Marantz RC1200 Universal Remote User Manual
Contents
1. Qe amp wm The remote controller will do nothing if no macros are programmed The macro steps are executed in order and the names of their buttons are displayed on the LCD Also the step numbers displayed on LCD disappear as each step is executed 2 After all macro commands have been transmitted the remote controller returns to normal mode To cancel the transmission of a programmed macro use the v Cursor button STOP button 24 EXAMPLES OF MACRO PROGRAMS Example 1 Change the input source for the amplifier to CD and play the 3rd track on a CD in the CD player 1 Use a ballpoint pen or other sharp point to press the MACRO button 2 qe SOURCE D COND GO Cor 00 MACRO MODE J 2 Press the CD function button 8 CD M is 3 Press CD 8 3 17 OK 10 in this order Ovo e CD amp DIS HALL OSD SLEEP 25 HSITSNA When you are finished programming the macro use a ballpoint pen or other sharp point to press the MACRO button 2 Now execute the macro you just programmed 1 Press the CD Function button 8 for seconds 2 The macro commands are transmitted to the components in order and the names of the operations being performed are displayed on the LCD in order OBB2. Example 2 Turn the main amplifier ON Change the amplifier s input source to LD Set the Surround mode to DOLBY Switch the TV to video input Set the laser disc player to PLAY 1 Use a ballpoint pen or other sharp point to press the MACRO button 2 Pressthe LD button 8 N Bo ues GD Gm AUTO DOLBY THX DTS e Here the LD Function button 8 is used as the macro button but any function button can in fact be used 26 3 To set the various steps of the macro press the following buttons in order AMP 8 POWER ON 3 LD 8 AMP 8 2 DOLBY 17 TV 8 VIDEO use Jog Dial 7 to select VIDEO and press ENT button 6 LD 8 10 4 When you are finished programming the macro use a ballpoint pen or other sharp point to press the MACRO button 2 The remote controller returns to normal mode 9 2 Now execute the macro you just programmed 1 Press the LD Function button 8 for seconds GS 9 CD e The macro commands are transmitted in order and the names of the operations being performed are displayed on LCD in order When executing this macro function operations and LD only switch the command set of the remote controll
3. 1 MATRIX MOVIE 2CH 050 s Dolby Pro Logic and the double D symbol are trademarks of Dolby Laboratories Confidential Unpublished Works 1992 1997 Dolby Laboratories Inc All rights reserved DTS and DTS Digital Surround are trademarks of Digital Theater Systems Inc 1996 Digital Theater Systems Inc All rights reserved Lucasfilm and THX are registered trademark of Lucas film Ltd IM aAa rani is a registered trademark www marantz com Printed in Japan 00 02 287W851250 MITi
4. HSITSNA e In the rare event that NG appears on the LCD it means that the remote controller you are attempting to learn from uses special signals that cannot be learned by the Marantz remote controller 6 Follow the same procedure to make the remote controller learn the ten key 7 operation used by the laser disc player s remote controller 7 Repeat the procedure from step to have the remote controller learn the signal codes for the other components such as TV VCR etc If no buttons are pressed for approximately 1 minute while in the LEARN mode the remote controller automatically returns to the USE mode When programming the function buttons first switch to the desired function then press the button again 8 When you have finished programming the remote controller use a ballpoint pen or other sharp point to once again press the MODE button 1 to return it to the USE mode The LCD displays the USE indicator and the newly programmed codes now can be used If FULL is displayed on the LCD If FULL is displayed on the LCD when programming in the LEARN mode it means that the memory has become too full to hold any further codes If FULL is displayed no matter how many times you attempt to enter new codes it means that the remote controller cannot accept any new codes until some of the previously learned codes are deleted to make space in the memory Select unneeded codes for each of the Jog Di
5. gt appears again at LCD En UD e DOLBY THX DTS MATRIX MOVIE 2CH 050 SLEEP 3 Press the CD function button 8 on the copy source turn the Jog Dial 7 to select 1 DISC and then press the ENT button 6 for seconds 34 CD appears at LCD and then the 1 DISC characters stop blinking and remain lighted The Jog Dial name is a displayed 2 The copy source has now been oj established 2 CPY appears at LCD 8 4 The copy destination is selected next Press the DVD function button 8 turn the Jog Dial 7 to select 1 OSD and then press the ENT button 6 for 3 seconds DVD appears at LCD and then the 1 OSD characters stop blinking and remain lighted The Jog Dial name is displayed When copying finishes the OK display appears at LCD 8 appears again at LCD Now repeat steps 3 and 4 When copying is completed press the MODE button 1 and call up the USE display Operating tip In the same way copying is possible from Jog Dial 7 to a button other than jog and vice versa Now repeat steps 3 and 4 When copying is completed press the MODE button 1 and call up USE on the LCD display 35 HSITON3 OTHER FUNCTIONS LIGHTING BUTTON To allow easy use in a location which has
