Nortel Networks P0886634 Answering Machine User Manual
Contents
1. P0886634 Issue 1 0 FAX Installation Guide 6 Installing the DFC on systems equipped with DVCs Installation overview To add Norstar Voice Mail FAX to a system equipped with DVCs you must Set the DFC jumpers e Install the DFC e Connect the DFC to the DVCs with the PEB cable e Enable the FAX software Shutting down the Norstar Voice Mail system Before you remove the power from Norstar Voice Mail you must shutdown the Norstar Voice Mail system Performing a shutdown allows Norstar Voice Mail to perform all necessary shutdown activities before the power is removed A shutdown prevents data from being lost Note A shutdown must be done from a Norstar telephone with a two line display To shutdown the Norstar Voice Mail system 1 Press Feature 9 1 5 J Password 2 Enter the default password 2 2 2 3 7 7 2 x ACCESS and press OE ACCESS Server 3 Press HEST BACE HEST ADMIN J System shutdowr 4 Press SHOW EACK HEST SHOW Shutdown ture 5 Press HEXT until the display shows QUIT HEST GRACE Shutdown ture 6 Press QUICK then YES to continue with the QUIT HEXT BUICK n shutdown The Norstar Voice Mail system shuts down in 15 seconds For more information about shutdown procedures refer to the Norstar Applications Module Installation and Maintenance Manual FA X Installation Guide P0886634 Issue 1 0 I2. 11 Replace the front cover 12 Plug the power cord into the AC outlet P0886634 Issue 1 0 FA X Installation Guide 22 Installing the DFC on systems equipped with a BIC Re installing the BIC in the NAM Before you begin to install the BIC ensure you use an antistatic strap to ground yourself To re install the BIC 1 Ground yourself by attaching one end of the grounding strap to your wrist and the other end to a grounded metal surface 2 Locate expansion slot 2 fora NAM II and slot 4 for anew NAM 3 Gently push the large ribbon cables leading to the SBC flat against the backplane This allows for easier installation of the BIC 4 Carefully hold the BIC along the top Insert the card by aligning it between the metal groove on one side and the slot opening on the other side Figure 16 Re installing the BIC ina NAM Il SS FA X Installation Guide P0886634 Issue 1 0 Installing the DFC on systems equipped with a BIC 23 Figure 17 Re installing the BIC in a new NAM 5 Push the BIC straight back until it fits snugly in place Ensure the edge connector is firmly inserted into the socket 6 If you have a NAM II reconnect the Serial Port A and Serial Port B connectors to the SBC Reconnect the keyboard mouse connector to the SBC For the loca
3. An external caller can request a fax to be sent to them from a Fax on demand Mailbox e Fax Overflow When the office fax machine is unavailable for use faxes can be temporarily stored in a fax Overflow Mailbox and printed later e Fax System Group Message Fax Broadcast A Fax System Group Message can be sent whenever you want to notify a special group by way of a fax of a pending event or company notice To print fax documents from a Fax Overflow Mailbox the fax machine must be connected to the same Norstar system as the NAM To print a fax document from a Personal Mailbox the fax machine does not need to be connected to a Norstar system A fax machine may also be required for loading fax documents in a Fax on demand Mailbox P0886634 Issue 1 0 FA X Installation G uide 2 Introduction to Norstar Voice Mail FAX Figure 1 FAX overview External fax machine External caller receives a fax from Fax on Demand Mailbox OR Fax sent to office fax machine behind Norstar or to a Personal Mailbox Personal Mailbox Other office receives a fax as part of a message Norstar Mailboxes are accessed and fax programming is done from here Fax Overflow Mailbox stores faxes if office fax machine is busy and prints them later Norstar Telephone Norstar Voice Mail Fax on demand Mailbox sends out a fax at the request of an exter
4. NORTEL NORSTAR Norstar Voice Mail 4 0 FAX Installation Guide A i Contents Chapter 1 Chapter 2 Chapter 3 Regulatory information iii Repair facilities iv Introduction to Norstar Voice Mail FAX 1 FAX overview 1 DEC overview 3 Specifications 3 Special tools 3 Precautions 4 Enabling the FAX software 4 Installing the DFC on systems equipped with DVCs 5 Installation overview 6 Shutting down the Norstar Voice Mail system 6 Opening the NAM 7 Installing the DFC in the NAM 8 Installing the PEB Cable 11 Enabling the FAX software 13 Adding a Digital Voice Card after FAX is installed 14 Installing the DFC on systems equipped with a BIC 17 Installation overview 18 Removing the BIC 18 Installing the Media Services Bus Expansion Card BEC on the BIC 19 Re installing the BIC inthe NAM 22 Installing the DFC in the NAM 24 Connecting the DFC to the BIC with the PEB Cable 24 Enabling the FAX software 27 P0886634 Issue 1 0 FA X Installation Guide FA X Installation Guide P0886634 Issue 1 0 Regulatory information ili Regulatory information FCC Regulations This equipment complies with Part 68 Rules and Regulations of the FCC Regulations for direct connection to the public switched telephone network DOC Regulations This equipment complies with CS 03 Rules and Regulations of the Canadian DOC Regulations for direct connection to the public switched telephone network Radio fr
