Motorola T3 Network Router User Manual
Contents
1. Trimmer Line Tap Button Line Limiter Blade ASSIST HANDLE The ASSIST HANDLE is used to help hold and guide the unit TRIMMER HEAD The TRIMMER HEAD holds cutting line and rotates during operation TAP BUTTON The TAP BUTTON is used to advance the cutting line during operation and to remove the spool during line replacement ATTACH THE EXTENSION CORD TO YOUR TRIMMER Loop your extension cord through the handle and around the hook as shown Insure the plug and cord are firmly and fully engaged Cord Retainer Extension Cord CORRECT OPERATING POSITION Y Trimming A WARNING Always wear eye protec tion Never lean over the trimmer head Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury When operating unit stand as shown and check for the following e Wear eye protection and heavy clothing e Hold trigger handle with right hand and as sist handle with left hand Keep unit below waist level e Cut only from your right to your left to en sure debris is thrown away from you With out bending over keep line near and paral lel to the ground and not crowded into material being cut ADVANCING THE CUTTING LINE Advance line by tapping bottom of cutting head lightly on the ground while unit is running at full speed A metal line limiter blade at tached to the shield will cut the line to the proper length A WARNING Use only 0 065 inch 1 62. WEED EATER Trademark Por favor no devuelva el aparato al lugar de compra 9 Please do not return unit to retailer Veuillez ne pas retourner l outil au d taillant 1 800 554 6723 www weedeater com Instruction Manual Manual de Instrucciones Manuel d Instructions RT110 RT112 c US WARNING Read and follow all Safety Rules and Operating Instructions before using this product Read instructions carefully before assembling Failure to do so can result in serious injury ADVERTENCIA Lea el manual del operador y siga todas las advertencias e instruc ciones de seguridad Antes de ensamblar el producto lea cuidado samente el instructivo El no hacerlo puede resultar en lesiones gra ves AVERTISSEMENT Veuillez lire le manuel de l utilisateur et bien respecter tous les avertissements et toutes les instructions de s curit Bien lire les instructions avant d assembler l outil Tout d faut de le faire pourrait entra ner des blessures graves Electrolux Home Products Inc Electrolux Canada Corporation 250 Bobby Jones Expressway 6150 McLaughlin Road Augusta GA 30907 Mississauga Ontario L5R 4C2 2 From the Electrolux Group The world s No 1 choice KITCHEN CLEANING AND OUTDOOR APPLIANCES COMBINED Copyright 2003 WCI Outdoor Products Inc 530086725 2 11 03 JOEPIE TONVWdS43 SIVONVHS SAFETY RULES A WARNING When using electric gar dening appliances basic safety precautions must
3. always be followed to reduce the risk of fire electric shock and serious injury Read and follow all instructions SAFETY INFORMATION ON THE UNIT This power unit can be dangerous Operator is responsible for following the warnings and instructions in this manual and on the unit Read entire instruction manual before using unit Be thoroughly familiar with the controls and the proper use ofthe unit Restrict the use of this unit to persons who read understand and follow unit and manual warnings and instructions Never allow children to operate this unit Close attention is necessary when used near children A DANGER Never use blades or flail ing devices Unit is designed for line trimmer use only Use of any other accessories or at tachments will increase the risk of injury 00 A WARNING Trimmer line throws ob jects violently You and others can be blinded injured Wear safety glasses boots and leg protection Keep body parts clear of rotating line Safety Glasses or similar eye protection Keep children bystanders and animals 50 feet 15 meters away lf approached stop unit immediately If situations occur which are not covered in this manual use care and good judgement If you need assistance call 1 800 554 6723 OPERATOR SAFETY e Dress properly Always wear safety glasses or similar eye protection when op erating or performing maintenance on your unit Safety glasses are available Always we
4. each use TRANSPORTING AND STORAGE e Stop the unit and disconnect the power source when not in use Carry the unit with motor stopped Store the unit so the line limiter blade on underside of shield cannot cause injury Store unit indoors in a high dry place out of the reach of children Store unit unplugged Do not hang unit so that the trigger switch is depressed DOUBLE INSULATION CONSTRUCTION This unit is double insulated to help protect against electric shock Double insulation construction consists of two separate layers of electrical insulation instead of grounding Tools built with this insulation system are not intended to be grounded No grounding means is provided on this unit nor should a means of grounding be added to this unit As a result the extension cord used with your unit can be plugged into any standard 120 volt electrical outlet Safety precautions must be observed when operating any electrical tool The double in sulation system only provides added protec tion against injury resulting from an internal electrical insulation failure WARNING All electrical repairs to this unit including housing switch motor etc must be diagnosed and repaired by qual ified service personnel Replacement parts for a double insulated appliance must be rec ommended by the manufacturer A double in sulated appliance is marked with the words double insulation or double insulated The symbol s