6. memory so that the learned codes will be retained even if the batteries are removed e PRESET CODES Function buttons already contain preset codes using the RC 5 RC 6 remote control language for other remote controllable Marantz audio visual component This does not apply to some of the buttons LCD LIGHTING FUNCTION AND LUMINOUS BUTTONS To allow easy use in a location which has been darkened for a home theater performance for instance this remote controller features an LCD backlight with electroluminescence EL and luminous buttons which can store light LARGE EASY TO READ DISPLAY Large LCD liquid crystal display messages and other information at a glance JOG DIAL The function selected by Jog Dial displayed on the LCD can be operated directly by the enter button MACRO CAPABILITY Macro function allows the remote controller to be programmed to execute complex strings of multiple commands using a single keystroke NAME ASSIGNMENT Allows one to change the displayed via the LCD name for a function button CLONING FUNCTION The unit features a cloning system that enables a duplicate unit of this remote controller which has already been programmed to be easily made by undertaking a series of key operations 2 NAMES OF PARTS amp FUNCTIONS Names of Buttons amp Functions 1 MODE button Used to change the operation mode of the remote controller Pressing this button cycles the remote
7. 1 Remove the back cover 2 Insert the new batteries AA type with correct and polarity BASIC OPERATION USE MODE The remote controller will normally be used in the USE mode It comes preset with codes commonly used to control 11 types of components manufactured by Marantz Philips and RCA for DSS including DSS DVD TV LD VCR AUX TUNER CD TAPE CD R MD and AMP as well as many others that utilize the RC 5 remote control language 1 Press once one of the Function buttons 8 to change to another component s commands such as LD button ep ovo DSS TV VCR AUX KD G amp D WD AUTO DOLBY 2 LD will be displayed on the LCD and the function codes will be set to operate the laser disc player and if you double clicked the LD function button the amplifier or receiver s input will be changed as well 3 Now you can operate the laser disc player When a button is pressed the symbol indicates that a remote code is being transmitted is not displayed if a button for which no code has been set is pressed 4 The Jog Dial 71 is used to select any one of up to 10 direct operations that can be performed for each of the 11 functions including LD TV and AMP Rotate the Jog Dial select one of these commands The number of the current page is indicated by at LCD The signal is sent when the ENT butt
8. EDITING MACROS Macros may be edited using following procedure 1 Use a ballpoint pen or other sharp point to press the MACRO button 2 until the MACRO and LEARN indicators are displayed blinking on the LCD Press the Function button 18 to be changed Let s use the example of the laser disc player by pressing the LD Function button 8 LD M is displayed blinking on LCD The number of steps in the completed macro is highlighted on LCD In this example there are 3 macro programs in memory 22 2 2 Li The is highlighted if no macros have been programmed and the remote controller is ready for macro programming 3 While pressing the VOL A button 9 press the and v Cursor button 10 to call up the part of the macro to be changed Once the part is displayed release the buttons Pressing the button increments the step number conversely pressing the v button decrements the step number To change a step by overwriting it press the button in which the new step will be memorized What was previously programmed will be cleared and overwritten with the new step To insert a new step in between existing steps in a macro after step 3 press the MEMO button 16 then press the button for the new step The numbers of the other steps will be adjusted accordingly to accommodate the new step Since only 10 steps ma
9. OK Cursor button e f you wish to rewrite the name input the desired characters using the ten key 117 The part of the display which is be overwritten can be moved using he left and right gt Cursor buttons 19 When you are finished rewriting press the OK Cursor button 9 To simply erase already existing characters press the O button to replace them with a blank space Refer to next section on rewriting names 6 Use the same procedure to program the codes for other 1 6 with the Jog Dial 7 7 When finished programming the codes for each of the buttons use a ballpoint pen or other sharp point to press the MODE button 1 to return the remote controller to the USE mode The LCD displays USE indicator and the newly programmed codes now can be used REWRITING NAMES This remote controller allows the names accessible by Jog Dial 7 to be rewritten with new ones of your choosing e Rewriting of names is performed for each individual function Let s use a laser disc player as an example to show how to change the SIDE A to LD A 1 Use a ballpoint pen or other sharp point to press the MODE button 1 to switch the remote controller to the NAME mode The NAME indicator blinks 2 Press the LD Function button 8 The left hand edge of the function name now blinks cD DVD CD R MD 0 9 5 3 Use the J
