Outlaw Audio 200 M-Block Stereo Amplifier User Manual
Contents
1. When making connections with the RCA type plugs on interconnect cables make certain to gently but firmly insert them into the jacks on the back of the Model 200 Loose connections can cause intermittent sound and may dam age your speakers The barrel assembly of some high quality RCA plugs may be very tight and it is important to ensure a proper connection between the interconnect cable and the input jack AC Power Connection The final step in the installation of the Model 200 is to connect the power cord First connect the female end of the cord into the AC Power Receptacle on the rear panel Once the cord as been firmly connected to the Model 200 insert the plug end into an AC power outlet Safety Notes m Due to the current draw of the Model 200 DO NOT connect the power cord to the accessory outlet of an audio video component m Should the power cord become lost or damaged be certain to replace it with a replacement that meets or exceed the original specifications Use of power cords with insufficient capacity such as those used with computers or office equipment may create a safety hazard Owner s Manual Operation Operation Operation of the Model 200 is simple In normal use there are no controls to adjust once the installation is complete After all connections have been made to the amplifier s inputs and speaker terminals have been made and the AC power cord has been connected the way in which the unit tu2. fuse be certain to replace it with an identical type Should the fuse continue to blow discontinue use of the Model 200 and disconnect it from both AC Power and all source components Contact Outlaw Audio for service information Outlaw Service Information The Model 200 does not contain any user serviceable parts If you suspect a problem that may require service assistance contact us via e mail at custome rservice outlawaudio com or by phone at 866 OUTLAWS 688 5297 It is important that an authorized service agent carry out any repairs This will ensure proper service and preserve the protection of your Limited War ranty Keep your sales slip or receipt in a safe place with this manual so that it will be available to verify the purchase date should you experience a problem covered by our warranty Solutions Master Power Switch turned off No power light LED Turn on Master Power Switch Amplifier will not turn on Remote trigger cable not properly connected Verify connection of trigger cable at both ends Amplifier turns on but no audio is heard Input plug not connected properly or is loose Check input connection No audio Speaker not connected properly Check speaker connections at amp and speaker Audio levels differ from other channels in the system Improper settings or output levels from the processor or controller Check the settings on your preamp processor or controller Audio plays the
3. speakers and much more The Model 200 is compact yet powerful delivering 200 watts at eight ohms 20Hz 20KHz gt 0 05 THD Thanks to a unique circuit design and a heavy duty power supply with a horizontally oriented torroidal transformer the Model 200 operates without a fan despite the deep power reserves Since the Model 200 will often be used in multiple unit systems a variety of power control options are provided In addition to a standard power on off switch the Model 200 may be operated from the external trigger control of compatible products such as the Outlaw Model 950 Both in and out trigger jacks are provided so that the control signal may be cascaded For systems where an external trigger is not available the Model 200 s music sense circuitry is available for automatic turn on whenever an audio signal is present In order to fully enjoy the performance of your amplifier please take a few minutes to read this owner s manual It contains important information that will help you to make certain that the amplifier is properly configured for operation with the rest of the equipment in your system Once again welcome to the Outlaw family Features m High power M Block amplifier m Unique dual topology circuit design m Music Sense circuitry and low voltage trigger connection for automatic turn on m Five way binding posts accommodate large gauge speaker cable m Fan free convection cooling m Efficient power supply with
4. the ground circuit The safest and most reliable approach may be to provide your own ground This can be accomplished by having a licensed electrician drive at least five feet of copper jacketed steel grounding rod into the earth and using that for your grounding connection Suggestion 5 If you have hum in your video display device bars that roll up through image at 12 14 second intervals this may be related to hum you also experience in your audio system The previous suggestion tips may help with this also If not try isolating the ground in the projectors video signal cable with a base band video isolation transformer such as the Jensen VB 1BB If the hum persists after all of the above suggestions have been tried contact the Outlaw Audio customer service department for assistance El Outlaw Audio Specifications Power Output 200 watts 8 ohms 20 Hz 20 kHz lt 0 05 THD 300 watts 4 ohms 20 Hz 20 kHz lt 0 05 THD THD Signal to Noise 100 dB un weighted Trigger Input 6 35V DC 4mA Operating Mode Class G AB Input Impedance gt 10K Ohms Gain 274dB 1 7V sensitivity for full output Input Connector RCA Jack Output Connectors Five Way binding posts Power Consumption 600 watts maximum lt 3 watts standby Weight 18 pounds 8 165 Kg Dimensions H W D 1 5 x 17 x 11 5 40mm x 430 mm x 330 mm Note Due to our policy of continual improvement all specifications are sub
