ports eroding paint or anything that creates turbulence Mount the transducer as close to the center of the boat as possible DO NOT cut the transducer lead This voids your warranty DO NOT mount the
15. n NMEA 0183 Version 3 01 output from the Fishfinder 400C You can purchase complete information about National Marine Electronics Association NMEA format and sentences from NMEA Seven Riggs Avenue Severna Park MD 21146 USA www nmea org Installing the Fishfinder 400C to a Garmin CANet The Fishfinder 400C is a CANet compatible sonar device Using the CANet if applicable optimizes the performance of CANet compatible units allowing sonar information from the Fishfinder 400C to be shared with up to two CANet compatible Garmin GPS units A standard NMEA connection only allows depth temperature and speed information to be sent to a single GPS device whereas a CANet connection provides full sonar readings including Ultrascroll so you can view and control the same information on your compatible GPS unit s as you can on your Fishfinder 400C NOTE To use the Garmin CANet with your Fishfinder 400C you must obtain a CANet Kit Contact your Garmin dealer or visit www garmin com Fishfinder 400C Owner s Manual INSTALLING THE FISHFINDER 400C Step 5 Test the Installation To turn on your Fishfinder 400C for the first time press and hold the POWER key until the unit beeps and turns on Use the ROCKER and the SELECT key and follow the screens to configure your Fishfinder 400C A NOTE Although it is possible to perform some checks with the boat trailered the boat should be in the water to properly test the installation T
16. nut until it touches the mounting bracket and then tighten 1 4 turn more Do not overtighten Place the first cable clamp on the transducer cable approximately one third of the distance between the transducer and the top of the transom INSTALLING THE FISHFINDER 400C 6 Mark the location Using a 1 8 bit drill a pilot hole approximately 3 8 10 mm deep 7 Attach the cable clamp using a 4 x 12 mm screw Coat the screw with marine sealant before installation Repeat steps 5 and 6 using the other cable clamp 8 Route the transducer cable as needed to the fishfinder DO NOT CUT THE CABLE Avoid routing the cable with electrical wires or other sources of electrical interference Drill pilot holes here Align with the transom bottom The transducer should extend 1 8 below fiberglass hulls or 3 8 below aluminum hulls Vertical nsom Shoot Thru Hull Installation To avoid drilling a hole to mount a thru hull transducer a transducer can be secured with epoxy inside a boat shoot thru hull installation This type of installation can provide better noise reduction and allow you to use a higher Gain setting For a transducer to be mounted inside the hull shoot thru not thru hull the boat must be fiberglass with no core Contact your boat manufacturer if you are unsure Professional installation might be necessary Some transducers are specifically designed to be mounted inside a fiberglass hull
17. o configure your Fishfinder 400C for the first time Select a language Select a transducer Select units of Select a color type measure scheme Language 0 Transducer 0 punts OO Color Scheme eT ooo Dual Beam Metric Gere m C jnwleaa IKE FEGE Back The Home screen appears after you select your configuration options After 15 seconds of inactivity the fishfinder automatically switches to Full Screen A NOTE If the transducer is not detected a Transducer Disconnected Sonar Turned Off message appears Fishfinder 400C Owner s Manual 13 INSTALLING THE FISHFINDER 400C Because water 1s necessary to carry the sounder s sonar signal the 3 Ifthe signal strength improves while turning adjust the transducer must be in the water to work properly You cannot get a transducer so that it extends another 1 8 below the transom depth or distance reading when out of the water of the boat It might take several adjustments to eliminate the degradation When you place your boat in the water check for leaks around any screw holes that were added below the water line DO NOT leave your boat in the water for an extended period of time without checking for leaks 4 Ifthe signal does not improve you might have to move the transducer to a different location NOTE When adjusting the depth of the transducer make the adjustments in small increments Placing the transducer too To test the transom mount tran
