Top Innovations SF-407 Iron User Manual
Contents
1. Steam Nozzle vertically from bottom to top of garment FIGURE 16 NOTE Do not allow kinks to form in hose at any time during use 4 Direct Steam Nozzle away from garment and smooth fabric with your free hand 5 Repeat steps 3 and 4 as necessary until fabric is smooth and wrinkle free i t t i FIGURE 16 OTHER STEAMING TIPS Curtains and draperies may be steamed while still hanging To remove wrinkles from towels handkerchiefs and napkins drape them over a rod or towel rack and gently steam them Heavier fabrics may require repeated steaming to effectively remove wrinkles To remove exceptionally stubborn wrinkles steam both sides of fabric For additional assistance in removing tough wrinkles or to remove lint and other particles attach Fabric Brush to Steam Nozzle see Attaching the Fabric Brush section on page 8 of this manual Use Press Pad in order to steam difficult spots and edges and to create creases in fabric Slide your hand through the velcro strap on back of Press Pad to secure it to your hand This will protect your hand from the flow of hot steam Then steam fabric while pressing it firmly but gently against the Press Pad 12 Top Innovations Inc Steam fi CARE AND STORAGE GUIDELINES PROPER STORAGE Preparing your Fabric Steamer for storage is quick and simple When you have finished your steaming tasks follow the steps listed below N W A n nN Set On O2. for unit to produce gurgling sounds and small amounts of water during the first few minutes of steaming This is a natural part of the steaming process Pointing Steam Nozzle towards the ground and shaking it gently may help to remove excess water from Steam Hose more quickly FIGURE 14 5 Once steam flow is steady and excess water has been removed from Steam Hose you may proceed with your steaming tasks Refer to Tips for Using the Fabric Steamer guide on page 12 of this manual for more information about steaming garments and other fabrics 6 When you have completed your steaming tasks immediately switch Lighted On Off Switch to Off position and unplug power cord from electrical outlet Refer to Proper Storage section on page 13 of this manual for information on proper cleaning and storage of Fabric Steamer FIGURE 12 FIGURE 13 FIGURE 14 Top Innovations Inc 11 steam Sli USING THE FABRIC STEAMER TIPS FOR USING THE FABRIC STEAMER STEAMING GARMENTS Wy 1 Place garment on a clean rust free clothes hanger l 2 Place hanger with garment on Clothes Hanger z 7N Hook FIGURE 15 i CAUTION Use care when handling garments on the Clothes Hanger Hook Pulling on the garment with too much force may cause the unit to tip over FIGURE 19 3 Grasp Handle and direct Steam Nozzle towards bottom of garment Steam will rise along inside and outside of fabric removing wrinkles Slowly slide
3. of Telescopic Pole FIGURE 3 E upwards to extend it to full height Re tighten top ridged knob Loosen bottom ridged knob FIGURE 3 D by turning it in a counter clockwise direction Pull middle section of Telescopic Pole FIGURE 3 F upwards to extend it to full height Re tighten bottom ridged knob 5 Telescopic Pole is now fully assembled and extended To reduce Pole back to compact height reverse steps 3 and 4 N w A NOTE The Telescopic Pole must be fully extended during steamer operation in order to insure a free flow of steam through the Steam Hose gt a ks l E 0 FIGURE 1 FIGURE 2 FIGURE 3 Top Innovations Inc 7 rz Steams 5 ft ASSEMBLING THE FABRIC STEAMER ATTACHING THE TELESCOPIC POLE 1 Loosen Pole Base by turning it in a counter clockwise direction 2 Insert bottom section of Telescopic Pole into Pole Base FIGURE 4 3 Tighten Pole Base by turning it in a clockwise direction until it is tight and Telescopic Pole sits firmly in place FIGURE 5 ATTACHING THE FABRIC BRUSH 1 Make sure Lighted On Off Switch is set to Off position and that the unit is not emitting any steam Do not try to connect Fabric Brush while unit is emitting steam as this can cause burns and injury 2 Align the four pegs on back of Fabric Brush 2 circular and 2 elongated with corresponding holes on face of Steam Nozzle 3