10. be pointed toward the source remote controller when using Programmable Learning function 19 LIGHTING button When this button is pressed the LCD display ights up and it goes off 5 seconds later While it is held down the display remains ighted Note The programmable learning function does not work with buttons 1 2 6 11 and 19 I 9 2 LCD Liquid Crystal Display Information about currently selected functions and modes is displayed on the LCD Pressing any buttons will call up a full display of information on the status of that function or mode This display will disappear after approximately 1 minute except for the Function Name indicator which is always displayed I IA NAL INA INA IN INL TANT oy Iz ZI I PHIM EM aM int ATO a EE Function Name indicator Displays the name of the currently selected function LD TV etc using up to 5 characters Command Name indicator Displays up to 10 types of commands for each function using up to 5 characters Command Page indicator Allows confirmation of current command page of Jog Dial 7 Also when setting or transmitting macros displays information such as the number of macro steps and the time intervals between command transmissions Tr
11. ERRA a Model RC1200 User Guide Learning Remote Control MAIN FEATURES 8 FUNCTIONS NAMES OF PARTS amp FUNCTIONS LOADING BATTERIES BASIC OPERATION USE MODE ooo LEARN MODE tins PROGRAMMING THE JOG DIAL REWRITING NAMES ses ERASING PROGRAMMED CODES 16 PROGRAMMING MACROS 20 EDITING MACROS sees 22 USING MACROS 24 EXAMPLES OF MACRO PROGRAMS 25 CLEARING MACRO PROGRAMS 28 USING THE CLONE MODE 29 COPY MODE eerie 32 COPYING ON A BUTTON BY BUTTON BASIS 32 COPYING THE JOG DIAL INFORMATION 34 OTHER FUNCTIONS 36 LIGHTING BUTTON 36 LUMINOUS BUTTONS 36 SETUP tette 36 JOG DIAL COMMAND FUNCTIONS LISTING 39 SPECIFICATIONS 43 2 l 2 HSITSNA MAIN FEATURES amp FUNCTIONS PROGRAMMABLE LEARNING FUNCTION Can easily be programmed to learn the codes for almost any other infrared based remote allowing the remote control functions for many different components to be consolidated conveniently in a single unit This remote controller uses a non volatile
12. LD or VCR functions are selected When functions other than DVD LD or VCR are selected the lt gt button remains inactive 12 Channel A up Y down button Used to controls the up down function of TV tuner or allows one to cycle through the tuner presets 13 MUTE button Used to temporarily mute the sound for preamplifiers receivers etc 4 14 GUIDE button Used to call up the on screen menus used to control DVD players digital satellite systems DSS and other menu equipped systems 15 CLEAR button Used to clear the contents of memory or programmed functions 16 MEMO button Used to program your CD player s track memory or to enter a VCR recording program and can be used to provide the MEMO function included with other components in your system 17 Ten Key pad Surround Mode buttons Used to enter numeric digits useful for finding a specific track on a CD or to tune a preset radio station etc When the function is set to AMP it is possible to choose Surround Mode etc 18 Infrared Transmitter Receiver Window Used to transmit remote control signals based on beams of infrared light to system components To ensure that these signals are properly received make sure that this window is pointing in the general direction of the infrared receiver on the amplifier or other components This window should also
13. NGLISH HSITSNA For REST setups Function Command Note records pause selects repeat mode random play selects display mode selects edit mode eject selects SP LP mode selects delete selects enter SYNCRO recording 42 SPECIFICATIONS System Infrared type programmable remote control Learning and transmission capable infrared carrier requency band 20 to 70 kHz Transmission infrared wavelength band 950 45nm aximum number of programmable codes 407 Power Size AA alkaline batteries x 2 Dimensions 225 H x 65 W x 26 0 mm Weight including batteries 200 g Accessories Alkalin Datt rles eere 2 Product warranty for USA 1 1 Note Depending on the types of codes programmed it may not be possible to program a total of 407 codes 43 19 1 Leanne muore NZL NA UI LAN IB gie pp use Ee Name anced CONTROL RC 1200 MODE ES 2 DOLY os HAL 00000
14. al control 7 and Function buttons 8 which show FULL and delete them from the memory 12 PROGRAMMING THE JOG DIAL Let s use the example of setting as the SIDE B code for the laser disc player 1 Use a ballpoint pen or other sharp point to press the MODE button 1 until the LEARN indicator is displayed and starts to blink Place the laser disc s remote controller so that its infrared transmitter window is facing the infrared signal receiver window on the Marantz remote controller at a distance of about 5 centimeters 2 inches Press the LD Function button 181 Rotate the Jog Dial 7 left or right until is displayed then press and release the ENT button 6 The LEARN and NAME indicators will both be displayed Press the SIDE B button on the laser disc s remote controller continuously until OK is displayed on the Marantz remote controller s LCD indicating that the programming has been completed f AGAIN appears on the LCD some error has prevented the command from being learned If this happens simply repeat the procedure from step 3 When the programming has been completed the remote controller automatically switches to the NAME mode The left hand position on the LCD blinks indicating the character in the name to be rewritten 2 2 HSI1TON3 f you do not wish to rewrite the name simply press the
