Home
Newcon Optik LRB 3000PRO Binoculars User Manual
Contents
1. 1 Accuracy of correction will depend on accuracy of installation against target If distance is 0 9 meters then unit will have 0 1 m offset during all future measurements 15 2 Target should not have high reflective surface white color is not considered high reflective in this case 3 Unit shall be well leveled with deviation from 0 not more than 0 75 degrees Horizontal direction shall be to Magnetic North not True North If devices detects large installation errors unit is not well leveled or not aimed to the North then LCD will show result 444 which means that correction was not performed due to incorrect setup Compass calibration If the System was exposed to a strong magnetic field or was not in use for a long time the compass accuracy may diminish To return the compass into working condition Select CALc from CAL menu Keeping the unit horizontally perform one full rotation 360 around vertical axis within a minute If one rotation does not restore calibration perform two rotations per a minute The normal compass functioning will be restored 16 Data Recall mode In Data Recall mode results of the last 10 measurements can be displayed Measurement results are saved in on board memory in sets depending on the parameters set for measuring for instance if only distance is measured the set will consist of one number if distance and azimuth are measured t
2. at a sharp angle to the beam Weather conditions that influence air transparency rain fog snow mist reduce maximum range Bright sunny days will reduce performance as well as IR sun radiation may cover reflected laser impulses While the unit will measure through many glass types measuring through glass may reduce accuracy Natural hand tremor decreases the accuracy of long distance ranging Using of a tripod is highly recommended Note device may produce false readings when reticle is aimed at the sun or in 20 solid angle from the sun Target selection logic On its way towards the target laser beam may reflect from various objects thus decreasing ranging accuracy The 11 smaller the farther and the less reflective is the target the higher is the possibility of obtaining an incorrect measurement To improve accuracy the unit has a built in target selection logic that allows choosing which target to range the nearest first the farthest last or the most reflective auto This mechanism helps selecting the target when ranging from behind the bushes wires through the falling snow or in similar conditions Similarly it enables ranging a target in front of a bigger object such as a wire in front of the wall Note Even with target selection logic the unit may not always be able to range the desired target as its reflectivity may be too low to produce enough laser beam reflections for st
3. found to be defective in materials or workmanship What This Warranty Does Not Cover NEWCON is not responsible for warranty service should the product fail as a result of improper maintenance misuse abuse improper installation neglect damage caused by disasters such as fire flooding lightning improper power supply or service other than by a NEWCON Authorized Service Postage insurance and shipping costs incurred while presenting your NEWCON product for warranty service are your responsibility If shipping from North America please include a cheque or money order payable to NEWCON OPTIK for the amount of US 15 00 to cover handling and return shipping 21 10 CUSTOMER SUPPORT Should you experience any difficulties with your NEWCON OPTIK product consult the enclosed manual If the problem remains unresolved contact our customer support department at 416 663 6963 or toll free at 1 877 368 6666 Our operating hours are 9am 5pm Monday Friday Eastern Standard Time At no time should equipment be sent back to Newcon without following the instructions of our technical support department NEWCON OPTIK accepts no responsibility for unauthorized returns To locate NEWCON Authorized Dealer call Tel 416 663 6963 Fax 416 663 9065 Email newconsales newcon optik com Web www newcon optik com The defective products should be shipped to US customers 2331 Superior Ave Cleveland OH 44114 From all other countri
4. LE OF CONTENTS 1 BRIEF DESCRIPTION Principle of operation gt 1 N DEVICE APPEARANCE 3 DELIVERY SE Trinn E ournetisasvrenactes Standard delivery Set es Optional accesSOTleS 4 SPECIFICATIONS S neooni 5 OPERATION INSTRUCTIONS Preparing device for operation pp 9 Measurement 0106601006 RN Factors affecting measuring distance pp Target selection logic Individual Measurement and Scanning regimes Operation and service modes RN Accuracy Correction Compass cahbration Data Recall mode Ne 6 BEST MEASURING TECHNIOUE ths STORAGE AND MAINTENANCE 8 TROUBLESHOOTING RN 9 WARRANT Y 2 10 CUSTOMER SUPPORT 11 QUALITY CERTIFICATE CAREFULLY READ ALL THE INSTRUCTIONS BEFORE USING FAILURE TO OBEY THE INSTRUCTIONS WILL VOID THE WARRANTY 1 BRIEF DESCRIPTION The LRB 3000PRO Laser Rangefinder Binoculars System is an advanced laser range finder that enables instant distance sp
