Nikon AX-110 Scanner User Manual
Contents
1. Cautions Y e When positioning a document that has staples or clips attached ensure that they do not scratch the surface of the document setting glass e Make sure that the glass is free of dust or dirt as this may affect the quality of the scanned images e When positioning a document make sure you do not touch the glass as this may affect the quality of the scanned images Step 3 Close the document cover gently 28 Nikon ScanTouch 110 User s Manual 6 Maintenance 6 Maintenance With the exception of periodic cleaning or lamp replacement the scanner is virtually maintenance free The following sections give the procedures for basic maintenance of the scanner 6 1 Static Electricity Precautions Static electricity is a constant danger to computer systems The charge that can build up in your body may be strong enough to damage electronic components on the scanner s printed circuit board or the computer s interface card Therefore it is important to observe basic precautions whenever handling electronic components for your computer Although areas with high humidity are much less prone to static electricity it is best to always take precautions against accidental damage that can result in expensive repairs The following measures should generally be enough to protect your equipment from static discharge Discharge any static electricity that may have built up in your body by touching a grounded or antistat2. If the IDs are duplicated you must change the ID number of the other SCSI device or of the ScanTouch 110 to avoid any conflict Remarks rv e To change the ID confirm that the scanner power is off The ID cannot be changed when the power is on e Do not use SCSI ID 8 and 9 or A through F on your scanner They are for factory use only e As 7 has been assigned for the CPU and 0 has been assigned to the built in hard disk for a Macintosh and 0 and 7 have also been assigned to other personal computer systems any number from to 6 is recommended for the ID number e If conflicting ID numbers are assigned your system might not function or important data on the hard disk might be destroyed It is therefore essential to check the ID numbers carefully before connecting the scanner Nikon ScanTouch 110 User s Manual 23 5 Operation 5 Operation 5 1 Turning on the Power Before turning the power on confirm that the carriage lock is in the unlocked position amp u A Turn the scanner on first the other SCSI devices next and the host computer last U Ko PA A 100 24 O Oo Power OFF Power ON The scanner automatically performs a simple self test each time it is turned on to help spot major system errors in the scanner itself Once the scanner has been unpacked and the shipping restraint has been removed the scanner is ready to perform this test 24 Nikon ScanTouch 110 User
3. 50 pin connector BA Terminator Nikon ScanTouch 110 User s Manual 4 Connecting the Scanner SCSI Chain Connection with Other Devices If your ScanTouch is connected at the end of the SCSI chain install the supplied terminator to the other SCSI connector on the rear of ScanTouch If your ScanTouch is connected between the other SCSI devices no terminator on ScanTouch is necessary Since the terminator is built into the host computer in most cases the host computer should be at the end of the SCSI chain Some notebook computers require a terminator to be attached outside the computer please refer to the operation manual for the computer Note The SCSI cable used for SCSI connection should be of high impedance type a a a the other SCSI device ScanTouch Terminator E E i m oar ScanTouch the other SCSI device sae 2 the other SCSI device ScanTouch Terminator eo AI ao ScanTouch the other SCSI device Nikon ScanTouch 110 User s Manual 21 4 Connecting the Scanner Remarks v 22 The maximum number of SCSI devices that can be connected to one computer is eight including the CPU When using the scanner with a host computer with a built in SCSI hard disk or built in CD ROM note that SCS
4. oe 2 OL yono Leds D C O Q N E 8 5 E Nikon NIKON CORPORATION Electronic Imaging Division 4 25 Nishi Ohi 1 chome 6ME 51100 Shinagawa ku Tokyo 140 Japan Printed in Japan 9603 Nikon Flatbed Scanner ScanTouch 110 User s Manual il Cautions e The reproduction of all or part of this manual without our permis sion is prohibited e The information contained in this manual is subject to change without notice e We have made every effort to produce a perfect manual but should you find any mistakes we would be grateful if you would kindly let us know e We shall take no responsibility for consequences resulting from the operation of this product despite the terms mentioned above Indication The AN indications in this manual signify important safety precau tions In order to use this product safely please read every section where these indications are placed before beginning operation of this product These indications are also placed in the table of contents so users can find them easily Indication The V indications in this manual signify the need for caution when using the products These indications are placed in sections that should be read by users before beginning operation in order to avoid damage to the product Trademark Information Macintosh is a registered trademark of Apple Computer Inc Microsoft is a registered trademark and Windows is a trademark of Microso
