Maytag PAVT-5 Washer User Manual
Contents
1. Your new washer is designed to handle out of balance loads without shutting down or interrupting the washing cycle For this reason the cycle will always be completed If heavier fabrics in such out of balance loads should ever contain excessive moisture at the completion of the cycle redistribute the clothes in the washer and reset the control dial for the final spin period F Care amp Cleaning After washing leave the lid open until the interior is dry 1 2 Check hoses to be sure there are no kinks or knots 3 Your washer should not be installed where temperatures will go below freezing as damage to the washer could result 4 To clean occasionally wipe exterior with a clean damp sponge or cloth Do not use polish on plastic parts 5 Lifetime lubrication is done at the factory so your washer never needs to be oiled or greased 6 Do not lay heavy or sharp objects on top of your washer 7 The top of the washer should not be used for removing stains from garments Some stain removers such as rust remover will mar the finish 8 Remove pins buckles or other sharp objects from clothes to prevent scratching interior parts 9 Clothes should not be stored in washer 10 Bleach detergent solvents etc spilled on the top of your washer that are allowed to remain will remove the glossy finish Remove all spills with a damp soft cloth 11 If you close your home for the winter have a servic2. appliance safely the operator should become familiar with the instructions for operation of the appliance and always exercise care when using it 3 Do not install or store this appliance where it will be exposed to the weather 4 Install and level washer on a floor that can support the weight 5 This appliance must be properly grounded Never plug the appliance cord into a receptacle which is not grounded adequately and in accordance with local and national codes See installation instructions for grounding this appliance 6 To avoid the possibility of fire or explosion a Do not wash items that have been previously cleaned in washed in soaked in or spotted with gasoline dry cleaning solvents other flammable or explosive substances as they give off vapors that could ignite or explode Hand wash and line dry any items containing these substances Any material on which you have used a cleaning solvent or which is saturated with flammable liquids or solids should not be placed in the washer until all traces of these liquids or solids and their fumes have been removed These items include acetone denatured alcohol gasoline kerosene some liquid household cleaners some spot removers turpentine waxes and wax removers b Do not add gasoline dry cleaning solvents or other flammable or explosive substances to the wash water These substances give off vapors that could ignite or explode c Under certain conditio
3. Infinite Water Level control allows you to e select a specific setting or anywhere in between It may become necessary due to bulky fabrics to adjust the water level after agitation begins To adjust the water level turn the control to reset and then back to the desired setting WATER LEVEL SETTING LOAD SIZE sma STEP 3 i MAYTAG Performa Heavy Duty SuperSize Capacity 3 Speed Select Medium e R Select Wash Spin Speed Super 2 3 Full Your washer has selectable wash and spin speed combinations Note Items must circulate freely for best results WASH SPIN LOAD TYPE SPEED Sturdy fabrics needing maximum STEP 2 pry water extraction like jeans towels Select Wash Rinse Temperature ane Beading Your washer gives you a choice of hot warm or cold Wrinkle Control water for washing and cold or warm water select Gentle Fast models for rinsing Delicate fabrics needing slower spin WASH RINSE LOAD TYPE ae speed because of clothing TEMPS construction Hot Cold White and heavily soiled color fast items Note In wash water temperatures below 60 F Slow agitation to gently wash fabrics followed by a fast spin to remove moisture NOSE TaIEy SONET Cole ates 16 C detergents do not dissolve well or clean Warm Cold 1 OSE Eee ems well Care labels define cold water as up to 85 F Cold Cold Brightly colored lightly soiled 29 C items washable woolens np Wash Spin Speed Wrinkle Contr