5. No NEWCON OPTIK Operation Manual LRB 3000PRO LASER RANGE FINDER BINOCULARS 105 Sparks Ave Toronto ON M2H 2S5 Canada 1 IMPORTANT INFORMATION Read prior to activation You have just purchased a sophisticated electro optical device that emits invisible laser radiation To operate it properly please read this manual carefully NEVER direct laser beam at the eyes of people or animals NEVER aim the unit at the Sun or bright sources of light NEVER subject the unit to impacts NEVER transport the unit without its case NEVER disassemble the unit This may be hazardous for you due to high voltage currents ALWAYS keep the unit out of the reach of children ALWAYS remove the battery when the device is not in use for a long period ALWAYS store the unit in a dry place Caution use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure Caution use of optical instruments such as binoculars loupes mirrors lenses etc with this product increases eye hazard Avoid eye exposure to direct laser beam or its close reflection Prevent bright light from focusing through the eyepieces iii e Never aim the unit at highly reflective objects like mirrors and retroreflective surfaces which are in close proximity to the laser rangefinder This can lead to the permanent damage of the photoreceiver incorporated into the device iv TAB
6. atistically reliable calculation Individual Measurement and Scanning regimes The unit can operate in two regimes 1 Individual Measurement and 2 Scanning In the Individual Measurement regime the unit performs single measurement when the A button is pressed shortly in Scanning regime the unit repeatedly measures and displays results every second while the A button is pressed To activate the Scanning regime press and hold the A button in the Ready mode The unit will work in the Scanning regime while the A button is pressed The Scanning or Individual Measurement regimes are available for any selected mode of measurement When two 12 parameters are measured in the Scanning regime though both will be quickly displayed the second one may be difficult to register by eye Nevertheless all data is recorded and may be recalled see Data Recall mode for details Operation and service modes Pressing Mode button 3 Fig 1 in Ready mode switches the unit between modes of operation to activate any desired mode from the menu you must confirm your selection by pressing Action button 4 Fig 1 The unit has the following modes of operation Ready Unit is ready to perform measurements dFLt sets default mode of operation with factory settings Std allows the user to select single action measurements o Distance only o Compass Only o Speed Only o Speed Distance o Distance Compass Unit allows user to se
7. e Target Selection Logic may be used For example if ranging a wire in front of a building selecting the first target will produce a more reliable result Alternatively when aiming at a chimney behind the trees selecting last target will be better By default the System assumes auto target selection i e the object producing the most of reflections will be considered a target 18 7 STORAGE AND MAINTENANCE The unit is a sophisticated precision optical instrument equipped with laser and electronics Therefore it should be handled with due care Keep it away from direct sunlight Avoid impacts jolts dust moisture and sharp changes of temperature Do not use the device at temperatures higher than 50 C 122 F Do not touch optical surfaces Doing so may damage the anti reflection coating Clean optical surfaces only with professional camera lens cleaning supplies Clean the exterior of the unit with a soft clean cloth Keep away from heating appliances and central heating Remove the battery when storing the device for long time All repair works must be performed by an authorized service Prevent bright light from focusing through the eyepiece 19 8 TROUBLESHOOTING Ranging does not work The display is transparent Check the charge of the battery Replace it if it is weak Ranging does not work The display indicates results of the last measurement Wait until display becom
