Sonance Sonamp ASAP2 SAT Stereo Power Amplifier Stereo Amplifier User Manual
Contents
1. Typical applications would be Control from switched outlet through a wall wart DC Voltage output of preamp or control device Relay drive output from out Navigator Master Keypad Individual zone control such as Sonance Nav Net controller Caution NEVER Connect to 120VAC line current AC Power Trigger Dip switch 3 On UP Position The B input relay may also be activated by the AC power trigger This is controlled by an AC outlet on rear panel which allows the ASAP2 to stay locked on to the local TV even when the audio signal is muted for an extended period of time Plug your TV into this outlet set trigger select DIP switch 2 to On position No Automatic Trigger Dip switch 4 On UP Position This allows the ASAP2 to stay locked on to the local source bypassing all automatic functions This application would be used when ASAP is in a switched outlet When off there would be direct pass through When on local ASAP2 inputs would be active Pressing front panel power button would allow manual switching from Main to Local sources Time Delayed Input Muting for AC Trigger Mode The ASAP2 mutes the input for 3 seconds to prevent thumps and pops created from low quality audio sources Typically television audio will produce audible thumps on the line out jacks This application would be used when ASAP is ina the AC trigger mode When off there would be direct pass through When TV is powered on local ASAP2 inputs2. would be active and wait for 3 seconds for audio to pass The muting is instant turn off to catch quick off thump This feature may be defeated if source equipment does not exhibit turn on off thumps or is using modes other than AC triggering Audio Video Trigger Control Adjustment Input Sensitivity The ASAP2 can be adjusted for input sensitivity using the recessed screw adjustment labeled sense on the front panel As it is turned clockwise the sensitivity increases counterclockwise makes it less sensitive The unit should be set for the highest level of sensitivity that allows proper continuous operation Operate the B source at a moderate volume then mute the signal if using a CD or tape player put it in pause The ASAP2 should switch back to the A source after the time delay period you set above and stay there If the sensitivity is set too high random switching may occur as the unit sense the residual noise level of the B source Some experimentation may be necessary but once it is set properly the ASAP2 will not need re adjusting unless the components are changed AC Trigger Control Adjustment front panel With TV or component on adjust trigger control by using the recessed screw adjustment labeled A C Trig to the point of trigger Then turn 1 8 past that setting Check operation by switching TV or component on and off If switching remains on reduce the trigger setting slightly Some components have a small change
3. 02 1 13 PM Page 5 1 Unscrew and save the two screws holding the current module in place 2 Pull the module out of the SAT module bay 3 Disconnect the ribbon cable 4 Select the desired position of any jumpers on the SAT module i e high pass filter 5 Connect the ribbon cable to the ribbon cable connector on the new module 6 Slide the SAT module into the SAT module bay 7 Replace the two mounting screws The following diagrams explain how each SAT module can be used with the ASAP2 SAT modules such as the LR1 AL1 and ASLI all sold separately are available Contact your Sonance Authorized installer or dealer for more information LR1 Module sold separately LR1 MODULE SONAMP SMART AMPLIFIER TECHNOLOGY L L O casey UNBALANCED OUTPUT The LR1 Balanced Line Receiver Module sold separately features a circuit that cancels out noise on long audio runs usually greater than thirty feet This module has an input impedance of 10KQ and is perfectly matched with the Sonance LS1 Balanced Line Sender The LR1 Module provides unbalanced stereo output jacks to feed the signal to other amplifiers The output is set at unity gain The following diagram shows a dean looking Plasma TV In Wall Speaker installation by using the Sonamp ASAP2 with the LR1 module at the equipment rack with the plasma AC triggered by the ASAP2 Simply swap out the SAT module with the LR1 module and connect the equipment as sh