5. will fit into a polarized exten sion cord only one way If the plug does not fit fully into the extension cord reverse the plug If the plug still does not fit obtain a correct polarized extension cord A polar ized extension cord will require the use of a polarized wall outlet This plug will fit into the polarized wall outlet only one way If plug does not fit fully into the wall outlet re verse the plug If it still does not fit contact a qualified electrician to install the proper wall outlet Do not change the equipment plug extension cord receptacle or extension cord plug in any way To reduce risk of electrical shock use ex tension cords specifically marked as suit able for outdoor appliances having electri cal rating not less than the rating of unit Cord must be marked with suffix W A in Canada W Make sure your extension cord is in good condition Inspect extension cord before use and replace if damaged Do not use a damaged cord Cord insulation must be intact with no cracks or deteriora tion Plug connectors must be undamaged An undersized extension cord will cause a drop in line voltage resulting in loss of pow er and overheating If in doubt use the next heavier gauge The lower the gauge num ber the heavier the cord see SELECT AN EXTENSION CORD in the OPERATION section e Do not use multiple cords Do not abuse cord Never carry the unit by the extension cord or yank extension cord to
6. 5 mm diameter line Other sizes of line will not ad vance properly and will result in improper cutting head function or can cause serious injury Do not use other materials such as wire string rope etc Wire can break off during cutting and become a dangerous missile that can cause se rious injury See page 2 for warning concerning other cutting devices TRIMMING Hold the bottom of the trimmer head about 3 inches 8 cm above the ground and at an an gle Allow only the tip of the line to make con tact Do not force trimmer line into work area Trimming 3 in 8 cm Above Ground SCALPING The scalping technique removes unwanted vegetation down to the ground Hold the bot tom of the trimmer head about 3 inches 8 cm above the ground and at an angle Allow the tip of the line to strike the ground around trees posts monuments etc This technique in creases line wear Scalping MOWING Your trimmer is ideal for mowing in places conventional lawn mowers cannot reach In the mowing position keep the line parallel to the ground Avoid pressing the head into the ground as this can scalp the ground and dam age the tool Mowing SWEEPING The fanning action of the rotating line can be used for a quick and easy clean up Keep the line parallel to and above the surfaces being swept and move the tool from side to side MAINTENANCE A WARNING Disconnect unit from the power source before performing main
7. E OTHER RIGHTS WHICH VARY FROM STATE TO STATE NO CLAIMS FOR CONSEQUENTIAL OR OTHER DAMAGES WILL BE ALLOWED AND THERE ARE NO OTHER EXPRESS WARRANTIES EXCEPT THOSE EX PRESSLY STIPULATED HEREIN SOME STATES DO NOT ALLOW LIMITA TIONS ON HOW LONG AN IMPLIED WAR RANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CON SEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU The policy of ELECTROLUX HOME PROD UCTS INC is to continuously improve its products Therefore ELECTROLUX HOME PRODUCTS INC reserves the right to change modify or discontinue models de signs specifications and accessories of all products at any time without notice or obliga tion to any purchaser
8. Pull on the line extending outside the hub to release it from the notch otherwise the unit will not function properly 5 Insert one end of the line about 1 2 inch 1 cm into the small hole inside the spool 6 Wind the line evenly and tightly onto the spool Wind in the direction of the arrow found on the spool 7 Push the line into the notch leaving 3 to 5 inches 7 12 cm unwound Hub 8 Insert the line into the exit hole in the hub u Line exit hole as shown in the illustration 9 Align the notch with the line exit hole 10 Push the spool into the hub until it snaps into place USER REPLACEABLE SERVICE PARTS REPLACEMENT PART PART NUMBER Spool with 0 065 Trimmer Line 952701663 Assist Handle 530403805 Bolt Carriage 1 4 20 530403886 Wing Nut 530016152 Shield Assembly RT110 530404080 Shield Assembly RT112 530404076 STORAGE e Store unit and extension cord indoors ina WARNING Perform the following high dry place out of the reach of children steps after each use Store unit unplugged e Stop the unit and disconnect the power Store unit with all guards in place Position source when not in use unit so that any sharp object cannot acci e Carry the unit with motor stopped dentally cause injury e Store the unit so the line limiter blade can not cause injury TROUBLESHOOTING TABLE A WARNING Always stop unit and disconnect from the power source before performing all of the rec