15. ansmission indicator ndicates when the remote controller is transmitting a signal USE indicator ndicates the status in which the programmed code is output For normal operation the USE indicator is displayed LEARN indicator ndicates when the remote controller is in the LEARN mode It also appears when programming is cleared 6 NAME indicator ndicates when the remote controller is in the AME mode and a function name is being changed MACRO indicator ndicates when the remote controller is in the ACRO programming mode D CURSOR indicator ndicates when the CURSOR CONTROL buttons are in the cursor mode CONTROL indicator ndicates when theCURSOR CONTROL buttons are in a transport control mode such as PLAY STOP etc NOTE e f the LCD flickers when a button is pressed in order to transmit a command the transmission or learning is not possible In Such a case please replace the batteries Operating tip his remote controller uses non volatile memory so that learned codes and macros will be preserved even if the batteries are removed 2 l 2 LOADING BATTERIES The life of the batteries used with the remote control unit is about 6 months with normal use Also be sure to replace batteries earlier when you notice that they are getting weak Do not use alkaline manganese nickel cadmium Ni Cd or other different types of batteries together
16. been darkened for a home theater performance for instance this remote controller has an LCD display which lights up It lights up when the LIGHTING button 19 or any other button is pressed While the LIGHTING button 19 is pressed it lights and when it is released it goes off e Signals can be sent even while the LIGHTING button is held down The display can be set to light for a duration of 0 to 10 seconds Note When the lighting duration is set to O the LCD display will light up only while the LIGHTING button 19 is held down and for 5 seconds after the button is released LUMINOUS BUTTONS The buttons on this remote controller are designed to remain luminous in dim lighting conditions If the buttons are no longer luminous when the remote controller is used in low light recharge them by placing it near a fluorescent or other light source for a sufficient amount of time This should return the buttons to their luminous condition SETUP Switch the RC 5 destination or adjust the time interval between transmissions of macro operations as follows 1 While pressing the MEMO button 1 press the OK Cursor button This will switch the remote controller to the Setup mode Wait 3 seconds e DOLBY THX DTS HALL 36 The Setup mode includes the following items which may be accessed using the and v Cursor buttons 10 Switch d
17. controller through USE LEARN NAME CLONE TX 5 CLONE RX gt USE with the currently selected mode displayed on the LCD 2 MACRO button Used to store a string of consecutive button operations in the memory and also to revise them Pressing it switches the remote controller in and out of the MACRO mode Its status is displayed on the LCD 3 Power ON and OFF buttons Used to turn ON and OFF the power of the amplifier or receiver or turn ON and OFF the power of a source component which has its own ON and OFF buttons 4j Source ON OFF button Used to turn specific sources such as DVD players etc ON and OFF independently from the rest of the system 5 LCD Used to display information about currently selected modes and functions 6 ENT buttons Used to execute a function selected with the Jog Dial 171 There are 2 ENT buttons one on each side so that the remote controller can be used just as easily with either hand The characters on the display can also be programmed 71 Jog Dial Used to select the operation content for each source Ten types of direct operation are possible for each of the 11 functions including LD TV AMP etc After selecting the desired function press either of the ENT buttons 6 to transmit the signal 9 EN 2 HSITSNA 8 Function buttons Used to s
18. cters with spaces if 15 HSITSNA 7 Follow the same procedure to enter D A When finished press the OK Cursor button 10 Pressing OK permanently fixes the newly written characters Similarly the function names can be overwritten by pressing the function buttons Upto 5 characters can be entered in the function display and command display Torewrite the names of the other items in the Command Name indicator use the Jog Dial 7 to select the desired command and repeat from step 5 8 When you are finished rewriting use a ballpoint pen or other sharp point to press the MODE button 1 to return the remote controller to the USE mode The USE indicator is displayed on the LCD and the newly programmed codes now can be used ae ERASING PROGRAMMED CODES Returning to Factory Presets Codes that have been programmed into the memory can be erased in 4 ways by button s by function s by Jog Dial command and by erasing all memory contents 1 Use a ballpoint pen or other sharp point to press the MODE button 1 to switch the remote controller to the LEARN mode so that the LEARN indicator is blinking on the LCD Note Erasing of programmed codes is only possible in the LEARN mode 16 SOURCE 2 l 2 2 Erasing by Button s To clear the codes and names programmed in any of the buttons Press the button co
19. ending unit to call up the CLONE and TX displays CLONE appears at LCD and TX at LCD Se RO MODE 29 I 2 l 2 HSITSNA Use a ballpoint pen or other sharp point to press the MODE button 1 on the receiving unit to call up the CLONE and RX displays CLONE appears at LCD and RX at LCD G Press the OK Cursor button 10 on the receiving unit Press the OK Cursor button 10 on the sending unit The copying operation is now commenced 1v Ws 1231415 During the copying operation the bar displays at LCD on both units start moving from left to right After the entire bar displays have lighted the display at LCD on the receiving unit changes to RX OK and the LCD display on the sending unit changes to TX OK Copying is now completed FINE LL LIN Lv IL FA LII 0298000000 Nee Se em Do not touch either of the remote controllers during the copying operation Doing so may cause copying to fail When copying has failed at an interim point RX NG will appear on the LCD display of the receiving unit Check steps 1 to 5 and repeat 30 Copying takes about 3 minutes to complete if the programming capacity in the sending unit is 100 7T When copying is completed use a ballpoint pen or other sharp point to press the MODE button 1 on both remote I 2 l 2 cont
