Hoover WindTunnel Widepath U5397 Vacuum
Contents
1. Higher settings for very deep pile carpet where easier pushing effort is desired while maintaining good clean ing performance Note If the cleaner is difficult to push slide knob to the next higher setting Stair cleaning A stair cleaning handle has been designed for ease in using your cleaner on stairs With handle in operat ing position place fingers under edge of stair cleaning handle and guide cleaner with other hand on upper handle As an alternative you may use the hose and furniture nozzle for stair cleaning Clean from bottom to top When using cleaning tools the agitator will continue to rotate CAUTION To avoid personal injury or unnecessary wear to carpet and to prevent the cleaner from falling always place it at bottom of stairs Cleaning tools Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas The cleaner is ready for tool use when handle is in upright position CAUTION Agitator continues to rotate while cleaner handle is in upright position Avoid tipping cleaner or setting it on furniture fringed area rugs or carpeted stairs during tool use How to clean tools To clean the hose wipe off dirt with a cloth dampened in a mild detergent Rinse with a damp cloth Cleaning tools may be washed in warm water with a detergent Rinse and air dry before using Attach wand and tools When using cleaning tools cleaner handle should be in2. on front of handle Hold each nut in place while tightening each bolt securely with a Phillips screw driver STEP III Attach hose EJ Align end of hose with projec tions A over slots B in dirt duct Slide handle onto cleaner body LM Push bolts into holes on back of handle E Reposition bag door by fitting 7 tabs on bottom of door into opening Press top of door to snap securely shut Position cord on back of cleaner as shown and press cord into clip Note Hose must be connected as shown for all operations Slide hose into B and twist ime Lift hose tube cover C hose to lock it into place 10 Position hose over hose hook D and into hose tube E Continued gt 3 STEP IV Position tools Place smaller unridged end of Snap ends of dusting brush A wand into bottom of rack crevice tool B and furniture Snap wand into clip Repeat with nozzle C into clips as shown other wand Cleaner description 1 Handle 11 Furniture guard helps prevent 2 Cord hooks wrap cord around cleaner from marking furniture hooks for storage The top 12 Edge groomers hook can be rotated right or left 13 Embedded Dirt FINDER for easy cord release display 3 Hose 14 Dirt FINDER sensitivity switch 4 ON OFF switch located on left rear 15 Wands corner of cleaner body 16 Check bag indicator 5 Carrying handle
3. plate while turning agitator To maintain cleaning effectiveness replace agitator if brushes do not touch card What to buy Your cleaner requires either a 13 or 15 agitator When purchasing a new agitator ask for one of the following 13 HOOVER part No 48414057 15 HOOVER part No 48414017 How to replace Disconnect cleaner from electrical outlet Remove bottom plate belt and agitator following directions in The belt section beginning with Fig 39 Discard old agitator Continue following the directions in The belt section to reposition belt new agitator and bottom plate Clearing blockages Disconnect cleaner from electrical outlet Low suction or pick up may be due to a blockage in the system Refer to the following steps to check for blockages continuing with each step until the blockage is found 1 Check fullness of filter bag change if needed 47 2 Plug cleaner in and turn ON Check for suction at end of hose A a If there is suction continue with step 3 b If there is no suction check for blockage in hose and dirt tube as follows 1 Disconnect hose from dirt duct C by reversing procedure for Attach hose on p 3 Fig 8 and 9 2 Clear out hose 3 Look into C and remove blockage 3 Check connection at hose tube B remove any blockage 4 Turn cleaner OFF and unplug 5 Remove bottom plate belt and agitator see The belt section BE
4. the upright position Also turn cleaner OFF before disconnecting and connecting hose to hose tube A To use hose lift hose end as shown Select proper tool PAs A Dusting brush may be used for carved furniture table tops books lamps lighting fixtures venetian blinds baseboards shutters and registers B Furniture nozzle may be used for upholstered furniture draperies mattresses clothing automobile interiors and carpeted stairs Lower cover B onto hose tube When you are finished cleaning with the tools be sure to lift cover from hose tube and reposition hose end into tube C Crevice tool may be used in tight spaces corners and along edges in such places as dresser drawers upholstered furniture stairs and base boards D Wands are used to give extra length to your hose Use them with any of the above tools wt C D Attach tool or wand to the hose C by pushing it firmly into hose Attach second wand or tool to wand D by pushing it firmly onto the wand Twist wand or tool slightly to tighten or loosen the connection Maintenance Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure contin ued cleaning effectiveness The filter bag When to replace Check filter bag from time to time It is recommended that you change the filter bag when dirt reaches the dotted line If more dirt than this accumulates your cleane
