Home
Miele T 8822 C Clothes Dryer User Manual
Contents
1. Minimum iron fabrics tend to crease more the larger the load This is also the case for garments made from very fine weave fabrics such as shirts or blouses If in doubt divide the garments into smaller loads Starched laundry can be dried in the tumble dryer To achieve the usual finish double the amount of starch should be used New dark coloured garments should be washed and dried separately from light coloured garments to avoid the danger of colours running and discolouring other garments or even plastic components in the dryer Dark coloured fibres can also settle on light coloured garments and vice versa How to dry correctly Brief instructions The headings numbered 0 show the operating sequence and can be used as a brief guide to using your dryer Sort the laundry To ensure an even drying result separate out the washed laundry and sort it according to the drying level required the type of fibre or weave size the moisture content after spinning N Make sure that objects e g detergent dispensing balls have been removed from the laundry They could melt and cause damage to the dryer or the laundry Check seams and stitching to ensure that padding and linings are intact Fasten duvet covers and pillow cases to prevent small items from being trapped inside them Fasten hooks and eyes etc Tie fabric belts and apron strings Sew in or
2. Air inlet vent for cooling the condenser unit 3 Mains connection cable 9 Hose for external drainage of condensed water Accessories for connection to a sink drain outlet Installation site N Make sure the dryer door can be opened without hindrance after installation Transporting the dryer to its installation site When moving the dryer hold it by the lid where it protrudes to the rear To manoeuvre the dryer out of its packing case to its installation site you will also need to hold it by the front feet Building under a continous worktop in a kitchen run NA building under kit with a coverplate to replace the appliance lid is required It must be fitted by a suitably qualified person to ensure electrical safety N B If you wish to push your appliance under a worktop and there is space to do this without removing the lid the building under kit is not necessary Otherwise it is essential The building under kit is supplied with its own installation instructions N B When built under drying times may be longer The electrical socket must be located in an accessible position near the appliance With niche heights of 830 840 mm longer screw feet are required 870 885 915 930 mm one or two raising kits are required Miele accessory available to order Replacing the lid If the lid has been removed in order to fit a coverplate ensure that if the lid is
3. Problem solving guide 28 Check and fault messages 28 An unsatisfactory drying result 31 Other problems 32 Changing the lamp saa si a ce eed ada e bbe bb obeae Redes PES Ree 34 After Sales service 35 FROGS Saat ate ae trae sk cde Attn ana aeons kaag te eg eens Bn ten aa eens 35 Future Updates PC 4 000050 ag AA bi gind Ba a a Gere ae eed haa 35 Appliance Quarant6 IIIA niio ete Ne dee baie 35 Optional ACCESSONES i264 ie hha edad bi ESE bebe ee he dees 35 Installation 36 FrOMt WISMA non vb ool JA ae ap a ge KENE pe Phere dae be eee daw baw ates 36 REG WIOWS ee nahh On ee a RG yaad Ba ea ee Gls hed eae BO a ee WS Oe eh dled 37 NASA AND SNG aa ag ate ge Nee eee ae Cada bed be ead KE Ag kaa 37 Transporting the dryer to its installation site 37 Building under a continous worktop in a kitchen run 37 Levelling the appliance is kaa eee 38 NGONO A ON s s aaa ak none Gate ww ne dea ee a WA ee Ga ee a 38 Washer dryerStaCkyiii entiac tesa enis ni bA ke ERAN E aa Ra ga a ok 38 Before moving the tumble dryer again e g when moving house 38 External condensed water outlet saa aia a oddati eee 39 Arranging the drain NOSE 02
4. Reduced temperature Select Low temperature for delicate textiles ie Do not tumble dry lroning A Very hot A Hot A Warm a Do not iron Tips on drying Always observe the maximum recommended loads given in the Programme chart Never overload the drum Overloading can cause unnecessary wear and tear to the laundry give a disappointing drying result and cause more creasing Do not put soaking wet items into the tumble dryer Spin fabrics for at least 30 seconds before drying Open jackets so that they can dry evenly Use the Automatic plus programme for drying mixed loads of cotton and minimum iron fabrics Woollens and wool blends tend to become matted and shrink if dried in a tumble dryer They can however be fluffed up using the Woollens handcare programme Down filled garments have linings which have a tendency to shrink depending on the quality of the item They can be partially dried using the Gentle smoothing programme Pure linen should only be machine dried if specified as suitable by the manufacturer on the care label as the surface of the fabric may otherwise become rough Loopknit garments e g T shirts and underwear tend to shrink depending on their quality Do not over dry these textiles When purchasing these garments it is advisable to take their shrinkage properties into account
5. The number which appears alternately in the display with P means O Default setting i The cooling down time will be five minutes longer The Automatic plus indicator light will also flash once 2 The cooling down time will be ten minutes longer The Automatic plus indicator light will also flash twice Pressing the Start Stop button switches from one number to another Switch the dryer off with the 1 button The setting you have selected is now stored in memory You can change it again at any time 49 Programmable functions Clean out airways indicator Fluff should be removed after drying The Clean out airways indicator will remind you to clean the filters when a certain amount of fluff has collected in the filters You can decide at what level of fluff this reminder should be given You will have an idea of which of the four options to select after a few drying programmes Follow steps to to programme and store in memory Before you begin first ensure that The tumble dryer is switched off The door is closed 50 Press the Start Stop button and keep it pressed in whilst carrying out steps 0 9 Press the LA button in Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button five times The Low temperature indicator light will flash on an
6. your Miele dealer or the Miele Service Department see back cover for contact details When contacting your dealer or the Service Department please quote the model and serial number of your appliance both of which are shown on the data plate situated on the right hand side below the drum aperture N B A call out charge will be applied for service visits where the problem could have been rectified as described in these instructions Future updates PC The indicator or check light marked PC on the fascia panel is the interface used by the Miele service technicians during service work for testing purposes and for updating the appliance s programme data Appliance guarantee Please see the guarantee card supplied with your appliance Optional accessories Optional accessories for this dryer are available from your Miele Dealer the Miele Spare Parts Department or via the internet at www miele shop com Please note that telephone calls may be monitored and recorded for training purposes 35 Installation Front view Mains connection cable 2 Condensed water container 3 Control panel Door 36 Service panel for condenser unit Four height adjustable screw feet External drainage options e g via wash basin wash basin drain outlet or gully Installation Rear view Protruding lid for holding when moving the dryer see arrows
7. Select the Low temperature option for delicate fabrics with the O symbol on the care label Cool air Max load 7 kg Fabric type Any item which only needs airing Warm air Max load 7 kg Fabric type Voluminous and multi layered fabrics whose layers have different drying characteristics e g jackets pillows For drying individual items e g bath towels swimwear tea towels Note Do not select the longest drying time to start with Check the items as you are drying them to find the optimum time Low temperature Select the Low temperature option for delicate fabrics with the O symbol on the care label Note You can use the Warm air programme to help remove odours from clean cotton clothing select a duration of between 1 2 and 1 hour Items must be suitable for drying in a tumble dryer Dampen the garments a little beforehand or add a fabric conditioner sheet Odours will not be removed as effectively from any parts of the garments which are made of synthetic fibres Gentle smoothing Max load 1 kg Fabric type Cotton and linen fabrics Minimum iron items made of mixed fibres cottons or synthetics e g trousers anoraks shirts Notes Smoocths out creasing caused during the spin cycle in the washing machine Remove garments as soon as the programme has finished so that they are easy to iron Weight of dry laundry 18 Changing the programme se