4. appliance should not be situated on a bed sofa rug or similar surface that may block the ventilation openings or placed in a built in installation such as a bookcase or cabinet that may impede the flow of air through the ventilation openings 9 Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat 10 Power Sources The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance 11 Grounding or Polarization Precautions that should be taken so that the grounding or polarization of the appliance is not defeated 12 Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the appliance 13 Cleaning Dust the product with a clean cloth NEVER use water 14 Non use Periods The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time 15 Object and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings 16 Damage Requiring Service The appliance should be serviced by qualified service personnel when A The powe
5. enough wire 1 2 to fit into the slot in the terminal Before inserting the wire twist all its strands tightly to prevent strays that could cause a short circuit between and terminals If you use line level inputs run RCA patch cords from the variable outputs on the TV set or other local source If the local source has both line level and speaker level outputs use the line level outputs for better performance Video Trigger Dip switch 1 On UP Position The B input relay may also be activated by the video trigger This is a composite video RCA jack which allows the ASAP2 to stay locked on to the local TV even when the audio signal is muted for an extended period of time Run a single RCA patch cord from the video output source on the receiver or TV to the video trigger input on the ASAP2 An additional looping jack output is provided to pass through on to the TV video input Set the trigger by selecting DIP switch 1 to ON position Set Audio trigger to 1 2 rotation 33 2381 asap2 manual qxd 4 29 02 1 13 PM Page 4 Note the video jack is for triggering purposes only video signal switching is not possible External Voltage Trigger Dip switch 2 On UP Position The B input relay may also be activated by a low voltage control source This is by connecting a 5 to 24 Volts AC or DC power source to the screw terminal block on rear panel This allows the ASAP2 to stay locked on the local source any time power is applied
6. in current draw and may be e more difficult to trigger In this case audio video or low voltage may be an alternative option for better triggering stability Local to Main Delay Control Time Adjustment front panel The ASAP2 features an adjustable time delay which varies the amount of time it takes for the device to revert to the A input after the B input signal has been discontinued This delay time is set using the screw adjustment on the ASAP2 front panel labeled Delay The range is from 3 seconds fully counterclockwise to 90 seconds fully clockwise Set it for somewhat longer times if the video trigger is not used or the local system is used for classical music or other sources containing long quiet passages If using audio for triggering set the timing longer If triggering other than audio the delay time can be set to the shortest time setting counterclockwise Local Source Volume Control Adjustment front panel There are screw adjustments on the front panel for left and right volume control marked L amp R of local or internal power amplifier Use these controls for the volume a If the Local input signal is distorted or increase it if Local source has weak output Typically TV variable output falls into the category b If using a variable preamp receiver output leave them in the fully clockwise position c If using ASAP2 with passive volume controls set the passive volume control to maximum
7. the Main music system normally and then switch to the Local music source automatically BASH POWER AMPLIFICATION The Sonamp ASAP2 uses a new revolutionary power amplifier technology called BASH that is high efficiency and requires very little heat sink area Conventional power amplifier technology to produce the same power output would require massive heat sinks and a larger chassis for cooling The amplifier is fully protected against overheating short circuits and low impedance loading UNPACKING Save your carton and the styrofoam inserts for future safe transport in case you move or the unit ever requires shipping for repair Note it is best if you place it into an additional outer overcarton before shipment to minimize a chance of theft in