5. Tel 615 883 9220 Tel 416 744 5201 Fax 416 744 5227 Note You receive an RA when you call the repair center in Nashville This number should appear on the package of any and all parts sent to this location for repair FA X Installation Guide P0886634 Issue 1 0 Introduction to Norstar Voice Mail FAX 1 Norstar Voice Mail FAX provides Norstar Voice Mail with fax functionality This installation guide is intended for the installer of Norstar Voice Mail FAX and describes how the FAX option should be installed and prepared for operation Norstar Voice Mail FAX can be installed on systems equipped with either a Media Services Base Interface Card BIC or Digital Voice Cards DVC s The procedures for installing the Digital Fax Card DFC differs between the systems Follow the instruction on which system you have installed The installer is responsible for e installing the DFC e connecting the DFC to the DVCs or BIC e enabling the FAX software FAX overview The Norstar Voice Mail FAX software is factory installed on the Norstar Applications Module NAM The FAX software must be enabled after the DFC is installed The FAX option provides Norstar Voice Mail with the following features e Fax Mail Faxes received from external fax machines are stored in personal mailboxes e Fax Answering Faxes received from external fax machines are automatically sent to a predefined fax extension e Fax on demand
6. to the following table Position 2 1 State on on 5 Ensure there is a jumper on position 10 of the INTERRUPT Note The settings in these table are the default values and should be set properly when the board is received Refer to Figure 2 on page 5 for the location of the switch SW1 SW2 and the INTERRUPT jumpers 6 Carefully hold the DFC along the top only Insert the card by aligning between the metal groove on one side and the slot opening on the other side 7 Push the DFC straight in until it is snugly in place Ensure the edge connector is firmly inserted into the socket 8 Fasten the slot cover screw in the DFC slot cover Note If there is a DVC in slot 6 of the NAM you must connect the PEB cable to the DFC before installation If there is a DVC in slot 7 of the NAM II you must connect the PEB cable to the DFC before installation FAX Installation Guide P0886634 Issue 1 0 Installing the DFC on systems equipped with DVCs 11 Installing the PEB Cable Figure 7 shows an example of how the PEB cable is installed on an earlier NAM In this example the Norstar Voice Mail module is equipped with four DVCs The DFC is at the right end of the PEB chain in slot 7 and the leftmost DVC DVC 1 is at the other end of the chain in slot 3 Figure 7 NAM PEB Cable installation example DF P DVC2 e Slot 7 DVCI Slot 4 Slot 5 Slot 3 Figure 8 shows an example
7. EB socket on the DFC The PEB cable is keyed and can only be installed one way You must also ensure the Pin 1 indicator colored stripe is on the edge furthest away from the top of the NAM FAX Installation Guide P0886634 Issue 1 0 Installing the DFC on systems equipped with DVCs 13 Figure 11 Installing the PEB Cable PEB Connector DFC Interrupt SW 2 SW1 TULL Em BERGE PEB Terminator 5 Insert the DVCs and connect the PEB cable to each card Note To ease installation start with the DVC that is closest to the DFC and finish with the DVC farthest away Also make sure you connect the PEB cable before you insert the next DVC 6 Fold the PEB cable so it lies flat against the card edges 7 Proceed to step 1 of Enabling the FAX software Enabling the FAX software The FAX option must be enabled after installing the DFC After FAX capability has been added to Norstar Voice Mail you can add or customize Fax Overflow and Fax on demand information For more information about customizing the FAX software refer to the Norstar Voice Mail FAX Set Up and Operation Guide 1 Insert the FKENABLE diskette into the floppy disk drive 2 Plug in the module and wait for the NAM to boot from the disk This takes approximately three minutes 3 After all disk activity has ceased
