Perlick HA24 Beverage Dispenser User Manual
Contents
1. 22 82 He ina re a UN VU O el p Figure 2 24 Anti tip Kit 23 He 4 Figure 3 48 Anti tip Kit reg PERLICK RESIDENTIAL INSTALLATION MANUAL PREPARING THE SPACE A CAUTION If the unit is to be installed under a countertop it is recommended that the countertop be supported by a structure other than the unit itself to prevent damage to the unit A CAUTION Make sure the floor under the unit is level with the surrounding finished floor Protect a finished floor with plywood cardboard or some other suitable material before moving the unit into place Failure to do this may result in damage to the floor 1 Make sure the space opening is correctly sized for the unit See chart below for finished rough opening requirements HP15 15 Signature Series 34 3 8 minimum 24 15 35 1 2 maximum HP24 24 Signature Series 34 3 8 minimum 24 24 35 1 2 maximum HP48 48 Signature Series 34 3 8 minimum 24 48 35 1 2 maximum HC24 24 C Series 34 3 8 minimum 24 24 35 1 2 maximum HA24 24 ADA Compliant Series HH24 18 Shallow Depth Series NOTE For a cabinet door to open properly the door must open a minimum of 90 Use a minimum 3 filler in corner installations to assure a full 90 opening Allow 25 clearance in front of unit for full door swing and shelf drawer pull out for all units e perlick com 22. Check that the following are level and square Front and interior opening Installation opening and floor surface Countertop bottom front edge NOTE The floor under the unit must be at the same level as the surrounding finished floor A CAUTION To prevent possible damage to the countertop do not place heavy objects on countertop directly over unit INSTALLING THE UNIT 1 Plug the unit into the 15 amp grounded electrical outlet located within the installation opening With power applied to the unit check that the lighting and cooling functions operate properly Turn off the power to the wall outlet at the circuit breaker 2 With all surfaces in the installation opening sguare and level refer to Figure 4 on page 7 and perform the following steps to level the unit At the front of the opening measure from the floor to the bottom of the front edge of the countertop Measure from the floor surface to the top of the unit at the rear corners Adjust the unit legs so these two measurements are egual Using an adjustable wrench or pliers turn legs clockwise to lower the unit or counterclockwise to raise it NOTE Legs should not extend more than 3 4 from the bottom of the unit 3 Slide the unit into position in the opening Make sure the rear leveling legs slide under the ant tip brackets Push the unit into the opening until the bottom front edge of the unit is flush with the surrounding cabinetry or unti
3. be used to compensate for floor differences exceeding 1 2 INSTALLATION Unit may tip forward if loaded racks shelves are all pulled out at the same time To prevent tipping and to provide stable installation the unit must be secured in place with the anti tip brackets supplied with the unit The anti tip brackets when properly installed should secure the rear legs glides to the mounting surface and prevent the unit from tipping forward NOTE Anti tip brackets are only used for stationary cabinets and should not be installed on cabinets with accessory casters Caster kits are available for HP HC and HA model cabinets Refer to the instructions supplied with the caster kit for proper installation 13 42 L Ho Ye Figure 1 15 Anti tip Kit 1546 22 9 PERLICK RESIDENTIAL INSTALLATION MANUAL PIEN NOTE If installing on a concrete floor concrete fasteners are reguired and not included with the anti tip kit NOTE Some installation sites may reguire modifications to provide a secure surface for attaching the brackets A set of anti tip brackets is supplied with the unit These brackets should be attached to the floor at the rear of the unit Each bracket must be located to engage the rear glides when the cabinet is pushed back into position Refer to Figures 1 2 and 3 shown below for anti tip bracket mounting locations