5. to be enclosed in a cabinet or rack make certain there is adequate air circulation Sufficient ventilation should be provided so that hot air may exit and cool air may enter the cabinet In some instances a small cooling fan may be required to insure adequate airflow through the cabinet If you are in doubt as to the ventilation requirements for your specific installation please contact us Also do not place the amplifier directly on a carpeted surface as this will inhibit airflow underneath as well as create a potential fire hazard Avoid installation in humid locations in extremely hot or cold locations or in areas that are exposed to direct sunlight or space heating equipment Loudspeaker Ratings Your Outlaw Power Amplifier has adequate power to drive most loudspeakers without producing any distortion Most modern speakers are rated at four to eight ohms nominal impedance but within some frequency ranges the impedance may drop to two ohms The Outlaw is designed with ample power reserves to protect you from experiencing any problems at these low impeadances unless you demand excessively high volume levels Due to the high power output capability of your power amplifier it is important that it not be used with speakers not capable of handling the amplifier s power output Before using the amplifier for the first time make certain that your speakers are capable of handling its rated power output at the impedance rating of your sp
6. Model 200 M Block Power Amplifier ontiaw Oak VENE Owner s Manual Warnings Please Read First CAUTION N RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To reduce the risk of electric shock do not remove the cover or back No user serviceable parts inside Refer to qualified personnel WARNING To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture The lightning flash with arrowhead within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous volt age within the products enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating maintenance servicing instructions in the literature accompanying the appliance Precautions Verify The Line Voltage Your new amplifier has been factory configured for 120 3 volt AC lines Connecting the amplifier to a line voltage other than that for which it is intended can create a safety and fire hazard and may damage the amplifier If you have any questions about the volt age requirements for your specific model or about the line voltage in your area contact Outlaw Audio before plugging the unit into a wall outlet Verify AC Circuit Capacity The high power output of your Outlaw amplifier may require heavy power dra
7. ady to turn on when a control signal is received at the trigger jack or from the music sense circuitry Green Indicates that the Model 200 is on and operational Red Indicates that the Model 200 is in the Protect mode If the LED is red you should turn the unit off and then check for the source of the condi tion that caused the overload This may be a shorted speaker lead or other similar condition In the event of repeated appearance of the red LED you may have a chronic system failure with either the Model 200 or another component in your system In this case disconnect the Model 200 from AC power and the rest of your system and consult Outlaw Audio s Customer Service Department for assistance Input jack Connect this jack to the output of the source used to feed the Model 200 Note that if the Trigger Mode switch is turned to Music the Model 200 will turn on whenever an audio source is present at this jack Trigger Input Jack Connect this jack to the trigger output jack of a compatible product such Jack of an additional Model 200 Note however that connecting more than two Model 200s to a single source controller may overload the system and is not recommended If you wish to automatically turn on more than two Model 200 units we recommend the use of either the music sense circuitry or an externally powered relay controller Contact Outlaw Audio Customer Service for more information on using the Model 200 in multiple unit syste
8. c m Make sure the AC Power Switch is turned on Note that the front panel LED will turn amber indicating that the unit is in the Standby mode awaiting a signal that will activate the operational mode In this configuration the Model 200 will automatically turn on whenever it is receiving an audio input signal The unit will return to the standby mode a few minutes after the audio signal stops Speaker Wire Connections It is always best to connect the amplifier to your speakers using high quality cable The Model 200 is equipped with five way binding post terminals that accept bare wire spade lugs or banana type plugs when they are permitted by local safety agencies Once you have located the proper speaker terminals for the type of output configuration in use connect your speakers using the following guidelines To assure that the high quality signals produced by your Model 200 are car tied to your speakers without loss of clarity or resolution we recommend that you use high quality speaker cable Many brands of cables are available your choice may be influenced by a number of factors i e the distance between your speakers and the amplifier the type of speakers you use personal prefer ences and other factors Regardless of the brand or type of cable selected we recommend using a cable constructed of fine multi strand copper with a gauge of 14 or larger Remember that in specifying cable the lower the number the thicke
