Snapper BH500 Lawn Mower User Manual
Contents
1. Inspect the area where the equipment is to be used and remove all objects such as rocks toys and wire which can be thrown by the machine Use extra care when handling gasoline and other fuels They are flammable and vapors are explosive a Use only an approved container b Never remove fuel cap or add fuel with the engine run ning Allow engine to cool before refueling Do not smoke c Never refuel or drain the machine indoors Check that operator s presence controls safety switches and shields are attached and functioning properly Do not operate unless they are functioning properly OPERATION Never run an engine in an enclosed area Operate only in the daylight or with good artificial light keeping away from holes and hidden hazards Be sure of your footing while using pedestrian controlled equipment especially when backing up Walk don t run Do not operate in reverse unless absolutely necessary Always look down and behind before and while traveling in reverse Be aware of the blower discharge direction and do not point it at anyone Do not operate the blower without hose and bagger hood in place Never leave a running unit unattended Always stop engine before leaving unit Never operate with guards not securely in place Be sure all safety features are attached adjusted properly and func tioning properly Never operate with the hose or hood removed or altered Do not chang2. WELDMENT Blower Belt Guard NUT 1 2 13 Hex Nyloc WASHER 1 2 Flat SAE PULLEY A Groove Idler Steel IDLER STUD 3 8 24 thread FLAT WASHER 9 16 Type Narrow FLANGE BEARING 9 16 1 D powdered metal RETAINING RING 1 2 BELT RETAINER Idler SCREW 5 16 18 x 1 1 4 Hex Head Cap GR5 WELDMENT Idler Arm NUT 5 16 18 Hex Flange Lock SCREW 1 2 13 x 2 1 2 Hex Head Cap GR5 WELDMENT Blower Housing BACK PLATE Blower SCREW 5 16 18 x 3 4 Hex Washer Self Tap BEARING Pillow Block Blower includes grease fitting NUT 7 16 14 Hex Center Lock GR5 or B SCREW 7 16 14 x 1 1 2 Hex Head Cap GR5 IMPELLER Fast Vac Blower weldment SCREW 7 16 14 x 1 1 4 Hex Head Cap GR5 NUT 3 8 16 Hex Flange Lock BELT RETAINER PULLEY Flat Idler 2 3 4 O D WASHER 3 8 Flat SAE SCREW 3 8 16 x 2 1 4 Hex Head Cap GR5 NUT 3 8 24 Hex Nyloc SCREW 3 8 16 x 2 Hex Head Cap GR5 U CLIP 5 16 18 SCREW 5 16 18 x 3 4 Hex Washer Self Tap 13 SNAPPER Z VAC BLOWER MOUNT GROUP CZT HZT Models 14 z 3 OANDOOARWDNDM Part No 3036323 3037161 Qty Snapper Z Vac Blower Mount Group CZT HZT Models Description BELT A Section 91 125 effective length WELDMENT Belt Cover Deck NOT USED WING LOCKNUT 5 16 18 BELT GUARD PULLEY Blower Input PULLEY Spindle WELDMENT Blower Mount WELDMENT Guard Support Bracket SCREW 5 16 18 x 3 4 Hex Washer Self Tap WELDMENT Deck Mount Bracket SCREW
3. 1 Empty Grass Catcher bags often to avoid overfilling Overfilling reduces performance and causes clogging of hose blower and deck 2 Turn blades off Drive machine to location the clippings are to be dumped DO NOT operate blades in reverse If you must back machine to dump clippings in desired location LOOK and SEE behind and down for children pets and hazards before and while backing 3 Stop motion of machine by returning Motion Control s to Neutral N Set Park Brake Stop engine 4 Unlatch cover and lift Remove bags and dump debris in desired location 5 After dumping to maintain peak performance check the catcher screen located on the inside of the Cover Assembly to make sure it is clean and free of any build up Clean as required with brush or broom Close catcher cover and latch Re start engine and drive machine to cutting area Set engine speed to highest setting engage blades and resume operation PEO WARNING DO NOT attempt to remove any clogs from deck blow er or hose with engine or blade running STOP engine STOP blades Set brake Remove key Make sure blades and all rotating components have come to a complete stop before removing any catcher or unclog ging any catcher component IF THE GRASS CATCHER BECOMES CLOGGED The grass catcher may become plugged if the conditions are too severe the catcher is overfilled or the machine is used improperly If plugging does occur attempt th