4. 1 Nozzles and attachments become hot during use To avoid injuries DO NOT touch nozzles while using this appliance DO NOT attempt to change attachments while unit is emitting steam 12 DO NOT turn unit on its side when in use 13 When filling your Fabric Steamer with water DO NOT fill Water Tank with more than 40 oz of water 14 Before filling unit with water always take the following steps 1 Turn appliance off 2 Unplug electrical cord Failure to follow these steps may result in electrical shock and injury 15 Only water should be used in unit Other cleaning agents will damage unit and can cause injuries 16 DO NOT operate unit if steam opening is blocked Should this occur shut unit off and unplug 17 Store your SF 407 Fabric Steamer in a cool dry place Allow unit to cool completely and always drain Water Tank and Reservoir before storing SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY 4 Top Innovations Inc Steam 261 EZETA asa e sso elerm ININ The following features and accessories are included with your Fabric Steamer Carefully inspect packaging material as some parts are shipped inside Styrofoam packaging To obtain possible missing parts refer to the Customer Support section on page 14 of this manual oo 0 ONO OT B00 Oar UNIT FEATURES AND ACCESSORIES Pole Top Clothes Hanger Hook Steam Nozzle Holder Fabric Brush Steam Nozzle Handle Steam Hose Hose Base Telescopic Pol
5. MODEL SF 407 Steam S M Fabric Steamer by Top Innovations Inc Please read all instructions before use Mail in your warranty registration card f LETTER FROM THE CEO Dear Valued Customer Congratulations on purchasing your new SF 407 Fabric Steamer This powerful product is designed to effectively smooth wrinkles and reduce odors with a minimum of time and effort Turn your Fabric Steamer on and in less than a minute you are ready to delicately remove wrinkles from garments draperies and upholstery With 1500 Watts of power and a forty five minute maximum steam time this Fabric Steamer is capable of handling everything from big steaming jobs to quick touch ups With the convenient Clothes Hanger Hook you can hang garments right on the unit for steaming In fact the Fabric Steamer is so versatile that it can effectively steam drapes while they are still hanging eliminating the hassle of taking them down This wrinkle removing power combined with its ability to reduce smoke pet and other unpleasant odors means that the Fabric Steamer will let you care for your precious fabrics and garments the way you ve always wanted to Top Innovations Inc would like to invite you to visit our Customer Support Web www steamfast com site at On this website you will find additional information about many other exciting products that are available helpful tips on ways in which you can utilize your Fabric Steame
6. Press Fabric Brush firmly onto Steam Nozzle until it fits snugly and firmly in place FIGURE 6 FIGURE 6 Top Innovations Inc Steam H ASSEMBLING THE FABRIC STEAMER ATTACHING THE STEAM HOSE 1 Place end of Steam Hose onto threaded Hose Base FIGURE 7 2 Rotate knob in clockwise direction until Steam Hose is tightly secured onto Hose Base FIGURE 8 Hand tighten only Do not over tighten 3 Hang Steam Nozzle on specially designed Steam Nozzle Holder FIGURE 9 D N A amp DS Sa ae FIGURE 7 FIGURE 8 FIGURE 9 CAUTION To prevent steam from causing bodily injury or damage to surfaces always hang the Steam Nozzle on the Steam Nozzle Holder when not in use Do not lay the Steam Hose on the floor as condensation may occur causing unwanted water droplets in the steam Do not pull on the Steam Hose with excessive force as this may damage it resulting in a steam leak Your new SF 407 Fabric Steamer is now fully assembled and ready for use Please continue reading this manual for instructions on using the Fabric Steamer as well as directions for cleaning and storage Top Innovations Inc 9 Steam ft USING THE FABRIC STEAMER FILLING WATER TANK AND WATER RESERVOIR IMPORTANT Always make sure that Lighted On Off Switch is set to Off position and unit is unplugged before attempting to fill Water Tank 1 Remove Water Tank from main unit 2 Holding Water Tank upside down u
