Home

Singer 9910 Sewing Machine User Manual

1. As D INSERTING THE BOBBIN Place bobbin into bobbin holder with the thread N gt NOTE Use Singer bobbins only Draw thread into notch a while holding the Pull thread toward the left and along the inside Pull thread out about 10 cm 4 inches unwinding counter clockwise bobbin of spring b until it slips into notch c making sure that thread does not slip out of notch a Replace the bobbin cover Set the left tab into the hole in needle plate and push the right side of bobbin cover down until it clicks into place THREADING THE MACHINE A PREPARING TO THREAD MACHINE 1 Raise the presser foot lifter 2 Press the needle up down button and set the needle in up position Keep this position until needle eye threading B SETTING SPOOL OF THREAD ON SPOOL PIN 1 Pull up the left end of spool pin and set the spool of thread on spool pin so that the thread unrolls from the front of the spool 2 Set the spool cap on spool pin as far as it will go a Reverse spool cap direction according to the size of spool b Use the small spool cap when you use cross wound thread Leave
2. Acaurion To prevent accidents If you did not switch to twin needle mode needle may hit the needle plate and break 8 Always test sew selected stitch Note Some stitches look better than others sewn with a twin needle 9 Sew project Twin needle mode will remain until you press the twin needle button again or turn off the machine Note Twin needle sewing may be used with decorative amp letter stitch patterns by pressing twin needle button Twin needle icon will appear on the LCD DECORATIVE amp LETTER STITCH SEWING You can combine decorative amp letter stitches into a string by selecting each pattern A SELECTING DECORATIVE amp LETTER STITCH selecting mode 1 Press the decorative amp letter stitch button First 5 patterns of decorative patterns will be indicated on the lower line of LCD 2 By pressing the decorative amp letter stitch button selecting group will change as below Decorative pattern Gothic letter stitch Script letter stitch Italic letter stitch Outline letter stitch Russian letter stitch m gt oOaQ00 9 3 After you select the group press the scroll down button Next 5 patterns of selected group will appear By pressing the scroll up or down button you can scroll up or down in increments of 5 patterns 4 To select a pattern press the
3. Tea X li E a 200 u puto J A A A A F1l F3 F4 F5 _ alli In 1 2 4 5 v qao EDT C m 14 4 rl e ff zz 38 47 H SEWING THE SELECTED PATTERNS a Single sewing You can combine the tack stitch by pressing the tack button at selecting mode When you combined the tack stitch or letter stitch at the end of pattern machine will stop automatically after sewing selected patterns b Repeat sewing The pattern combination will sew repeatedly without combining the tack stitch at the end of the pattern sequence SEWING 1 Attach the satin foot when sewing decorative amp letter stitch 2 Machine will start sewing from highlighted pattern You must shift the cursor to the pattern you where you wish to start sewing When the I mark cursor is indicated on the right side of selected patterns machine will start from first pattern 3 Lower the presser foot and start sewing Machine will indicate the sewing pattern on the top left side of LCD I TO SEW PATTERN FROM BEGINNING a When you stop sewing at the middle of selected patterns LCD will indicate the setting of sewing second line
4. ico N Ko Ks DER Eh COG Description of Chart Symbols ik Mirror Stitch possible Reverse Stitch possible 4 Mirror and Reverse stitches possible X2 Elongation possible IY lw gt cl mm 5 Aja sir ko ko N ko 79 ko ko D ko E ko co ko ko NSS SA Ske MN RI 101 102 103 104 105 106 107 108 109 110 Mz Mz Mz 25 24 STRAIGHT STITCH SEWING Straight stitch patterns should be selected to suit the type of fabric being sewn Left needle position No 2 is most suited for sewing light weight fabrics No 1 Center needle Position No 2 Left needle Position No 3 Center needle with built in reverse stitch No 4 Left needle with built in reverse stitch General Purpose Foot A A Straight Stitch 1 Position the fabric under the presser foot and lower it 2 Hold the upper thread and bobbin thread loosely and start sewing Place hand lightly on the fabric while sewing 3 When you reach the end of seam stop sewing 4 Press the thread cutter button B Straight Stitch With Auto lock Stitch Pattern No 3 4 1 Position the fabric under the presser foot and lower it 2 Hold the upper thread and bobbin thread loosely and start sewing Machine will sew 4 5 stitches forward and sew 4 5 stitches backward and continue sewing forward 3 When you reach the end of
5. 21 ADJUSTING THE FORWARD AND REVERSE STITCHES 49 SELECTING UTILITY STITCH PATTERN 22 MAINTENANCE esee 50 A DIRECT STITCH PATTERN es 122 I GUEANING we Sem Un Mm oe 50 B SELECTING OTHER UTILITY STITCH PATTERNS _ 22 C MIRROR REVERSE STITCH 222 HELPFUL HINTS een 51 D ELONGATION 23 Messages on LCD 52 E SETTING STITCH WIDTH AND LENGTH 23 MODEL 9960 xmmm PREFACE Thank you for your purchase of this sewing machine This machine intended for household use will provide you with excellent performance in sewing from light to heavy material Please refer to this booklet for proper use and optimum service To get the most out of your sewing machine read the entire instruction manual before attempting to operate the machine Then familiarize yourself with the machine by following the instruction manual page by page To ensure that you are always provided with the most modern sewing capabilities the manufacturer reserves the right to change the appearance design or accessories of this sewing machine when considered necessary without notification or obligation Copyright 2010 THE SINGER COMPANY All Rights Reserved Throughout The World FOR EUROPEAN AND SIMILAR TERRITORIES m This product is suppressed for radio and television interference with the International Electrotechnical Commission req
6. 14 4 4 14 4 e e 2 3 m ET FGH PQRST a A A A 14 lt 7 14 lt gt rl iR t X POR ST a A A EDIT C EDT ee 14 4 14 4 e e 1 5 c By pressing the far left cursor I button the first selected pattern will be highlighted d By pressing the far right cursor I gt button the cursor is moved to the right side of selected patterns The cursor is used to check selected patterns insert patterns delete patterns or editing of each pattern as described below If the settings of the highlighted pattern can be changed it will be noted in the center line of the LCD C TO CHECK SELECTED PATTERNS As the length of the string increases patterns will disappear from sight You can check patterns by shifting cursor to the left D INSERTING PATTERN 1 Machine will insert a pattern to the left of the highlighted letter or pattern 2 Using the cursor buttons move the cursor to highlight the pattern just before the desired position for the new pattern Select the pattern E TO DELETE PATTERN 1 Shift the cursor to the pattern you want to delete 2 Press the clear button quickly less than 0 5 sec Machine w
7. 7 To prevent accidents Be sure the needle does not hit the dress pin while sewing 26 ELASTIC STITCH SEWING Elastic stitches are strong and flexible and will give with the fabric without breaking Good for easy to ravel and knit fabrics as well as joining durable fabrics such as denims No 6 Straight Stretch Stitch No 7 Stem Stitch for Stretch fabrics No 17 Ric rac Stitch General Purpose Foot A We recommend that you use a needle for knit and synthetic fabrics to prevent skipping stitches and thread breakages a Jacket b Trousers c Bag d Pocket QUILTING A quilt always consists of three layers of material The top middle and bottom The top layer is formed by multiple geometrically shaped pieces of materials joined together No 1 Straight stitch Center Needle Position No 8 Hand look Quilting Stitch Straight Stitch Patch Quilting Foot Quilting Bar A CAUTION To prevent accidents Do not change the needle position Otherwise needle could hit the presser foot and break A Joining the pieces of fabric Join the pieces of fabric using Pattern No 1 witha seam allowance of 1 4 inch 6 3 mm B Quilting Sew three layers of material Use quilting bar to sew successive rows Insert qui
8. Oo 1 2 104105 zzz zs LLLLLLLELLLLUZN sg KR 155 _ www _ gt 7 Machine will sew the buttonhole in the order as shown and stop automatically after sewing 8 Press the thread cutter button and raise the presser foot to remove the fabric b To sew over same buttonhole raise presser foot to return to original position 9 Cut center of buttonhole being careful not to cut stitches on either side Use a pin as a stopper To prevent accidents When using seam ripper do not put your finger in the path of ripper A Note For sewing buttonholes on hard to sew fabrics or along the edge of multi layered garments install the underplate to create perfect buttonholes Place the fabric between the underplate and buttonhole foot UN 35 BOUND BUTTONHOLE A bound buttonhole provides a professional tailored touch to women s dresses suits and coats 116 Bound Buttonhole Buttonhole Foot F 1 Cut a patch of fabric 2 5 cm wide 1 cm longer than the finished buttonhole Baste a patch so that the center line of patch will align with the center line mark of buttonhole a Righ
