Oregon SP200 Clock User Manual
Contents
1. To effectively use the pedometer for calculating fat burn and calorie burned based on step count and user body weight and speed and distance walked based on step count and user s height or calibration you are advised to set the time and your user data in the Setting Mode Refer to Setting Mode in this manual NOTE For most accurate measurement please clip the pedometer onto the belt or insert into a tight secure pocket IMPORTANT Remember to set the time and your user data after every battery replacement BATTERY REPLACEMENT The pedometer uses a CR1620 3V battery which has already been installed gt Indicates battery power is low To replace battery 1 Use a small Phillips screwdriver to remove battery compartment lid Once opened please keep the screws in a safe place to avoid losing them 2 Remove the old battery and insert the new one matching the polarities 3 Replace the lid by screwing it back into place using a Phillips screwdriver NOTE When the battery compartment is opened or battery is replaced all data in the pedometer will be reset OPERATION MODES The SP200 has 4 modes of operation Press MODE to navigate between these modes when banner is displayed Clock Pedometer p O D vey 9 km l mI N UEDA Memory Yo Daily Record In the Clock Mode you can e view the time and calendar Clock Date SET Press SET to toggle between displays REMARK Press2. SET Loo Daily Calorie Fat burnt NOTE Unit automatically toggles between screen displays REMARK Press MODE to return to Clock mode TIP Odometer Save e You can input the distance walked after changing battery or performing total reset e Please write down the accumulated distance walked before changing battery or performing total reset function To reset odometer save 1 Press and hold SET to input the values 2 Press MODE to increase values 3 Press SET to confirm and move to next digit NOTE Odometer will be reset to zero after TOTAL RESET or when the battery is replaced RESET THE PEDOMETER After the INITIAL SETTING of the unit there are 2 resetting procedure for user to reset the data e Total reset the pedometer 1 Press MODE to enter the Clock Mode 2 Press and hold both MODE and SET to total reset the pedometer Reset the daily record data Press MODE to enter the Pedometer Mode Press SET to toggle to the Exercise Timer record Press and hold both MODE and SET to reset the daily record wW N a e SETTING MODE Setting Units 1 Press MODE to select measurement unit 2 Press SET to confirm and move to the next setting option The setting sequence is distance time calendar weight Height and calibration NOTE Once measurement unit has been setin the initial setting all other units will automatically follow the same format Measurement Setting option You can set below data af
3. K for calibration press SET to finish Press SET or MODE to proceed step 2 to 6 again 8 Completed the calibration process g e ON o gt NOD SPECIFICATIONS 12 24 format with hour minute 0 99 999 steps Real time clock Step measurement range Distance measurement 6 229006 lancome range Odoemter 9999km or mile Calorie measurement range 0 99 999 Kcal Fat measurement range 0 15 000 g 150cm 249cm or 40 99 50kg 219kg or 66lbs 479lbs 23 hrs 59 mins Body height range Body weight range Exercise timer range Stopwatch measurement 9 hrs 59 mins 59 99 sec capacity Power 1x CR1620 3V battery Operating temperature 10 C to 40 C Storage temperature 20 C to 60 C PRECAUTIONS To ensure you use your product correctly and safely read these warnings and the entire user manual before using the product e Use a soft slightly moistened cloth Do not use abrasive of corrosive cleaning agents as these may cause damage Use lukewarm water and mild soap to clean the device thoroughly after each training session Never use the product in hot water or store it when wet e Do not subject the product to excessive force shock dust temperature changes or humidity Never expose the product to direct sunlight for extended periods Such treatment may result in malfunction e Do not tamer with internal components Doing so will terminate the product warranty and may cause damage The ma
4. MODE to move to Pedometer mode In the Pedometer Mode you can e view the current step count and clock e Exercise timer e Distance walked e Current Speed Press SET to toggle between displays current current step step count count timer Current Distance Speed walked REMARK Press MODE to move to Daily Record mode NOTE The Distance and Exercise timer will be reset automatically to zero at midnight In the Daily Record Mode you can view e Calories burned e Average Speed e Fat burned e Maximum Speed e Current Step count Press SET to toggle between displays Record Mode Calories cbs Fat burned Calories Fat burned SET L ait Current Step count SPD km h Lic t Daily Average Speed Step Daily Max speed SET REMARK Press MODE to move to Memory mode In the Memory Mode you can view the records of your steps distance fat burned calorie burned and timer for the past 7 days and week total accumulated data 1 Press MODE to enter the Memory Mode 2 Press SET to select which day to view week total data and odometer 0000 Days LALLY a et L Days afDays z QP rrr Days LAILA 1 days before data Week Total data Odometer In the day s record the pedometer will automatically toggle between daily step counts exercise timer distance calorie and fat burned Qe rrr rr Days DOAL Daily Step Daily Timer Daily Step Daily Distance