5. 17 Final filter exhaust 6 Bag door 18 Dusting brush 7 Stair cleaning handle located on 19 Crevice tool lower edge of bag door 20 Furniture nozzle 8 Handle release lever step on 21 Hose hook lever to lower handle to operating or low positions some models only 9 Headlight 10 Nozzle control knob slide knob to correct setting for height of carpet being cleaned The assembled cleaner will look like the drawing above Operate cleaner only at voltage specified on data plate on bottom of cleaner How to use To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the plug in any way Handle positions The handle of your cleaner has three positions upright for storage and when using cleaning tools operat ing position for general operation on carpet and floors low for reaching under low furniture Step on handle release lever to lower handle Embedded Dirt FINDER feature some models only 19 With red and green lights A the Dirt FINDER system alerts the user to areas of carpet that may need more cleaning attention It is able to sense when larger amounts of dirt particles especially embedded di
6. A Look into opening D for blockages and remove 6 Remove agitator shield see Fig 42 and remove any loose debris which may have accumulated under it Thermal protector An internal thermal protector has been designed into your cleaner to protect it from overheating When the thermal protector activates the cleaner will stop running If this happens proceed as follows 1 Turn the cleaner OFF and disconnect it from the electrical outlet 2 Check secondary and final filters for dirt accumulation 3 Refer to Clearing blockages section 4 When cleaner is unplugged and motor cools for 30 minutes the thermal protector automatically resets and cleaning may continue If the thermal protector continues to activate after following the above steps your cleaner may need servicing see Service section 10 If you have a problem If a minor problem occurs it usually can be solved quite easily when the cause is found by using the checklist below Problem Cleaner won t run Possible Cause Possible Solution Not firmly plugged in Plug unit in firmly No voltage in wall plug Check fuse or breake Blown fuse or tripped breaker Replace fuse or reset breaker Thermal protector activated Allow cleaner to cool for 30 miinutes this will reset the thermal protector Problem Cleaner tools won t pick up Possible Cause Possible Solution Broken or worn belt Replace belt Agitator br
7. WindTunnel by HOOVER Review this manual before operating cleaner Index Assembling Cleaner 2 4 Cleaner Descriptions ssssssssnsnennrennnee 4 How To Use Embedded Dirt FINDER Feature 5 Cleaning Tools 7 Upright Cleaner 4 6 If You Have a Problem 11 Important Safeguards 1 Lubrication eene 11 Maintenance Authorized Service 11 Cleaning Filters 8 Clearing Blockages 10 Replacing Agitator 10 Replacing Belt 9 10 Replacing Edge Groomers 10 Replacing Headlight 9 Replacing Filter Bag 7 8 Thermal Protector 10 Unpacking Cleaner 2 Warranty ss 11 1997 The Hoover Company y Owner s Manual ENGLISH 2 pp 1 11 ESPANOL p g 12 17 FRAN AIS p 18 23 Thank you for selecting a HOOVER product This cleaner was inspected and packaged carefully before being shipped from the factory If you should happen to need assistance during assembly or operation call 1 800 944 9200 for an automated referral of authorized service outlet locations U S only or 1 330 499 9499 to speak with a representative in ou
8. andle close door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfaces Always disconnect cord from electrical outlet before servicing the cleaner Unplug cleaner when not in use Turn off all controls before unplugging Do not unplug by pulling on cord To unplug grasp the plug not the cord Never handle plug or appliance with wet hands The use of an extension cord is not recommended Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water take it to a Depot Factory Service Center or Authorized Hoover Warranty Service Dealer epot Use vacuum cleaner only for its intended use as described in the instructions Use only attachments recommended by The Hoover Company others may cause hazards Save these instructions Assembling cleaner It is extremely important to read and follow all instruction steps in order The assembled cleaner will look like this drawing If you need assistance with any step of the assembly call 1 800 944 9200 for an automated referral of service outlet locations U S only or 1 330 499 9499 to speak with a representative in our Consumer Response Center This cleaner is intended for house hold use STEP Unpack carton F E Remove all parts from carton Not required for a