4. latch into the latch catch on the unit Figure 5 A CAUTION The toe plate must be removed to service the unit The floor cannot interfere with removal and the louvered sections must not be covered or obstructed Obstructions could prevent proper air circulation which may damage the unit NOTE To achieve maximum performance interior louver openings and fan guard openings should never be obstructed Figure 5 Toe Plate Installation perlick com PERLICK RESIDENTIAL INSTALLATION MANUAL SHELVING DRAWER ADJUSTMENTS A CAUTION Completely empty shelf or drawer before removing Pull the shelf drawer out to its furthest position Locate the tabs in the middle of both extenders Lift one tab up while pushing the opposite tab down and pull shelf drawer out Figure 6 2 Position each bracket separately Graso the middle of the bracket pull the front end up and out then forward to remove it 3 Place bracket at desired location Push the bracket rear hook into the rear mounting slot then set front of the bracket in the front slot 4 Repeat for other brackets 5 Push extenders completely into brackets Align the shelf drawer grooves with the extenders and slide completely into the unit Lift one tab on extender UP while pushing tab on opposite extender DOWN and pull out to remove To remove brackets remove shelf lift front of bracket to disengage t
5. of the Perlick product and may not be assigned or transferred PERLICK RESIDENTIAL INSTALLATION MANUAL This Warranty does not apply to Damage to Products occurring during transportation Products that are used in a manner that is not normal residential or light commercial use Products that are improperly installed misused or abused operated with low voltage wired in a manner not conforming to electrical codes not properly operated in accordance with Perlick s instructions not cleaned or maintained in accordance with Perlick s instructions modified or damaged by lightning or other acts of nature Consumable items such as light bulbs Cosmetic damage Adjustments to controls door reversal cleaning the condenser or other routine maintenance Products for which the original proof of purchase delivery date or serial number cannot be verified Products for which the defective parts are not returned for inspection if requested by Perlick Damage to other property caused by the products including but not limited to loss of food due to spoilage and damage caused by water leakage THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER WARRANTY EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE PROVIDED HOWEVER THAT TO THE EXTENT REQUIRED BY LAW MPLIED WARRANTIES ARE INCLUDED BUT DO NOT EXTEND BEYOND THE DURATION OF THE EXPRESS W
6. residential products service support warranty registration OTHER TERMS AND CONDITIONS This Warranty applies only to products installed in the fifty states of the United States the District of Columbia and the ten provinces of Canada To obtain the warranty coverage described in this Warranty Perlick or its authorized distributor or dealer must receive written notice of the warranty claim within the applicable warranty period To receive parts and or service and the name and telephone number of the nearest Perlick authorized service representative please contact your Perlick dealer or distributor or Perlick s Customer Service Department by writing to it at Perlick Corporation Attn Customer Service Department 8300 West Good Hope Road Milwaukee Wisconsin 53223 or by calling Perlick s Customer Service Department at 800 558 5592 or by e mailing Perlicks Customer Service Department at warrantyserv perlick com In addition you can notify Perlick of a warranty claim by visiting Perlick s website at http www perlick com residential products service support and filling out and submitting the Technical Service Reguest form that appears there All service provided by Perlick under this Warranty must be performed by Perlick s authorized service representatives unless otherwise specified by Perlick in writing Service will be provided during normal business hours This Warranty applies only to the original retail purchaser