9. PEL ABCDEFGHIJKLMNOPQRSTUVWXYZAAAZECEEGIO SU abcdefghijklmnopqrstuvwxyz aeg gi g su0123456 789 7 7 P amp I 7X9 Gat ES 0123456789 7 amp 1 ADJUSTING THE FORWARD AND REVERSE STITCHES Depending on the type of fabric you sew it may be necessary to adjust the forward and reverse stitches The adjustment is needed when the decorative or letter stitch is distorted Turn screw which is located bottom of the machine in either direction as may be required DECORATIVE STITCH PATTERN 1 If patterns are distorted as illustration a turn Screw in direction of symbol 2 If patterns are distorted as illustration b turn screw in direction of symbol LETTER STITCH PATTERN 1 If patterns are distorted as illustration c turn Screw in direction of symbol 2 If patterns are distorted as illustration d turn screw in direction of symbol b 49 MAINTENANCE T To reduce the risk of electric shock Disconnect the power line plug from electric outlet before carrying out any maintenance CLEANING If lint and bits of thread accumulate in the hook this will interfere with the smooth operation of the machi
10. ii 42 TWIN NEEDLE SEWING m Interesting decorative stitches can be produced by using twin needles and threading the machine with two different colors of thread Always make test samples to help you determine the settings best suited to a specific purpose All patterns except No 101 116 may be sewn with a twin needle General Purpose Foot or Satin Foot A B Note A twin needle is not provided with this machine Call for your Singer Dealer to purchase To prevent accidents a Use only needle designed for this machine Singer Style 2025 Other needles may break b The needle threader cannot be used Thread each needle eye by hand 1 Remove the single needle and insert twin needle Thread the first thread as usual following threading route 3 Thread the left needle eye by hand from front to back Push the Auxiliary Spool Pin with felt washer into the hole 5 Place second spool of thread and thread second thread the same as first 6 For better sewing results do not place the thread into the needle bar thread guide Thread right needle eye by hand from front to back 7 Press the twin needle button LCD will indicate twin needle mark and the stitch width will be reduced automatically 78
11. INSTRUCTION MANUAL SINGER INSTRUCTION MANUAL This sewing machine is intended for household use This sewing machine is not intended for use by young children or infirm persons without supervision IMPORTANT SAFETY INSTRUCTIONS When using a sewing machine basic safety precautions should always be followed including the following Read all instructions before using ADANGE R To reduce the risk of electric shock Never leave unattended when plugged in Always unplug this machine from the electric outlet immediately after using and before cleaning AWARN To reduce the risk of burns fire electric shock or injury to persons 1 Do not allow to be used as a toy Close attention is necessary when this sewing machine is used by or near children 2 Use this sewing machine only for its intended use as described in this manual Use only attachments recommended by the manufacturer as contained in this manual 3 Never operate this sewing machine if it has a damaged cord or plug if it is not working properly if it has been dropped or damaged or dropped into water Return the sewing machine to the nearest authorized dealer or service center for examination repair electrical or mechanical adjustment 4 Never operate the sewing machine with any air openings blocked Keep ventilation openings of the sewing machine and foot controller free from the accumulation
12. 10 BLIND HEM STITCHING C NEEDLE UP DOWN SLOW BUTTON 10 PATCH WORK D SPEED CONTROL BUTTON 10 Di SREED CONTROL BUTTON APPLIQUE An rn en een F THREAD CUTTER BUTTON 11 INSERTING ZIPPERS bi DROP FEED LEVER 11 CENTERED INSERTION 32 TOP COVER NEL J HAND WHEEL 11 To stitch around the zipper tab Diagram 33 EXTRA WIDE TABLE 13 BUTTONHOLE SEWING 34 12 BOUND BUTTONHOLE 36 tad EVEL ET dead ec atis editi tm D 37 12 AUTOMATIC BAR TACK AND DARNING 38 CONTROL PANEL A L C D DISPLAY u B L C D CONTRAST CONTROL C PATTERN 12 D DIRECT STITCH SELECTION BUTTONS 42 SEWING ON BUTTONS 39 E UTILITY STITCH 12 Thread Shank ne 99 F DECORATIVE amp LETTER STITCH BUTTON 12 NARROW HEMMING 40 G FUNCTION BUTTONS 12 CORDING 40 EDIT BUTTON 12 SINGLE CORDING 40 N a TRIPLE CORDING 40 E CUBR BUTTONS Zia CONTINUOUS DECORATIVE PATTERN 41 E FAOK BUTTON S 13 SEWING THIN FABRICS nassen _ 41 M TWIN NEEDLE BUTTON 13 USING THE EVEN FEED FOOT TO TURN OFF THE AUDIBLE BEEP BOBBIN SETTING 18 A ATTACHING THE EVEN FEED FOOT 14
13. H EDIT BUTTON When selecting decorative amp letter stitch you can change the setting of each pattern by pressing this button I 1 1 1 1 ooo E u 1 gt und A Jix2 Eid RIEF TONER 9 1 1 62 63 ESS at SE N HIRE 6 EUM 5 x5 x5 x5 x5 x5 5 x5 5 Ad ABCDEFGHIJKLMNOPQRSTUV A Alabcdefghijklmnopqrstuvwxyzaa C3 e d gt Bm z i C ooo i EDT C i i i 14 4 i i m i 3 I CLEAR BUTTON UTILITY STITCH SEWING If you changed the setting mirror reverse 1 B elongation stitch width length and thread tension of utility stitch pattern you can return to preset setting by pressing this button DECORATIVE amp LETTER STITCH SEWING d Hm By pressing this button you can delete one combined stitch pattern or all stitch patterns J SCROLL BUTTONS During stitch pattern selection 5 patterns or letters will scroll up or down by pressing these buttons K CURSOR BUTTONS EDIT A
14. 06 Straight stretch stitch Reinforcement straight stitch i Al Ah 4h x2 2X2 07 Stem stitch for stretch fabrics 21 22 23 24 25 26 27 28 29 30 08 Quilt stitch like hand made 2 09 Zigzag stitch For overcasting applique patch work etc zx 10 Elastic blind hem a 11 Blind Hem 2 2 2 2 2 2 12 Multiple stitch zigzag For overcasting knit fabrics elastic Faxe xexe X 3 x sewing 13 Button sewing 14 Decorative stitch 15 Overcasting 16 Overcasting of stretch fabric decorative stitch 17 Ric Rac stitch 18 Double Ric Rac stitch 19 Fagoting 20 Patch work A 21 100 Decorative and Functional stitches 51 52 53 54 55 56 57 58 59 60 101 Eyelet 102 Bar tack 103 Darning 104 Bar tack Buttonhole Narrow 2 2 2 2 2 105 Bar tack Buttonhole Wide SEE 106 Keyhole Buttonhole 107 Keyhole Buttonhole with cross bar 108 Tapered Keyhole Buttonhole 109 Round Ended Buttonhole Narrow 110 Round Ended Buttonhole Wide 111 Round Ended Buttonhole with cross bar 112 Both Round Ended Buttonhole 113 Decorative Buttonhole 114 Stretch Buttonhole 115 Heirloom Buttonhole 116 Bound Buttonhole od QQQ RR IP 1 25 I Ke Ces WI Alk aja e m me N N N Al m N o N M my oo TRL Rx Wy oe ORO BIS RR NI
15. This mark is meaning that sewing is interrupted You can continue sewing by starting the machine again b When you stopped sewing at the middle of selected patterns and If you have raised the presser foot lifter the arrow mark will change to P In this time when you start sewing again machine will sew from the beginning of interrupted pattern c If you want to sew from the beginning of all patterns shift the cursor by using the cursor buttons Arrow icon will disappear 48 24 25 21 22 2 a 4 LT Ao ism idea imm E 21 z2 23 24 25 PA DA DECORATIVE AND LETTER EG STITCH CHART 38 The decorative patterns in bold print are one unit C i 5 5 5 5 of the stitch pattern Description of Chart Symbols ik Mirror Stitch included in Reverse Stitch included ou 5 WEST G 4 Mirror and Reverse stitch included 21 22 23 24 25 26 27 28 29 30 31 32 33 34 ne Lo eee hehe dA ABCDEFGHIJKLMNOPQRSTUVWXYZAAAAECEEGIO SU abcdefghijklmnopqrstuvwxyz aeg gi gsu0 123456789 2 amp ABELEF Sq C LOAD YS bch AECEEGIOUSU abedefghijklmnopgrsturwxyza geegr og 0723456 789
16. When the foot controller is connected start stop button will be deactivated See page 10 1 Turn off the power switch symbol O 2 Push foot controller plug into the jack on machine Place foot controller at your feet Turn on the power switch Alamp will light up when switch is turned on The harder you press the foot controller the faster the machine will sew The machine will stop when foot controller is released WARNING To reduce the risk of burns fire electric shock or injury to persons 1 Turn off the power when connecting the foot controller to the machine 2 Handle the foot controller with care and avoid dropping it on the floor Be sure not to place anything on top of it 3 Use only foot controller provided with this machine Type 4C 337B x WW LS I NE FUNCTION OF EACH PART A START STOP BUTTON The machine will start running when start stop button is pressed and will stop when pressed the second time The machine will rotate slowly at start of sewing MONITOR LAMP Green Light Ready to sew or bobbin winding Red Light Presser foot is not in down position or buttonhole lever is not lowered If the red light is on the machine will not start even when start stop b
