Whirlpool 56001190016/816519 Cooktop User Manual
Contents
1. B Assemble the flexible connector from the gas supply pipe to the pressure regulator in this order manual shuioff valve 1 2 nipple 1 2 adapter flexible connector 1 2 adapter and 1 2 nipple All connections must be wrench tightened 6 Use pipe joint compound made for use with NATURAL and L P gas to seal Numbers all gas connections If flexible connectors are used be certain correspond connectors are not kinked to steps PANEL C If the cooktop does not operate Check that the circuit breaker is not tripped or the fuse blown A more detailed troubleshooting checklist is provided in the Use and Care Guide NOTE Refer to Owner s Guide for operating instructions and cleaning instructions Part No 56001190016 816519 1990 Whirlpool Corporation If you need assistance During normal business hours the Whirlpool COOL LINE Service will answer any questions about operating or maintaining your cooktop not covered in the Installation Instructions Tne Whirlpool COOL LINE Service telephone number is 800 253 1301 Dial just as you normally dial long distance the call is fee When you call you will need the cooktop model number and serial number Both numbers can be found on the serial rating plate located on the front of the bumer box ol CORPORATION Prepared by Whirlpool Corporation Benton Harbor Michigan 49022 If you need service In the event that your2. Installation Instructions Part No 56001 190016 816519 30 Gas Sealed Burner Cooktop IMPORTANT Installer Leave Installation Instructions with the homeowner Homeowner Keep Installation Instructions for future reference Save Installation Instructions for local electrical inspector s use Note This cooktop is manufactured for use with NATURAL gas only Check location where cooktop w be installed The location should be away from strong draff areas such as windows Coors and strong heating vents or fans he cooktop should be located for convenient use in the kitchen ALL OPENINGS IN THE WALL OR FLOOR WHERE COOKTOP JS TO BE INSTALLED MUST BESEALED E max upper cabinel deplh See Note 4 min countertop po Nor seal cooktop tor un nee space trom lef side p __ cClearnce and O from righi side i gee ol cooklop to vertical Before you start Proper installation is your responsibility Make sure you have everything necessary for correct installation It is the responsibility of the installer to comply with the installation Clearances specified on the serial rating late The serial rating plate is located on the ont of the cooktop burner box Note This cooktop is manufactured for use with NATURAL gas only 30 min cabinei width above cooktop 1 min space between adjacent cooktops wall or other combuslible Pe material __ 18 min clearanc
3. Hazard Do Not obstruct the flow of combustion and ventilation air Personal Injury Hazard Cabinet storage above the cooking surface should be avoided It cabinets are already installed reduce the hazard of reaching over a heated cooking surface by insialling a range hood The range hood should extend a minimum of 5 inches out from the bottom front of the cabinets Reaching over a heated cooking surface could result in a serious burn Electrical Shock Hazard H is the customer s responsibility To contact a qualified electrical insiailer To assure that the electrical instatlation is adequate and in conformance with National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances Failure to do so could result in electrical shcck or other personal injury D Provide a gas supply line of a 3 4 rigid pipe to the cooktop location A smaller size pipe on long runs may result in insufficient gas supply Pipe joint compound made for use with NATURAL and L P gas must be used E If local codes permit A G A a certified flexible metal tubing new is recommended for connecting this cooktop to the gas supply line Do not kink or damage the flexible tubing when moving the cooktop A 1 2 male pipe thread is needed for connection to pressure regulator female pipe threads The supply line shall be equipped with an approved shutoff valve This valve shou
4. Whirlpool appliance should need service call the dealer from whom you purchased the appliance or a Whirlpool authorized service company A Whirlpool authorized service company is listed in the Yellow Pages of your telephone directory under Appliances Household Major Service or Repair You can also obtain the service company s name and telephone number by dialing free within the continental United States the Whirlpool COOL LINE Service telephone number 800 253 1301 A special operator will tell you the name and number of your nearest Whirlpool authorized service company Maintain the quality built into your Whirlpool appliance calla Whinpool authorized service company Printed in U S A
5. e of cabine Tools needed for Gas supply installation requirements Imporiant Observe all governing codes and ordinances AWARNING Fire Hazard Cooktop must be connected to a regulated gas supply This must be checked by a qualified technician before installing ine cooktop Do Not use an open flame to test for leaks from gas connections New flexible gas line must be used Failure to follow these insiructions could result in a fire explosion or personal injury fiat blade pliers screwdriver pipe wrench Mobile home installation The installation of this cooktop must conform to the Manufactured Home Construction and Safety Standards Title 24 CFR Part 3280 formerly the Federal Standard for Mobile Home Construction and Safety Title 24 HUD Part 280 or when such standard is not applicable the Standard for Manufactured Home Installations 1982 Manufactured Home Sites Communities and set Ups ANS A 225 1 latest edition or with local codes A Installation must conform with a local codes and ordinances In the absence of local codes installation must conform wib American National Stendard National Fuel Gas Code ANSI 2223 1 latest edition B Input ratings shown on the a serial rating plate are for elevations up to 2 000 feet For elevations above 2 000 feet ratings should be reduced at a rate of 4 for each 1 000 feet cbove sea level Copies of the standards l