7. e Pole Base Water Tank Valve Cap Water Reservoir Lighted On Off Switch Drain Plug Rolling Casters Press Pad Top Innovations Inc 5 GIE FABRIC STEAMER PRODUCT INFORMATION The Pole Top 1 is comprised of the Clothes Hanger Hook la and Steam Nozzle Holder 1b The Clothes Hanger Hook allows you to steam garments that are hanging from a clean rust free hanger The Steam Nozzle Holder provides a safe and convenient place to hang the Steam Nozzle The Fabric Brush 2 attachment connects to the Steam Nozzle and is designed to assist in removing lint loose threads and exceptionally stubborn wrinkles The Steam Nozzle 3 emits hot penetrating steam The Handle 4 is ergonomically designed for comfort and ease of use while remaining relatively cool and safe to grasp during the steaming process The Steam Hose 5 directs steam from the boiler to the Steam Nozzle and is designed to be flexible while safely containing the steam The Hose Base 6 is the threaded pipe which connects the Steam Hose to the main unit The Telescopic Pole 7 connects the Pole Top to the steamer and can be extended and retracted for convenient use and quick storage The Pole Base 8 is the point at which the Telescopic Pole connects to the main unit ensuring a stable mount for the Telescopic Pole The Water Tank 9 holds water to be used in the Water Reservoir and is removable for easy filling and emp
8. eated surfaces DO NOT use this unit with extension cords or electrical outlets that have inadequate current capacity A three prong outlet or a properly grounded adapter is necessary when using SF 407 Fabric Steamer In order to unplug SF 407 Fabric Steamer grasp plug and pull smoothly and firmly from outlet DO NOT attempt to unplug unit by pulling or tugging on electrical cord Use caution when operating unit as burns can occur from touching hot metal parts or from proximity to hot water or steam To reduce the likelihood of circuit overload do not operate another high wattage appliance on the same circuit SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY Top Innovations Inc 3 IMPORTANT SAFEGUARDS WARNING To reduce the risk of electrical shock this appliance has a three pronged plug This plug will fit in a polarized wall outlet only one way If the plug does not fit fully in the outlet contact a licensed electrician to install a proper outlet DO NOT attempt to modify the plug or defeat this safety feature 9 DO NOT handle or use this unit while hands are wet or when not wearing shoes To avoid falls and other injuries be sure to dry any wet areas on floors and to stand away from damp surfaces while using steamer 10 SF 407 Fabric Steamer is only meant to be used with recommended SF 407 accessories Other types of attachments are not to be used with this unit Doing so may cause injuries or damage to unit 1
9. egar solution from Water Reservoir Rinse Water Reservoir with fresh water drain and repeat until vinegar odor dissipates Replace empty Water Tank Top Innovations Inc 13 14 TROUBLESHOOTING amp CUSTOMER SUPPORT PROBLEM POSSIBLE CAUSE SOLUTION Unit is not plugged in Plug into electrical outlet Unit fails to steam Lighted On Off Switch does not illuminate Unit fails to steam Lighted On Off Switch does illuminate Excessive gurgling in Steam Hose and Steam Nozzle water drips from Steam Nozzle Steam output is weak or intermittent Household Circuit Breaker Ground Fault Interrupter has tripped or blown a fuse Water Tank is empty Mineral build up in unit Condensation in Steam Hose Mineral build up in unit Reset Circuit Breaker Ground Fault Interrupter or replace fuse If you need assistance contact a licensed electrician Refill Water Tank using procedures on page 10 of this manual Follow Removing Mineral Build Up procedure on page 13 of this manual Some gurgling is a natural effect of steaming process For excessive gurgling or dripping water point Steam Nozzle towards ground and shake to remove excess water droplets Follow Removing Mineral Build Up procedure on page 13 of this manual CUSTOMER SUPPORT For problems with your Fabric Steamer please refer to the troubleshooting solutions located above Additional inquiries should be directed to ou