9. cost and ask for your authorization to perform said repairs You must pay shipping charges incurred in getting your Product to the factory We will pay the return shipping charges if the repairs are covered by the warranty Please save the original shipping cartons as the unit MUST be returned in the original carton and packing Replacement cartons are available at a modest charge If your product needs service please call Outlaw Audio at 866 OUTLAWS 688 5297 You will need to present the original bill of sale to establish the date of purchase In the event that the proof of purchase cannot be established with the original receipt the warranty period shall be determined by the earliest date of manufacture shown on the unit provided that the serial number label has not been altered in any manner or by our records relating to that serial number In the event that you wish to return your Outlaw amplifier back to us for any reason please call to arrange for a Return Authorization Number This will ensure that your problem is discussed with a service technician who will determine if there is a quick solution to your problem Outlaw Audio shall not be liable for or in anyway responsible for inci dental or consequential damages of any kind Some states do not allow limitations on how long an implied warranty lasts and or do not allow the exclusion of incidental or consequential damages Therefore the limita tions and exclusions s
10. eakers Outlaw Audio is not responsible for damage to any speaker system or other component that is caused by using products whose power rating is lower than that of the amplifier Do Not Open The Cabinet There are no user serviceable components inside this product Opening the cabinet may present a shock hazard and any modification to the product will void your guarantee If water or any metal object such as a paper clip coin or a staple accidentally falls inside the unit disconnect it from the AC power source immediately and contact Outlaw Audio for further instructions IMPORTANT SAFETY NOTE Before connecting a new component such as power amplifier to your audio or home the ater system it is always good practice to make certain that all components are turned off and preferably unplugged from their AC power source Many modern electronics products feature automatic turn on circuits that may be activated during an installation causing the potential for damage to electronic components and or speakers Such damage is not covered by product warranties and Outlaw Audio specifically disclaims responsibility for any such damage For Future Reference Record your amplifier s serial number and date of purchase here It is found on the back panel Serial Number Date of Purchase Table of Contents Model 200 M Block Power Amplifier Features Unpacking Front Panel and Rear Panel Installation and Configuration Power Cont
11. ectronic de vice there may be occasional problems upon initial installation or during the life of the unit The items on this list are a brief guide to the minor problems that you may be able to correct yourself If these solutions do not rectify a problem or if the problem persists contact us for assistance Protection Circuitry In the event that the amplifier senses a shorted speaker wire DC voltage on an input connection or thermal overload that could potentially cause damage to the unit or to your speakers it will automatically shut down If this should happen first check all speaker wire connections both at the speakers themselves and at the speaker terminals on the back of the Model 200 Troubleshooting Guide Problem Amplifier will not turn on to make certain that none of the strands from the positive terminal touch those from the negative terminal Even a few stray wire strands can cause the unit to go into the protection mode After checking all speaker connections turn the unit back on If it continues to turn off check your speakers to verify that they are operating properly If all other potential sources of trouble check out properly contact Outlaw Audio for further assistance and information Fuse Replacement The fuse on the Model 200 s rear panel protects the unit s power supply from problems and is not part of the audio circuit If you suspect that a malfunction of the unit is caused by a blown