4. HZT Operator s Manual for blade wear limits and sharpening replacement instruc tions Blower Check blower impeller blower housing and inlet outlets for signs of wear and deterioration Replace as needed Check all fasteners and hardware to insure none are missing and all are tightened securely Lubricate impeller shaft bearings with 1 to 3 shots of General Purpose grease from a grease gun Belts Check belts for wear and fraying Replace as needed Idler Arm Check idler arm to insure it pivots freely and bushings are not worn Replace worn bushings as needed A Grass Catcher bags used on SNAPPER products are made of woven fab ric and are subject to deterioration and wear during normal usage Check condition of bags before each use Immediately replace worn or damaged catcher bags with only bags recommended by SNAPPER The Grass Catcher is optional equipment on some models 11 gt SNAPPER cdi Z VAC Sn So BLOWER UNIT GROUP 25 CZT HZT Models i 28 Ss 26 Grease Fitting Orientation 12 z 3 OANDOARWDND Part No 3046782 91121 90183 3021097 44995 91804 14409 10776 3046824 91527 3047253 91601 91218 3046781 3046853 91541 3022832 90839 3031920 3046854 3031919 90613 3046813 3043613 90122 91560 91518 91305 92111 91541 Qty WOW A YO MND A BOD CF a ANN Aa A a unit breakdow Snapper Z Vac Blower Unit Group CZT HZT Models Description
5. weld them Keep hands and feet away from moving parts Frequently check components and replace with manufac turer s recommended parts when necessary Use only factory authorized replacement parts when mak ing repairs Always comply with factory specifications on all settings and adjustments Only authorized service locations should be utilized for major service and repair requirements Never attempt to make major repairs on this unit unless you have been properly trained Improper service proce dures can result in hazardous operation equipment dam age and voiding of manufacturer s warranty BLOWER KIT INSTALLATION STEP 1 Remove pin rod and spring securing dis charge deflector to mower deck and remove deflector Store deflector for future use IMPOR TANT Never operate any mower without a dis charge deflector or grass catcher securely in place STEP 2 Remove two bolts securing right deck pul ley guard to mower deck and remove guard Set bolts aside for future assembly step Store guard for future use IMPORTANT Never operate any mower without a pulley guard securely in place STEP 3 Loosen both nuts all the way to end of rod NOTE Deck belt tension rod is located under foor rest of machine Removing foot rest will aid in accessing rod STEP 4 Remove belt from right deck pulley Remove nut securing pulley to blade spindle and remove pulley replacing with supplied replace ment pulley Replac
6. 3 8 16 x 1 Hex Head Cap GR5 NUT 3 8 16 Hex Flange Lock WELDMENT T Handle Pin SCREW 5 16 18 x 1 1 4 Hex Head Cap GR5 NUT 5 16 18 Hex Flange Lock NUT 5 16 18 Hex Large Flange Center Lock SPRING Idler Fast Vac KEY 1 4 Square x 1 44 SCREW 3 8 16 x 6 Hex Head Cap GR5 15 SNAPPER Z VAC CATCHER GROUP CZT HZT Models 25 16 Item OAOANDOOARWDND Part No 3046861 1704033 1704180 1704405 1667248 1910531 90922 91702 3021670 90376 3022838 0960367 1703700 1704057 91578 1675707 1703807 90316 1703855 3000847 1672023 90187 91511 3022875 3022833 3022876 91757 91290 15067 1703822 91530 91084 1704507 91702 3046722 90598 91603 90883 91241 1704075 3046774 1704508 1960400 90052 1705876 1933886 Qty 2233330090003 BAB AND OAD BAB SB BAA PRBM YM DYMO BMD A A AND A OA Ww A BRO AD Snapper Z Vac Catcher Group CZT HZT Models Description ASSEMBLY 2 Bag Cover and Screen includes Item No 1a 5 12 13 14 42 43 44 45 CATCHER TOP 2 Bag WINDOW Cover DECAL Safety Grass Bag CLIP Canoe WASHER 188 Rivet SCREW 10 32 x 1 1 2 Hex Washer Head Machine w Nylon Patch WASHER 19 x 38 x 06 Flat STRAP Rubber NUT 10 32 Hex Nyloc KNOB PIN Round Head SCREEN SEAL Clip POP RIVET 3 16 x 265 Alum TUBE CLIP Grass Bag HANGER Grass Bag BOLT 5 16 18 x 3 4 Square Neck Carriage GR5 HOOP Grass Bag GRASS BAG CLAMP G