9. ert agitator through belt and place belt in belt guide C on agitator Should the agitator shield D become dislodged while replacing the belt or the agitator reposition it as shown noting the placement of its belt guide E 38 Reposition lens and secure with the two screws Remove agitator and used belt Discard used belt 43 Grasp agitator firmly and fit it into position by first sliding end opposite the belt into the rectangular slot F on side of cleaner Pull other side of agitator G into place Turn agitator making sure belt is not pinched between agitator and agitator shield Continued 9 BA Reposition bottom plate and 4 Phillips head screws Tighten screws securely The edge groomers When to replace The edge groomers located on both sides of the nozzle should be replaced when they no longer extend past the surface of the bottom plate What to buy When purchasing edge groomers ask for HOOVER part No 39511004 How to replace Disconnect cleaner from electrical outlet Remove bottom plate as described in The belt section Fig 39 45 Lift off both old edge groomers and slide new edge groomers into position as shown Reposition bottom plate and secure with 4 Phillips head screws The agitator brush roll When to replace MESJ When agitator brushes are worn the agitator should be replaced To check condition of brushes move edge of a card across bottom
10. ly shut The final filter assists in the filtration process to return clean air to the room To remove this filter when it becomes dirty remove bag door and pull down top of filter How to replace Disconnect cleaner from electrical outlet 30 To change filter bag push down at top of bag door and pull door forward Remove door The secondary and final filters How to clean Disconnect cleaner from electrical outlet 3 The secondary filter A located behind the grill in the bottom of bag compartment protects the motor from dirt particles Si Lift out filter B and hand wash it in cold water with mild detergent Let filter air dry and reposition it on the side of cleaner Make sure green colored side of filter faces outward Reposition bag door 31 Grasp filter bag collar A and pull collar from tube B Note Do not clean out old filter bag and reuse Discard used filter bag Hold new filter bag as shown Align opening in filter bag with B Push A firmly onto B Tuck in filter bag If filter becomes dirty pull off grill and lift out filter Hand wash filter in cold water with mild detergent then air dry Reposition dry filter and grill Should you want to replace this filter ask for HOOVER part No 38765019 Should you want to replace this filter ask for HOOVER part No 38766008 Do not operate cleaner without either the secondary or fi
11. nal filter in place The headlight some models only What to buy This cleaner uses a 12 volt wedge base type 912 bulb Hoover part No 27313 101 How to replace Disconnect cleaner from electrical outlet Using a screwdriver remove the two screws as shown and lift off lens The belt The belt on your Hoover cleaner causes the agitator to rotate and is important for the effective operation of the cleaner The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is is in good condition When to replace Disconnect cleaner from electrical outlet To check belt remove bottom plate as shown in How to replace Replace belt if it is stretched cut or broken What to buy To assure effective operation use only genuine HOOVER belts with your cleaner When purchasing a new belt ask for HOOVER part No 38528 033 4 With lettering on outside of belt and positioned as shown in box on D slide new belt over motor pulley B 37 Pull old bulb straight out of socket Push new bulb straight into socket until locked in place Excessive force is not required How to replace Disconnect cleaner from electrical outlet Place handle in low position and turn cleaner over so bottom side is up Bie Remove the 4 screws as shown with a Phillips screw driver Lift off bottom plate A 42 Ins