18. sducer installation deep can adversely affect the boat s performance and put the 1 Begin testing the installation at a slow speed If the sonar transducer at greater risk of striking underwater objects appears to be working properly gradually increase the boat s speed while observing the sonar s operation If the sonar signal is suddenly lost or the bottom return is severely degraded note the speed at which this occurs 2 Return the boat to the speed at which the signal was lost Make moderate turns in both directions and see if the signal improves 14 Fishfinder 400C Owner s Manual
19. t or a photocopy in a safe place Serial Number Contact Garmin Contact Garmin if you have any questions while using your Fishfinder 400C In the USA contact Garmin Product Support by phone 913 397 8200 or 800 800 1020 Monday Friday 8 AM 5 PM Central Time or go to www garmin com support and click Product Support In Europe contact Garmin Europe Ltd at 44 0 870 8501241 outside the UK or 0808 2380000 within the UK Tell Us What You Think Tell us how you like this manual Fill out the Product Documentation Survey Go to www garmin com contactUs and click Product Documentation Survey Fishtinder 400C Owner s Manual INTRODUCTION Caring for the Fishfinder 400C The case is constructed of high quality materials and does not require user maintenance except cleaning Cleaning the Case Clean the unit s outer casing except for the screen using a cloth dampened with a mild detergent solution and then wipe dry Avoid chemical cleaners and solvents that may damage plastic components Cleaning the Screen The unit s lens is coated with a special anti reflective coating that is sensitive to skin oils waxes and abrasive cleaners Cleaners containing ammonia alcohol abrasives or anti grease detergents will harm the anti reflective coating It is important to clean the lens using an eyeglass lens cleaner that is specified as safe for anti reflective coatings and a clean lint free cloth Water Imm
20. transducer in locations where it might be jarred when launching hauling trailering or storing DO NOT mount the transducer in the path of the prop on single drive boats The transducer can cause cavitation that can degrade the boat s performance and damage the prop On twin drive boats mount the transducer between the drives if possible fittings water intake or discharge ports or anything that creates air bubbles or causes the water to become turbulent The transducer must be in clean non turbulent water for optimal performance Fishtinder 400C Owner s Manual NOTE DO NOT mount the transducer behind strakes struts sealant To mount the transducer on a transom k Position the transducer mount at the selected transom location Make sure the transducer is parallel with the water line Mark the center locations of each hole on the transducer mount Using a 5 32 bit drill the pilot holes approximately 1 25 mm deep at the marked locations To avoid drilling the holes too deep wrap a piece of tape around the bit at 1 from the point of the bit Apply marine sealant to the 5 x 30 mm screws Attach the transducer assembly to the transom using the 5 x 30 mm screws Adjust the transducer assembly to extend beyond the bottom of the transom approximately 1 8 3 mm on fiberglass hulls or 3 8 10 mm on aluminum hulls Adjust the transducer assembly to be aligned parallel with the water Tighten the 10 32 locking
21. ucer cable because this voids your warranty the in line holder If your boat has an electrical system you might be able to wire the 5 Align the notches on the cable plug and on the back of the fishfinder directly to an unused holder on your current fuse block If fishfinder Insert the cable into the connector and turn the you are using the boat s fuse block remove the in line fuse holder lock ring counter clockwise until it stops supplied with the fishfinder You can also wire the fishfinder directly to the battery 3 Amp fuse To 10 38 Volt boat supply CAUTION The Fishfinder 400C maximum input voltage is 35 2h Volts DC Do not exceed this voltage because this can damage Boat ground 7 z the Fishfinder 400C and void the warranty A H Oe mjo A NOTE During a typical installation use only the Red and Black ie wires The other wires do not have to be connected for normal q dil GHG B operation of the Fishfinder 400C unit For information on connecting gt N to a NMEA or CANet compatible device see page 12 ri aa To Fishfinder 400C Fuse block 10 Fishfinder 400C Owner s Manual INSTALLING THE FISHFINDER 400C B To Transducer PIN 8 Black Ground PIN 7 Yellow Alarm RED VDC PIN 13 Red DC Positive PIN 12 White CANet H PIN 16 Green CANet L PIN 18 Blue NMEA Out BLACK Ground aL DC Power Source BLUE NMEA Out RXD
Download Pdf Manuals
Related Search