8. 1200 40 1 40 45 Minimum iron Normal Low temperature 3 5 1200 40 1 50 73 Minimum iron Hand iron 35 1200 40 1 20 39 Automatic plus Normal 5 0 800 50 2 70 114 Shirts Normal 2 0 600 60 1 40 59 Delicates Normal 2 5 700 50 1 55 116 Proofing Normal 2 9 800 50 1 85 96 Denim Normal 3 0 900 60 2 40 119 Express Normal 3 5 1000 60 2 20 69 Gentle smoothing 1 0 1000 60 0 75 32 Woollens handcare 2 0 1000 50 0 15 4 4 Weight of dry laundry 2 EN 61121 2005 test programme All data was calculated using EN 61121 2005 unless otherwise stated Notes for test institutes Before testing in accordance with EN 61121 dry a3 kg load of cotton laundry with 70 residual moisture as per the above standard using the Cottons Normal programme without any extra options Consumption data can vary from the nominal values given above depending on the size of the load types of textiles residual moisture levels after spinning fluctuations in the electricity supply and any extra options selected 43 Technical data Height Width Depth Depth with door open Height for building under Width for building under Depth for building under Suitable for pushing under a worktop Suitable for stacking Weight Drum volume Maximum capacity Capacity of condensed water container Drain hose length Maximum delivery head Maximum drain hose length Length of connection cable Voltage Connected load Fuse rating Lamp wattag
9. 4s00ee eine sha ee wags eae eee eae em ee eee 39 External drainage via a sink or gully 0 0 ee 40 Installation conditions requiring a non return valve ee 40 Electrical connection II IA III aaa aa 42 Electrical connection IA ee 42 Consumptiondata 43 Technical dala IIIA 44 Programmablefunctions 45 Extending the range of the drying levels 45 Amtkerease Selling 2 00 road errer tan de nad nie de eid ben ae Ot 46 Altering the volume of the buzzer 47 Memory IUNGUON 4 034 aaa ek a dae bd edad abl AA 48 Extending the cooling downtime 0 ee 49 Clean out airways indicator 50 ICV ACTON GEBANG AAA 51 Adjusting the dryer s electronics for very soft water 52 Warning and Safety instructions P It is essential to read these instructions This tumble dryer conforms to current safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the tumble dryer please read these instructions carefully before using it for the first time They contain important information on its safety installation use and maintenance Keep these instructions in a safe place and ensure that new users are familiar with th
10. Seabed ho adn opt se ete Acoma dot 15 Programmechart 16 Changing the programme sequence 19 Once a programme has started 19 CHANGING The PIO MM 40 i802 Ps bw dda ttn de ee a ee 19 cancelling the programme and then selecting a different programme 19 cancelling the programme and then removing the laundry 19 Altering Delay Stait o aad we sat aaa aed nate Ole waw Nn eek Wey ae ea 19 Adding or removing laundry after a programme has started 19 TMS reman GEN NG aa een eae ds sth ated ated aie Ragan MAM here NK IN 19 Electronic system lock 20 Cleaning and care 21 Emptying the condensed water container 0 0 0 cee 21 Cleaning the fluff filters 22 Cleaning them whilst dry ka gagi ai aaa BK a eee 22 Cleaning them with water 23 Cleaning the tumble dryer 24 Cleaning the condenser unit 25 Removing the condenser UNI IIIA 25 Checking the condenserUnit 26 Cleaning the condenser unit 26 Replacing the condenser Unit cesses wean Goan how Enea a a ew 8 27 Contents
11. alternately in the display with P means O Default setting 1 Drying level range extended The Automatic plus indicator light will also flash Pressing the Start Stop button switches from one to the other Switch the dryer off with the L button The setting you have selected is now stored in memory You can change it again at any time To select the extended drying level m Select a programme m Press the drying level button repeatedly until one or two indicator lights come on Indicator lights Extra dry and Normal Normal Indicator lights Normal and Hand iron Hand iron Indicator lights Hand iron and Machine iron Machine iron 45 Programmable functions Anti crease setting Anti crease helps prevent creasing if laundry is not normally removed immediately after the end of a programme After the programme has finished the drum will continue to rotate at intervals for 2 hours factory default setting 1 hour It is a good idea to leave the anti crease function activated to help prevent creasing for when it is not possible to remove laundry immediately after the end of the programme Follow steps to to programme and store in memory Before you begin first ensure that The tumble dryer is switched off The door is closed 46 Press the Start Stop button and keep it pressed in whilst carrying out steps 0 9 Press the L but
12. as described previously At step the indicator light for the Low temperature button will stop flashing and the key symbol G o will go out The electronics are no longer locked Cleaning and care Emptying the condensed water container The condensed water will be collected in the condensed water container unless the dryer has been connected for external drainage see Installation Empty the condensed water container after every drying programme The Empty container indicator will light up if the maximum level of the m Empty the container condensed water container is reached The indicator light will go out when the door is opened and closed again m Replace the container in the dryer N Condensed water should not be consumed It could lead to health problems for people and animals Condensed water can be put to household use e g in a steam iron or humidifier To ensure that any residual particles of fluff in the condensed water are removed before use pass it through a fine sieve or paper filter first m Pull out the condensed water container m To prevent water running out hold it at the front and towards the back and keep it in a horizontal position when carrying it 21 Cleaning and care Cleaning the fluff filters The fluff which is created by the drying process is collected by the fluff filters in the door and the door opening Clean the filters after each drying pro
13. dryer 27 Problem solving guide With the help of the following notes minor faults in the performance of the appliance some of which may result from incorrect operation can be put right without contacting the Service Department Repair work to electrical appliances should only be carried out by a suitably qualified person in strict accordance with current local and national safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work Check and fault messages Problem Possible cause Remedy The programme stops and and Finish appear in the display The buzzer sounds This is not a fault The electronic unit has recognised that there is no laundry in the drum and cancelled the programme Drying individual garments or items which are already dry can also cause the programme to be cancelled Use the Warm air programme timed drying to dry individual items To select anew programme switch the dryer off and on or Open the door place more laundry in the drum then close the door The Low temperature indicator light starts flashing after the dryer has been switched on and l o appears in the display The electronic system lock is activated You will need to deactivate the system lock before the dryer can be used see Electronic system lock The programme stops and
14. off its connection see arrow m Allow any residual water to run into the container m Unwind the hose and pull it carefully out of the holders m Position the hose to the right or left hand side as necessary Leave the hose in the middle holder to prevent it from becoming kinked inadvertently 39 Installation External drainage via a sink or gully Example Connection to a sink drain outlet m See Front view illustration The drain hose with non return valve A If you want to drain the water off fitted can be connected directly to a into a sink you will need to secure suitable sink drain outlet the hose carefully e g by tying it to a tap to make sure it cannot slip during use Otherwise there is a risk of overflowing water which could cause damage m Use the bow shaped guide to prevent the drain hose from becoming kinked Installation conditions requiring a non return valve Certain installation conditions require the fitting of a non return m Remove the following from the back valve for external water of the dryer at the top connection available as an Adapter 1 and hose clip 3 behind it optional accessory A non return valve will prevent the risk of back flow out of the dryer which could cause damage A non return valve is required If the tumble dryer is connected to a sink drain outlet see the following section If the tumble dryer is connected to a drainage syst