shipment Before you proceed find the serial number which is located on the rear panel of the unit and note it here for future reference Serial PLACEMENT OF YOUR ASAP2 SAT The ASAP2 is designed to operate automatically and is housed in a compact chassis that can be mounted out of sight The unit can be placed horizontally on its rubber feet or the rubber feet can be easily removed by peeling them off of the bottom of the chassis for rack mounting When used with a TV set it may be convenient to hide the unit on the back or side wall of the cabinet or bookshelf not on the TV itself The ASAP2 features screw mounting holes on the bottom of the chassis see figure on top of next c
8. 33 2381 asap2 manual qxd 4 29 02 1 13 PM Page 1 PN 33 2381 4 02 The Leader in Architectural Audio IMPORTANT SAFETY INSTRUCTIONS CAUTION Read all of these instructions before you operate and save instructions for later use 1 Read Instructions all the safety and operating instructions should be read before the appliance is operated 2 Retain Instructions The safety and operating instructions should be retained for future reference 3 Heed Warnings All warnings on the appliance and in the operating instructions should be adhered to 4 Follow Instructions All operating and use instructions should be followed 5 Water and Moisture The appliance should not be used near water for example near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool Ex Carts and Stands The appliance should be used only with a cart or stand that is stable and sturdy enough to hold the product An appliance and cart combination should be moved with care Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn N Caution To prevent electric shock do not use this polarized plug with an extension cord receptacle or other outlets unless the blades can be fully inserted to prevent blade exposure 8 Ventilation The appliance should be situated so that its location or position does not interfere with its proper ventilation For example the
9. S FILLED WITH LIQUIDS SUCH AS VASES SHALL BE PLACED IN THE APPARATUS WARNING MOVE WITH CARE 33 2381 asap2 manual qxd 4 29 02 1 13 PM Page 2 A ASAP2 SAT 2 3 eB 3 45 6 7 7 8 99 10 11 12 A FRONT PANEL 1 POWER SWITCH 2 ACTIVE L E D 3 POWER L E D 4 A amp B INPUT L E D S 5 AC TRIGGER SWITCH 6 A B INPUT DELAY SWITCH 7 INPUT SENSITIVITY SWITCH 8 L amp R VOLUME CONTROLS B REAR PANEL AUDIO RCA INPUT OUTPUT JACKS LINE LEVEL SPEAKER LEVEL INPUT SWITCH SPEAKER INPUT CONNECTORS COMPOSITE VIDEO INPUT OUTPUT JACKS AUDIO MUTE BYPASS SWITCH MAIN INPUT QUICK CONNECTORS SPEAKER A amp B OUTPUT QUICK CONNECTORS TRIGGER MODE DIP SWITCHES 12 VOLT DC CONTROL INPUT OUTPUT 10 SWITCHED RECEIVER OUTLET OONOTAWM FUSE 12 POWER CORD CONNECTION BASIC CONCEPT The audio amplifiers in most televisions even monitors usually deliver a few watts not enough to properly drive many external speakers connected to the set The ASAP2 amplifies any local sound source like a TV or Multimedia and will deliver 50 Watts per channel into 8 ohms or 65 watts per channel into 4 ohms It also provides flawless automatic switching between the Local source TV and a Main house audio system The versatile triggering system will allow multitude of automation possibilies When connected to both sources the ASAP2 enables the local area speakers to play
10. Then adjust ASAP2 volume controls to nominal level without distortion AC Fuse This will blow to protect the unit for possible internal parts failure Never replace the fuse with any size other than indicated on the rear panel to avoid more serious damage Substitution of a larger fuse may create serious damage to internal parts and will void your Sonance warranty Note For continued protection against fire replace fuse with only same type and rating SAT MODULE BAY INSTALLATION The Sonamp ASAP2 features a Smart Amplifier Technology SAT module bay for future upgadability greatly increasing the flexibility of the amplifier and making it compatible with new protocols A new module can be easily inserted or swapped with another SAT module Refer to the following steps and the figure below for SAT Module removal and installation Note Make sure power switch is Off and AC Voltage is disconnected BASIC MODULE REMOVAL ia TOP VIEW OF MODULE CONNECTOR BASIC MODULE INSTALLATION 1 IEA NOTE WHEN INSTALLING NEW MODULE MAKE SURE POWER SWITCH IS OFF AND AC VOLTAGE IS DISCONNECTED f SET ANY JUMPERS ON MODULE CARD INCLUDING HIGH PASS FILTER Sa ail JUMPERS TO DESIRED LOCATIONS d CONNECT SAT MODULE TO RIBBON CABLE NOTING CONNECTOR ALIGNMENT 33 2381 asap2 manual qxd 4 29