17. Experiment with fabric scraps until you get the desired length and width A SEWING THIN FABRICS When sewing thin fabrics it is suggested that you use stabilizer on the backside of the fabric USING THE EVEN FEED FOOT The Even feed foot accessory equalizes the feeding of the upper and lower layers of fabric and improves the matching of plaids stripes and patterns This foot helps to prevent uneven feeding of very difficult fabrics No 1 2 or 9 Even feed foot A ATTACHING THE EVEN FEED FOOT 1 Remove the presser foot and holder See page 7 2 The arm of even feed foot should ride onto the shaft of the needle clamp screw 3 Slide the attaching head from your left to right so that it is fitted into the presser bar 4 Tighten the presser foot thumb screw B SEWING Hold both thread lightly at start of sewing and sew in slow 1 2 speed lit u 1 1 m 1 a tat ng t t aa 1 1 n TETTE ME wow ar yat nar 1 Dn fi D J ININININININININ DARNING FREE HAND EMBROIDERY No 1 Center needle Position Darning Embroidery Foot A ATTACHING THE DARNING EMBROIDERY FOOT 1 Lower the feed dogs by moving the drop feed lever to the left 2 Remove the presser
18. B SEWING Les 3 DARNING FREE HAND EMBROIDERY 42 A REMOVING THE 14 SETTING SPOOL OF THREAD ON GPOOE PIN 7 44 ATTACHING THE DARING EMBROIDERY FOOT 42 C WINDING THE BOBBIN 14 42 D INSERTING THE BOBBIN 15 FREE HAND EMBROIDERY 42 4 6 After darning or free hand embroi THREADING THE MACHINE TWIN NEEDLE SEWING A PREPARING TO THREAD MACHINE NE ee EEE eres B SETTING SPOOL OF THREAD ON SPOOL PIN 16 DECORATIVE amp LETTER STITCH SEWING 44 C THREADING THE UPPER THREAD 16 SELECTING DECORATIVE amp LETTER STITCH selecting D THREADING THE NEEDLE EYE 17 mode E DRAWING UP THE BOBBIN THREAD 17 SHIFTING THE CURSOR m STARTING TO SEW 18 TO CHECK SELECTED PATTERNS 45 AC START AND END OF SEAM 4g INSERTING PATTERN 45 B REVERSE STITCHING g E TO DELETE PATTERN 20 40 CORDTOTACKSTTCH 4g EDITING OF EACH PATTERN 46 D TURNING CORNERS 20 G TO RECALL THE SELECTED PATTERNS 47 E SEWING HEAVY FABRIC Bi 30 SEWING THE SELECTED PATTERNS 2 48 E SEWING OVER OVERLAPPED AREAS A 30 SEW PATTERN FROM BEGINNING 48 WIDTH OF SEAM ALLOWANCE 20 DECORATIVE AND LETTER STITCH CHART 49 THREAD TENSION
19. No 9 12 General Purpose Foot A Place fabric so that needle will fall nearest to edge of fabric when using the General Purpose Foot e For narrower zigzag width Width 2 0 4 5 f Use No 12 when sewing easy to ravel or stretch fabrics C NOTE You can also cut off the excess material after sewing the inside of fabric Be careful not to cut thread when cutting excess fabric VK N IN N BN LENG AON NAN BLIND HEM STITCHING This stitch will sew without stitches showing on right side of fabric No 10 Blind hemming for stretch fabric No 11 Blind hem for regular fabric Blind Hem Foot D 1 Fold the fabric as shown on drawing a Medium Heavy weight fabric b Light weight fabric c Wrong side of fabric d Overcasting 2 The guide e on the blind foot ensures even feeding of the fabric when blind hem stitching The guide e is adjusted by turning the adjusting screw f 3 Place fabric so that the straight stitches or small zigzag stitches are on the protruding hem edge and the large zigzag stitches just catch one thread of the folded edge g Turn the screw so that the needle barely touches the folded edge of fabric 4 Lower the presser foot and sew hem guiding fabric evenly along the guide 5 Turn the fabric over when you have completed sewing c Wrong side of fabric h Right side of fabric 3
20. STITCH PATTERN Utility stitches are indicated in the pattern chart located inside of the top cover When you turn on the machine straight stitch will be selected automatically Select utility stitch pattern as follows A DIRECT STITCH PATTERN You can select basic utility stitch patterns directly by pressing the Direct Stitch Selection Buttons Selected pattern will be indicated on the LCD B SELECTING OTHER UTILITY STITCH PATTERNS 1 Press the utility button First 5 patterns will be indicated on the LCD 2 Press the right scroll button next 5 patterns will appear By pressing the left or right scroll button you can scroll up or down in increments of 5 patterns You can also scroll down by pressing the utility button 3 To select a pattern press the function button directly under the desired pattern 4 When pattern is selected LCD will indicate the information of selected pattern Stitch information mode a Stitch Number and pattern b Suitable presser foot c Function of function button F2 Mirror reverse F3 Elongation F4 Stitch Width Length F5 Thread Tension See previous page If the function mark is not indicated its funtion can not be used C MIRROR REVERSE STITCH You can set the mirror stitch or reverse stitch or mirror reverse stitch Pressing the function button F2 directly under the mirror reverse icon stitch will flip from left to right or from front to back The icon on the LCD indicates the
21. Stitching Used for easy to ravel and knit fabrics Needle should fall on extreme edge of fabric Refer to next page for overcasting FREE ARM SEWING By simply removing the extension table machine becomes a free arm machine making hard to reach areas readily accessible Note Refer to page 7 for Removing The Extension Table 28 AAAA NEE NSE NIN TE NSD ON M NNNM M vi OVERCASTING OVERLOCKING A USING THE OVERCASTING FOOT No 9 Stitch Width 5 0 No 15 16 30 Stitch Width 5 0 7 0 Overcasting Foot C Press fabric against the guide plate of the overcasting foot so that needle falls near the edge of seam a No 9 Width 5 0 is used for preventing raveling of fabrics b d No 15 16 30 can sew overcasting and regular stitches at the same time Therefore it is convenient for sewing easy to ravel and stretch fabrics Dan To prevent accidents Overcasting foot should be used for sewing patterns 9 15 16 30 only Do not change the stitch mode or elongation It is possible that the needle could hit the presser foot and break when sewing other patterns and widths B USING THE GENERAL PURPOSE FOOT
22. controller is connected 12 Release the needle up down slow button 13 Release the thread cutter button 14 Turn off the power switch o 52 53 54 55 9960English 34108 BO
23. ee When decorative amp letter stitch sewing you can 1 YH g check and edit combined patterns or letters by eed ee pressing these buttons i 14 gt l L TACK BUTTON Sg t 3 7 UTILITY STITCH SEWING E gt e By pressing this button you can sew a tack stitch AN P at the beginning and at the end of a stitch SEE L M PAGE 19 DECORATIVE amp LETTER STITCH SEWING If this button is pressed at the end of a decorative stitch pattern machine will stop automatically at the end of the stitch pattern and tie off the stitch with a locking stitch M TWIN NEEDLE BUTTON If you attach the twin needle press this button Machine will reduce the stitch width SEE PAGE 43 TO TURN OFF THE O on or AUDIBLE BEEP E You can operate the machine without the audible t beep 1 Turn off the power switch am 2 Turn on the power switch while pressing the e EDIT button and the function F1 button A 3 This function is kept off until the machine is ON OFF F1 turned off m 4 ch Ed This function turns off the single beep only Multiple beeps will not turn off BOBBIN SETTING A REMOVING THE BOBBIN 1 Pull the bobbin cover latch to the right and remove the bobbin cover 2 Lift up the bobbin from the machine B SETTING SPOOL OF THREAD ON SPOOL PIN 1 Pull up the left end of spool pin and set the spool of th
24. foot and holder See page 7 3 The arm of darning embroidery foot should ride onto the shaft of the needle clamp screw 4 Slide the plastic attaching head from your left to right so that it is fitted into the presser bar 5 Tighten the presser foot thumb screw DARNING Place fabric under foot and lower Grasp fabric firmly in front and back of area to be darned Operate machine moving fabric by hand forward and backward with an even motion stitching in closely spaced rows over the hole or worn area 3 When the area is filled with new stitches move fabric from side to side in a similar manner to weave or reinforce the stitching a Note Reinforce open areas with an underlay baste underlay in place before darning NU C FREE HAND EMBROIDERY Outline the design for embroidery on the surface of the fabric 2 Place design to be embroidered between the two sections of embroidery hoop Note Embroidery hoop is not included with this machine 3 Set embroidery hoop under needle and lower the foot 4 Start the machine at medium speed guiding hoop carefully so needle moves along line of the pattern D After darning or free hand embroidery Raise the feed degs by moving the drop feed lever to the right ummy