7. ALLATION MANUAL kan 5 Using the screws removed in step 3 install the top and bottom hinge brackets from the kit Fig 9 Hinge brackets and mounting screws Hinge brackets and mounting Screws Figure 9 Hinge Installation 6 Remove the top and bottom door hinge brackets and the push plunger brackets Fig 10 Retain the screws for later use Hinge brackets and mounting screws Figure 10 Door Brackets perlick com 9 Prick PERLICK RESIDENTIAL INSTALLATION MANUAL 7 Remove the front panel from the door assembly by removing the inner mounting screws 4 per side from the perimeter of the door assembly Fig 11 Rotate the front panel 180 The top becomes the bottom Reattach using the same screws and mounting holes Front panel Corner screws need not be removed to remove front panel Figure 11 Removing Front Panel 8 Remove the Perlick nameplate from the door front using a plastic putty knife Fig 12 Install the new Perl nameplate included in the kit Nameplate ick Figure 12 Nameplate perlick com 9 Insert the bearing into the door hinge bracket Fig 13 10 Insert the V block into the door bottom hinge bracket and attach with the e clip Fig 13 Note the orientat
8. ARRANTY FIRST SET ABOVE PERLICK S SOLE LIABILITY AND YOUR EXCLUSIVE REMEDY UNDERTHIS WARRANTY ARE SET FORTH INTHE PARAGRAPH ENTITLED REMEDY SET FORTH ABOVE ERLICK SHALL HAVE NO LIABILITY WHATSOEVER FOR NY INCIDENTAL CONSEQUENTIAL OR SPECIAL DAMAGES RISING FROM THE SALE USE OR INSTALLATION OF THE RODUCT OR FROM ANY OTHER CAUSES WHATSOEVER WHETHER BASED ON WARRANTY EXPRESS OR IMPLIED OR OTHERWISE BASED ON CONTRACT TORT OR ANY OTHER THEORY OF LIABILITY IN NO EVENT SHALL PERLICK S LIABILITY WITH RESPECT TO A PRODUCT EXCEED TH PURCHASE PRICE OF THE PRODUCT Some states do notallow limitations on howlong an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This Warranty gives you specific legal rights and you may also have other rights which vary from state to state perlick com rpg PERLICK RESIDENTIAL INSTALLATION MANUAL SAFETY PLEASE READ all instructions completely before attempting to install or operate the unit Take particular note of the DANGER WARNING and CAUTION information in the manual The information is important for the safe and efficient installation operation and care of your Perlick unit Indicates a hazard that WILL result in serious injury or death if precautions are not followed A WARNING Indicates a hazard MAY cause seri
9. Rick OUALITY amp INNOVATION THAT INSPIRES Installation Manual HP15 HP24 HP48 HC24 HA24 HH24 15 SIGNATURE SERIES 24 SIGNATURE SERIES 48 SIGNATURE SERIES CERES ADA COMPLIANT SERIES 18 SHALLOVV DEPTH SERIES Form No Z2348 Rev 04 01 2014 PERLICK RESIDENTIAL INSTALLATION MANUAL TABLE OF CONTENTS Warranty Information Safety INFOMMATION ams Plumbing Electrical and General Information 4 Installation INStrUCtiONS suunnan 5 Toe Kick Installation issn 7 Shelving Drawer AdjUStMENTS a 8 CONGRATULATIONS Congratulations on your purchase of a Perlick high quality residential refrigeration product Perlicks innovative product offering gives you the opportunity to enjoy the functionality and user friendliness in just about any room of your home including kitchens bedrooms entertainment rooms basements and even bathrooms All Perlick products are built with commercial grade stainless steel providing you with the beauty and durability for a lifetime of use This installation guide will show you how to properly install your new perlick product We dedicate considerable time to ensure that our products provide the highest level of customer satisfaction If however service is reguired call Perlick at 800 558 5592 For your own protection never return merchandise for credit without our approval We thank you again for selecting a high guality Perlick product We hope y
10. ce Maker or a factory second B Stock product The one 1 year period commencing on the date of purchase by the original retail purchaser The Extended Warranty Period applies only to the hermetically sealed refrigeration system contained in Perlicks undercounter refrigerators The Extended Warranty Period is the portion of the six 6 year period commencing on the date of purchase by the original retail purchaser that is not covered by the Basic Warranty Period IMPORTANT Read and understand all information in this manual before attempting the installation All plumbing and electrical work must be performed by a qualified technician and conform to all applicable state and local codes perlick com REMEDY Perlick will provide the parts and labor necessary to repair or replace at Perlick s option any parts proven to be defective in material or workmanship during the Basic Warranty Period Perlick will provide the replacement parts but not the labor for any parts of the hermetically sealed refrigeration system proven to be defective in materials or workmanship during the Extended Warranty Period The cost of freight to ship the replacement parts will be paid by Perlick Replacement parts are warranted for the remainder of the original warranty period or ninety 90 days whichever is longer REGISTRATION Your Perlick product can be registered via the online Warranty Registration form at http wwwperlick com