15. once the delay start time has a elapsed Programmable functions Default settings can be altered to adapt the dryer to different requirements See Programmable functions at the end of this booklet for more details 10 Perfect Dry indicator After a programme has started the electronics will estimate the duration of the programme time remaining The Perfect Dry indicator will flash while this is happening After a short while the programme duration will appear in the display and the indicator will go out The Perfect Dry indicator will light up again when the selected drying level is reached and remain on until the programme is finished Programme duration Estimated time remaining The estimated duration time remaining will appear in the display The following factors all affect the estimated time remaining residual moisture content after spinning type of fabric size of load room temperature fluctuations in power supply The electronics continually assess conditions in the appliance and adjust the estimated time remaining for a more accurate reading Because of this the time displayed can alter during the course of a programme Programmes can also finish earlier than expected if for example particularly fine fabrics are being dried the load is very small or items were partially dry beforehand Notes on laundry care Garment care label symbols Drying Normal higher temperature
16. remove underwiring from bras Turn on the tumble dryer m Switch the dryer on by pressing the A button in The tumble dryer may be switched on after loading saving energy as the light will not come on 12 Load the tumble dryer m Press the Door button to open the door m Load the laundry loosely into the drum Do not overload the drum See the Programme chart for recommended loads for each programme Overloading can cause unnecessary wear and tear to the laundry and give a disappointing drying result m Before closing the door make sure the fluff filter is correctly positioned Check the laundry is right inside the drum so that it cannot get trapped or damaged when the door is shut m Shut the door either with a gentle swing or lean against it and push it shut How to dry correctly 0 Select a programme O Cottons Automatic plus O O Minimum iron Denim O Shirts O Timed drying o cool air Timed drying warm air O Delicates Woollens handcare O Proofing O Express Gentle smoothing O m Select the programme you want The indicator for the programme selected will light up A drying level or extra option indicator may also light up and the duration may also be displayed Drying level programmes Cottons Minimum iron Delicates Proofing Express Automatic plus Denim Shirts Gentle smoothing Extra dry O Normal O Hand iron O Machine iron
17. the symbol on the care label Hand iron Machine iron Fabric type Cottons or linen fabrics e g table linen bed linen starched laundry Note To prevent laundry from drying out it should be rolled up until you are ready for ironing Low temperature Select the Low temperature option for delicate fabrics with the symbol on the care label Minimum iron Max load 3 5 kg Extra dry Normal Hand iron Fabric type Minimum iron items made of cotton synthetic or blended fabrics e g dresses trousers skirts and table cloths Low temperature Select the Low temperature option for delicate fabrics with the symbol on the care label Delicates Max load 2 5 kg Normal Hand iron Fabric type Delicate items made of synthetic fibres easy care cotton or blended fabrics e g shirts blouses lingerie and appliqu d garments Low temperature Low temperature cannot be deselected Weight of dry laundry Note for test insti tutes Use this programme without selecting Low temperature for testing according to Standard EN 61121 16 Programme chart Woollens handcare Max load 2 kg Fabric type Woollen fabrics Notes This programme only fluffs up woollen garments They are not dried completely by this programme Remove garments as soon as the programme has finished and leave to finish dry
18. the fluff filters and block the condenser unit Dust from the room in which the dryer is installed can also get into the condenser unit and cause a blockage Check the condenser unit at least twice a year Always check it if the Clean out airways indicator light comes on If the dryer is used frequently then check the condenser gg Turn the lever on the inner cover unit after approx 100 drying cycles downwards to the vertical position Clean it if necessary m Tilt the cover forwards Removing the condenser unit m Remove it by pulling it diagonally upwards m Open the service panel Hold the m Turn the lever on the condenser unit panel securely when doing this upwards to the vertical position so that the hook on the lever is no longer in the groove at the bottom of the condenser unit housing m Now remove the panel by pulling it diagonally upwards and place it to one side 25 Cleaning and care m Pull the condenser unit out of its housing by the handle Checking the condenser unit m Hold the condenser unit up to the light as shown m Check to see if there is any fluff inside it The arrows in the illustration above indicate where to look 26 If you cannot see any fluff m Replace the condenser unit see following page If you can see some fluff m Clean the condenser unit as described below Cleaning the condenser u
19. Cooling down or Finish flashes in the display The buzzer sounds No obvious cause Switch the dryer off and then on again Then start the programme again If the programme stops again and Cooling down or Finish flashes again there is a fault Contact the Miele Service Department 28 Problem solving guide Problem Possible cause Remedy The Clean out airways indicator light comes on This indicator light comes on to warn you that the dryer is not working efficiently Possible cause the fluff filters are clogged with fluff or with detergent residues Cleaning the fluff filters is usually all that is required However if the Clean out airways indicator light does not go out after you have cleaned the filters then also check all the possible causes described under The drying process goes on too long or even switches off To switch off the indicator light Open and close the door The Clean out airways indicator light can be deactivated see Programmable functions The programme stops The Clean out airways indicator light comes on The buzzer sounds See above for possible causes and their remedies To switch off the indicator light Open and close the door Then start the programme again If the Clean out airways indicator light comes on again contact the Miele Service Dept The Empty container indicator light comes
20. HONEYCOMB CARE os Operating instructions for condenser tumble dryer T 8822 C To avoid the risk of accidents en GB or damage to the appliance it is essential to read these instructions before it is installed and used for the first time M Nr 07 483 560 Caring for the environment Disposal of the packing Energy saving tips material To avoid unnecessarily long drying The transport and protective packing times and high consumption of energy has been selected from materials which _ Make sure that your laundry is are environmentally friendly for disposal thoroughly spun before drying and can normally be recycled Thehigher the spin the greater the Ensure that any plastic wrappings savings that can be made in energy bags etc are disposed of safely and and time during drying kept out of the reach of babies and young children Danger of suffocation Load according to the optimum amount of laundry recommended for Rather than just throwing these the programme being used see materials away please ensure they are Programme chart offered for recycling Underloading is uneconomical Overloading gives a poorer quality of drying and may cause unnecessary Electrical and electronic appliances creasing often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment Make sure the fluff filters are clean They are however e