25. for sewing center needle position straight stitch No 1 only It is possible that needle could hit the presser foot and break when sewing other patterns 1 Baste the zipper opening to the seam line a Straight stitch b End of opening c Basting d Wrong Side of fabric 2 Press open the seam allowance Baste the zipper tape Place the open zipper face down on the seam allowance with the teeth against the seam line 3 Attach the zipper foot Attach the left side of the presser foot pin to the presser foot holder when sewing the right side of the zipper and right side of the presser foot pin to the holder when sewing the left side of the zipper 4 Stitch left side of the zipper from bottom to top 5 Stitch across the lower end and right side of zipper Remove the basting and press 32 INSERTING ZIPPERS LAPPED INSERTION No 1 Straight Stitch Center Needle Position Zipper Foot E 7 ae To prevent accidents Zipper foot should be used for sewing center needle position straight stitch No 1 only It is possible that needle could hit the presser foot and break when sewing other patterns 1 Baste the zipper opening to the seam line a Straight stitch b End of opening c Basting d Wrong Side of fabric N Fold back to the left s
26. function button directly under the indicated pattern Selected pattern will be indicated on the top left side of LCD 5 Using this same procedure select the next patterns Patterns will appear at the top of the LCD in the order selected 6 As selected patterns over the indicating area disappear from the screen you can check them by pressing the cursor buttons See next page NOTE Machine can memorize a maximum of 60 patterns You can combine the tack stitch by pressing the tack button This is used for sewing a single combination of patterns See next page 48 B SHIFTING THE CURSOR Additional patterns may be added to the end of a string of combined patterns Shift the I cursor over to the right following the pattern string and then select new patterns By pressing the cursor buttons cursor will shift left or right The cursor position will be highlighted a Press the cursor left button lt and cursor will shift to the left b By pressing the cursor right gt button cursor will shift right 44 em 16 17 18 16 17 18 19 20 illl ate EA c gh llli S2 S E a A A A Ah A EDIT C EDIT
27. of lint dust and loose cloth 5 Never drop or insert any object into any opening 6 Do not use outdoors 7 Do not operate where aerosol spray products are being used or where oxygen is being administered 8 To disconnect turn the power switch to the off position symbol O then remove plug from outlet 9 Do not unplug by pulling on cord To unplug grasp the plug not the cord 10 Keep fingers away from all moving parts Special care is required around the sewing machine needle 11 Always use the proper needle plate The wrong plate can cause the needle to break 12 Do not use bent needles 13 Do not pull or push fabric while stitching It may deflect the needle causing it to break 14 Switch the sewing machine off symbol O when making any adjustments in the needle area such as threading needle changing needle threading bobbin or changing presser foot 15 Always unplug sewing machine from the electrical outlet when removing covers lubricating or when making any other user servicing adjustments mentioned in the instruction manual 16 Handle the foot controller with care and avoid dropping it on the floor Be sure not to place anything on top of it 17 Use only the handle to lift and move the machine 18 Do not expose the machine or machine case to sunlight directly Also do not keep it in a very warm or damp place SAVE THESE INSTRUCTIONS Servicing should be performed by an authorized service rep
28. seam press the reverse button Machine will sew a few stitches backward and Sew a few stitches forward and stop automatically 4 Press the thread cutter button p g Lei a ee o 25 BASTING You can baste a garment before trying it on No 5 Basting Stitch Darning Embroidery Foot A ATTACHING THE DARNING EMBROIDERY FOOT 1 Lower the feed dogs by moving the drop feed lever to the left 2 Remove the presser foot and holder See page 7 3 The arm of darning embroidery foot should ride onto the shaft of the needle clamp screw 4 Slide the plastic attaching head from your left to right so that it is fitted into the presser bar 5 Tighten the presser foot thumb screw B BASTING When this pattern is selected thread tension will be reduced automatically 1 Place the fabric under the presser foot and lower it 2 Hold the upper thread and bobbin thread loosely and start to sew Machine will make one stitch only 3 Pull the fabric required amount to the rear and sew one stitch 4 Repeat this as many times as you need to finish the seam 5 Raise the fabric feed dogs for next regular sewing Note To prevent the fabric layers from shifting insert dress pins crosswise to the basting position
29. small opening between cap and spool as illustration C THREADING THE UPPER THREAD Hold thread in both hands and pass thread to the guide from front opening 2 Bring thread backward and pass through the slit from right to left 3 Bring thread to the left and pull thread down toward you along the slit 4 Pull up thread 5 To thread the take up lever draw thread up and bring thread back down again from right to left along the slit 6 Pull thread downward along the slit 7 Draw thread through thread guide from right side opening 8 Pass through needle eye from front to back Refer to next page for instructions on how to use needle threader D THREADING THE NEEDLE EYE d cundis To prevent accidents 1 Keep fingers away from all moving parts Special care is required around the needle 2 Do not lower the threader lever while machine is operating Note The needle threader is used for needle sizes 11 80 14 90 and 16 100 1 Lower the presser foot 2 Check that the needle is raised If itis not so raise needle
30. with Felt Washer Screw Driver Driver for Needle Plate Thread Cap On the machine when delivered Small Thread Cap 10 Seam Guide and Screw 11 Overcasting Foot C 12 Blind Hem Foot D 13 Zipper Foot E 14 Rolled Hem Foot 15 Button Sewing Foot 16 Satin Foot B 17 Quilting Bar 18 Open Toe Foot 19 Cording Foot 20 Straight Stitch Patch Quilting Foot 21 Darning Embroidery Foot 22 Even feed Foot 23 Buttonhole Foot F and Under Plate 24 General Purpose Foot On machine when delivered A An Extra Wide Table is provided with this machine See Page 11 OPTIONAL ACCESSORIES 25 Single Welt Cord Foot 26 Adjustable Bias Binder 27 Braiding Foot 28 Stitch in the Ditch Foot 29 Clearance Plate 30 Braiding Guide 31 Fancy Trim Foot 32 Shank w o metal DUST COVER Cover the machine with dust cover when it is not to be used a The manual may be stored in the compartment of the dust cover by opening the front cover towards you Do not remove the styrofoam located inside of this cover EXTENSION TABLE a REMOVING THE EXTENSION TABLE Hook your finger to the left bottom side of extension table and slide it to the left To attach insert to the right b OPENING THE ACCESSORY CASE Hook your finger to the left side of accessory case and pull toward you CHANGING THE PRESSER FOOT The presser foot must be changed a
31. 0 As ere IA a 3 5mm oMN 4 PATCH WORK For additional decorative purposes use different kind of materials No 19 20 General Purpose or Satin Foot A B 1 Place two pieces of fabric right sides together and sew a long straight stitch 2 Press the seam open 3 Be sure that stitches fall on both sides of fabric APPLIQUE No 23 24 Open Toe Foot A CAUTION To prevent accidents Do not change the stitch width to wider than 5 0 Otherwise needle could hit the presser foot and break 1 Fix applique on fabric with fabric glue fusible iron on or basting stitches 2 Sew edge of applique while dropping the needle as close to the edge as possible The straight stitch is almost entirely sink stitched and a hand made effect is obtained a When sewing sharp angles Bring needle to lowest position and raise the presser foot Use needle as pivot and turn fabric lit 31 INSERTING ZIPPERS CENTERED INSERTION No 1 Straight Stitch Center Needle Position Zipper Foot E To prevent accidents Zipper foot should be used
32. Wrong side of fabric NOTE When sewing weaker fabric reinforce buttonhole area Cut a patch of fusible interfacing 3 cm wider and 2 cm longer than the buttonhole Fuse to wrong side over each buttonhole marking EYELET This stitch pattern is used for making belt holes and other similar applications 101 Eyelet Satin Foot B You can choose 3 sizes of eyelets by changing the stitch length 1 Place the fabric under the presser foot and lower the presser foot Start the machine Machine will sew the eyelet and stop automatically 2 Press the thread cutter button and raise the presser foot 3 Make a hole in the center of the eyelet Note Eyelet punch is not provided with this machine 101 AUTOMATIC BAR TACK 102 103 AND DARNING You can sew automatic bar tack and darning using the buttonhole foot No 102 Bar tack to reinforce areas that will be subject to strain such as pocket corners No 103 Darning mending and other applications Buttonhole Foot F 1 Adjust slide on base according to the length of bar tack or darning Length of bar tack or darning 2 Pass upper thread through the hole of buttonhole foot and bring