5. Inspect the package to see whether any damage has occurred during shipment If there is any damage to the package please contact your retailer directly and do not unpack the unit 3 2 Components When you open the package check whether all the items are present If there are any missing items please contact your retailer immediately Main body 1 Nikon ScanTouch 110 User s Manual 11 3 Parts Identification SCSI cable 1 Power cord 1 50 pin full pitch 25 pin The shape of the plug depends on the country of use DEN We Fis User s manual s Software disk s Terminator 1 12 Nikon ScanTouch 110 User s Manual 3 Parts Identification 3 3 Main Body A Closer Look Document Cover Document Setting Glass Indicator Panel Document Cover Plastic cover over the document setting glass which can be raised and lowered over a document Document Setting Glass Glass surface on which the document or image should be placed Indicator Panel Contains Power Option and Ready indicators When you turn the power on and the test is initiated the indicators will flash once The Power indicator will then come on and the Ready indicator will blink When the test is completed the Power and Ready and Option if an option is connected indicators will glow steadily Nikon ScanTouch 110 User s Manual 13 3 Parts Identification Rear View 25 pin SCSI Connector Power Swi
6. 6 Maintenance 29 6 1 Static Electricity PrecautioNS w ww wwwwmmmmememea 29 62 ISH WA einen 30 T THOUDICSNOOUNG ii 31 Appendix Specifications cs ecccceeessseeeeeees 34 WA ii 36 viii Nikon ScanTouch 110 User s Manual 1 Overview 1 Overview Thank you for purchasing your Nikon Flatbed Scanner ScanTouch 110 This manual describes the procedures for unpacking setting up and connecting the scanner with emphasis on hardware use and precautions Please read this manual thoroughly to ensure proper operation of your scanner For an explanation of how to scan and reproduce images with ScanTouch 110 please refer to the software manual We hope that you will find this manual helpful ScanTouch 110 is a low priced full color flatbed scanner with high resolution and is capable of scanning images at high speed e The optical resolution is 300 dpi x 600 dpi and high resolution of 4800 dpi x 4800dpi is achieved through the software interpolation e The scanning area is 8 5 inches 216 mm wide by 11 7 inches 297mm long enabling scanning of letter size documents e It offers very high speed scanning of approximately 24 seconds for a color A4 size document at 300dpi e Installing the optional Transparency Adapter enables scanning of transparencies e Installing the optional Auto Document Feeder enables consecutive scanning of multiple documents Nikon ScanTouch 110 User s Manual 1 2 Be
7. and failure or electric shock The shape of the plug depends on the country of use e Do not extend the power cord of the product as this may cause a malfunction The shape of the plug depends on the country of use Nikon ScanTouch 110 User s Manual 3 2 Before Operating the Scanner 2 2 Handling Precautions WO i unlocked position Likewise turn the carriage lock on the e Before turning the power on ensure that the carriage lock is in the _ scanner to the locked position to avoid damaging the internal optical assembly during transportation _ Ly 100 240VAC OPT BB Remarks vA e Keep the unit horizontal with the document cover facing upward and ensure that it is placed on a flat and stable surface for use Failure may result if the unit is not used in a flat and level horizontal position 4 Nikon ScanTouch 110 User s Manual 2 Before Operating the Scanner e On no account disassemble the unit The high voltage components inside the unit can cause electric shock e Do not put any foreign objects inside the unit If flammable objects metal or water come into contact with the interior of the unit failure fire and or electric shock may result e Do not subject the unit to any strong shocks This can cause breakage and failure e Do not place any heavy objects on the document setting g