11. cal input automatic mode activity Voltage Turn On Mode switch set to CENTER or External Volt position The Sonamp ASAP2 features a removable voltage input connector to connect other electronics with voltage control outputs When the dip switch is set to Voltage Trigger mode the voltage trigger monitors the voltage input connector and turns on the amplifier when voltage either AC or DC between 5V and 24V is detected Voltage Output Connector The Sonamp ASAP2 features a removable voltage output connector to provide 12VDC to control other devices such as Sonance Industry Upgrades 12 V relays or other Sonamps The current draw should not exceed 200mA e OPERATING THE ASAP2 Make all speaker input and control connections before applying AC power Connect the ASAP2 to an unswitched AC outlet Or switched outlet for bypass mode Power up the rest of the system and proceed with the adjustments below Audio Muting Bypass Switch rear panel Set this switch to ON position if using the AC trigger function to minimize thumps or pops from television audio outputs If using Audio Video triggering set to OFF for fastest transition to local source Line Level Speaker Level input switch rear panel Set to the appropriate input used choosing the best input for the application Line level is preferred for lowest noise and distortion Line level and Speaker sources cannot be used together Trigger Mode DIP Switch rear
12. for easy installation Plug the female end of the power cord into the inlet in the rear panel and plug the male end into a grounded wall socket DO NOT plug the power cord into an AC outlet on your preamplifier receiver CAUTION THE PREVENT ELECTRIC SHOCK DO NOT DEFEAT THE THIRD PRONG OF THE POWER CORD PLUG ATTENTION A FIN D EVITER TOUT RISQUE D ELECTROCUTION NEPAS ENLEVER LA 3EME FICHE DE LA PRISE ELECTRIQUE Use only a heavy duty extension cord if required to avoid starving the amplifier of all the current necessary for full power operation Speaker Wiring Two pairs of parallel output quick connect screw terminals are provided Connect the local loudspeakers to the Speaker A or B terminals on the back of the ASAP2 If using two pairs of speakers use only speakers with an impedance of 6 ohms or greater Use bare wire and strip only enough wire 1 4 to fit into the slot in the terminal Before inserting the wire twist all its strands tightly to prevent stray strands that could cause a short circuit between and terminals Tighten each terminal connection securely Main Input This speaker level input is the default or main input when no trigger stimulus is applied If the power is disconnected the audio passes through the main input directly to the speaker outputs If the Red Main source LED is lit then you are listening to Main input Pressing the power button off will force the unit to Main input This will lock out all Lo
13. n RMA number or it will be returned to you 3 If you are directed to return the unit to Sonance for repair pack the unit in its original shipping cartons inner amp outer Replacement packaging can be obtained from Sonance for a small charge 4 Contact United Parcel Service Federal Express or RPS to arrange prepaid not collect shipping Do not use the United States Postal Service IMPORTANT Freight collect shipments will be refused 5 Write the Return Merchandise Authorization number on the outside of the shipping carton 6 For warranty work please include a copy of the original bill of sale inside the package Ship the packaged unit to Technical Assistance Department Sonance 212 Avenida Fabricante San Clemente CA 92672 7531 e WARRANTY COVERAGE USA ONLY If within five 5 years from the date shown on the bill of sale the unit fails due to a defect in workmanship or materials Sonance will at its option and at no charge to the purchaser repair or replace the components of such unit which proves to be defective For this warranty to be effective the bill of sale must show that the unit was purchased from an authorized Sonance retailer This warranty shall apply exclusively to the original purchaser and shall not apply to units purchased for industrial or commercial use Furthermore this warranty shall not apply if 1 Damage to the unit was caused by accident abuse or misuse 2 The unit was m