8. Norstar Applications Module Installation and Maintenance Manual is included on the Norstar Voice Mail 4 0 Documentation and Client Software CD ROM All the Norstar Voice Mail Installation Manuals on the CD ROM are protected by the password Norstar99 CAUTION A You must wear an antistatic grounding strap at all times when handling electronic components Failure to do so may result in damage to the equipment P0886634 Issue 1 0 FA X Installation Guide 4 Introduction to Norstar Voice Mail FAX Precautions Before installing or upgrading a DFC you must take the following precautions e Shut down the Norstar Voice Mail system A shutdown procedure allows Norstar Voice Mail to perform all necessary shutdown activities before power n is removed For more information refer to Shutting down the Norstar Voice Mail system on page 6 e Unplug the NAM power cord The NAM power supply contains high voltage If you do not unplug the power cord you may severely injure yourself Also if cards are installed or removed from the NAM before the power cord is unplugged the cards and or the NAM may be damaged e Wear an antistatic ground strap Static electricity can damage the components on the cards and the NAM Always wear a properly grounded antistatic strap while handling the DFC DVC BIC or any other Norstar Voice Mail component Ground yourself by attaching one end of the grounding strap to your wrist and the other end to a grou
9. Type A is a daughterboard that is installed on the BIC provides the BIC with the ability to connect to a Digital Fax Card DFC Before you begin the installation you must have 2 Phillips screwdriver To install the BEC 1 Ground yourself by attaching one end of the grounding strap to your wrist and the other end to a grounded metal surface P0886634 Issue 1 0 FA X Installation Guide 20 Installing the DFC on systems equipped with a BIC 2 Place the BIC on a flat surface with the components facing up Refer to Figure 15 on page 21 Caution A Failure to place the BIC on a flat surface may result in serious damage to the BIC W hile the BIC is out of the NAM be careful not to slide or catch the back of the BIC this may cause damage to the pins on the back of the board 3 Unpack the small plastic bag from the shipping container Make sure you have two screws and two jumpers 4 Locate JP1 and JP2 on the BEC JP1 and JP2 are located next to the PEB connector 5 Remove the two jumpers from the small plastic bag Install the two jumpers in an open position on the bottom pin of JP1 and JP2 For the jumper to be in the open position the outside half of each jumper must not cover a pin Refer to Figure 14 for the jumper positions Figure 14 BEC jumper position 6 Unpack the BEC daughterboard from the shipping container and antistatic bag The BIC is equipped with two posts at the bottom of the board for co
10. and the light on the floppy disk drive has gone out unplug the NAM and remove the FXENABLE diskette from the floppy disk drive The FAX software is now enabled 4 Replace the front cover Insert the tongues on the bottom of the front cover into the module slots 5 Fasten the two screws holding the front cover to the module P0886634 Issue 1 0 FA X Installation G uide 14 Installing the DFC on systems equipped with DVCs 6 T Close the module door Note To lock the door turn the lock 90 clockwise until the screwdriver slot is horizontal Plug the power cord into the AC outlet Adding a Digital Voice Card after FAX is installed After you have installed the FAX option on the NAM the installation of another DVC requires a few extra steps These extra steps are required to remove PEB terminators and install the PEB cable To install a DVC l Warn customers that Norstar Voice Mail will be out of service while you are installing the expansion card Shutdown the NAM For more information refer to Shutting down the Norstar Voice Mail system on page 6 Remove the NAM power cord from the AC outlet Ground yourself by attaching one end of the grounding strap to your wrist and the other end to a grounded metal surface Open the NAM door and remove the front cover Refer to Opening the NAM on page 7 Set the switches and jumpers on the DVC you are adding Settings for the switches and jumpers are listed i