20. er and no signal is transmitted to the component To cancel the transmission of a programmed macro use the v Cursor buttons 10 STOP button 27 CLEARING MACRO PROGRAMS The following procedure is used to erase macros you have programmed into the remote controller s memory e When one of the function buttons 8 LD in this example is pressed for 3 seconds while holding down the CLEAR button 115 appears at LCD If you wish to continue the clearing operation press the OK Cursor button 10 HSI1TON3 AUX DIS MATRIX MOVIE OSD SLEEP e To cancel the memory clearing operation do not press OK Cursor button 10 and simply touch any other button 28 USING THE CLONE MODE All the codes which have been programmed can be copied altogether into another RC1200 remote controller by a few simple operations Macros and the set up contents will also be copied Note The clone function cannot be used for copying unless the same model RC1200 is used for the remote controllers at the sending and receiving ends 1 Place the light sensor in the head section of the remote controller at the receiving end about 5 centimeters 2 inches away from and directly in front of the transmitter also in the head section of the remote controller at the sending end 2 Use a ballpoint pen or other sharp point to press the MODE button 1 on the s
21. estination version VER 2 e Adjust time interval between transmissions of macro operations 2 MACRO LCD lighting duration adjustment LIGHT VER Switches the type of preset codes contained in the remote controller LCD displays VER while LCD displays either USA or REST USA means that the CD R MD Function button 8 is set to CD R REST means that the CD R MD Function button 81 is set to MD Use the lt and gt Cursor buttons 0 to select the desired version then press the OK Cursor button 19 This will finish the operation and return the LCD to its original state To cancel the setting press any button other than the Cursor buttons 10 To continue the setting press the v Cursor button 10 Note Codes that have been programmed will not be erased even if the VER setting is changed however the NAME indicator displays associated with the Jog Dial command will be changed Also the Jog Dial commands for CD R MD functions that are contained within macros will also change 37 HSITSNA MACRO Adjusts the time interval between transmissions of macro operations When the v Cursor button 10 is pressed LCD displays MACRO while LCD displays STEP One square in LCD is equivalent to an interval of 0 5 seconds allowing intervals of up to 5 seconds to be set The remote controller is set at the factory with an i
22. lapsed remaining total fast forward rewind side A side B display on off automatic music scan selects audio mode repeat A start point repeat B stop point selects chapter or frame activates edit function selects digital audio analog audio CX NR selects tape deck A selects tape deck B auto reverse direction time display tray open close automatic music scan record pause record selects TV or VCR twice normal playback speed ower than normal playback speed still frame one touch recording audio track selector S kip to next program arker HS index search next VHS index search previous channel marker goes to previously se lected channel selects TV or VCR audio track selector favorite users and channel lists alternate audio chan nel languages brings up on screen channel logos select broadcast or cable antenna record one touch recording no outpu no outpu no outpu no outpu no outpu no outpu no outpu no outpu no outpu no outpu activates on screen display selects title menu zoom mode on off selects main menu digit entry 10 selects setup menu selects angle selects subtitle resume function selects audio Note selects input source increments track num ber activates SYNCRO re cording records pause activates program mode tray open close display mode finalizes writes TOC records blank activates repeat mode E
23. ncerned twice while holding down the CLEAR button 115 When the codes are cleared the button returns to its factory presets or it is left empty Jog Dial codes can be cleared in the same way turn the Jog Dial to call up the name of the command whose codes are to be erased and press the ENT button 6 either the left one or the right one twice while holding down the CLEAR button 15 and the codes and command names memorized in the button will be cleared When the codes are cleared the button returns to its factory presets or itis left empty To erase codes programmed for the CLEAR button 15 simply press the CLEAR button 15 continuously for seconds As an example let s clear the PLAY command from the laser disc player command set 1 While holding down the CLEAR button 15 GS 5 jo e lt gt e e AUTO DOLBY THX DTS HALL 2 Press the OK Cursor button 0 twice 17 HSITON3 Erasing Jog Dial Codes To clear all codes and names previously set for each of the functions LD TV etc Press the function button whose codes are to be cleared When both the left and right ENT buttons 6 are pressed simultaneously while holding down the CLEAR button 15 CLR appears at LCD CG 8 amp 1 ED ED ED AUTO DOLBY THX DTS While h