14. odified or repaired by unauthorized personnel 3 The unit was not used as outlined in the operating instructions Exclusions and Limitations The warranty set forth above is in lieu of all other warranties express or implied of merchantability fitness for a particular purpose or otherwise The warranty is limited to Sonance products registered herein and specifically excludes any damage to any associated equipment which may result for any reason from use with this product Sonance shall in no event be liable to incidental or consequential damages arising from any breach of this warranty or otherwise This warranty gives you specific legal rights and you may have other rights which vary from state to state SPECIFICATIONS Output Power Stereo mode RMS 50 Watts per channel 8Q 65 Watts per channel 4Q 0 2 20Hz 20kHz 8Q 1 0 20Hz 20kHz 402 3 seconds to 90 seconds adjustable 785 Total Harmonic Distortion B to A Delay BTU HR Protection Circuits AC fuse thermal short circuit 100dB below rated output A weighted 300MV for 59W 8Q Signal to Noise Ratio Input Sensitivity Input Impedance 47k Q Min Power Requirement 120 VAC 50 60 Hz Power Consumption 360 watts Dimensions WxHxD Specifications and features subject to change without notice SONANCE 212 Avenida Fabricante San Clemente CA 92672 7531 Technical Support 800 582 0772 2002 All rights reserved Sonance is a registe
15. olumn Mount the ASAP2 vertically with the heat sinks on top As with any other power amplifier allow for adequate air circulation around the unit and do not mount it in direct sunlight or near a heat source such as hot air ducts or radiators BASH is a registered trademark of Indigo Incorporated MOUNTING SCREW HOLES DO NOT PLUG THE ASAP2 IN UNTIL ALL OTHER CONNECTIONS ARE MADE MAKE SURE ALL SOURCE AMPLIFIERS BEING CONNECTED TO THE UNIT ARE OFF MAKING CONNECTIONS Before making any signal or speaker connections make sure your power amplifier is turned off and unplugged When making connections make sure there is no strain or tension on input leads or speaker wires that could cause them to pull loose later on Input and Output Connections Speaker Level Outputs from a Local TV 555 ouTpUT MAIN DISTRIBUTED AUDIO SYSTEM Line Level Outputs from a Local TV INPUT 1234 Use the RCA jacks for the R and L channels Make sure these are consistent with the R and L outputs from your preamplifier receiver Looping Jacks Your ASAP2 provides a pair of RCA output jacks which duplicate the input signal These facilitate connection of additional power amplifiers from a single source component With these un buffered output jacks you can link o
16. own in Figure below FROM WHOLE HOUSE AC TRIGGER MUSIC SYSTEM DIP SWITCH 2 ON 50 FEET BALANCED AUDIO CABLE UNBALANCED OUTPUT TO 1 ONE INPUT OF NAVIGATOR HARBOR FOR MULTI ZONE DISTRIBUTION PLASMA TV SONANCE SONANCE SILHOUETTE III SILHOUETTE II e AL Module sold separately wv ALI MODULE SMART AMPLIFIER TECHNOLOGY CONTRI Oo UTEUTE D Or 0e TOA SENS DELAY INPUT A B DEFAULT SENSING OUTPUT The ALI Automatic Line Level Switcher Module sold separately has a default input as well as a sensing input When signal is detected at the sensing input that signal is fed to the amplifier as well as the output jacks At the same time a 12VDC control signal is present on the removable screw connector The sensing input has a sensitivity control as well as a delay adjustment which controls the time the module waits after the sensing jack signal subsides before switching back to the default input The following diagram shows a ASAP2 amplifier with the AL module in a restaurant installation The default input is connected to the house restaurant audio and the sensing input monitors to the paging microphone The output is feeding a second ASAP2 for two source amp whole house switching Simply swap out the Basic SAT module with