6. e upper Width 30 cabinet to countertop So 24 lower cabinet depth oo AE or vertical wall 36 counienop height 30 min base cabinet Z tgrequired If cabinet Burner pox has a drawer a 3 depth t 3 a Note 30 min C earance from the 7 ei a Recommended Bren ponam all gas line area for 120V Of Sounterep to the openng 5i ies 8 A grounded outlet melal cabinet op of the drawer or below counte op i ead 27 on rear cabinet is prolecied Oner obstruction and cenlered in cabinet all ena DNs cabinet is arene Center line of tlame quired o Not pinch retardant power cord 1 wall andiunit millboard between cooklop covered with and caninel not less than No 28 MSG sheel sleel 10 015 stainiess steel 00247 aluminum or 0 020 copper 36 min clearance between top of the cooking platorm and Ihe bottom of an unprotecled wood or melal cabinet P lt Important Observe ail governing codes and ordinances Failure to meet codes and ordinances could lead to fire or electrical shock Le N 3 min to cabine space 10 backsplash or verlical wall Cutout dimensions Center line of floor Nae 26 5 8 min jopening width 4 counter space 4 trom lett side and 0 from right side of cooktop to Vertical wall or other combustible ___ malerial 4 19 opening depih 2 1 4 min space to front edg
7. isted may be obtained from National Fire Protection Association Batterymarch Park Quincy Massachusetts 02269 American Gas Association 1515 Wilson Boulevard Adinglon Virginia 22207 C This cooktop is equipped for use with NATURAL gas only and is design certified by A G A PANEL A Grounded electrical oullet is Caused EECC FCQuIeMENTS Proper gas supply conneclion must be evciiable See Gas suppiy requ Countenop opening dimensions inat are shown must be usec cre minimum clearances anc required 0 clearance NOTE Clearances spected ore for Se bees wails cond maternos tnal have 3 oO Sce ements Given dimensions provide censty cf 20 or more pour ds per CULIC foot No evaiuction of cleararces nas cee Bn Mace for insiaiations GC cceni to mo cnia s inat are iess thcn 29 it orio pasic ties ond she AWARNING FIRE HAZARD IMPROPER INSTALLATION ADJUSTMENT ALTERATION SERVICE OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE REFER TO THIS MANUAL FOR ASSISTANCE OR ADDITIONAL INFORMATION CONSULT A QUALIFIED INSTALLER SERVICE AGENCY MANUFACTURER DEALER OR THE GAS SUPPLIER cunds per no FOR YOUR SAFETY IF YOU SMELL GAS 1 OPEN WINDOWS 2 DO NOT TOUCH ELECTRICAL SWITCHES 3 EXTINGUISH ANY OPEN FLAME 4 IMMEDIATELY CALL YOUR GAS SUPPUER DO NOT NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPUIANCE AWARNING Fire
8. ld be located in the same room as the cooktop and should be in a location that allows ease of opening and closing Do not block access to the shutoff valve The valve is for turning on or shutting off gas to the appliance G If rigid pipe is used as a gas supply line a combination of pipe fittings must be used to obtain an in line connection to the cooktop All strains must be removed from the supply and fuel lines so cooktop will be level and in line H The regulator must be checked a ata minimum of 1 inch water column above the set pressure The inlet pressure to the regulator should be as follows for both operation and checking the regulator setting NATURAL GAS Minimum pressure 5 inches W C Maximum pressure 14 inches W C l Testing above 1 2 psi gauge a The cooktop and its individua shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1 2 psig 3 5 kPa Testing at 1 2 psi gauge or lower The cooktop must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1 2 psig 3 5 kPa PANEL B Electrical requirements AWARNING Electrical Shock Hazard Electncdl ground is required on this appliance Improper connection of the equipment grounding conductor con res
9. lectronic ignition System initial lighting Cooktop bumers use electronic igniters in place of standing pilots When the cooktop control knob is turned to the LITE position the system creates a spark to light the burner This sparking continues until the control knob is turned to the desired setting ore 1 Check the operation of the s cooktop burners Push in and turn each control knob to LITE position The flame should light within 4 seconds Do Not leave the knob in the LITE position after burner lights If the burners do not light properly turn the control knob to the OFF position Check that the burner cap is in the proper position Check that the power cord is plugged in and that the circuit breaker or fuse has not blown Check that the shutoff valve is in the ON position Check operation again If bumer does not light at this point contact your Whirlpoo dealer for assistance After burner lights turn s control to HI position Check each cooktop burner for proper flame The small inner cone should have a very distinct blue flame approximately 1 2 jong The outer cone is not as distinct as the inner cone The LO or simmen setting on each bumer has been factory set to the lowest setting available If any burner does not stay lit at the LO setting contact your Whirpool dealer for assistance Manual 1 2 adapter 1 2 adapter Teguictor Sirwiot valve