10. ff Switch to Off position and unplug grounded power cord from electrical outlet Allow unit to cool completely Remove Water Tank from unit and unscrew Valve Cap to drain remaining water into sink or tub Remove Drain Plug and drain any remaining water in Water Reservoir into a sink or tub to prevent overfilling during your next use Flush out Water Reservoir with fresh water to minimize potential mineral build up in Water Reservoir Replace empty Water Tank Loosen two ridged knobs on Telescopic Pole and press down on Pole Top to collapse Pole into compact storage position Store Fabric Steamer in a cool dry place REMOVING MINERAL BUILD UP A common problem with steam appliances is mineral build up caused by high mineral content in many municipal water supplies The best way to avoid this is to use de mineralized or distilled water in unit If you are unable to use de mineralized or distilled water we recommend you use this procedure monthly to help avoid mineral build up hWON Or WnnN Unplug power cord from electrical outlet and allow unit to completely cool Remove Water Tank from unit and drain it into sink or tub Remove Drain Plug and drain water from Water Reservoir into sink or tub Using measuring cup not included make a mixture of 10oz vinegar and 10oz water Slowly pour water vinegar solution into Water Reservoir Allow to stand for 40 minutes Drain water vin
11. nscrew and remove Valve Cap by rotating it in a counter clockwise direction FIGURE 10 3 Fill Water Tank with water through Valve Cap Hole Refer to guidelines on left side of Water Tank to fill it with correct amount of water depending on desired steam time 15 30 or 45 minutes Do not exceed 45 MIN 40 oz mark NOTE To prolong life of unit it is recommended that you use distilled or de mineralized water in Water Tank Do not attempt to substitute another water tank for the one designed for use with this unit 4 Replace Valve Cap by rotating it in a clockwise direction 5 Place Water Tank back onto main unit FIGURE 11 The sound of water flowing from Water Tank into Water Reservoir should be audible for a short period of time IMPORTANT Do not attempt to operate Fabric Steamer with an empty Water Tank as doing so could result in damage to the unit SteamFast FIGURE 10 FIGURE 11 10 Top Innovations Inc Sit USING THE FABRIC STEAMER OPERATING THE FABRIC STEAMER 1 Make sure that Water Tank is filled with water and placed correctly onto main unit and that Fabric Brush is securely attached if you wish to use it 2 Plug power cord into a convenient 3 prong electrical outlet FIGURE 12 3 Switch Lighted On Off Switch to On position FIGURE 13 4 Unit requires approximately 35 40 seconds for boiler to heat Once it has heated Fabric Steamer will begin producing a flow of steam NOTE It is common
12. nty and out of warranty service requests 2 Include copy of purchase receipt 3 Include your name address telephone number and Return Authorization Number on returned package Please send product postage prepaid to TOP INNOVATIONS INC WARRANTY SERVICE DEPARTMENT 6655 TROOST AVE KANSAS CITY MO 64131 Should there be any missing or defective parts or accessories please contact Customer Support In most cases it is not necessary to return the entire unit We can ship most parts directly to your door Upon expiration of 1 year limited warranty you will be advised of the cost of repair before any servicing is done unless you enclose a note indicating that you would like us to proceed with repairs If you need to request warranty service or have any questions about coverage under this warranty please visit the Warranty Service Request page on our Web site www steamfast com You may also contact the Warranty Service Department by telephone at 800 711 6617 or 816 584 9700 or e mail customerservice topinnovations com Please have your product serial number ready before contacting Warranty Service Department The serial number is located on the back or bottom of your unit Top Innovations Inc 15 Steam asi Top Innovations Inc 6655 Troost Ave Kansas City MO 64131 Tel 800 711 6617 816 584 9700 www steamfast com customerservice topinnovations com Printed in China PRODUCT SERIAL NUMBER For yo