7. ECTOR Not Shown MUFFLER CLAMP Not Shown 19 an 5 list Place Against Front of Footrest para A Slide Through ci Opening in Er a Footrest s o k n SNAPPER m Je E 4 5 oe 5 Z VAC WEIGHT BAR GROUP CZT HZT Models unit b Snapper Z Vac Weight Bar Group CZT HZT Models Part No Qty Description 78288 5 WEIGHT 27 x 5 x 1 4 78289 4 WEIGHT 27 x 2 1 2 x 1 4 91821 2 BOLT 1 2 13 x 3 Hex Head 90254 2 WASHER 1 2 Split Lock 91316 2 NUT 1 2 13 Hex 21 VAC by GIANT VAC A WARNING Do not open cover with engine running Do not operate mower without the canpa as catcher In place e 1 rating on slopes refer to Hoteles s manual for counterwelghts NOTE Decals are not to scale 22 unit h Snapper Z Vac Decal Group CZT HZT Models Item Part No Qty Description 1 3046944 1 DECAL Fast Vac 2 1704405 1 DECAL Safety Grass Bag 3 3046850 1 DECAL Danger Fast Vac 4 3046851 1 DECAL Warning Fast Vac 5 3046883 1 DECAL Warning Fast Vac 23 2 YEAR LIMITED WARRANTY For two 2 years from purchase date for the original purchaser s residential non commercial use SNAPPER through any authorized SNAPPER dealer will replace free of charge except for taxes where applicable any part or parts found upon examination by the factory at McDonough Georgia to be defective in material or workmanship or both For one 1 year from purchase date for
8. GGER FRAME ONTO BUMPER MOUNT PLATE PINS STEP 14 Install cross assembly onto bagger frame with four 3 8 16 x 3 4 bolts and hex flange lock nuts tightening securely Insert bolts back through bagger frame and into cross assembly STEP 15 Insert two 5 16 18 x 3 4 bolts through reinforcement plate not shown refer to Parts List Catcher Mount Group then through holes in bagger frame Install cover latch arm onto bolts and secure with hex flange lock nuts tightening INSTALL REINFORCEMENT securely NOTE Use the leftmost set of holes in PLATE ON BACK SIDE OF the bagger frame when installing arm BAGGER FRAME Z STEP 16 Lay cover assembly on cross assembly Align hinges on cross assembly with hinges on cover and install one round head pin through each set of hinge holes securing with a hair pin STEP 17 Slip looped end of cover support cord onto threaded stud on hose adapter assembly Secure end of cord with one 3 16 flat washer and 10 32 nyloc nut not shown Run nut all the way in on thread but leave cord loose enough to swivel STEP 18 Install bags onto cross assembly by hooking slot in bag hanger onto tabs in channel assembly STEP 19 Close cover and lock in place by hook ing lock knob into slot in cover latch arm STEP 20 Slip one hose clamp onto each end of hose use the clamp with the black quick release knob at the blower end and install hose between blower and bagger Make sure to fit hoses fir
9. McDonough Georgia 30253 24 25 26 27 SMAPPER ASSEMBLY INSTRUCTIONS OPERATOR S MANUAL PARTS LIST P Z VAC Grass Catcher Kit for CZT HZT Series 0 SMA j ER McDonough GA 30253 U S A Manual No 7100056 I R 03 31 05
10. NT Never oper ate any mower without a pulley guard securely in place STEP 7 Slip tube of locking pin bracket into blow er mount and secure with T handle pin making sure pin goes through both upper and lower part of blower mount Then align base of pin bracket par allel with rear of deck and using bracket as a tem plate drill two 7 16 holes through deck Insert two 3 8 16 x 1 bolts up through deck and bracket securing with hex flange nuts Tighten securely IMPORTANT Use gloves when working under deck Sharp blades can cause injury STEP 8 Lay supplied pulley guard onto deck Align hole in front flange with front mounting hole in deck and secure with one of the two bolts securing original guard Do not tighten yet Align side flange of guard with side of deck and using other hole in guard as a template drill one 9 32 hole in deck and install other bolt NOTE Bolt is self tapping Tighten both bolts securely STEP 9 Install belt guard between pulley guard and belt guard support clip on front part of blower mount Secure with two 5 16 nylon wing nuts Tighten nuts securely ld Br NL A INSTALL BELT GUARD 54 AND SECURE WITH SV WING NUTS 7 A WEIGHT KIT INSTALLATION Warning Weight kit must be installed prior to installing bagger unit Failure to do so may 4 NARROW BARS result in longitudal tipping of unit THROUGH FOOTREST gt STEP 10 Insert the four narrow weight bars through openin