21. Hong Kong Miele Hong Kong Limited AIA Plaza 24 Floor 18 Hysan Avenue Causeway Bay Tel 852 2610 1331 Fax 852 2610 1013 E mail mielehk miele com hk nternet www miele hk Ireland lele Ireland Ltd Broomhill Road Tallaght Dublin 24 Tel 01 461 0710 Fax 01 461 07 97 E Mail info miele ie nternet www miele ie New Zealand Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland NZ Tel 0800 264 353 Fax 0800 463 453 Internet www miele co nz South Africa Miele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 27 0 11 548 1900 Fax 27 0 11 548 1935 E mail info miele co za Internet www miele co za Singapore Miele Southeast Asia Miele Pte Ltd 163 Penang Road 04 02 03 Winsland House Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail infosea miele com sg Internet www miele sg United Arab Emirates Miele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae Internet www miele ae Alteration rights reserved 1409 CE M Nr 07 483 560 00
22. O C m Press the drying level button repeatedly until the indicator for the drying level you want lights up for almost all programmes Any of the four drying levels can be selected for the Cottons and Express programmes A more limited range is available when using other programmes and only the Normal drying level is available for the Proofing and Gentle smoothing programmes Note You can extend the range of the drying levels for some programmes see Programmable functions Woollens handcare This programme cannot be changed Selecting the duration of the timed drying Cool airand Warm air programmes The indicator light for the Delay start button will flash when the Cool air or Warm air programme is selected m Press the Delay start button repeatedly until the required duration shows in the display You can select the duration in stages for Cool air from 28 minutes up to 7 82 hour Warm air from 75 minutes up to 2 08 hours Select any Extra options Delay start m Low temperature Buzzer and Delay start are selected by pressing the appropriate button see Extra options Delay start Anti crease see next page is permanently switched on N B It is not possible to select Delay start when using the Warm air or Cool air programmes How to dry correctly Start the programme The Start Stop button will flash when a programme is being selected The flashing in
23. a to run the Warm air programme for approximately 1 minute before moving it Any remaining condensed water will then be fed into the condensed water container or out through the drain hose Installation External condensed water outlet General notes When drying is in progress condensed water is pumped into the condensed er container through the drain hose at wa the back of the dryer The condensed water can also be drained off directly if the tumble dryer is installed near a sink drain outlet etc so that the condensed water container does not have to be emptied Drain hose length 1 50 m Maximum delivery head 1 50 m Maximum drain hose length 4 00 m AN If the on site water drainage system is not fitted with a non return valve or an appropriate air gap one must be fitted to prevent the risk of back flow See Installation conditions requiring a non return valve The following optional accessories are available an extension hose a non return valve kit for connection to an external condensed water outlet includes an extension hose Maximum delivery head with non return valve fitted 1 00 m Arranging the drain hose N Do not pull on the drain hose and do not stretch it or allow it to become kinked as it could get damaged m There will be a small amount of residual water in the drain hose Have a container ready to collect this m Pull the hose
24. activated if wished The dryer s electronics are then locked The dryer can still be switched on but a programme cannot be started If an attempt is made to start a programme the indicator light for the Low temperature button will come on and a key symbol o will appear in the display The door is not locked and can be opened at any time To activate the lock Before you begin first ensure that The tumble dryer is switched off The door is closed Press the Low temperature button and keep it pressed in whilst carrying out steps to 9 Press the On 0 Off button in The Automatic plus indicator light will come on Slowly turn the programme selector three positions stage by stage ina clockwise direction Each of the three programme indicator lights must come on one after the other 20 Now slowly turn the programme selector six positions stage by stage in an anti clockwise direction Each of the six programme indicator lights must come on one after the other The indicator light for the Low temperature button will flash and a key symbol f o will appear in the display Release the Low temperature button The electronics have now been locked m Switch the dryer off To deactivate the lock Before you begin first ensure that The tumble dryer is switched off The door is closed m The procedure is the same as for activating the lock Carry out steps 9 to
25. avoid the hose slipping and the water causing damage PD Condensed water is not drinking water It can cause health problems in both people and animals PD Always keep the area around the tumble dryer free of dust and fluff Dust drawn into the tumble dryer can cause blockages in the condenser unit over time gt Do not let anyone sit or lean on the door as this can cause the tumble dryer to tip up PD Always close the door after use This way you will avoid the danger of children climbing onto or into the dryer or hiding things in it pets or other small animals climbing into it P gt The tumble dryer must not be hosed down Accessories P gt Only use genuine Miele spare parts and accessories with this appliance If non Miele parts are used guarantee performance and product liability claims may be invalidated Miele cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Operating the tumble dryer Control panel Extra dry O Drying Cool air Oo Normal Finish Co Pertect Dry Hand iron O Machine ironO CC O Cottons Automatic plus O O Minimum iron Denim O O Delicates Shirts O Delay start Buzzer Low temperature O Clean out airwayj O Empty container o Woollens Timed drying o handcare cool air I D 7 Timed drying a O Proofing Waren aie fe O Express Gentle s
26. d off once slowly P and default setting will flash alternately in the display The number which appears alternately in the display with P means O the Clean out airways indicator light is deactivated 1 the Clean out airways indicator light will come on when there is a heavy build up of fluff The Automatic plus indicator light will also flash once Cc Default setting the Automatic plus indicator light will also flash twice 3 the Clean out airways indicator light will come on when there is only a light build up of fluff The Automatic plus indicator light will also flash three times Pressing the Start Stop button switches from one number to another Switch the dryer off with the 1 button The setting you have selected is now stored in memory You can change it again at any time Programmable functions Keypad tone An audible tone sounds each time a button is pressed Follow steps to to programme and store in memory Before you begin first ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 6 86 Press the L button in Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button six times The Low temperature indicator light will flash on and off slow
27. damage Do not install or use a damaged tumble dryer gt gt Before connecting the tumble dryer ensure that the connection data on the data plate voltage and connected load match the mains electricity supply If in any doubt consult a qualified electrician P The electrical safety of this tumble dryer can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and regularly tested and where there is any doubt the household wiring system should be inspected by a qualified electrician Miele cannot be held liable for the consequences of an inadequate earthing system e g electric shock P Do not connect the tumble dryer to the mains electricity supply by an extension lead Extension leads do not guarantee the required safety of the tumble dryer e g danger of overheating gt Unauthorised repairs could result in unforeseen dangers for the user for which Miele cannot accept liability Repairs should only be undertaken by a Miele approved service technician Ensure current is not supplied to the tumble dryer until after maintenance or repair work has been carried out 6 PD Faulty components must only be replaced by genuine Miele original spare parts Only when these parts are fitted can the safety standards of the tumble dryer be guaranteed g