24. nterval of 1 second as indicated by Adjust the interval between transmission of operation codes using the lt and gt Cursor buttons 10 then press the OK Cursor button 9 To cancel the setting press any button other than the Cursor button 10 LIGHT Adjusts the LCD display lighting duration When the or v Cursor button 10 is pressed TIME appears at LCD Every m at LCD represents a second and a lighting duration of up to 10 seconds can be set The unit is set at the factory with a duration of 5 seconds When is set only the LIGHTING button 19 can be used to light up the LCD display no other buttons can be used to perform this operation Press the lt Cursor button 10 to decrease the lighting duration conversely press the button to increase it After setting the duration press the OK Cursor button 101 To cancel the setting press any button except the Cursor button 110 Tocontinue with the setting press the or v Cursor button 1101 38 JOG DIAL COMMAND FUNCTIONS LISTING Each of the 10 Jog Dial commands on the LCD has 5 character labels attached for pre programmed remote commands These commands can be used with various Marantz A V components or other components using the Phili
25. ocated at the top of the remote controller Use a ballpoint pen or other sharp point to press the MODE button 1 until LEARN is displayed and starts to blink Each time the button is pressed the display cycles through the modes one by one in sequence LEARN NAME CLONE TX CLONE RX USE etc The USE mode is selected when the MODE button is pressed after an operation in the LEARN NAME or other mode 2 Place the laser disc s remote controller so that its infrared signal transmitter is facing the infrared signal receiver on the Marantz remote controller at a distance of about 5 centimeters 2 inches 3 If the cursor is not aligned with the control mode after the LD function button 8 on the remote controller has been pressed press the lt e gt CURSOR CONTROL switching button 11 to display AUTO DOLBY THX DTS MATRIX MOVIE 2 OSD SLEEP CO LN a 4 Press the PLAY button 10 gt OK The LEARN indicator changes from blinking to continuously lit Now release the button Se 5 Press and hold the PLAY button on the laser disc player s remote controller The remote controller has finished learning the command when OK appears on the LCD f AGAIN appears on the LCD some error has prevented the command from being learned If this happens simply repeat the procedure from step 11
26. og Dial 7 to select the page for which you wish to enter a new name Press the down Cursor button and move the blinking location to the Jog Dial 14 4 The left hand edge of LCD B now blinks to indicate that the character at the blinking location can now be overwritten New characters entered will be written over the top of the current character so that the current character is erased Use the lt and gt Cursor buttons 10 to select the characters to be rewritten 5 Use the ten key pad 17 select the desired alphanumeric characters Pressing the number buttons on the ten key pad will cycle through the alphanumeric characters as follows Ten keypad Press press again press again etc 1 A gt B gt C gt 1 gt A D gt E gt F gt 2 gt D G gt H gt lI gt 3 gt G JSRSLS 4 J M gt N gt O gt 5 gt M 0 8 6 S2T2U27o8S VV X 8 V Y gt Z gt gt 9 gt Y SPACE gt gt gt 90 SPACE 6 Therefore to enter the letter L press the 4 key on the ten key pad 17 3 times in a row to cycle from J to K to L XI Once the desired character L appears press either of the lt or gt Cursor buttons 10 and the L will be permanently written over the former character Press the 0 key in order to replace unneeded extra chara
27. olding down the CLEAR button 15 press both the left and right ENT buttons 6j TI CI nnm r 9 n go ahead with the clearing operation press the OK Cursor button 10 Clearing the codes returns all ten of the command names in the Jog Dial to their factory presets or they are left empty LCD will also be either returned to its original display or left empty To cancel the memory clearing operation do not press OK Cursor button 10 and simply touch any other button 18 4 Erasing Codes by Function This procedure clears all the codes and names programmed for the LD TV or any another function When the button for the function to be cleared is pressed twice while holding down the CLEAR button 15 CLR appears at LCD To go ahead with the clearing operation press the OK Cursor button 10 2 2 CD ES CG AUTO DOLBY THX DTS MATRIX MOVIE 2CH OSD SLEEP This will return the button to its factory presets or leave it empty if no factory presets are available Accordingly the LCD will return to the factory preset displays or will simply be empty Tocancel the memory clearing operation do not press the OK Cursor button 10 and simply touch any other button 5 Erasing All Memory Contents This proced