12. installation or adjustment e Damage caused by connection to AC power outside of the specified range e Damage caused by accident unreasonable use or neglect e Damage from failure to follow instructions contained in this Owner s Manual e Damage from the performance of repairs by someone not authorized by Outlaw Audio e Any unit on which the serial number has been effaced modified or removed e Damage occurring during shipment Consult the carrier for claims due to shipping damage e Units which have been altered or modified in design appearance or construction This warranty covers only the actual defects within the PRODUCT itself IT DOES NOT cover costs of installation in or removal from a fixed installation or normal set up claims based on any misrepresentation by the seller or performance variations resulting from installation related circumstances such as signal quality AC power or incompatibilities with speakers and or other system components During the warranty period Outlaw Audio will at its option either repair the defect or replace the defective product or the defective parts or com ponents thereof at no charge to the owner for parts and labor covered by this warranty If necessary repairs are not covered by this warranty or if aunit is examined which is not in need of repair you will be charged for the repairs and or the examination If non warranted repairs are needed we will notify you of the estimated
13. ject to change without notice or liability to upgrade previously shipped units to current specifications or standards Owner s Manual Outlaw Audio Limited Warranty The Outlaw Audio 30 Day Satisfaction Guarantee This product is guaranteed to satisfy all your needs for a high performance power amplifier If for any reason you are not completely satisfied with it please contact us at 866 OUTLAWS 688 5297 within 30 days of receipt of the unit and you will receive a return authorization Please save all of your packing material in that the amplifier is heavy and can get damaged in shipping without proper protection We recommend that you keep the packing even after 30 days so that if you ever move the unit will be adequately protected If you decide to return the amplifier the only cost you will be responsible for is the shipping charge to return it to us When your amplifier arrives we will inspect it to insure that it was shipped back to us in original condition Upon satisfactory inspection we will issue a full credit for your original purchase price plus your original outbound freight cost at standard ground shipping rate Outlaw Audio Limited Warranty This warranty protects the owner of the Outlaw Model 200 Power Amplifier the PRODUCT for five 5 years from the date of purchase This warranty covers all defects in material and workmanship with the following specific exceptions These are e Damage caused by improper
14. l 200 are turned off To ensure that there will be no unwanted signal transients that can dam age equipment or speakers it is always best to unplug all equipment before making any connections Modern electronic products often have a standby mode that may be activated even though they product may appear to be tuned off Power Control Connections The Model 200 features a built in remote turn on system that will automatically turn on the amplifier in one of two ways Depending on your specific applica tion the unit may also be turned on manually using the Rear Panel AC Power Switch or automatically via sensing of either an input source or a low voltage trigger signal For manual operation no special installation is required For automatic turn on follow the instructions below for the chosen method Remote Turn On From An External Device Using The Low Voltage Trigger To configure the Model 200 so that it turns on automatically in response to a low voltage trigger signal follow these steps 1 Place the Trigger Power Control Mode Switch in the far right position so that the switch is under the words 12 VOLT 2 To trigger the amplifier from a device such as a surround processor AV Receiver or multi room controller with a built in trigger jack connect one end of a cable with a 3 5mm mono mini plug to the Trigger Jack on the Owner s Manual Speaker Wire Connections Model 200 Connect the other end to a matching jack o
15. ms to avoid damage to your processor receiver or controller G Trigger Mode Switch This three position switch determines the method by which the Model 200 will be placed in the active or ON position m When the switch is in the far right position under the word ON the unit will be turned on when the Main Power Switch is turned on When the switch is in the middle position under the word MUSIC the unit will automatically turn on when an audio signal is present at the Input Jacks The unit will automatically turn off when the signal is no longer present When the switch is in the far left position under the 12V indication the unit will automatically turn on when a 6 volt to 35 volt signal is applied to the Trigger Input Jack The unit will turn off shortly after that signal is removed as an Outlaw Audio Processor or Receiver that is capable of providing a Speaker Output Jacks 6 volt to 35 volt control signal at turn on When the Trigger Mode switch is set to the 12 Volt position the Model 200 will turn on when the control signal is present Trigger Output Jack When more than one Model 200 is used in an system this jack may be used to pass the low voltage control signal through to the Trigger Input Outlaw Audio These jacks provide the amplified power signal for connection to your speaker G Input Voltage Switch This switch selects the power AC input voltage for the Model 200 dependi