11. dry reinstall with fasteners 41132 41132 E 58 MH m ill 4 Z 17132 J 1 8 x 5 16 DEEP pie 112 m BREAK ALL i EDGES Figure 18 Wine Rack Trim 15 models 95 66 8 17 32 8 17 32 1 8 x 5 16 DEEP 5 8 mal 1417 T 1 i i 8 71 4 ili 117 82 5 8 1 pte 1z 18 5 16 BREAK ALL OUTSIDE EDGES Figure 19 Wine Rack Trim 24 models Prick QUALITY amp INNOVATION THAT INSPIRES Use and Care Guides Specification Sheets Wood Overlay Templates for Doors Drawers and Grilles and Corresponding Compliance and Energy Guides are available for download at www perlick com residential products service support Contact Perlick Customer or Technical Service at 800 558 5592 Customer Service and Technical Service are available business days Monday through Friday from 8 a m to 4 30 p m CST PROUDLY MADE CERI USA 8300 W Good Hope Road Milwaukee WI 53223 800 558 5592 info perlick com www perlick com Form No 22348 Rev 04 01 2014
12. he front key slot then pull forward to disengage the rear key slot Figure 5 Shelving Drawer Adjustment e perlick com DOOR OPTIONS Perlick residential units offer a variety of door panel design alternatives solid stainless steel solid wood overlay glass with stainless steel trim and glass with wood overlay trim Solid stainless steel and stainless steel glass doors are shipped from the factory with decorative stainless steel panels and handles in place on the unit Solid wood overlay and glass wood overlay doors are designed to accept a decorative front panel to match surrounding cabinetry and door handles NOTE Wood overlay models are designed to accept wood overlay panels from your cabinetry supplier They do not include a wood overlay Templates are available on www perlick com residential products Click on Service amp Support and then choose Wood Overlay Templates from the menu Take care in choosing the correct template for your specific model The handle is supplied by the customer All Perlick units excluding beer dispenser and ice maker models accept any of the above door configurations and are fully interchangeable Glass door configurations are not available on beer dispenser or ice maker models NOTE Glass with stainless steel trim and glass with wood trim may sweat in conditions with relative humidity over 75 CHANGING DOOR SWING DIRECTION NOTE Changing the door m
13. ion of the V block Bearing in door top hinge bracket Orientation oT V block BOTTOM VIEW Figure 13 Bearing and V Block 11 Attach the top and bottom hinges and push plunger using screws removed in step 6 Fig 14 Top hinge and screws Bottom hinge and screws Figure 14 Door Hinges 12 Place the lower V block into the lower cabinet hinge with the notch parallel to the cabinet Fig 15 V block parallel to cabinet Ne TOP VIEW Figure 15 Installing V Block 13 Lift the door assembly and insert the top pin into the bearing Move door toward cabinet and align the V blocks Fig 16 SS e s s SS Insert top pin into bearing PI J Insert and tighten hinge pin Figure 16 Installing Door 14 Insert and tighten the lower hinge pin to complete the assembly PERLICK RESIDENTIAL INSTALLATION MANUAL HANDLE INSTALLATION The handle mounting on the wood overlay should be mounted on the overlay only not the actual door to avoid damage to the factory door 1 Handle must be attached to the overlay before mounting the overlay onto the door Mark the rear of the wood overlay pane
14. l the rear legs are tight against the anti tip brackets 4 Shim the front of the unit so the front face is flush with the surrounding cabinetry Adjust the front legs to support the countertop at the shimmed height Using an adjustable wrench or pliers turn the legs clockwise to lower the unit or counterclockwise to raise it Countertop should be resting on top of the unit NOTE Countertop should be resting evenly on entire top of the unit Shim if necessary to prevent damage to the countertop Measure front of opening from floor surface to bottom edge of countertop K Measure at both rear corners of unit from floor surface to bottom of countertop Figure 4 