4. cycle at the point it was interrupted Troubleshooting Won t Spin or Drain Fills with the Wrong Temperature Water Cycle Selector Advances Through Off Plug cord into live electrical outlet Check fuse or reset circuit breaker Turn the control dial to proper cycle and restart the washer Turn both faucets on fully Straighten inlet hoses Disconnect hoses and clean screens Hose filter screens may be plugged Check fuse or reset circuit breaker Make sure the lid is completely closed Turn the control dial to proper cycle and restart the washer Pauses are normal Wait and see if the washer will start again Check fuse or reset circuit breaker Straighten drain hoses Eliminate kinked hoses If there is a home drain restriction call for drain service Close lid and restart the washer For your safety washer will not spin unless the lid is closed Suds lock caused by too many suds Rewash without detergent Use correct amount of a low sudsing detergent Unevenly distributed load Redistribute the load close the lid and restart the washer Check for leveling Be sure water level is acceptable for load size A fast spin speed or Normal agitation is recommended for heavy loads like jeans or towels Plug cord into live electrical outlet Check fuse or reset circuit breaker Close lid and restart the washer For your safety washer will not agitate or spin unless lid is closed This may be a pause in t
5. AD TYPE ae speed because of clothing TEMPS construction Hot Cold White and heavily soiled color fast items Note In wash water temperatures below 60 F Slow agitation to gently wash fabrics followed by a fast spin to remove moisture Moderately soiled colored items 16 C detergents do not dissolve well or clean Moderately soiled colored items well Care labels define cold water as up to 85 F Warm Cold o most wrinkle free items 29 C Brightly colored lightly soiled items washable woolens Cold Cold Control features vary by model i Wrinkle Control mp Wash Spin Speed 2 p Regular i 6 Wrinkle Control Spin a 6 Gentle Fast Regular Delicate Normal Fast Gentle Slow Rinse Cold bs Rinse J old Off Spin 8 n4 kinse Spin Pull to Start Push to Stop Quiet Series 100 13 Cycles UD 4 Ss 5 Select Cycle Pull Control Dial Out to Start To select a cycle push the control dial in off position You may stop the washer at any time by simply and turn it to the right clockwise until the pointer is at pushing the control dial in Therefore it is possible to the soil level needed for the wash load obtain a non agitated soak or to shorten skip or repeat any part of a cycle The control dial must be Important F ti fabri th iat as mp Pe ee pushed in off position when you change the setting wash and spin speed for the load type must be selected using the Wash Spin Sp
6. Instructions appearing in this guide are not meant to cover all possible conditions and situations that may occur Common sense caution and care must be exercised when installing maintaining or operating appliance Always contact the manufacturer about problems or conditions you do not understand Recognize Safety Symbols Words Labels Important Safety Instructions Do not add gasoline dry cleaning solvents or other flammable or explosive substances to the wash water These substances give off vapors that could ignite or explode Do not wash articles which have been previously cleaned washed soaked or spotted with gasoline dry cleaning solvents oil waxes chemical solvents alcohol turpentine or other flammable or explosive materials These substances will be retained in articles and articles which still contain these flammable or explosive substances give off vapors that could ignite or explode Observe these precautions when using cleaning fluids spot or stain removers etc These products should be labeled nonflammable Use according to manufacturers directions in a well ventilated area or outdoors Thoroughly rinse articles by hand before placing them in the washer Some of these products rust removers for example will damage components and the finish of the washer Keep area around and underneath washer free from the accumulation of combustible materials such as lint paper rags gasoline and
7. PAVT 5 Emi Washer Use amp Care Guide Table of Contents Important Safety Instructions 1 2 Using the Controls 3 Speed 10 cycles 5 6 3 Speed 13 cycles 7 8 z Operating Tips 3 Special Features 9 10 Troubleshooting 4 Care amp Cleaning 10 J Service Information 11 Form No B 10 05 Part No 2205433 Rev B Litho U S A 2005 Maytag Appliances Sales Co Installer Please leave this guide with this appliance Consumer Please read and keep this guide for future reference Keep sales receipt and or canceled check as proof of purchase Have complete model and serial number identification of your appliance This is located on the back center of the control panel Record these numbers below for easy access Model Number Serial Number Date of Purchase In our continuing effort to improve the quality and performance of our appliances it may be necessary to make changes to the appliance without revising this guide Note When writing or calling about a service problem please include the following information a Your name address and telephone number b Model number and serial number c Name and address of your dealer or engineer d A clear description of the problem you are having e Proof of purchase sales receipt What You Need to Know About Safety Instructions Warning and Important Safety