8. eed and angular measurements The unit complies with CFR 21 Part 1040 10 and Part 1040 11 An outstanding fully multi coated optics coupled with an original circuitry design creates a system that outperforms any other product in its class and price range Principle of operation The unit sends invisible eye safe laser beam pulses to the target The pulses reflected from the target are captured and processed by the digital circuitry The time of flight delay between the sent and received pulses allows calculating the distance to the target A built in digital compass measures azimuth simultaneously with ranging Key Features Modern digital circuitry allows targeting through most types of glass Speed detector Selection of the first last or the most reflective target Distance is displayed in meters or yards Original digital circuitry allows ranging through most types of glass bushes and other obstacles Three channel optical solution optical laser and receiver provides high accuracy Two reticle shapes or Built in digital compass On board memory keeps results of last 10 measurements that can be recalled to the LCD The unit automatically turns off when no button is pressed for 8 seconds 2 DEVICE APPEARANCE Fig 1 Front view 2 Objective lens 4 Action button 6 Rubber grip 1 Eyepieces 3 Mode button 5 Battery compartment cover Fig 2 Rear View 1 Eye
9. es 105 Sparks Ave Toronto ON M2H 2S5 CANADA 22 11 QUALITY CERTIFICATE Serial number The unit has passed the quality inspection Production date Quality Inspector Purchase date 23 1 8 NEWCON OPTIKTM 1
10. es transparent and press the Action button again Compass readings are equal to zero at any direction Wait until display becomes transparent and press the Action button again If this does not help perform the compass calibration Black dots are visible on LCD Liquid Crystal Display may have small black dots scratches and other blemishes inherited from the manufacturing process These flaws are strictly regulated by number area and location and do not degrade the product s measurement capabilities Range measurement cannot be obtained e Make sure that neither your hand nor finger is blocking objective lens laser emitting lens or receiver lens e Hold the unit firmly avoid hand tremor while pressing the Action button e Check that the target is within measuring range of the device and the gating mode does not cut it off 20 9 WARRANTY NEWCON warrants this product against defects in material and workmanship for one year from the date of the original purchase Longer warranty is available subject to the terms of the specific sales contract Should your Newcon product prove to be defective during this period please deliver the product securely packaged in its original container or an equivalent along with the proof of the original purchase date to your Newcon Dealer Newcon will repair or at its option replace with the same or comparable model the product or part thereof which on inspection by Newcon is
11. he set will consist of two numbers To enter Data Recall mode select lt 2 from main menu First measurement set number display name FEC 1 will start flashing Pressing M button moves the unit along the list of measurement set numbers and measurement results rEc 1 distance 1 azimuth 1 rEc 2 distance 2 azimuth 2 rEc 0 distance 0 azimuth 0 Measurement sets are numbered in reverse order first recalled set is the result of the last measurement If any parameter has not been actually measured it will not be recalled Pressing A button at any moment within the list of recalled results brings the unit to Ready to Measure mode Choosing CLY at the end of recalled data will erase the device memory 17 6 BEST MEASURING TECHNIQUE Laser range finder measures distance by catching laser beam reflected from the target Everything that improves reflection increases the measurement reliability and maximum range 1 Use tripod when ranging remote targets The longer is the distance the greater is the beam shift due to hand tremor 2 Aim the unit at a surface on the target that is the closest to perpendicular to the laser beam The better perpendicular to the target the stronger will be the reflection 3 The unit deploys sophisticated software that tries to understand which target you are aiming at However due to beam divergence several objects may produce a strong reflection To help the System recognise the target th
12. it press and hold Action button 6 Fig 1 for one second At start the unit comes into Ready to Measure mode indicated by the word READY on the display visible through the eyepiece Pressing Action button 6 Fig 1 again will initiate measurement procedure The results of measurement are displayed in default form of Distance M and Azimuth mils measurement parameters which also can be modified to user preference see Operation and service modes If results of measurement are unreliable four dashes will be displayed in the area 4 Fig 3 Pressing Mode button 3 Fig 1 gives the user the options to change settings from Factory default to specific modes required by user For full list of Mode options please refer to Operation and Service modes 10 Factors affecting measuring distance Though maximum measurement distance depends on target reflectivity weather conditions and other conditions for most targets the unit will provide accurate ranging for up to 2 500 meters Under good conditions a large size target can be measured up to 3 000 meters Target reflectivity depends on its color surface finish size shape position in relation to the laser beam etc Bright target colors are more reflective than darks A polished surface is more reflective than a rough one Larger targets reflect better than small ones Ranging a target perpendicular to the laser beam provides better results than the one positioned