16. n contact with the jack Be certain to observe proper polarity Finally run the cables to the speaker locations Where possible it is recom mended that the length of cable connecting any pair of speakers is identical even though one speaker may be physically closer to the amplifier than the other Do not coil any excess cable as this may become an inductor that creates frequency response variations in your system NOTE While most speaker manufacturers adhere to an industry conven tion of using black terminals for negative and red ones for positive some manufacturers may vary from this configuration To ensure proper phase connections and optimal performance consult the identification plate on your speaker terminals or the speaker s manual to verify polarity If you do not know the polarity of your speaker ask your dealer or installer of advice before proceeding or consult the speaker s manufacturer As a general rule always avoid running input signal or speaker wire connections in parallel with each other or with AC power cords This can result in undesired hum or other interference that will greatly degrade signal performance Audio Signal Connections Audio connection to the Model 200 is simple and straight forward Connect the output of the source unit which may be the preamp multi room or subwoofer output of a surround processor stereo preamp AV receiver or whole house audio system controller to the Audio Input Jack
17. n cuts off KE Outlaw Audio Amplifier shorted Check speaker connections for short circuit at amp and speaker Owner s Manual A Few Words About Hum and Noise Ground Loop Diagram Coax Cable Cable Feed AN Cables Ground Loop Main House Grounding Set top Box 60Hz AC Ground Loop AC Line AC Line AC Ground A Few Words About Hum and Noise Audible hum or a discernable low frequency noise is one of the most com mon problems in audio video systems This hum which may be present even when the volume is at a low level or when the power is off is usually caused by a problem known as a ground loop A ground loop occurs when there is a difference in ground voltages between two or more components that are connected electrically This in turn creates multiple current paths and causes the low level noise or hum The growing sophistication of home theater systems and the increased number of components used to create these systems has dramatically increased the potential for the possibility of ground loops While it is natural to suspect that the components in your system are the cause of the hum in many cases the cause may be due to other conditions In particular cable TV connections from outside the house have become a major source of hum In most cases one of the following suggestions should help you to solve a hum problem in your system Plea
18. n the unit completely off when it will not be used for an extended period of time This is done by turning the AC Power Switch OFF and noting that the front panel LED indicator goes off This will prevent the automatic turn on circuits from accidentally turning the amplifier on during your absence Note There are no output level controls on the Model 200 as the level is determined by the signal received from your source device We recom mend that after installing a new amplifier such as the Model 200 that you always re calibrate your system to ensure that the system levels match at all speaker locations Model 200 M Block Power Amplifier Ea Owner s Manual Care and Maintenance Care and Maintenance Cleaning When the unit becomes dirty wipe it with a clean soft dry cloth If necessary first wipe the surface with a soft cloth slightly dampened with mild soapy water then with a fresh cloth dampened with clean water Wipe dry immediately with a dry cloth NEVER use benzene thinner alcohol or any other volatile cleaning agent Do not use abrasive cleaners as they may damage the finish of the metal parts Avoid spraying insecticide waxes polishing agents or any aerosol product near the unit Troubleshooting Your Outlaw M Block Amplifier is designed for trouble free operation If you follow the instructions in this manual you should enjoy many years of high quality listening enjoyment However as with any sophisticated el
19. n the device that will be provide a 6 to 35 volt signal when the unit is to be turned on 3 If the source controller does not have a trigger jack you may use the music sense option to automatically turn on the Model 200 however you may also use the trigger switch if the source controller has a switched AC Accessory outlet If that is the configuration you wish to use purchase a small AC to DC power converter as typically used to replace the batteries in portable electronics devices Select a model that is capable of delivering 6 to 35 volts DC and make certain that one of the tips provided with the unit is a 3 5mm mini plug Plug the transformer end of the converter into the switched AC output on the source product and connect the 3 5mm mini plug to the Trigger Jack 4 Press the Power Switch in so that it is engaged and note that the Standby Indicator Q will light for the channel pairs selected for trigger control operation When the source control unit providing the power is turned on the Model 200 will automatically turn on When the source unit is turned off the Model 200 will return to the standby mode Remote Turn On Using Music Sense To configure the Model 200 so that it will automatically turn on when the amplifier is receiving an audio signal follow these steps m Connect the audio input as normal to the Input Jack m Turn the Trigger Mode Switch so that it is in the center position under the word Musi