28. dicates that a programme can be started m Press the Start Stop button The Start Stop button will now light up constantly Drying will appear in the display and the Perfect Dry indicator will flash The indicator will go out after approx 1 minute and the estimated programme duration will appear in the display Note The duration shown in the display is an estimate and can vary Before the end of a programme The Perfect Dry indicator will light up There is a cooling down phase at the end of the drying sequence Cooling down will appear in the display The programme will not finish until the cooling down phase has been completed There is no cooling down phase at the end of the Woollens handcare programme Only with programmes with drying levels exception Gentle smoothing 14 Remove the laundry when the programme has finished 0 and Finish will appear in the display to indicate that the programme has finished The buzzer if selected will sound at intervals The drum will continue to rotate at intervals for up to two hours to prevent laundry creasing if you do not wish to remove it immediately anti crease There is no anti crease phase at the end of the Woollens handcare programme m Press the Door button m Open the door m Remove the laundry Check that all items have been removed from the drum If items are left in the dryer they could be damaged by overdrying when the dryer is
29. e Test certificates awarded Energy consumption 44 850 mm 595 mm 587 mm 1060 mm 820 mm 600 mm 600 mm yes yes 51 kg Wl 7 kg dry weight approx 4 2 1 5m 1 i 4m 2m see data plate see Consumption data Programmable functions Extending the range of the drying levels You can extend the range of the drying levels for many of the programmes Machine iron drier than Machine iron Hand iron drier than Hand iron Normal drier than Normal In addition the Extra dry drying level can be made available for the Delicates and Denim programmes You can use this programmable function to extend the range of the drying levels for the following programmes Cottons Minimum iron Delicates Automatic plus Denim Express Machine iron cannot be programmed for the Minimum iron programme Follow steps to to programme and store in memory Before you begin first ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 6 6 Press the 1 amp button in Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button The Low temperature indicator light will briefly flash on and off twice P and 8 default setting will flash alternately in the display The number which appears
30. e after installation For extra safety it is advisable to install a suitable residual current device RCD Contact a qualified electrician for advice Do not connect via an extension lead Extension leads do not guarantee the required safety of the appliance e g danger of overheating 42 Non rewireable plugs BS 1363 The fuse cover must be refitted when changing the fuse and if the fuse cover is lost the plug must not be used until a suitable replacement is obtained The colour of the correct replacement cover is that of the coloured insert in the base of the plug or the colour that is embossed in words on the base of the plug as applicable to the design of plug fitted Replacement fuses should be ASTA approved to BS 1362 and have the correct rating Replacement fuses and fuse covers may be purchased from your local electrical supplier WARNING THIS APPLIANCE MUST BE EARTHED Consumption data Load Final spin speed Residual Energy Duration in a domestic washing moisture machine kg rpm kWh Minutes Cottons Normal 7 0 1000 60 SO i Cottons Normal 7 0 1200 53 3 55 101 7 0 1400 50 3 35 97 7 0 1600 48 3 25 93 7 0 1800 43 2 90 85 Cottons Normal Low temperature 7 0 1000 60 4 20 175 Cottons Hand iron 7 0 1000 60 3 10 89 Cottons Hand iron 7 0 1200 53 2 75 79 7 0 1400 50 2 55 74 7 0 1600 48 2 45 71 7 0 1800 43 2 10 63 Minimum iron Normal gi
31. e content Pass them on to any future owner Correct application P gt This tumble dryer is for domestic use only and can only be used to dry items which have been washed in a water solution and which are marked on the manufacturer s care label as being suitable for tumble drying Dry cleaning kits for freshening up garments in a tumble dryer are increasingly available on the market If using do so at your own risk and follow the instructions provided on the packaging Any other applications may be dangerous Miele cannot be held liable for damage resulting from incorrect or improper use or operation gt This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge unless they are supervised whilst using it or have been shown how to use it by a person responsible for their safety Safety with children gt Keep children away from the tumble dryer at all times It is not a toy To avoid the risk of injury do not allow them to play on or near it or to play with its controls Supervise children whilst you are using it gt Older children may only use it if its operation has been clearly explained to them and they are able to use it safely recognising the dangers of incorrect use Warning and Safety instructions Technical safety gt gt Before setting up the tumble dryer check it for any externally visible
32. em already in use by another appliance e g a dishwasher or washing machine 40 Installation 1 Adapter 2 Nut 3 Hose clip 4 End of the hose 5 Non return valve 6 Tumble dryer drain hose m Fit adapter 1 to the sink drain outlet using nut 2 If this nut has a flat disc in it you should take the disc out first m Attach the end of hose 4 to adapter 1 m Use a screwdriver to tighten hose clip 3 up close to the nut N Non return valve 5 has to be fitted with the arrow pointing in the direction of flow i e towards the sink Otherwise water will not drain out of the appliance m Fit non return valve 5 to tumble dryer drain hose 6 make sure it is fitted in the correct direction see arrow on non return valve m Secure the non return valve using hose clips 41 Electrical connection Electrical connection U K All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current national and local safety regulations BS 7671 in the UK Ensure power is not supplied to the appliance until after installation work has been carried out The appliance is supplied with a mains cable with moulded plug ready for connection to a 230 240V mains supply Please ensure the connection data quoted on the data plate match the household mains supply Connection should be made via a suitable switched socket which is easily accessibl
33. en thoroughly cleaned there is a danger that these might ignite when heated even after they have been removed from the dryer at the end of the programme items e g mops and floorheads which have been treated with inflamable cleaning agents or contain residues of acetone alcohol benzine petrol stain remover turpentine wax wax remover or other chemicals items which have been splashed with hair lacquer hair spray nail varnish remover or similar substances When washing such heavily soiled items ensure that you use sufficient detergent and select a high temperature If in doubt wash the items several times P To prevent the risk of fire the following must not be dried in this tumble dryer items which have been cleaned using chemicals e g professional dry cleaning agents fabrics which contain a large proportion of rubber foam rubber or rubber like materials For example products made from latex foam rubber shower caps waterproof textiles rubberised articles and items of clothing and pillows with foam rubber filling damaged items which contain padding or fillings e g pillows jackets When damaged the filling can get out with the risk of igniting in the dryer P gt In many programmes the heating phase is followed by a cooling down phase to ensure that the items are not too hot to handle when you remove them this also avoids the danger of the laundry self igniting The
34. ever replaced it fits securely into the rear holders Otherwise it is not properly secure for transport 37 Installation Levelling the appliance The dryer must be perfectly level to ensure safe and proper operation m The screw feet can be adjusted to compensate for any unevenness in the floor The air inlet and outlet vents on the front of the dryer must not be covered as this would prevent sufficient ventilation for cooling the condenser unit 38 Do not block the gap between the bottom of the tumble dryer and the floor with plinth facings deep pile carpet etc This would hinder a sufficient flow of air to the dryer Room ventilation The air which is taken in when the dryer is in operation is blown out of the front of the dryer and warms up the air in the room It is very important to ensure adequate ventilation e g by opening a window Otherwise drying times may be longer Washer dryer stack The tumble dryer can also be combined with a Miele washing machine in a washer dryer stack The appropriate WTV stacking kit available to order to match your dryer is required Stacking kits must only be installed by a suitably qualified fitter Before moving the tumble dryer again e g when moving house After each use a small quantity of condensed water will collect in the area around the pump This water can run out if the dryer is tipped up when it is being moved It is a good ide