11. SMAPPER ASSEMBLY INSTRUCTIONS OPERATOR S MANUAL PARTS LIST VAC Grass Catcher Kit for CZT HZT Series 0 Models covered Blower Kit P N 7078273 Bagger Kit P N 0 50576 Weight Kit P N 7078274 Actual product may differ from product pictured above Complete Kit P N 7063375 Manual No 7100056 I R 03 31 05 Congratulations You have just purchased one of the finest pieces of outdoor power equipment on the market today If properly cared for your new Z Vac Grass Catcher Kit will provide years of dependable service Please read and follow this instruction man ual carefully in order to get the most out of your new equipment As you carefully unpack your unit you will find the following items 1 Blower Kit 1 Bagger Kit 1 Weight Kit 1 Package containing operating manuals and warranty registration Each product leaves our factory in excellent condition occasionally however some damage may occur during shipment If any such damage is found upon initial inspection immediately notify the transport carrier who delivered your machine as they are solely responsible for such damage as well as any subsequent adjustments necessary Before assembly please take a moment and record your model number and serial number below for future reference both numbers are located on the serial tag attached to the blower Model number Serial number Also be sure to promptly fill out and return the warranty registration enclos
12. e follow ing 1 Engine speed too slow set engine speed control to FAST position Empty catcher bags more often Clean screen on cover assembly Ground speed too fast cut at slower speed Removing too much grass raise cutting height cut partial width and cut lawn more frequently Grass is too wet from rain or dew allow grass to dry Blades are dull or worn inspect blades and replace as necessary Use only genuine SNAPPER replacement blades 8 Deck blower or hose has clipping build up clean all clippings from all internal surfaces WARNING A 2 4 N No DO NOT put fingers or hands inside blower STOP blades STOP engine Remove key Use only a stick or other suitable means to clear the blower of clogs or other obstructions WARNING DO NOT attempt any adjustments maintenance or repairs with engine running STOP blades STOP engine Remove key WARNING Grass Catcher components are subject to deteriora tion Inspect frequently Replace worn or damaged components immediately Use only genuine SNAPPER replacement parts Continued On Next Page 10 IF THE GRASS CATCHER BECOMES CLOGGED Continued From Previous Page To Clear A Plugged Hose 1 2 Stop blades Stop engine Remove key After all rotating components engine blower blades have come to a complete stop loosen hose clamp at outlet of blower and remove hose from blower Clear any obstructions fr
13. e nut and torque to 70 80 ft lbs NOTE Nut secures blade bolt in place Support bolt from beneath while replacing pulley IMPORTANT Use gloves when working under deck Sharp blades can cause injury Replace deck belt onto bottom groove of pulley With deck in lowest cutting position retighten nuts on deck tension rod until spring length measures 2 5 16 STEP 5 Set blower against deck discharge Align holes in blower mount with holes in deck discharge tabs and secure with rod and pin removed in Step 1 NOTE Do not include deflector spring in rod installation STEP 6 Pull back on idler tension release handle and install blower belt around top groove of deck pulley NOTE Make sure belt is not rolled or twisted when installing REMOVE PULLEY p gt GUARD y 5 A SL 00SEN NUTS TO 7 EEND OF ROD x gt E 5 an EZ WHEN RETIGHTENING NUTS f W ADJUST UNTIL SPRING LENGTH MEASURES 2 5 16 REPLACEMENT PULLEY _ i a 2 y fi gt A a INSTALL BLOWER AND FROM UPPER SECURE WITH ROD AND PIN IDLER PULLEY r7 a x SESITO LOWER EY IDLER PULLEY A N REMOVE BOLTS THEN REMOVE COVER CHECK TO SEE A THAT BELT IS HON PULLEYS STEP 6a Remove bolts securing impeller pulley cover to blower and remove cover STEP 6b Check to see that blower belt is routed around impeller pulley and idler pulleys after belt is installed onto deck pulley Then replace cover Tighten bolts securely IMPORTA
14. e the engine governor setting or over speed the engine Stop on level ground shut off engine before leaving the operator s position for any reason Stop equipment and inspect impeller blades after striking objects or abnormal vibration occurs Make necessary repairs before resuming operations Keep hands and feet away intake and discharge areas Keep pets and bystanders away Do not operate the unit while under the influence of alco hol or drugs Use caution when crossing roads and sidewalks Stop engine if not blowing Use care when loading or unloading the machine into a trailer or truck Use care when approaching blind corners shrubs trees or other objects that may obscure vision SLOPE OPERATION Slopes are