33. ar C button thread tension will return to pre set By pressing the function F1 button LCD return to the previous mode Stitch information mode When another stitch pattern is selected thread tension will return to pre set You can start sewing at this mode and change tension while sewing A Preset thread tension Upper and bobbin thread will lock appromaximately in the middle of fabric B When thread tension is increased Bobbin thread will appear on the top side of fabric C When thread tension is decreased Upper thread will appear on the bottom side of fabric D Thread tension except for straight stitch Thread tension except for straight stitch is set to a slightly weaker tension than when sewing straight stitch You will obtain a nicer stitch when upper thread appears on bottom side of fabric E Helpful Hints 1 If your sewing appears as shown on drawing stitches on top side of fabric are good but bottom side tends to look like a towel it could be that the upper thread is not threaded correctly Refer to page 16 for correct threading 2 If after checking the top thread and the bobbin thread is still showing on the top side check the bobbin to see if it is set correctly Refer to page 15 for the correct setting 21 SELECTING UTILITY
34. better sewing results 8 CONNECTING THE MACHINE A DANGER To reduce the risk of electric shock Never leave unattended when plugged in Always unplug this machine from the electric outlet immediately after using and before maintenance WARNING To reduce the risk of burns fire electric shock or injury to persons Do not unplug by pulling on cord To unplug grasp the plug not the cord 1 Place machine on stable table 2 Connect the power line cord to the machine by inserting the 2 hole plug into the terminal box Turn on the power switch Alamp will light up when switch is turned on To disconnect turn the power switch to the off position symbol O then remove plug from outlet FOR UNITED STATES AND CANADA USERS POLARIZED PLUG INFORMATION Connect power line plug to the electric outlet This appliance has a polarized plug one blade wider than the other To reduce the risk of electric shock this plug is intended to fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not modify the plug in any way FOOT CONTROLLER Use of foot controller will permit control of start stop and speed with your foot
35. ble Accessories 11 Presser Foot Lifter 12 Forward Reverse Adjusting Screw underneath machine 13 Foot Controller 14 Power Line Cord 15 Hand Wheel 16 Power Switch 17 Terminal Box 18 Controller Jack 19 Direct Stitch Selection Buttons 20 EDIT Button 21 Tack Button 22 Twin Needle Button 23 Utility Stitch Button 24 Decorative Stitch amp Letter Button 25 Liquid Crystal Display L C D 26 Function Buttons F1 F5 27 Clear Button 28 Scroll Buttons 29 Cursor Buttons 30 Thread Cutter 31 Buttonhole Lever 32 Needle Threader Lever 33 Needle Threader 34 Presser Foot Thumb Screw 35 Presser Foot Holder 36 Presser Foot 37 Fabric Feed Dogs 38 Needle Clamp Screw 39 Needle Thread Guide 40 Needle 41 Bobbin Cover Latch 42 Bobbin Cover 43 Needle Plate 44 Drop Feed Lever 45 Pattern Chart 46 Thread Guide 47 Thread Guide 48 Bobbin Winder Thread Guide 49 Thread Tension Regulator 50 Spool Stand 51 Felt Washer 52 L C D Contrast Control 53 Auxiliary Spool Holder 54 Bobbin Winder Shaft 55 Bobbin Winder Stop OONOT WN 25 26 27 29 51 52 535455 5 ACCESSORIES Accessories are provided in the accessory case See next page EXTENSION TABLE Needle Pack 4 Bobbins 1 is in the machine Seam Ripper Brush Auxiliary Spool Pin
36. by pressing needle up down button 3 Lower the threader slowly and draw thread through thread guide a and pull toward the right 4 Lower the lever as far as it will go The threader will turn and the hook pin will go through the needle eye 5 Draw thread into the guide 6 Hold thread loosely and release the lever Hook will turn and pass thread through needle eye while making a loop 7 Pull thread out about 10 cm 4 inches from needle eye E DRAWING UP THE BOBBIN THREAD 1 Raise the presser foot 2 Hold thread loosely and press needle up down button twice from up position The hand wheel will turn one complete turn 3 Pull upper thread lightly Bobbin thread will come up in a loop 4 Pull both upper and bobbin threads about 10 cm 4 inches toward the back of presser foot 17 STARTING SEW The machine will be set to sew straight stitch when power switch is turned on A CAUTION To prevent accidents While sewing special care is required around the needle Machine automatically feeds the fabric do not pull or push the fabric A START AND END OF SEAM 1 Check the presser foot General Purpose Presser Foot Refer to page 7 for changing the presser foot 2 Place the fabric under the presser foot and lower the presser foot 3 Hold back both threads and press the start stop button or press the f
37. ccording to the stitch you sew or work you do CAUTION To prevent accidents Turn off the power switch before you change the presser foot A Changing the presser foot 1 Turn the hand wheel toward you until the needle is at its highest point 2 Raise the presser foot lifter 3 Remove the presser foot by pushing the presser foot release lever toward you 4 Place desired foot with its pin directly under the slot in presser foot holder 5 Lower the presser foot lifting lever and the presser foot will snap into place B Removing the presser foot holder When attaching the special presser foot or cleaning the machine you should remove the presser foot holder 1 Remove the presser foot 2 Loosen the presser foot thumb screw and remove the presser foot holder 3 To replace the holder pull up the holder as far as it will go from bottom of presser bar 4 Tighten the thumb screw oo000000 INSERTING THE NEEDLE Select a needle of the right type and size for the fabric to be sewn 7 10000000 CAUTION To prevent accidents Turn off the power before removing the needle A 1 Turn the hand wheel toward you until the needle is at its highe
38. d tension a Mirror Reverse stitch Press the function button F2 directly under mirror reverse icon stitch will change alternately or in rotation The descriptions of the mirror reverse icons are below a1 Regular stitch normal stitch a2 Mirror stitch flips from left to right a3 Reverse stitch reverse front and back a4 Mirror and Reverse stitch pattern will flip from left to right and from front to back If symbol is not indicated its pattern cannot change mirror reverse stitch b Elongation By pressing the function button F3 directly under the elongation mark stitch will elongate five different sizes b1 b5 If symbol is not indicated its pattern cannot elongate 46 c Setting the stitch width and length Machine will pre set the stitch width and length suitable for the pattern 1 You can make changes by pressing the function button F4 directly under the witdh and length mark 2 For narrower width press function button F2 For wider width press function button For shorter length press function button F4 For longer length press function button F5 Pre set stitch width and length will be indicated as a highlighted number You can change the width and length o
39. ea 50 Fabric pulled while sewing Do not pull fabric 18 Needle is hitting the presser foot Select correct foot and pattern 25 Needle breaks Needle inserted incorrectly Re insert needle 8 Incorrect size needle or thread for fabric Choose correct size needle and 8 being sewn thread Machine runs Dirt or lint accumulated in the hook race and Remove the needle plate and 50 with difficulty feed dog bobbin holder and clean the hook race and feed dog Cord not plugged into electrical outlet Insert plug fully into outlet 9 Power switch is not turned on Turn on the switch 9 Machine will not Bobbin winder spindle is pushed to the right Push spindle to the left 14 run Presser foot is not lowered Lower the foot 10 Buttonhole Sewing Mode Buttonhole lever is not lowered completely Lower the buttonhole lever 34 Buttonhole foot is not attached Attach the buttonhole foot 34 51 Messages on LCD 1 Winding the bobbin EE amp 2 Lower the buttonhole lever 3 After sewing buttonhole raise the presser foot lifter and set the frame of buttonhole foot to starting position n h T cow Hf 4 Release the foot controller pedal Ee 5 Lower the presser foot 6 Machine cannot memory any more 7 Select a pattern 2 8 8 Release the reverse button 5 9 Release the start stop button gt 12 10 Rethread the upper thread 11 Foot
40. eam allowance Turn under the right seam allowance to form 3 mm fold 3 Attach the zipper foot Attach the left side of the presser foot pin to the presser foot holder when sewing the right side of the zipper and right side of the presser foot pin to the holder when sewing the left side of the zipper 4 Stitch the left side of zipper from bottom to top 5 Turn the fabric right side out stitch across the lower end and right side of zipper 6 Stop stitching with the needle down in the fabric when the zipper foot reaches the zipper tab about 5 cm from the top of the zipper To stitch around the zipper tab Diagram A 1 Stop stitching before you reach the zipper tab 2 Lower the needle into fabric 3 Raise the presser foot and slide the zipper tab backwards to clear the zipper foot 4 Lower the presser foot and continue stitching 5 Remove the basting stitches a Zipper tab BUTTONHOLE SEWING 104 105 106 107 108 This machine can sew 13 types of buttonholes 104 Bar tack Buttonhole Narrow for light to medium weight fabrics 105 Bar tack Buttonhole Wide for large buttons 106 Keyhole Buttonhole for heavy weight fabrics 107 Keyhole Buttonhole with reinforced bar tack 108 Tapered Keyhole Buttonhole 109 Round Ended Buttonhole Narrow for light to medium weight fab