13. lect units of measurements O Distance from M to Y 13 o Compass from Mils to Degrees o Speed from KMH to MPH rEc allows data recall of the last 10 measurement results o CLr Clears all Measurement SEt allows the user to select the following advanced options FrSt First Target Measurement LASt Last Target Measurement AUtO Last Target Measurement Reticule Change reticule from cross to J rectangle 6 O OQ o CAL Calibration and correction CALc compass calibration Corr accuracy correction of active measurement parameters not shown in the menu if currently selected this option is only available if Std Speed is selected 14 Accuracy correction If the System produces some measurement errors that lie beyond unit specification it may be an indication that unit requires calibration similar to one conducted at production level To do accuracy correction please select Corr from CAL menu Perform correction according to required measurement parameters by pressing Action button see table below Active mode of Correction iti measurement Std parameter Condition Install unit at 1 meter S Sd d 706 from flat target Put unit in a level plane C Azimuth Jand aim it to the North direction Install unit at 1 meter from flat target controlling its level position and direction to the North Distance and aC azimuth
14. pieces 7 Interpupillary distance adjustment lever 8 Identification and certification label located at the bottom Ce PATENT PENDING NEWCON OPTIK 105 SPARKS AVE TORONTO ON CANADA M2H 2S5 THIS PRODUCT COMPLIES WITH CFR 21 1040 10 1040 11 MADE IN CANADA MODE READY Fig 3 Display 1 Low battery indicator 2 Reticle either or 1 3 Units of measurement 4 Measurement result 5 Laser active indicator 6 Ready mode indicator 7 Setup mode indicator 3 DELIVERY SET Standard delivery set LRB is supplied in the following assembly Qty LRB 3000PRO Carrying case Neck strap Operation manual 9V non magnetic Lithium battery Warranty card a ee Optional accessories Hard case 4 SPECIFICATIONS Optics Magnification 7x Objective lens diameter 40 mm Exit pupil diameter 5 7 mm Field of view 6 Type of coating Fully multi coated optics Range Finder Laser Class 1 eye safe 905 nm Measuring range 10 3 000 m Accuracy 1m First last and auto target selection Yes Meters Yards display Yes Last 10 readings recall Yes Reticle izor O Speed measurement Measured speed range 5 400 km h 3 250 mph Accuracy km h or mph 2 Compass Measured azimuth range 360 Accuracy 27 Power Battery 9V Lithium non magnetic Battery capacity Min 5 000 measurements Scanning regime Low Batte
15. ry indicator Yes Environmental Operational temperature range 25 50 C 13 122 F Storage temperature range 45 65 C 49 149 F Mechanics Tripod thread a x 20 TPI Weight without battery 970 g Dimensions 158x145x70 mm 5 OPERATION INSTRUCTIONS Preparing device for operation Rotate the battery compartment cover 5 Fig 1 counter clockwise and pull it open Connect and insert battery into the battery compartment Close the battery compartment cover 5 Fig 1 Adjust the interpupillary distance with lever 7 Fig 2 Adjust the eye relief distance by moving collapsing eyepieces 1 Fig 1 in lengthwise direction The unit is fully operational when battery voltage is over 6 3V A LOW BATTERY warning is displayed voltage falls below 6 5V The unit may be powered with 9V batteries capable to sustain 350 mA current drain e Standard 9V battery may be used as a short term solution It will last for about 30 45 minutes of continuous operation e 9 Lithium non magnetic battery guarantees over 5 000 shots at room temperature It is recommended for the field usage In addition this battery does not influence the internal compass Note Metal housing of the battery may degrade the compass accuracy Measurement procedure The LRB 3000PRO operational procedures are design to allow the user to use most applicable options in the fastest time possible To activate
Download Pdf Manuals
Related Search
Related Contents
INSTRUCTION MANUAL Nissan Armada Captains Chair Se PDFファイル - 医薬品医療機器総合機構 MODULAR OCCUPANT/ ATTENDANT USER GUIDE Samsung PS42A450P1 راهنمای محصول Bulletin technique N°1 manuel d`instructions pour ponceuse de paume 1/4 Chrysler 2004 Pacifica Automobile User Manual User Manual GE LOGIQ e user guide Copyright © All rights reserved.
Failed to retrieve file