35. f four times P and 8 default setting will flash alternately in the display The number which appears alternately in the display with P means G Normal buzzer Default setting Loud buzzer The Automatic plus indicator light will also flash Pressing the Start Stop button switches from one to the other Switch the dryer off with the L button The setting you have selected is now stored in memory You can change it again at any time 47 Programmable functions Memory function The electronics will memorise any extra options selected for a programme The duration selected for the Warm air or Cool air timed drying programmes will also be stored in memory These settings will be selected automatically the next time the programme is chosen You can either accept these or change them by pressing the appropriate button Follow steps to to programme and store in memory Before you begin first ensure that The tumble dryer is switched off The door is closed 48 Press the Start Stop button and keep it pressed in whilst carrying out steps 0 9 Press the L button in Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button three times The Low temperature indicator light will briefly flash on and off six times P and 8 default setting
36. gramme Cleaning them whilst dry Tip You can also use a vacuum cleaner to remove the fluff 0000404040 HAHA HA et a a d m Open the door and pull the fluff filter 1 out of the door as illustrated m Use your fingers to remove the fluff from the surface of the filter 22 m Remove any fluff from the hollow part of the door opening You could also use a cleaning brush which is available as an optional extra from your Miele dealer or the Miele Spare Parts Department or use a vacuum cleaner m Also clean the door seal 2 with a damp cloth m Once clean push the filter back into the door holder until it clicks into position Ensure it is facing the correct way m Use your fingers or a vacuum cleaner to remove the fluff from the two fluff filters in the door opening m Close the door Always check the fluff filters if the Clean out airways indicator light comes on Cleaning and care Cleaning them with water If there is a great deal of compacted fluff on any of the filters they can be removed and cleaned under hot running water m Open the door and pull the fluff filter out of the door as described previously The two filters in the door opening can also be removed if you need to clean them with water m Turn dial and pull the filter by the dial out of the door opening as shown 2 Do the same on the other side m Rinse all the filters under hot running
37. guence Once a programme has started changing the programme You cannot change to another programme once a programme has started this prevents unintentional alterations You will need to cancel the current programme before you can select a new one cancelling the programme and then selecting a different programme m Press the Start Stop button The items will be cooled down depending on the temperature reached and how long they have been dried for If you press the Start Stop button again during the cooling down phase Finish will light up in the display m Press the Door button m Close the door m Select another programme and start it cancelling the programme and then removing the laundry m Proceed as described in Adding or removing laundry after a programme has started below m Switch the dryer off after closing the door Altering Delay start m See Delay start Adding or removing laundry after a programme has started m Press the Door button m Open the door N Danger of burning Do not touch the back of the drum when adding or removing items The drum and the items can get very hot m Add or remove items as required m Close the door m Press the Start Stop button Time remaining The time left shown in the display may now vary from the actual drying time Electronic system lock The system lock prevents the dryer being used without your knowledge It can be
38. h was running previously will continue automatically when power is restored to the tumble dryer as long as the Cooling down phase had not been reached The interior drum lighting does not come on The lighting switches off automatically to save energy Switch the dryer off and then on again Ifthe lamp needs to be replaced follow the instructions in Changing the lamp 33 Problem solving guide Changing the lamp Thelamp specification and Disconnect the tumble dryer from maximum wattage is stated on the the mains electricity supply data plate and on the lamp cover m Open the door m Replace the lamp You will find the interior lamp cover at m To close the cover push it upwards the top of the drum aperture and press it on the left and right until you hear it click into position N Ensure that it is fitted into position securely as any moisture could cause a short circuit m Insert a suitable tool such as a wide bladed screwdriver under the side edge of the lamp cover as illustrated m Apply alittle pressure and whilst doing so turn your wrist in the direction of the arrow to open the cover The cover will open downwards The temperature resistant lamp should only be ordered from your Miele Dealer or the Miele Spare Parts Department 34 After Sales service Repairs In the event of any faults which you cannot remedy yourself please contact
39. he load when drying There is a build up of fluff Fluff is principally the result of friction when garments are being worn and to some extent when they are being washed Machine drying hardly causes any fluff to form and has no appreciable effect on the lifetime of the fabric Fluff is collected by the fluff filters and can be removed easily see Cleaning and care You can alter the drying levels for some programmes see Programmable functions at the the end of this booklet 31 Problem solving guide Other problems Problem Possible cause Remedy The drying process goes on too long or even switches off In some circumstances the Clean out airways indicator light still comes on even though the filters are clean Please check all the possible causes and switch the dryer off and then back on again Ventilation to and from the dryer may be insufficient e g because it is installed in a room which is too small This can cause the temperature in the room to rise sharply Open a door or window while the dryer is in operation for increased air flow The vents below the door are blocked Remove any objects that are blocking the vents The fluff filters are clogged up with fluff or were still wet when they were replaced Remove any fluff The fluff filters must be completely dry Detergent residues hair and fine fibre
40. in delay start m Press the Start Stop button The Delay start indicator will light up constantly Delay start times of more than 10h will count down in hours and of less than 10h in minutes to the start of the programme The drum will turn briefly every hour to help prevent creasing To cancel alter delay start m Press the Start Stop button to cancel delay start m To alter the delay start time press the Delay start button repeatedly until the required delay period shows in the display m Press the Start Stop button to start the altered delay start time counting down from the beginning again To add laundry after the delay start time has started counting down While the delay start time is counting down you can still add laundry to the drum m Switch the dryer off Opening the door without switching the dryer off will cancel delay start m Open the door and add the laundry m Close the door and switch the dryer back on again Programme chart Cottons Max load 7 kg Extra dry Normal Fabric type Single and multi layered cotton fabrics such as towelling T shirts underwear flannelette bed linen Notes Select Extra dry for multi layered and very thick fabrics Do not use Extra dry for loopknit fabrics e g T shirts underwear baby clothes as they have a tendency to shrink Low temperature Select the Low temperature option for delicate fabrics with
41. ing at room temperature Proofing Max load 2 5 kg Normal Fabric type For drying microfibre fabrics skiwear fine closeweave cotton garments poplin or tablecloths which are suitable for drying in a tumble dryer and have been treated to provide a water and dirt resistant finish Notes This programme includes a proofing fixing phase Only use proofing agents which are stated by the manufacturer as being Suitable for use on membrane textiles as these contain fluorochemical compounds Do not dry items which have been treated with proofing agents containing paraffin Fire hazard Express Max load 3 5 kg Extra dry Normal Hand iron Machine iron Fabric type Fabrics which can tolerate high temperatures with the symbol on the care label and which can be dried in the Cottons programme Note The programme duration is shorter Automatic plus Max load 5 kg Normal Hand iron Fabric type Mixed loads of garments suitable for the Cottons and Minimum iron programmes Sort according to colour Denim Max load 3 kg Normal Hand iron Fabric type Denim garments e g jeans jackets skirts shirts Low temperature Select the Low temperature option for delicate fabrics with the symbol on the care label Weight of dry laundry Programme chart Shirts Max load 2 kg Normal Hand iron Fabric type Shirts and blouses Low temperature