41. f other patterns by shifting the position of the cursor By pressing the return button F1 machine will return to editing mode By pressing EDIT button machine will return to selecting mode d Setting the thread tension By pressing the function button F5 directly under the tension mark LCD will indicate the tension mode This setting will change the thread tension of all combined patterns To increase the upper thread tension press function button F5 To decrease the upper thread tension press function button F4 Pre set tension number is highlighted By pressing the function F3 AUTO button thread tension will return to pre set By pressing the return button F1 machine will return to editing mode By pressing EDIT button machine will return to selecting mode Note If you press the clear button at editing mode highlighted pattern will be deleted G TO RECALL THE SELECTED PATTERNS If you change the pattern to utility stitch machine will retain the combination of patterns until the machine is turned off To recall these patterns press the decorative amp letter stitch button Machine will recall the selected patterns Thread tension will return to pre set To delete all patterns press and hold the clear C button for a long time See page 45 IL n Eg am 1 fg JL J A A A A A 4 FA F2F3F4F5
42. ill delete the pattern and cursor will shift to next pattern a When the cursor is at furthest right side machine will delete just before pattern 3 If you want to delete all patterns press and hold the clear C button over 0 5 sec Machine will delete all selected patterns 22 TUL IPI ET F EDITING OF EACH PATTERN You can change the stitch width length mirror reverse stitch and elongation of each pattern And you can change the thread tension of selected all patterns 1 Press the EDIT button LCD will change to the editing mode 2 As you shift the cursor the setting of each pattern will be indicated 3 By pressing each function button you can change setting as below a d 4 After you have completed the editing press the return button F1 or EDIT button Machine will return to selecting mode Note Letter stitches cannot change settings except for threa
43. lting bar into the hole of presser foot holder and set the space as you desire C Hand Look Quilting Stitch No 8 Use invisible nylon sewing thread or very lightweight thread that matches the fabric on top Place thread that contrasts to the color of the fabric on the bobbin Set the upper tension to maximum When you sew bobbin thread will pull to the top and give the appearance of a traditional hand quilting stitch 0 mus XX 20 JF 27 ZIGZAG STITCH SEWING Your machine can sew zigzag stitches of various widths and lengths by changing the settings of the stitch width and stitch length No 9 Zigzag Stitch General or Satin Foot A B Zigzag stitches are very good for joining two pieces of fabrics applique and sewing various decorative patterns SATIN STITCHING To sew a satin stitch shorten the stitch length and attach the satin foot B Refer to next page for overcast MULTI STITCH ZIGZAG m Used for sewing on elastic and overcast stitching on knit fabrics No 12 Multi Stitch Zigzag General Purpose Foot A A Elastic Band Sewing Pull elastic in front and back of needle while sewing B Overcast
44. n F2 For wider width press function button For shorter length press function button F4 For longer length press function button F5 Pre set stitch width and length will be indicated as a highlighted number When you pressed clear button machine will return to preset stitch width and length When you press the return button F1 LCD will indicate previous mode Stitch Information mode a For straight stitch patterns No 1 2 3 4 6 8 Stitch width buttons will change the needle position To shift the needle to the left press function button F2 To shift the needle to the right press funtion button F3 Note When further width or length adjustments are not possible machine will emit multiple audible beeps If the width length or number icons are not indicated the pattern cannot be changed Adjustments to the patterns may be made while sewing 23 12345 6 7 8 9 10 WHERE TO USE EACH STITCH UNE Ful sd d I 01 Straight stitch center needle positon For top stitching Lt t i zipper sewing etc oooo h 02 Straight stitch left needle position For top stitching etc 1112131415 1617 18 19 20 04 Straight stitch with auto reverse stitch left needle position 05 Basting 03 Straight stitch with auto reverse stitch center needle position E 4203 lt gt
45. n position where back stitching is to be made and lower the presser foot 2 Press and hold the reverse button Sew 4 5 reverse stitch 3 Release the reverse button and press the start stop button or press the pedal Machine will change to forward sewing 4 When you reach the end of seam press and hold reverse button and sew 4 5 reverse stitches Note The pattern No 3 and No 4 have a built in reverse stitch See page 25 to sew this stitch C AUTO TACK STITCH You may sew tack stitches at the beginning and end of the stitch This function can be used with all utility patterns 1 Press the Tack button Tack mark will appear on the L C D 2 Start to sew Machine will sew tacking stitches automatically and then start to sew the selected pattern 3 When you reach the end of seam press the reverse button once Machine will sew tacking stitches and stop automatically 4 If you want to cancel this function press the tack button again Tack mark will disappear OF 19 D TURNING CORNERS 1 Stop the machine when you reach a corner The machine will stop the needle into the fabric 2 Raise the presser foot 3 Use the needle as a pivot and turn fabric 4 Lower the presser foot and resume sewing E SEWING HEAVY FABRIC When sewing heavy fabrics the toe end of presser foot tends to lift up and sewing cannot be started smoothly In such case set a
46. ne Check regularly and clean the stitching mechanism when need A Bobbin Holder Remove the bobbin cover and bobbin Clean the bobbin holder with a brush B Hook Race and Feed Dog Remove the needle presser foot and holder Remove the bobbin cover and bobbin Remove the screws holding the needle plate 2 Remove the needle plate by lifting up the right side of the plate 3 Lift up the bobbin holder and remove it 4 Clean the hook race feed dogs and bobbin holder with a brush Also clean them using a Soft dry cloth 5 Replace the bobbin holder into the hook race so that the tip a fits to the stopper b as shown 6 Replace the needle plate inserting the hook into the machine Replace the screws and tighten Note AnLED lamp is used to illuminate the stitching area It does not require replacement In the unlikely event it does not light call your dealer for service There is no need to lubricate this machine 50 HELPFUL HINTS PROBLEM CAUSE CORRECTION Page Machine not properly threaded Re thread machine 16 Upper thread Thread entwined around bobbin Remove entwined thread 15 breaks Needle inserted incorrectly Re insert needle 8 Thread tension too tight Readjust thread tension 21 Thread of incorrect size
47. ne sliding to the right 4 Adjust the height of table by turning the four rubber feet um U far ih NN A CONTROL PANEL When you turn on the power machine will select the straight stitch and indicate information of stitch on the L C D A L C D DISPLAY Stitch information is indicated on this display According to the pattern or mode information will be changed B L C D CONTRAST CONTROL The contrast of L C D is adjusted by turning this dial C PATTERN CHART Pattern chart is located inside of the top cover All patterns and letters of this machine are indicated on this chart They are separated Utility stitch and Decorative amp Letter stitch D DIRECT STITCH SELECTION BUTTONS By pressing these buttons you can select basic utility stitch patterns directly E UTILITY STITCH BUTTON By pressing this button you may select a utility stitch pattern FOR SELECTING AND SETTING OF UTILITY STITCHES SEE PAGE 22 F DECORATIVE amp LETTER STITCH BUTTON By pressing this button you can select decorative amp letter stitch patterns These patterns and letters are combined easily by selecting each pattern FOR SELECTING AND SETTING OF DECORATIVE amp LETTER STITCH SEE PAGE 44 G FUNCTION BUTTONS Functions of these buttons are changed by selected stitch pattern and mode