9. ar face or dust mask if operation is dusty Always wear heavy long pants long sleeves boots and gloves Do not go bare foot or wear sandals Secure hair above shoulder length Secure or remove loose clothing and jewelry or 2 clothing with loosely hanging ties straps tassels etc They can be caught in moving parts Being fully covered also helps protect you from debris and pieces of toxic plants thrown by spinning line Stay Alert Do not operate unit when you are tired ill upset or under influence of al cohol drugs or medication Watch what you are doing use common sense Avoid unintentional starting of the unit Never carry unit with your finger on the switch Be sure the switch is in the OFF position and never touch the switch when connecting extension cord ELECTRICAL SAFETY A WARNING Avoid a dangerous envi ronment To reduce the risk of electrical shock do not use in rain in damp or wet loca tions or around swimming pools hot tubs etc Do not expose to snow rain or water to avoid the possibility of electrical shock e Use a voltage supply as shown on unit e Avoid dangerous situations Do not use in the presence of flammable liquids or gases to avoid creating a fire or explosion and or causing damage to unit To reduce the risk of electrical shock this equipment has a polarized plug one blade is wider than the other and will require the use of a polarized extension cord The ap pliance plug
10. disconnect unit e Use cord retainer to prevent disconnection of extension cord from unit and possible damage to the unit due to plug movement see ATTACH THE EXTENSION CORD TO YOUR TRIMMER in the OPERATION section Do not use the unit if the switch does not turn the unit on and off properly Repairs to the switch must be made by your autho rized service dealer e Keep the extension cord clear of operator and obstacles at all times Do not expose cords to heat oil water or sharp edges To avoid the possibility of electric shock avoid body contact with any grounded con ductor such as metal fences or pipes e Ground Fault Circuit Interrupter GFCI protection should be provided on circuit or outlet to be used Receptacles are avail able having built in GFCI protection and may be used for this measure of safety UNIT SAFETY e Inspect unit before use Replace damaged parts Make sure all handles guards and fasteners are in place and securely fas tened Parts that are damaged must be re paired or replaced by an authorized service dealer These include head parts that are cracked or chipped guards and any other part that is damaged e Do not repair unit yourself e Use only 0 065 in 1 65 mm diameter rec ommended trimmer line see USER RE PLACEABLE SERVICE PARTS in the SERVICE AND ADJUSTMENTS section Never use wire rope string etc Use specified trimmer spool Make sure spool is properly installed a
11. he shield onto the motor housing Ensure the cutting head remains free to rotate and the line is not caught between the shield and the motor housing 3 Twist the shield as illustrated until it snaps securely into place Make sure the shield is assembled to the unit as shown in the illustration below and in the KNOW YOUR UNIT section of this manual ALIGN INSTALLATION ARROWS Twist shield in direction of arrow to assemble CAUTION Sharp line limiter blade OPERATION KNOW YOUR TRIMMER READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments Save this manual for future reference Cord Retainer Recessed Plug RECESSED PLUG The RECESSED PLUG is where you attach your extension cord to the unit TRIGGER SWITCH The TRIGGER SWITCH is used to turn on the unit Squeeze the trigger switch to operate the unit Release to stop LINE LIMITER BLADE The LINE LIMITER BLADE cuts the cutting line to the proper cutting length OPERATING INSTRUCTIONS Use only a voltage supply as specified on your unit SELECT AN EXTENSION CORD Extension Cord Gauge Chart Length of Cord Gauge 25 Ft 7 5 m 18 Gauge 50 Ft 15 m 16 Gauge 100 Ft 30 m 16 Gauge Extension cords are available for this unit Assist Handle Motor Housing Trimmer Head with 0 065 in
12. nd all parts are securely fastened e Use only Weed Eater replacement parts and accessories as recommended CUTTING SAFETY WARNING Inspect area to be cut Remove objects rocks broken glass nails wire string etc which can be thrown or be come entangled in cutting head Do not overreach or stand on unstable sup port Keep firm footing and balance e Keep the cutting head below waist level Do not raise handles above your waist Cutting head can come dangerously close to your body Keep away from cutting head and spinning ine Use unit properly Use only for trimming scalping and mowing Do not force unit It will do the job better and with less risk of in jury at the rate for which it was designed e Use only in daylight or in good artificial light MAINTENANCE SAFETY A WARNING Disconnect unit from the power supply before performing mainte nance or when changing trimmer line e Maintain unit according to recommended procedures Keep cutting line at proper length Follow instructions for changing trimmer line Have all service and maintenance not ex plained in this manual performed by an au thorized service dealer to avoid creating a hazard Never douse or squirt the unit with water or any other liquid Clean unit and labels with a damp sponge Keep handles dry clean and free from oil and grease Keep the air vents clean and free of debris to avoid overheating the motor Clean after