42. ing out steps 6 8 Press the LA button in Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button seven times The Low temperature indicator light will flash on and off slowly once and will then flash on and off quickly twice P and G default setting will flash alternately in the display The number which appears alternately in the display with P means U Default setting i Adjusted for very soft water the Automatic plus indicator light will also flash Pressing the Start Stop button switches from one number to the other O Switch the dryer off with the 1 button The setting you have selected is now stored in memory You can change it again at any time 53 54 55 United Kingdom Miele Co Lid Fairacres Marcham Road Abingdon Oxon OX14 1TW Tel 01235 554455 Fax 01235 554477 Customer Contact Centre Tel 08707 554466 E mail info miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 03 9764 7130 Fax 03 9764 7149 Internet www miele com au China Miele Shanghai Suite 4105 06 Plaza 66 1266 Nanjing Road West Jing An District Shanghai 200040 PRC Tel 86 21 6288 4200 Fax 86 21 6288 4100 E mail mieleshanghai cn miele com Internet www miele cn
43. ly once and will then flash on and off quickly once P and G default setting will flash alternately in the display The number which appears alternately in the display with P means O Keypad tone deactivated Default setting i Keypad tone activated the Automatic plus indicator light will also flash Pressing the Start Stop button changes from one number to another Switch the dryer off with the 1 button The setting you have selected is now stored in memory You can change it again at any time 51 Programmable functions Adjusting the dryer s electronics for very soft water n some areas of the UK water is extremely soft which can affect the sensitivity of the control electronics If the dryer is installed in an area of very soft water you should contact your local water supplier for information and advice regarding water hardness and water conductivity If the water conductivity is less than 150 uS the following programmable function will need to be activated Important This programmable function should not be activated if despite the water being extremely soft as would be the case if a water softener were used its conductivity is greater than 150 US Follow steps to to programme and store in memory Before you begin first ensure that The tumble dryer is switched off The door is closed 52 Press the Start Stop button and keep it pressed in whilst carry
44. moothing O gt Door Low temperature button Delicate fabrics are dried at a lower temperature 2 Drying level button with indicator lights to show the drying level selected Display See next page Delay start button This button is used for Delaying the start of a programme Selecting the duration of the timed drying Warm air and Cool air programmes Buzzer button An audible tone sounds at the end of the programme Perfect Dry indicator For all drying level programmes See next page Check lights For a description of these see Problem solving guide After sales service Start Stop button For starting or cancelling a programme The button flashes while a programme is being selected and then lights up constantly when the programme has started Programme selector with indicator lights to show the programme selected Door button Pressing this button will open the door even when the dryer is switched off at the mains ad On Off button L For switching the dryer on and off Operating the tumble dryer The display shows Programme duration Programme stage Drying Cooling down Finish Check and fault messages The following are also selected via the display Duration of the Warm air and Cool air programmes Delay start You can select a programme and set it to start at a later time The programme will start automatically
45. next used If the dryer is switched on at the mains and the door is opened the drum lighting will come on It will go out a few minutes later to save energy m Switch the dryer off by pressing the L button m Clean the fluff filters m Close the door m Empty the condensed water container unless the dryer has been connected for external drainage m The condenser unit should be checked and cleaned on a regular basis see Cleaning and care Extra options Delay start Extra options Low temperature Delicate and minimum iron fabrics with the Q symbol on the care label e g acrylic garments are dried at a lower temperature The programme duration is longer On some programmes Low temperature is permanently activated and so cannot be deselected Buzzer A buzzer sounds at intervals for a maximum of 1 hr to let you know the programme has finished A continuous alarm will sound if there is a fault even if the buzzer has been switched off Delay start You can delay the start of a programme by 30 minutes up to 24 hours m Select a programme m Press the Delay start button repeatedly until the required delay period shows in the display The Delay start indicator light will flash Times of up to 10h are selected in steps of half an hour and more than 144 in one hour steps If you keep the Delay start button pressed in the time will continue to increase up to 24h To beg
46. nit m When rinsing the condenser unit make sure you position it as shown in the next two illustrations m Use a shower head or similar to rinse the unit out as shown Cleaning and care m Then flush the unit through from the front m Check the condenser unit again for any visible fluff and if necessary flush it through again until it has all gone m Also make sure the rubber seals are clean The rubber seals must not be removed and must be free of kinks Checking and cleaning the condenser unit housing m Remove any soiling still visible inside the housing unit by hand using a damp cloth Do not try and access areas you cannot reach by hand Replacing the condenser unit m With the handle facing upwards push the condenser unit back into position in its housing m Turn the lever down to the horizontal position making sure that the hook on the lever clicks into the groove When replacing the inner cover after cleaning ensure that the rubber seal fits correctly into the groove m Replace the inner cover making sure the hooks locate correctly Hold it at an angle and push it gently downwards m Then turn the lever upwards into the horizontal position to lock the cover m Replace the service panel and press the upper edge until it clicks into position AA It is important to ensure that both the condenser unit and the cover are correctly positioned and locked otherwise water may leak from the
47. on The buzzer sounds The condensed water container is full or there is kink in the drain hose Empty out the condensed water container Check the drain hose To switch off the indicator light Open and close the door 29 Problem solving guide will not start and the indicators for these programmes do not light up Problem Possible cause Remedy The Denim Shirts and No obvious cause Switch the dryer off Cool air programmes and then on again Select one of the programmes If the programme will still not start there is a fault Contact the Miele Service Department Use another programme in the meantime The Start Stop button flashes does not flash The flashing indicates that a programme can be started After the programme has started the flashing will change to a constant light 30 Problem solving guide An unsatisfactory drying result Problem Possible cause Remedy The laundry is not The load consisted of Finish drying using the sufficiently dry different fabrics Warm air programme Select a different programme next time Items made of synthetic fibres are charged with static electricity after drying Synthetic fibres tend to attract static charge Static charge can be reduced by adding a fabric conditioner to the final rinse in the washing programme or a fabric conditioner sheet to t