5. OreGco Slimfit 3D Pedometer MODEL SP200 USER MANUAL INTRODUCTION Thank you for selecting the Oregon Scientific Slimfit 3D Pedometer SP200 The PE200 is a 3D sensor type pedometer that can detect steps in any dimension it is carried It is equipped with clock 7 day memory step speed distance fat burn and calorie counter functions IMPORTANT Do not immerse the pedometer in water CONTROL BUTTONS MODE SET 1 MODE Toggle between main modes increase values 2 SET Toggle between sub modes confirm and move to next setting option Pedometer Mode Indicates total data within a week Displays Time number of step or step walked Battery Display Indicates step counter is On Indicates on which day 1 7 before is displayed data recorded Displays indicates current speed or calorie reading or distance walked Time Max Average speed exerise Time 8 Unit grams calorie 9 Indicates alarm is On 10 Distance Unit Miles Kilometres per hour 11 Indicates calorie mode 12 Indicates speed Soro SN GETTING STARTED e Carrying the pedometer The SP200 can be carried on the waist around the neck or in pockets and handbags by using detachable clip provided pull to slide off the Hook pedometer Wearing Clip AY A AS ey tj y nt a r Te im i i i Ki n vi te H vA ij a 3 M 1 a i lt i i lt ti Ar S hy i i f i e Set time and user data
6. artment directly please visit https us oregonscientific com service support asp For international inquiries please visit https us oregonscientific com about international asp EU DECLARATION OF CONFORMITY Hereby Oregon Scientific declares that this Slimfit 3D pedometer Model SP200 is in compliance with EMC directive 2004 108 EC A copy of the signed and dated Declaration of Conformity is available on request via our Oregon Scientific Customer Service 5 gy A RoHS COMPLIANT
7. in unit contains no user serviceable parts e Donot scratch hard objects against the LCD display as this may cause damage e Take precautions when handling all battery types e Remove the batteries whenever you are planning to store the product for a long period of time e When replacing batteries use new batteries as specified in this user manual e The product is a precision instrument Never attempt to take this device apart Contact the retailer or our customer service department if the product requires servicing e Do not touch the exposed electronic circuitry as there is a danger of electric shock e Check all major functions if the device has not been used for a long time Maintain regular internal testing and cleaning of your device Have your device serviced by an approved service centre annually e When disposing of this product ensure it is collected separately for special treatment and not as normal household waste e Due to printing limitations the displays shown in this manual may differ from the actual display e The contents of this manual may not be reproduced without the permission of the manufacturer NOTE The technical specifications for this product and the contents of the user manual are subject to change without notice ABOUT OREGON SCIENTIFIC Visit our website www oregonscientific com to learn more about Oregon Scientific products If you re in the US and would like to contact our Customer Care dep
8. ter initial setting e Clock and calendar e Height e Weight e Calibration Clock and Calendar setting Press MODE to enter the Clock Mode Press and hold SET to set values Press MODE to increase values Press SET to confirm and move to the next setting option a eS The setting sequence is 12 24 time format time hour minute and second calendar year month and date Weight Height and calibration setting Press MODE to enter the Pedometer Mode Press and hold SET to set values Press MODE to increase values Press SET to confirm and move to the next setting option a i ea The setting sequence is weight Height and Calibration Run Walk Calibration in RUN or WALK setting ER eR v SET Q on RL co WNE 1 Press MODE to enter the Pedometer Mode 2 Press and Hold SET to set values 3 Press MODE to select YES or NO for Calibration To select NO for calibration It will be returned to Pedometer Mode ACEP E NOTE The pedometer will be calibrated automatically based on user s height if user select NO for calibration To select YES for calibration Press MODE to select YES the pedometer Press MODE to select RUN or WALK Press SET to confirm and moving to the next setting option Press MODE to increase values for distance setting Press SET to confirm and press once more to start calibration or press MODE to move back to the Calibration setting mode After RUN or WAL
Download Pdf Manuals
Related Search