8. all other flammable vapors and liquids HYDROGEN GAS IS EXPLOSIVE Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for two weeks or more If the hot water system has not been used for such a period before using the washer turn on all the hot water faucets and let the water flow from each faucet for several minutes This will release any accumulated hydrogen gas As this gas is flammable do not smoke or use an open flame during this time Recent studies have shown that if vegetable oil contaminated materials are incompletely washed a carry over and buildup of the oil may contribute to a chemical reaction spontaneous combustion that could cause a load to catch fire by itself This would be more likely to happen if the load were left in the dryer after tumbling stopped or if items were folded and stacked while warm A WARNING WARNING Hazards or unsafe practices which COULD result in severe personal injury or death A CAUTION CAUTION Hazards or unsafe practices which COULD result in minor personal injury FIN Important Safety Instructions A WARNING To reduce the risk of fire explosion electric shock or personal injury when using your washer follow basic safety precautions including the following 1 Read all instructions before using the appliance 2 As with any equipment using electricity and having moving parts there are potential hazards To use this
9. ch as detergents bleach etc out of the reach of children preferably in a locked cabinet Use laundry aids only as directed by the manufacturer Observe all warnings on container labels Keep the area around and underneath washer free from the accumulation of combustible materials such as lint paper rags gasoline and all other flammable vapors and liquids Do not use chlorine bleach and ammonia or acids such as vinegar or rust remover in the same wash Hazardous fumes can form Do not machine wash fiberglass materials Small particles can stick to fabrics washed in following loads and cause skin irritation For flame resistant finishes follow garment manufacturer s instructions carefully Improper laundering could remove the finish Before the appliance is removed from service or discarded remove the door to the washing compartment Inlet hoses are subject to damage and deterioration over time Check the hoses periodically for bulges kinks cuts wear or leaks and replace them every five years SAVE THESE INSTRUCTIONS 4 Operating Tips Detergent Use either liquid or granular laundry detergent For best results be sure detergent is added to the washer BEFORE the load and be sure the wash water is above 60 F 16 C Use the correct amount of detergent for the load size soil level and water conditions Use more detergent if you have hard water and very soiled loads If you have sof
10. e technician drain the washer Unplug cord from electrical outlet and disconnect hoses from faucets Overload Protector A built in protector automatically shuts off the washer motor in case of an overload This can occur if e The load being washed is too heavy Too many appliances are plugged into the line operating your washer A low voltage condition exists on the line e Lid is opened and closed repeatedly The overload protector permits the washer to start again when the motor has cooled to a safe operating temperature If the motor stops repeatedly call your service technician Cleaning the Interior Clean the interior of the washer periodically to remove any dirt soil odor mold mildew or bacteria residue that may remain in the washer as a result of washing clothes We recommend taking the following steps every 60 to 120 days to clean and freshen your washer interior The frequency with which the washer should be cleaned and freshened depends on factors such as usage the amount of dirt soil or bacteria being run through your washer or the use of cold water Failure to follow these instructions may result in unsatisfactory conditions including unpleasant odor and or permanent stains on the washer or wash load To clean and freshen the washer interior 1 Add a measured amount of chlorine bleach to the bleach dispenser following package directions 2 Add 1 4 cup of detergent to the tub 3 Run the wash