48. oot controller pedal Keep holding threads after sewing a few stitches Lightly guide the fabric while sewing You can regulate the sewing speed by sliding the speed control button Also you can reduce the sewing speed by pressing the slow button 4 When you reach end of seam press the start stop button to stop sewing or release the foot controller pedal 5 Press the thread cutter button 6 Raise the presser foot lifter and remove the fabric Upper Thread Sensor If upper thread is broken or missing machine will stop automatically Rethread the upper thread and resume sewing CAUTION 1 Do not press the thread cutter button when there is no fabric in the machine or no need to cut the threads The thread may tangle resulting in damage 2 Do not use the thread cutter button when cutting thread thicker than 30 nylon thread or other speciality threads In this case use the thread cutter located on the left side of the machine See page 11 NOTE After you cut the threads by using the thread cutter button hold upper thread only at the next starting of seam No need to draw up the bobbin thread B REVERSE STITCHING Reverse stitching is used for reinforcing the ends of the seams 1 Place the fabric i
49. or poor quality Choose correct thread 8 Lower thread Bobbin threaded incorrectly Re thread the bobbin 15 breaks Bobbin wound unevenly or too full Rewind the bobbin 14 Dirt on the bobbin holder Clean the holder 50 Needle inserted incorrectly Re insert needle 8 Machine skips Bent or blunt needle Insert new needle 8 stitches Incorrect size of needle Choose correct size needle for 8 fabric on stretch fabric use stretch needle Machine not properly threaded Re thread machine 16 Fabric puckers Bobbin threaded incorrectly Re thread the bobbin 15 Blunt needle Insert new needle 8 Thread tension too tight Readjust thread tension 21 Machine makes Bobbin threaded incorrectly Re thread the bobbin 15 loose stitches or Machine not properly threaded Re thread machine 16 loops Tension not adjusted properly Readjust thread tension 21 Stitch pattern is Presser foot is not suited for the pattern Attach correct foot 25 distorted Thread tension is not balanced Adjust the thread tension 21 Forward and reverse stitch is not balanced Adjust the forward and reverse 49 Threader does Needle is not raised Raise the needle 10 not thread Needle inserted incorrectly Re insert needle 8 needle eye Bent needle Insert new needle 8 Machine does Feed dogs are lowered Raise the feed dogs 11 not feed properly Stitch length not suitable for fabric Regulate stitch length 23 Lint and dust accumulated around feed dog Clean the feed dog ar
50. read on spool pin so that the thread unrolls from the front of the spool 2 Set the spool cap on spool pin as far as it will go a Reverse spool cap direction according to the size of spool b Use the small spool cap when you use cross wound thread Leave small opening between cap and spool as illustration C WINDING THE BOBBIN 1 Hold thread in both hands and hook thread to the guide from front opening 2 Bring thread towards the rear of the machine and pass through the thread guide from left to right 3 Bring thread to the right and pass thread through the thread guide from rear side Pass thread under tension disc in counter clockwise direction 4 Insert thread through hole in bobbin and place the bobbin on bobbin winder spindle Push bobbin to the right to engage bobbin winder LCD will indicate the bobbin winding mode 5 Hold the end of the thread and start the machine by pressing the start stop button or pressing the foot controller pedal 6 After the bobbin winds a few turns stop the machine by pressing the start stop button or releasing the foot controller pedal Cut the thread near hole 7 Start the machine again 8 The bobbin winding will stop automatically when bobbin is full Release the pedal 9 Push the bobbin and spindle to the left 10 Remove the bobbin from the spindle and cut the thread
51. resentative 2 SINGERS is a registered Trademark of The Singer Company Ltd CONTENTS IMPORTANT SAFETY INSTRUCTIONS WHERE TO USE EACH STITCH MODBDEL 9960 5 iibro nina STRAIGHT STITCH SEWING FOR EUROPEAN AND SIMILAR TERRITORIES MN E CO er en H raig I uto loci attern NO 3 MAIN ne A ATTACHING THE DARING EMBROIDERY FOOT DUST COVER B BASTING ann a de ete Lm ne he EXTENSION TABLE ELASTIC STITCH SEWING a REMOVING THE EXTENSION TABLE b OPENING THE ACCESSORY CASE d Joining the pieces of fabric CHANGING THE PRESSER FOOT Quilting A Changing the presser foot B Removing the presser foot holder INSERTING THE NEEDLE FABRIC THREAD AND NEEDLE TABLE CONNECTING THE MACHINE FOOT CONTROLLER FUNCTION OF EACH PART C Hand Look Quilting Stitch No 8 ZIGZAG STITCH SEWING MULTI STITCH ZIGZAG FREE ARM SEWING OVERCASTING OVERLOCKING A USING THE OVERCASTING FOOT 10 USING THE GENERAL PURPOSE NOONAN INREAD CUTTER 11 LAPPED INSERTION A STARUSTOPBUTTON Beh C NOTE i Ser e een B REVERSE STITCH BUTTON
52. ric in the machine or no need to cut the threads The thread may tangle resulting in damage 2 Do not use this button when cutting thread thicker than 30 nylon thread or other speciality threads In this case use the thread cutter H G DROP FEED LEVER The fabric feed dogs project up through the needle plate directly below the presser foot Their function is to move the fabric being sewn The drop feed lever controls the fabric feed dogs For ordinary sewing move the lever to the right This raises feed dogs to their highest position For most sewing the lever should be in this position For darning or free motion embroidery or whenever fabric is to be moved by hand move the lever to the left to lower the fabric feed dogs H THREAD CUTTER Use this cutter if the thread cutter button is not used 1 Raise the presser foot and bring fabric and threads backward after sewing 2 Hook the threads to the thread cutter from back to front 3 Pull fabric and cut threads 1 TOP COVER To open the top cover lift up the right side of cover J HAND WHEEL By turning the hand wheel the needle will raise or lower You should turn hand wheel toward you EXTRA WIDE TABLE If you need wide sewing space attach the extra wide table as below Set the machine and extra wide table on the stable table 1 Remove the extension table See Page 7 2 Stand up the two legs of extra wide table 3 Insert wide table to the machi
53. rics 110 Round Ended Buttonhole Wide for large buttons 111 Round Ended Buttonhole with cross bar 112 Both Round Ended Buttonhole 113 Decorative Buttonhole 114 Stretch Buttonhole 115 Heirloom Buttonhole 116 Bound Buttonhole See page 36 gt 115 116 D 1 55 C Buttonhole Foot F Note Density of buttonhole legs may be adjusted with stitch length control 1 Mark position and length of buttonhole on fabric 2 Set button on the base If button does not fit on the base adjust slide on base to diameter of button plus thickness of button a Length of button thickness 3 Pass upper thread through the hole of buttonhole foot and bring upper and bobbin threads to the left 4 Position fabric under presser foot so that the center line mark is in the center of the buttonhole foot Lower the foot while pulling the frame of the buttonhole foot towards you Note When sewing stretch fabrics it is suggested that you use interfacing on the backside of the fabric 5 Lower the buttonhole lever completely Note Machine will not start to sew if buttonhole lever is not lowered properly or frame of buttonhole foot is not positioned extremely forward 6 Hold upper thread lightly and start the machine 34
54. s follows 1 Raise the presser foot 2 Push the lock button located on the right side of general purpose foot and lower the foot 3 Start sewing As presser foot hinge is locked fabric will be feeded smoothly a The presser bar lifter can be raised 1step higher for placing heavy materials under the presser foot easily F SEWING OVER OVERLAPPED AREAS Guide the fabric with your hand when sewing over overlapped areas G WIDTH OF SEAM ALLOWANCE Guide lines on the needle plate indicate the distance from the center needle positon To keep the width of seam allowance guide fabric edge aligning this guide line Seam Guide Use the seam guide to guide the fabric Attach the seam guide and screw to the needle plate 20 THREAD TENSION This machine adjusts the thread tension automatically when pattern is selected However you can change the thread tension as follows 1 Press the fuction F5 button directly under the tension mark LCD changes to the thread tension mode 2 To increase the upper thread tension press the function F5 button To decrease the upper thread tension press the function F4 button Pre set tension number is highlighted The mark wy is indicating the absolute thread tension By pressing the function F3 AUTO or cle
55. selected stitch as follows a Regular stitch normal stitch b Mirror stitch reverse left and right c Reverse stitch reverse front and back d Mirror and Reverse stitch If the mark is not indicated the pattern cannot change to mirror or reverse stitch When you pressed clear C button machine will return to regular stitch also elongation will return to regular length 22 EDT mM m J J J 14 lt gt I J mt gt i i J at F2F3FA4F5 40414 VN D ELONGATION Some patterns may be elongated from the original length You may elongate the pattern by pressing the function button F3 directly under the elongation icon a Regular length b Elongated A pattern cannot be elongated if the elongation icon is not indicated When you pressed clear button machine will return to regular length also mirror reverse will return to regular stitch E SETTING STITCH WIDTH AND LENGTH Machine will set the stitch width and length suitable for the pattern 1 You can make changes by pressing the function button F4 directly under the width and length mark 2 LCD will change to show the stitch width and length For narrower width press function butto