a major factor related to loss of control and tip over accidents which can result in severe injury or death All slopes require extra caution If you cannot back up the slope or if you feel uneasy on it do not drive on it Do Mow up and down slopes never across face Remove obstacles such as rocks tree limbs etc Watch for holes ruts or bumps Uneven terrain could overturn the unit Tall grass can hide obstacles Keep all movement on the slopes slow and gradual Do not make sudden changes in speed or direction Do Not Do not start or stop on a slope If tires lose traction pro ceed slowly straight down the slope Do not turn on slopes unless necessary and then t
15. ed in your manual packet Your new unit requires very little assembly Simply follow the instructions contained within this manual to begin enjoying the benefits of your new unit Safety rules regarding outdoor powe IMPORTANT READ CAREFULLY THE FOLLOWING SAFETY RULES BEFORE ASSEMBLING OR OPERATING UNIT TRAINING Read understand and follow all instructions in the man ual and on the unit before starting If the operator s or mechanic s can not read English it is the owner s responsi bility to explain this material to them Become familiar with the safe operation of the equipment operator controls and safety signs All operators and mechanics should be trained The owner is responsible for training the users Only allow responsible adults who are familiar with the instructions to operate the unit Never let children or untrained people operate or service the equipment Local regulations may restrict the age of the operator The owner user can prevent and is responsible for acci dents or injuries occurring to themselves other people or property PREPARATION Evaluate the terrain to determine what accessories and attachments are needed to properly and safely perform the job Use only accessories and attachments approved by the manufacturer Wear appropriate clothing including safety shoes safety glasses and ear protection Long hair loose clothing or jew elry may get tangled in moving parts
16. g in side of foot rest Be sure holes in weights are all aligned Next insert the two 1 2 Y ot J 13 x 5 bolts through the five wide weight bars and hs A 5 WIDE BARS lay the wide bars against front of footrest inserting o EAN AGAINST bolts through holes in narrow bars Secure with EA FOOTREST 1 2 split lock washers and nuts Tighten securely BAGGER KIT INSTALLATION VE STEP 11 Install bumper mount standoffs onto rear PEE bumper of machine utilizing existing hardware on i N machine NOTE Invert hardware when installing E standoffs installing bolts out through bumper with nuts facing out NOTE When installing standoffs be sure that the bumper mount plate mounting holes along the back bar of the standoffs are located towards the right side of the machine Refer to the Parts List section of the manual STEP 12 Install bumper mount plate onto stand offs with four 5 16 18 x 3 4 hex cap screws secur ing with four 5 16 18 flange lock nuts Tighten securely Also install muffler deflector see inset onto muf fler making sure deflector directs exhaust off to the side of the mower Fasten with clamp IMPORTANT FAILURE TO INSTALL MUFFLER DEFLECTOR MAY RESULT IN A FIRE E STEP 13 Hook bottom of bagger frame onto pins J SLIDE ROD in bottom of bumper mount plate Then slide lock THROUGH 3 ing rod through aligned holes in bagger frame and Pr HOLES 1 bumper mount plate securing with bridge pin HOOK BA
17. mly onto adapters Tighten clamps securely SLIP SLOT IN GRASS BAG HANGER ONTO TAB ON CROSS ASSEMBLY EAN amp maintenance INTRODUCTION Follow operation and maintenance instructions in the Operator s Manual provided with the Snapper CZT HZT GRASS CATCHER OPERATION 1 Select desired cutting height Choose a setting that will not attempt to cut off too much at once overloading the machine 2 After starting engine and allowing a brief warm up peri od move engine speed control to highest setting 3 Drive machine to cutting area Engage blades 4 Select a slow forward ground speed until familiar with conditions Do not select a speed that is too fast caus ing the machine to become overloaded 5 The weight of the grass catcher and contents will affect the stability and handling of the machine Avoid sudden starts and sharp turns Reduce speed on slopes and DO NOT operate machine on slopes exceeding 10 degrees 18 grade Operate machine up and down slopes DO NOT operate machine across the face of slopes Turn blades off when traveling up slope 6 Empty grass catcher bags often to minimize effect on stability and handling Over filling the catcher bags will reduce performance and cause clogging of the hose blower and deck 7 Do not operate the machine with the Grass Catcher cover open The entire Grass Catcher must be installed the cover closed and latched properly before operating EMPTYING GRASS CATCHER