11. eed knob Note Do not attempt to turn the control dial Regular This cycle provides up to 22 minutes of agitation Select the Regular Wash Spin Speed setting counterclockwise Damage to the timer will result Delicates Delicate is designed for items requiring delicate wash action Select the Delicate Wash Spin Speed setting Wrinkle Control This cycle is designed for most loads For lightly to normally soiled garments Select the Wrinkle Control Wash Spin Speed setting Special Features Liquid Bleach Dispenser The dispenser automatically dilutes liquid chlorine bleach before it reaches your wash load To use follow these steps 1 Measure liquid chlorine bleach carefully following the instructions on the bottle 2 Pour liquid chlorine bleach into bleach dispenser before adding the load Avoid splashing or over filling the dispenser e Never pour undiluted liquid chlorine bleach directly onto the load or into the wash tub It is a powerful chemical and can cause fabric damage such as tearing or color loss if not used properly e If you prefer to use color safe non chlorine bleach pour it into the wash tub with your detergent Do not pour non chlorine bleaches into the bleach dispenser Fabric Softener Dispenser The dispenser automatically releases liquid fabric softener at the proper time during the cycle To use follow these steps 1 Pour a measured amount of fabric softener into t
12. er without a load through a complete cycle using hot water 4 Repeat the process if necessary 10 Service Information For service please contact the Maytag dealer from whom you purchased this appliance For service in Australia please contact Maytag Appliances on 1 300 858 575 ABN 88 086 686 884 Manufacturer MAYTAG APPLIANCES 1 Dependability Square Newton IA 50208 U S A Form No B 10 05 Part No 2205433 Rev B Litho U S A 2005 Maytag Appliances Sales Co
13. he cycle Wait briefly and it may start Make sure hose connections are tight Make sure end of drain hose is correctly inserted and secured to drain facility Avoid extended soaking soak for 30 minutes or less Avoid overloading Be sure washer is leveled properly as outlined in installation manual Weak floors can cause vibration and walking Operating sounds will vary depending on agitation speed Turn both faucets on fully If equipped with a temperature selector dial be sure it is set directly on a temperature setting and not between settings Make sure temperature selection is correct While the washer is filling you may notice just hot and or just cold water entering the tub when cold or warm wash temperatures are selected Make sure hoses are connected to correct faucets and inlet connections Be sure water supply is regulated correctly Flush water line before filling washer Check the water heater It should be set to deliver a minimum 120 F 49 C hot water at the tap Also check water heater capacity and recovery rate Disconnect hoses and clean screens Hose filter screens may be plugged Extra Rinse select models is selected Select Water Level ee a Determine the selected setting based on clothes load Mactan ss au g P b 0 size Selection should provide sufficient water to permit ea oo Cold J 7 P a clothes to circulate freely during agitation On select Mini Se Super y models the
14. he dispenser to fill line only 2 If fabric softener comes below line add warm water If it is necessary to clean the dispenser 1 Pull the dispenser off of the top of the agitator 2 Soak for one hour in sink or container in hot water and dishwashing liquid 3 Hold hands over top and bottom of dispenser and shake to loosen buildup F D T 4 a A py ii S 4 Rinse with clean hot water 5 Repeat process if necessary 6 Replace dispenser on agitator Do not use dishwashing liquid inside the washer Oversudsing can occur Automatic Lint Filtering System The Lint Filtering System does not require cleaning Wash and rinse water is filtered and re filtered continuously to trap lint shed by most fabrics during the agitation cycle before it can be redeposited on the wash load The engineered hole design on the wash basket in conjunction with water flow produced by the agitator traps lint away from the clothes between the inner wash basket and the outer tub Lint is automatically flushed from the washer during the spin cycle Safety Spin If for any reason you open the washer lid when the washer is in a spin or extract period the operation will immediately stop This is for your personal safety If your washer does not stop call your service technician immediately When the lid is closed the operation will automatically resume Special Features Unbalanced Spin Load Compensator
15. ns hydrogen gas may be produced in a hot water system that has not been used for two weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for such a period before using a washer or combination washer dryer turn on all hot water faucets and let the water flow from each for 19 several minutes This will release any accumulated hydrogen gas As the gas is flammable do not smoke or use an open flame during this time d Do not wash or dry items that are soiled with vegetable or cooking oil These items may contain some oil after laundering Due to the remaining oil the fabric may smoke or catch fire by itself Do not reach into the appliance if the tub or agitator is moving Do not allow children or pets to play on in or in front of the appliance Close supervision is necessary when the appliance is used near children and pets Do not tamper with controls Do not repair or replace any part of the appliance or attempt any servicing unless specifically recommended in published user repair instructions that you understand and have the skills to carry out Unplug power supply cord before attempting to service your washer Service is to be done only by qualified service personnel The agitator should not be removed If the agitator is removed it must be replaced by pushing down completely and the locking screw tightened before the washer is operated Keep all laundry aids su