11. ar Voice Mail system For more information refer to m Shutting down the Norstar Voice Mail system on page 6 Remove the NAM power cord from the AC outlet Ground yourself by attaching one end of the grounding strap to your wrist and the other end to a grounded metal surface Remove the front cover Refer to Opening the NAM on page 7 If you have a NAM II disconnect the Serial Port A and Serial Port B connectors from the SBC Disconnect the keyboard mouse connector from the SBC Refer to Figure 13 on page 19 The NAM II has 8 expansion slots If you have a new NAM proceed to step 6 The new NAM has 6 expansion slots FAX Installation Guide P0886634 Issue 1 0 Installing tne DFC on systems equipped with a BIC 19 Figure 13 Disconnecting the Serial Ports A and B and the keyboard mouse connector Keyboard mouse backplane connector Serial Port A Connector Serial Port B Connector Keyboard mouse Connector 6 Locate the BIC and disconnect the fiber cable The BIC is located in Slot 2 of the NAM II and in Slot 4 of the new NAM 7 Remove the slot cover screw 8 Use both hands to carefully hold the BIC along the top Lift the BIC straight up and out from the module Sometimes the BIC is tightly seated and difficult to remove You may need to wiggle it out with a slight rocking motion Installing the Media Services Bus Expansion Card BEC on the BIC A Media Services Bus Expansion Card BEC
12. edge connector is firmly inserted into the socket 8 Fasten the slot cover screw in the DEC slot cover Connecting the DFC to the BIC with the PEB Cable There are no fiber connections to the DFC The DFC uses the voice ports on the BIC to connect the fax ports to fax machines or a call Only one DFC can be installed in a NAM The DFC connects to the BEC daughterboard attached to the BIC through the PCM Expansion Bus PEB cable This cable must be connected from the DFC to the BIC The PEB cable connects the DFC to the BIC to share the ports connected to the Norstar KSU FA X Installation Guide P0886634 Issue 1 0 Installing the DFC on systems equipped with a BIC 25 Note The BIC must have a BEC daughterboard installed before it can be connected to the DFC For instructions on installing the BEC daughterboard refer to Installing the Media Services Bus Expansion Card BEC on the BIC on page 19 Figure 18 shows an example of how the PEB cable is installed on a NAM II The DFC is at the right end of the PEB chain in slot 8 and the BIC is at the other end of the chain in slot 2 The three extra connectors on the PEB cable remain empty Figure 19 on page 26 shows how the PEB cable is installed on a new NAM The DFC is in slot 1 and the BIC is at the other end of the chain in slot 4 The three extra connectors on the PEB cable remain empty You must use the PEB cable provided in the BEC shipping container The PEB cable is p
13. equency interference Warning This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communications It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of the FCC Rules and CSA specification C108 8 which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case users will be required at their own expense to take whatever measures necessary to correct the interference This apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations for the Canadian Department of Communications CAUTION A The Norstar Applications M odule contains fragile electronic parts DO NOT DROP OR BUMP THE MODULE P08866 34 Issue 1 0 FA X Installation Guide iv Repair facilities Repair facilities In the event of equipment malfunction all repairs must be performed by Northern Telecom or by one of its authorized dealers In the USA In Canada Northern Telecom Inc Nashville Repair and Distribution Center 640 Massman Drive Nashville TN 37210 Northern Telecom Canada Ltd 30 Norelco Drive W eston ON M9L2X6 Attn RA
14. le must be connected from the DFC to the BIC The PEB cable connects the DFC to the BIC to share the ports connected to the Norstar KSU The following section provides step by step instructions for the installation of the FAX software a DFC a BEC and the PEB cable in a Norstar Voice Mail system that is equipped with a BIC For information on installing a DFC in a Norstar Voice Mail system equipped with a Digital Voice Card DVC refer to Installing the DFC on systems equipped with DVCs on page 5 Figure 12 Digital Fax Card PEB Connector Interrupt SW 2 SW1 be PEB Terminator SIIT TMT fas P0886634 Issue 1 0 FA X Installation Guide 18 Installing the DFC on systems equipped with a BIC Installation overview To add Norstar Voice Mail FAX to a system equipped with a BIC you must Remove the BIC from the NAM Install the Media Services Bus Expansion Card BEC Type A on to the BIC Re install the BIC in the NAM Set the BEC jumpers Install the DFC Connect the DFC to the BIC with the PEB cable Enable the FAX software Removing the BIC The BIC is removed when a Media Services Bus Expansion Card BEC is being added to the BIC The BEC is installed along with the DFC to provide the NAM Norstar Voice Mail FAX capability To remove the BIC 1 Shutdown the Norst