20. nd the other will have a red line brand name markings a black thread or some other positive indication Follow the proper connection instructions for your system with regard to which terminals are used so that proper system polarity is maintained by connecting the positive usually red terminal on the speaker to the positive terminal on the Model 200 and the negative almost always black terminal on the speaker to the black negative terminal on the Model 200 After the connections are made twist the cap back so that the connection is secured but do not over tighten or use tools as this may break the delicate wire strands and decrease system performance Ifyou are using spade lugs connect them to the wire using the manufacturer s instructions and then loosen the caps on the speaker terminals Place lugs between the plastic cap and the back of the terminal as if it were a horseshoe on the game s post Again remember to observe proper polarity Tighten with your fingers to obtain a positive contact When banana plugs are permitted connections may be made by simply insert ing the jack affixed to your speaker wire into the hole provided on the rear of the colored screw caps on the binding posts Before using banana type jacks make certain that the plastic screw caps are firmly tightened down by turning them in a counter clockwise direction until they are snug against the chassis This will ensure that the maximum surface area of the plug is i
21. ng on the AC power system used in your area IMPORTANT NOTE Do not make any change to this switch setting unless the ac power cord is removed from the unit so that the amplifier is totally disconnected from any ac power source AC Power Switch Turn this switch to the ON position to operate the Model 200 O Fuse This fuse is used to protect the power supply only and is NOT part of the speaker protection circuitry If you suspect that the fuse has blown first disconnect the Model 200 from the AC power source by removing the power cord and then connect the condition that lead to the blown fuse IMPORTANT NOTE The replacement fuse should have the proper rating for the voltage setting in use and must be of the correct type Consult the data printed on the amplifier s rear panel for fuse information If the fuse blows repeatedly discontinue use of the product and contact Outlaw Audio Customer Service for further assistance AC Power Cord Receptacle Connect the AC power cord supplied with the unit to this receptacle and connect the power cord plug to an AC outlet IMPORTANT NOTE A replacement power cord must be equal to the cord supplied with the unit Installation and Configuration SAFETY NOTE When making connections between any source compo nents such as AV Receiver surround processors or multi room controllers and the Model 200 or when making any connections to speakers be certain that both the source device and the Mode
22. ounding of the electrical system in your home may also cause ground loop problems particularly when there are multiple components with three prong grounded power cords Try unplugging these components one at a time and see if one or all of them is causing the problem The ultimate solu tion to this type of problem is to re wire your house with an isolated star type grounding configuration We recognize however that this may be impracti cal and expensive In some cases the use of an approved AC Power Isolation Transformer of sufficient capacity may solve this problem Model 200 M Block Power Amplifier E Owner s Manual Specifications Warning if you suspect that the grounding system in your home s electrical wiring is causing the hum problem it is important that you do not make any changes to the wiring yourself Only a licensed electrician should make any changes to household wiring and they must be made in full compliance with all local building safety and electrical codes Suggestion 4 Faulty earth grounds may also cause hum in your home s electrical system In the past cold water pipes were often used for the earth ground so it is important to make sure that your ground connection is still valid and has not become loose or corroded The cold water pipe method may no longer be valid in some locations due to requirements that the water meter be isolated from the water mains with a length of PVC pipe thus interrupting