28. on 6 is pressed Page numbers cycle up or down for example gt O gt B gt or E gt etc depending on which way the Jog Dial 7 is rotated The last page position for any given command function is retained in the memory even if the remote controller is switched to the command function for another component Last Memory 9 2 l 2 HSITSNA If itis left for approximately 1 minute without pressing any buttons all items on the LCD will go off except the function indicator Even if the display goes off the remote controller will retain the status established before the display went off When any button is pressed the display will appear on the whole LCD display LEARN MODE The remote controller is capable of learning and memorizing the remote control codes used by almost any other remote controller you may already own e If no commands have been programmed for a particular function button the remote controller will transmit whatever codes have been factory preset The following example shows how to program your remote controller and how to use the codes for a laser disc player LD A different code can be programmed for each function in each one of the buttons The COPY mode described later on page 34 comes in handy if the same code is to be sent by all the functions The remote controller infrared receiver is l
29. ps RC 5 remote control language without DSS function You can easily replace the factory supplied remote command codes with different codes from other brands of component Most of the supplied functions apply to a wide variety of component from many companies The following list shows the remote code assignments for the Jog Dial commands for each of the 11 Function buttons as supplied from the factory You can add or replace Jog Dial commands including re naming them if you wish in order to customize the remote controller for your own particular selection of A V components Note selects surround mode switches analog digital input switches attenuator for analog input selects NIGHT mode for Dolby Digital activates multi room mode activates 6 channel in put increases treble decreases treble increases bass decreases bass FM band AM MW band Long Wave band mono stereo muting mode selector programmed preset channel scan selects station mode selects AF function selects PTY function selects display func tion selects DSR wave range 2 l 2 HSITON3 Note alternate channel 100 s selects video information smart picture smart sound smart channel advance activates on screen display menu CD changer next disc CD changer previous disc activates text function shuffle play function repeat function tray open close automatic music scan time display e
30. rollers to call up the USE display Note If RX NG is displayed all the receiving unit s buttons which were programmed will be returned to the factory presets 5 31 COPY MODE In the copy mode the preset codes or programmed codes stored in the buttons can be transferred copied to other keys as desired The information that will be copied includes not only codes but also names which have been assigned Information can be copied on a button by button basis and Jog Dial codes can be copied Buttons which are excluded from the copying process are the MODE button 1 MACRO button 2 lt e gt button 11 and function buttons 8 HSITON3 COPYING ON A BUTTON BY BUTTON BASIS As an example the information stored in 1 17 on the ten key pad for the LD function will be copied here to 1 17 on the ten key pad for the DVD function 1 Use a ballpoint pen or other sharp point to press the operation MODE button 1 to call up the LEARN display LEARN now blinks on the LCD display gt 2 Press the MEMO button 16 for seconds The learn mode of the MEMO button is established first and after 3 seconds it changes to the COPY mode gt appears at LCD gt DOLBY THX DTS 32 Select 1 of the LD function button on the copy source Press the LD function bu
31. tton 8 and then press 1 on the ten key pad 117 for seconds The display at LCD changes from LD to 1 and the characters 1 stops blinking and remain lighted CPYc _ at LCD 2 2 TUNER Qe e amp amp AUTO DOLBY THX DIS 1111111 TTS The copy source has now been established The copy destination is selected next Press the DVD function button 8 and then press 1 on the ten key pad 117 for seconds The character 1 stops blinking and remain lighted 9 CD CG 68 ED Gs e amp amp AUTO DOLBY THX DTS HALL MATRIX MOVIE 2CH OSD SLEEP When copying finishes the OK display appears at LCD appears again at LCD Now repeat steps 3 and 4 When copying is completed press the MODE button 1 and call up the USE display 33 HSITSNA COPYING THE JOG DIAL INFORMATION As an example 1 DISC for the CD function will be copied here to 1 OSD for the DVD function 1 Use a ballpoint pen or other sharp point to press the operation MODE button 1 to call up the LEARN display LEARN now blinks on the LCD display MODE 2 Press the MEMO button 16 for 3 seconds The learn mode of the MEMO button is established first and after 3 seconds it changes to the COPY mode CPY
32. ure clears resets all the data programmed Once all the data is cleared the memory is returned to its factory preset status When ON and OFF of the POWER buttons 3 are pressed simultaneously while holding down the CLEAR button 15 ACLR appears at LCD HSITON3 To go ahead with the clearing operation release the buttons and press the OK Cursor button 10 Once the data is cleared the codes are either returned to their original display or left empty LCD is similarly returned to its factory preset or left empty All the macro programs are also cleared To cancel the memory clearing operation do not press the OK Cursor button and simply touch any other button After the OK Cursor button 10 is pressed clearing the entire memory will take approximately 10 seconds PROGRAMMING MACROS Macros make it possible to use a single function button to perform more complex series of operations that would normally require pressing several buttons A single button can be programmed to perform up to 10 steps in sequence A typical example of such a series might be as follows e Turn the main amplifier power ON gt Switch the function to DVD Set the Surround Mode to Pro Logic Switch the TV to video input gt Set the DVD player to PLAY No signals may be transmitted during macro programming The various steps that make up a macro are set initiall