15. mprovements Thank you We appreciate your time and consideration Nortel Product Training and Documentation Return mail address Documentation User Comments Survey Nortel Product Training and Documentation P O Box 833858 M S H300 Richardson TX 75083 3858 USA FAX Installation Guide P0886634 Issue 1 0 30 Fax to Documentation User Comments Survey Nortel Product Training and Documentation 1 972 684 8699 Please circle the most appropriate number on the scale for each question 1 Overall are you satisfied with this document Yes 7 6 5 4 3 2 1 No 2 Is it easy to find information in this document Yes 7 6 5 4 3 2 1 No 3 Have you found the information in this document to be technically accurate Yes 7 6 5 4 3 2 1 No 4 Is this document clearly written Yes 7 6 5 4 3 2 1 No 5 Is the information in this document complete for its purpose Yes 7 6 5 4 3 2 1 No 6 Does this document help you do your job Yes 7 6 5 4 3 2 1 No Comments Optional Your name Fax Company FAX Installation Guide P0886634 Issue 1 0 1 800 4 NORTEL www nortel com norstar Norstar is a trademark of Northern Telecom P0886634 Issue 1 0 Printed in Canada
16. n the Norstar Applications Module II Installation and Maintenance Manual Remove the XRN1 and XRN2 terminators from the DVC you are installing Note Keep the PEB terminators in a safe place If the DFC is removed the terminator plugs must be re installed on the DVCs Disconnect the PEB cable from the DVCs already installed in the NAM Remove the slot cover screw and the metal slot cover from the slot you are adding the new DVC to DVC slot assignment is listed in the Norstar Applications Module II Installation and Maintenance Manual 10 Insert the new DVC into the appropriate slot 11 Connect the PEB cable to each DVC in the NAM FAX Installation Guide P0886634 Issue 1 0 Installing the DFC on systems equipped with DVCs 15 12 Fold the PEB cable so it lies flat against the card edges 13 Replace the front cover and close the module door 14 Plug the power cord into the AC outlet For a detailed description about installing a DVC refer to the Norstar Applications Module II Installation and Maintenance Manual P08866 34 Issue 1 0 FAX Installation Guide 16 Installing the DFC on systems equipped with DVCs FAX Installation Guide P0886634 Issue 1 0 Installing the DFC on systems equipped with 3 a BIC Only one DFC can be installed in the NAM The DFC connects to the Media Services Bus Expansion Card BEC daughterboard attached to the Media Services Base Interface Card BIC through the PCM Expansion Bus PEB cable This cab
17. nal caller Fax on demand faxes can be fed into office fax machine and are then sent to the desired Office fax machine Fax on demand Mailbox FA X Installation Guide P0886634 Issue 1 0 Introduction to Norstar Voice Mail FAX 3 DFC overview The Digital Fax Card DFC is installed in an expansion bus slot on the Norstar Application Module NAM and supports four Fax Channels There are no Time Compression Multiplexing TCM connections to the DFC The DFC uses the Voice Channels on the Digital Voice Cards DVCs or BIC to connect the Fax Channels to fax machines or a call Note When Norstar Voice Mail FAX is using a Voice Channel to connect to the fax machine or a caller that Voice Channel cannot be used by other users until the FAX function is complete Specifications The DFC is an AT bus compatible card that provides e 9600 baud with auto step down to 7200 4800 and 2400 bps e DTMF generate and detect e error correction mode e fine and normal image resolution e V 21 V 27 V 29 T 4 MH amp MR T 6 MMR T 30 protocols e four Group III analog Fax Channels Special tools Before you begin replacing or upgrading the components ensure you have the following equipment e 2 Phillips head screwdriver with a 3 5 in long blade e 3 16 in slot screwdriver e an antistatic grounding strap e 3 16 in nut driver recommended You may also need the Norstar Applications Module Installation and Maintenance Manual The