8. AC 0 5kV I O selon les dispositions de la directive de la CEE 89 336 EEC ERKLARUNG UBER EG NORMENGERECHTHEIT Wir Name Nikon UK Limited Anschrift Nikon House 380 Richmond Road Kingston Surrey KT2 5PR UK erkl ren hiermit da das folgende Produkt Produktbezeichnung Nikon ScanTouch 110 Name des Herstellers Nikon Corporation Anschrift des Herstellers Fuji Bldg 2 3 Marunouchi 3 chome Chiyoda ku Tokyo 100 Japan den nachstehend aufgef hrten Normen gen gt EN55022 Klasse B EN50082 1 IEC801 2 1984 8kV IEC801 3 1984 3V m IEC801 4 1988 IkVAC 0 5kV I O und zwar gem den Bestimmungen der EMC Richtlinie 89 336 EEC Kingston UK March 1 1996 ooo Place Date Signature Managing Director Lieu Date Signature Directeur g n ral Ort Datum Unterschrift Gesch ftsf hrer
9. I ID numbers have been preassigned for the host CPU and the SCSI devices The SCSI cable must not be extended beyond a total length of 19 feet 6 meters or else failure may result Terminators must be attached to the devices located at both ends of the SCSI chain If the host computer is a Macintosh the Macintosh itself will provide termination at one end of the chain If the host computer is an IBM PC AT or compatible equipped with a SCSI board the SCSI board itself will provide termination at one end of the chain Note that when a SCSI chain connection is made inside a computer the end of the SCSI device inside the computer will become the end terminal Before installing a SCSI board be sure to read the user s manual provided with the board The numbers for the I O address interrupt level INT and DMA channel might conflict with other interface boards and peripheral devices If so change them as explained in the manual Nikon ScanTouch 110 User s Manual 4 Connecting the Scanner 4 4 Setting the SCSI ID The SCSI ID for the ScanTouch 110 is set at 5 when the unit is shipped If other SCSI devices are connected to your computer make sure that the SCSI ID for the ScanTouch 110 is different from those assigned to other SCSI devices Note that in the case of a host computer which has a built in SCSI hard disk or built in CD ROM the ID numbers of the host CPU and each SCSI device have already been assigned
10. cur please check the following items before you assume that there is a unit failure For more details refer to the Troubleshooting section of the software manual If the Power indicator fails to come on e Make sure the power cable is plugged into the scanner and a wall socket e Make sure the power switch is on F 5 r E ADy POWER Power Indicator If neither of these two things is the cause of the problem please contact your dealer If the scanner lamp flickers is dim or fails to come on The scanning lamp is failing or has failed and needs to be changed Please contact your dealer Scanner Lamp Nikon ScanTouch 110 User s Manual 31 7 Troubleshooting If the Power and Ready indicators come on but software returns scanner link failed or a similar message 1 Make sure the cable is connected properly 2 Check the Installation procedure to make sure you followed all of the instructions Macintosh users should pay special attention to the setting of the SCSI ID number PC users should pay special attention to the I O address setting 3 Disconnect all SCSI devices and then reconnect them one by one beginning with the scanner to identify the device that is causing the problem 4 Check the terminators and the cables If the cable and terminators are all properly installed please contact your dealer Note f you are having intermittent problems either with the link between the scanner and yo
11. fore Operating the Scanner 2 Before Operating the Scanner 2 1 Power Supply Precautions In order to use the ScanTouch 110 safely and correctly and to prevent problems pay careful attention to the following points e Be sure to use an AC100V 120V AC 200V 240V 50 60Hz power supply The power cord should be changed according to the power voltage When using a power voltage of more than AC 125V Use a suitable power cord compliant with the safety standards of the country in which it is used with a plug of AC 250V ISA rating NEMA 6P 15 and insulation of at least SVT type and more than AWGIB in thickness When using a power voltage of AC 125V or less Use a suitable power cord compliant with the safety standards of the country in which it is used with a plug of AC 125V 10A rating and insulation of at least SVT type and more than AWGIS in thickness e Be sure that the electrical outlet of the power supply is grounded Carry out the grounding in common with the other machines it is being connected with Unless common grounding is used a ground loop will occur which will cause electric shock and noise static The shape of the plug depends on the country of use 2 Nikon ScanTouch 110 User s Manual 2 Before Operating the Scanner e Do not ground the unit to a gas pipe or a water pipe e When plugging in or unplugging the power cord be sure to touch only the plug Pulling on the cord can cause breakage