56. st point 2 Loosen the needle clamp screw 3 Remove the needle 4 Insert new needle into needle clamp with the flat side to the back and push it up as far as it will go 5 Tighten the needle clamp screw a Do not use the bent or blunt needle Place needle on a flat plate and check straightness FABRIC THREAD AND NEEDLE TABLE Select size of thread and needle in accordance with fabric to be sewn Type of Fabric Thread Size Needle Type Needle Size Light Weight thin georgette organdy voile taffeta silk etc Ctn 80 100 Silk 60 80 Syn 80 100 2000 gray shank 9 70 11 80 Medium Weight gingham pique linen cotton satin thin corduroy velvet Ctn 50 80 Silk 50 50 80 2000 gray shank 11 80 14 90 Heavy Weight gabardine tweed denim corduroy 40 50 Silk 50 50 60 2000 gray shank 14 90 16 100 Stretch double knit tricot spandex jersey Syn 50 80 Silk 50 Polyester 2001 green shank 11 80 14 90 Needle for knit and synthetic fabric Sweatshirt Swim wear Double Knit Sweater Knit Polyester 2001 green shank Leather 2032 Leather Use a Singer brand needle for
57. t side of fabric b Wrong side of patch 2 Lower the buttonhole lever and sew buttonhole See previous page Machine will sew the buttonhole in the order as shown and stop automatically after sewing 3 Press the thread cutter button and raise the presser foot to remove the fabric 4 Carefully cut through the center of buttonhole to within 3 mm of each end Cut diagonally to each corner as shown Remove the basting 5 Draw the patch through the opening to the underside 6 Turn the fabric and pull the patch through the buttonhole rectangle Press the patch c Wrong side of fabric d Right side of patch 7 Turn the patch and press the side seam allowance 8 Fold each side of the patch to form pleats that meet at the center of the buttonhole and cover the opening Press the patch 9 Turn the fabric to right side and baste along the center of each fold a Right side of fabric 36 10 Fold the fabric and stitch along the seams on each side just a needle width from the original stitching line Remove the basting c Wrong side of fabric 11 Fold the fabric along the buttonhole end and stitch triangular ends on the original stitching line 12 Press and trim the patch to within 5 mm of the stitching a Right side of fabric c
58. to spiral of rolled hem foot Move fabric back and forth until the fold forms a scrolled shape 3 Lower the presser foot and start sewing slowly while guiding raw edge of fabric scroll evenly into front of rolled hem foot CORDING No 9 Zigzag Stitch for Single Cording No 12 Multi Zigzag for Triple Cording Cording Foot A SINGLE CORDING 1 Set stitch pattern to No 9 Insert the cord in the center groove of cording foot from the right side opening Pull cord about 5 cm 2 inches behind the foot 2 Adjust the stitch width so that the stitches are just cover the cord Lower the foot and sew slowly guiding the cord B TRIPLE CORDING Set the stitch pattern to No 12 and set the stitch width to 6 0 7 0 Insert three cords into the slots of cording foot 40 5cm CONTINUOUS DECORATIVE PATTERN Use the satin foot for continuous decorative stitch patterns This foot has a full indentation on the underside to easily allow closely spaced zigzag stitches and fabric to feed freely under foot No 19 100 Satin foot B To tailor the continuous decorative stitch pattern you may adjust the length and width of pattern Also you may change reverse or mirror stitch of pattern and elongate the pattern
59. uirements of the CISPR The wires in this mains lead are colored in accordance with the following code Blue neutral N Brown live L As the colors of the wires in the mains lead of this appliance may not correspond with the colored markings identifying the terminals in your plug proceed as follows The wire which is colored blue must be connected to the terminal which is marked with the letter N or colored black The wire which is colored brown must be connected to the terminal which is marked with letter L or colored red Ifa 13 Amp BS 1363 plug is used a 3 Amp Fuse must be fitted or if any other type of plug is used 5 Amp fuse must be fitted either in the plug or adaptor or at the distribution board Neither cord is to be connected to the earth terminal of a three pin plug ce Z appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use or the appliance by a person responsible for their safety 2 Children should be supervised to ensure that they do not play with the appliance MAIN PARTS 1 Handle 2 Top Cover 3 Thread Take Up Lever Inside 4 Face Plate 5 Thread Cutter Button 6 Speed Control Button 7 Needle Up Down Slow Button 8 Reverse Stitch Button 9 Start Stop Button 10 Extension Ta
60. upper and bobbin threads to the left 3 Position fabric under presser foot so that the starting point comes depth side Lower the foot b Sewing bar tack on edge of thick fabric such as pocket place same thickness fabric or cardboard beside the fabric V TA CN 07 4 Lower the buttonhole lever completely now LX N V Note Machine will not start to sew if buttonhole lever is not lowered properly or buttonhole foot is not positioned correctly 5 Hold upper thread lightly and start the machine 102 D 6 Machine will sew bar tack or darning stitch as i il shown Machine will stop automatically when li the pattern is finished it WANN Co T Press the thread cutter button and raise the presser foot lifter to remove the fabric 38 SEWING ON BUTTONS No 13 Button Sewing Foot 1 Lower the feed dogs by moving the drop feed lever to the left 2 Attach the button sewing foot Align two holes of the button with slot of presser foot and lower foot to hold the button securely 3 Adjust the stitch width so that the needle enters the left hole of button 4 Turn hand wheel by hand so needle enters the second hole You may need to adjust the stitch width again Zu To prevent accidents Make sure that the needle does not hit the button during sewing Otherwise needle may break 5 Se
61. utton is pressed If upper thread is not threaded machine will stop after a few turns Upper thread sensor Note When the foot controller is connected start stop button will be deactivated B REVERSE STITCH BUTTON The machine will continue to sew in reverse at low speed while this button is pressed and stop when this button is released Note When the foot controller is connected machine will sew in reverse while this button is pressed When released machine will sew forward C NEEDLE UP DOWN SLOW BUTTON Pressing this button when the machine is stopped will change the needle position from down to up or from up to down While sewing by pressing this button machine will sew in slow speed Pressing this button again the speed will return D SPEED CONTROL BUTTON The machine will sew faster when the button is slid to the right and sew slower when the button is slid to the left Note When the foot controller is connected this button limits the maximum speed E PRESSER FOOT LIFTER The presser foot is lifed up or down by this lever Note Machine will not start when the presser foot is lifted Except for bobbin winding F THREAD CUTTER BUTTON Press this button after sewing to cut the upper and bobbin threads The machine will cut both threads automatically CAUTION 1 Do not press this button when there is no fab
62. w approximately 10 stitches at slow speed 6 Raise the foot and cut the threads remaining about 10 cm to the fabric 7 Pull the end of bobbin thread and pull upper thread to the wrong side of fabric Tie them together 8 After sewing move the drop feed lever to the right Note To sew a 4 hole button follow the procedure above for the first two holes Then lift presser foot slightly and move fabric to permit stitching the other two holes either independently or criss cross over the first two holes A Thread Shank Buttons on coats and jackets should have a thread shank to make them stand away from the fabric Insert a straight pin or sewing machine needle under the center slit of the foot from the front Sew over the pin or needle Pull thread to back of button and wind around stitches to form a firm shank Tie thread ends Securely Du cs 39 NARROW HEMMING No 1 Straight Stitch Center Needle Position Rolled Hem Foot 1 Fold edge of fabric over about 3 mm 1 8 inch then fold it over again 3 mm for about 5 cm 2 inches along edge of fabric 2 Insert needle into the fold by rotating the hand wheel toward you and lower the presser foot Sew several stitches and raise the presser foot Insert fabric fold in

Singer 9910 Sewing Machine User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents