Motorola MD207R Two-Way Radio User Manual
Contents
1. Briefly press the amp key The scan amp will appear in the display and the radio will begin to scroll through all channel and code combinations 2 When the radio detects channel activity matching the channel and code combination it stops scrolling and you can hear the transmission 3 To respond and talk to the person transmitting press within five seconds after the end of the transmission 4 The radio will resume scrolling through the channels five seconds after the end of any received activity 5 To stop scanning briefly press the y key To start Advanced Scanning 1 Set the Interference Eliminator Code to 0 2 Briefly press the amp key The scan amp will appear in the display and the radio will begin to scroll through the channels No Interference Eliminator Codes will filter what is heard 3 When the radio detects channel activity with ANY code or NO code it stops scrolling and you can hear the transmission Any Interference Eliminator Code that may be in use by that party will be detected and displayed 4 Torespond and talk to the person transmitting press within five seconds of the end of the transmission The radio will transmit using the newly detected Interference Eliminator Code 5 The radio will resume scrolling through the channels five seconds after the end of any received activity 6 To stop scanning briefly press the amp key Scanning Notes 1 If you press while the r2. Canada RF exposure guidelines If you do not use one of the Motorola supplied or approved body worn accessories and are not using the radio held in the normal use position ensure the radio and its antenna are at least 1 inch 2 5 cm from your body when transmitting Data Operation If applicable when using any data feature of the radio with or without an accessory cable position the radio and its antenna at least one inch 2 5 cm from the body Approved Accessories 53724 Remote Speaker with Push to Talk Microphone 53727 Earbud with Push to Talk Microphone 53728 Flexible Ear Receiver Electromagnetic Interference Compatibility Note Nearly every electronic device is susceptible to electromagnetic interference EMI if inadequately shielded designed or otherwise configured for electromagnetic compatibility This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Facilities To avoid electromagnetic interference and or compatibility conflicts turn off your radio in any facility where posted notices instruct you to do so Hospitals or health care facilities may be using equipment that is sensitive to external RF energy Aircraft When instructed to do so turn off your radio when onboard on aircraft Any us
3. D MOTOROLA T TALKABOLT Two Way Radio User Guide KEM ML36801 27 MD207 Series For More Information For further information you may call Motorola at 1 800 638 5119 U S or e mail us at support giantintl com or visit us on the Internet at www motorolasolutions com talkabout Safety and General Information Important Information on Safe and Efficient Operation Read This Information Before Using Your Radio The information provided in this document supersedes the general safety information in user guides published prior to December 1 2002 Transmit and Receive Procedure Your two way radio contains a transmitter and a receiver To control your exposure and ensure compliance with the general population uncontrolled environment exposure limits always adhere to the following procedure e Transmit no more than 50 of the time e To receive calls release the Push to Talk PTT button e To transmit talk press the PTT button Transmitting 50 of the time or less is important because the radio generates measurable RF energy exposure only when transmitting in terms of measuring standards compliance Exposure to Radio Frequency Energy Your Motorola two way radio complies with the following RF energy exposure standards and guidelines e United States Federal communications Commission Code of Federal Regulations 47CFR part 2 sub part J e American National Standards Institute ANSI Institute of Electrical and
4. FREQUENCIES 162 400 162 500 Wxio 161 750 162 475 162 525 WX11_ 162 000 Consumer Two Way Radio Products and Accessories purchased in the United States What Does this Warranty Cover Subject to the exclusions contained to the right Giant International Ltd warrants the Motorola branded consumer two way radios that operate via Family Radio Service or General Mobile Radio Service that it manufactures Products the Motorola branded or certified accessories sold for use with these Products that it manufactures Accessories to be free from defects in materials and workmanship under normal consumer usage for the period s outlined below This limited warranty is a consumer s exclusive remedy and applies as follows to new Motorola branded Products and Accessories manufactured by Giant International Ltd and purchased by consumers in the United States which are accompanied by this written warranty Patent and Copyright Information Manufactured distributed or sold by Giant International Ltd official licensee for this product MOTOROLA MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings LLC and are used under license All other trademarks are the property of their respective owners 2013 Motorola Solutions Inc All rights reserved Products Covered Length of Coverage One 1 year from the date of purchase by the first consumer purchaser of th
5. and remove the cover Insert the three AA alkaline batteries with and polarity as shown inside The ribbon should be underneath the AA alkaline batteries and should wrap around the right side of the batteries for easy removal 4 Reposition the battery cover and press down to secure Radio Battery Meter The radio battery icon shows the radio battery charge level from full to empty When the radio has one segment left the radio chirps periodically or after releasing E Low Battery Alert Removing the NiMH Battery Pack 1 Turn the radio off 2 With the back of the radio facing you lift the battery latch up to release the battery cover and remove the cover 3 Remove the NiMH battery pack by gently pulling the ribbon attached to the radio 4 Reposition the battery cover and press down to secure Removing the Three AA Alkaline Batteries Optional Accessory 1 Turn the radio off 2 With the back of the radio facing you lift the battery latch up to release the battery cover and remove the cover 3 Remove each alkaline battery by gently pulling the ribbon attached to the radio and easing each battery out individually 4 Reposition the battery cover and press down to secure Notes e Exercise care when removing NiMH or AA batteries Do not use sharp or conductive tools to remove either of these batteries e Remove the batteries before storing your radio for extended periods of time Batteries corrode
6. radio 3 Adjust the volume appropriately by pressing Lower the volume before placing the accessory on your head or in your ear Note The MD Series does not have VOX capabilities and is only compatible with PTT headset accessories Weather Receiver This radio can tune in to broadcasts by the United States National Oceanic and Atmospheric Administration NOAA Weather Radio You can listen to a weather channel see Weather Channels and Frequencies table for details or set the radio to alert you to emergency weather broadcasts that interrupt routine broadcasts When you listen to a weather channel you cannot use the radio in scan mode or for two way communications NOAA has transmitters located throughout the United States These transmitters broadcast watches forecasts and other information 24 hours a day Note NOAA weather radio stations are assigned to cover specific areas and service may be limited Please check with your local weather office for frequency and details or visit www weather gov nwr in the US to view the appropriate transmitter for your area The use of the NOAA logo does not provide an endorsement or implied endorsement by NOAA s National Weather Service Turning Weather Channel Reception On and Off 1 To turn weather reception on press and hold for 3 seconds 2 To turn off press and hold for 3 seconds or turn the radio off and then back on Scanning for Weather Channel The radio c
7. Electronic Engineers IEEE C95 1 1992 Institute of Electrical and Electronics Engineers IEEE C95 1 1999 Edition e International Commission on Non lonizing Radiation Protection ICNIRP 1998 Ministry of Health Canada Safety Code 6 Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 KHz to 300 GHz 1999 e Australian communications Authority Radiocommunications Electromagnetic Radiation Human Exposure Standard 2003 e ANATEL ANNEX to Resolution No 303 of July 2 2002 e ANATEL ANNEX to Resolution No 533 of September 10 2009 To ensure optimal radio performance and make sure human exposure to radio frequency electromagnetic energy is within the guidelines set forth in the above standards always adhere to the following procedures Portable Radio Operation and EME Exposure Antenna Care Use only the supplied or an approved replacement antenna Unauthorized antennas modifications or attachments could damage the radio and may violate FCC regulations Do NOT hold the antenna when the radio is IN USE Holding the antenna affects the effective range Body Worn Operation To maintain compliances with FCC Health Canada RF exposure guidelines if you wear a radio on your body when transmitting always place the radio in a Motorola supplied or approved clip holder holster case or body harness for this product Use of non Motorola approved accessories may exceed FCC Health
8. FORMATION OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS OR ACCESSORIES TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW Some states and jurisdictions do not allow the limitation or exclusion of incidental or consequential damages or limitation on the length of an implied warranty so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state or from one jurisdiction to another MD207 Series
9. Off Your radio will save power by automatically turning itself off if unused after a predetermined amount of time 1 Activate this setting by short pressing WW until displays The current setting 0 30 60 90 will flash 2 Press or to set the time to 30 minutes 60 minutes or 90 minutes 3 When you exit the Menu mode the setting timer will begin if you are not using the radio 4 The screen shows S 5 Press to confirm or 3 to exit Menu mode Special Features Keypad Lock To avoid accidentally changing your radio settings you can lock your keypad 1 Press and hold until displays 2 When in lock mode you can turn the radio on and off receive transmit send a call tone and monitor channels All other functions are locked To unlock the radio press and hold a for a few seconds until no longer displays Scanning Channels Use scan to search the 22 channels for transmissions from unknown parties to find someone in your group who has accidentally changed channels or to quickly find unused channels for your own use There are 2 modes of scanning basic and advanced to make your search more effective The Basic Scan mode uses the channel and code combinations for each of the 22 channels as you have set them The Advanced Scan mode will scan all channels for any and all codes detect any code in use and use that code value temporarily for that channel To start Scanning 1
10. Tones Your radio can transmit different call tones to other radios in your group so you can alert them that you want to talk You have 10 call tones from which to choose To set a call tone 1 With the radio on short press S until a appears The current call tone setting flashes 2 Press or to change and hear the call tone 3 Press to set the new call tone or Oto continue set up To transmit your call tone to other radios set to the same channel as your radio press J Note Setting the call to 0 disables the call tone feature Transmitting a Talk Confirmation Tone You can set your radio to transmit a unique tone when you finish transmitting It is like saying Roger or Over to let others know you are finished talking 1 With the radio on short press WW until appears The current setting On Off flashes 2 Press or to turn On or Off 3 Press to set the talk confirmation tone or Sto continue set up Keypad Tones You may enable or disable the speaker key tones You will hear the key tone each time a button is pushed 1 Press 8 until J appears The current setting On Off will flash 2 Press either or to turn On or Off 3 Press to confirm or 3 to continue set up Note When the key tone feature is off the following are not disabled e Transmit timeout alert tone e Power down alert tone e Low battery alert tone e The transmitted talk confirmation tone Auto Power
11. adio is scrolling through inactive channels the transmission will be on the home channel Scanning will resume five seconds after the end of your transmission You may press to stop scanning at any time 2 Ifthe radio stops on an undesired transmission you may immediately resume the scan by briefly pressing 3 Ifthe radio repeatedly stops on an undesired transmission you may temporarily remove that channel from the scan list by pressing and holding for three seconds You may remove more than one channel in this way 4 To restore the removed channel s to the scan list turn the radio off and then back on or exit and re enter the scanning mode by pressing 5 You cannot remove the home channel from the scan list 6 In Advanced Scan mode the detected code will only be used for one transmission You must note the code exit scan and set that detected code on that channel to permanently use the detected code Use With Accessories You can transmit more reliably with the use of optional PTT headset accessories A PTT headset allows privacy to others around you while listening Many accessories sold separately are available for your radio For more information visit our Web site at www motorolasolutions com talkabout or shop giantintl com 1 Turn the radio off and plug the PTT accessory into the accessory jack 2 Turn the radio on You may now press the PTT on the accessory microphone instead of the
12. an scan for an active NOAA transmission automatically 1 After turning Weather Reception on briefly press the key 2 The scan icon amp will appear in the display and the channel will scroll through the NOAA channels 1 7 3 When the radio detects channel activity it stops scanning and you can hear the transmission 4 You may resume the scan by briefly pressing or 5 To stop scanning briefly press The scan icon amp will disappear Setting the Weather Channel Manually If you know which frequency is correct for your location refer to the Weather Channels and Frequencies table to manually set your radio to the appropriate weather channel 1 After turning Weather Reception on press The current channel flashes 2 Press or to select the appropriate channel with good reception in your area 3 Press Cn to save the weather channel setting Setting the Weather Alert The radio can be set to respond to NOAA Weather Radio emergency messages A special alarm tone sounds an alert and turns on the weather receiver to give you immediate weather and emergency information 1 After turning Weather Reception on press twice ON or OFF flashes 2 Press or to select ON to activate If you activate the Weather Alert and return to two way mode will display 3 Press C to save the Weather Alert setting 4 Press and hold for 3 seconds to return to two way mode WEATHER CHANNELS AND
13. ccessory Jack S Call Tone Keypad Lock Volume Scroll Power Menu High Weather Volume Scroll Scan Monitor Q mororo a Low 000000000 Microphone o00 000000 Speaker Recharging Jack Display Screen Guide ii fl VOL 8 al oc Numbers for channel L Numbers for Codes Call Tone m Battery Meter TX Transmitting Keypad Lock RX Receiving ONOFF On Off for each P Auto Power On Off feature amp Weather Alert Talk Confirmation alien Tone Roger Beep Call Tone Keypad Tone VOL Volume Getting Started Installing the Batteries Each radio uses 1 NiMH rechargeable battery pack or 3 AA alkaline batteries and beeps when the batteries are low Installing NiMH Rechargeable Battery Pack 1 Turn the radio off 2 With the back of the radio facing you lift the battery latch up to release the battery cover and remove the cover 3 Remove the NiMH battery pack from the clear plastic bag do not disassemble or unwrap the battery pack 4 Insert the NiMH battery pack with the diagram facing you The ribbon should be underneath the battery pack and should wrap around the right side of the battery pack for easy removal 5 Reposition the battery cover and press down to secure Installing the Three AA Alkaline Batteries Optional Accessory Turn the radio off 2 With the back of the radio facing you lift the battery latch up to release the battery cover
14. e of a radio must be in accordance with applicable regulations per airline crew instructions Medical Devices Pacemakers The Advanced Medical Technology Association recommends that a minimum separation of 6 inches 15 cm be maintained between a handheld wireless radio and a pacemaker These recommendations are consistent with the independent research by and recommendations of the U S Food and Drug Administration People with pacemakers should e ALWAYS keep the radio more than 6 inches 15 cm from their pacemaker when the radio is turned ON e Not carry the radio in the breast pocket e Use the ear opposite the pacemaker to minimize the potential for interference e Turn the radio OFF immediately if there is any reason to suspect that interference is taking place Medical Devices Hearing Aids Some digital wireless radios may interfere with some hearing aids In the event of such interference you may want to consult your hearing aid manufacturer to discuss alternatives Medical Devices Other If you use any other personal medical device consult the manufacturer of your device to determine if it is adequately shielded from RF energy Your physician may be able to assist you in obtaining this information Safety and General Use While Driving Check the laws and regulations regarding the use of radios in the area where you drive and always obey them If you do use your radio while driving please e Give full attent
15. e product unless otherwise provided for below Products and Accessories as defined above unless otherwise provided for below Ninety 90 days from the date of purchase by the first consumer purchaser of the product Consumer Two Way Radio 1 Accessories Products and Accessories that are Repaired or Replaced The balance of the original warranty or for ninety 90 days from the date returned to the consumer whichever is longer Who is covered This warranty extends only to the first consumer purchaser and is not transferable What will GIANT INTERNATIONAL LTD do GIANT INTERNATIONAL LTD at its option will at no charge repair replace or refund the purchase price of any Products or Accessories that does not conform to this warranty We may use functionally equivalent reconditioned refurbished pre owned or new Products Accessories or parts How to Obtain Warranty Service or Other Information To obtain service or information please call USA Two Way Radios 1 800 638 5119 support giantintl com For Accessories please call the telephone number designated above for the product with which they are used You will receive instructions on how to ship the Products or Accessories at your expense to a GIANT INTERNATIONAL LTD Authorized Repair Center To obtain service you must include a a copy of your receipt bill of sale or other comparable proof of purchase b a written description of the pr
16. ess or to select a channel 3 Press Ento confirm or Oto continue set up Channels and Frequencies CACC aa omor e ee GMRS GMRS eos omens e fee COCOA e e we Selecting the Interference Eliminator Code Interference Eliminator Codes help minimize interference by blocking transmissions from unknown sources Your radio has 121 Interference Eliminator Codes Codes 1 38 are the standard analog codes that appear on other FRS GMRS radios Codes 39 121 are additional digital codes added for superior interference protection 0 is the off position no analog or digital codes are enabled GMRS GMRS GMRS GMRS GMRS GMRS To set the code for a channel 1 Press until the code starts to flash 2 Press or to select the code 3 Press to save the code setting or to continue set up You can set a different code for each channel using this procedure An extended press of or allows you to scroll through the Interference Codes rapidly so you can quickly reach the code you want Note You must set the Interference Eliminator Code to 0 on a radio that uses Interference Eliminator Codes to communicate with radios that do not have Interference Eliminator Codes Select 0 for no tone no code and OFF will flash on your radio s display r f o f e f a f a y o o e m a ss wm om D OO a a OO a a Continued on back MD207 Series Setting and Transmitting Call
17. he back of the radio Turning Your Radio On and Off 1 To turn on press and hold until a channel number appears and the radio beeps 2 To turn off press and hold until the display goes blank Setting the Volume Press to increase or to decrease the volume The volume level flashes and VOL displays Talking and Listening To communicate all radios in your group must be set to the same channel 1 To talk press and hold En 2 When you are finished talking release E For maximum clarity hold the radio two to three inches away from your mouth and speak directly into the microphone Do not cover the microphone while talking Talk Range Your radio is designed to maximize performance and improve transmission range Do not use the radios closer than five feet apart Monitor Button Pressing and holding amp for three seconds allows you to listen to the volume level of the radio when you are not receiving You can also press amp to check for activity on the current channel before you talk Push to Talk Timeout Timer To prevent accidental transmissions and save battery life the radio emits a continuous warning tone and stops transmitting if you press Cn for 60 continuous seconds Selecting the Channel Your radio has 22 channels The channel is the frequency your radio uses to transmit See Channels and Frequencies table below 1 Briefly press and release 8 The channel number flashes 2 Pr
18. ially explosive atmospheres are often but not always posted Blasting Caps and Areas To avoid possible interference with blasting operations turn off your radio when you are near electrical blasting caps in a blasting area or in areas posted Turn off two way radios Obey all signs and instructions Operational Cautions Antennas Do not use any portable radio that has a damaged antenna If a damaged antenna comes into contact with your skin a minor burn can result Batteries All batteries can cause property damage and or bodily injury such as burns if a conductive material like jewelry keys or beaded chains touch exposed terminals The conductive material may complete an electrical circuit short circuit and become quite hot Exercise care in handling any charged battery particularly when placing it inside a pocket purse or other container with metal objects Exercise care when removing NiMH or AA batteries Do not use sharp or conductive tools to remove either of these batteries Battery Charger Safety Instructions Save these Instructions 1 Do not expose the charger to rain or snow 2 Do not operate or disassemble the charger if it has received a sharp blow or has been dropped or damaged in any way 3 Never alter the AC cord or plug provided with the unit If the plug will not fit the outlet have the proper outlet installed by a qualified electrician An improper condition can result in a risk of elect
19. ion or modification in any way by someone other than Motorola Solutions Inc Giant International Ltd or its authorized service centers are excluded from coverage Altered Products Products or Accessories with a serial numbers or date tags that have been removed altered or obliterated b broken seals or that show evidence of tampering c mismatched board serial numbers or d nonconforming or non Motorola branded housings or parts are excluded from coverage Communication Services Defects damages or the failure of Products or Accessories due to any communication service or signal you may subscribe to or use with the Products or Accessories is excluded from coverage What Other Limitations Are There ANY IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY OTHERWISE THE REPAIR REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED IN NO EVENT SHALL MOTOROLA SOLUTIONS INC OR GIANT INTERNATIONAL LTD BE LIABLE WHETHER IN CONTRACT OR TORT INCLUDING NEGLIGENCE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT OR ACCESSORY OR FOR ANY INDIRECT INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR LOSS OF REVENUE OR PROFITS LOSS OF BUSINESS LOSS OF IN
20. ion to driving and to the road e Use hands free operation if available e Pull off the road and park before making or answering a call if driving conditions so require The use of a two way radio while engaged in activities requiring concentration may cause distraction or otherwise impair your ability to safely participate in such activities Always use technology safely Do not place a portable radio in the area over an air bag or in the air bag deployment area Air bags inflate with great force If a portable radio is placed in the air bag deployment area and the air bag inflates the radio may be propelled with great force and cause serious injury to occupants of the vehicle Potentially Explosive Atmospheres Turn off your radio prior to entering any area with a potentially explosive atmosphere Only radio types that are especially qualified should be used in such areas as Intrinsically Safe Do not remove install or charge batteries in such areas Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death Note The areas with potentially explosive atmospheres referred to above include fueling areas such as below decks on boats fuel or chemical transfer or storage facilities areas where the air contains chemicals or particles such as grain dust or metal powders and any other area where you would normally be advised to turn off your vehicle engine Areas with potent
21. oblem c the name of your service provider if applicable d the name and location of the installation facility if applicable and most importantly e your address and telephone number Exclusions Normal Wear and Tear Periodic maintenance repair and replacement of parts due to normal wear and tear are excluded from coverage Batteries Only batteries whose fully charged capacity falls below 80 of their rated capacity and batteries that leak are covered by this limited warranty Abuse amp Misuse Defects or damage that result from a improper operation storage misuse or abuse accident or neglect such as physical damage cracks scratches etc to the surface of the product resulting from misuse b contact with liquid water rain extreme humidity or heavy perspiration sand dirt or the like extreme heat or food c use of the Products or Accessories for commercial purposes or subjecting the Product or Accessory to abnormal usage or conditions or d other acts which are not the fault of Motorola Solutions Inc or Giant International Ltd are excluded from coverage Use of Non Motorola branded Products and Accessories Defects or damage that result from the use of Non Motorola branded or certified Products Accessories or other peripheral equipment are excluded from coverage Unauthorized Service or Modification Defects or damages resulting from service testing adjustment installation maintenance alterat
22. over time and may cause permanent damage to your radio Using the Plug in Charging Adaptor The battery plug in charger adaptor provides charging convenience for NiMH batteries in one or both radios Charge the NiMH battery overnight at least 16 hours before using it for the first time After the initial charge an empty battery is fully charged within 14 hours 1 Follow the steps above to install a NiMH battery pack 2 Connect the AC power adaptor plug into the recharging jack at the bottom of the radio The adaptor charges two radios 3 Plug the AC power supply into a standard wall outlet Notes e The battery icon will scroll while the battery pack is being charged e When moving between hot and cold temperatures do not charge the battery until the battery temperature acclimates usually about 20 minutes e For optimal battery life unplug the charging adaptor within 16 hours Do not store the radio while connected to the charger Low Battery Alert In addition to your battery meter showing how much battery power you have your radio will beep to alert you to the fact that your batteries are low Attaching and Removing the Belt Clip 1 Attach belt clip to pocket or belt strap 2 Align the belt clip post with the hole in the back of the radio 3 Gently push until the clip clicks in place To Remove 1 Push down on the release tab at the top of the belt clip to release the catch 2 Pull the belt clip away from t
23. ric shock 4 To reduce the risk of damage to the cord or plug pull the plug rather than the cord when disconnecting the charger from the AC receptacle 5 To reduce the risk of electric shock unplug the charger from the outlet before attempting any maintenance or cleaning 6 Use of an attachment not recommended or sold by Motorola may result in a risk of fire electric shock or personal injury 7 Make sure the cord is located so it will not be stepped on tripped over or subjected to damage or stress 8 An extension cord should not be used unless absolutely necessary Use of an improper extension cord could result in a risk of a fire and or electric shock If an extension cord must be used make sure that e The pins on the plug of the extension cord are the same number size and shape as those on the plug of the charger e The extension cord is properly wired and in good electrical condition e The extension cord size is 18 AWG for lengths up to 100 feet and 16 AWG for lengths up to 150 feet 9 The supply cord of the AC adaptor cannot be replaced If the cord is damaged call customer service at 1 800 638 5119 or e mail us at support giantintl com FCC Licensing Information Your Motorola radio operates on General Mobile Radio Service GMRS frequencies and is subject to the Rules and Regulations of the Federal Communications Commission FCC The FCC requires that all operators using GMRS frequencies obtain a radio licen
24. se before operating their equipment To obtain the FCC forms please visit the FCC s Web site at wireless fcc gov uls index htm job home to source form 605 and 159 which includes all the instructions you will need If you wish to have the document faxed or mailed or if you have questions please use the following contact information For mail service Call the FCC Forms Hotline For a fax Contact the If you have questions about Fax 0n Demand the FCC License system Call the FCC 1 202 418 0177 1 800 418 FORM 1 888 CALL FCC 3676 225 5322 Changes or modifications not expressly approved by Motorola may void the user s authority granted by the FCC to operate this radio and should not be made To comply with FCC requirements transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services Replacement of any transmitter component crystal semiconductor etc not authorized by the FCC equipment authorization for this radio could violate FCC rules You can find the label with the FCC ID in the battery compartment Note Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited Control Buttons en Push to talk A
Download Pdf Manuals
Related Search