12. ft Corporation IBM PC AT is a trademark of International Business Machines Corporation Other brand or product names are the trademarks or registered trademarks of their respective holders Nikon ScanTouch 110 User s Manual Important Safeguard e Read all of instructions e Save these instructions for later use e Follow all warning and instructions marked on the product e When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original parts Unauthorized substitutions may result in fire electric shock or other hazards e Do not use this product near water or in rainy moist situation e Do not place on an unstable table to avoid the series damage to the product e The product should be operated only from the type of power source indicated on the marketing label e Do not attempt to service this product yourself as opening or removing the enclosure may expose you to dangerous voltage or other hazards e This unit has an autoranging input circuitary suitable 120VAC and 240VAC e The sound pressure level at the operators position according to IEC 704 1 1982 is equal or less than 70dB A Wichtige Sicherheitshinweise e Bitte lesen Sie sich diese Hinweise sorgfaltig durch e Heben Sie diese Anleitung f r den sp teren Gerauch auf e Alle Heiweise und Warnungen die sich am Ger ten befinden sind zu beachten e Wende
13. g from the use of this product Nikon ScanTouch 110 User s Manual U Notice concerning prohibition of copying or reproduction Note that simply being in possession of material which has been copied or reproduced by means of a scanner may be punishable by law UL Items prohibited by law from being copied or reproduced Do not copy or reproduce paper money coins securities govern ment bonds or local government bonds even if such copies or reproductions are stamped Sample The copying or reproduction of paper money coins or securities which are circulated in a foreign country is prohibited The copying or reproduction of unused postage stamps or post cards issued by the government without obtaining approval from the government is prohibited The copying or reproduction of stamps issued by the government and certified documents stipulated by law is prohibited Cautions on certain copies and reproductions The government has issued cautions on copies or reproductions of securities issued by private companies shares bills checks gift certificates etc commuter passes or coupon tickets except when a minimum of necessary copies are to be provided for business use by acompany Also do not copy or reproduce passports issued by the government licenses issued by public agencies and private groups ID cards and tickets such as passes and meal coupons Comply with copyright notices The copying or reproduction of wor
14. ic surface For example touch some large metal object or the silver toned expansion slot covers at the rear of your computer s case Be sure to do this immediately before removing any components from their antistatic bag When handling any electronic components be sure to carefully avoid touching any metal part of the component Avoid touching any of the gold fingers that plug into the expansion slot It is best to handle system components either by their edges or by the mounting bracket which attaches to the slot opening in the rear of the case Follow the above to the best of your ability Excessive caution is not necessary simply take reasonable care Nikon ScanTouch 110 User s Manual 29 6 Maintenance 30 6 2 Cleaning Regularly cleaning the document setting glass will ensure that dirt or smudges will not reduce the quality of your scanned images Before you clean the glass make sure the scanner is turned off and the power cord is unplugged Clean the document setting glass and document cover with a soft damp cloth and a mild detergent Note Avoid spraying the cleaning fluid directly on the glass as this may cause the liquid to penetrate the seams around the glass and contaminate the mirrors and lenses inside the scanner Please be sure to spray the liquid on the cleaning cloth and then wipe the glass clean Nikon ScanTouch 110 User s Manual 7 Troubleshooting 7 Troubleshooting When irregularities oc
15. is exposed to direct sunlight e The atmosphere is excessively dusty Nikon ScanTouch 110 User s Manual 2 Before Operating the Scanner e The unit may be subjected to excessive vibration e The unit is exposed to electrical noise and interference from other equipment nearby e When installing the scanner allow plenty of space around and above the unit to ensure smooth operation e When placing the unit on the table ensure that the unit does not stick off the edge of the table Nikon ScanTouch 110 User s Manual 9 2 Before Operating the Scanner 2 5 Transportation Precaution the carriage lock then pack the unit using the original packing material If the original packing material is not available be sure to pack it carefully paying attention to possible vibrations or shocks that may affect the precision equipment during transportation If transporting by air or delivery service the scanner should be packed with particular care When transporting the unit lock the scanning carriage in place using Before securing the locking screw first switch the unit on Once the scanning carriage has automatically returned to its home position approximately 30 seconds after the unit is switched on secure the locking screw Scanning carriage Home position Movement of the carriage YA 10 Nikon ScanTouch 110 User s Manual 3 Parts Identification 3 Parts Identification 3 1 Inspection