33. witch the remote controller to the command sets for specific sources amplifier receiver etc thereby allowing a single remote controller to control up to 11 different components To use these buttons to switch the amplifiers source press the desired button twice within 2 seconds The AMP button 8 is used only to switch the command set of the remote controller itself and therefore does not transmit any signal Further the function buttons may also be programmed to execute macros A macro allows a complex string of operations to be performed in series simply by pressing a single button One button can be programmed to learn sequences containing up to 10 commands The following is an example of a macro sequence Turn the receiver ON Switch the function to DVD Set the Surround Mode to Dolby Digital Switch the TV to video input Set the DVD player to Play 9 VOLUME up Y down button Used to adjust the volume on receivers and other components equipped with volume control 10 CURSOR CONTROL buttons Used to operate on screen and other displays used by amplifiers and other components as well as to operate the PLAY STOP PAUSE EXT and PREVIOUS functions of each source 11 lt gt CURSOR CONTROL switching button Used to switch the function of the CURSOR TRANSPORT CONTROL buttons 19 between CURSOR and TRANSPORT CONTROL with the currently selected function displayed on the LCD when the DVD
34. y 1 with each button pressed For example press LD PLAY AUTO DOLBY THX DTS Each function button can be programmed to perform up to 10 steps in sequence 21 HSI1TON3 If while programming no buttons are pressed for approximately 1 minute the remote controller will automatically return to normal mode and no macro will be programmed in the memory When you are finished programming macros use a ballpoint pen or other sharp point to press the MACRO button 2 LCD G will display END and the display will return to normal Macros cannot be programmed for the MODE 1 MACRO 2 lt gt 11 VOL 9 MEMO 16 or CLEAR 15 buttons Although function operations in the acro Mode can be programmed more than once only the first function memorized in the ten function buttons including LD CD TV but not the AMP button will be sent from the remote controller the amplifier or receiver function will change For this reason it is not possible to select multiple amplifier functions in a macro button If the AMP button is programmed the same operations as those in the other function buttons will be performed Therefore when executing operations in the Macro Mode what happens is that starting with the second function operation only the function mode of the remote controller is changed and no signals are sent
35. y be stored in any macro the tenth step will be erased if a step is inserted when the total number of steps is already 10 ED ES DOLBY THX DTS HALL MATRIX MOVIE 2CH 050 SLEEP To erase a step a macro after step 3 call up the number of the step to be erased and press the CLEAR button 15 C AUTO DOLBY THX DTS HSI1TON3 If while editing macros no buttons are pressed for approximately 1 minute the remote controller will automatically return to normal mode and no macro changes will be programmed in the memory 4 When you are finished editing macros use a ballpoint pen or other sharp point to press the MACRO button 2 END will be displayed on LCD and the display will return to normal Note When the Jog Dial 7 has been programmed in a macro changing the function immediately before causes the jog commands immediately after to be automatically changed to the commands of the new function The commands are changed to the commands on the same page number of the new function USING MACROS The following procedure will show how to use the function buttons for which you have programmed macros 1 Press the Function button 18 for the desired macro for 3 seconds MACRO is displayed on LCD 8 for approximately 1 second after which the number of steps in the macro is displayed on LCD O 9 5
36. y to be sent one after another in 1 second intervals however these intervals may be shortened to as little as 0 5 seconds or lengthened to as much as 5 seconds using the Setup mode n the macro mode the number of steps the macro contains is displayed on LCD Macros may be programmed for each of the 11 function buttons from LD to AMP 1 Use a ballpoint pen or other sharp point to press the MACRO button 2 until the MACRO and LEARN indicators are displayed blinking on the LCD MTR Press the Function button 18 for which you wish to program a series of operations In this case let s use the example of the laser disc player Press the LD Function button 181 Example The LCD G will display LD M The characters displayed at LCD are as follows However when a function name has been overwritten M appears for the first 2 or 3 characters LD M DVD M TV M DSS M VCR M AUX M TUN M CD M TP M AMP M CDR M or MD M for remote controller set for MD e macro has already been set for the selected function button the LCD will blink Also the number of steps in the macro is displayed on LCD Press the buttons for the operations you wish to program as a macro in the sequence you want the macro to program them The name of the button pressed appears on LCD The number of steps in the macro is displayed on LCD and this number increases b
Download Pdf Manuals
Related Search