18. nded metal surface Enabling the FAX software The FAX option must be enabled after installing the DFC Refer to Enabling the FAX software on page 13 or Enabling the FAX software on page 27 for instructions on how to enable the FAX option After FAX capability is added to Norstar Voice Mail you can add or customize Fax Overflow and Fax on demand information For more information about customizing the FAX software refer to the Norstar Voice Mail FAX Set Up and Operation Guide FA X Installation Guide P0886634 Issue 1 0 Installing the DFC on systems equipped with 2 DVCs Only one DFC can be installed in the Norstar Applications Module NAM The DFC connects to the DVCs through the PCM Expansion Bus PEB cable This cable must be connected from the DFC to each DVC The PEB cable connects the DFC to the DVC to share the ports connected to Norstar The following section provides step by step instructions for the installation of the FAX software a DFC and the PEB cable in a Norstar Voice Mail system equipped with Digital Voice Cards DVC s For information on installing a DFC in a Norstar Voice Mail system equipped with a Media Services Base Interface Card BIC refer to Installing the DFC on systems equipped with a BIC on page 17 Figure 2 Digital Fax Card and PEB cable PEB Connector PEB Terminator rumnn o UU CEE Eea J
19. nnection of the BEC daughterboard Handle the BEC daughterboard by its edges at all times Do not touch any card components Make sure you have the two screws that came with the BEC daughterboard FA X Installation Guide P0886634 Issue 1 0 Installing the DFC on systems equipped with a BIC 21 Figure 15 BIC connection points Fiber connectors Female BEC daughterboard connection points _Q ROMINA LR ansa Connection post screw hole posts PEC Slots 4 7 Lightly press the BEC daughterboard down onto the female BEC daughterboard connectors on the BIC The BIC connection screw hole posts should be flush with the BEC daughterboard screw holes For the location of the BIC and BEC daughterboard connection points refer to Figure 15 8 Before pressing the BEC daughterboard completely down ensure the male BEC daughterboard connectors line up with the female BEC daughterboard connection points on the BIC 9 Fasten the BEC daughterboard to the BIC connection screw hole posts using the two screws provided For the location of the BIC and BEC daughterboard connection points refer to Figure 15 10 Insert the BIC back into the NAM Refer to Re installing the BIC in the NAM on page 22
20. nstalling the DFC on systems equipped with DVCs 7 Opening the NAM 1 Warn customers that Norstar Voice Mail will be out of service while you are installing the FAX option 2 Shutdown the Norstar Voice Mail system Note For information about performing a shutdown refer to Shutting down the Norstar Voice Mail system on page 6 3 Unplug the NAM power cord from the AC outlet 4 Ground yourself by attaching one end of the grounding strap to your wrist and the other end to a grounded metal surface 5 Open the module door The door may be locked To unlock the door use a screwdriver to turn the lock in the bottom right corner of the door Turn the lock 90 counterclockwise until the screwdriver slot is vertical Figure 3 Unlocking the module door 6 Remove the two screws holding the front cover to the module The screws are located along the top of the front cover 7 Slide the front cover up and out from the module P0886634 Issue 1 0 FA X Installation Guide 8 Installing the DFC on systems equipped with DVCs Figure 4 Removing the front cover TTT Dt I aM M Min LLC Installing the DFC in the NAM 1 Make sure you are wearing your antistatic grounding strap Ground yourself by attaching one end of the grounding strap to your wrist and the other end to a grounded metal surface 2 Ifyou are installing FAX on an earlier NAM locate slot 7 on the expansion bus Rem
21. of how the PEB cable is installed on a NAM IL In the example the module is equipped with four DVCs The DFC is at the right end of the PEB chain in slot 8 and the leftmost DVC DVC 1 is at the other end of the chain in slot 2 Figure 8 NAM II PEB Cable installation example z po pvc4 DFC Slot 7 Slot 8 DVC 2 SBC Slot 5 DVC 3 DVC 1 Slot 4 Slot 6 Slot 2 To install the PEB cable P0886634 Issue 1 0 FAX Installation Guide 12 Installing the DFC on systems equipped with DVCs 1 Remove all DVCs from the NAM 2 Remove the PEB terminator XRN2 from DVC 1 Refer to Figure 9 for the location of the PEB terminators Figure 9 Digital Voice Card PEB connector PEB terminator XRN1 PEB terminator XRN 2 To remove a PEB terminator place a flat head screwdriver between the terminator and its socket and gently pry the terminator loose Figure 10 Removing a PEB terminator is DID 3 Remove both PEB terminators XRN1 and XRN2 from any remaining DVCs Note Keep the PEB terminators in a safe place If the DFC is removed the terminator plugs must be re installed on the DVCs 4 Connect one end of the PEB cable to the P