16. ks such as books music paintings woodcut prints maps drawings movies and photographs which are copyrighted creative works is prohibited except when it is done for personal use at home or for similar restricted and non commercial use Nikon ScanTouch 110 User s Manual Contents 1 OVERVIEW re 1 2 Before Operating the Scanner uuuuusnrennnnnnnennn 2 2 1 Power Supply Precautions suirusi 2 2 2 Handling Precautions uueressnnsnnsnssnnnnennnnnnnnnnnn nenn 4 2 3 If You Notice Anything Abnormal urer nennen 7 2 4 Storage and Operating Locations wwwwwwwwa 7 2 5 Transportation Precaution wa 10 3 Parts Identification zu 11 3 1 e e e E E T A une 11 3 2 COMM SMS ieii eee eect waa Kai kina kaua 11 83 Man BOY oerset eek 13 A Closer kw 13 PRON VION AWA 14 Unlocking the Scanner wwwwwwsewwmamwmaaimwamiamiwaa 15 4 Connecting the Scanner uuununssssnnnnnnnnnnnnnnnnnnn 16 4 1 Before Connection sisrsiririnirinriiii aniisi 16 4 2 Connecting the Power Cord 17 4 3 Connecting the SCSI Cable nn 19 Connecting to the Macintosh computer 20 Connecting to the IBM PC AT or compatible computer 20 SCSI Chain Connection with Other Devices 21 4 4 Setting the SCSI ID aa 23 Nikon ScanTouch 110 User s Manual vii 5 OPEN nina 24 5 1 Turning on the POWO Wa 24 5 2 Setting a Document seinen 26
17. l Internal 8 Bit Pixel Internal 1 Bit Pixel 1 to 200 in 1 Increments at 600 dpi Resolution 255 Steps 100 to 100 Downloadable Curves 24 Bit Hardware 24 Bit System 8 Bit Hardware 8 Bit System Built in SCSI 2 One 25 pin Connector and One 50 pin Connector 100 240V AC 50 60 Hz Maximum 52 Watts Nikon ScanTouch 110 User s Manual Appendix Specifications Environmental Ranges Operating Temperature 50 F to 104 F 10 C to 40 C Relative Humidity 20 to 80 Dimensions 13 3 W x 21 0 D x 5 7 H inches 336 x 534 5 x 144mm Net Weight 17 4 lbs 7 9 kg Systems Supported PC and Macintosh Options Transparency Adapter AT 10 Auto Document Feeder AF 10 Nikon ScanTouch 110 User s Manual 35 Index Symbols 25 pin SCSI Connector 14 50 pin SCSI Connector 14 A AC Inlet 14 Auto Document Feeder 1 Cc Carriage Lock 14 Cleaning 30 Components 11 Connecting the Power Cord 17 Connecting the Scanner 16 Connecting the SCSI Cable 19 Connecting to the IBM PC AT or compatible computer 20 Connecting to the Macintosh computer 20 D Document Cover 13 H Handling Precautions 4 If the Power indicator fails to come on 31 If the scanner lamp flickers is dim or fails to 31 Indicator Panel 13 M Main body 11 Maintenance 29 36 O optical resolution 1 Option Connector 14 P Parts Identification 11 Power cord 12 Power Supply 2 Power Switch 14 S scan
18. lass or push down on the glass as this can cause breakage and failure Nikon ScanTouch 110 User s Manual 5 2 Before Operating the Scanner e Take care not to scratch the surface of the document setting glass as this will affect the quality of the scanned images e Do not touch the pins of the SCSI connector as this may result in static damage e Do not pull or bend the connecting cable as this may cause the cable to break a i T e Do not move the unit or the document while the unit is scanning as this may affect the quality of the scanned images e Onno account look at the light source in the scanner as this may result in eye damage e Please clean the unit periodically Dust and dirt will affect the quality of the scanned images 6 Nikon ScanTouch 110 User s Manual 2 Before Operating the Scanner 2 3 If You Notice Anything Abnormal If you can notice unusual noise odor or smoke switch the unit off immediately and disconnect the power cord and the SCSI cable Contact your retailer or the Nikon sales representative in your country 2 4 Storage and Operating Locations Proper storage will ensure the long life of the unit Do not store or use where A e The temperature is above 95 F 35 C or below 50 F 10 C the temperature changes drastically or condensation occurs Nikon ScanTouch 110 User s Manual 7 2 Before Operating the Scanner e The humidity exceeds 80 e The unit