48. programme is not finished until the cooling down phase has been completed Ensure that you always wait until the end of the programme before removing the laundry P Warning Do not switch the tumble dryer off before the end of the drying programme If this was done and the laundry was then removed immediately it could give off a great amount of heat gt gt Fabric conditioner and similar products must be used according to the instructions on the manufacturer s packaging Warning and Safety instructions P gt The dryer must not be used without the fluff filters in place or if the fluff filters are damaged in any way P The fluff filters must be cleaned regularly P gt The dryer must not be used without the condenser unit in place P gt The fluff filters must be thoroughly dried after cleaning Damp or wet filters could cause operational faults gt Do not install the tumble dryer in a room where there is a risk of frost occurring At temperatures around freezing point the tumble dryer may not be able to operate properly There is a risk of damage if the condensed water is allowed to freeze in the pump hoses and or condensed water container The ambient room temperature should be between 2 C and 35 C P If the water is drained externally through the drain hose instead of being collected in the condensed water container make sure the drain hose is securely attached if you hang it ina sink or basin to
49. s can block the condenser unit Check the condenser unit from time to time and clean it if necessary The laundry has not been spun sufficiently Make sure that your laundry is thoroughly spun at the appropriate spin speed in the washing machine The tumble dryer has been overloaded Do not exceed the maximum load for the programme selected Metallic components e g zips have prevented the dryer from registering the correct moisture level in the laundry Open zips next time If the problem occurs again dry garments with long zips using the Warm air programme timed drying 82 Problem solving guide Problem Possible cause Remedy Water leaks from the The inner cover of the Ensure that the dryer after the condenser unit has not condenser unit is condenser unit has been cleaned been locked properly and or the condenser unit has not been positioned correctly Fluff has collected in the condenser unit housing positioned correctly and lock the inner cover Check the rubber seals Use a cloth to remove any visible fluff from the inside of the condenser unit housing The programme does not start No obvious cause Is the dryer switched on Is the plug correctly inserted into the socket and switched on Is the door closed properly Has the fuse or circuit breaker tripped Power cut A programme whic
50. ssential for the before using the dryer correct functioning of your appliance Please do not therefore dispose of your appliance with your household waste ys Disposal of your old appliance Make sure the room in which the dryer is located is well ventilated Check the condenser unit from time to time and clean it when necessary Please dispose of it at your local community waste collection recycling centre or contact your Dealer for advice Ensure that it presents no danger to children while being stored for disposal Contents Caring for the environment 2 Warning and Safety instructions 5 Operating the tumble dryer 9 Control Panel a a ga Nk b a EN tee aod hase yay ple babe ag Ga bani a eas 9 Notesonlaundrycare 11 Garmentcarelabelsymbols 11 MIPS ON ONANG IIIA 11 How to dry correctly 12 Brief INSWUCIONS sacs alan a a eye heed eee a Bg Ree Pe ae RPP eb beatae a 12 Extra options Delaystart 15 EXTA OOUOMS IAA Na a ie Ada ida deat ak ot 15 LOW aa Aa AAA aaa era taiwan cede Pade whe bea due eae 15 BUIZZCR so af ot oa AWA TABU NORA tier oe ete Aa ee Gane BAe eae tae 15 BENA STAM 2 3 crit b ambata oh Gon Gek ai la anak Sabet dh
51. t If the connection cable is faulty it must only be replaced by a Miele approved service technician to protect the user from danger P In the event of a fault or for cleaning purposes the tumble dryer is only completely isolated from the electricity supply when it is switched off at the wall socket and the plug is withdrawn or itis switched off at the mains or the mains fuse is disconnected or the screw out fuse is removed in countries where this is applicable P gt This tumble dryer may only be used in mobile installations such as ships if a risk assessment of the installation has been carried out by a suitably qualified engineer P In countries where there are areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the tumble dryer and its surroundings in a clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee gt Do not make any alterations to the tumble dryer unless authorised to do so by Miele Warning and Safety instructions Correct use P To prevent the risk of fire the following textiles must not be dried in this tumble dryer items which have not been washed items such as workwear which have not been thoroughly cleaned and which are still soiled with grease oil or other deposits Such as cosmetics lotions etc If items have not be
52. ton in Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button once The Low temperature indicator light will briefly flash on and off three times P and default setting will flash alternately in the display The number which appears alternately in the display with P means G Anti crease deactivated 1 1 hour anti crease The Automatic plus indicator light will also flash once 2 hours anti crease The Automatic plus indicator light will also flash twice default setting Pressing the Start Stop button switches from one number to another Switch the dryer off with the L button The setting you have selected is now stored in memory You can change it again at any time Programmable functions Altering the volume of the buzzer The buzzer has two volumes Follow steps to to programme and store in memory Before you begin first ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 6 8 Press the L button in Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button twice The Low temperature indicator light will briefly flash on and of
53. water m Then shake the filters until no more water droplets are visible m Dry the filters thoroughly with care m Clean the area underneath these filters e g with a vacuum cleaner Do not replace them if they are damp or wet Damp or wet filters could cause operational faults m Push the large filter back into the door holder until it clicks into position Ensure it is facing the correct way m Replace the filters in the door opening by first inserting them at the bottom and then pressing them into place at the top m Lock both dials 23 Cleaning and care Cleaning the tumble dryer Disconnect the tumble dryer from the mains electricity supply Miele branded cleaning and conditioning products are available to order from your Dealer the Miele Spare Parts Department or via the internet on www miele shop com m Clean the housing and control panel with a slightly damp cloth and a mild detergent or soapy water m The drum and other stainless steel parts can be cleaned with a suitable propietary stainless steel cleaner following the manufacturer s instructions Do not use solvents abrasive cleaners glass cleaners or all purpose cleaners These could damage plastic sufaces and other parts The tumble dryer must never be hosed down m Dry all parts with a soft cloth 24 Cleaning and care Cleaning the condenser unit Detergent residue hair and fine fluff from the dryer can get through
54. will flash alternately in the display The number which appears alternately in the display with P means U Memory deactivated default setting Memory activated the Automatic plus indicator light will also flash Pressing the Start Stop button switches from one to the other Switch the dryer off with the 1 button The setting you have selected is now stored in memory You can change it again at any time Programmable functions Extending the cooling down time The cooling down phase which takes place before the end of a programme can be lengthened if required This makes the garments easier to handle The cooling down time can be extended by 5 minutes or 10 minutes can only be extended for programmes with drying levels Follow steps to to programme and store in memory The programmable functions are activated with the buttons Before you begin first ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 6 0 Press the L button in Wait until the indicator light for the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button four times The Low temperature indicator light will briefly flash on and off seven times P and G default setting will flash alternately in the display
Download Pdf Manuals
Related Search
Related Contents
プロサイクリストや競技志向のサイクリストから高い支持を得ている Manuel d`Utilisation TP-Link TD-8616 V7 Declaration of Conformity HP EC301 Magenta 排気ファン取扱説明書 [ EXT 008U-02 ] Manual de recuperação e resolução de problemas 石綿障害予防規則の改正について Guía de estudio Curso 2011/2012 LEAPER-56 Universal IC Writer User`s Manual Copyright © All rights reserved.
Failed to retrieve file