Leveling the Unit 5 Check interior door openings to make sure the unit is level and square Install shelving and or drawers Place the slide brackets squarely into the bracket grooves When installed properly a click should be heard from the slide bracket retaining tabs and the brackets should slide smoothly The retaining tabs will stop the shelf drawer when pulled out to full extension 6 Turn on the power to the wall outlet at the circuit breaker NOTE Improper shelf drawer installation may not actuate slide mechanism PERLICK RESIDENTIAL INSTALLATION MANUAL TOE PLATE INSTALLATION Once the unit is secured in place install the louvered toe plate Secure the plate by snapping the
15. l with handle fastening locations 2 Drill through the wood overlay panel at marked locations taking care not to damage the panel 3 Countersink screw heads so that screw heads are flush with the back side of the panel Attach the handle to the overlay panel A CAUTION Proper woodworking materials and equipment should be used to avoid damage or errors in workmanship DOOR LOCK INSTALLATION NOTE Full size lock installation wood overlay panel templates are available on the Perlick website Visit www perlick com Residential click on Service amp Support and then choose Wood Overlay Templates from the menu Lock templates are available for all HP HC HA and HH series models Take care in choosing the correct template for your specific model When installing to a wood overlay perform the lock installation before mounting the wood overlay to the door 1 See Figure 17 below Attach mounting bracket to wood overlay 2 Insert lock body and attach with nut Mounting bracket Nut Lock strike Lockwasher Lock body sy Figure 17 Installing Door Lock perlick com PERLICK RESIDENTIAL INSTALLATION MANUAL WOOD OVERLAY INSTALLATION FOR 2 AND 4 MODELS Before beginning installation check all components for proper fit and finish Scan the OR code to the right with your smart phone to watch a detailed how to video on installing a wood overlay panel onto Pe
16. onal Electrical Code and any local codes or ordinances when installing the receptacle All Perlick units come equipped with a NEMA 5 15P 90 plug with a 5 cord extending beyond the rear of the cabinet The electrical outlet must be flush with or recessed into the wall surface for all HP HC and HA models HH models have a recess at the rear of the cabinet to accomodate the plug and keep a true 18 depth A CAUTION Do not attempt to operate the equipment on any other power source than that listed on the Electrical Specification Plate attached to the unit A DANGER Serious Electrocution Hazard Electrical grounding is required This appliance is equipped with a 3 prong grounding polarized plug for your protection against possible shock hazards Failure to comply with these electrical guidelines may result in possible death or serious injury fire or loss of property Never remove the round grounding prong from the plug Never use a 2 prong adapter Never use extension cord to connect power to the unit Ifa2 prong receptacle is encountered or a longer power cord is required contact a qualified electrician to have it replaced in accordance with applicable electrical codes ADDITIONAL GENERAL INFORMATION All electrical instructions assume the outlet is located 4 10 above the floor surface Floor must be level in area of installation Leg levelers are used for fine tune adjustment only and should not
17. ou enjoy using it Model Number Serial Number Purchase Date Dealer Name Address Phone Number Year c US Oiar Door IA MAO esessssssesssssussssssesssesstssssssssssssseusssssasssessnsssee 8 Changing the Door Swing Direction 8 Handle Installation ae Door Lock Installation Wood Overlay Installation WINeReicekimz da PERLICK RESIDENTIAL PRODUCTS WARRANTY WARRANTY Perlick Corporation Perlick warrants to the original retail purchaser that during the Basic Warranty Period Perlick s products will be free from free from defects in material and workmanship and during the Extended Warranty Period the hermetically sealed refrigeration system contained in Perlick s undercounter refrigerator will be free from defects in material and workmanship This system consists entirely of the compressor condenser drier connecting tubing evaporator and hot gas bypass valve The Basic Warranty Period is as follows For a new product or floor display model other than the H50IM Clear Ice Maker The three 3 year period commencing on the date of purchase by the original retail purchaser except that the Basic Warranty Period will be the two 2 year period commencing on the date of purchase by the original retail purchaser if the purchase of the product is not registered with Perlick within ninety 90 days of purchase in the manner described below Forthe H50IM Clear I