19. ll a SCSI board as explained in the manual supplied with the board Note Make sure that the PC is powered off before installing the SCSI board When installing a SCSI board for the first time be careful not to set conflicting I O addresses interrupt numbers or graphic board DMA channels Nikon ScanTouch 110 User s Manual 4 Connecting the Scanner 4 2 Connecting the Power Cord Before connecting the power cord confirm that the unit s power switch is in the off position Insert the female end of the supplied power cord into the AC inlet located on the rear panel then insert the plug into the AC power outlet The shape of the plug depends on the country of use Nikon ScanTouch 110 User s Manual 17 4 Connecting the Scanner Remarks g e The power source must be grounded e If possible try to use an independent electric outlet If the unit is connected to an outlet to which an electric household appliance such as a vacuum cleaner or air conditioner is connected the product may experience power source noise interference e Do not extend the power cord of the product as this may cause a malfunction The shape of the plug depends on the country of use 18 Nikon ScanTouch 110 User s Manual 4 Connecting the Scanner 4 3 Connecting the SCSI Cable Before connecting the SCSI cable confirm that all SCSI devices including the computer system have been turned off Power OFF Connect
20. n sie sich mit allen Fragen die Service und Reparatur betreffen an Ihren Servicepartner Somit stellen Sie die Betriebssicherheir des Ger tes sicher e Benutzen Sie dieses Produkt nicht in der N he von wasser oder in regerischer feuchter Umgebung e Stellen Sie es nicht auf eine unstabile Unterlage um Schaden an dem Produkt zu vermedien e Das Produkt sollte nur mit der auf dem Etickert angegebenen Stromquelle betrieben werden e Versuchen Sie nicht Reparaturen selber durchzuf hren da das ffnen oder die Entfernung des Geh uses Sie hoher Spannung oder anderen Gefahren aussetzt e Der Arbeitsplatzbezogene Schalldurckpegel nach DIN 45 635 betr gt 70db A oder weniger e Die Nerzanschlu steckdose Soll nahe dem Ger t angebracht und leicht zug nglich sein Nikon ScanTouch 110 User s Manual iii Federal Communications Commission FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interfer ence to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does ca
21. ning area 1 26 Scanning carriage 10 scanning transparency films for OHP 26 SCSI cable 12 SCSI Chain Connection with Other Devices 21 SCSI ID Switch 14 Setting a Document 26 Setting the SCSI ID 23 Specifications 34 Static Electricity Precautions 29 Storage and Operating Locations 7 T Terminator 12 Transparency Adapter 1 Transportation Precaution 10 Troubleshooting 31 Turning on the Power 24 U Unlocking the Scanner 15 Nikon ScanTouch 110 User s Manual EC DECLARATION OF CONFORMITY We Name Nikon UK Limited Address Nikon House 380 Richmond Road Kingston Surrey KT2 5PR UK declare that the product Product Name Nikon ScanTouch 110 Manufacturer s Name Nikon Corporation Manufacturer s Address Fuji Bldg 2 3 Marunouchi 3 chome Chiyoda ku Tokyo 100 Japan is in conformity with the following Standards EN55022 Class B EN50082 1 IEC801 2 1984 8kV IEC801 3 1984 3V m IEC801 4 1988 IkVAC 0 5kV I O following the provisions of the EMC Directive 89 336 EEC DECLARATION DE CONFORMITE DE LA CEE Nous Nom Nikon UK Limited Adresse Nikon House 380 Richmond Road Kingston Surrey KT2 5PR UK d clarons que ce produit Nom du produit Nikon ScanTouch 110 Nom du fabricant Nikon Corporation Adresse du fabricant Fuji Bldg 2 3 Marunouchi 3 chome Chiyoda ku Tokyo 100 Japan est conforme aux normes suivantes EN55022 Classe B EN50082 1 IEC801 2 1984 8kV IEC801 3 1984 3V m IEC801 4 1988 IkV
22. s Manual 5 Operation When the test is initiated the Power Ready and Option indicators will flash once The Power indicator will then come on and the ready indicator will blink When the test is completed the Power and Ready indicators will glow steadily OPTig N READy WER Remarks va e To turn the power off turn the host computer off first the other SCSI devices next and the ScanTouch last reverse order from switching on e Once the power is turned off please wait five seconds or more before turning the power on again e Do not turn the power off while the scanner is scanning Nikon ScanTouch 110 User s Manual 25 5 Operation 5 2 Setting a Document e The scanning area is 8 5 inches 216 mm wide by 11 7 inches 297mm long enabling scanning of letter size documents effective scanning area e For scanning transparency films for OHPs overhead transparencies place a sheet of white paper on top e Ifthe document is curled or creased make sure that it is straightened and flattened before setting it in position e Ifthe paper has staples or clips attached make sure they do not scratch the surface of the glass 26 Nikon ScanTouch 110 User s Manual 5 Operation Step 1 Open the document cover gently Nikon ScanTouch 110 User s Manual 27 5 Operation Step 2 Position a document with the side to be scanned facing down aligning it with the appropriate mark on the ruler
