Smart Technologies UF75 Projector User Manual
Contents
1. e Rotate the projector to the right to increase the right image size decrease the left image size and move the entire image to the right e Rotate the projector to the left to decrease right image size increase the left image size and move the entire image to the left To center the projected image To reset the lamp timer 10 KNOWLEDGE BASE MAINTAINING YOUR SMART UF75 PROJECTOR If the image is off center use a wrench to turn the adjustment screw on the mounting base e Rotate the adjustment screw clockwise to move the entire image to the left e Rotate the adjustment screw counterclockwise to move the entire image to the right Resetting the lamp timer After you replace the lamp access the projector service menu to reset the lamp hour counter To prevent accidental errors only a system administrator should perform this procedure D CAUTIONS Always reset the lamp hours after you replace the lamp because lamp service reminders are based on the current hours of use e Do not adjust any settings in the service menu other than those listed in this guide Changing other settings can damage or affect the operation of your projector and invalidates your warranty 1 Press the remote control buttons quickly in teh following sequence to access the service menu Down Up Up Left Up 2 Scroll2. made simple SMART 2 KNOWLEDGE BASE MAINTAINING YOUR SMART UF75 PROJECTOR IMPORTANT When cleaning the interactive whiteboard system Wipe the exterior of the projector with a lint free cloth If necessary use a soft cloth moistened with a mild detergent to clean the projector housing For optimum performance clean the projector every 12 months Increase this frequency according to environmental conditions Do not use abrasive cleaners waxes or solvents When cleaning the projector s mirror Use a bellows bulb or air blower bulb commonly found in audio visual supply stores to blow off dust Never touch the mirror or lens with your bare hands or a brush If wiping the mirror or lens is unavoidable wear protective gloves and gather the supplied cleaning cloth into a ball Gently run the cleaning cloth across the mirror from the center to the edge using the cleaning cloth like you would a feather duster When cleaning the projector s lens Never touch the lens with your bare hands or a brush If wiping the lens is unavoidable wear protective gloves and gather the supplied cleaning cloth into a ball Gently run the cleaning cloth across the lens from the center to the edge using the cleaning cloth like you would a feather duster Removing and replacing the projector lamp module When the lamp reaches the end of its life a message appears reminding you to replace the lamp Make sure you have a replacemen
3. PLEASE THINK BEFORE YOU PRINT Knowledge base Maintaining your SMART UF 5 projector Maintaining your interactive whiteboard For information on maintaining your interactive whiteboard see your SMART Board interactive whiteboard user s guide smarttech com support Cleaning the projector N WARNING Cleaning a wall mounted projector can result in a fall or injury Use caution when climbing a ladder and consider removing the projector from its wall mounting bracket to clean it or to replace the projector lamp M CAUTIONS e Never touch the mirror with your hands or a brush and do not scrub the surface of the mirror with the supplied cleaning cloth Instead use the supplied cleaning cloth to clean the mirror gently and do not put any cleaning solvents on the cloth or the mirror e Before you clean the projector press the Power button twice on the Extended Control Panel ECP or remote control to put the system into Standby mode and then allow the lamp to cool for at least 30 minutes e Do not spray cleaners solvents or compressed air directly on the projector Do not use spray cleaners or solvents near any part of the projector because they can damage or stain the unit Spraying the system could spread a chemical mist on some of the projector s components and lamp resulting in damage and poor image quality e Do not allow liquids or commercial solvents of any kind to flow into the projector base or head Extraordinary
4. a soft bristle attachment to gently clean the area being careful not to touch any optical components To install the new lamp 1 Remove the new lamp module from its packaging 2 Carefully place the lamp module into the projector by holding the lamp module by the handle vertically and guiding it into its slot 3 Gently press the power end of the lamp module against the projector to ensure the power plug makes contact with the projector s power receptacle To complete the projector lamp installation To install the filter KNOWLEDGE BASE MAINTAINING YOUR SMART UF75 PROJECTOR fj NOTE You should be able to place the lamp module into the projector easily without applying much force 4 Use the Phillips screwdriver to tighten the captive screws 5 Carefully replace the lamp cover 6 Connect the power cable 7 Press the Power button once on the remote control or the ECP to confirm that the projector is operating and that the lamp module is correctly installed 1 Turn on the projector Adjust the projector image if necessary 3 Access the service menu to reset the lamp hour counter See Resetting the lamp timer in your SMART Board interactive whiteboard system user s guide smarttech com support 4 Activate the projector s alert e mails and lamp warnings if they ve been deactivated See the appropriate sections in your SMART Board interactive whiteboard system user s guide sm