16. ol a Gentle Fast cold Regular n Delicate old Normal Fast Gentle Slow 10 Cycles Control features vary by model Extra Rinse f Off Pull to Start Push to Stop Wrinkle Control Si 4 Select Cycle To select a cycle push the control dial in off position and turn it to the right clockwise until the pointer is at the soil level needed for the wash load Important For optimum fabric care the appropriate wash and spin speed for the load type must be selected using the Wash Spin Speed knob Regular This cycle provides up to 15 minutes of agitation Select the Regular Wash Spin Speed setting Wrinkle Control This cycle is designed for most loads For lightly to normally soiled garments Select the Wrinkle Control Wash Spin Speed setting Delicates Delicate is designed for items requiring delicate wash action Select the Delicate Wash Spin Speed setting Sia 5 Select Options if desired Extra Rinse When the knob is in the On position an additional rinse at the end of the Regular Wrinkle Control and Delicate cycles is provided to more completely remove laundry additives suds perfumes etc Sia 6 Pull Control Dial Out to Start You may stop the washer at any time by simply pushing the control dial in Therefore it is possible to obtain a non agitated soak or to shorten skip or repeat any part of a cycle The control dial must be pushed in off position when you change the set
17. t water or a lightly soiled load use less detergent See manufacturer s instructions Wipe up any detergent spills on the washer Loading For best results add the detergent to the washtub before adding the load Put dry unfolded clothes loosely in the tub up to the top row of holes for a maximum load Do not wrap large items like sheets around the agitator Mix large and small items for best circulation Wash bulky items like blankets separately When laundering wrinkle free items or items of delicate construction washable woolens or loosely knit items never use less than the Medium water level setting This will minimize shrinkage wrinkling and pulling of seams Close lid carefully to avoid slamming Additional Tips During the spin it is possible for the load to become unevenly distributed in the tub If this happens push in the control dial open the lid redistribute the load close the lid and restart the washer The spin will resume at the point it was interrupted The washer will pause briefly throughout each cycle These pauses are normal e This washer is designed so that it will not agitate or spin when the lid is open It will however fill with the lid open so water is available for pretreating stains or diluting fabric softener e If you open the lid during a spin cycle the washer will stop When the lid is closed and the washer is restarted the washer will continue the
18. ting Note Do not attempt to turn the control dial counterclockwise Damage to the timer will result Using the Controls 3 Speed 13 cycles Infinite Water Level Wash Rinse Tel Select Water Level j i Warm Warm Determine the selected setting based on clothes load Small e large Warm Cold se la size Selection should provide sufficient water to permit a r l Hot X 7 ini uper oid clothes to circulate freely during agitation On select x ec G models the Infinite Water Level control allows you to select a specific setting or anywhere in between It may become necessary due to bulky fabrics to adjust the water level after agitation begins To adjust the water level turn the control to reset and then back to the desired setting QW MayraG Performa Heavy Duty SuperSize Capacity 3 Speed Select WATER LEVEL SETTING LOAD SIZE i a _ a _ d UID 3 Mets e _ V2 2 3 Select Wash Spin Speed Super 2 3 Full Your washer has selectable wash and spin speed combinations Note Items must circulate freely for best results WASH SPIN LOAD TYPE SPEED Sturdy fabrics needing maximum STEP 2 Peery ae water extraction like jeans towels Select Wash Rinse Temperature enidpedang Your washer gives you a choice of hot warm or cold Wrinkle Control water for washing and cold or warm water select Gentle Fast models for rinsing Delicate fabrics needing slower spin WASH RINSE LO
Download Pdf Manuals
Related Search