23. tch og 4 AC Inlet IT Option Connector ormon 50 pin SCSI Connector SCSI ID Selection Switch Carriage Lock When transporting the unit fasten the screw to lock the carriage AC Inlet Connect to the AC power source with the power cord provided Power Switch Directly turns the AC power on off Option Connector This connector is for use with a Transparency Adapter or an Automatic Document Feeder 25 pin SCSI Connector For 25 pin SCSI cable connection 50 pin SCSI Connector For 50 pin SCSI cable connection SCSI ID Selection Switch Sets the SCSI ID number Numbers 0 to 7 are shown and valid 14 Nikon ScanTouch 110 User s Manual 3 Parts Identification Unlocking the Scanner Before using the power on ensure that the carriage lock is in the unlocked position Likewise turn the carriage lock on the scanner to the locked position to avoid damaging the internal optics during transportation LALA OPTION Nikon ScanTouch 110 User s Manual 15 4 Connecting the Scanner 4 4 1 16 Connecting the Scanner Before Connection Before connecting the cables confirm that all devices including the computer system and the scanner are turned off 6 Power OFF For an IBM PC AT or compatible in which a SCSI board has not been installed insta
24. the unit to the computer using the provided SCSI cable After attaching the connector be sure to lock it in place You can connect the SCSI cable to either of the SCSI connectors 50 pin and 25 pin on the rear panel of the unit Caution Do not touch the pins of the SCSI connector This can result in static damage Nikon ScanTouch 110 User s Manual 19 4 Connecting the Scanner 20 Connecting to the Macintosh computer When connecting the unit directly to your Macintosh computer connect the 25 pin connector to the computer and the 50 pin connector to the unit If the unit is the only connected SCSI device or if the unit is connected at the end of the SCSI chain attach the supplied SCSI terminator between the 50 pin SCSI connector on the unit and the SCSI cable as shown below A SS LIL mn o M Terminator 50 pin connector 25 pin connector Connecting to the IBM PC AT or compatible computer When connecting the unit directly to the IBM PC AT or compatible computer connect the 50 pin connector to the computer and the 25 pin connector to the unit If the unit is the only connected SCSI device or if the unit is connected at the end of the SCSI chain attach the supplied SCSI terminator to the 50 pin SCSI connector on the unit as shown below 25 pin connector x T m
25. ur computer or are having intermittent problems with the results of your scans try installing an external SCSI terminator 32 Nikon ScanTouch 110 User s Manual 7 Troubleshooting If All Else Fails If the above solutions do not resolve the problem contact your dealer Be sure to have the following information available 1 ND wn A W N The scanner model you are using The version number of the scanner driver The computer model you are using All SCSI devices that you are using The application software packages that you are using Error codes or messages seen A description of what you were doing at the time the malfunction or failure occurred Other observations that may aid the technician in identifying the problem and solution Nikon ScanTouch 110 User s Manual 33 Appendix Specifications Appendix Specifications 34 Scan Speed Preview Speed 24 Seconds A4 300 dpi Color Mode 6 Seconds A4 Color Mode at 100dpi 3 5 Seconds A4 Gray Line art Mode at 100dpi Maximum Scannable Area Optical Resolution Color Scanning Method Sample Depth Color Mode Grayscale Mode Line Art Mode Scanner Settings Scaling Highlight Shadow Contrast Brightness Gamma Curve Data Output Color Mode Grayscale Mode Interface Power Requirements Voltage Frequency Power Consumption 216 x 297 mm 8 5 x 11 7 Inches 300 x 600 dpi One pass with color CCD 24 Bit Pixe
26. use harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help CAUTION Modifications The FCC requires the user to be notified that any changes or modifica tions made to this device that are not expressly approved by Nikon Corporation may void the user s authority to operate the equipment SCSI Cable Please use the SCSI cable listed on page 5 in the user s Manual sup plied with the scanner Using other interface cables may exceed the limits of the class B Part 15 of FCC rules LU Nikon ScanTouch 110 User s Manual Notice for customers in Canada This class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations ATTENTION Cet appareil num rique de la class B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada When Taking the Unit Out of The Country The use of this product may violate local laws and restrictions in some countries If this is the case we cannot bear any responsibility for any violations resultin
Download Pdf Manuals
Related Search