12. ontains a high level of dirt which is being removed by the cleaner To decrease the feature s sensitivity to dirt set the switch to the Reg Regular position 5 Carpet height adjustment The cleaning of carpet and rugs takes place at the nozzle A When it is necessary to raise and lower the nozzle for various carpet pile heights slide the nozzle control knob B to the desired setting Cleaning lightweight flexible rugs Stand on one end of rug and move cleaner toward other end or edge Before reaching edge push down on handle This will lift up the nozzle front of cleaner as shown and will prevent rug from clinging to cleaner Continue to lift up nozzle so that when you have reached the edge it is completely off the rug Move cleaner back to start again lower nozzle and use only forward strokes 21 For ease in sliding knob the handle should be in the upright position C The nozzle will not move into the adjusted position until the cleaner handle is lowered to the operating position D Edge cleaning 24 Special edge groomers are provided on both sides of the nozzle to remove dirt in carpet near baseboards and furniture Guide either side of nozzle parallel to edge of carpet or furniture dU M re BARE FLOOR HIGH pp For maximum cleaning perfor mance the following carpet height settings are recommended Lowest setting for all types of carpet
13. oover Canada Burlington Ontario L7R 4A8 Phone 1 800 263 6376 Always identify your cleaner by the complete model number when request ing information or ordering parts The model number appears on the bottom of the cleaner Full One Year Warranty Domestic Use Your HOOVER appliance is warranted in normal household use in accordance with the Owner s Manual against original defects in material and workmanship for a period of one full year from date of purchase This warranty provides at no cost to you all labor and parts to place this appliance in correct operating condition during the warranted period This warranty applies when the appli ance is purchased in the United States including its territories and possessions or in Canada or from a U S Military Exchange Appliances purchased elsewhere are covered by a limited one year warranty which covers the cost of parts only This warranty does not apply if the appliance is used in a commercial or rental application Warranty service can only be obtained by presenting the appliance to one of the following authorized warranty service outlets Proof of purchase will be required before service is rendered 1 Hoover Factory Service Centers 2 Hoover Authorized Warranty Service Dealers Depots This warranty does not cover pick up delivery or house calls however if you mail your appliance to a Hoover Factory Service Center for warranty service transpor
14. r Consumer Response Center DO NOT RETURN THIS PRODUCT TO THE STORE Important Safeguards When using an electrical appliance always follow basic precautions including the following READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE W a r n l n g To reduce the risk of fire electric shock or injury Do not use outdoors or on wet surfaces Close supervision is necessary when any appliance is used by or near children Do not allow vacuum cleaner to be used as a toy or to run unattended at any time Keep hair loose clothing fingers feet and all parts of body away from openings rotating agitator and other moving parts Do not operate cleaner in bare feet or when wearing open toe shoes or sandals Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present Avoid picking up hard sharp objects with the cleaner They may damage the cleaner and the bag Always turn off this appliance before connecting or disconnecting hose Do not use without dust bag or filters in place Change bag frequently when picking up very fine materials such as powder Use extra care when cleaning on stairs Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair or anything that may reduce air flow Do not pull or carry by cord use cord as a h
15. r will not operate effectively For models with Check Bag indicator A the indicator will begin to show red as filter bag fills with dirt There are three conditions that will cause the indicator to become completely red 1 The bag is full change the bag 2 Very fine materials have been picked up clogging the bag pores change the bag 3 There is a blockage the nozzle hose tools or at the bag opening remove the blockage Clearing blockages p 10 CAUTION Very fine materials such as face powder cornstarch fireplace ashes or fireplace soot may seal the filter bag and may cause it to burst even though it is only partially full of dirt When cleaner is used to remove material of this nature change filter bag often Continued gt Where to buy Filter bags may be purchased from your Authorized Hoover Dealer Depot or from a Hoover Factory Service Center When ordering filter bags be sure to give the model number of your cleaner What to buy To assure cleaning effectiveness use only Genuine HOOVER Allergen Filtration Type Y disposable filter bags To assure that your cleaner operates at peak performance it is imperative that you use only genuine HOOVER filter bags made by The Hoover Company HOOVER bags can be identified by these trademarks Hoover 32 Reposition bag door by placing tabs on bottom of door into opening C Press top of door to snap secure