13. ng cut 4 Spool worn or damaged 4 Replace spool Line pulls back 1 Too little line outside 1 Remove cover and pull 4 inches into head of head 10 cm of line outside of head 2 Line size incorrect 2 Use only 0 065 in 1 65 mm dia line LIMITED WARRANTY ELECTROLUX HOME PRODUCTS INC warrants to the original purchaser that each new Weed Eater brand electric or cordless product is free from defects in material and workmanship and agrees to repair or replace under this warranty any defective Weed Eat er brand electric product within two 2 years from the original date of purchase If your Weed Eater brand electric or cordless product should fail within the limited warranty period return it complete prepaid with proof of purchase to the dealer from whom it was purchased for repair or replacement at the op tion of ELECTROLUX HOME PRODUCTS INC This warranty is not transferable and does not cover damage or liability caused by improper handling improper maintenance or the use of accessories and or attachments not specifically recommended by ELECTROLUX HOME PRODUCTS INC forthis electric product Ad ditionally this warranty does not cover parts that will wear and require replacement with reason able use during the warranty period This war ranty does not cover predelivery set up or nor mal adjustments explained in the instruction manual THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY HAV
14. ommended remedies below except remedies that require unit to be operating TROUBLE CAUSE REMEDY Trimmer head 1 Crowding trimmer line Allow tip of line to do the cutting stops under a against material being load or does not cut turn when switch 2 Electrical failure is pressed 3 Thrown circuit breaker 4 Debris stopping head Contact your authorized service dealer Check Breaker Box Remove debris AON Line does not 1 Line improperly routed 1 Check line routing advance or in head breaks while Line improperly cutting wound into spool Incorrect line size Not enough line outside of head 2 Rewind line tightly and evenly 3 4 5 Dirt buildup on unit 1 2 3 Use only 0 065 in 1 65 mm dia line Remove cover and pull 4 inches 10 cm of line out of head Clean unit Use only 0 065 in 1 65 mm dia line Line welds onto Line size is incorrect ON 0M FO Pf spool Incorrect spool Replace with correct spool Line is being crowded Cut with tip of line fully extended against material being cut Line releases 1 Line improperly 1 Check line routing continuously routed in head 2 Spool damaged 2 Replace spool Line usage is 1 Line improperly routed 1 Check line routing excessive in head 2 Line size is incorrect 2 Replace spool 3 Crowding line against 3 Cut with tip of line fully extended material bei
15. quare within a squareJ may also be marked on the appliance Failure to have the unit repaired by qualified service person nel can cause the double insulation construc tion to become ineffective and result in seri ous injury SAVE THESE INSTRUCTIONS ASSEMBLY WARNING If received assembled review all assembly steps to ensure your unit is properly assembled and all fasteners are secure INSTALLATION OF ASSIST HANDLE 1 Place unit on a flat surface 2 Loosen and remove wing nut and bolt from assist handle 3 Firmly push the assist handle over the tube To make installation easier tilt han dle toward trigger housing while pushing down see illustration 4 Reinstall bolt in handle Thread wing nut onto bolt 5 Adjust the handle up or down the tube to a comfortable position tighten wing nut se curely Trigger Housing ATTACHING THE SHIELD A WARNING The shield must be prop erly installed The shield provides partial protection from the risk of thrown objects to the operator and others Your unit is equipped with a line limiter blade which cuts excess line to the proper length while running The line limiter blade on underside of shield is sharp and can cut you NOTE If shield is not properly installed damage to unit including motor failure will re sult 1 Align the installation arrow on the shield with the installation arrow on the motor housing see illustration below 2 Insert t
16. te nance GENERAL RECOMMENDATIONS The warranty on this unit does not cover items that have been subjected to operator abuse or negligence To receive full value from the warranty the operator must maintain unit as instructed in this manual Various adjust ments will need to be made periodically to properly maintain your unit BEFORE EACH USE CHECK FOR LOOSE FASTENERS AND PARTS e Housing Screws e Assist Handle e Debris Shield CHECK FOR DAMAGED OR WORN PARTS Contact an authorized service dealer for re placement of damaged or worn parts e Trigger Switch Ensure switch functions properly by pressing and releasing the trig ger switch Make sure motor stops e Debris Shield Discontinue use of unit if debris shield is damaged AFTER EACH USE INSPECT AND CLEAN UNIT AND LA BELS e After each use inspect complete unit for loose or damaged parts Clean the unit us ing a damp cloth with a mild detergent e Wipe off unit with a clean dry cloth SERVICE AND ADJUSTMENTS REPLACING THE LINE 1 Disconnect the unit from the power source Remove the spool by firmly pulling on the tap button Clean entire surface of hub and spool Replace with a pre wound spool or cut a length of 30 feet of 0 065 1 65 mm di ameter Weed Eater brand line Use of heavier lines could overload and damage unit A WARNING Never use wire rope string etc which can break off and become a dangerous missile PO D 11
Download Pdf Manuals
Related Search