22. ove the slot cover screw and the metal slot cover from the slot Refer to Figure 5 on page 9 If you are installing FAX on a NAM II locate slot 8 on the expansion bus Remove the slot cover screw and the metal slot cover from the slot Refer to Figure 6 on page 9 Keep the metal slot cover and screw You must re install the metal slot cover if you remove the DFC FAX Installation Guide P0886634 Issue 1 0 Installing the DFC on systems equipped with DVCs 9 Figure 5 Locating the expansion bus slots on a NAM WAM TI LIDI 2777 DFC Slot 8 P0886634 Issue 1 0 FA X Installation Guide 10 Installing the DFC on systems equipped with DVCs 3 Switch SWI should be set according to the following table Position 8 7 6 5 4 3 2 1 State off on off off on on on on 4 Switch SW2 should be set according
23. re folded for correct installation WARNING The microprocessor heat sink may be hot Pay careful attention not to touch the heat sink when installing the PEB cable Figure 18 Connecting the BIC to the DFC in a NAM Il DFC connector Emp cable connectors BIC connector located on the BEC daughterboard P0886634 Issue 1 0 FA X Installation Guide 26 Installing the DFC on systems equipped with a BIC Figure 19 Connecting the BIC to the DFC DFC connector PEB Cable DFC in slot 1 BIC connector located on the BEC daughterboard BIC in slot 4 To connect the BIC to the DFC with the PEB cable WARNING A The microprocessor heat sink may be hot Pay careful attention not to touch the heat sink when installing the PEB cable 1 Connect one end of the PEB cable to the PEB socket on the DFC The PEB cable is keyed and can only be installed one way You must also ensure the Pin 1 indicator colored stripe is on the edge furthest away from the top of the module 2 Connect the last connector on the PEB cable to the BIC The remaining connectors on the PEB cable can remain empty and can be folded and gently pushed flat against the backplane 3 Proceed to step 1 of Enabling the FAX software FA X Installation Guide P0886634 Issue 1 0 Installing the DFC on sy
24. stems equipped with a BIC 27 Enabling the FAX software The FAX option must be enabled after installing the DFC After FAX capability has been added to Norstar Voice Mail you can add or customize Fax Overflow and Fax on demand information For more information about customizing the FAX software refer to the Norstar Voice Mail FAX Set Up and Operation Guide 1 2 Insert the FXENABLE diskette into the floppy disk drive Plug the power cord into the AC outlet and wait for the NAM to boot from the disk This takes two to three minutes When all disk activity has ceased and the light on the floppy disk drive goes out unplug the NAM and remove the FXENABLE diskette from the floppy disk drive Replace the front cover Insert the tongues on the bottom of the front cover into the module slots Fasten the two screws holding the front cover to the module Close the module door To lock the door turn the lock 90 clockwise until the screwdriver slot is horizontal Plug the power cord into the AC outlet P0886634 Issue 1 0 FA X Installation G uide 28 Installing the DFC on systems equipped with a BIC FA X Installation Guide P0886634 Issue 1 0 29 Tell us what you think This is your document Nortel wants it to work well for you Please take a few minutes to answer the questions on the other side of this page Fax it back to us at the number provided or mail it to the address below Your comments will be used to make i
25. tion of the connectors refer to Figure 13 on page 19 Note Ensure the keyboard mouse ribbon cable is still connected to the backplane 7 Fasten the slot cover screw in the BIC slot cover 8 Replace the front cover P0886634 Issue 1 0 FA X Installation Guide 24 Installing the DFC on systems equipped with a BIC Installing the DFC in the NAM 1 Ground yourself by attaching one end of the grounding strap to your wrist and the other end to a grounded metal surface 2 If you have a NAM II locate slot 8 on the expansion bus If you have a new NAM locate slot 1 on the expansion bus Remove the slot cover screw and the metal slot cover from the slot Keep the metal slot cover and screw You will have to re install the metal slot cover if you remove the DFC 3 Switch SWI should be set according to the following table a E O n I I 4 Switch SW2 should be set according to the following table Position 2 1 State on on 5 Ensure there is a jumper on position 10 of the INTERRUPT Note The settings in these table are the default values and should be set properly when the board is received Refer to Figure 12 on page 17 for the location of the switch SW1 SW2 and the INTERRUPT jumpers 6 Carefully hold the DFC along the top only Insert the card by aligning between the metal groove on one side and the slot opening on the other side 7 Push the DFC straight in until it is snugly in place Ensure the
Download Pdf Manuals
Related Search