23. ower cords under rugs or carpets or place heavy objects on them Damaged power cords should be replaced immediately with cords meeting factory specifications Wiring Cables that are run inside of walls should have the appropriate markings to indicate com plaince with and listing by the UL CSA or other standards required by the UL CSA NEC or your local building Questions about cables inside of walls should be referred to a qualified customer installer or a licensed electrician or low voltage contractor EW Outlaw Audio Installation Location To assure proper operation and to avoid the potential for safety hazards place the unit on a firm and level surface capable of supporting 20 pounds or more When placing the amplifier on a shelf be certain that the shelf and any mounting hardware can support the weight of the amplifier and any additional items in the equipment rack or on the shelf When positioning the amplifier in its final location make certain that it has adequate ventilation on all sides as well as on the top and bottom In particular it is a good idea to provide at least two or three inches of room above the amplifier for air circulation DO NOT place CDs DVDs videotapes owner s manuals or other paper on top of or beneath the unit or in between multiple amplifiers in a stack This will block airflow causing heat build up degraded performance and may create a possible fire hazard If the unit is
24. r the cable Model 200 M Block Power Amplifier 5 Owner s Manual Model 200 Connection Diagram Model 200 Connection Diagram Connect to audio output of the source device Connect to 12V Trigger from Pre Pro or other Connect the speaker wire with care so that proper polarity is maintained Cables with a gauge of 16 may be used for short runs of less than ten feet We do not recommend that you use any cables with an AWG equivalent of 18 or higher due to the power loss and degradation in performance that will occur Cables that are run inside walls should have the appropriate markings in indicate listing with UL CSA or other testing agency standards Questions about cables inside walls should be referred to a qualified installer or a licensed electrical contractor who is familiar with the NEC and or the applicable local building codes in your area If bare wire is used for the connections strip approximately 1 2 inch to 3 4 inch 20mm of insulation from the end of each wire and carefully twist the strands of each conductor together Be careful not to cut the individual strands or twist them off for optimal performance all strands must be used 6 Outlaw Audio Then loosen the knobs of the speaker output terminals far enough so that the pass through hole is revealed Note that one conductor of the speaker cable will have no markings a
25. rns on is determined by the setting for the Trigger Mode Switch B Depending on the setting as described on page 5 the amplifier will turn on in one of these three ways m When the Trigger Mode Switch is set to the left in the On position the Model 200 will turn on when the AC Power Switch is turned on Use the switch to turn the Model 200 off when your finished listening m When the Trigger Mode Switch is set in the center in the Music position the AC Power Switch should be turned ON to place the Model 200 in the Standby Mode The unit will automatically turn on whenever an audio signal is present The unit will return to the Standby mode a few minutes after the audio signal is removed m When the Trigger Mode Switch is set to the right in the 12V position the AC Power Switch should be turned ON to place the Model 200 in the Standby Mode The unit will automatically turn on when a low voltage signal is present at the Trigger Jack and return to the Standby Mode when the host product s trigger signal is removed As a general rule it is always a good idea to turn on your amplifier LAST This avoids the possibility of any turn on pops or transients from other equipment being amplified and sent to your speakers where they may cause damage Always start with a low volume level on your receiver controller or preamp to avoid damage to your speakers SAFETY NOTE 7o prevent unintended operation remember to tur
26. rol Connections Speaker Wire Connections Model 200 Connection Diagram Audio Signal Connections AC Power Connection Operation Care and Maintenance Cleaning Troubleshooting Guide Protection Circuitry Fuse Replacement Outlaw Service Information Troubleshooting A Few Words About Hum and Noise Potential Ground Loops in a Complex A V System O x o 2 0 9 0 6 Os VU ananvwnwn UA WA WwW Ww Specifications The Outlaw Audio 30 Day Satisfaction Guarantee Outlaw Audio Limited Warranty The contents of this manual are Copyright 2003 by Outlaw Audio LLC and may not be duplicated or reproduced by any means whether physical electronic or otherwise without prior written consent from Outlaw Audio Specifications are those in effect at the time of printing Outlaw Audio reserves the right to change specifications or designs at any time without notice or liability to modify or upgrade units previously sold Owner s Manual Unpacking Model 200 M Block Power Amplifier Welcome to the Outlaw Family With your purchase of a Model 200 M Block Amplifier you have become part of a unique worldwide community of audio philes and home theater enthusiasts With one or more Model 200 amplifiers you have the option to add power and flexibility to your system for a wide range of applications such as adding rear surround channels to a new 7 1 system powering passive subwoofers enabling bi amp speaker configurations power ing multi zone multi room