5. arttech com support Installing and removing the filter For optimum performance replace the projector filter every 12 months Increase this frequency according to environmental conditions 1 Place the filter on left side of the projector 7 KNOWLEDGE BASE MAINTAINING YOUR SMART UF75 PROJECTOR To remove the filter 1 Insert a flat head screwdriver under the center tab and gently pry up one end first and then the other end Focusing and adjusting the projected image You can use any or all of these adjustments to refine the image Adjust each setting a little at a time To focus the projector Move the focus adjustment lever up or down until the image is clear image To adjust the projector 1 image 8 KNOWLEDGE BASE MAINTAINING YOUR SMART UF75 PROJECTOR 2 Square the top edge of the projected image with the top edge of the interactive whiteboard s bezel or frame by moving the projector manually gt aaa or frame Fill as much of the screen as possible aligning the top of the projected image i projected with the top of the bezel or frame it image TIP Move the focus lever until it is almost in the locked position the friction will help to maintain control when you re moving the projector to the desired position 3 Move the lever to the right to lock the projector 4 Using a Phillips screwdri
6. s approved by SMART Technologies Contact your authorized SMART reseller smarttech com where for replacement parts Never replace the lamp module with a previously used lamp module Always handle the fragile lamp module with care to prevent premature lamp failure or exposure to mercury Use gloves when touching the lamp Do not touch the lamp with your fingers Recycle or dispose of the lamp as hazardous waste in accordance with local regulations You need a Phillips No 2 screwdriver and a flat screwdriver to complete these procedures 1 Press the Power button twice on the remote control or the ECP to put the projector into Standby mode Wait at least 30 minutes for the projector to cool down Disconnect the power cable from the projector 4 KNOWLEDGE BASE MAINTAINING YOUR SMART UF75 PROJECTOR Lamp cover g TIP If the cover is difficult to remove insert a flat screwdriver or small coin into the slot on the bottom of the lamp cover to gently pry the cover open 5 Use a Phillips screwdriver to loosen the two captive screws from the bottom of the lamp module g TIP Loosen the captive screws Don t remove them 6 Use the handle on the bottom of the lamp module to slide out the lamp and remove it from the projector 7 Put the old lamp in a secure container and handle it gently until you recycle it 5 KNOWLEDGE BASE MAINTAINING YOUR SMART UF75 PROJECTOR 8 Use a vacuum with
7. t projector lamp before proceeding with the following instructions al WARNINGS Replace the lamp when the projector displays its lamp life warning message If you continue to use the projector after this message appears the lamp can shatter or burst scattering glass throughout the projector If the lamp shatters or bursts leave and then ventilate the area Do not touch the glass fragments because they can cause injury Wash your hands thoroughly if you have come into contact with lamp debris To remove the old lamp KNOWLEDGE BASE MAINTAINING YOUR SMART UF75 PROJECTOR e Once the area has been ventilated thoroughly clean the area around the projector and discard any edible items placed in that area because they could be contaminated e Call your authorized SMART reseller smarttech com where for instructions Do not attempt to replace the lamp e Uncovering the lamp while the projector is mounted on the wall mounting bracket can lead to product damage or personal injury from falling pieces of glass if the lamp is broken e When replacing the projector lamp Put the projector into Standby mode and wait 30 minutes for the lamp to cool completely Donot remove any screws other than those specified in the lamp replacement instructions Wear protective eyewear while changing the lamp Failure to do so can cause injuries including loss of eyesight if the lamp shatters or bursts Use only replacement lamp
8. to Lamp Hour Reset and then press OK Both Lamp Hour values Standard and Economy are reset to zero M CAUTION Do not use the Lamp Hour Reset feature unless you have just replaced the lamp Resetting the lamp hour counter on an old lamp can rsult in lamp failure and projector damage fj NOTE You re unable to reset the Display Hours value because it s the running total of hours the projector has been in use 3 Press the Menu button on the remote control 11 KNOWLEDGE BASE MAINTAINING YOUR SMART UF75 PROJECTOR The SMART UF75 Settings menu appears 4 Select to confirm that the lamp hours are reset to zero www smarttech com support www smarttech com contactsupport EN 2011 SMART Technologies ULC All rights reserved SMART Board smarttech the SMART logo and all SMART taglines are trademarks or registered trademarks of SMART Technologies ULC in the U S and or other countries All third party product and company names may be trademarks of their respective owners Contents are subject to change without notice 05 2011
9. ver loosen the four side screws and then move the projector backward or forward on the boom until the top of the image fills the interactive whiteboard from edge to edge g TIP Tighten the screws in the order shown while holding the projector steady with one hand to minimize movement 9 KNOWLEDGE BASE MAINTAINING YOUR SMART UF75 PROJECTOR To adjust the vertical keystone of the projected image Loosen or tighten the lower screws on the projector mounting plate turning each screw equally a quarter or half turn at a time e Turn the adjustment screws clockwise to push the projector up increase the image width at the bottom and move the bottom of the image down e Turn the adjustment screws counterclockwise to push the projector down decrease the image width at the bottom and move the bottom of the image up i NOTE The top of the image moves very little from its position To adjust the horizontal keystone of the projected image Turn the projector to the left or right to adjust the image g TIP Move the focus lever until it is almost in the locked position the friction will help to maintain control when you re moving the projector to the desired position
Download Pdf Manuals
Related Search