16. rt are removed To let you know that the Dirt FINDER feature is ready the red light will come on when the cleaner is first turned on After a few seconds the red light will go off and the green light will come on Cleaning may then begin IN To help keep the cord out of the way while vacuuming position cord down into cord clip A located between top cord hook and handle Transporting cleaner 7 To move your cleaner from room to room put handle in upright position tilt cleaner back on rear wheels and push forward The green light will remain on through out cleaning except when the detector senses that a larger amount of dirt is being picked up then the red light will come on When the red light is on you should take additional cleaning strokes in the area until it changes to green ESA Plug cord into electrical outlet To turn cleaner ON push switch B toward front of cleaner To turn cleaner OFF push B toward back of cleaner The cleaner can also be moved by using the carrying handle The red light may seldom come on during cleaning This means that your cleaner is picking up primarily fine surface dust and lint which the system may not detect or that the carpet is generally clean To increase the feature s sensitivity to dirt set the switch B to the Hi position At other times the red light may stay on for a considerable amount of time This means that the carpet c
17. ssembly and identify each item shown E Extra filter bag one already Make sure all parts are located installed in cleaner before disposing of packing F Extra belt one already installed in cleaner A Handle section B Cleaner body C Hose cleaning tools and wands D Handle bolts and nuts packet in bag with owner s manual Fill in and retain The model and serial number are located on the bottom of the cleaner as shown For your personal records please enter the COMPLETE model and serial number in the spaces provided and retain this information Your cleaner is model and has serial number It is suggested that you attach your sales receipt to this owner s manual Verifica Example tion of date of purchase may be required for warranty service of your HOOVER E product HOOVER CLEANER MODEL U5465 900 senes M 12 120V 60 Hz 120A BAG TYPEY Be sure to fill out and return the product registration card included with D SRI s RES H ser no 00000000004 your cleaner 263G DHOOVER co FOR HOUSEHOLD USE ONLY amp LJ PARA U80 HOGARENO SOLAMENTE POUR UN USAGE M NAGER UNIQUEMENT NATUO The Hoover Co N Canion Ohio 44720 LR 100852 Made In U S A Hecho en E U A Fabrique aux U STEP Il Attach handle Remove bag door on cleaner body by pushing down at top of door and pulling door outward Switch A above bag door should be in OFF position SR Place nuts in recessed areas
18. tation will be paid one way While this warranty gives you specific legal rights you may also have other rights which vary from state to state If further assistance is needed or if there are questions concerning this warranty or the availability of warranty service outlets write or phone the Consumer Response Center The Hoover Company 101 East Maple St North Canton Ohio 44720 Phone 1 330 499 9499 For an automated referral of authorized service outlets in the U S A phone 1 800 944 9200 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 1 800 263 6376 11 i HOOVER y son marcas registradas HOOVER OD sont des marques d pos es THE HOOVER COMPANY NORTH CANTON OHIO 44720 THE HOOVER COMPANY NORTH CANTON OHIO 44720 gt HOOVER and are registered trademarks THE HOOVER COMPANY NORTH CANTON OHIO 44720 R2 12 97 U5395 900 U5469 900 Litho USA 5651 1 A34
19. ush roll worn Replace brush roll Filter bag full e Change filter bag Incorrect carpet height setting Move nozzle control knob to lower setting Blockage in air flow passage e Clear blockage Problem Cleaner hard to push Possible Cause Possible Solution Incorrect carpet height setting Move nozzle control knob to a higher setting Lubrication The motor is equipped with bearings that contain sufficient lubrication for the life of the motor The addition of lubricant could cause damage Therefore do not add lubricant to motor bearings The agitator is equipped with two ball bearings that should be lubricated periodically by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer Depot Service To obtain approved HOOVER service and genuine HOOVER parts locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot by checking the Yellow Pages under Vacuum Cleaners Household OR checking the list of Factory Service Centers provided with this cleaner OR calling 1 800 944 9200 for an automated referral of authorized service outlet locations U S only Do not send your cleaner to The Hoover Company in North Canton for service this will only result in delay If further assistance is needed contact The Hoover Company Consumer Response Center North Canton Ohio 44720 Phone 330 499 9499 In Canada contact H
Download Pdf Manuals
Related Search