27. se try these steps in the sequence shown proceeding from one step to the next if the prior suggestion does not eliminate the problem Potential Ground Loops in a Complex A V System Suggestion 1 To determine if a cable TV connection is responsible for the hum first turn all components off Disconnect the cable TV feed to your system at the first place where it connects to your components Alternatively disconnect the cable TV wire where it is connected at the wall outlet Turn your system back on and listen if the hum has disappeared If removing the cable TV feed has eliminated the hum you will need to insert a Ground Loop Isolator before reconnecting the cable TV feed or contact your cable TV operator to see if they can better isolate your cable feed Suggestion 2 Turn off all components in your system and then disconnect the input cables at the amplifier Turn the amplifier back on and see if the hum is still present If the hum disappears the fault may be in the input cables used Try replacing them with cables that have better shielding and make certain that the input cables are not running on top of any AC power cords Change the cables one at a time to determine if one or all cables is responsive If the hum disappears when the input cables are disconnected but returns after the cables are changed and the system re connected the problem may be caused by your processor receiver or preamplifier Suggestion 3 Poor gr
28. tated herein may not apply to you This warranty gives you specific legal rights and you may also have other rights which may vary from state to state THERE ARE NO WARRANTIES GIVEN BY OUTLAW AUDIO WHICH EXTEND BEYOND THE DESCRIPTION GIVEN HEREIN ANY IMPLIED WARRANTIES OF FITNESS FOR PURPOSE SOLD MERCHANTIABILITY DESCRIPTION QUALITY OR ANY OTHER MATTERS ARE LIMITED TO THE TERMS OF THE EXPRESSED LIMITED WARRANTY STATED HEREIN Products are sold on the basis of specifications applicable at the time of sales Outlaw Audio shall have no obligation to modify products once they have been sold This warranty is applicable only in the United States For applicability in other countries please call Outlaw Audio This document is Copyright 2003 by Outlaw Audio LLC All Rights Reserved Any unauthorized duplication publication or distribution by any means or in any form whether physical electronic or otherwise is strictly prohibited without prior written consent from Outlaw Audio LLC outlaw Model 200 M Block Power Amplifier
29. torroidal transformer m Removable IEC power cord Unpacking The carton and packing materials used in shipping your new amplifier were specially designed to cushion it from the shocks and vibration of shipping We strongly suggest that you save the carton and packing materials to use if you move or if the unit ever needs to be shipped back to us for any reason To minimize the size of the carton in storage you may wish to flatten it by carefully opening the top and bottom flaps and folding the carton flat Other cardboard inserts may be stored in the same manner Packing materials that cannot be collapsed should be saved along with the carton in a plastic bag Model 200 M Block Power Amplifier 3 Owner s Manual Front and Rear Panel Front Panel and Rear Panel Model 200 M Block Power Amplifier NORTON MASA input 7 12V Trigger Trigger Speaker Outputs in Out Mode WARNING to nepuce He RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE pi 68 Q ne ED AAN CAUTION x A RISK OF ELECTRIC SHOCK NI T SZ NOA DO NOT OPEN sin ZI ee i di S 115V 60Hz 230V 50Hz cat IST sow Q The front panel LED indicator has three modes Amber Indicates that the Model 200 is connected to an AC power source and the rear panel Main Power switch is turned on When the indicator is amber the unitis in the Standby mode and is re
30. w under full load conditions To insure proper performance and to avoid potential safety hazards we recommend that it be connected to a minimum 20 Amp capacity circuit Connecting multiple amplifiers to the same circuit or connecting it to a circuit used by other heavy power devices such as air conditioners may cause circuit breakers to trip NOTE It is always a good idea to avoid using any audio or video equipment on the same AC circuit as equipment with motors such as air conditioners or refrigerators This will lessen the possibility of power variation and electrical start up noise affecting your sound system Extension Cords and Power Strips We do not recommend that extension cords be used with this product unless they are of sufficient gauge to pass the necessary current during full load conditions Most inexpensive extension cords are not capable of such high current loads Similarly should you use a power strip surge protector or any type of AC power line con ditioning equipment make certain that it is also able to handle the high current loads this product will produce Handle the AC Power Cord Gently When disconnecting the power cord from an AC outlet always pull the plug never pull the cord If you do not intend to use the amplifier for any considerable length of time disconnect the plug from the AC outlet If the power cord is replaced make certain that it is of similar gauge As with all electrical devices do not run p
Download Pdf Manuals
Related Search