17. panel On the rear panel there is a small DIP switch for selecting one or more combination of trigger to local source The default factory setting is audio video trigger switch 1 Switch functions DIP switch 1 Audio Video source trigger Default DIP switch 2 External low voltage trigger 5 to 24 Volts AC or DC DIP switch 3 AC power outlet trigger DIP switch 4 Bypass of automatic triggering Forced local source setting A combination trigger application would be an Audio Video trigger by VCR signal and an AC Trigger by television power draw Audio Trigger Dip switch 1 On UP Position ASAP2 includes two source inputs The default or A input is for the remote house music system that will play whenever the local source is off or completely muted These inputs are at speaker level and are direct pass through Connect the remote house music system here The Sensing or B input is for the local source component such as a TV DVD or CD player tape player or portable stereo Whenever this local source is turned on and there is an audio signal present at the B inputs the ASAP2 automatically switches itself into the circuit amplifying the local signal and driving the room loudspeakers The B inputs have both speaker level connections and line level connections RCA jacks Select either one by sliding the switch on the rear panel to connect to the local system If you use the speaker level inputs use bare wire and strip only
18. r loop amplifiers without messy Y cord adaptors Speaker Connections Very Important Before starting the output connections are naturally in bridged mode This means that the negative terminals are inverting power amplifiers NO COMMON GROUNDS Do not connect negative terminals together under any circumstances Never use 3 conductor wire sharing the negative output terminals 33 2381 asap2 manual qxd 4 29 02 1 13 PM Page 3 Polarity It is important to observe correct polarity when using stereo mode One side of the speaker lead will have some sort of mark either printing a raised ridge on the insulation or different color of conductor This permits you to know which wire you had connected to the and which to the speaker terminals so you can do exactly the same at the power amplifier terminals Use Good Wire For best results you should never use thin gauge speaker wire it will constrict the sound and deteriorate bass response We recommend use of premium Sonance MediaLinQ speaker cable which also complies with UL fire rating Be sure to check local codes governing wire that may be installed within walls or ceilings Each brand of wire will have a different characteristic sound and some may be more compatible with the sonic signature of your various components Your Sonamp ASAP2 is stable with any reputable brand of wire and speaker cable AC Line cord The ASAP2 features a removable IEC power cord allowing
19. r supply cord or the plug has been damaged B Objects have fallen or liquid has been spilled into the appliance C The appliance has been exposed to rain D The appliance does not appear to operate normally or exhibits a marked change in performance E The appliance has been dropped or the enclosure damaged 17 Servicing The user should not attempt to service the appliance beyond that described in the operating instructions All other servicing should be referred to qualified service personnel INSTALLATION SONAMP STEREO INSTRUCTIONS ASAP2 SAT POWER AMPLIFIER CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO AUTHORIZED SERVICE PERSONNEL The lighting flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE THE APPARATUS SHALL NOT BE EXPOSED TO DRIPPING SPLASHING AND THAT NO OBJECT
20. red trademark of Dana Innovations www sonance com 6 16 3 4 x 1 3 4 x 11 5 8 425mm x 44mm x 295mm
21. the AL1 module and connect the equipment as shown in the figure below MAINTAINING YOUR SONAMP ASAP2 MICROPHONE PREAMP TO SPEAKERS TO SPEAKERS The Sonamp ASAP requires no periodic maintenance and has no user serviceable parts inside Do not remove the top cover to avoid risk of electric shock To keep it clean use only a soft cloth and never use any solvents or abrasives Fingerprints may be removed with a soft cloth moistened only with a few drops of water 33 2381 asap2 manual qxd 4 29 02 1 13 PM Page 6 SERVICE If you have any questions about the operation or installation of your Sonamp ASAP2 please call our Technical Assistance Department on any business day at 800 582 0772 or 949 492 7777 from 7 a m to 5 p m PST Should your product require repair or service contact your authorized Sonance retailer for help or use the following procedure 1 Prior to calling note the product model number serial number purchase date and original retailer s name and address 2 Contact our Technical Assistant Department at the number s above and describe the problem If required a Return Merchandise Authorization RMA number will be issued IMPORTANT Do not return the unit to Sonance without first obtaining a
Download Pdf Manuals
Related Search