13. r and other useful information to assist you in maximizing the power of steam Enjoy your new SF 407 Fabric Steamer Za Benny Lee Chairman and CEO Top Innovations Inc 2 Top Innovations Inc _ Ww IMPORTANT SAFEGUARDS WARNING To reduce the risk of fire electrical shock or injury the following basic safety precautions should always be followed when using an electrical appliance READ ALL INSTRUCTIONS BEFORE USING YOUR STEAMER DO NOT leave your SF 407 Fabric Steamer unattended when plugged in or not in use this unit is not a toy Close supervision is required when using unit near children pets and plants Steam produced by unit is hot and pressurized Care must be taken to avoid burns or other injuries Never point nozzle at people or pets Always unplug electrical cord when unit is not in use DO NOT use this unit if electrical cord or outlet is damaged DO NOT use unit if it is not working properly or has been dropped damaged or left outdoors If such damage occurs contact our Customer Service Department see page 14 of this manual for service and repair assistance This unit is an electrical appliance DO NOT submerge it in water DO NOT use Steam Hose or electrical cord as a handle DO NOT allow cord or Steam Hose to be crimped by closing them in doors DO NOT pull or stretch cord or Steam Hose around sharp corners or edges Be sure to keep electrical cord away from all h
14. r Customer Support services through our Web site www steamfast com on the Service Request Web page If you do not have internet access you may also contact our Customer Support department by telephone at 800 711 6617 or 816 584 9700 NOTE In order for our customer service representatives to help you as quickly and efficiently as possible please have the following information ready before calling Purchase information where and when you purchased this product Product Serial Number Top Innovations Inc ih WARRANTY INFORMATION ONE YEAR LIMITED WARRANTY If outside USA additional shipping charges may apply Top Innovations Inc warrants this product to be free from defects in material and workmanship for a period of one 1 year from the date of purchase This warranty does not cover damage caused by misuse negligence use by improper current or voltage use contrary to operating instructions or disassembly repair or alteration by any person other than Top Innovations Inc Warranty Service Department Top Innovations Inc will repair or replace at its option This warranty gives you specific legal rights and may have other rights which may vary from state to state Performance of any obligation under this warranty may be obtained by 1 Call 800 711 6617 for Return Authorization Number before returning for repair Failure to obtain a Return Authorization Number will cause a delay in warra
15. tying The Valve Cap 10 controls the flow of water between the Water Tank and Water Reservoir and must be removed in order to fill and empty the Water Tank The Water Reservoir 11 is where water is stored before being converted into steam by the boiler Water is introduced into the Water Reservoir through the Valve Cap on the Water Tank The Lighted On Off Switch 12 activates and deactivates the unit as well as provides a clear visual indication that the unit is powered on The Drain Plug 13 is designed to easily empty water out of the Water Reservoir The Rolling Casters 14 allow for exceptional mobility and freedom of movement The Press Pad 15 fits on your hand allowing you to support the fabric for a more thorough steaming The Press Pad also protects your hand from being burned by hot steam REPLACING ACCESSORIES To order a replacement Press Pad or Fabric Brush visit the Products section of our website www steamfast com or call 1 800 711 6617 6 Top Innovations Inc LAST ASSEMBLING THE FABRIC STEAMER ASSEMBLING THE TELESCOPIC POLE Screw Pole Extension FIGURE 1 A onto top section of Telescopic Pole FIGURE 1 B Rotate in a clockwise direction until tight and secure Place Pole Top onto top of Pole Extension as shown FIGURE 2 and rotate in a clockwise direction until tight and secure Loosen top ridged knob FIGURE 3 C by turning it in a counter clockwise direction Pull top section
16. ur convenience space has been provided below for you to record the serial number of your unit located on the back or bottom of the unit for easy reference when contacting our Customer Service Department V050510
Download Pdf Manuals
Related Search