18. om hose If necessary use a stick to reach into the hose Reinstall hose to blower and securely tighten hose clamp To Clear A Plugged Blower 1 2 3 4 5 Stop blades and blower Stop engine Remove key After all rotating components have come to a complete stop loosen the hose clamp at the outlet of the blower Remove hose from blower Using a stick or similar object clear all obstructions from blower DO NOT INSERT HAND Reinstall hose to blower and securely tighten hose clamp GRASS CATCHER MAINTENANCE Grass Catcher components are subject to wear and deteri oration during normal usage Inspect all components fre quently for signs of wear and deterioration Replace worn or damaged components immediately BEFORE EACH USE 1 Perform pre start checklist and maintenance as instructed in the SNAPPER CZT HZT Operator s Manual and Engine Owner s Manual included with the machine WARNING Catcher Inspect all catcher components Replace all worn or damaged parts Catcher Bags Check bags often for wear or damage Replace worn or damaged bags immediately using only SNAPPER approved replacement bags Deck Blower Hose Clean grass build up from deck blower hose covers and rear cover screen To maintain peak performance make sure screen is clean at each dumping Hose Check hose for wear tears and holes Replace as needed Blades Check blades for sharpness wear flatness and damage Refer to CZT
19. rass Bag WASHER 5 16 Split Lock NUT 5 16 18 Hex GR5 or B HOSE CLAMP Upper HOSE Snapper Fast Vac HOSE CLAMP Lower Fast Vac SCREW 10 24 x 1 1 4 Hex Head Cap GR5 NUT 10 24 Hex Nyloc HAIR PIN 1 6 CROSS ASSEMBLY BOLT 1 4 20 x 3 4 Carriage SCREW 1 4 20 x 3 8 Hex Washer Self Tap STRAP Tube Support WASHER 191 I D Flat WELDMENT Hose Adapter Deflector WASHER 1 4 Flat NUT 1 4 20 Hex Nyloc SCREW 10F x 7 8 Pan Head Cross Recess POP RIVET 3 16 SUPPORT Tube SEAL 2 Bag Catcher BRACKET Seal SCREW 10 12 x 5 8 Hex Washer Self Tap WASHER 1 4 Split Lock CABLE Double Loop NUT Speed 17 See Catcher Group Fastens to Rear Bumper Assembly of Mower Using Existing Bumper Hardware SNAPPER Z VAC CATCHER MOUNT GROUP CZT HZT Models 18 z 3 DASS En u RIES Part No 3046687 91086 91619 3046831 3046829 91318 91601 3046995 50551 91318 91601 3046693 15067 3039122 3039123 Qty Aa 3 BB BP P PPh AH A AB oa Snapper Z Vac Catcher Mount Group CZT HZT Models Description WELDMENT Bagger Mount Frame SCREW 3 8 16 x 3 4 Hex Head Cap GR5 NUT 3 8 16 Hex Flange Lock ARM Cover Latch REINFORCEMENT PLATE SCREW 5 16 18 x 3 4 Hex Head Cap GR5 NUT 5 16 18 Hex Flange Lock WELDMENT Bumper Mounting Plate STANDOFF Bumper Mount SCREW 5 16 18 x 3 4 Hex Head Cap NUT 5 16 18 Hex Flange Lock ROD Support HAIRPIN Clip EXHAUST DEFL
20. t Emissions Durability Period and Air Index information on the engine emissions label MAINTENANCE AND STORAGE Always observe safe refueling and fuel handling practices when refueling the unit after transportation or storage Always follow the engine manual instructions for storage preparations before storing the unit for both short and long term periods Always follow the engine manual instructions for proper start up procedures when returning the unit to service Never store the machine or fuel container inside where there is an open flame such as in a water heater Allow unit egarding outdoor power equipment to cool before storing Shut off fuel while storing or transporting Do not store fuel near flames or drain indoors Keep all hardware tight and keep all parts in good work ing condition Replace all worn or damaged decals Never tamper with safety devices Check their proper operation regularly Clean leaves and debris from mufflers and engine to pre vent fires Clean up oil or fuel spillage Stop and inspect the equipment if you strike an object Repair if necessary before restarting Never make adjustments or repairs with the engine run ning unless specified otherwise Park machine on level ground Never allow untrained per sonnel to service machine Carefully release pressure from components with stored energy g springs Only replace impellers Never straighten or