18. ountis not advisable if the door is equipped with a custom wood overlay Doing so may result in an undesirable handle position To change the door swing direction a hinge kit is required Part No 67439R Right hinge kit Part No 67439L Left hinge kit In addition to the hinge kit the following tools are required Large flat head screwdriver Regular Phillips head screwdriver Plastic putty knife 1 Support the door in the open position as shown in Fig 7 on page 9 Remove the hinge pin 2 Pull door to the side and then lower door cy 4 3 Remove top and bottom hinge brackets Retain screws for later use See Fig 8 on page 9 x 4 Remove the hole plugs from the top and bottom hinge bracket mounting holes see Fig 8 on page 9 Place the plugs in the holes on the opposite side made vacant by removing the hinges in step 3 SUPPORT Pull door to the side then lower door Remove hinge pin Figure 7 Door Removal Hole plugs Hinge brackets and mounting screws TI o O o gt SS SS eet Hinge brackets and mounting screws Figure 8 Hinge Removal PERLICK RESIDENTIAL INST
19. ous injury or death if precautions are not followed A CAUTION Indicates a hazard where minor injury or product damage may occur if precautions are not followed PRIOR TO INSTALLATION Carefully inspect cabinet for hidden damage If damage is discovered file your claim immediately with the transport company Perlick is not responsible for damage in transit A CAUTION When moving the unit be sure to protect finished flooring with appropriate material to avoid damage from moving the unit IW inated Do not lift unit by drawer shelving or door handles as damage to the unit could occur if not moved as instructed A WARNING Di prevent personal injury a inimum of two people are required to lift the unit Larger units may require additional personnel Before moving the unit secure the door shut with tape to prevent door from swinging open while being moved Carefully move unit to installation site and place in front of opening A CAUTION If unit has been laid on its back or sides place unit upright and allow minimum of 24 hours before connecting power E perlick com PLUMBING No plumbing connections are required Condensate from the cooling coil is automatically evaporated through a condensate pan located in the condensing section of the unit ELECTRICAL A 115 volt 60 Hz 15 amp circuit breaker and electrical supply are required A separate circuit is required for each Perlick unit installed Follow the Nati
20. rlick doors Otherwise follow these written instructions A CAUTION All overlay doors reguire a trim p anel of at least 3 4 thick The solid wood and glass wood panels should not weigh more than 10 Ibs 1 With the unit secured in position open the door and make sure panel pre drilled holes align with door frame holes 2 Loosely attach four corners of overlay panel to the door using 10 x 1 wood screws installed through the door frame from the rear 3 Check for overall wood overlay panel fit position and function Make minor adjustments as necessary When panel is properly aligned tighten mounting screws securely Install the rest of the mounting screws and tighten securely A CAUTION Do not overtighten wood overlay attachment screws as this may damage the factory supplied door frame perlick com WINE RACK TRIM OPTIONAL All wine reserve racks come with sleek stainless steel fronts Unfinished solid hardwood fronts are optional and can be removed and replaced with other wood to match your cabinetry See Figure 18 and 19 for wine rack face details NOTE The unfinished faces should be finished and sealed In many cases stains and or finishes have odors that may be objectionable in an enclosed area Do not stain or finish wood faces while installed on unit To remove the front wood face from the wine shelf simply pull out the wine shelf and remove the fasteners finish as desired and when completely
Download Pdf Manuals
Related Search