10. na grounding connector screw Do not ground toa gas supply pipe or hot water pipe Do not connect to electrical supply until appliance is permanently grounded See Figure 3 Bumps on grounding clamp must conlact pipe GROUNDING CLAMP MUST BE TIGHT ON PIPE No 4 Metal cold water pipe 2 Clamps Figure 3 Grounded cold water pipe must have metai coniinuity to electrical ground and not be interrupted by plastic rubber of other electrica insulating connectors such as hoses fittings washers or gaskets inciuding water meter or pump Any electrical insulating connector should be jumped as shown with a length of No 4 wire securely clamped to bare metal at both ends Now start With cooktop in kitchen Remove shipping materiais and tape from cocktop 2 Remove cooktop bumer grates s and cops package from shipping box Remove pressure regulator and hardware package from side of carton ACAUTION Property Damage Lift entire cooktop up from cutout when repositioning cooktop in countertop opening Failure to do so could scratch countertop Ds S lf 3 Insert the cooktop into the countetop cutout Center the cooktop in the cutout Check that the front of the cooktop is parallel to the front edge of the countertop Check that all required clearances are met If cooktop is not properly positioned lift the entire cooktop out of opening to make adjus
11. ong grounding type wall receptacle grounded in accordance with the National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances See Figure 1 If a mating wall receptacle is not available it is the personal responsibility and obligation of the customer to have a 3 prong wall receptacle installed by a qualified electrician 3 ptong grounding type wall receptacio D D 3 prong NES grounding lies Power supply cord Figure 1 Temporary grounding method THIS HOWEVER IS NOT RECOMMENDED DO NOT UNDER ANY CIRCUMSTQNCES REMOVE THE POWER SUPPLY CORD GROUNDING PRONG Grounding assembly atached Screw to grounded metal cold waler io pipe with paint removed soe Cover plale Grounded 3 prong eyelet ops grounding iwf a plug va 2 a T ENTE ie Wee TE oe Moplar pT 3 prong G are eras i ale ao grounding prong type wall teceplacie supply _ cor Figure2 Elecirical ground is required on this appliance If changing and properly grounding the wall receptacle is impossible and where local codes permit consult your electrical inspector a temporary adapter may be plugged into the existing 2 prong wall receptacle to mate with the 3 prong power supply cord See Figure 2 If this is Gone you must connect a separate copper grounding wire No 18 minimum to a grounded cold water pipe by means of a clamp and then to the exter
12. tments so that foam sealing strip can seal properly 4 install the pressure regulator with the arrow on the regulator pointing up toward the unit and in position where you can reach the access cap AWARNING Fire Hazard Do Not make connection too tight The regutator is die cast Overtightening may crack regulator resulting in a gas leak and possible tire or explosion 2 nipple 1 2 nipple Flexible connector shop Gumlmncqoch fe K 77 3 k 4 t Pressure Open the shutoff valve in the gas supply line Wait a few minutes for the gas to move through the gas line AWARNING Fire Hazard Do Not use an open flame to tes for leaks from gas connections Checking for leaks with a flame may result in a fire explosion or personal injury 8 Use a brush and liquid detergent to test all gas connections for leaks Bubbles around the connections will indicate a leak If a leak appears shut off gas valve controls and adjust connectors Then check connections again NEVER TEST FOR GAS LEAKS WITH A MATCH OR OTHER OPEN FLAME Clean all the detergent solution from cooktop Plug tne electrical cordintothe grounded outlet p Burner cap w iimg 1 0 Place trim rings over each a bummer Moke sure burner cap is properly aligned and leve Locate the tab on the burner cap and place over the white electrode in the bumer base Piace burner grates over bumen and caps E
13. ult in electrical shock Check with a qualified electrician it you are in doubt as to whether the appliance is property grounded Do Not modify the power supply cord plug i it wil noi fit the outlet have a Proper outlet instatiled by a qualified electrician Do Not use an extension cord with this appliance Do Not have a fuse in the neutral or grounding circuit A fuse in the neutral or grounding circuit could result in an electrical shock Failure to follow these instructions could result in fire ekectricdl shock of other personal injury A 120 vott 60 Hz AC only 15 ampere fused electrical supply is required A ime delay fuse or circuit breaker is recommended It is recommended that a separate circuit serving only this appliance be provided Electronic ignition systems operate within wide voltage limits but proper grounding and polarity is necessary In addition to checking that the outlet provides 120 volt power and is correctly grounded the outlet must be checked by a qualified electrician to see if it is wired with correct polarity A wiring diagram is included in the literature package Recommended grounding method DO NOT UNDER ANY CIRCUMSTANCES REMOVE THE POWER SUPPLY CORD GROUNDING PRONG For your personal safety this appliance must be grounded This appliance is equipped with a 3 prong grounding plug To minimize possible shock hazard the cord must be plugged into a mating 3 pr
Download Pdf Manuals
Related Search