21. the battery or machine caused by neglect or abuse destruction by fire explosion freezing overcharging improper maintenance or use of improper electrolyte There is no other express warranty DISCLAIMER OF WARRANTY Implied warranties including those of merchantability and fitness for a particular purpose are limited to two 2 years from purchase date for the original purchaser s residential or other non commercial use and one 1 year from purchase for the original purchaser s commercial non residential use and ninety 90 days from purchase for the original purchaser s rental use and to the extent permitted by law any and all implied warranties are excluded This is the exclusive remedy Liabilities for consequential damages under any and all warranties are excluded Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state WARNING THE USE OF REPLACEMENT PARTS OTHER THAN GENUINE SNAPPER PARTS MAY IMPAIR THE SAFETY OF SNAPPER PRODUCTS AND WILL VOID ANY LIABILITY AND WARRANTY BY SNAPPER ASSOCIATED WITH THE USE OF SUCH PARTS IMPORTANT Please fill out the SNAPPER Product Registration Card immediately and mail to Snapper s Product Registration Center P O Box 1379
22. the original purchaser s commercial non residential use SNAPPER through any authorized SNAPPER dealer will replace free of charge any part or parts found upon examination by the factory at McDonough Georgia to be defective in material or workmanship or both For ninety 90 days from purchase date for the original purchaser s rental use SNAPPER through any authorized SNAP PER dealer will replace free of charge any part or parts found upon examination by the factory at McDonough Georgia to be defective in material or workmanship or both All transportation costs incurred by the purchaser in submitting material to an authorized SNAPPER dealer for replace ment under this warranty must be paid by the purchaser This warranty does not apply to certain transmissions to engines and their components and batteries as these items are warranted separately This warranty does not apply to parts that have been damaged by accident alteration abuse improper lubrication normal wear or other cause beyond the control of SNAPPER This warranty does not cover any machine or component part that has been altered or modified changing safety performance or durability Batteries have a one 1 year warranty period with free replacement if required for one 1 year from the original purchase date SNAPPER will not be responsible for any installation cost incurred The battery warranty only covers original equip ment batteries and does not cover damage to
23. urn slowly and gradually downhill if possible Do not use near drop offs ditches or embankments The operator could lose footing or balance or blower could sud denly turn over if a wheel is over the edge of a cliff or ditch or if an edge caves in Do not operate on slopes with wet grass Reduced foot ing or traction could cause sliding Do not operate machine on slopes in excess of 10 degrees 18 grade when equiped with a grass catcher Do not operate machine without weight kit installed when equiped with a grass catcher CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children Children are often attracted to the unit and its activity Never assume that children will remain where you last saw them Keep children out of the mowing area and under the watchful care of another responsible adult Do not allow children or others to ride on the machine attachment or towed equipment even with the blades off Be alert and turn unit off if children enter the area Before and during reverse operation look behind and down for small children Never allow children to operate the unit Use extra care when approaching blind corners shrubs trees or other objects that may obscure vision EMISSIONS Engine exhaust from this product contains chemicals known in certain quantities to cause cancer birth defects or other reproductive harm Look for the relevan
Download Pdf Manuals
Related Search